SPECIAL REPAIR OF OTM ACCN BLDG NO T-24 INCLUDING CERTAIN REVENUE AND MINOR WORKS OF B/R AND E/M NATURE AT DAMANA UNDER GE JAMMU

Amount

B/R Portion: - Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m deep for foundation etc and getting out in any type of soil complete all as specified and as directed.

Material and labour for cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as in foundations, filling in and mass concrete complete all as specified and as directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar (1:4) complete all as specified and as directed.

Material and labour half brick thick brick work with sub class "B" bricks straight or curved on plan exceeding 6m mean radius built in CM (1:4) complete all as specified and as directed.

Material and labour form work to soffits of suspended slab such as roof slab, floor slabs, landing and similar work; not exceeding 200 mm thick complete all as specified and as directed.

Use and waste form work square, rectangular or polygonal to sides of columns, pillars etc. of rough finished surfaces complete all as specified and as directed.

Use and waste form work to sides and soffits of floor or roof beams, lintel, cantilevers, shelves etc. including support of rough finished surfaces complete all as specified and as directed.

Material and labour for RCC M-25 (design mix) beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed.

Material and labour for RCC M-25 (design mix) slabs supported on walls, beams and columns, floors, roofs, landings, balconies, canopies, deck slabs and in the shelves and the like complete all as specified and as directed.

Material and labour for steel reinforcement TMT bars 10 mm dia and over cut to length, bent to shape and tying with annealed mild steel wire 0.9mm dia complete all as specified and as directed.

Material and labour for steel reinforcement TMT bars 6 to 8 mm dia cut to length, bent to shape and tying with annealed mild steel wire 0.9mm dia complete all as specified and as directed.

Material and labour for rendering 15mm thick on brick work or concrete surfaces in cement mortar (1:4) finished even and smooth without using extra cement including mixing integral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and as directed. Note: - Water proofing compound to be measured and paid for separately.

Supply only integral water proofing compound complete all as specified and as directed.

Material and labour for rendering 10 mm thick on other than fair faces of brick work or concrete surface in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for rendering 5mm thick on brick work or concrete ceiling surfaces in cement mortar (1:3) finished even and smooth without using extra complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft / loose soil complete all as specified and as directed.

Removing excavated material not exceeding 50m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and as directed.

Material and labour spreading, levelling in layers not exceeding 25cm thick and well ramming complete all as specified and as directed.

Material and labour cement concrete (1:3:6) type C-2, 100mm thick PCC in sub base complete all as specified and as directed.

Material and labour broken brick hardcore of gauge not exceeding 63mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube supplying and fixing in opening as per specification complete all as specified and directed.

Supply and fixing factory made single piece solid panel PVC door shutter 30mm thick style consisting of frame made out of mild steel tubes for top and bottom rails. Mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for style and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the mild steel frame welded / sealed to the styles and rails with suitable PVC sheet beading and jointed together with solvent cement supply and fixing in the frame at site complete all as specified and as directed.

Material and labour steel window factory made with side hung shutters and tubular moulded frame of 16 gauge suitable for single shutter including projecting type hinges non friction with 3mm thick 100mm long handle and two no's tower bolts 100mm long welded on 3.0mm thick mild steel plate to each window shutter and including hold fast and one coat of zinc chrome primer complete all as specified and as directed.

Supply and fixing figured glass, frosted head type and glazing with oil putty in square not exceeding 0.5 Sqm in each pane 3mm thick complete all as specified and as directed.

Supply and fixing Aluminium anodised barrel tower bolts of extruded section with 200 mm bright bolts complete all as specified and as directed.

Supply and fixing mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and directed.

Supply and fixing Aluminium handle, cast type, anodised 150 mm long complete all as specified and as directed.

Material and labour for applying three coats of white washing on walls including preparation of newly plastered surfaces complete all as specified and directed.

Material and labour for applying three coats of white washing on ceiling including preparation of newly plastered surfaces complete all as specified and as directed.

Material and labour for preparation of new plastered surfaces of wall and applying two coats of cement based paint over alkali resistant primer complete all as specified and as directed.

Material and labour for preparation of new steel surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Material and labour for screed bed or bedding layer of mortar 15mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

Material and labour for 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar (1:4) and finished even and fair for receiving tiles complete all as specified and as directed.

Material and labour glazed ceramic tiles in vertical surface 450 X 300 X 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Material and labour non skid ceramic coloured tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for PCC 75 mm thick (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in filling with finishing surface even and smooth in plinth protection complete all as specified and as directed.

