COMPREHENSIVE REPAIR/ REPLACEMENT TO LEAKAGE/ SEEPAGE AND CERTAIN MISC WORKS AT DRONACHAL TOP UNDER GE DRONACHAL

Amount

Taking down cement plaster of any description including raking out joints, hackisng for key, scrubbing down with water etc. complete all as specified and directed by Eng-in-charge.

Material and labour for rendering 10 mm thick in cement and sand mortar 1:6 on fair faces of brick work or cement concrete surfaces finishing the surface even and smooth without using extra cement including preparation of newly plastered surfaces of walls and applying three coats of white wash complete all as specified and directed by Eng-in-charge.

All as per Srl item No.2.00, but 15mm thick in cement mortar 1:4 finished fair and even using integral waterproofing compound including preparation of newly plastered surfaces of walls and applying two coats of cement base paint complete all as specified and directed by Eng-in-charge. Note:-Supply only of WPC shall be measured and paid separately.

Material and labour for rendering 5 mm thick in cement and sand mortar 1:4 on concrete surfaces of ceiling finishing the surface even and smooth without using extra cement including preparation of newly plastered surfaces of walls and applying two coats of complete all as specified and directed by Eng-in-charge.

Supply only integral water proofing compound

Material and labour for brickwork with sub class ‘B’ (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 including demolition & removing dubrish outside MD land complete all as specified and directed by Eng-in-charge.

Material and labour for sunken floor treatment as follows:-

Demolition of cement concrete in sunken floors incl. removing dubrish outside MD land complete all as specified and directed by Eng-in-charge.

Brushing neat cement slurry with 3.0kg of cement per sq. metre mixed with WPC @ 3% by weight of cement as per manufacturer's instruction to fill all hole and crack complete all as specified and directed by Eng-in-charge. Note:- Water tightness testing should be done after 24 hours

Material and labour for PCC (1:2:3) type B-0 using 12.5 mm graded stone aggregate with integral water proofing compound as per manufacturer instructions on bottom of sunken portion with proper slope towards spout complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately.

Material and labour for plastering on vertical sides and top surface of CM (1:3) 15 mm thick mixed with water proofing compound as per manufacturer instructions. Plaster shall be extended over PCC coving when the same is green i.e. PCC & plaster be carried out at the same time complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately.

Material and labour for 2 coats of Dr. Fixit krystalline water proofing coating compound shall be applied after laying sewage/ plumbing pipes with fixtures in position complete all as specified and as directed.

Material and labour for filling the sunken floor with PCC ( 1:5:10) type E-2 using bk aggregate over the treated surfacecomplete all as specified and directed by Eng-in-charge.

Material and labour spouts of 50mm dia GI pipe light grade projecting 450mm clear of face outer wall with PVC mosquito proof cap on inner face of pipe shall be provided to drain out seepage water , if any complete all as specified and directed by Eng-in-charge.

Note : Water tightness testing should be done after applying Dr Fixit epoxy compound, by pounding water for 72 hours & rectify defects if any till total elimination of defect. Debris to be removed outside MD land.

Demolition of cement Concrete (un-reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed by Eng-in-charge.

M&L for Providing, cement concrete 1:2:4 type B0 (using 12.5 mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges using WPC of approved make as per manufacturers instruction all as specified and directed (WPC shall be measured and paid separately)

M&L for 10mm thick cement plaster over PCC in CM 1:3 finished even and smooth (without using extra cement) and using WPC of approved make per manufacturers instruction all as specified and directed (WPC shall be measured and paid separately)

M&L for preparation and cleaning of newly plastered surface and applying two coat of Dr fixit Roof seal classic as per following direction 1. Marking of 2 x 2 m area on roof surface 2. Apply Ist coat on ready surface in one direction using 1.5 ltr/ 4 sqm area 3. Apply 2nd coat using 1.0 ltr/ 4 sqm after 12 hrs in perpendicular direction of 1st coat application

Cleaning and removing all scale and dirt etc from over head water tanks and from mouths of circulating pipe etc including dismantling & refixing at same or other place complete all as specified and directed by E-in Charge for following capacity including writing with oil paint the date of cleaning on tank ;

Exc 250 Ltrs but not exc 500 Ltrs

Exc 500 Ltrs but not exc 1000 Ltrs

Rotational moulded polyethylene water storage tanks of 500 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe, tank cover etc including taking down existing tank complete all as specified and directed by Eng-in-charge.

