SPECIAL REPAIR TO BUILDING NO.P-17,NP-20 AND TN-62 AT C HILL AND NAGROTA UNDER AGE B/R-I OF GE NAGROTA

Amount

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.50 sqm each and removing from site.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exc 1.50 sqm eachand n exc 4 sqm and removing from site.

Taking down shutter of any description area exc. 1 Sqm and n.exc. 2 Sqm and removing from site.

Demolition of brick work built in cement mortar including all quions, arches, pillars etc but excluding ashlar facings dressed stone work and precast concrete articles.

Demolition of cement concrete (unreinforced) in ground floors and paving not exc 15cm thickness.

Demolition of cement concrete (unreinforced) of any description and any position not other wise specifically provided.

Demolition of cement concrete (Reinforced) of any description and any position not other wise specifically provided reinforcement cut as required to facilitate demoltion.

Pressed steel frames of size 125 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete.

Pressed steel frames of size 105 mm X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including two coats of synthetic enamel paint over one coat of red oxide complete.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain PVC sheets for top rail lock rail and bottom rail on either side and as gap insert for top rail and bottom rail penelling of plain colour PVC sheetto be fitted in the MS frame welded/sealed to the styles and rails with suitablePVC sheet beading and joined together with solvent cement, suppling and fixing in the frame at site as per specification and drawings.

Supply and fix for PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube complete all as specified and as directed.

S&F 2nd class hard wood, 35 mm thick , flush shutter solid core construction with block board core and plywood both side face decorative panels for vision panels or peephole sqaure or rectangular includinf lipping (Glass measured and paid saparately) other fitting included like Mortice lock etc fitted to chowkhets.

35mm thick 2nd class hard wood glazed and skelton shutter open rebated and prepared to receive glass ,gauge etc ( without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8 clause 8.20(a), supplied and fitted to chowkats.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm dia and fixed with tinned tacks or galvanised mild steel staples

Sheet glass 3.00mm thick ordinary quality and glazing with oil putty pin head type glass.

Pin headed glass 3.00mm thick ordinary quality and glazing with oil putty pin head type glass.

M&L for PCC 1:2:4 type B-1 (20mm graded aggregate ) 25mm thick as in Sub base floor

M & L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 15mm thick screed bed in cement mortar 1:4 complete including dismantaling /demolation/Taking down Note:- Rates also includes in this item for necessary raking,circular cutting or notching and waste on tiles

M & L for Glazed ceramic colored tiles 300mmx450mmx 6 to 7mm thick,as in patches in vertical surfaces such as dado, skirting, wall etc set & jointed in neat cement slurry and pointed with coloured cement to match with tiles in over and including 10mm thick cement plaster in cement mortar 1:4. including dismantaling/demolation/Taking down Note:- Rates also includes in this item for necessary raking, circular cutting or notching and waste on tiles

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutter with frame, partly glazed with 5 mm thick tinted glass and partly panelled with 9 mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150 mm size, aluminium barrel tower bolt 200 mm size etc including taking down or and making good of disturbed surface all as specified below complete all as specified and directed. (a) Frame (top & side) section shall of size 101.60 x 44.75 x 2.4 mm ( Section No 14021) (b) Vertical Members of shutter Section shall be be of size 85.00 x 44.45 x 2.00 mm (Section No 19560) (c) Top Members of shutter Section shall be be of size 83.50 x 44.45 x 2.00 mm (Section No 19581) (d) Lock rail (Middle member) of shutter Section shall be be of size 150.00 x 44.45 x 3.00 mm (Section No 19596) (e) Bottom Members of shutter Section shall be be of size 150.00 x 44.45 x 3.10 mm (Section No 19584) (f) Glazing clip for securing glass of shutters shall be be of 0.80 mm thick (Section No 19370).Make- Jinal Section,

S&F Double action floor spring hydraulically regulated made up of stainless steel foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty suitable for toughen glass shutters complete. Make:- ENOX (Cat No FH-ECO-842) or similar type hardware fitting of make GODREJ / DORMA / OZONE

S&F aluminium anodised grill 6m thick fixed to aluminium window with and including 'H' type aluminium frames of size 34mm x 11mm complete all as specified and as directed.