Supply and fixing water closet (squat pattern) with lime concrete bedding, vitreous china orissa pattern 580 x 440mm, white with integral foot rests (excluding flushing cistern and flush pipe) including connectoin to trap and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor complete all as specified and as directed.

Supply and fixing vitreous china wash down water closet pan (pedestal pattern) white including seat cover closed pattern with flat bottom complete all as specified and as directed.

Supply and fixing PVC (SWR) P trap 110/110 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) floor trap plain including jointing with solvent cement 75 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) reducer of 110 mm dia complete all as specified and as directed.

Supply and fixing PVC (SWR) vent cowl 75 mm bore complete all as specified and as directed.

Supply and fixing PVC (SWR) water closet connector with lip ring 110 mm complete all as specified and as directed.

Supply 10 litre capacity PVC valveless, syphonic action type flushing cistern low level white with inlet, ball valve, float and handle including connection to pipe complete all as specified and as directed.

Supply and fixing vitreous china bowl urinal flat back, size of 465 x 355 x 265mm white including waste pipe 32mm dia GI pipe, grating and brass union for discharge pipe complete including providing and fixing plug bedding urinal against wall in cement mortar (1:2) securing urinal to plug with and including 60mm long brass screws pointing around urinal back in cement etc complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Vitreous china urinal partition white of size 310 x 700 mm complete all as specified and as directed.

Supply and fixing urinal spreader of PTMT any colour for fixing with 15 mm dia pipe (minimum weight 60 grams) complete all as specified and as directed.

Supply and fixing vitreous china wash hand basin white flat back of size 550 x 400 mm with pedestal including bracket, cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed shank and fly nuts complete all as specified and as directed.

Supply and fixing stainless steel soap dish bar fixed with and including chromium plated brass screws and wooden / plastic cleats (minimum weight 300 grams) complete all as specified and as directed.

Supply and fixing towel ring of PTMT fixed with and including chromium plated brass screws and wooden / plastic cleats complete all as specified and as directed.

Supply and fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part - I of capacity 1000 litre complete all as specified and as directed.

Supply and fixing steel water tubing 15 mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

Supply and fixing steel water tubing 20 mm bore medium grade galvanised with all fittings including short lengths, fixed to walls, or laid in floor complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

Supply and fixing stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15mm bore complete all as specified and as directed.

Supply and fixing stop valve, cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 20mm bore complete all as specified and as directed.

Supply and fixing stop valve / angle valve cast copper chromium plated screwed down high pressure with capstan head suitable for 15 mm bore, screwed both ends for iron pipe complete all as specified and as directed.

Supply and fixing bib taps fancy type, cast copper alloy, with crutch or butterfly handle screwed down for iron pipe or for brass ferrule and fixed for bore of pipe 15 mm complete all as specified and as directed.

Supply and fixing pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe of bore 15 mm complete all as specified and as directed.

Supply and fixing PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 grams) complete screwed for iron pipe or brass ferrule of size 20 mm bore complete all as specified and as directed.

Supply and fixing 110 mm PVC (SWR), waste and vent pipes in any length with or without ears, with rubber ring joints laid in trenches or in floor complete all as specified and as directed.

Supply and fixing 75 mm PVC (SWR), waste and vent pipes in any length with or without ears, with rubber ring joints laid in trenches or in floor complete all as specified and as directed.

Supply and fixing 110 mm dia PVC bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

Supply and fixing 75 mm dia PVC bends (any radius) diminishing pieces or tapers (larger bore measured) complete all as specified and as directed.

Supply and fixing grating doom 100mm dia of PTMT (minimum weight 25 grams) complete all as specified and as directed.

Material and labour for construction of septic tank for 25 users, exceeding in ordinary soil, foundation in PCC (1:2:4), brick work in CM (1:4), RCC slab covers including RCC precast manhole covers having 6mm plate embedded all round / fibre reinforced cover with angle iron frame vent shaft and sludge chamber etc complete all as specified and directed as shown in Drawing No CEPZ-C-TD-13/01-05.

Material and labour for soakage wells exceeding in ordinary soil, foundation in PCC (1:3:6), wells of Honey combed and solid in M-25 concrete, including intercepting chamber, screen chamber brick work in CM, RCC cover slab in M-25 / RR masonry / filling with brick bats, complete of size 1.8 M dia X 3.0 M deep complete all as specified and as directed.