Rotational moulded polyethylene water storage tanks of 1000 Litres capacity, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe, tank cover etc including taking down existing tank complete all as specified and directed by Eng-in-charge.

S & F in repair, Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe 20 mm dia (minimum weight 210 gms) complete all as specified and directed by Eng-in-charge.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level ) complete all as specified and directed by Eng-in-charge.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 (using 20 mm graded stone aggregate) as in plinth protection, surface finished even and smooth without using extra cement, laid in panels n exc 3 mtr long and joints shall be filled with the mixture of bitumen and sand in (1:3) by weight, complete all as specified and directed by Eng-in-charge.

Material and labour PCC 1: 2 : 4 type B-1 (using 20mm graded crushed stone agg.) 40mm thick as in floor finishing surfaces of conc topping even and smooth with using extra cement complete all as specified and directed by Eng-in-charge.

Supply only glass dividing strips ,3 mm thick, 38 mm wide laid in position conforming to design pattern as approved by Engr-in-Charge.

Material and labour for 75mm thick plain cement concrete type D2 (1:4:8)(40mm graded aggregate) as in sub base of floor, path etc, complete all as specified and directed by Eng-in-charge.

Material and labour for machine pressed precast concrete interlocking paver block any shape and size with grey cement and pigment conforming to IS 15658-2006 of 60 mm thickness, M-35 Grade, approved colour and design laid over 50mm thick sand cushion and filling of joints with Narmada fine sand complete all as specified and directed by Eng-in-charge.

M&L for Chequered cement concrete tiles cast in rubber mould, glossy finish of approved colour, general purpose, double layer, size 25cm x 25cm x 22mm thick, with mixture of white and grey cement in equal proportions and pigments, set, jointed and pointed in neat cement slurry in floors with grey cement and pigments in floors and over 15 mm thick screed bed in CM 1:4 for laying floor finishes.

Demolition of stone slab and tiling of any description or thickness laid, bedded and pointed in any mortar complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust incl. brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and as directed.

Material and labour 25 mm thick PCC 1:2:4 type B-1, using 20 mm graded stone aggregate, including finishing surface of concrete topping even and rough as in screed bed complete all as specified and directed by Eng-in-charge.

Material and labour for glazed ceramic tiles coloured of size 350 x 450 x 7mm thick in walls etc, set & jointed in neat cement slurry and pointed in white or colours cement to match the colour of tiles over and including 10mm thick rendring in CM (1:4) complete all as specified and directed by Eng-in-charge.

Material and labour for non skid-ceramic tiles coloured of size area of each tile exc.0.06 sqm but not exc . 0.11 sqm (300 x 300 mm) X 6mm thick in floors etc, set & jointed in neat cement slurry and pointed in white or colours cement to match over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed by Eng-in-charge.

Material and labour Non skid coloured ceramic tiles 7 to 8 mm thick area of each tils exc.0.11 sqm but not exc 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed by Eng-in-charge.

All as per item No 29.00 but in skirting, vertical surface dadoes and riser etc. over and including 10mm thick rendring in CM (1:4) complete all as specified and directed by Eng-in-charge.

Material & labour for 20mm thick granite (of any type) work (table rubbed and polished)in steps, jambs, pillars, win dow-cills, cooking plat forms and like in cement mortar (1:4) including point ing in white cement (1:2) us ing marble dust with admix ture of pigment to matchwith shade of granite over and including 15 mm thick screed bed in Cement Mortar 1:6 complete all as specified and directed by Eng-in-charge.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete as directed.

