Loading
Loading…
Loading…
Tender Value
₹85.1 L
EMD Value
₹1.7 L
Closing Date
12 Jun 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DRAWING
15 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover.
Electrical License: The tenderer shall possess a valid Electrical Contractor License, issued by any State Government or Union Territory Administration, authorizing execution of electrical works up to 650 V. The contractor shall have in his employment or shall engage a person holding a valid certificate of competency issued by any State Government or Union Territory Administration for supervision of electrical works up to 650 V. Offers not accompanied by a valid Electrical Contractor License and requisite Supervisor competency for works up to 650 V shall be summarily rejected. Note: In case of expiry of validity of license during contract, the contractor should renew the license so that it is always valid during contract
Technical Eligibility Criteria: (a) The tenderer must have successfully completed or substantially completed any of the following during last 07 (seven) years, ending last day of month before the one in which tender is invited: Three similar works costing not less than the amount equal to 30% of advertised value of the tender, or Two similar works costing not less than the amount equal to 40% of advertised value of the tender, or One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Definition of Similar nature of work:-Works of wiring/cabling or installation and commissioning of electrical items (other than on coaches) such as lights, fans, pumps, charging arrangements, earthing etc. (with or without supply of items / equipment) for 230V, 1phase or 415V, 3phase system or higher voltages".
9 conditions · 1 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Tenderer /s are required to submit a scanned / attested copy of following information along with their tender- 1. Bank Account No 2. Name of Bank 3. Indian Financial System Code {IFSC} 4.PAN No 5. Tenderers Contact No Contractor should provide firms PAN, issued by Income Tax Department with his quote or within30 {Thirty} days of award of contract. No payment will be released without submission of PAN. All taxes including surcharge and cess shall be recovered from his payment as per tax provisions in vogue.
The tenderer shall thoroughly go through the entire tender document and strictly adhere the instructions and directions given at different pages.
It is responsibility of the tenderer that they ensure to see any corrigendum of the tender to check the corrigendum on the website from time to time.
All the required/supporting documents should be scanned and uploaded.
In case the date of closing mentioned in the Notice Inviting Tender is declared a holiday/bandh/strike etc. on any account, the date of closing tender online will not be changed as the application in the website of IREPS does not permit submission of any offer after closing date and time of the tender. However, opening of tenders online will be on any convenient day after the closing date/time of tenders.
Opening of e-tender online:- The e-tenders will be opened online using the IREPS portal. No representative is required to be present for opening of tender and taking notes of rates quoted and ranking as the complete details of rates etc. of all the bidders shall be available to the bidders in the website after the opening of the tender.
Nanded Division-Construction of 32 bedded new running room at Chhatrapati Sambhajinagar (CPSN) Railway station. - Electrical Arrangements.
