Repair/Renovation of Special Bungalow No. 10 at Gandhi Nagar Jammu. CNO- 598 NP

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles 10 mm to 25 mm

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed

Providing and laying in position Cement Concrete of specified grade excluding the cost of centring and shuttering, all work upto plinth level (1:4:8) 1 cement:4 coarse sand:8 graded stone aggreagate 40mm nominal size (crusher)

Providing and laying in position Cement Concrete of specified grade excluding the cost of centring and shuttering, all work ypto plinth level (1:3:6) 1 cement:3 coarse sand:6 graded stone aggreagate 20mm nominal size (crusher)

Providing and laying in position Cement Concrete of specified grade excluding the cost of centring and shuttering, all work ypto plinth level (1:2:4) 1 cement:2 coarse sand:4 graded stone aggreagate 20mm nominal size (crusher)

Brick work with common burnt clay F.P.S (non modular) bricks of class designation 75 in cement mortar 1:6(1 cement : 6 fine sand). Foundation and plinth and super structure upto floor V level.

extra for Brick masonry in superstructure above plinth level upto floor V level.

Half brick masonry with common burnt clay (non-modular) bricks of class designation 7.5 in foundations and plinth including curing in : 6.15.2 Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Extra for half Brick masonry in superstructure above plinth level upto floor V level.

15mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 fine sand)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 2mm thick

1mm thick

Finishing walls with Acrylic smooth exterior paint of required shade: Old work (two or more coats applied @ 1.67 liters/10sqm on existing cement paint surface)

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ liter, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface

Apply priming coat With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized iron/steel works

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):sal wood

Providing and fixing plain jaffri of 35x10 mm laths placed 35 mm apart (frames to be paid separately) including fixing 50x12 mm beading complete with :

"Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (Khajaria, Somany)"

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown (Khajaria, Somany double charged)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete Size of tile 600x600 mm

labour for shifting of debries /mulba from roof ,stairs momties etc and adjoining area of blocks to the dumping sites by engaging labours and other miscellenous works

Mason Ist class

carpenter helper

Engaging welder including the cost of welding set and helper for mislaneous welding works at site

Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-incharge. (Note: -Butt hinges and necessary screws shall be paid separately).Second class Deodar- wood : 30mm thick

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick. 12 mm thick Marine plywood conforming to IS: 710

4 mm thick glass pane (weighing not less than 10 kg/sqm)

providing and fixing glazed shutter for doors,windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S pressed butt hinges finished of required size with necessary screws 30 mm second class deodar wood

Providing and fixing wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge :Second class deodar wood : 30mm thick

Extra for using stainless steel grade 304 wire gauge with wire of dia. 0.5 mm instead of Galvanized M.S. Wire gauge with wire of dia. 0.63 mm for doors, windows and clerestory windows with necessary screws: (shutter area to be measured

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete 300x10 mm

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete : 9.98.1 300x16 mm

proving &fixing ISI marked almunium hanging floor door stoper ,ISI marked andized with neceesay screw etc complete single rubber stopper

Renewing glass panes, with wooden fillets wherever necessary : Float glass panes of thickness 4.0 mm (weight not less than 10kg/sqm)

providing &fixing of PVC Pipes for drainage severage,rain water flow pipe etc including labour &material costs complete job in all heights(LMR) 4' dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc. 15mm nominal dia pipes

20mm nominal dia pipes

25mm nominal dia pipes

providing and fixing of PVC panelling on walls /false ceiling 8 to 10 mm thick inc, all fitting and fixtures complete (wall affair or any equvl. Make.

providing and fixing wall paper or required colour shade and design of standard make as directed by the EIC

providing and laying water proofing treatment on roofs of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying (a)after surface preparation ,frst layer of cement @0.488 kg/sqm mixed with water proofing cement compound @0.253kg/sqm(b)laying second layer of fibre glass cloth when the first layer is still green .Overlps of joints of fiber cloth should not be less than 10cm.(c)third layer of 1.5mm thickness consisting of slurry of cement @1.289kg/sqm mixed with water proofing cement compound @0.670kg/sqmand coarse sand @1.289kg/sqm. this will be allowed to air cure for 4 hours following by water curing for 48 hours .the entire treatment will be upto 30cm on parapet wall and tucked into groove in parapet all around

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead 14.1.1 With cement mortar 1:4 (1 cement : 4 fine sand)

Providing and fixing of CP Brass short nose bib cock of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass long nose bib cock of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