Supply and fixing in repair light coloured vitreous china wash hand basin white available shape as approved of 550mmx400mm (minimun) on new pre-painted brackets excluding taps but including 32 mm bore waste fittings, brass, chromium plated etc complete all as specified.

Supply and fixing in repair Vitreous China squatting pan “Orissa pattern” size 580x440mm white with integral foot rest (excluding flushing cistern and flush pipe) with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes and bed concrete etc complete all as specified and directed.

Supply and fixing in repair Vitreous China wash down water closet pan (Pedestal Pattern) and trap (standard pattern) coloured as approved including connection to drain (or outgoing pipe) and to flushing pipe anti symphonize pipe etc. including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointing complete with fixing bolts complete all as specified and as directed.

Supply and fixing in repair Plastic water closet seat,any colour as available, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device and jointing complete all as specified and as directed.

Supply and fixing in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10ltrs capacity complete all as specified and as directed.

S&F in repairs Vitreous China bowl urinal flat back of size 465 x 355 x 265 mm white (minimum) with grating and union for discharge pipe (excluding flushing cistern flush pipe and waste pipe), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe)complete all as specified and directed.

Supply and fixing in repair of fancy type pillar taps cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shank supply and fixing fly nuts for iron pipe of 15mm bore fancy type.

Supply and fixing in repairs of fancy type chromium plated Bib tap, 15mm bore any make as given in list of makes as directed by the GE.

Supply and fixing in repair of CP brass fancy type stop cock with long shank & as concealed type/ angular type .

S&F in repair two way bib tap 15mm dia all as specified and directed.

S&F in repairs 32mm bore LDPE waste pipe for WHB/ sink complete all as specified and directed.

Supply and fix in repair PVC connection 15 mm size, of length 450 mm, with PTMT nuts complete all as specified and directed by Eng-in-charge.

S&F in repair Health faucet (ABS Body) mild steel CP suitable for 15mm dia pipe with 1.25m long flexible tube and ABS wall hook incl making connection and fixed in position complete all as specified and directed.

S&F Tubular towel rail aluminium anodised 20 mm dia D-type 60 cm long between flanges, including brackets and fixed to walls, complete all as specified and as directed.

Supply and fixing in repair CP soap dish complete all as specified and directed.

S&F in repair Toilet paper holder with flat recessed type stainless steel Complete all as specified and directed.

S&F in repair chromium plated shower roses 125 mm long with or without swivel joints, any size, including fixing fixing to steel pipe or union complete all as specified and direceted.

Taking up or down PVC/GI tubing of 15/20mm bore and connections complete all as specified and directed.

Supply and fixing in repair 20mm dia CPVC pipe of grade SDR - 11 and and plain fittings of SDR-11 on wall or ceiling or laying in floor /ceiling concealed type including all type of fittings complete all as specified directed by Engr-in-charge

Supply and fixing in repair 25mm dia CPVC pipe of grade SDR - 11 and and plain fittings of SDR-11 on wall or ceiling or laying in floor /ceiling concealed type including all type of fittings complete all as specified directed by Engr-in-charge.

cutting channels grooves or rebates n.exc 15cm girth and trimming surface complete all as specified and directed by Eng-in-charge.

S&F for PVC (SWR) pipes 110 mm bore of pipe, single socketed in any length with rubber ring joints fixed to walls including repair and replacement old pipe complete all as specified and directed by Eng-in-charge.

S&F 75mm dia PVC (SWR) pipe and single socketed in any length with rubberring joint laid in trenches or in floor including repair and replacement old pipe all as specified and directed.

S&F for PVC (SWR) bends of 110 mm bore and any radius complete all as specified and directed by Eng-in-charge.

S&F 75 mm bore PVC (SWR) bend in any radius complete all as specified and directed by Eng-in-charge.

