Proposed Construction of Weigh Bridge and Operator Room with 1000 MT Godown at Panki Palamu, Jharkhand

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers. Not exceeding 150 mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing coarse clean sand in filling in in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labour, royalty and taxes all complete as per building specification and direction of E/I (Mode of measurement compacted volume)

Providing designation 75B brick work in C.M (1:6 ) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 125 mm thick reinforced designation 75A brick work in CM (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 25 including the cost of screening, carriage of materials, scaffolding , raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in Super Structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforcement designtion 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in supertructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including cost of screening materials scaffoliding raking out joints to 15mm depth curing taxesand royalty ( but excluding theb cost of reinforcement) all complete as per building specification and direction of E/I.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:1½:3 (1 Cement: 1½ coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size)

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level. 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for

Foundations, footings, bases of columns, etc. for mass concrete

Suspended floors, roofs, landings, balconies and access platform

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Weather shade, Chajjas, corbels etc., including edges

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one side teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resine of standard make with Aluminium fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non-decorative single leaf flush door shutter in door and windows with black board core blended with high quality phenol formal dehydes synthetic resine both side commercial veneered of standard make with oxidised iron fittings such as hinges, towerbolts, handle, cleat and sand blocks and taxes all complete as per building specification and direction of E/I.

providing Tor steel reinforcement of 8mm dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for SAIL & TATA STEEL)

providing Tor steel reinforcement of 10mm,12mm,& 16mm. dia bars as per approved design and drawing inclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

(a) 10mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)}

(b) 12mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

(c) 16mm (TMT coil Fe 500) (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

providing Tor steel reinforcement of 20mm,25mm, 28mm & 32mm. dia bars as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. 20/25mm TMT bar Fe 500 (only valid for Tata (Tiscon), SAIL, JSPL,Electrosteel Steels Ltd. Bokaro and Vizag (RINL)})

Supplying, fitting, and fixing M.S. Grill made of 20X6mm M.S. Flate as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per building specification and direction of E/I. (where materials is not supplied by the deptt.)

Supplying, fitting and fixing fully glazed steel door, window or ventilations of standard rolled 'Z' and mullion steel sections and size as per IS-1038 joints met and welded with 100X16X3mm M.S. lugs fixed in cement concrete (1:2:4) block 15X10X10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminimum beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 20mm dia M.S. Bar 1 meter long holding down bolt with nuts washers 100 X100 X6mm plate fitted and fixed with cement concrete (1:24) as per approved design all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing 50mm thick 2nd class patent stone flooring (1:2:4) with 20mm, to 6mm size graded stone chips finished with flooring coat of neat cement in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes and royality with all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622 / ISO 13006 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm .

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm cement plaster (1:4) in celling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5mm cement punning including curing, carriage of water with all leads and lift as per building specification and direction of E/I.

Providing 19mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including preparing the surface after cleaning removing dirt,scales grease including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing 250mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 250mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Providing 150mm. Wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of eartwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Water proofing for Old and New Roof Slab :- Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible

Covering of treated surface with PCC :- Providing 25 mm thick Cement Concrete M20(1:1.5:3) maintaining slope in alternate 2 mt x 2 mt panels with aaproved quality of stone chips of 20 mm

Providing and mixing Liquid Intergral water proofing compound in Conctrete or plaster as per manufacturer specification and as per direction of Eng - in Charge. Brand- Sika Plastocrate plus,

Providing and filling of 6 mm thickGroove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as per drawings and technical specifications and direction of E in Charge.(with 18% GST) , Brand :- Sika-Polysulphide, Fosroc- Thioflex 600, Dr. Fixit Pidiseal PS (42P) , MYK Seal PS or Euivalent

Extra for providing and placing in position 2 Nos 6 mm dia. M.S. bars at every third course of half brick masonry.

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:.3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Supplying and fixing rolling shutters of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters. : 80x1 .25 mm M.S. laths with 1.25 mm thick top cover

Providing and fixing ball bearing for rolling shutters.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer in-charge:Fixing with adjustable lugs with split end tail to each jamb

80x1.25 mm M.S. laths with 1.25 mm thick top cover

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. : In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. : M.S. tube

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement: 4 coarse sand): 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone/ sand stone slab.

