REPAIR / MAINTENANCE OF E/M INSTALLATION, REPLACEMENT OF INSTALLATION SIGNAGE BOARD AND REPAIR TO ROOF, CHAJJA, FESCIA AND PARAPET WALL INCL MISC REPAIR WORK IN TECHNICAL AREA AT AF STN KALAIKUNDA

Amount

Dismantling post of struts (Wood/Steel/RCC) any section,including taking out embedded portion in concrete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in & raming earth/ broken rubble mixed with earth around, in layers n. exc. 25cm, watering, & removing surplus soil to a distance n exc 50m & making good surface in soft/loose soil.

Dismantling water tanks capacity exceeding 300 litres but not exceeding 500 Litres and removing to store complete all as specified and as directed.

Dismantling water tanks capacity exceeding 500 litres but not exceeding1000 Litres and removing to store complete all as specified and as directed.

Taking up or down, steel tubing 15 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Taking up or down, steel tubing 20 mm bore, and connection including cleaning for re-fixing or removal from site of work complete all as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings including translucent sheet complete all as specified and as directed by Engineer-in-charge

Taking down SWR pipes (any size or pattern), including all fittings, 'T', bends,etc., including removal to store for taking credit (measured overall as fixed along the centre line over fittings and accessories), complete all as directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for disposing the rubbish to the out side of MD land complete all as specified

Taking down aluminium chowkats of frames with shutter not exc1.50 sqm each (without taking off shutter from the frame) of any description any type complete all as directed.

Taking down aluminium chowkats of frames with shutter exceeding 1.50 sqm and not exceeding 4 sqm each (without taking off shutter from the frame) of any description any type.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) exc. 1.5 Sq. M but not exc. 4.0 Sq M each, complete all as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exc. 1.5 Sq. M complete all as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, complete all as directed.

Plain cement concrete type B2 (1:3:6 )using 40 mm graded crushed stone aggregate) as in foundations fillings and mass concrete or embeding in fencing post complete all as specified and as directed.

Dismantling barbed wire, any type and in any position & separating them the serviceable & unserviceable materials and removing the unserviceable wire /barbed wire from work site as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Dismantling fencing wire mesh, any type and in any position & separating them the serviceable & unserviceable materials and removing the unserviceable wire mesh from work site as directed

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc. complete all as specified and directed by Engineer in charge.

Demolition of Reinforced cement concrete of any description and in any position by mechnically means otherwise specifically provided for disposing the rubbish to the out side of MD land complete all as specified

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) disposing the rubbish to the out side of MD land complete all as specified

Taking down cement plaster on stone/brick/concrete surfaces including racking out joint, hacking for key, scrubbing down with water complete all as specified and as directed.

Restraining & rescuring including making good staples etc. Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings & straining & fixing to any type of standard rails straining bolts, including, securing or tying at crossings with & provision of new galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S & F hot rolled low tensile structural steel of grade E165 as per IS 15911: 2010 as in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. Wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar works complete all as specified and as directed.

Supply and fixing galvanized steel chain link fence fabric of mesh size 50 mm X 50 mm, made out of 4 mm nominal dia of mesh wire conforming to IS 2712-2003 and having zinc coating of type heavy as laid down in IS-4826 including line wires/ binding complete all as specified and as directed Make Tata or equivalent make as approved by GE

S&F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 Rolled mild steel Roof trusses (framed), trussed purlins crane gantries, rails & fastenings & heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc.complete all as specified and as directed.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles complete all as specified and as directed.

S&F flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting etc conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed.

S&F Mild steel screw bolts (machine made) with hexagonal /square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut, length of bolt exc 5cm but n exc 10cm long dia of shank 11 to 15 mm complete all as specified and as directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or srewed both ends, each screwed end to be fitted with washers and one hexagonal or square nut exceeding 22.5 cms and not exceeding 30 cms and diameter of neck 16-20mm all as directed and specified by Engineer-in-charge.

M&L AIPL ABRO general purpose silicon sealant USA 1000 GP marketed by AIPL marketing pvt ltd to stoping any leakage and applying in each screw/hole in roof sheeting of any height of building as per manufacturer,s instuction complete all as specified.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height. Complete all as specified and as directed.

S & F hot rolled medium and high tensile structural steel of grade E165 as per IS 15911: 2010 as in framed work such as grills, grating, etc., with ends of bars of shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework water tanks and similar work complete all as specified and directed by Engineer-in-charge.

S&F Rolled mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with & including either hooks & hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails & guides) & hanging; also fastening & fixing complete GDE Fe410-0 Quality B complete all as specified and directed by Engineer-in-charge.