S&F for Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large complete all as specified and directed.

Supply and fixing in repair 0.56 mm dia MS galvanised wire cloth with average width of aperature 1.18 mm and fixed with tinned tacks or galvanised wire staples, beads complete all as specified and directed.

Supply and fixing 3 mm thick sheet glass ordinary quality and glazing with oil putty in squares not exceeding 0.50 Sqm in each pane as including in repair complete all as specified and directed.

Supply and fixing for figured glass, 3mm thick, pin head type and glazing with oil putty or beads in squares not exc. 0.50 Sqm in each pane as in repairs complete all as specified and directed.

Supply and fixing 10mm thick toughned glass as in hinged doors, partitions automatic door sand similar work including cutting to shape, drilling holes required including taking out old broken/ unservicable glass complete all as specified and as directed

Supply and fixing for figured glass, 4.8mm thick, pin head type and glazing with oil putty or beads in squares not exc. 0.50 Sqm in each pane as in repairs complete all as specified and directed.

Material and labour for Securing glass of any description in existing Metal/wooden frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work (New length of frame reputtied shall be measured) complete all as specified and as directed.

Supply and fixing in repair 300 mm, mild steel ordinary rat tail rod pattern spring including roller and roller plate complete all as directed.

Supply and fixing in repair 40mm dia cupboard knobs fixed with nuts screws and washers of brass polished complete all as specified and as directed.

Supply and fixing in repair brass ,4 lever Locks, cupboard, grade I, size 50 mm fixed with shutter with necessary cutting and fixing complete all as specified and as directed.

Supply and fixing in repair Door closer aluminium (extruded) hydraulically regulated designation No 1 universal type, suitable for door shutters of 851 to 1000mm in width and weight between 61 to 80 kg and fixed complete all as specified and as directed.

Supply and fixing in repair double action Floor Spring Hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing poivet made of brass, other parts made of brass, other part made of mild steel heavy duty and fixed complete all as specified and as directed.

Supply and fixing in repair heavy duty hydraulic floor door spring fixed to floor for heavy toughend glass door including top ss bracket with pivot for fixing of glass with glass partition including all taking down and refixing of heavy glass any type all as specified and directed.

Supply and fixing in repair double body Floor door stopper of aluminium alloy body and tongue, anodised fixed in door shutters complete all as specified and directed.

Supply and fixing in repair for 75mm long Hasp and staple, aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified and as directed.

Material & labour in repair for 2nd class hard wood plain fillets, square, rectangular in section, making rebates for fixing prelaminated cupboard shutters clean sawn, secured with nails or brads in sectional area exc 13 & n. exc 25 sq. cm fixed with nails

Supply and fixing in repair 16 mm thick prelaminated particle board exterior grade,prelaminated side with decorative choice lamination& side balancing white lamination fixed with screws to timber frame work complete all as specified and directed by Eng-in-charge.

Extra over rate for item No 74.00 above for prelaminated partical board for external teak wood lipping 6mm thick fixed with nails complete all as specified and directed by Eng-in-charge.

Supply & fixing in repair Continuous (piano) hinges, mild steel, bright finish or electrogalvanised of width of flaps (when open) in 30mm.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size n. exc 1.5 Sqm each and removing from site complete all as specified and directed by Eng-in-charge.

All as per Srl item No.77.00 but area exceeding 1.5 sqm and not exceeding 4.00 sqm each complete all as specified and directed by Eng-in-charge.

Taking down shutters of any description, area exceeding 1 sqm and not exceeding 2.00 sqm each complete all as specified and as directed.

Taking down shutters of any description, area exceeding 2 sqm each complete all as specified and as directed.

Material and labour for taking down and refixing in same opening wood shutter exc 1 sqm but not exc 2.00 sqm including easing & adjusting and refixing with same hardware etc.

Supply and fixing Pressed steel frame for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including one shop coat of priming complete all as specified and as directed.