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry@ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diameter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Coupler 75 mm

Coupler 110 mm Each

Single pushfit Coupler 75 mm

Single pushfit Coupler 110 mm

Single tee with door 75x75x75 mm

Single tee with door 110x110x110 mm

Single tee without door 75x75x75 mm

Single tee without door 110x110x110 mm

Bend 87.5° 75 mm bend

Bend 87.5° 110 mm bend

Shoe (Plain) 75 mm Shoe

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement: 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 32 mm dia

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Circular shape 450 mm dia

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply and all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge : 25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge External work

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931: 15 mm nominal bore

Providing and fixing PTMT grating of approved quality and colour. Circular type 125 mm nominal dia with 25 mm waste hole

Providing and fixing PTMT soap Dish Holder having length of 138 mm, breadth 102 mm, height of 75 mm with concealed fitting arrangements, weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour. 15 mm nominal bore, weighing not less than 32 gms

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe

Supplying and fixing C.I. cover without frame for manholes : 500 mm diaMeter C.I. cover (medium duty) the weight of the cover to be not less than 58 KG

Making soak pit 2.5 m diaMeter 3.0 Meter deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diaMeter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion :Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Providing and fixing male ended 1Smm dia brass bib cock of approved quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/I.

Provlding and fixing brass/C.l.Stop cock of approved quality all compelte as per specification and direction of E/I. BRASS STOP COCK : 15 mm dia

Providing and fixing G.M. non-return valve Horizontal/vertical type of approved qualilty as per specification and direction of Engineer -in-Charge. Horizontal non-return valve : 25mm dia weight not less than 375gms.

Engineer-in-Charge. Cutting chajja or cornice for laying G.l. pipe and restoring the same with R.C.C.(1:2:4) brick work in cement mortar (1:4) and cement plaster(1:4) as per specification and direction of Engineer-in-Charge.

Making holes in walls for laying G.l. pipes and restoring the same after pipe lavinq as per specification and direction of E/I. 250mm thick wall

Supplying, fitting and fixing vitreous white glazed earthen ware l.W.C.of parry Hindustan or any other l.S.S.approved make with 100mmH.C.l. 'p'trap lS litres C.l. pull and let go flushing cistern of namesor other l.S.S.equivalent make, complete with allfittings,C.l. or C.C.brackets 32mm alkathene/P.V.C. telescopic flush, pipe about 2 Mlong with one brass coupling and clamps G.l. chain and pull includingsupplying and fixing a pair of vitreous white glazed earthenware ware footrest to be fixed in floor 1Smm C.l. body brass spindle stopecock of weight not less than SOgrms, 15mm P.V.C. connection pipe450 mm. long and the exposed pipe and cistern with two coats ofapproved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) 580 mm.long (c) With 10lit. low level PVC cistern

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other l.S.S. approved make supported on painted C.l. or R.S. brackets 32mm C.l.brass waste, 15 mm dia C.l. body brass spindle stop cock of approved quality of weight not less than 350gams, 32mm PV.C. waste pipe 750mm long with brass coupling at one end and making plumber joint etc. all complete as per specification and direction of E/I.

Supplylng, fitting and fixing the following items complete with all materials as per specification and direction of E/I.

Glass shelf with C.P. brass rail. : 600x125mm glass shelf complete

Mirrors of 6mm thick plate glass bovelled edge mirror including : 450 mm x 300 mm size

C.P. brass towel rail 20mm x 600mm with bracket container

C.P. brass dish container medium quality with screw and hinges etc.

Earth work in excavation for laying of different types and sizes of R.C.C. spun pipes with disposal of excavated earth within initial lead and lift as per specification and direction of E/l. (i) For classification of soil item-A

Labour for laying, fitting and fixing NP2 R.C.C. spun pipe with collars in lines, level and grade and providing approved jointing materials and joints properly filled to make them leak, proof including providing sight rails bonning rod, night guard, Red Light and barrier etc. all complete as per specification and direction of E/I. 150mm dia R.C.C. spun pipe Upto 3.0 metre depth of invert below G.L.

Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600x450mm inter?nal dimension having 250mm wall thickness in cement mortar (1:6)including 12mm cement plaster (1:4) with punning on inside andcement plaster (1:6) with 600x475mm G.l. Cover with frame (weightnot less than 36k9.) alongwith earth work in excavation and 80 mmthick P.C.C. (1:3:6) in foundation and refilling all complete as per spe?cification and direction of E/|.

Circuit/ submain wiring in PVC conduit :-Wiring for circuit/ submain wiring along with earh wire with the followingsizes of FR PVC insulated copper conductor single core cable in surface /recessed PVC conduit as required

2x1.5 sq.urm+ 1x 1.5 sq.mm earth wire

2 x2.5 sq.mm + I x2.5 sq.mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Point wiring in PVC conduit, with modular type switch:- Wiring for light poinVfan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core in surface/recessed PVC conduit, with modular switch, modular plate suitable GI box etc as required : Group-C

Power plug widng in PVC conduit (2 x 4 sq. run) :- Wiring for light/power plug with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 No 4 sq.nrm FR PVC insulated copper conductor single core cable for loop earthing etc as required.

S/F PVC conduit :- Supplying and fixing of following sizes of PVC conduit along with accessories in surface / recess including cutting the wall and making good the same in case of recessed conduit as required.

S/F Modular type switch/ socket :- Supplying and fixing of following modular switch / soket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 amps, one way switch

5/6 amps, 3 pin socket outlet

S/F Modular type electronic fan regulator : Supplying and fixing stepped type electronic fan regulator on the existingmodular plate & switch box including connections but excluding modular plate etc. as required.

S/F Modular type blanking plate : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

S/F light plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in fronton surface of in recess, including providing and fixing 3 pin 5/6 ampsmodular socket outlet and 5/6 amps modular switch. corutection, paintingetc. as required (For light plugs to be used in non residential buildings)

S/F power plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fxing 6 pin 15/16 amps modular socket outlet and l5/16 amps modular switch. connection, painting etc. as required (For light plugs to be used in non residential buildings)

S/F ceiling rose :- supplying and fxing 2 pin 5 amp. Ceiling rose on the existing junction box/wooen block including connection etc. as required

S/F Batten holder : supplying and fixing Batten / Angle holder including connection etc as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F rewireable double pole/ TP&N switch disconnector : Providing and fixing following DP/TP&N sheet metal switch disconnector fuse unit in the existing metal board with rewireable type fuses, including drilling holes in metal board . making connections. etc. as required.

32 amps, double pole

100 amps, TP&N

S/F Busbar chamber : Providing and fixing following capacity busbar chamber with 4 strips of length 300mm made of copper suitable for following capacity complete with all accessories including connections, earthing the body etc. as required :100 amps

S/F S.P. MCB DB :- Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, compiete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) :

8 way, Double door

16 way, Double door

S/F 'C' series SP MCB: Supplying and fixing 6 amps to 32 amps rating, 240 volts, 10 kA, "C" curve, miniature circuit breaker suitable for.inductive load of following poles in the existing MCB DB complete with connections, esting and commissioning etc. as required.

6/32 amps, Single pole

40 amps, DP

Earthing with G.I. earth plate 600mm x 600mm x 6mm thick including accessories, and providing masonry enclosure with cover plate having Iocking arrangement and watering pipe etc. (with charcoal or coke and salt) as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable of l.l KV grade of size exceeding 95 sq mm but not exceeding 185 sq mm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required

Laying of one number additional PVC insulated and PVC sheathed/ XLPE power cable of 1.1 KV grade of size exceeding 35 sq mm but not exceeding 95 sq. mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable pf 1.1 KV grade of size not excecding 35 sq mm directr in ground including excavation , and refilling the trench etc as rquired, but excluding sand cushioning and protective covering.

Laying of one number PVC insulated and PVC sheathed/ XLPE power cable pf 1.1 KV grade of size not excecding 35 sq mm but not exceeding 95 sq mm direct in ground including excavation , and refilling the trench etc as rquired, but excluding sand cushioning and protective covering.