S&F Mild steel, plain black sheet 1.25mm thick in wall cladding, steel gates & similar work, cut to size, holes punched; including round headed screws, clout nails or rivets & fixed to wood or steel framing with plain 40mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed by Engineer-in-charge.

Preparation of newly or previously untreated steel surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed by Engineer-in-Charge

Preparation of old steel surface of any description not exceeding 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed by Engineer-in-Charge

Material and Labour for water proofing treatment to existing RCC roof in following steps :- (a) Complete removal of the existing water proofing treatment with and including old padding concrete from roof surface and cleaning surfaces by brushing etc and washing down with water and removing durt, dust etc and removing debris from premises completed. (b) Providing 40 mm thick PCC 1:2:4 type B-O (using 12.5mm graded crushed stone aggregate) as in roof padding /surfaces and including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work complete all as specified and as directed. (c) 10 mm thick bedding layer on fair faces of bricks/ concrete surfaces in CM 1:4 mixed with liquid water proofing compound @0.25% or manufacturer,s instruction by the weight of cement or as per manuacturer instruction complete all as specified and directed. NOTE :- (a) Rate for supply of liquid water proofing compound are inclusive in the above item. (b) Applying a coat of cold applied polymeric modified bitumimous primer @0.30Kg/Sqm. (c) Providing APP based polymeric membrane minimum weighing 3.0Kg/Sqm for approachable/non approachable roof at any height of building and minimum 3mm thick (mineral top finish, reinforced with polyester non-woven fabric (weight not less than 160 gm/sqm) laid over and including on a coat of industrial bitumen85/25 @ 1.2 Kg/Sqm or manufacturer,s instruction by torch application as per the manufacturer instruction with side and end overlap of 100mm.

Taking down and carefully removal of old cement plaster and wall finishing incuding raking out joints, hacking for key and scrubbing down with water etc and cleaning the surface to receive new plaster in static water tank of any depth as per site condition etc with necessary scaffolding and protective gear and safety devices as per rule 4 of the Prohibition of Employment as Manual Scavengers and their Rehabilitation Rules, 2013 including disposal of rubbish outside the premises of MD land as per the direction of engineer in charge.

M&L for providing and applying 3 coats of water proofing acrylic Polymer confirms to DIN 1048 by mixing of 1kg WP Polymer and 1.25 kg of cement for first coat, than laying second layer of Fibre glass cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less than 10 cm. then finaly apply 2 coats of WP polymer cement slurry to entire surface and necessary cureing in static water tank etc with necessary scaffolding and safety measures and other material is required as per direction of manufacturer,s deemed to included complete all as specifed (Manufacturer name of chemical shall be : Fosroc/Sika/Pidilite/BASF) The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate

M&L for providing and application of 1:4 cement sand plaster in two layers of 15 mm thick each layer below and above fiber glass cloth admixed as per manufacture,s instraction with integral water proofing compound Rheomac 707 @ 130 ml per bag of cement over the entire area of concrete in static water tank etc with necessary scaffolding and safety measures and other material is required as per direction of manufacturer,s deemed to included complete all as specifed (Manufacturer name of chemical shall be : Fosroc/Sika/Pidilite/BASF) The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate

M&L for fixing of MS nozzles @ 400 mm c/c of required depth and manufacturers instruction injecting non shrink cementitious grout admixture with cement slurry at the rate of per bag of cement as per manufacturer’s instructions. (Manufacturer : Fosroc/Sika/Pidilite/BASF) through the prefixed nozzles under pressure using grout pump to fill all possible pores and gaps left within the concrete mass. When the flow of grout stops, or when the grout flows out of the adjacent nozzle, pumping is stopped and the nozzle is tied up and allowed to set for 24 hours all as directed. (NOTE :-The MS nozzles shall be sealed off with a quick-setting waterproofing agent. Grouting operation is carried out through the next nozzle till the entire area is covered. The grouting holes shall be finished by removing the nozzles and finishing flush with the surface up to any height including all necessary scaffolding and safety measures all as specified and directed. The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate).

Repairs to crack of brick work including preparing of surface cleaning thoroughly and applying SIKA Top -122 cement based polymer modified trixotropic mortar or any other similar component as per manufacturer instruction finished to match with the existing complete all as specified and as directed.

Preparation of concrete surface of chajja/beam/slab thoroughly abraded to remove all laitance, any trace of loose plaster, oil, grease, paints and any other materials are to be removed by wire brushing the surface. The entire surface shall then be washed thoroughly with plenty of water and then allowed to dry. Defective concrete surfaces cut back to a sound base by chipping and removed loose concrete. Smooth surfaces to achieve by chemically roughened up to 10 Mtr height including all necessary scaffolding and safety measures all as specified and directed. .(The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate).