NED-E-01-2026-27
NED-E-01-2026-27
Open
Works - General
12 Months
Nanded, Maharashtra
₹0
₹1.7 L
12 Jun 2026
20 May 2026
29 May 2026
139 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 85,11,288 | ||
| — | 156.00 | — | — | ||
| Supply and fixing of 18 W LED round/square type slim light fittings conforming to specification. Make: Bajaj/Havells/Philips/Surya or similar | — | — | — | 2,09,352 | |
| — | 96.00 | — | — | ||
| Supply and fixing of 20 W LED Tube Light fittings conforming to specification Make: Havells/Syska/Crompton /Bajaj/Surya or similar | — | — | — | 37,344 | |
| — | 26.00 | — | — | ||
| Supply and fixing of Ventilating Fans(Exhaust fan) of 4 pole 300 mm sweep size with metallic body with capacitor conforming to IS No.2312/67 (Reaffirmed 2005) complete with louver and all connected accessories. Make: Havells/CG/Bajaj/Khaitan or similar | — | — | — | 59,280 | |
| — | 16.00 | — | — | ||
| Supply and fixing of 40 W LED type weatherproof street light fitting complete with all accessories and conforming to specification no. Make: Bajaj/Havells/ Philips or similar | — | — | — | 40,256 | |
| — | 60.00 | — | — | ||
| Supply and fixing of 3 W LED wall-mounted bedside reading lamp suitable to operate in 230 V, 50 Hz AC | — | — | — | 66,240 | |
| — | 8.00 | — | — | ||
| Supply and fixing of BEE 5Star rated electric storage water heater (Geyser) of 15Ltrs. Capacity suitable for operation on 230 Volts(+/-10%), single phase, 50Hz AC supply with all connected accessories complete. Make: Bajaj/Havells/Crompton or similar | — | — | — | 64,000 | |
| — | 27.00 | — | — | ||
| Supply and fixing of Decorative 0.5 W LED Night Lamp in approved manner with lamp holder | — | — | — | 2,430 | |
| — | 22.00 | — | — | ||
| Supply and fixing of wall/floor mounting type Voltage stabilizer of V-Guard VG 500 Voltage Stabilizer for AC up to 2 Ton (170 - 270 V) with all connected accessories and works. | — | — | — | 53,328 | |
| — | 22.00 | — | — | ||
| Supply, installation, testing and commissioning of BEE 5 Star Rated 1.5 Ton Inverter type Split Air Conditioning unit conforming to specifications attached and marking S. No. and date of erection. Make: Samsung/Blue star/Hitachi/LLOYD/LG/Voltas/Carrier /Mitsubishi/Daikin or similar | — | — | — | 8,78,680 | |
| — | 220.00 | — | — | ||
| Supply and Fixing extra Copper two pipes for Split AC (if required as per site condition and cost is for two pipes/meter) | — | — | — | 97,680 | |
| — | 220.00 | — | — | ||
| Supply and fixing of Drain pipe CPVC of 25mm dia including accessories, bend, elbows, tees, flanges, tapping's, wall sleeves, hangers supports anchors etc. | — | — | — | 5,940 | |
| — | 220.00 | — | — | ||
| Supply and fixing of 4corex2.5Sq.mm flexible copper cable (communication cabling)for Split/Cassette AC | — | — | — | 18,700 | |
| — | 22.00 | — | — | ||
| Supply, fixing of outdoor suitable outdoor stand for Split AC. | — | — | — | 14,300 | |
| — | 30.00 | — | — | ||
| Supply, fixing and connecting of Protected Power Unit for with Built-in 16-25A MCB (as per requirement) conforming toIS:13032 & IS:8623 with suitable sheet steel enclosure with socket and all connected accessories complete. includes cutting of wall/beam and duly plastering the same Make: Legrand/Havells/L&T /INDOASIAN or similar | — | — | — | 37,800 | |
| — | 2.00 | — | — | ||
| Supply, Installation and commissioning of Instant geysers of 3KW, 3 ltrs and with standing capacity of 0.8MPa. Make: Havells/Bajaj/Crompton or similar | — | — | — | 8,998 | |
| — | 8.00 | — | — | ||
| Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 3 module duly erected flush to wall with required chiseling and finishing with cement mortar / POP as per required to match the background in an approved manner. Make: Legrand/Havells/GM/INDOASIAN or similar | — | — | — | 1,880 | |