S.I.T.C of floowing rating LED Street lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage'1.00-270Y AC,50Hz. Luninarie shall be confirm to IS: 10322 part 5/section-3 and shall be complete with all neccssary accessories as required : 70/72W LED Street light

S.I.T.C of floowing rating LED Flood lighting luminarie with pressure die cast housing and toughened glass cover (IP 66 protection) in existing pole/pipe for supply voltage 100-270V AC,50Hz. Luminarie shall be confirm to lS:10322part-5/section-5 and shall be complete with all neccssary accessories as required

90/100W LED Flood light

150/160W LED Flood light

Supply Installation, testing and commissioning of follwing size ceiling fan 3 Blades confirming to13:374,.2019 including wiring the down rods of standard length (upto 30cm) with l.Ssq.mm. FR PVC insulated, copper wire suitable for 230V 50H2, single phase supply etc. complete as required

S.I.T.C of floowing rating surface mounted LED tube light fitting suitable for 230V 50H2, single phase supply etc. complete as required.-20/22W LED Tube light

S.I.T.C of following rating LED Post top lamp made in die cast aluminium housing with decorative clear/opal acrylic diffuser on existing pipe including connection with 1.5sq.mm. copper conductor etc all complete as required : 20/25W LED Post top lamp clear

Supplyind and making end termination with brass compression gland and Aluminium lugs for flowing size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required

3.5x50 sq.mm (35mm)

4x10 sq.mm (25mm)

3.5x25 sq.mm (28mm)

3.5x35 sq.mm (32mm)

3.5x70 sq.mm (38mm)

3.5x150 sq.mm (50mm)

Excavation in Soil using Hydraulic Excavator and Tippers with Disposal upto 1000 metres. Excavation for road work in soil with hydraulic excavator including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and tranporting to the embankment location within all lifts and lead upto 1000 m

Construction of granular sub-base by providing close graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with front end loader at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. Rate per CUM for grading-II Material

Dry Lean Cement Concrete Sub- base Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.

Cement Concrete Pavement Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with approve grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

Supplying of PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including 1100 volts. (Conforms to IS:1554,part-1):25 sq. mm,3.5 core

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1) :35 sq. mm,3.5 core

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1) : 50 sq. mm,3.5 core

Supply & laying of following PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. ( Confirm to IS: 1554, part-1). 70 sq. mm,3.5 core

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1) : 150 sq. mm,3.5 core

PVC/XLPE insulated PVC sheathed heavy duty, armoured electrical cable with aluminiumconductor forworking voltage up to and including L100 volts. (Conformsto IS:1554,part-1) : 10 sq. mm,2 core

7 Mtr. height Octagonal Hot - Dip galvanized pole( BOP - 7030) with top dia 70 mm, bottom dia 130 mm & made of 3 mm thick sheet, base plate dimensions200X 200X12mm ( Lx B xT) including suitable sizes of foundation bolt all complete as reqd. (Without Arm)

0.5m Single Arm suitbale for 70mm Top

Supply of Exhaust metal Fan 300mm(12"): Supply and fitting of 300mm(12"), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required

LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required.

lnstallation, Testing & Commissioning of the 7 Mtr. Octagonal Pole & light fitting with the help of suitable tools and plants, and construction of shallow foundation with M25 grade concrete considering safe soil bearing capacity of 10T/mhs sq. but excluding wire and MCB

Supply of 12mtr. High mast in one section Construction 5355 grade as per BIEN 10 025 Top Dia 100mm, bottom dia 360mm, plate thickness 3mm, 12side polygon, galvanisation as per BS EN ISO 1461, base plate dia 520mm, base plate thickness 25mm, GI single spike Ughting protection, maximum wind speed 47m/ s as per IS : 875 (Part-III) with 6 nos foundation bols of PCD r145mm TS 600/ 24mm dia/850 mm long. Luminaries carriage : Material for 40 NB ERW Class B - M.S. Pipe, dia of carriage ring 450mm (ID) with 8 arm, welded,2 sections having carrying capacity upto S luminaries. Trailing Cable : 5 core 2.5sq.mm. PVC flexible copper conductor Winch/Power Tool : Double drum, SWL 350 Itg with 0.75HP 6 pole single speed integral motor Rope : Grade AISI 1304,7 /19 construction, dia 5mm, BLC 1450 x 2 having 2 nos of continues lrope. Aviation obstruction light: twin dome aviation obstruction lights It CO typu as required. (But excluding Feeder Pillar)