M&L for cleaning to expose corruded reinforcement of chajja/beam/slab by wire brushing, emery paper or by mechanical means and to remove all loose scale and corrosion deposit and washing complete and providing additional reinforcement TMT bars of approved make, cut to length by electro welding method and applying one coat of rust removing chemical along its full circumference up to 10 Mtr height including all necessary scaffolding and safety measures all as specified and directed. (Manufacturer name of chemical shall be : Fosroc/Sika/Pidilite/BASAF) The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate).

M&L for high built repair ready mix mortar or concrete to expose corroded reinforcement of chajja/beam/slab with bonding agent as per manufactures instruction (Manufacturer : Fosroc/Sika/Pidilite/BASAF) proper compaction and finished to proper level upto a depth of 50mm with and including provision of formwork to the affected portion up to 10 Mtr height including all necessary scaffolding all as specified and directed.(entire operation shall be done by the approved manufacturer or their authorized applicator and deemed to be included in the unit rate)

M&L for fixing of MS nozzles @ 500 mm c/c of required depth and manufacturers instruction injecting non shrink cementitious grout admixture with cement slurry at the rate of per bag of cement as per manufacturer’s instructions. (Manufacturer : Fosroc/Sika/Pidilite/BASF) through the prefixed nozzles under pressure using grout pump to fill all possible pores and gaps left within the concrete mass. When the flow of grout stops, or when the grout flows out of the adjacent nozzle, pumping is stopped and the nozzle is tied up and allowed to set for 24 hours all as directed. (NOTE :-The MS nozzles shall be sealed off with a quick-setting waterproofing agent. Grouting operation is carried out through the next nozzle till the entire area is covered. The grouting holes shall be finished by removing the nozzles and finishing flush with the surface up to 10 Mtr height including all necessary scaffolding all as specified and directed. The cost of entire operation shall be carried out by approved manufacturers or their authorized applicator and deemed to be included in unit rate).

M & L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and as directed

S&F Mild steel TMT bar 6mm to 8mm dia cut to length, bent to shape reqd, incld cranking, bending spirally for hooping for columns , hooking ends & binding with & including mild steel wire ( annealed) not less than 0.90 mm dia. or securing with clips complete all as specified and as directed.

M & L pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet corresponding to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

M & L pre-painted hot-dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50 mm thick, of an approved colour and having yield strength of 550 MPa as in ridge/ valley/ gutter fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

M & L brick work with fly ash bricks straight or curved on plan exec 6 M mean radius with old size bricks in CM (1:4) complete all as specified and as directed.

M & L for brick work with fly ash brick class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

M&L for rendering 5mm thick cement plaster CM 1:3 on chajja /soffits with integral water proofing compound on brick work or concrete surfaces finished surfaces even and smooth with using extra cement ,over and including two coat of damp proof ultra through mechanical mean as directed by manufacturer,s complete make Asain or equivalent make of Sika/Fosroc/BASAF including all necessary scaffolding and safety measures complete all as specified and directed Note: - (Water proofing compound and Damp proof ultra or equivalent make will be deemed to be included in quoated rates

Materials and Labour for rendering 15 mm thick, cement plaster, in cement mortar (1:4) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5mm thick cement plaster CM 1:3 on ceiling including fair faces of brick work or concrete surfaces finished even and smooth (without using extra cement) complete ll as specified and directed.

Materials and Labour for rendering 5 mm thick, cement plaster, in cement mortar (1:4) mixed with water proofing compound as per manufactures instructions over and including 10mm thick backing coat in cement mortar (1:4) on fair faces of brick work or concrete surface in walls finished surfaces even and smooth with using extra cement ,over and including two coat of damp proof ultra through mechanical mean as directed by manufacturer,s complete make Asain or equivalent make of Sika/Fosroc/BASAF including all necessary scaffolding and safety measures complete all as specified and directed Note: - (Water proofing compound and Damp proof ultra or equivalent make will be deemed to be included in quoated rates

Materials and Labour for rendering 10 mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Materials and Labour for rendering 15mm thick, cement plaster, in cement mortar (1:6) on surface fair face of brickwork in walls and finishing surface even and smooth without using extra cement, complete all as specified and directed.

Material and Labour preparartion of new plastered surfaces by means mechnical process / Machine as directed by manfucaturer through authorised applicator of manufacturer,s and applying two coat of Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to new plastered or unplastered surfaces on walls including preparation of surfaces, complete all as specified and directed.