M&L for Aluminium anodied (powder coated) window and ventilator shutters, side hung type, without sash bars, aluminium section weighing not less than 0.55 Kg/Metre including clips, rubber packing aluminium snap beading, screws, fittings (each shutters) such as peg stays 150 mm long, hinge type B-21 100 mm long (2 Nos), 150mm long D type handle (one number) and tower bolt 150mm long (one number) (Notes : (i) Glass panels to windows/ventilator shall be measured and paid for separately under respective item of this schedule as supply only. (ii) Thickness of powder (polyster) coating shall not be less than 50 Micron. (iii) Shade/tint of powder coating (epoxy polyster) shall be as approved by GE. (iv) Frame shall be measured and paid for separately under respective item of this schedule. (v) Quoted rate shall deem to included cost of alumiumum powder coated builder hard ware.

Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutter of 851 to 1000mm in width & of weight between 61 to 81 kg

S&F 100mm cast brass with mild steel bright polished type B-11 butt hinges, and fixed.

S&F 150mm long brass handle cast type polished handles and fitted.

MS 300 mm ordinary rat rails rod pattern door springs including roller and roller plate.

S& F Floor door stopper of aluminium alloy body and tongue ,anodised ,with hard drawn steel spring ,fixed in floor overall length of cover plate 140mm

S&F 300mm long brass sliding door bolt with sand and dry cast brass hasp staple bolt type and fixing bolt with rolled or drawn brass bolts and fixed complete.

S&F 150mm long Brass skeleton tower bolts with cast brass plate and staple and rolled or drawn brass bolts and fixed.

S&F 18/19mm thick solid PVC board prelaminated one side and other side plain as in board/shelves/kitchen cabinate ( Board must be water proofing ,termite proof) .

Brick work with sub class “B” bricks straight or curved on plan exc 6M mean radius build in CM 1:6 using all as specified using old size bricks

Brick work with sub class “B” bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 using all as specified using old size bricks

Taking down cement plaster on brick or stone wall etc including racking out joints, hacking for key scrubbing down with water etc to receive new plaster etc.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:6 finished even and smooth without using extra cement all as specified ( internally)

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in CM 1:4 finished even and smooth without using extra cement with Water proffing compound all as specified (WPC measure and pais saperately)

M&L for Rendering 5 mm thick in CM (1:3) on ceiling finished even and smooth without using extra cement including two coat of white wash on ceiling including preparation of surface .

Supply only Liquid water proofing compound.

Taking down existing cement plaster of any description over damaged surfaces irregular facia, chajjas and in similar work and also for narrow width etc and rendering dubbing coat 15mm thick cement plaster in CM (1:4) over a coat of cement slurry @ 3.00 Kg/Sqm making surface even ( avg 50mm thick PCC 1:2:4 type B-1 using 20mm crushed stone aggregate shall be provided wherever required) followed by 05mm thick rendering in CM (1:3) finished complete all as specified and directed including two coats of cement base paint over a coat of primer over new plaster surface including preparation etc complete.(after curing of specified time and drying the surfaces as required).

Applying two coats of synthetic enamel paint over a coat of red oxide prime on new steel surfaces any description, not otherwise described over 10 cm width or girth including preparation of surfaces.

Applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surfaces of any description, not otherwise described over 10 cm width or girth including preparation of surfaces.

M&L for Complete removal of existing treatment applying two coats of oil bound distemper over a coat of wall putty 2 to 3mm thick on plasterd surfaces preparatory to distempering on wall surface .

M&L for Preparing newly plastered surfaces of walls and applying two coats of oil bound distemper over a coat of wall putty 2 to 3mm thick on plasterd surfaces preparatory to distempering on wall surface .