Providing and fixing of CP Brass angle valve of approved make / specification as directed by E.I.C (Cera, Jaquar, Hindware or equivalent )

providing and fixing of wall bend mixer/ Sink Mixer of jaquar, cera or essco

Providing and fixing of central hole basin mixer of jaquar, cera or essco

Providing and fixing of Single Towel Rail 600mm of jaquar, cera or essco

Providing and fixing of Towel Ring Square of jaquar, cera or essco

Providing and fixing of Shower with arm of jaquar, cera or essco

Providing and fixing of Hand shower of jaquar, cera or essco

Providing and fixing of Hand Faucet of jaquar, cera or essco

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing Rectangular shape 453x357 mm

Providing and fixing soap dish

Providing and fixing toilet paper holder C.P. brass

Providing and fixing floor mounted, white vitreous china single piece,one piece seat of approved make with complete job as per direction of EIC

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C.flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required.White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Flat back wash basin size 450x300 mm with single 15 mm C.P. brass pillar tap

Providing and fixing white viterous china pedestal wash basin completely recessed at the back for the reception of pipes and fittings18.9

Providing, fixing and applying Plaster of Paris (POP) false ceiling consisting of frame work made with 50mm sq M.S. tubes of 18 G thickness as main runner at 600 mm c/c both ways, suspended/ supported with M.S. flats 25x4 mm from existing R.C.C. slab, finished smooth to line and level including necessary supports, scaffolding etc. as required and also including applying a coat of red oxide zinc chromate primer over the M.S. frame work and suspenders complete.ncluding providing and fixing minimum 10 mm thick POP (calcium sulphate semi hydrate variety) jute reinforced tiles of 600 mm x 600 mm of plain or of approved design.

Providing and fixing aluminum die cast body tubular type universal hydraulic door closer (having brand logo with IS: 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete :

providing and fixing nickel plated m.s pipe curtain rods ,with nickel plated brackets including fittings 25mm dia

p/fixing of flush door of approved make fixed with 1mm mica on both side including all fiiting and locks complete Job.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade, one or more coats on old work.

Providing and fixing precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

"Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works detail: "

Chequerred precast cement concrete tiles 22mm thick in footpath and courtyard, jointed with neat cement slurry mixed with pigment to matchthe shade of the tiles, including rubbing, cleaning and curing completeon 20 mm thick bed of cement mortar 1:4 ( 1 cement : 4 coarse,dark shade using ordinary cement

providing &fixing of ply 19mm thick ply including cutting wasteage fevicol carriage etc c LMR

providing and fixing of 1mm thick sunmica including cutting ,wastage,fevicols nails etc.complete (LMR

providing and fixing of 0.85mm thick sunmica including cutting ,wastage,fevicols nails etc.complete (green,amulya,vigro) LMR

Providing and fixing of 4mm thick ACP sheet incl. all required complete job as directed by EIC

Providing and fixing gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels Arer of slab over 0.5 sqm

Providing edge moulding to 18 mm/16 mm thick marble stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite Work

SS Handels 12''

SS handels 8''

SS Handels 6"

SS Hinges 3''

SS Hinges 4''

mortice latch and lock

Providing and fixing stainless steel A ISI 304(18/8) kitchen sink as per I.S 13983 with C.I brackets and stainless steel plug 40mm, including painting of fittings and brackets, cutting and making good the walls wherever required: Kitchen sink without drain board 610x460mm bowl depth 200mm

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. 125 mm

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete. 150x10 mm

Providing and fixing of modular kitchen accessorles of of approved specification incl carriage and fixing complete. SS Multi purpose basket 15''x20''x4''

SS Multi purpose basket 15''20''x6''

SS Multi purpose basket 15''x20''x8''

SS Multi purpose basket 15''x20''x12''

SS masnal pullout 15''x18''x18''

SS Cuttlery basket 15''x20''x4''

SS Thali basket 15''x20''x18''

P/F OF EDGE TAPE OF APPROVED MAKE AS DIRECTED BY EIC

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement concrete 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both sides with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete 20.17.1 For pipes 100 to 250 mm diameter

providing and fixing SLIDING CHANNEL 20''

providing and fixing auto hinges

providing and fixing hydraulic hinges

Providing / fixing polycorbonate sheet including wastage of 5 mm thick complete job

Supply, installation, Commissioning and Testing of Auto on/off Pressure Pump 1HP CG Tank 24 ltr of approved Make (Crompton/ kirloskar/servo/ Havells) and specification as approved by Engineer in charge incl all fixtures/fittings complete Job

Engage Trolley for shifting of mulba from site to outer area of municipality

Please Enable Macros to View BoQ information