For 12 mtr. High mast : ITC of the high mast and light fixture with the help of suitable tools and plants, wiring of luminaries with all wiring material like PVC insulated PVC sheathed flexible cable of suitable copper conductor lugs, MCB and all labour & construction of shallow foundation with M25 grade concrete for the high mast considering safe soil bearing capacity of 10T / mtrs sq. for 12 M High mast.

twin dome avivation light for highmast.

3 core PVC insulated PVC sheathed copper conductor flat submersible cable. Supplying , Flat flexible submersible cable with ,copper conductor , PVC insulated and PVC sheathed as IS:7098 3 Core 4 Sq mm. Copper wire

Supply fitting and fixing GI pipe 50 mm Dia (TATA or equivalent make) Medium Quaility as per IS:1239 ( part 01 ) 2004

Cost of Driling 200mm x 165mm x 125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

Supplying submersible pump sets confirming to IS 8034 and motor confirming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415V + 10%, 3PH, 50 Hz, A.C. supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for direct coupling. Pump shall have suitable outlet as Meteranufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 Meter submersible copper conductor cable in single/double run shall be provided with Each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 2 HP

Supplying Full automatic star selta starter to operate induction motor working on 415v 3phase 50hz with no coil. Over load element , On _OFF push buttom with necessary materials and connection to Supply etc complete starter with original sheel steel encloser as per 3914. F.A.S.D starter

Outdoor Feeder Panel ( for street light):Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of suitable size ,earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. All inter connections shall be made with 2.5, 4 Sq mm PVC Cu. wire. The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs Incomer : 1 No. 63A/FP/10kA/ MCB . 0-24hrs Timer switch with bypass arrangement, 40A duty contactor Outgoings: MCB 40 A, TPN, 10kA-1 no for highmast and MCB 20 A, TPN, 10kA - 6 nos for street light and bollards

New LT Panel : Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomers and outgoing of LT panel of 14 SWG CRCA Sheet (2mm) steel IP-54 floor mounting cubical type LT Panel suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 35kA. Size as per trequirement with front operated construction including seperate fabrication arrangement for fixing of switchgears and meters. The sheet steel under go minimum seven tanks treatement followed by finishing poder coating of minimum 60 microns thickness duly compart mentalized with locking arrangement duly fixed on base channel of suitable size having accessories mounted inside cubicale panel, earthing with 2 Nos. of earth studs. All opening shall be covered by soft rubber gaskit,enclosure shall be galvanished. Panel shall have suitable cable entry from top and bottom and suitable arrangement for multiruns aluminium cables for MCCB. The Panel includes 415V, 160A , 3 ph, 35kA , 50Hz Electrolytic aluminium bus bar( E91EWP) , earth bus with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing feeders complete in all respects. All inter connections shall be made with 2.5, 4, 6, 10 sq. mm PVC cu wire. The above panel consting of the following: Incomings 160A , FP MCCB( 35kA) as incomer 1 no-63A , FP MCCB(25kA) for DG incomer Electro-mechnical lock for auto changeover -1 set: 63A, 4P Outgoings 1 no-100A , FP MCCB(16kA) for godowan 2 nos-63A , FP MCB(10kA) for feeder pillars, spare

Carriage of materials from source to site work including loading & unloading all complete job as per specification and direction of E/I