Preparation of old plastered surfces of wall and applying two coats of cement base paint over a coat of wall care putty 3mm thick

Preparation of newly plastered surfces of walls and applying two coats of Cement Base Paint over a coat of wall care putty 3mm thick complete all as spd and as directed

Three coat of white wash on newly plastered surface on wall including preparation of surface complete all as specified and directed.

Three coat of white wash on old surface on wall including preparation of surface complete all as specified and directed.

Preparation of newly plastered surfces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick

Preparation of Complete removal of existing trreatment preparing old plastered surfaces of Ceiling and applying two coats of oil bound distemper over a coat of wall care putty 3mm thick

M & L for dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by the Engineer-in-Charge

M&L for vitrified ceramic light shade tiles 10 mm thick (square/Rectagular) polished area exceedign 0.36 sqm and n exc 0.42 sqm in each tiles as in floors etc set and jointed in neat cement slurry and pointed in white coloured cement to match the shade of tile over and including 15mm thick screed bed in cement and sand mortar (1:4). Note :- Quoted rate shall deem to be included cost of screed bed. Note:- Before executing of Tiles work ATT Will be done and ATT will be measured and paid seperately

M & L for Non-Skid coloured printed ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles exceeding 0.18sqm and not exceeding .38 sqm of each tiles as in skirting / dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:4 for laying glazed tiles in floors etc. complete all as specified and as directed by the Engineer-in-Charge Note:- Before executing of Tiles work ATT Will be done and ATT will be measured and paid seperately

Dismantling of wall and ceiling boards( fibre,pulp,insulations etc) orinsulation boards/slabs/blankets any thickness including cover fillets all as directed

M & L for Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications.

M & L for 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

M&L for 18-20mm thick pre polished granite slab (with exposed edge duly grind and mirror polished) laid on Steps, kitchen platform top, window cill, steps, jambs and like set in neat cement slurry over and including15mm thick screed bed in CM 1:4, pointing in white cement with pigment to match the stone all as specified and directed by Engineer -in -Charge.

Labour only for moulding to granite stone/Kota stone in to bracket straight or circle to facing of squared granite of any description

PCC 1:3:6 C-1 (using 20mm graded crushed stone aggregate) as in plinth protection (75mm thick ) , sub base finished even and fair all as specified.

RCC 1:2:4 type B-1 ( using 20mm graded crushed stoneagg) as in chajjas, shelves ,coping,benching and similar items.

Providing 75mm thick precast reinforced cement concrete slab 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) and set in CM 1:4 . ( NOTE : (reinforcement shall be measured and paid for separately).

Form work to chajjas, shelves ,troughs and similar items including edges.

Form work to edges of concrete flats RCC/PCC band exc 5 cm but exc 10 cm. Fair finished

TMT bars 10mm dia and over cut to lengths bent to shape required including cranking bending and spirally hoping for columns hooking ends and binding with MS wire annealed n.less then 0.90mm dia.

All as per item No above but 6mm to 8mm dia -ditto-.

Providing number plate of size 450 x 300x20mm in CM 1:4 and writing building No of height 8 to 10cms with luminous paint through grooves of size 12 x 12mm ( Base: Black, grooves : orange)

S/F in repairs to rotational moulded vertical water storage tanks with closed tops ( cylinderical ) hoisted and fixed in position 1000 ltr capacity incl disconnecting and refixing the existing GI fitting and pipe complete all as directed.

Rotational moulded polyethene water storage tank 500 ltr capacity hoisted and fixed in position including PVC float valve 20 mm bore and including dismantling of existing water storage tank complete.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store upto 25mm bore.

15mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.

20mm bore GI tubing (medium grade) with all fittings and fixed complete to walls and ceiling or laid in floors/roofs.

Cuttings chases for concealed water tubing of concealed conduit (cutting n.exc 10 cms girth) and making good in CM ( 1:3) in brick walls.

Shower rose brass chrominium plated 125mm size complete all as specified and directed.

15mm bore fancy type bib tap brass CP (Long body) with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

15mm bore fancy type CP brass Mixer, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified and as directed.