M&L for complete removal of existing treatment from walls, ceiling, etc and applying two coats acrylic distemper on walls, ceiling over with and including a coat of primer complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

M & L for applying Two Acrylic Exterior Emulsion paint in camouflage pattern (Three colours as approved by GE) (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand over a coat of exterior wall primer on new concrete/wall surfaces up to 10 Mtr height including all necessary scaffolding complete all as specified and directed.

M&L for preparation of new plastered or un -plastered from walls, and applying two coats acrylic distemper on walls, over and including a coat of 1 mm thick white wall care putty and a coat of primer as per manufactrer,s instruction complete all as specified and as directed.Make;Berger (Bison)/J&N(Jensolin)/Asain Piants(Tractor)/Nerolac(Beauty)

Material and Labour for applying two coats of cement-based paint, white or tinted to new plastered surfaces on walls including priming with alkali resistant priming paint and including preparation of surfaces complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceilings and applying three coats of white wash complete all as specified and as directed.

M & L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparing old decorated plastered or unplasterd surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing and sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and removing extra wall papdi ,peel off wall papdi by sand paper and making good with putty as per existing thickness and applying one coat of white washing on the wall all as specified and directed

M&L for preparing old decorated plastered or unplasterd surfaces of ceiling including cornices, pilasters and other wall features etc by brooming down or steel wire brushing and sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and removing extra wall papdi ,peel off wall papdi by sand paper and making good with putty as per existing thickness and applying one coat of white washing on the ceiling all as specified and directed

M & L for applying one coat o f Acrylic Exterior Emulsion paint (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand including preparation of old concrete/wall surfaces of any type and description include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots complete all as specified and as directed.

M&L for preparing old decorated plastered or unplasterd surfaces of wall including cornices, pilasters and other wall features etc by brooming down or steel wire brushing and sand paper, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and removing extra wall papdi ,peel off wall papdi by sand paper and making good with putty as per existing thickness and applying one coat of cement base paint on the wall all as specified and directed

Material and Labour for complete removal of existing treatment by means mechnical process / Machine as directed by manfucaturer through authorised applicator of manufacturer,s and applying two coat of100 % Acrylic Exterior Emulsion paint in camouflage pattern (Three colours as approved) (Berger,Weather coat Advanced XP Brand/Asain Paints :Apex ultima Brand /ICI:Dulux Weather shield Max Brand/J&N:Safeguard Optima Brand painting over and including a coat of primer to old plastered or unplastered surfaces on walls including preparation of surfaces, up to 7.5 Mtr height including all necessary scaffolding and safety mesures complete all as specified and directed Note

M&L for cement concrete 25mm thick type B-0, 1:2:4 (12.5 mm graded aggregate) as in base of flooring, finished even and rough to receive the top layers all complete as specified and as directed

M&L 75 mm thick Cement concrete type B2 1:2:4 (using 40 mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth with out using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and as directed.

Material & Labour for 100 mm thick Plain cement concrete ( 1:2:4 ), type B-1 (using 20 mm graded stone aggregate), as in flooring/ hard standing finishing the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for repairing of crack in wall/roof by the following method i) Cutting the crack by grinder and clean the ii) Filling the crack with cement concrete ( 1:2:4) 12.5 mm aggregate with mixing crack filler. iii) Fixing chicken wire mesh over the crack surface and Rendering with cement mortar 1:3 complete all as specified and as directed.

M&L cement concrete (1:4:8) type D-2 (40 mm graded stone aggregate) as in sub base Mass Concrete complete all as specified.

M & L for cement concrete M15 (Nominal Mix) using 12.5 mm nominal size graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs, slab staging for water tanks and the like including weathering, slightly rounded or chamfered angles and throating including necessary formworks complete all as specified and directed by Engineer- in-charge.

M & L for RCC M20 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and as directed.

M & L for RCC M20 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate as in columns, pillars, piers, posts and struts complete all as specified and as directed.

M & L for RCC M20 (Nominal Mix) using 20 mm nominal size as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed.

M & L for precast cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces fair faces, including chamfers, weatherings, throating etc. and setting in cement mortar (1:4) complete with joints to match complete all as specified and as directed

M & L Form work to soffits of suspended slabs such as roof slabs, floor slabs and similar work exceeding 200 mm thick (Horizonal or sloping) for fair finished surfaces of concrete as directed.

M & L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and as directed.

M & L for formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete complete all as specified and as directed.