Aggregate

Stone Metal

Brick

Fly Ash Brick

Non -Scheduled item Design, supply, fabrication, transportation, and installation of truss-less self-supported arch roofing system over the specified warehouse structure. All materials, consumables, labor, tools, machinery, and incidental items shall be included in the quoted price. ________________________________________ 1. Site Details: • Project Type: Warehouse Roofing • Span (Clear): ± 21.80 meters • Arch Rise: 3.00 meters (Span/5) • Length of Shed: ± 46.50 meters • No. of Bays: 1 • Eave Height: 5.60 meters (approx.) ________________________________________ 2. Roofing System Requirements: • Type: Truss-less (Self-supported Arch Type) Roofing System • Design: To be structurally stable without any intermediate truss or support, suitable for clear span of 21.80 meters and arch rise of 3.00 meters • Roof Coverage Area: Approx. 1,013.7 sq.m (21.80 m × 46.50 m) ________________________________________ 3. Material Specifications: • Sheet Material: Color Coated Colorbond® Zincalume® Steel • Coating Type: AZ150 (Al-Zn Alloy Coating, 150 g/m² total on both sides) • Standard Compliance: ASTM A 792 • Base Metal Thickness (BMT): 1.10 mm • Total Coated Thickness (TCT): 1.075 mm • Width of Coil: 912 mm to 1010 mm • Tolerance: ±2 mm ________________________________________ 4. Additional Requirements: • Installation: Complete laying and fixing of roofing with overlaps and arching to specified dimensions using hydraulically operated mobile forming machinery. • Fasteners: High tensile, corrosion-resistant self-drilling screws with EPDM washers to be used as per manufacturer recommendations. • Sealants/Consumables: All sealants, fasteners, insulation pads, edge closures, etc., required to ensure weather-tight performance shall be included. • Workmanship: Roofing system shall be free from dents, scratches, warping. Finish should be smooth and uniform in color. • Drainage/Gutters: (Specify if required) ________________________________________ 5. Design & Load Considerations: • Wind Load: As per IS 875 Part 3 (latest revision) • Live Load & Dead Load: As per IS 875 Part 2 • Seismic Consideration: As applicable per IS 1893 • Deflection Limits: As per IS 800 ________________________________________ 6. Quality Control & Inspection: • All material to be accompanied by manufacturer's test certificates. • The roofing system shall be inspected and approved before and after installation by the Engineer-in-Charge. ________________________________________ 7. Warranty: • Minimum 10 years warranty on material for corrosion resistance and color stability.

Supplying & installation of Single Turbo Ventilators 2300 CFM, Size 24", Aluminum Construction with Skylight of 2MM Thick Size 2 X 07 Ft. - with complete fixing Accessories

Supplying & installation of Hangers / Clamps (For Light hanging purpose).All materials, consumables, labor, tools, machinery, and incidental items shall be included in the quoted price.

