SPECIAL REPAIR TO BLDG NO. T-4 (ADM BLDG) ZONE 9A AT TALBEHAT MIL STN

Amount

Dismantling of AC sheet (corrugated or semi corrugated etc) including AC ridges in large patches as in roof covering complete all as specified and as directed. Note:- opening of existing wind tie where required for taking down of AC sheet is deemed to be included in the rate quoted .

Dismantling of timber scantling 40 Sqcm and over in section in any position such as in rafter, purlins etc in unframed work complete all as specified and as directed

Dismantling of timber fillets , rails, posts, rafters, purlin etc under 40 sqcm in section, in any position in unframed work complete all as specified and as directed.

M&L for 2nd class hard wood exc 13 & n exc 25 Sqcm plain fillets, square, rectangular in section, clean sawn, secured with nails or brads complete all as specified and directed

M&L for clean sawn 2nd class hard wood as in scantling more than 40 Sqcm in sectional area fixed to timber/iron frame work complete all as specified and as directed Engr-in-Charge

Cutting holes into or through brick wall built in cement lime mortar and walls of cement concrete of superficial area exc 150 sqcm but n exc 400 sqcm and making good in CM 1:3 or cement concrete 1:2:4 type B-1 as required.

S&F rolled mild steel section work as in main and cross beam, hip and jack rafters purlins where connected to common rafters and running rails and guides for sliding door fixed with angle cleats or other connecting plates and cooler stand and similar work confirming to Fe 410W(Gde E-250 quality A) complete all as specified

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick, Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5 mm thick,Trapezoidal roofing profile with 190 mm Pitch & 29 mm depth of profile of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.(For sun shed)

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5 mm thick of any colour having tensile strength of 550 Mpa fixed with self tapping screws as specified & directed.

M&L Preparing surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with two coats of creosote oil all as specified and directed.

M&L Painting to new steel and iron surface of any description over 10cm in width or girth not otherwise described with two coats of synthetic enamel paint over coat of red oxide primer complete all as specified and directed

Dismantling wall and celling board (fibre, pulp, insulation etc) any thickness including cover fillets as directed.

S&F false ceiling with Everest Fibre Cement Designer tile Ivory painted (High Pressure Steam Cured) of 4mm thickness (as per IS:14862) of size 595x595 mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and 15x32 mm made from 0.30 mm thick sheet, spaced at 1200 mm c/c and cross "T" of size 15x32 mm made of 0.30 mm sheet, 1200mm long spaced between main "T" at 600 mm c/c to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size15x32 mm made of 0.30 mm thick sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 15x20 mm made of 0.30 mm thick sheet and laying false ceiling tiles in the grid including , required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI soffit cleats fixed to existing RCC lintel with dash fasteners, GI adjustable rods of 3mm dia with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15mm of all T -sections shall be centra black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, all complete at all heights as per direction of Engineer-in-charge.

M&L PCC (1:3:6) type C-2 using 20mm graded stone aggregate 75mm thick as in plinth protection finished fair even laid in alternate bays n.exc 2m in length all as specified and directed.

M&L PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in band,beam,benching of drain,man hole,coping,slightly rounded or chamfered angles and throating,and similar work including necessary form work all as specified and directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding, and rubbish off premises etc complete all as specified and directed.

M & L for Non-skid digital coloured Ceramic tiles 7 to 8 mm thick ( square /Rectangular) area of each tile exceeding 0.18 sqm but not exc 0.38 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement to match with tile laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and directed.

All as the item above but as in skirting but tile laid over 10mm thick CM (1:4) plaster complete all as specified.

S&F vitrified ceramic tiles 10mm thick (square/ rectangular) polished, light shade, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick rendering in CM 1:4 complete all as specified and as directed.

S&F vitrified ceramic tiles 10mm thick (square/ rectangular) polished, light shade, area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 sqm, in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in as in vertical surface like dado/ skirting etc including 15mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L for coloured Glazed ceramic tiles 600 x 300 x 7mm thick tiles on walls, set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile over and including cement mortar 1:4, 10mm thick plaster complete all as spd & directed.