Material and labour for concrete bed to drain pipes of bore 150mm dia including packing under haunching against the sides of pipe after they are laid tested in cement concrete (1:4:8) type C-2 (using 40mm graded crushed stone aggregates) complete all as specified and as directed.

Material and labour for 150 mm bore / inner dia double wall corrugated HDPE Pipes (SN8) with integral socket and necessary fittings, laid in trenches, including jointed and overlapping of pipe complete all as specified and as directed. Make: - Astral, Supreme, Prince.

Material and labour for PCC (1:2:4) type B-1 using (20 mm graded crushed stone aggregate) as in blocks for hold fasts, benching, coping apex stones, bed plates and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. Note: - Form work required for these item included in the unit rate of this item.

Material and labour for pre-cast RCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in manhole cover slab fixed in position including necessary form work and set in CM (1:6) complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-2 (using 40mm graded crushed stone aggregate) as in surface channels and drains etc complete all as specified and as directed.

Surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

Material and labour for PCC 25 mm thick (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) as in filling with finishing surface even and rough to receive top layer complete all as specified and directed.

Material and labour for non skid ceramic tiles 7 to 8 mm thick (square / rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Material and labour glazed ceramic tiles in vertical surface (300 x 200 x 7) mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed.

Material and labour framed work Fe-290 (Gde E 165) as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete, drilled for fixing of steel sheeting or other covering. Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

Supply and fixing expanded metal welded steel wire fabric supplied and fixed complete to wood or steel members not exceeding 4.00 kg complete all as specified and directed.

Supply and fixing pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) as in floor / sub base and finished even and fair complete all as specified and directed.

Material and labour for Chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame n.exc 1.5 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

Taking down chowkats or frames with shutter w/o taking off shutter from the frame exc 1.5 sqm but n.exc 4 sqm each incl cutting holes for taking out hold fast or dismantling brick (holes cut and any other damage to jambs, wall for taking out hold fast shall be finished identical to existing finish without any extra cost to Govt) complete all as specified and directed.

Dismanting asbestos cement (corrugated or semicorrugated etc) sheets in roof covering complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section framed work of any description complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar incl all quoins, arches pillars etc and removing unserviceable material exc 100 mtr complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving's n.exc 15 cm thickness (below or above ground level) and removing unserviceable material exc 100 mtr complete all as specified and directed.

Dismantling boarding any description fixed in any position with nail including GI frame work complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or from concrete surface incl racking out joints hacking for key scrubbing with water etc complete all as specified and directed.

Material and labour for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:4 except bricks complete all as specified and directed.

Supply and fixing for 35 mm thick 2nd class hard wood plain framed, panelled shutter (two panel) of factory made with lock rail and panel of 12 mm thick veneered particle board with commercial veneering on both faces including wooden beads on both sides, one coat of pink primer. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing for 35 mm thick 2nd class hard wood factory made glazed and Skelton shutters open rebated and prepared to receive glass/wire gauge etc. without sash bar but with lock rail edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass/wire mesh etc sizes of member as per clause 8.20(a) of SSR part -I for door shutter complete all as specified and directed.

Supply and fixing 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Supply and fixing Helical door spring 300mm including roller and roller plate complete fixed with welding to existing steel chowkhats complete all as specified and directed.

Supply and fixing box type steel windows/Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler /AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar design as per drawing (iv) PCC block for embedding lugs complete all as specified and directed.

Supply and fixing 3 mm thick sheet glass ordinary quality glazing with steel pins, oil putty to steel windows and beads nails etc. to wooden surfaces as in square exc 0.50 sqm in each pane,complete all as specified and directed.

Supply and fixing in repair Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks,or galvanised wire staples complete all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

Material and labour for Rendering 15 mm thick cement plaster in cement mortar (1:6) on other than fair face of brick work or concrete surfaces of wall and to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for Rendering 15 mm thick cement plaster in cement mortar (1:4) on fair face of brick work or concrete surfaces of wall and to be finished even and smooth without using extra cement complete all as specified and directed.(incl all necessary scaffolding, lifting arrangement)

Material and labour for preparation of new wood or wood based surface and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and directed.

Material and labour for two coats of oil bound distemper of wall to newly plastered surfaces including preparation of surfaces with chalk whitening complete all as specified and directed.

Material and labour for one coat of oil bound distemper to old treated surfaces including preparation of surfaces complete all as specified and directed.