Materials and Labour for, Non - Skid Ceramic tiles, coloured, 7 to 8 mm thick area of each tile exceeding .11 sqm but not exceeding 0.18 sqm,conforming to IS 15622, Grade B II, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over and including 15 mm thick screed bed or bedding layer of cement mortar (1:4),complete all as specified and directed.

Materials and Labour for, Digital glazed ceramic coloured tiles, 600 X 300 X 8mm thick, conforming to IS 15622, Grade B III, on vertical surface of wall such as dados,skirting etc, set and jointed in neat cement slurry and pointed in white or colour cement to match over and including 10 mm thick screed bed or bedding layer of cement mortar (1:4), complete all as specified and directed.

M & L for machine cut Kota stone slab flooring 20 to 25 mm thick over cement screed bed of 15 mm thick in cement mortar 1:3, laid and jointed with grey cement slurry, mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Cleaning of PVC water tanks of capacity exceeding 300 litres but not exceeding 500 litres including chemical treatment with Anti-bacterial agent consisting of following process: - Dewatering the tank with submersible pump, de-silting and removing of left over dirty water up to 100 to 150 mm in the bottom of the tank and sludge with special sludge pump, cleaning of walls and ceiling with special mechanized high pressure jet machines by rotary jet system at 100-120 Bar pressure (120 Kg /sq cm) which dislodges the layer of dirt, algae, fungus stuck on its surface usage of scrubbing machines for old stains and cleaning chemicals if required of make Eureka Forbes Ltd, floor or equivalent make of the dirty tank should be thoroughly cleaned up by fry jet cleaner to accumulate all dirt ,the remaining sludge should than be removed by sludge pumps, the dirt silt and other foreign material should further be removed by Industrial Vacuum Cleaners to make the floor totally dirt free, application/spraying of Anti-Bacterial chemicals to ensure total sterilization of tank from the inside, inside of the tank should be treated with specially developed 4 ft long ultraviolet Radiator to kill further floating bacteria/virus in order to make the tank totally clean, bacteria free and safe for storage of drinking water. All the above operations should be executed by trained workers and technicians, properly dressed along with gum boots, to work as per the direction of Engineer in charge.

S&F in repairs PVC tank cover with locking arrangement for 500 ltrs capacity of approved make complete all as specified & as directed.

Removing of plants including roots by dismantling of brick work/PCC/RCC including necessary scaffolding any type any location /height (ie roof, paraper walls near pipes etc) and applying acid after revoving roodts for preventing the regrowthing and making good the disturbed portion using PCC 1:2:4 type B0 and plaster in CM 1:3 (size of disturbed portion 150x150x150mm) completer all as specified and directer by Engr-in-charge.

Refixing of old steel tubing and connection with new fittings ISI Marked in new or old position (wall, ceiling, floors, etc) of 15 mm bore complete all as specified and as directed.

Refixing of old steel tubing and connection with new fittings ISI Marked in new or old position (wall, ceiling, floors, etc) of 20 mm bore complete all as specified and as directed.

Supplying & fixing to walls and ceiling 15 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceiling 20 mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

S&F in repair Gun-metal, globe or gate valves 15mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and directed.

Cutting chases in brick walls to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., not exceeding 10 cm girth and making good the same with cement concrete M15 (Nominal Mix) using 12.5 mm nominal size coarse aggregate or cement mortar 1:3 including necessary plaster and pointing in cement mortar 1:3 complete all as specified and as directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer complete all as specified and directed.

Supply and Fix,4.8 mm thick tinted glass, superior quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from aluminium frame work complete all as specified and directed.

Supply and Fix,4.8 mm thick tinted glass, superior quality and glazing with oil putty in squares exceeding 0.50 Sq M in each pane with and including hacking out old broken glass (any thickness, size, quality or description) from aluminium frame work complete all as specified and directed.

Supply and Fix,3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane complete all as specified and directed.

Supply and Fix,4 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane at any height with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer complete all as specified and directed.

Supply and Fix,4 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sq M in each pane at any height with and including hacking out old broken glass (any thickness, size, quality or description) from frame including providing wooden beads painted with two coat of enamel paint over a coat of primer complete all as specified and directed.

S & F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

S & F unplasticized PVC pipes as per IS 4985: 2000, of class 5, working pressure PN 10 (1 Mpa), plain or socket ended and nominal size 15 including all fittings and fixtures fixed to walls ceiling or in floors with elastomeric sealing ring joints complete all as specified and as directed.

S & F unplasticized PVC pipes as per IS 4985: 2000, of class 5, working pressure PN 10 (1 Mpa), plain or socket ended and nominal size 20 including all fittings and fixtures fixed to walls ceiling or in floors with elastomeric sealing ring joints complete all as specified and as directed.