All as per item No 82.00 but of size 125 x 60 mm complete all as specified and directed by Eng-in-charge.

Material and labour for PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate as in filling of pressed steel frame complete all as specified and as directed.

Material and labour for cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate for fixing hold fast, coping, cills and filling in pressed steel door frames including necessary form work and finishing the surfaces to match with existing, complete all as specified and directed by Eng-in-charge.

Supply and fixing 35mm thick, IInd class hard wood plain, framed, panelled factory made shutters (two panel) with lock rail and panel of 12mm veneered particle board with commercial veneering on both faces. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated complete all as specified and directed by Eng-in-charge.

Supply and fixing 35 mm thick, 2nd class hard wood , glazed & skeleton factory made shutters, open rebated & prepared to receive glass, gauze etc. (without sash-bars), edges of framing plain, chamfered or rounded fitted with cut and metred beads for securing glass etc., sizes of members of shutters as specified in SSR Part-I, Section-8, clause 8.20(a) complete all as specified and directed by Eng-in-charge.

Supply and fixing 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Eng-in-charge.

Supply and fixing solid PVC Door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement complete all as shown in drawing of relevant item in MES, schedule Part-II , 2004 as specified and as directed.

Material and labour for anodised aluminium powder coated frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified Note:- minimum thickness of powder coating 50 micron.

Supply and fixing anodised aluminium powder coated door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified, Note : minimum thickness of powder coating 50 micron.

Supply and fixing anodised aluminium window and ventilator shutters,powder coated side hung / sliding type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Eng-in-charge.

Supply and fixing Butt hinges, 100 mm long medium weight, cold rolled mild steel, ISI marked complete all as specified and as directed.

Supply and fixing aluminium handles extruded type of size 125mm, complete all as specified and directed.

Supply and fixing 150 mm long, aluminium anodised, barrel tower bolts, of extruded section ISI marked complete all as specified and as directed.

Supply and fixing 250 mm long aluminium alloy anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cost or extruded sections or cost alumminium alloy complete all as specified and as directed.

Supply and fixing galvanized mild steel wire-cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed .

Material and labour for Painting to new wood or wood based surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with pink primer (one coat) finished with two coats of synthetic enamel paint complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise described for of any description.

Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F Mild steel, plain, black sheet 1.25mm in hearths; covering to door shutters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes unched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and directed

S&F for Roof trusses (Framed), trussed, purlins, crane gantries, rails and fastening and heavy brackets framing(Beam, tee, angle, channel or flat section) including distance pieces, cleats, etc. Gde Fe 410-W (Gde-E-250) quality-A complete all as specified and as directed.

Dismantling Plain or corrugated steel/ transluscent sheeting, any gauge, thickness, including Nainital or Similar pattern roof coverings etc complete all as specified and as directed.

M&L for Fibre glass reinforced translucent corrugated sheeting (approved color and pattern) with two corrugations side lap fixed with coach screw and washer in roof, wall etc incl L type or J-type hook instead of screw complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws and bitumen washer complete all as specified and directed.

M&L for preparation of new steel surfaces over 10cm width or girth of any description and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including beding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915mmx 460mm bowl size 410mm x 330mmx 160mm complete all as specified and directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply & fixing in repair rubber based door strip fixed to bottom edge of door shutter using small nails / self-adhisive type to minimise gap & avoid entry of insects inside house width & length as required at site complete all as specified and as directed.

Supply and fixing in repair 25mm dia PVC coated decorative mild steel drapery/ curtain rod cut to required size and fixed to brackets as specified and as directed.

Supply and fixing in repair 25mm dia PVC coated decorative mild steel drapery/ curtain bracket matching to item no 111.00 above all as specified and as directed.

Samaksh Enterprises

OBED AHMED SIDDIQUI

RAJPATI CONSTRUCTION

AJIT ENTERPRISES