S&F Cast copper alloy CP angle Valve fancy type screwed both ends for iron pipe 15mm dia/ bore of pipe

All as per item No above but with long shank and cup (concealed type)

Stop valves ,cast copper alloy ,screwed down high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for union 20mm dia

CP Pillar taps, 15mm fancy type cast copper alloy, with capstan heads, screwed down high pressure, without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

Soap dish with including chromium plated brass screws and wooden/plastic cleats ( Minimum weight 105gm).

Towel rail 600mm long of PTMT fixed with including chromium plated brass screws and wooden/plastic cleats ( Minimum weight 190gm).

Vitreous china squatting pan “ORISSA” pattern size 630x450mm ( Make : Hindware)white with integral foot rests all as fixed in repairs including cast iron ‘P’ or ‘S’ trap 100mm bore including PVC low level cistern of 10 litres capacity including brackets jointing to flush pipe, PVC connection (600x15mm), flushing pipe complete fixed in repair all as directed by Engr-in-Charge.

Vitreous china wash down closet pan (Pedestal pattern) white with ‘S’&'P' trap plastic seat cover white including connection to out going pipe & to flushing pipe, anti syphonage pipe etc complete all as specified and directed by Engineer-in-charge

S & F in repairs,PVC valve less symphonic action type, flushing cistern, low level, white of capacity 10 ltrs with inlet , ball valve, float and and fixing arrangement complete.

Dismantling cast-iron/PVC pipes including fittings taking out of trenches or walls as required dia of pipe upto 100mm.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 110mm bore.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls for 75mm bore.

S&F PVC (SWR) Bends any radius for 110mm bore.

S&F PVC (SWR) Bends any radius for 75mm bore with oval access door.

S&F PVC (SWR) Branch pieces single( Single Y) equal or unequal) for 110mm bore with oval access doors.

S&F PVC (SWR) Branch pieces single ( Single Y) equal or unequal for 75mm bore with oval access doors.

S&F PVC (SWR) vent cowl 75mm

Ditto as per item 90 above but 110mm

Vitreous china wash basin white flat back size 550 x 400mm incl waste pipe chain plugs and 32mm dia bore CP coupling complete as in repairs including a pair of bracket.

Shelf of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats (minimum weight 300 grams)

Surface excavation n.exc 30cm deep and avg 15 cm deep and getting out any type of soil.

M/L 75 thick mm Cement concrete Type C2 1:3:6 (using 40 mm graded stone aggregate) in sub base floorring

M&L PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in copings, plinth course, damp proof course, bed blocks, benching, PCC cills and similar items.

Plain cement concrete machine pressed, precast inter locking coloured,glazed (rubber moulded) paver blocks M-40 grade, any shape & size 80mm thick with grey cement & pigment laid over sand cushioning complete as directed.Note : Sand cushioning shall be measured and paid separately.

25 mm thick sand cushioning for interlocking paver blocks including spreading and consolidating complete all as specified and directed. Note: (i) Sand shall be coarse sand as specified. (ii) Punned down thickness shall be considered for measurement and payment.

PCC 1:4:8 D-2 (using 40mm graded crushed stone aggregate) as a sub base to chequred tile ( 75mm thick ) finished even and rough.

20mm thick screed or screed bedding in cement mortar 1:4 as a sub base to interlocking tile

Cement concrete interlocking pre-polished tiles glossy look machine pressed 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors complete all as specified and directed.

100mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)

75mm bore CI floor trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)

100mm bore CI Nahani trap with grating including jointing CI pipe in run lead, cutting holes in walls and making good surface in cement concrete surface type B-1 (1:2:4)

S&F in repairs 20 to 25mm external dia drapery rods stain less steel with incuding designer lattos and brackets all as specified and approved by Engr In charge including taking out old pelmet with curtain rods all as directed.

S&F in repairs Mortice lock 4 lever with handle complete set make godrej cart part No 172

Dismantling Plin or Corrugated steel sheeting, any guge, thickness in roof covering and removing from site of work complete all as specified

S& F 0.50mm thick Pre painted galvalume alluminium zinc coating GI based corrugated steel sheeting with colour having tensile strength 550Mpa as in roof covering /Cladding to wall fixed with self tapping screws as specified. and 15cm end lap fixed with'L' type or 'J' type hook bolt (08mm dia) complete all as specified and as directed of class VIII.

