PROVN OF GALVALUME SHEET COVERING OVER OPEN AREA FOR OPS BUILDING AT 44 WEU(B) ANUPGARH AND ADDITION/ALTERATION OF AIRMEN MESS AT KLP ANUPGARH UNDER GE (AF) SURATGARH

Amount

BOQ (PROVN OF GALVALUME SHEET COVERING OVER OPEN AREA FOR OPS BUILDING AT 44 WEU(B) ANUPGARH AND ADDITION/ALTERATION OF AIRMEN MESS AT KLP ANUPGARH UNDER GE (AF) SURATGARH.)

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed to galvalume sheet ,water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth, complete all as specified and directed by Engr-in- charge.

M&L for PCC 1:2:4 type B2 (using 40mm Graded stone aggregate) cement concrete in foundations, filling and mass concrete, complete all as specified and directed.

S&F for mild steel for framed structure like trussed, purlins, crane gantries, post rails and fastenings and heavy bracket framming (Beam, Tee, Angle, Channels, Tube, flat sections) including wind ties (flat iron) distance pieces, cleats etc conforming to Fe410-W (Gde-E-250) quality-A, complete all as specified and directed by Engr-in- charge.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St-240, complete all as specified and directed.

M&L for pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed by Engr. in-charge.

S&F for mild steel screws bolt (Machine made) with hexagonal or square heads one end screwed, each screwed end have two washer and one nut, dia of shank 16mm-20mm and but length of bolt exc 5cm but not exc 10cm and inserting in RCC wall in any description making good, complete all as specified and directed by Engr-in-charge.

M&L for preparation of new or previously untreated steel surfaces of any description, over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat or red oxide zinc chrome primer, complete all as specified and directed

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed .

S&F PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing) complete all as specified and directed.

Demolition of un-reinforced concrete in ground floors and pavings not exc 15 cm thick (below or above ground level ) complete all as specified and directed

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc, complete all as specified and directed.

Taking down chowkhats or frames not exceeding 1.5 Sqm each (Without taking off shutters from the frames), complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 sqm and not exc 4.00 sqm each (without taking off shutters from the frames), complete all as specified and directed.

Taking down shutter of any description not exc 1 sqm each, complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc, complete all as specified and directed.

Dismantling water tanks (PVC) exc 250 ltr and not exc 500 ltrs capacity, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:4 on fair faces of brick work or concrete surface mixed with water proofing compound and finished the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 25mm thick, PCC 1:2:4 type B-1 , using 20mm graded crushed stone aggregate for leveling the undulation floor after dismantling, complete all as specified and directed.

S&F for light shade vitrified ceramic tiles darks shade 10mm thick (Square/Rectangular) polished area of each tiles exc 0.42 sqm but not exc 1.00 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed.

S&F light shade vitrified ceramic tiles darks shade 10mm thick (Square/Rectangular) polished area of each tiles exc 0.42 Sqm but not exc 1.00 Sqm , fixed in wall dado/skirting etc . set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4, complete all as specified and directed.

S&F granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade, including 20mm thick screed bed in cement mortar 1:6, complete all as specified and directed by Engr-in-charge.

M&L glazed ceramic colour tiles in vertical surfaces size 600mmx 300mmx 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering in CM 1:4, complete all as specified and directed by Engr-in-charge.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of veneered particle board or plywood or bison board, complete all as specified and directed by Engr-in-charge.

S&F 2nd class hard wood of 30mm thick glazed and skeleton shutters open rebated and prepared to receive glass, gauze, etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc for window and ventilator, complete all as specified and directed by Engr-in-charge.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in squares not exc 0.5 sqm in each pane, complete all as specified and directed by Engr-in-charge.

S&F for aluminium alloy wire cloth. 0.45mm nominal dia of wire and average width of aperture 1.4mm and fixed with aluminium wire staples, complete all as specified and directed.

Cutting holes in brick work built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement mortar 1:2:4 type B-1 as required not exc half brick, complete all as specified and directed by Engr-in-charge.

S&F for 100mm long medium weight, cold rolled mild steel Butt hinges, complete all as specified and directed.

S&F for 150mm long aluminium, anodised barrel tower bolts of extruded section, complete all as specified and directed.

S&F for 150mm long extruded aluminium alloy handles, fabricated type, anodised, complete all as specified and directed.

S&F for 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of cover plate 150 mm, complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection/hard standing etc, finished smooth and even using extra cement, complete all as specified and directed.

Forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A', complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, complete all as specifeid and directed.

Supply only integral water proofing compound @2Kg by the weight of cement (ISI marked) of approved make, complete all as specified and directed.

S&F 500 litres capacity rotational moulded polyethylene White water storage tanks (Cylindrical vertical with thread cover closed top) double layered, hoisted & fixed in position including GI tank nipple and with union (two No each) fittings and making necessary connections to make the tank functional, complete all as specified and directed.