S & F PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, fixed to walls including all fittings complete all as specified and directed by Engineer- in- charge .

S & F PVC-U, type B as per IS 13592: 2013 single socketed soil waste pipes in any length with rubber ring joints, 110 mm dia, laid in trenches complete all as specified and directed by Engineer- in- charge .

S & F UPVC bends without inspection door (any angle), 110 mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

S & F UPVC branch piece, single (single Y) equal or unequal 110mm dia conforming to IS 14735: 1999 complete all as specified and directed by Engineer- in- charge

S & F in repairs brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and as directed.

S & F in repairs Soap dish Complete all as specified and directed, Make Cat No AQN-CHR- 7731 of Jaquar or equivalent of Kohler/Marc.

S & F in repairs brass chromium plated towel ring, complete all as specified and as directed.

S&F in repairs 32mm bore Brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed complete all as specified and as directed.

S&F in repairs 15 mm nominal size, pillar taps, cast copper alloy body and body components with capstan heads, spindle, washer plate and nut, with screwed shanks and back nut, with or without lettered hot or cold, nickel-chromium plated finish complete all as specified and as directed.

S&F in repairs 15 mm nominal size, nonrising spindle type fancy stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed.

S & F in repairs 15 mm nominal size, nonrising spindle type fancy concealed stop valves as per IS 8931: 1993 made of cast brass including Knob, knob components, divertor & components, nickel-chromium plated finish complete all as specified and as directed

Supply and Fix, in repair bib tap, cast copper alloy, , chromium plated, with crutch or butterfly handle, screwed down, screwed for iron pipe or brass ferrule,15 mm bore and fixed, complete all as specified and directed.

S & F in repairs vitreous china squatting pan, 'Orissa" pattern, size 580 mm X 440 mm white with ‘P’ or ‘S” trap, front or back inlet and integral foot rests, any pattern and including fixing bolt, connector to flush pipe, lime concrete bedding and making connections to flush pipe, connector to branch pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S & F in repairs vitreous china wash down water closet (pedestal pattern), white including thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating, fixing bolt, connector to flush pipe and making connections to flush pipe, connector to branch soil pipe and anti syphonage pipes etc. including sealing the joints and making leak proof using sealant complete all as specified and as directed by Engineer-in-Charge.

S & F vitreous china urinals, bowl (flat back) with flushing rim of size 440 mm X 265 mm X 355 mm with side fixing arrangements with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement; with and including automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe complete all as specified and as directed.

S & F in repairs in repairs thermoplastic seats and covers of grade 2 type, flat with hinging device of bronze or brass with nickel chromium plating complete all as specified and as directed.

S & F in repair Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern to squatt pattern all as specified and as directed.

S & F in repairs 10 litres capacity, low level, syphonic type, white, plastic flushing cistern as per IS 7231: 1994 with inlet, ball valve, float and handle including brackets and 40 mm nominal dia high density polyethylene pipes for flush pipe complete all as specified and as directed.

S & F in repairs wash basins, vitreous china, white, flat back, size 550 mm X 400 mm with and including cast iron brackets (embedded in wall upto 110 mm depth with and including cement concrete M15 (Nominal Mix) using 20 mm nominal size graded crushed stone aggregate or fixing on wall with and including rawl plug and screws), 32 mm nominal size, copper alloy, nickel chromium plated finish waste fittings, including painting of fittings and brackets, sealing gap between wall and basin with silicone sealant, cutting and making good the walls wherever required and connecting to supply pipes, waste pipes, waste fittings etc. with silicone sealant complete all as specified and as directed.

M & L for PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed.

M & L in repair for PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

S & F flexible (coil shaped) PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm connected to PVC waste fittings complete all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 500 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S & F rotational moulded polyethylene double layer water tanks (vertical cylindrical with close top) as per IS 12701: 1996 of 1000 litres capacity hoisted and fixed in position including provision of 20 mm /15 mm dia medium grade GI pipe for connecting inlet, outlet, over flow and washout pipes all as specified and as directed.

S & F in repairs 20 mm nominal size brass float valve, high pressure, with polythene float and flynut, screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair grating doom 100mm dia with waste hole of PTMT minimum weight 25 Gms complete sealed with white cement all as specified and as directed.

S & F in repairs CP fancy type urinal spreader and screwed for GI pipes complete all as specified and as directed.

S&F brass chromium plated hand shower (health faucet) complete all as specified and as directed. Make- Jaquar cat No-ALD-BLK-583 or Marc/Kohler/Parryware)

S & F pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.25 mm thickness, size 105 mm X 60 mm, Profile C, single rebate including hinges, mortar guards, lock strike plate, shock absorbers complete all as specified and as directed.