Supply, installation, testing & commissioning of WEIGHBRIDGE. Platform Size 12.0 X 3.0 Meter Max. Capacity 60 Mt. Type of Platform Fully Welded Modular Type Weighbridge Main U-Beam 300 mm X 140 mm - U Beam (E – 350 Grade H T Plate) Cross Support 16 mm Thick Plate Between Two Main Long Beam Top Plate 8 mm Top Plate with anti-skid strips Foundation Frame 100 mm X 50 mm Long Frame with Fully Welded 350 mm X 350 mm X 16 mm Plane Plate Border Frame 100 mm X 50 mm - Both Side Heavy Duty Frame with Side Wall Mounting Load Cells MS Plates 150 mm X 150 mm X 16 mm - Load Cell Top & Bottom Plate Joint & Assembly Main Beam, Cross Support & Top Plate completely welded to each other. Guide Rail Round Pipe Based Side Frame - Ø 100 mm - Both Side Fasteners As per Required & IS Standard Paint 2 coat of ant-corrosive primer And 2 Coat Enamel Paint Material All Material will be IS 2062 Standard MATERIAL LIST WEIGHBRIDGE PLATFORM STRUCTURE- - 01 No. U-Beam Type modular Orthotropic • All Material will be IS 2062 Grade • Painting : 2 Coat Primer with Enamel Paint • All Standard Joint Assembly, Nut & Bolts, Foundation Plates etc…. • European design U beam orthotropic design. • Virgin material branded MOC • Value engineering modular design. HEAVY-DUTY LOAD CELL -06 Nos. • EAGLE –Multi Ended Share Beam Type Load Cell-34.5T each... • Pre-Calibrated Digital Technology (No Need to Make Calibrate Scale) • Digital signal for long distance. • Special diagnostic feature • Unique data string, can not be copy or replace. • In built lighting protection. • Inbuilt filters for noise reduction. • Load Cell Mounting Assembly with inbuilt Lightning & Surge Protection. • Suitable for sending signal over long distance. ELECTRONICS DIGITIZER (SMART INTELLIGENT TERMINAL SYSTEM) -01 No. • No Need to Use Computer System for our Smart Terminal • Direct Connect Dot-Matrix / Laser* Printer • Full Graphical LCD Display (130 X 40 mm). • Three step software calibration & smart calibration to correct small errors & accurate readings. • Inbuilt 200000 ~ 250000 Memories Storage Facility. • USB Port for Data Entry and Back Up. • USB Interface facility for Data Backup in External Memory Stick (Pen Drive). • Vehicle vise data entry and report printing • Multi Level Password for security - Dynamic (OTP System) & Regular Password Facility. • All Date entry show in single window • External SMPS Power Supply for Load Cell & Other System Safety. • Auto SMS Facility. • Optional facility to send SMS & email weighment records. JUNCTION BOX (SUMMATION BOX) -01 No. • High Protection Junction Box with GD Tubes & Built in Surge & Lightning Protection • Water Proof Cable PG-9 Gland (IP67 Protected) External Metal Box with Locking Facility for Extra Load Cell Cable & Junction Box - 01 No. USB – Key Board for Weighment Data Entry - 01 No. UPS With Battery - 01 No. Pc System - 01 No. Laser Printer - 01 No. CI test weight - 01 Ton. Jumbo Display – 50 MM - 01 No. E – Soft -Weighbridge Management Software - 01 No. LOAD CELL CABLE (SHIELDED) -Junction Box To Digitizer 100 Meter ACCESSORIES (CABLE, CONNECTORS & DATA SIGNAL CABLE ETC….) - 01 Set. • Flexible Conduct Pipe 1 Meter for Each Load Cell (Rat Protection) • Power Cable for Digitizer • RS 232 Interfacing Cable - 2 Meter (Communication with PC)

Supply, installation, testing and commissioning of RS PRO Square Wall Mounted, Window Mounted Extractor Fan, 190L/s, 50dB, External 2 Speed Reversible On/Off Control

Supply, installation, testing and commissioning of energy saving long life corrosion resistant , Vertical mounted pressure die-cast aluminium housing well glass luminairies with high power LED as light source.

Supply, fitting, fixing and commissioning of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 11kV grade.

Supply, fitting, fixing, commissioning and testing of Solar LED Standalone Street Light( 45W LED) with low maintenance lead acid battery for 3 day backup: A LED based solar street lighting system consisting of PV modules, electronics ,lead acid battery, and LED based luminaries all suitably mounted on a 6.0m tubular pole above ground , base plate etc as required included . The battery of 160(2x80Ah) is charged by electricty generated through the PV module panel (200 i.e 100x2 )during day time and the luminaries provides light from dusk to dawn. Specification of of solar LED Standalone street Light: Poly crystalline silicon solar panels, High lumen LED for max. efficiency with lifetime> 50,000 hrs CRI nominal 70. Pressure die cast aluminium IP66 enclosure. Controller to charge batteries & microcontroller for autonomously determination of sunrise & sunset. Specific deep discharge batteries are used to store the energy. Metal battery box to be fitted at 3.0m height.

Add 18 % GST

Add 1% Labour Cess

M/S A S CONSTRUCTION (BID ID -694796)

FASTCON INDIA PRIVATE LIMITED (BID ID -695670)

M/S S.A.CONSTRUCTION (BID ID -695557)

JAPHAR ALAM (BID ID -695558)

M/S AVINASH KUMAR (BID ID -695606)

M/s R.K. ENTERPRISES (BID ID -695524)

M/s S.S. CONSTRUCTION (BID ID -695735)