| — | 52.00 | — | — | ||
| Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 6 module duly erected flush to wall with required chiseling and finishing with cement mortar/POP as per required to match the background in an approved manner. Make: Legrand/Havells/Schneider/GM/INDOASIAN or similar | — | — | — | 15,912 | |
| — | 32.00 | — | — | ||
| Supplying and erecting unbreakable concealed type modular switch box with double mounting plate for 12 module duly erected flush to wall with required chiseling and finishing with cement mortar / POP as per required to match the background in an approved manner. Make: Legrand/Havells/ Schneider/GM/INDOASIAN or similar | — | — | — | 15,520 | |
| — | 78.00 | — | — | ||
| Supply and erection of modular type 5 pin 6A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete. Make: Legrand/Havells/GMINDOASIAN or similar | — | — | — | 10,062 | |
| — | 78.00 | — | — | ||
| Supply and erection modular type switch 6/10A ISI mark approved make duly erected on provided plate and box with wiring connections complete. Make: Legrand/Havells/GM/INDOASIAN or similar | — | — | — | 3,900 | |
| — | 16.00 | — | — | ||
| Supply and erection of modular type 3 pin 16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete. Make: Legrand/Havells /GM/INDOASIAN or similar | — | — | — | 2,720 | |
| — | 16.00 | — | — | ||
| Supply and erection of modular type switch 16A ISI mark approved make duly erected on provided plate and box with wiring connections complete. Make: Legrand/Havells/GM/INDOASIAN or similar | — | — | — | 1,552 | |
| — | 368.00 | — | — | ||
| Provision of concealed wiring with two runs of 1.5 Sq.mm 1100 Volts and one run of flexible copper conductor 1.5 Sq.mm 1100 Volts FRLS PVC insulated wires ISI marked (Phase, neutral and earth)(upto 10 meters) in the PVC conduit pipe with 6A flush modular type switch including 2 way switches where ever required, ceiling rose, bulb holder and modular type plate cover to MS switch control box including all labour charges complete for light points, ceiling fans and exhaust fans points cat walk points and ioh service building points etc. accessories. | — | — | — | 2,73,424 | |
| — | 1460.00 | — | — | ||
| Supply and run of 2 nos, 2.5 sq.mm, 1100 V PVC (FRLS) insulated flexible copper conductor wires and one run of 1.5 sq.mm PVC (FRLS) insulated flexible copper cable for earthing in existing PVC conduit Pipe conforming to IS 1554-part 1. | — | — | — | 1,64,980 | |
| — | 620.00 | — | — | ||
| Supply and run of 2 nos, 4.0 sq.mm, 1100 V PVC (FRLS) insulated flexible copper conductor wires and one run of 2.5 sq.mm PVC (FRLS) insulated flexible copper cable for earthing in existing PVC conduit pipe conforming to IS 1554-part | — | — | — | 1,05,400 | |
| — | 330.00 | — | — | ||
| Supply and run of 2 nos, 6.0 sq.mm, 1100 V PVC (FRLS) insulated flexible copper conductor wires and one run of 2.5 sq.mm PVC (FRLS) insulated flexible copper cable for earthing in existing PVC conduit/Casing and capping pipe | — | — | — | 66,000 | |
| — | 2820.00 | — | — | ||
| Supply and concealed laying of 25 mm dia 2mm thick PVC pipe (ISI MARK) heavy mechanical stress FRLS with all required accessories including masonary work (chipping etc.) and labour charges etc | — | — | — | 1,15,620 | |
| — | 1450.00 | — | — | ||
| Supply and laying of 32 mm dia 2 mm thick PVC pipe (ISI mark) concealed in roof slab and wall with all required accessories including masonry work(chipping etc.) and labour charges etc (for main to sub mains). | — | — | — | 91,350 | |
| — | 14.00 | — | — | ||
| Supply, fixing and connecting of 2 pole 2 module 32A 30 mA Lexic RCBOs conforming to IEC 61009-2-1 as advised by the site supervisor with all necessary accessories complete or equivalent make. | — | — | — | 75,796 | |
| — | 14.00 | — | — | ||