Supply and Fix, factory made rigid lam PVC door frame of size 100 mm x 50 mm, single rebated with wall thickness of extruded 5mm PVC sheet of density 600 kgs/cum , made by joining 3 Nos. heat bent PVC sheet sections. The inside section of size 90mm x 30 mm shall be made from colour PVC sheet of 5 mm thickness.The inside section shall be covered by sticking two sections of size 35mm and 6 x 45 mm made from 5mm thick plain sheet. The frame shall be mitred cut at two corners and jointed by inserting 4 Nos. 150 mm long brackets of 15mm x15 mm MS square tube. The two vertical members of door frame shall be reinforced with 40mm x 20 mm MS tubes of 19 SWG duly filled with 2nd class hardwood throughout the frame. The door frame shall be fixed to the wall using 100 mm long nikel coated dry wheet screws through the frame by using PVC fastener. Minimum 04 Nos. of screws shall be provided for each vertical member and minimum 02 Nos.for horizontal members etc. as per manufacturers specifications, fixed in opening, complete all as specified and directed.

Materials and Labour 35mm thick for, Factory Made Solid PVC Moulded Door designer Shutter, with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC sheet on back face, supplying & fixing in frame at site as per specification and drawing, complete all as specified and directed.

S & F Factory made flush door shutters, 40 mm thick, solid core of block boards construction, MR grade, commercial type with stiles, rails and lipping of timber as given in Group 2A and Group 2B of Annex B of IS 2202 (Part 1): 1999, both sides face panels of plywood as per IS 710: 2010, internally lipped complete all as specified and as directed.

S & F for 9mm thick prelaminated particle board, exterior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed in aluminium frame work complete all as specified and as directed.

S & F steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

Supply and Fix,steel ventilator with top hung shutter including hinges, steel peg stay, complete with glazing bars, dovetailed or welded, including making good disturbed surfaces as per existing specfication complete all as specified and directed.

Dismantling/taking down unserviceable parts of steel rolling shutters (self coiling types shutters i.e push pull with gear oprating type machnically or moter operated ) area n.exc. 20 Sqm and for repairing and overhauling of rolling shutters and greading/oiling of members of rolling shutters. M&L for preparation of old painted iron and steel surfaces by scraping & rubbing down with sand paper, removing dense and scratches, if any and filling the same with paste filler and applying one coat of synthetic enamel paint complete all as specified. Note : (I) Refixing/welding of rolling shutters duly repaired/overhauled/welded/painted shall be included in the quoted rates of this item. (ii) Fixing & replacing of new parts of rolling shutters shall be included in the quoted rate of this item. (iii) Makes/Size/Specifications of new parts of rolling shutters as per existing specification of rolling shutters. (iv) Any damage or loss of rolling shutter during taking down/dismantling shall be made good by the contractor at his own cost.

Dismantling/taking down u/s parts of steel rolling shutters (self coiling types shutters i.e push pull with gear oprating type machnically or moter operated ) area n.exc 20.00 Sqm and for repairing and overhauling of rolling shutters and greading/oiling of members of rolling shutters. M&L for preparation of old painted iron and steel surfaces by scraping & rubbing down with sand paper, removing dense and scratches, if any and filling the same with paste filler and applying one coat of synthetic enamel paint complete all as specified. Note : (I) Refixing/welding of rolling shutters duly repaired/overhauled/welded/painted shall be included in the quoted rates of this item. (ii) Fixing of new parts of rolling shutters shall be included in the quoted rate of this item. (iii) Replacing of new parts of rolling shutters shall be paid and measured separately as supplying only under the relevent items. (iv) Makes/Size/Specifications of new parts of rolling shutters as per existing specification of rolling shutters. (v) Any damage or loss of rolling shutter during taking down/dismantling shall be made good by the contractor at his own cost.

Supply only safety lever locks and gear mild steel with 4 Levers for rolling shutters complete as per existing existing make

Supply only MS sheet 1.25mm thick for hood cover complete all as specified

Supply only curtain i.e interlocking lath sections formed from cold rolled steel strip 0.9mm thick complete all as specified

Supply only helical wire spring or flat spiral springs complete all as specified

Supply only ball bearing (ISI marked) size & make as per existing old type complete all as specified

Supply only MS 40mm bore pipes "heavy weight" for suspension shaft complete all as specified.

S&F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

S&F Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws complete all complete all as specified

S & F aluminium sections for doors, windows, ventilators, door partition including fabrication of frame and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame complete all as specified. Note : (i) Glass panes & handle will be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate.