S&F 1000 litres capacity rotational moulded polyethylene White water storage tanks (Cylindrical vertical with thread cover closed top) double layered, hoisted & fixed in position including GI tank nipple and with union (two No each) fittings and making necessary connections to make the tank functional, complete all as specified and directed.

S&F in repair ball brass valve 20mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for Refixing or removal to store, complete all as specified and directed.

S&F for 15mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors, complete all as specified and directed.

S&F for 20mm bore medium grade galvanished tube with all fitting & fixed complete to walls or ceiling & laid in floors, complete all as specified and directed.

S&F for 20mm dia., aluminium alloy anodised tubular towel rails, complete all as specified and directed.

S&F for aluminium brackets for 20mm tubular towel rail 20mm dia, complete all as specified and directed.

S&F in repairs 20 mm dia gun metal, globe or gate valve with Iron wheel head Screwed both ends for Iron pipe, complete all as specified and directed by Engr-in-charge.

S&F in repairs 15mm bib taps with wall flange of chromium plated fancy type long shank screwed for Iron Pipe or for brass ferrule, complete all as specified and directed.

S&F in repairs 15mm bore pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed by Engr-in-charge.

S&F in repairs vitreous china ware wash hand basin white, flat back, 550mmx400mm size oval type including cutting for and pinning ends of brackets or erecting stand, complete all as specified and directed by Engr-in-charge.

S&F in repairs PVC connection of 15mm bore and 450 mm long with brass checknut and union etc, complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distamper emulsion over a 2-3mm thick wall care putty, complete all as specified and directed by Engr-in-charge.

M&L for preparing newly plastered surfaces of ceilings and applying three coats of white wash, complete all as specified and directed by Engr-in-charge.

Complete removal of old plastered surfaces of ceilings and applying one coat of white wash including preparation of old plastered surfaces, complete all as specified and directed by Engr-in-charge.

M&L for preparation of new wood surfaces and applying two coats of synthetic enamelled paint over coat of pink primer over 10cm width or girth, complete all as specified and directed.

M&L for preparation on old surfaces and applying one coat of synthetic enamelled paint on wooden surfaces over 10cm width or girth, complete all as specified and directed by Engr-in-charge.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base, complete all as specified and directed.

M&L machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80mm thickness, M-35 Grade with grey cement and pigment, complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc. 15cm thick spread, levelled and rammed including watering, complete all as specified and directed by Engr-in-charge.

Excavating post holes or similar holes, each not exc 0.50 cum, getting out insoft /loose soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exc 25 cm, watering, and removing surplus soil to a distance not exc 50m & making good surface, complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40 mm graded granite stone aggregate) in foundations, filling and mass concrete, complete all as specified and directed.

S&F for mild steel work of framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc., not exc 10 kg each brackets, conforming to Fe 290 Gde E-165 (Brackets over 10 kg each to be measured under ‘structural steel') complete all as specified and directed by Engr-in-charge.

S&F for wind ties for roof including securing bolts including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 etc, complete all as specified and directed.

M&L for PCC 1:2:4 type B0 using 12.5mm graded aggregate in levelling course, haunching, coping and similar works including rounded or chamferred on edges and formwork etc, complete all as specified and directed by Engr-in-charge.

S&F in repair 15 mm dia CP bib taps of cast copper alloy chromium plated with crutch or butterfly handle fancy type screwed for iron pipe, complete all as specified and directed.

S&F for 15mm bore stop valves chromium plated fancy type with long shank (concealed type) screwed down high pressure with crutch or butterfly handle , screwed both ends for iron pipe, complete all as specified and directed.

S&F in repairs 15mm angle valve, fancy type, chromium plated brass, including connectiong to PVC/CP connection, complete all as specified and directed.

S&F for fancy type pillar tap 15mm bore , cast copper alloy, ISI marked with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and directed.

S&F in repair ball valve 20mm high pressure PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed. ( minimum weight 20 mm- 210 mm) complete all as specified and directed.

S&F in repairs wash basins, vitreous china, white, flat back of size 550mmx400mm including brackets and cutting for and pinning in ends of brackets or erecting stand 32mm dia waste fittings, brass, chromium plated with long screwed shanks and fly nuts, 32mm dia HDPE waste pipe and including new brackets , complete all as specified and directed by the Engineer in Charge.

M&L for stainless steel sink with drainage board made of 1.00 mm thick sheet for kitchen or with plugs washers & wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm with bowl size 410mm x 330mm x 160mm, with and including PVC waste pipe and CP waste coupling 32 mm fixed as in repair and making good to disturbed surfaces, complete all as specified and directed by Engineer-in-Charge.

M&L for preparation new plastered surfaces and applying two coats of exterior acrylic emulsion paint (weather proof treatment ), over a coat of primer in camouflaging patterns, complete all as specified and directed by Engineer-in-Charge.

M&L for surface point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC casing caping of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan point or one call bell point controlled by one, one way switch including PVC switch board of required size or 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on existing MS concealed box for mounting of switch, regulators or bell push and casing caping terminal box for mounting ceiling rose/ holders etc, complete all as specified and directed.