| Supply, fixing , connecting and commissioning of Master control 32A TPN MCB as per the direction of the Engineer at site | — | — | — | 20,202 | |
| — | 6.00 | — | — | ||
| Supplying and erecting triple pole and neutral distribution board (TPNDB) with door surface/flush mounted with 4 ways for incoming and 12 ways for outgoing SP/TP MCB's on iron frame/laminated board as per specification No. SW-SWR/MCBDB with required chiseling and finishing with cement mortar/POP as per required to match the background in an approved manner Make: Legrand/Havells/L&T or similar | — | — | — | 15,072 | |
| — | 14.00 | — | — | ||
| Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB's on iron frame/laminated board as per specification No. SW-SWR/ MCBDB with required chiseling and finishing with cement mortar/POP as per required to match the background in an approved manner Make: Legrand/Havells/L&T or similar | — | — | — | 22,722 | |
| — | 14.00 | — | — | ||
| Supply, erection and marking TPN MCB 63A, 10 kA C series in provided distribution board as per specification No. SW-SWR/MCB Make: Legrand/ Havells/L&T or similar | — | — | — | 19,544 | |
| — | 108.00 | — | — | ||
| Supply, erection and marking DP MCB 16-32A, 10 kA B/C-series in provided distribution board as per specification No. SW-SWR/MCB Make: Legrand /Havells/L&T | — | — | — | 55,296 | |
| — | 46.00 | — | — | ||
| Supply, erection and marking SP MCB 16-32A, 10 kA B series in provided distribution board as per specification No. SW-SWR/MCB Make: Legrand/Havells/L&T | — | — | — | 8,832 | |
| — | 15.00 | — | — | ||
| Supply, fixing testing and commissioning of 4 Pole MCCB 63A suitable for operation on 415V, 50 Hz 3Phase AC supply in LT Panel with supply of all connected accessories and allied materials as per specification attached. Make: L&T/Legrand/Havells Or Similar | — | — | — | 41,835 | |
| — | 320.00 | — | — | ||
| Excavation of cable trench 30 cm widex90cm deep in all types of soils for HT/LTUG cable as per specification No.Y/E.cable laying/6/99 annexed | — | — | — | 39,040 | |
| — | 220.00 | — | — | ||
| Cutting of asphalted road/concrete/cement/under the track etc., and excavation of cable trench 30cm widex90cm deep road etc., for laying of HT/LTUG cable. After laying of cable the trench should be brought to its original position by providing tar/ concrete/ cement as per the site conditions and as per directions of Rly.Engineer. | — | — | — | 44,660 | |
| — | 220.00 | — | — | ||
| Supply and laying of ISI marked 4 core 25 sq.mm cross linked polyethylene (XLPE)insulated LT UG cable, PVC outer sheathed, armored with galvanized round steel wire or steel strip and with Aluminium conductor with cable termination/lugs and through joints wherever necessary as per site condition suitable for rated voltage at 1100 volts grade and conforming to IS:7098(Part-1)/1988with amdt. no. 1,2 & 3 (reaffirmed 2005) or latest. Make: Polycab/Finecab/Finolex/Havells or similar | — | — | — | 41,580 | |
| — | 2220.00 | — | — | ||
| Supply and running of 8 SWG GI wire is to be laid for earth continuity | — | — | — | 26,640 | |
| — | 20.00 | — | — | ||
| Supply and erection of earth electrode as per the enclosed specification.30 | — | — | — | 75,960 | |
| — | 900.00 | — | — | ||
| Supply and laying of HDPE pipe of PE-80 grade in PN-4 outer dia of HDPE pipe 110mm (nearest 4"" dia) and wall thickness minimum 4.1 mm maximum 4.3mm with ""T' joints, bends, elbows etc. including all other connected accessories. Make: M/s. Sudhakar/ Nagarjuna polymer/Nandi/Plasto or similar | — | — | — | 2,80,800 | |
| — | 220.00 | — | — | ||
| Supply, erecting and laying of HDPE pipe of PE-80 grade in PN-4 outer dia of HDPE pipe 63 mm (nearest 2"" dia) and wall thickness minimum 2.5 mm maximum 2.8mm with ""T' joints, bends, elbows etc. including all other connected accessories. Make: M/s. Sudhakar/ Nagarjuna polymer/Nandi/Plasto or similar | — | — | — | 27,280 | |