S& F 0.50mm thick Pre painted galvalume alluminium zinc coating GI based Plain steel sheeting with colour having tensile strength 550Mpa as in roof covering /Cladding to wall fixed with self tapping screws as specified. and 15cm end lap fixed with'L' type or 'J' type hook bolt (08mm dia) complete all as specified and as directed of class VIII.

M & L for Dismantling wrought iron or mild steel work of any description not otherwise provided all as specified and directed

Mild steel framed work such as grills,roof truss gratings etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders framed balusters, walk ways, railings, frame work of water tanks and similar work conforming to E-165 (Fe-290) complete all as specified and directed by Engineer-in-charge.

M & L, preparation of new or previously untreated surfaces with one coat of Red oxide and two coats of synthetic enamel of ordinary tint on surfaces of any description over 10 cm in width or grith, not otherwise described.

M & L for Toughned glass 10mm thick as in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes required.

Supply and fix aluminium anodised snap grid ceiling of frame size 600 x 600mm, main Tee section of size 36.5 mm x 25 mm x 1.4 mm thick, cross Tee section of size 23.5 mm x 26.4 mm x 1.4 mm thick, supported at ends all along the wall with aluminium anodised angle of size 40 mm x 25 mm x 2 mm thick and 4mm dia GI suspenders complete all as specified and directed.

100mm long butt hinges (medium weight) colled rolled mild steel fixed with welding.

MS butt hinges medium weight cold rolled of 50mm.

S & F Box type Steel windows with double shutters (inside for wiremesh & out side for glass), incl guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.

S & F Box type Steel ventilators top hung double shutters (inside for wiremesh & out side for glass), incl guard bar,hinges, steel handle, tower bolt and steel peg stay complete with glazing bar dovetailed or welded including a coat of red oxide after preparation of surface before fixing.

M&L for Machine cut kota stone flooring 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) (Each stone not less than 55 cms x 55 cms) over 15mm thick screed bed in CM ( 1:4) as in floor finished rough including roughening of existing surfaces by pick axicess and applying a coat of cement slurry @ 03 Kg/Sqm of surface.

M&L for Machine cut kota stone slab 20-25mm thick in skirting, dado and pillars, risers of steps laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing ( mirror finish) over 15 mm thick rendering in CM ( 1:4) including taking out of existing dado.

Non-skid coloured tiles 400x400x7mm thick as in floors set and jointed in neat cement slurry and pointed in coloured cement to match over 25mm thick PCC (1:2:4) type B1, over screed bed or beddding layer of CM 1:4, 15 mm thick complete all as specified and directed.

Taking down existing AC pipes any dia as in spouts etc and providing 110 mm bore PVC (SWR) pipes in short length as in spouts fixed with PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate.

Dismantling brick tiles or terracing tile, single layer on roof including cleaning the roof surface and filling the cracks with silicon compound if obsserved on roof

M&L for PCC 1:2:4 type B-0 (20mm graded aggregate ) 50mm thick as in padding finished even and smooth without using extra cement

M&L for Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm .

M&L for Laying APP (atatic polypropylene) modified membrane 3mm thick and weighing not less than 3 kg/sqm with 160 GSM/sqm, non woven polyester mat as center core reinforcement, laid with 75 mm side over lap and 100mm end over lap, the membrane has to be laid with LPG tourch and over lap sealed and finished neat over roof including a coat of bitumen 85/25 at the rate of 1.2 Kg per sqm over APP membrane.

M&L for Cement concrete tiles 25 cm x 25cm x20mm thick machine pressed set jointed and pointed in neat cement slurry on roof over APP membrane laid over 15mm thick cement screed bed in cement mortar 1:6

20mm thick screed or screed bedding in cement mortar 1:4 as a sub base to interlocking tile

Cement concrete interlocking pre-polished tiles glossy look machine pressed 30 cm x 30 cm x 25 mm thick, set, jointed and pointed in neat cement slurry (with grey cement and pigment) as in floors complete all as specified and directed.