Glazing with sheet glass 5.5 mm thick ordinary quality in panels of aluminium windows, ventilator, door etc. fixed with glazing clips, rubber beading and EDPM gasket in square not exceeding 0.5 Sqm in each pane.

Glazing with sheet glass 5.5 mm thick ordinary quality in panels of aluminium windows, ventilator, door etc. fixed with glazing clips, rubber beading and EDPM gasket in square exceeding 0.5 Sqm in each pane complete all as specified.

S & F mortice lock, vertical type, cast brass, 2 levers, vertical type, 100 mm size, finished smooth fixed in position complete all as specified and directed.

Taking down Aluminium door/window shutters area not exc 2sqm and refixing in the same opening including making petty repairs as required like cleaning and repair/replacement of beadings, glazing clips, rubber gasket, stoppers, adjusting tower bolts, locks, hydraulic door closer, hinges etc and make smooth functioning with entire satisfaction of Engr-in-Charge complete all as specified and as directed Note: Note: Replaced of any item shall be paid and measured seperately as Supply & Fix under respective item of BOQ

Taking down Aluminium door/window shutters area exc 2sqm but not exc 4 sqm and refixing in the same opening including making petty repairs as required incl cleaning and repair/replacement of beadings, glazing clips, stoppers, rubber beading, locks, stays, hinges etc and make smooth functioning with entire satisfaction of Engr-in-Charge complete all as specified and as directed Note: Note: Replaced of any item shall be paid and measured seperately as Supply & Fix under respective item of BOQ

S&F 150mm size floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and as directed.

S&F aluminium(extruded section body) door closer hydraulically regulated designation No. 3, universal type suitsble for door shutter of 851 to 1000mm in width and of weight between 61to 80 Kg all as specified. MAKE : Godrej or Equivalent.

S & F for pivot suitable for Aluminium shutter as per existing specfication including necessary fixing arrangments complete all as specified and as directed.

S & F for EPDM gasket complete all as specified and as directed.

S & F for rubber neoprene packing complete all as specified and as directed.

S & F for anodised aluminium snap on beading/tapper clip for fixing the glass or particle board complete all as spcified and as directed.

S & F for roller for sliding window complete all as spcified and as directed.

S & f for sliding star lock for sliding window complete all as spcified and as directed.

S & F for 150 mm stainless steel butt hinges complete all as specifed and as directed.

S&F in repairs double action floor door spring hydraulically regulated made of minimum 1.25mm thick aluminium alloy sheet foundation box main body of stainless steel cover, governing pivot made of brass, other parts amde of mild steel heavy duty and fixed for aluminium door all specified.

S&F for glow sign board for E/M installation cubical type of size 4ft x 2ft x 1/2ft made up of PGI sheet covered from all three sides and front side covered with poly sheet not less than 1mm thick of blue/white colour with letter writing with blue/white colour including providing 02 nos LED tube light of 18W each with all electric connections complete allas specified and directed by Engr-In-Charge. Note:- Matter to be written on glow sign board to be obtain from Engr-In-Charge before placing order for fabrication of board.

S&F for glow sign board for E/M installation cubical type of size 4.5ft x 2.5ft x 1/2ft made up of PGI sheet covered from all three sides and front side covered with poly sheet not less than 1mm thick of blue/white colour with letter writing with blue/white colour including providing 03 nos LED tube light of 18W each with all electric connections complete allas specified and directed by Engr-In-Charge. Note:- Matter to be written on glow sign board to be obtain from Engr-In-Charge before placing order for fabrication of board complete all as specified and as directed

S & F aluminium barrel tower bolts with barrel and bolt of extruded sections of aluminium alloys, 200 mm long, anodized finish not be less than Grade AC 10 of IS 1868 : 1996 with transparent anodic film complete all as specified and as directed.

S & F aluminium alloy sliding door bolts with hasp, staple and fixing clips of sheets, or extruded sections and fixing bolts and sliding bolts of extruded sections of aluminium alloy, 300 mm long, anodized to a bright natural, mat finish not be less than Grade AC 10 of IS 1868 : 1996 complete all as specified and as directed.

Supply and Fix, aluminium handles, Fabricated type, anodized, 150 mm size, complete all as specified and directed.

S & F 100 mm medium weight mild steel butt hinges made out of cold reduced low carbon steel or hot rolled carbon steel as per IS 1341: 1992 complete all as specified and as directed.

M & L for liquid soap container of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 105gms) complete all as specified and as directed.

Neetu Construction

NATIONAL CONSTRUCTION CO