All as per ser item No 73.00 here-in-before but 5 amps socket point independent, complete all as specified and directed.

All as per ser item No 73.00 here-in-before but 5 amps socket point on same board, complete all as specified and directed.

All as per ser item No 73.00 here-in-before but cable of size 2.5 sqmm for one 16 amps socket (Power) point independent, complete all as specified and directed.

M&L for surface submain wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn through in and including PVC casing caping/PVC conduit size with all fittings and accessories alongwith one single core green colour PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly including dismentling taking down old unserviceable wiring and making good to disturbed surfaces, complete all as specified and directed. Note:-Two run of cable with one run of earth wire and one run of casing capping/conduit will be measured as one length.

All as per ser item No 77.00 here-in-before but cable of size 2.5 sqmm, complete all as specified and directed.

All as per ser item No 77.00 here-in-before but cable of size 6.0 sqmm, complete all as specified and directed.

S&F for 5 Amp switch piano type single pole one way, complete all as specified and directed.

S&F for socket flush type 6 amps, 5 pin, 230v, complete all as specified and directed.

S&F for switch socket combination multipurpose 2-in-1 flush type 3 pin 16 amps and 3 pin 6 amps, 230v including dismentling taking down unsv one, complete all as specified and directed.

S&F for ceiling rose surface bakelite three terminal, complete all as specified and directed.

S&F for MCB, single pole, 6 to 32 amps, 240 volts, 10 kA breaking capacity, "C" curve including dismentling taking down unsv one, complete all as specified and directed. Make- Cat Part No 4085-87 to 4085-95 of Legrand or equivalent of Schinder/ABB

S&F for MCB, double pole, 6 to 32 amps, 415 volts, 10 kA breaking capacity, "C" curve including dismentling taking down unsv one complete all as specified and directed. Make- Cat Part No 4086-28 to 4086-36 of Legrand or equivalent of Schinder/ABB

S&F for MCB distribution board, double door, metal enclosure , SPN, 230 Volts, 4 way including dismentling taking down unsv one complete all as specified and directed. Make- Cat part No 5076 10 of Legrand or or equivalent of Schinder/ABB

S&F for MCB distribution board, Double door, metal enclosure , SPN, 230 Volts, 8 way including dismentling taking down unsv one, complete all as specified and directed. Make- Cat part No 5076 10 of Legrand or or equivalent of Schinder/ABB

S&F for metal plug and socket board with MCB SP 20 amp, 16 KA complete all as specified and directed. MAKE- Cat Part No- 5078 11 of Legrand or equivalent of Schneider/ABB

S&F for LED batten fitting ' 2' long, 10 watt, CDL 230 Volts , complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm two core copper flexible conductor cable with mounting casing box 2 nos including dismentling taking down unsv fitting any type, complete all as specified and directed. Make-CG Cat Part No- CCS-103-10-65-HL2-DP-NWH or equivalemt in bajaj/philips/havells

S&F for LED fitting, 20 watt, CDL, 230 Volts, 4 feet long , complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable incl LED lamp and mounting casing box 2 nos incl dismentling taking down unsv fitting any type, complete all as specified and directed. Make-CG, Cat Part No CCS-100-20-65-HL2-DP-NWH or equivalemt in bajaj/havells/philips

S&F for LED building security light 25 watt, 230V with lens and toughen glass top complete PF > 0.95 with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20/25 mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener, complete all as specified and directed. Make- CG Cat Part No LSTS--25-CDL-M or equivalent in /philps/havells/bajaj

S&F for exhaust fan 300 mm in sweep (Steel body) 230/240 volt AC complete with all acessories including making connection by using flexible wire of size 0.50 sqmm 3 core and making holes, grouting nut bolts in wall for exhaust fan, complete all as specified and directed.

S&F for geyser for hot water single phase AC 240 Volts, 50 Hz including connecting cable with plug top one complete all as specified and directed. Note. Unserviceable geser to be deposited to E&M store Yard .

M&L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified location), connected with galvanised steel earthing lead of 04 mm all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2 with pit cover, funnel, wiremesh, 32 mm dia light grade GI tubing for protection of GI lead 04mm, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS, complete all as specified and directed.

S&F of ceiling fan star rating with hook 1200 mm (48") sweep and connecting up complete with and including three core copper conductor flexible cord of 0.5 sqmm cross sectional area of required length from ceiling rose to porcelain connector block of fan suitable on working AC, SP 230 V electric supply including electronic fan regulator stepped, flush type including all connection, complete all as specified and directed.

Contract Amount shall be derived after affecting the amount of Schedule of Credit in General Summary on serial page No 17 of tender documents.

Gaurav India Corporations (BID ID -3150704)

RATHORE ENTERPRISES (BID ID -3150868)

M/s JUGAL KISHORE MISHRA AND SONS (BID ID -3146410)