S & F in repair 15 mm bore Brass CP Non Telephonic mixer for mixing hot & cold water screwed down for iron pipe

S&F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms complete all as specified.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floorof 75mm bore size.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or floorof 110mm bore size.

S&F Toilet paper holder chromium plated fixed as in repair complete all as specified and directed.

S&F aluminium handles 125mm cast type anodized.

M&L for Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces

Applying one coat of aluminium paint on top of APP membrane.

M&L chequered cement tiles concrete 20cm x20cm x 25mm thic, set jointed in neat cement slurry in floor including 15mm thick screed bed or bedding layer of mortar 1:4 for laying floor finishes etc all as specified. .

Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custedy for taking credit all as specified and as directed by Engr-in-Charge

Taking down ceiling fan any sweep, removing blades ,cleaning the fan completely for dust and dirt, oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engr-In-Charge.

Taking down exsisting LED based light fitting of any type, keeping aside safely & refixing the same to its original position after completion of point wiring, B/R work all as specified and directed by Engr-In-Charge. Note: If any part found unserviceable during the refixing of LED light fitting at site shall be provided by the contractor and cost for the same shall be deemed to be included in the quoted rates.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) PVC casing caping in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following;- (a) One light point controlled by one switch 5 Amp

(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp

(c) One socket out let 5Amp controlled by one switch on same board.

(d) One socket out let 5 Amp controlled by one switch on independent board.

(e) One bell point 5 Amp controlled by one bell push on independent board.

(f) One light point controlled by two, 2way switchs5 Amp

All as per item here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independat board.

All as per item here in before but point wiring with 4 sqmm FRLS multi stranded copper conductor cable for main circuit and 4 sqmm cable as earth continuity conductor for controlled by two pin and earth plug and socket complete with one single pole MCB 20 amp 240V

S & F Modular snap switch SP one way 5/6 Amps suitable for 1 Module complete all as specified.

S & F Modular Bell push ,SP 5/6 A suitable for 1 Module complete all as specified.

S & F Modular socket 5 pin 5/6 Amps suitable for 2 Module complete all as specified.

S & F Modular snap switch SP one way 15/16 Amps suitable for 1 Module complete all as specified

S & F Modular socket 5/6 pin 15/16 Amps suitable for 2 Module complete all as specified.

S & F Modular Fan step Regulator electronic, 120 watts 2 Module complete all as specified.

S & F Modular white cover plate incl Modular base frame/boxes & powder coated Modular sheet metal concealed box for 6 module complete all as specified.

All as per Item above but 3 module complete all as specified.

All as per Item above but 2 module complete all as specified.

All as per Item above but 8 module complete all as specified.

All as per Item above but 12 module complete all as specified.

S & F Modular blanking plates 1 module complete all as specified.

S&F of ceiling rose surface type 65mm x 50mm 2 to 3 terminal complete .

M&L Integrel sleek extruded batten aluminium /CRCA channel fitting with LED 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V 50 Hz. Cat part no.112181 BLRB-DB 118 ( for batten fitting) & Cat part no. BLRB18W CW (for LED 18 watt ) or equivalent in approved make.

S&F baton integrated LED channel of 5W, 230V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, Power Factor not less then 0.9 as per Cat No BCLSB 05 WH of Bajaj or techno commercial equivalent in approved make.

M&L LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz .

S&F decorative wall mounted luminaire with & including 9 Watt LED lamp complete as per Cat No of LHFHCHE1TL1W020 of Havells or equivalent in approved make.

S &F LED sleek surface round ceiling mounted decorative down light fitting with PC cover suitable for 1x12 watt as per Cat No BGSLO sleek surface 12 WH RD of Bajaj or equivalent in Havells / Polycab.

Supply and fixing in replacement of engaugement light red & green LED type built in PVC gang box complete including lamp all directed by Engr-in-Charge.