Demolition of stone slab and tiles of any description or thickness in floor aprons etc laid / bedded and pointed in any mortar.

M & L for 20mm thick granite on kitchen platform and similar work over & including 15mm thick screed bed in CM 1:6 laid over sand stone slab machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing complete all as specified & directed.

Rounding to edges of stone slabs on edge, such as in steps, cooking platform and other similar situation. complete all as specified & directed.

Taking down cement or cement lime plaster on brick wall, ceiling incl. Raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

Demolition of stone/ brick masonry built in cement or cement lime mortar as in portion ordered and directed.

M&L for brick work with old size sub class B bricks straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

Material & Labour for Brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in cement mortar 1:4 complete all as specified and as directed.

M & L 15mm thick plaster in CM 1:6 on fair surfaces of walls finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for 15mm thick plaster in CM 1:4 on fair faces of brick work or concrete surface finished even and smooth w/o using extra cement complete all as specified and directed.

M&L for preparing of surfaces of walls, pillasters, cornices etc by washing, rubbing down & stopping etc and applying one coat of oil bound distemper in any colour complete all as specified and directed.

M&L for preparation of old plastered or un-plastered surface including brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of weather proof exterior emulsion paint complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall over a coat of primer on surface and applying two coats of oil bound distemper complete all as specified and directed.

M&L for preparation of plastered surfaces of wall and applying two coat of weather proof exterior emulsion paint complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel and iron work of any description over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

Taking down chowkats or frames exc. 1.5 but n.exc 4sqm each with shutters (W/o taking off shutters from the frame) and removal to store complete all as specified and as directed

-Ditto- but n.exc 1.5m2 each -ditto-.

Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 65 x100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant 152 SECTION 8 and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F powder coated anodized aluminium frames for door, window , ventilators with one or more rebates including joining cleats for fixing etc complete all as specified and as directed by Engr-in-charge

S&F Powder coated anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, rubber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminium snap beading screws etc complete all as specified.

S&F Powder coated anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc complete all as specified

S&F powder coated aluminium anodized side hung type window/ventilators shutter without sash bars section weight not less than 0.55Kg/RM with extruded built up standard tubular and other sections of approved make according to IS(thickness of powder coating not less than 50micron including necessay glazing clips weight not less than 0.124Kg/Rm for fixing sheet glass anodized aluminium fittings/fixtures such as required number of roller of suitable size interlocking cleats/ plates etc as required for complete fixing window shutters complete all as specified and as directed by Engr-in-charge. Note:- Only aluminium shutters for the window shall be measured in sqm sheet glass and wiremesh etc shall be measured and paid in respective items

M&L powder coated aluminium window shutter sliding type section not less than 0.55 Kg/RM, three shutter two glazed and one gauged including joining cleat,glazing cleap,rubber packing aluminium snap beading,screws,locking arrangement complete all as specified and as directed by Engr-in-charge.(Measurement shall be done leaf basis) Note:- Glass and Wiremesh paid Seprately.

S & F Factory made single extruded WPC (Wood Polymer Composite) solid Decorative type flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) ®

S & F Factory made single extruded WPC (Wood Polymer Composite) solid Decorative type flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with ecessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately) ®

S&F 35mm thick IInd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed

S&F in position 4.8 to 5mm thick clear float glass of ordinary quality and glazing with glazing clips including necessary rubber packing to aluminium frame exc 0.5 sqm in each pane complete all as specified and as directed.

S&F in position 4.8 to 5mm thick frosted glass on one side quality and glazing with glazing clips including necessary rubber packing to aluminium framen n. exc 0.5 sqm in each pane all as specified and as directed.

M&L for Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors,ladders; framed baluster,railings and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

S&F butt hinges Stainless steel size 100 mm size complete all as specified and directed.

S/F 125 mm size Aluminium handles, cast type, anodised and fixed of approved make & ISI marked.

Supply and fix 150mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

Supply and fix 200mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

S/F 150 mm size Aluminium handles, cast type, anodised and fixed of approved make & ISI marked.