| — | 320.00 | — | — | ||
| Providing and fixing sheet metal work in CRCA sheet with fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. treated with anti-rust treatment and duly power coated as per the above specification. | — | — | — | 82,240 | |
| — | 62.00 | — | — | ||
| Supplying and erecting of any size electrolyte copper patti or bar in bus bar chamber / in panel or any other purpose,500 V with require capacity with 99.9%copper purity with fixing arrangement(like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete. | — | — | — | 72,416 | |
| — | 60.00 | — | — | ||
| Supply of 100 mm dia 'B' class ERW GI pipe conforming to IS: 1239 Part 1(2004) and fixing with suitable clamps on wall/building including laying of cable through GI pipe | — | — | — | 64,440 | |
| — | 120.00 | — | — | ||
| Supply, running and connecting of4 core 16 sq.mm. PVC insulated and PVC Round Sheathed, Multicore Annealed Bare Copper Conductor(flexible) industrial cable for Voltage Grade 1100 Volt, Conforming to IS694 : 2010 or its latest amendment | — | — | — | 1,25,520 | |
| — | 4.00 | — | — | ||
| Supply, fixing, connecting and commissioning of SMC cable termination junction Box of size340x200x105 with shock proof, rustproof, fire resistant, weather proof with IP65 protection suitable for termination of 2/4 core LT UG cables upto 240 sq.mm., 3 phase 415 volts including hylam sheet, heavy duty terminal connections, clamping arrangements etc. | — | — | — | 23,644 | |
| — | 2.00 | — | — | ||
| Supply and erection of 4-way Vertical Load line DB fitted with Busbars, Neutral Links and Blanking Plates suitable for 4 pole MCCB as incomer and 12 ways for MCBs as outgoing with all necessary material and labor complete with required chiseling and finishing with cement mortar/POP as per required to match the background in an approved manner. Make: L&T/Legrand/ Havells | — | — | — | 23,864 | |
| — | 260.00 | — | — | ||
| Supply, erecting and laying of 4 core 10 sq.mm copper cables XLPE insulated, cores laid up, PVC inner sheathed unarmored 650/1100V grade as per IS 7098(Part 1) 1988. | — | — | — | 1,21,160 | |
| — | 5.00 | — | — | ||
| Supply, erection, testing and commissioning of all material, excavation, and casting of cement concrete foundation/concreting in ratio 1:3:6 as per site condition and as directed by site engineer. | — | — | — | 30,035 | |
| — | 2.00 | — | — | ||
| Supplying and erecting selector switch suitable for voltmeter/ammeter for 3 phase AC supply 500/1000V, 50Hz, on provided box/ panel and duly connecting with necessary PVC wire leads and lugs. | — | — | — | 640 | |
| — | 2.00 | — | — | ||
| Supply & provision of 3 Nos RYB indication lamps of LED type including with all connected accessories complete. | — | — | — | 876 | |
| — | 6.00 | — | — | ||
| Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates | — | — | — | 5,268 | |
| — | 2.00 | — | — | ||
| Supplying and erecting panel mounting type digital ammeter having three and half digit LED display, external CT operated, calibrated for 0 to 1000A AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.(suitable to operate on 500V) | — | — | — | 2,722 | |
| — | 2.00 | — | — | ||
| Supplying and erecting panel mounting type digital voltmeter having Three and half digit LED display, calibrated for 0-750V AC suitable to operate on 500V AC supply with necessary PVC wire leads and lugs and mounting hardware on provided panel complete with calibration certificate from manufacturer.(suitable to operate on 500V) | — | — | — | 2,610 | |
| — | 2.00 | — | — | ||
| Supplying, installing, testing & commissioning of ETC Solar water heating system with out heat exchanger type of 500LPD capacity as per relevant Is specification | — | — | — | 1,56,000 | |