Supply and fixing swing type wall mounting fan 450 mm sweep single phase AC 230/240V complete for wall mounting incl grouting, holding down bolts, nuts, and provision of flexible copper conductor cable 3 core 23/0.0076 size from ceiling rose to fan. Make per model No Airboll Hi-speed of Havells and equivalent in Bajaj / CG.

Supply & fixing heavey duty PVC Exhaust fan 300 mm sweep single phase AC 230/240V complete with louvers Make : Havells/ Bajaj/CG

S&F Single pole & neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 amp 240V.

S&F MCB single pole 6 to 40 Amps 10 KA 230 volts "C" series complete

S&F MCB SPN 63 Amps 10 KA 230 volts "C" series complete

S&F MCB single pole 40 Amps 10 KA 230 volts "C" series complete

S&F MCCB 125A 4Pole 16KA 415 Volt with fixed magnetic and fixed thermal setting complete.

S&F sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete incl taking out existing UNSV DB with MCBs.

S&F sheet metal enclosure double door for distribution board factory made for MCB DB load link TPN 4 way suitable for MCCBas incomer, 125 Amp,4 pole. (when MCB's are to be used) with suitable size of busbar including 125 A MCCB as incomer 16 KA complete,fixed flush in wall including chases wall for fixing DB and making good the distributed wall surfaces to match with existing specification including taking down all as directed by Engr-in-Charge at site incl taking out of exsing UNSV DB with MCBs.

M&L for sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 20 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6.0 sq mm as earth continuity conductor connected to commen earth and earth dolly complete incl taking out existing UNSV service connections.

Sub main wiring with two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 25 mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sq mm as earth continuity conductor connected to commen earth and earth dolly complete .

S&F white powder coated CRCA housing with LEDs 36W, 230 V, 50 Hz Surface mounting LED 2 feet x 2 feet luminaries, Sweamless front frame with flat white hight transmission acrylic cover complete with all accessories including connecting up with twin core twisted flexible copper conductor cable with suitable size. Cat part no.BZSSQL 36W WH of Bajaj or equivalent in approved make.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 3 of MES SSR Part-I (2009) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete.

S&F switch piano flush type 5 Amps single pole one way complete,

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete.

S&F switch socket combination 2 in 1 5 pin 5 /15 Amps flush type complete.

S&F of ceiling rose surface type 65mm x 50mm 2 to 3 terminal complete .

S&F Step type fan regulator 300 watt, 230 volts, 50 HZ, AC. Supply complete .

S&F bell push piano type 5 Amps complete.

S&F electric bell ding dong 230 volt AC complete,

S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F for LED bulb 7 watt complete all as specified and directed.

S&F sheet metal enclosure distribution board SPN 12 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete.

S&F sheet metal enclosure distribution board SPN 04 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete.

S&F MCB single pole 6 to 32 Amps 10 KA 230 volts "C" series complete.

M&L for sub main wiring with four single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 6 Sq mm drawing through and including concealed rigid non metallic PVC conduit medium grade ISI marked 25 mm dia including two single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 4.0 sq mm as earth continuity conductor connected to commen earth and earth dolly complete .

S&F sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz double door with neutral, Earthing bar and din rail complete.

Supply in replacement, baton integrated LED channel of 5W, 230V frequency 50/60 Hz integral sleek extruded polycarbonate LED channel with white acrylic cover, Power Factor not less then 0.9 as per Cat No BCLSB 05 WH of of Bajaj / Havells / Crompton.

Supply and laying or fixing of cable 1100 volts grade cable PVC insulated aluminium conductor un-armoured of 16 Sqmm 2 core flat or circular, served with inner sheathing of pace tape and overall PVC sheathed in service connection suspended by insulated hangers not more than one Mtr apart including 4 mm dia suspension GI wire, complete all as specified and as directed by Engr-in-Charge.

U K Engineering Works

Kalsi Engineers and contractors

M/S Shankardass Devidass

BMMJ TRADERS AND ENGINEERS

J S ENGINEERS

Kanwal Nain Behl