Loading…
Loading…
Tender Value
₹10 L
EMD Value
₹20,000
Closing Date
7 Jul 2026, 6:00 pm7d left
Similar tender results from the same govt authority in the past 3 years.
AGE (I) Ayodhya Cantt
Asst Garrison Engineer (I), Military Engineer Services, Ayodhya Cantt PIN-224001
COMPREHENSIVE MAINT REPAIR TO MD ACCN IN ZONE B UNDER AGE (I) AYODHYA CANTT.
2026_MES_772443_1
8400/190/E8
Open Tender
Civil Works
180 days
Ayodhya Cantt
Please refer Tender documents.
8 documents required · 8 mandatory
₹500
AGE (I) Ayodhya Cantt
₹20,000
Yes
16 Jun 2026
16 Jun 2026
9 Jul 2026
17 Jun 2026
7 Jul 2026
1 Jul 2026
| Sl No | Description | Qty | Unit | Est. Rate | Est. Amount |
|---|---|---|---|---|---|
| 1 | M&L steel work in tubular trusses/column, railing, grills etc incl special shaped washer etc complete using ERW or induction butt welded tube complete all as specified and directed confirming to IS 1161:1979 grade 240 complete all as specified and directed. | 150 | Kg | - | - |
| 2 | Taking down chowkhat or frame with shutter (without taking off shutter from the frame) Area not exc 1.5 Sqm each all as specified. | 15 | Each | - | - |
| 3 | S&F powder coated anodised aluminium window/ventilator shutter sliding type with styles, rails size 40mm x 20mm, frame for chowkat size 44.5mm x 101mm, including channel to run three trackin frame, fixed glazing all are made from powder coated aluminium anodised section including necessary jointing cleat, glazing clips, rubber packing, anodised aluminium snap beading, screws of suitable size with and including 4mm thick frosted glass /tinned glass etc complete as specified.
Note:- (i) Three Nos of track to be provided.
(ii) In three tracks, shutter with frosted glass / tinned glass, wire gauge 0.56mm dia.
(iii) Thickness of aluminium section shall not be less than 1.00 mm) | 40 | Sqm | - | - |
| 4 | S&F powder coated anodised aluminium window and ventilator shutter side hung type without sash bar aluminium section weighing 0.55 kg/m including necessary joining cleats glazing clips,rubber packing ,anodised aluminium snap beading ,screw anodised aluminium fitting such as peg stays 150 mm long (1 no) hinges type B-21 100 mm long (2 no) suitable handle 1 no complete all as specified | 8 | Sqm | - | - |
| 5 | S&F powder coated aluminium (min thickness of powder coating 50 micron) for shutter of door ,window & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings where required including the cost of EPDM rubber/neoprene gaskets required.(Fitting shall be paid seperately ) with extruded builtup standard tubular sections/appropriate Z sections and other section of approved make confirming to IS:733 and IS: 1285 fixing with dash fasteners of required dia and size including necessary filling up gaps at junction i,e at top,bottom and side with required EPDM rubber/neoprene gasket etc Aluminium sections shall be smooth ,rust free ,straight,mitred and jointed mechanically where required including cleat angle,aluminium snap beading for glazing /paneling C.P. brass/stainless stell screws all complete as per architectural drawing and the directions of Enginer-in-charge | 20 | Kg | - | - |
| 6 | M&L for 4.0mm thick frosted/tinted sheet glass ordinary quality and glazing with beading n exc 0.5 sqm in each pane complete all as specified and as directed. | 6 | Sqm | - | - |
| 7 | Material & labour for non skid ceramic coloured tiles 7mm to 8mm thick area of each tile exc 0.18 sqm but n exc 0.38 Sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement in 15 mm thick screed bed in CM 1:6 for floor tiles complete including dismantling of floor tiles incl cement mortar bedding but not backing removing serviciable tiles to stores complete all as specified and directed by the Engr-in-Charge. | 30 | Sqm | - | - |
| 8 | M&L for glazed ceremic coloured tiled in vertical surfaces 300x450x7 mm thick(as approved by Engr-in-Charge) set and jointed in neat cement slurry and pointed in white or colour cement in 10 mm thick rendering in CM 1:4 for wall tiles to match including dismantling of wall tiles incl cement mortar bedding but not backing removing serviciable tiles to stores complete all as specified. | 60 | Sqm | - | - |
| 9 | Material & labour for non skid ceramic coloured tiles 7mm to 8mm thick area of each tile exc 0.11 sqm but n exc 0.18 Sqm coloured in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement in 15 mm thick screed bed in CM 1:6 for floor tiles complete including dismantling of floor tiles incl cement mortar bedding but not backing removing serviciable tiles to stores complete all as specified and directed by the Engr-in-Charge. | 20 | Sqm | - | - |
| 10 | M&L for Providing 25 mm thick, cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in flooring complete all as specified and directed by Engineer-in-Charge | 20 | Sqm | - | - |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.36 MB
BOQ_864950.xls
BOQ • 1.10 MB
TENDERDOCS.pdf
Tender Documents • 1.03 MB
Download all tender documents and submit your bid