PMGSY road to Jemajori Road

Dismantling of existing structures like culverts, bridges, retaining walls and other sturcture comprising of masonry, cement concrete wood work, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable materials and stacking the serviceable materials with all lifts and lead of 1000m as per Technical Specification Clause 202

Earth work in embankment with approved materials obtained from borrow pits with all leads and lifts transporting to site,spreading, grading to required slope and compacting at OMC by Vibratory Roller to meet the requirement of Table-300.2 as per Clause 305 of MoRT&H Specifications dfor Road & Bridge works(4th Revision) complet including cost,conveyance,Royalities,Taxes of all materials,all labours,hire and running charges of all machineries,T&P ,sundries etc. complete as per spcification and direction of Engineer-in-Charge.

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement as per MORD technical Specification Clause 301 and direction of the Engineer in Charge (excluding cost of excavation and transportation to site).

Construction of granular Sub-base by providing Close graded Granular sub-base Grading-III material as per table 400-1 ,spreading in unifrom layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC , and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for road & Bridge works(4th. Revision) .

Excavation for road work in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, inaccordance with requirements of lines, grades and cross sections, and transporting to the embankement location with a lift of up to 1.5m and lead up to 1000m as per techincal specification clause 302.3

Providing laying spreading and compacting stone aggregate of specific sizes to water bound macadam specificatin including spreading in uniform thickness hand packing rolling with three wheel 80-100kN static roller in stages to proper grade and camber applying and brooming stone screening/ binding materials to fill up the interstices of coarse aggregate watering and compacting to required Grading-2 density as per technical specification clause 405

Providing and fixing of typical TRIP informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 of MoRD and as per direction of the Engineer-in-charge.

Providing and fixing of typical Citizen Information board as per MORD specification and drawing. Three MS plates of 50 x 5 mm. thick, back plate duty welded with 75 mm dia steel tubes back on edges as per drawings. The upper and lowe plate will be welded with MS flat iron frame of 50mm x 5 mm. The steel tubes dully embeded in cement concrete M-15 grade blocksw of 600mm x 600 mm x 750 mm below ground level. All MS will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with redimixed synthetic enamel paint of superor quality in required shade and colour. All selection of framed posts and steel tubes will be painted with primer and two coats of epoxupaint as per drawing Clause 1701 and Annexure - 1700.1.

Providing and erecting direction and place identification of semireflective sign boards as per IRC-67 made of 2mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures with reflective tape of engineering grade as per MORD specifications of required shade and colour. Supported and welded on two nos. 47mm x 47mm of 12 SWG square tube of 3050mm height duly strengthened by 25mm x 5mm MS flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 grade cement concrete 450mm x 450mm x 600mm, 600mm below ground level as per approved drawing and Technical Specification Clause 1701 (upto 0.90 square meter size) and as per the direction of the Engineer-in-charge.

Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1700, 300 & 800 of MoRD and as per the direction of the Engineer-in-charge.900 mm equilateral triangle