Supply and fix 250 mm long aluminium alloy anodised sliding door bolts with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed by the Engr-in-Charge.

S & F 150 mm long floor door stopper of Aluminium alloy body tongue, anodised, with hard drawn steel spring fixed to door.

S&F in repair Stainless steel towel rail 20mm dia D type 60cm long between flange all as specified and directed by Enge-in-Charge

S&F in sheet glass assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated brackets guard and railing 60cm long complete all as specified and directed by Engr-in-Charge

S&F in repair chromium plated corner shelf complete all as specified and directed by Engr-in-Charge Make:- Parryware or equivalent in specified makes

S&F Sink made of stain less steel 1mm thick kitchen or laboratory with plugs, washers and waste pipe including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union overall size not less than 495x429mm, bowl size 410x330x 160mm complete all as specified and directed.

M&L for preparing the new wooden surface & applying two coats of synthetic enamel paint (1st grade) over one coat of pink primer over 10Cm width or girth complete all as spd & directed.

S & F Stailess steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed on wooden/steel frames with tinned tacks or galvanized wire staple & complete all as specified and directed.

Dismantling of existing unserviceable water tank of any description capacity exc 250 Ltr but n.exc 500trs capacity each complete all as specified and directed

S&F 500 litre cap rotational moulded polythelene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed including s and f of 20mm dia Ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm-210gms

S&F in repair ball valves PTMT high pressure with epoxy coated aluminium rod and high density plastic ball, screwed for iron pipe, 20mm bore compete (Minimum weight 210 gm) complete all as spd & directed.

Supply & fixed 50mm bore LDPE (Low density Polyethylene Pipes) of pressure rating 6Kgf/Sqcm fixed complete to walls,ceilings or in floors including taking down of old GI tubing, 40 mm bore all as specified and directed.

S&F in repair One piece ceramic floor mounted western water closet white with soft close seat cover including flush tank, trap and all fittings complete all as specified and as directed, Note:- The size, colour, design and Make shall be Approved by Eng-in-Charge.

S&F in repair PVC valveless syphonic action type low level flushing cistern, 10 Ltrs capacity White, with inlet ball valve, float, handle with 32mm PVC flush pipe, fixed on walls by driling holes and using PVC rawl plug of suitable size complete all as specified and directed.

S&F in repair Oval shape WHB size 560 x 410mm of including brackets,including CP waste coupling 32mm,waste pipe complete all as specified and directed.

Supply and fixing vitreous china premium quality/1st quality wash down water closet EWC with & incl with ‘P’ or ‘S’ trap of dia 100mm including provn of lime concrete bedding .

Supply and fixing plastic water closet seat white, closed pattern with flat bottom and cover and mild steel C.P. or Aluminum hinging device.

S & F in repairs Brass CP mixer for WHB for mixing hot & cold water screwed down for iron/CPVC pipe and fixed with Connecting Legs & Wall Flanges, complete all as specified and as directed.

Supply and fixing, bib tap screwed down high pressure, cast copper alloy,fancy type, ISI marked, with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified.

S&F 15mm bore concealed stop valve type chromium plated cast copper alloy screwed down high pressure screwed both ends for iron pipe or for union all as specified and directed by Engr-in-charge.

Supply and fixing (in repair) angle cock 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or unions, complete all as specified. (Note : Weight of cock shall not be less than 0.575kg)

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

S&F in repair brass chromium plated tubular towel rail 20mm dia 'D' type 60cm long between flanges all as specified and directed by Engr-in-charge.

Supply & fixed PVC connections 45cm long including 15mm bore PTMT nuts on both ends complete all as specified.

Supply & fixed stainless steel grating openable 100mm dia without hole including fixing with white cement complete all as specified.

Supply & fixed glass shelf assembly consisting of made out of 5.5 mm thick glass shelf 12 cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F 15mm dia pillar taps cast copper alloy with capstan heads, cromium plated screwed down high pressure with or without lettered Hot or Cold with long screw shanks abd fly -nuts screwed for iron pipe and fixed

Taking up or down steel tubing and connection 15 mm bore and removing the same from site/keeping aside for reuse complete all as specified and directed.

All as per srl item above but 20 mm bore

S & F water tubing 15 mm bore, medium weight, ISI marked galvanized with all fittings and fixed to walls, ceiling or laid in floors complete all as specified and directed.

All as per srl item above but 20 mm bore

M & L for refixing 15mm bore old GI tubing to walls, ceiling or laid on floor including necessary cleanig, cutting, screwing and new fittings such as elbow, Tee, union, socket, reducer etc.

All as per srl item above but 20 mm bore

S&F in repair Soap dish, any type, fixed to plugs with chromium plated brass screws embedded in the wall complete all as sped & directed.

Demolition of Reinforced Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) (reinforcement cut as required to facilitate demolition) complete.

M&L for form work, fair finished to soffits of suspended slabs such as roof slabs, floor slabs, landing and similar works flat n exc 200mm thick (Horizontal or slopping) etc complete all as specified and directed.

S&F steel reinforcement of TMT Bars of size 8mm dia and over cut to length bent to shape as required including cranking hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified and directed.

S&F in repair Stainless steel 20mm dia curtain rod including fixing brackets complete all as specified and directed.

S&F Stainless steel knobs with bracket fixing at end of pelmet rod complete al as spd & directed.

S&F PVC floor trap size 75mm dia out let with grating including connection to waste pipe with cement jointingcomplete all as specified and directed

S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints laid in trenches.

S&F PVC (SWR) pipes 110mm dia single sockted in any length with rubber ring joints fixed to walls.

S&F PVC (SWR) bends 110 mm bore of any radius

S&F PVC (SWR) vent cowl 110 mm.

Material and labour in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material and labour in repairs PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement including jointing to waste pipe fixed in cement concrete type-B-1 (1:2:4) using 12.5mm brick aggregate all as specified and directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre perilinear metre of perimeter wall including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment of voids in masonry, alongwith wall below concrete or masonry apron using chemical emulsion @ 1.00 litre per holes, soil under existing floors using emulsion @ 1.00 litre per hole, including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) and match the existing floors complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sqm of the vertical surface of the sub structure to a depth of 300mm including excavating channel along the wall and rodding, returning filling, ramming and consolidating etc complete complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment of soil under existing floor using chemical emulsion 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) and match the existing floors using emulsion @1 litre por hole complete all as specified and as directed.

Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed

Taking down carefully copper/Aluminium point wiring (light/fan/socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets etc, removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed.

Taking down carefully complete light fittings removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of wall, floors etc complete all as directed.

Taking down Distribution Boards along with MCB's incl removing the same from site and making good to the disturbed surface complete.

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc complete.

M/L for point wiring concealed type with 1.5sq mm FRLS PVC insulated unsheathed single core multistranded copper conductor cable 1100 volts grade incl 1.5 Sq mm PVC insulated unsheathed copper conductor cable as earth continuity conductor drown through in and incl FRLS PVC rigid conduit not less than 20 mm dia with its accessories pressed steel terminal box incl 3mm thick ISI marked laminated sheet cover for fixing switches/socket/regulators and making good disturbed surfaces of wall, floors etc for the following :- Wire: Make - Finolex/V-guard/Polycab/KEI/Havells/Plaza PVC conduit: Make -Polycab/Precision/Plaza/Kalinga Note:- On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit/PVC Casing capping and its accessories.

One light/fan/bell point controlled by one No piano type switch 5 Amps single pole one way

One socket outlet 5/3 pin 6 Amps controlled by one switch on the same board.

One socket outlet 5/3 pin 6 AMPS controlled by one switch on independent board.

All as per item NO.114 above but 3 pin socket out let 15/16 Amps on the independent Board all as spfd with single core unsheathed PVC insulated cable multistranded copper conductor of size 2.5 sq mm for phase & neutral & 2.5 sq mm for earth continuity conductor.

S&F Switch Piano Flush button single pole one way 5/6 Amp. MAKE:- Havells/Anchor/Gold Medal/Simon/Legrand

Piano Flush button single pole one way 15/16 Amp. MAKE:- Havells/Anchor/Gold Medal/Simon/Legrand

S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp, 240 volt. MAKE:- Havells/Anchor/Gold Medal/Simon/Legrand

S&F socket outlet 2 in 1, 3 pin & 2 pin, 5/6 Amp and 15/16 Amp, 240 volt. MAKE:- Havells/Anchor/Gold Medal/Simon/Legrand

S&F ceiling rose surface bakelite 65mmx50mm 100watt three terminal. Make : Havells/Anchor/Gold Medal/Simon/Legrand

S&F step type electronic fan regulator flush type on the existing phenolic laminated sheet

S&F Lamp holder Batten holder PVC/Polycarbonate insulated body with metal ring and back plate for batten fitting

S&F Ding dong type AC 230Volts, Single pole

S&F Bell push flush type 5 Amps AC 230V single pole

S&F Switch modular type with plate and cover single pole one way 6/10 Amps 240 V

S&F Switch modular type with plate and covert single pole one way 16/20 Amps 240 V

S&F Switch modular type socket 2&3 pin 6/10 Amps flush type with plate and cover suitable for 2 module 240 V

S&F Switch modular type socket 2&3 pin 6/16 Amps flush type with plate and cover suitable for 2 module 240 V

S&F Bell push flush type 5 Amps AC 230V single pole one way 6 Amps 240 V

S&F Fan regular modular type electronic with white cover with frame for modules 120 Watt 240 Volt Make: Sch A item Serial No. 7.00 to 21.00 Havells/Anchor/Gold Medal/Simon/Legrand

M&L concealed sub main wiring with two single core PVC FRLS insulated unsheathed stranded copper conductor cable FRLS, 02 runs of 01 Single core of size 6 sqmm (for main current) drawn in & incl PVC conduit conduit less than 20mm dia ISI marked with all accessories such as tee, bend, joint cover etc round / square blocks at junctions etc, all as per site requirements ISI marked with one run of 01 Single core of size 6 Sqmm (As earth wire) PVC insulated unsheathed stranded copper conductor as a continuous earth wire complete all as specified incl. taking down old unserviceable sub main wiring and colour coding of cables such as Phase - Red, Neutral – Black, and Earth – Green complete all as directed by Engineer-in-Charge PVC conduit: Make -Polycab/Precision/Plaza Note : (i). One run of conduit two run of 6 Sqmm copper conductor & One run of 6.0 Sqmm coper conductor is measured as one unit (ii). On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit and S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete

M&L for sub main wiring concealed with two single core PVC insulated of size 6 sqmm FRLS unsheathed copper conductor 1100 volt grade multistandard and incl drawn through and including non metallic rigid PVC conduit and conduit accessories of 25 mm external dia and conduit FRLS accessories of ISI marks medium grade including 6.0 sqmm FRLS copper wire for earth continuity wire and connected of common earth dolly and making good to the disturbed surface complete. Wire Make-Finolex/V-guard/Polycab/KEI/Havells/Plaza PVC conduit: Make -Polycab/Precision/Plaza Note:-(One run of conduit two run of 6 sq mm copper conductor & one run of 6.0 sq mm copper conductor is measured as one unit (ii) On RCC ceiling/column, false ceiling, AC/Metallic Sheet ceiling wiring done on surface with conduit and

S&F in replacement single pole and neutral enclosure with a two pin and earth socket complete with top and one single pole MCB of 20 Amp 240 volt and making good to the disturbed surface complete Make: Legrand/Cchneider/Indo Asian/Siemens/Havells

S&F sheet metal enclosure double door for MCB DB single pole and neutral 8 way with 200 Amps, 240 volts double door (Metallic) type Make- Legrand/Hager/Schneider/ndoAsian/Siemens

S&F sheet metal enclosure double door for MCB DB single pole and neutral 4 way with 200 Amps, 240 volts double door (Metallic) type Make- Legrand/Hager/Schneider/ndoAsian/Siemens

S&F vertical sheet metal enclosure double door for MCCB DB Triple pole and neutral 4 way, (4+12) with 200 Amps rated bus bar 440 volts earth dolly IP-43, IK09, and making good to the disturbed surface complete

S&F MCB SP 8 to 32 Amps rating 240 volts C curve, 10 KA, 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to SitEC-60898-1 Make-As approved Make of DB

S&F MCB SPN 40 to 63 Amps rating 240 volts C curve 10 KA 50 Hz, of poles and current carrying capacity in the MCB DB complete with connection testing and commissioning confirming to IS/IEC-60898-1. Make As approved Make of DB

S&F MCCB 4 pole 63 Amp, 440 volt 'C' series, 16 KA, 50 Hz, confirming to IS/IEC-60898-1 Make-As approved Make of DB

Supply and fixing LED 4 batten light 18/20 Watt 230 Volt, complete connection with PVC insulated multi stranded copper flexible wire twin core of suitable size from nearest source complete all as specified and as directed by Engineer-in-Charge Make Havells/Surya/Crompton/Philips/Baial

Supply and fixing complete LED light fittings mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver, holder and LED tube light including connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete Make Havells/Surya/CG/Phillips

Material and Labour for earthing complete with galvanized steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground( earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized iron earth lead 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all fSSR PtIincluding necessary excavation and earth work PCC (1:3:6) type C-1 with 50 mm thick cast RCC ( 1:2:4) type B-1 cover slab framed with 50X30X4 mm MS angle (reinforced with 6 mm dia defomed bar @ 15 cm CIC both ways and suitable handle of 10 mm dia round bar) including providing horenal or coke and magnesium sulphate in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (medium grade) wire mesh conner luas. complete in all respect., GI earth wire protected by 15 mm bore (light grade) galvanized iron pipe and other end connected to the earth bar (test point) made of MS flat (40OX32X6 mm) bend in D shape and fixed to wall by means of fast nut or bolt grouted in to wall at 1 mntr from plinth height. 4sgmm PVC insulated (colour green) copper conductor single run as earth continuity conductor along with 15 mm PVC conduit grouted in wall or fixed on wall surface to be continued up to main switch board and fix with common earth dolly as directed by EIC. Disposal of soil to a distance not exceeding 50 mtr and necessary A/U 5 Each as shown in electrical plate e testing on completion complete all as specified and as directed. 23.00 Supply and fixing in repair of wooden doors with hinges and paint with colour as existing on Meter box/ DB Each Job Box complete all as specified and directed. 24.00 Supply and fixing LED Inverter Lamp Make : Shakti Cat Part No -SZBLB22009 - iBB 9W B22 or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti 25.00 Supply and foxing Inverter Batten T/L fiting Make: Shakti Cat Part No - SZSLBMX018-iBB 18W 4 ft or equivalent complete all as specified and directed. Make: Havells/ Philips/Surya /Crompton/Halonix/ Shakti

Supply and foing in repair of wooden doors with hinges and paint with colour as existing on Meter box DB Bos complete af as specified and directed

Supply and fixing LED Inverter Lamp Make Shakti Cat Part No-SZBLB22009-BB 9W B22 or equivalent and directed: Maka: Havelis/ Philips/Surya/Crompton/lalonix/ Shakt complete all as specified and

Supply and fang Inverter Batten T/L fitting Make Shakti Cat Part No SZSLBMX018-1BB 18V 4 It or equivalent complete all as specified and directed Make: Havells/ Philips/Surya/Crompton/Halonix/Shakti

Note :- Debris obtained from all items should be removed in low lying areas as directed by Engr-in-charge out of MOD Land. (Rates quoted for items are deemed to be included for this, where removal of debris in the items is not considered.)

M/S SACHENDRA KUMAR JAIN (BID ID -3315841)

HARNAM SINGH ANIL SINGH (BID ID -3315734)

M/s Indu Enterprises (BID ID -3315871)

M/s Dinesh Kumar (BID ID -3316040)

MS SHUBHAM SANTOSH JAIN (BID ID -3315812)

RAHUL ASSOCIATES (BID ID -3316271)