Supply and fixing 4mm thick of size 605X605 mm ,White pre-premiered, self embossed, Reinforced Designer Board for false ceiling Conforming to IS-14862 and ISO-8336:1993. As per specification under mention: (i)GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , Then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

Supply and fixing for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication complete all as specified and directed.

S & F Plates (plain or chequered channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as specified and directed.

Material and labour for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5cm and n exc 30cm long, Diameter of neck 16mm to 20mm complete all as specified and directed. Make:- Conforming to IS

Supply and fixing mild steel work of angle iron as in framed work such as cooler stand, door frames, grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; conforming to Fe.290.Gde-E-165 including one shop coat of primer complete all as specified and directed.

Material and labour for one coat of synthetic enamel paint tint after preparation of old surfaces of steel of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tint.

Material and labour for machine cut kota stone slab flooring 20-25 mm thick laid over and including cement screed base 15 mm thick in cement mortar 1:6, and roughening the surface including cutting as required, rubbing and polishing to granite finish over complete all as specified and directed.

Material and labour for machine cut kota stone slab 20-25 mm thick as in riser of steps, skirting, dado and pillar laid over and including rendering of 10 mm thick in cement morter 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including cutting as required, rubbing and polishing to granite finish complete all as specified and directed.

Preparation of old plastered surface including filling of small holes etc. and applying one coat of cement based paint complete all as specified and directed by Engr-in-Charge.

Supply and fixing in repair Stainless steel drapery rods of 25 mm dia complete with coloured conical end balls at both end, dia not less then 50mm and fitted with and incl MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in male and female pieces as required at site complete all as specified and directed.

Use and waste of formwork to edges of concrete flats , treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floors and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls , horizontal or sloping and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces complete all as specified and as directed by the Engineer in Charge

Material and labour for steel reinforcement TMT bars 5mm dia and over upto and incl 10 mm dia as in Binders,stirrups,spacer complete all as specified and directed.

E/M portion: - Taking down old unserviceable copper / aluminium point wiring concealed / batten (light, fan, socket or power) complete, including fixture and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type switch board wooden / iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and directed.

Material and labour for point wiring for one light/fan/call bell point controlled by one 5 Amp switch with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 sqmm copper conductor multistrand FRLS, PVC insulated (unsheathed) drawn into new concealed PVC rigid/steel conduit and into existing CI/pressed steel sunken / terminal boxes including 3.00mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and directed. Note: - (a) Wiring shall be done by using proper colour coding. (b) Earth wire shall be of green colour. (c) On RCC roof / ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Description all as per serial item No 118 here-in-before but one 5 pin socket outlet 5 amps on the same board complete all as specified and directed.

Description all as per serial item No 118 here-in-before but one 5 pin socket outlet, 5 amps, independent complete all as specified and directed.

Description all as per serial item No 118 here-in-before but for one 5 pin socket outlet 15 Amps on independent board with cables 2.5 sqmm size complete all as specified and directed.

Supply and fixing in replacement for switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and directed.

Supply and fixing in replacement stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as required complete all as specified and directed.

Supply and fixing in replacement switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and directed.

Supply and fixing in replacement Switch socket outlet combined 2 in 1,3 pin 5 amp and 15 amp flush type,240 volts complete all as specified and directed.

Material and labour in replacement for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Material and labour in replacement Self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed.

Supply and fixing in replacement Ceiling Rose 3 terminal surface type Complete complete all as specified and directed.

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and directed.

Material and labour for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCBs should be same make.

Supply and fixing in replacement 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing in repair SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Dismantling and taking down old unsv street/security lights and Material and labour for new LED street light fittings of 30 watt system wattage and high preesure die cast aluminium housing with sealed toughened glass cover, TIP 66 protection suitable for pole mounting SMD led array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W , 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor> 0.95, working temperature range -20ºC to 60ºC,built in surge protection more than 10kV with facility of power supply shall be removed without removing light fitting from pole incl make proper connection complete including cutting , welding , drilling holes, nut bolts, washer complete all as specified and directed by Engineer-in-charge.

Material and labour in repair for Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC 1:2:4 type B-1 pre-cast RCC cover slab using reinfocement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply and fixing in replacement plug top 15 Amps complete all as specified and directed.

Disconnecting & taking out defective service cable any size and any type from roof, pole, pipe, floor, wall etc complete all as specified and directed.

Supply and laying, connecting and testing XLPE underground cable insulated, and overall sheathed with aluminium conductor heavy duty 1100 volts grade 10 sqmm 2.0 core laid in trenches/ on poles/ road crossing or passing through existing/new pipe under road crossing, clamping on wall etc complete all as specified and directed. Note: (i) Earth work, sand, bricks , removing, returning filling Aluminium thimbles/lugs will be paid separately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are incl in the quoted rates. (iii) All equipments , machinery or tools if required for laying electrical cable through new/existing pipes are provided by the contractor without any extra cost.

Supply and fixing switch piano, flush type single pole one way 5Amp, 240 volts complete all as specified and directed.

Supply and fixing Switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and directed.

Supply and fixing Switch socket outlet combined 2 in 1,3 pin 5 amp and 15 amp flush type,240 volts all complete all as specified and directed.

Material and labour Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

Material and labour self ballast LED retrofit Lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and directed.

Supply and fixing ceiling rose 3 terminal surface type complete all as specified and directed.

Supply and fixing LED lights fitting 1x 10W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95 , 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete. (4' ft long ) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and directed.

Material and labour distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 4 way 240 volts double door complete all as specified and directed. Note:- Distribution board and MCBs should be same make.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and neutral current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing SPN 40 to 63 Amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

Material and labour for LED street light fittings of 45 watt system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, TIP 66 protection suitable for pole mounting SMD led array with lense, cool white 6500 K, LED efficacy >120 lm/W and system efficacy 110 lm/W , 240 Volts AC, 50 Hz, CRI>70% operating voltage range 160 V-270 V, Power factor> 0.95, working temperature range -20ºC to 60ºC,built in surge protection more than 10kV with facility of power supply shall be removed without removing light fitting from pole incl make proper connection complete including cutting , welding , drilling holes, nut bolts, washer complete all as specified and directed.

Material and labour for Earthing complete with galvanised mild steel earth plate electrode of size 600x600x6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised ironl including PCC pit in PCC (1:2:4) type B-1 pre-cast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube flor watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and directed.

Supply and fixing plug top 15 Amps complete all as specified and directed.

Supply, installation, commissioning of hi wall split AC all weather (Cold/HOT) unit indoor/out door complete with cord less remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 3 star rating and EER 3.2 of capacity 1.5 Ton complete all as specified and directed.

Supply and fix Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type & desined for input variation between 170 v to 250 v with output voltage stabilized at 230 volt with accuracy of +2.5% and of capacity 5 KVA all as specifed and directed.

Supply and draw sub main wiring in pairs of two run 6.0 sqmm single core PVC insulated, unsheathed multistarnded copper conductor cabel 1100 Volt grade, draw through and including PVC conduit medium duty and accessories of 25 mm size and fixed with PVC saddles and cadmium plated steel screws to the surfaces of the wall/ceiling including one run of 2.5 sqmm single core PVC insultated unsheathed copper earth continuty conductor all as specified and as directed. Note: - Two runs of single core cable with one run of earth continuity conductor including PVC conduit accessories shall be measured and paid as one length.

Supply and fixing factory made double door board distribution in sheet steel enclosure with 200 Amps rated bus bar, SPN, 2 way, 240 Volts suitable for housing MCBs complete all as specified and as directed by Engineer-in-Charge.

Supply, installation, commissioning of hi wall split unit indoor / outdoor complete with cord less remote control unit and with in built air ioniser and plasma filter for better indoor air quality with minimum 5 star rating and EER 3.2 of capacity 2.0 Ton (Invertor tech) with Voltage stabilizer for automatic operation, single phase naturally air cooled indoor type and designed for input variation between 170 v to 250 v with output voltage stabilized at 230 volt with accuracy of +2.5% and of capacity 5 KVA including necessary wiring and double door board distribution in sheet steel enclosure with 200 Amps rated bus bar, SPN, 2 way, 240 Volts suitable for housing MCB's complete all as specified and directed.

NOTE NO 1: - Samples of materials as approved will be kept in GE's sample room. NOTE NO 2: - All fittings and fixtures mentioned above will be fixed to the satisfaction of Engr-in-Charge and GE. NOTE NO 3: - All plumbing works shall be laid or fixed as to be completely air tight or water tight as specified and Contractor will furnish its certificates towards air / water tight before completion of work under the Contract. NOTE NO 4: - Warranty certificate to the Engineer-in-Charge where ever applicable shall be submitted by the Contractor at the time of fittings.

M/S BHAGMAL AND SONS

STAR CONSTRUCTIONS

M/s Koul & Sons

Bidder Name

Shri Karshni Builders

STAR CONSTRUCTIONS

M/s Koul & Sons

M/S BHAGMAL AND SONS