| — | 1000.00 | — | — | ||
| Water storage tanks: Providing and placingon terrace /staging (at all heights)polyethylene water storage tank ISI:12701 marked with cover and suitablelocking arrangement and making necessary holes for inlet, outlet and over flow pipes but without fittings and the base support tank. | — | — | — | 6,430 | |
| — | 200.00 | — | — | ||
| Mounting structures for tanks and Solar Water Heaters: Design and fabrication and supply of iron work for mounting of 2000 L water storage tank mentioned above consisting of various section of iron work including cutting, bending, drilling, welding, riveting with one coats of red oxide paint and two coats of enamel paints including fasteners as per site condition. | — | — | — | 23,600 | |
| — | 80.00 | — | — | ||
| 40 mm Water pipe: Supplying and erecting 32/40 mm (ID/OD) poly ethylene composite pipe duly jointed by compression/crimp fitted accessories, with internal as well as external end sealing arrangement | — | — | — | 41,760 | |
| — | 160.00 | — | — | ||
| 32 mm Water pipe: Supplying and erecting25/32 mm (ID/OD) poly ethylene composite pipe duly jointed by compression/crimp fitted accessories, with internal as well as external end sealing arrangement | — | — | — | 59,680 | |
| — | 14.00 | — | — | ||
| Taps: Providing and fixing 15 mm bathroom Brass tap and testing of joints complete | — | — | — | 5,950 | |
| — | 4.00 | — | — | ||
| Gate Valve: Providing and fixing 40 mm PP-R Gate Valve fusion welded, having thermal stability for hot & cold water supply and testing of joints complete | — | — | — | 3,040 | |
| — | 2.00 | — | — | ||
| Non return valve: Providing and fixing gunmetal non - return valve of 40 mm nominal bore approved quality (screwed end). | — | — | — | 978 | |
| — | 1960.00 | — | — | ||
| Supply and laying of 4 core 240 sq mm cross linked polyethylene (XLPE) insulated LT UG cable, PVC outer sheathed, armoured with galvanized round steel wire or steel strip and with aluminum conductor suitable for rated voltage at 1100 volts grade and conforming to IS:7098(Part- 1)/1988 with amdt.no. 1, 2 & 3 (reaffirmed2005) or latest. Make- Polycab, Finecab, Havells or similar | — | — | — | 29,43,920 | |
| — | 2.00 | — | — | ||
| Supply, fixing, testing and commissioning of Microprocessor Release 100-250A range; 4 Pole, MCCB in LT Panel with supply of all connected accessories and allied materials as per specification attached. Make: L&T/Legrand/Havells | — | — | — | 72,836 | |
| — | 1.00 | — | — | ||
| Supply, testing and commissioning of 100 KVA DG set with AMF panel as per specifications attached | — | — | — | 13,51,376 | |
| — | 10.00 | — | — | ||
| Supply and fixing of 25 x 3mm EC grade copper strip for connecting earth terminal to the bus bar in for maintenance earthing as per RDSO specification No. RDSO/PE/SPEC/PS/0109(Rev.0)-2008(Amdt. 1) or latest. | — | — | — | 8,900 | |
| — | 2.00 | — | — | ||
| Supply, Installation, Testing and commissioning of maintenance free earthing comprising of Electrode of 17.2 mm diameter Low Carbon Steel with 250 micron molecular copper bonded earthing rod of Length 3m along with 25 kg Carbon based environment friendly backfill ground enhancing compound required to fill up the excavated earth with required quantity complete as per RDSO specification No. RDSO/PE/SPEC/PS /0109(Rev.0)-2008 (Amdt.1) or latest. | — | — | — | 23,476 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC-2022.pdf
ATTACHMENT
GCCCorrectionSlips1to11_compressed.pdf ACS 1 to 11 to GCC 2022
ATTACHMENT
TB 02 202627 32 bed RR at CPSN
ATTACHMENT
GEM-511687747518904-180320254.pdf
ATTACHMENT
GCCCorrectionSlips1to11_compressed.pdf
ATTACHMENT
TenderNo.NED-E-01-2026-27RRatCPSN.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .