WELCOME MAINT AND CERTAIN OTHER MISC B R AND E M WORKS IN OFFRS MD ACCN AT KLP AREA UNDER AGE BR II OF GE SUKNA

Amount

M & L for plain Cement Concrete Type B0 1:2:4 (using 12.5 mm graded stone aggregate) in roof kerbs, rounded or chamfered on haunching in chajjas to prevent water seepage into brick walls, including necessory formwork (upto height of 8 mtr) rounded or chamfered on edges complete all as specified and directed.

M&L PCC 1:2:4 type B-1 (using 12.5 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M&L for Precast Reinforced Cement concrete 1:2:4 type B0 (Using 12.5 mm graded stone aggregate) in 25 mm thick (measured solid) Jallies or louvers including all mouldings set jointed in CM 1:4 but excluding frame including demolition of existing cement concrete complete all as specified and directed.

M & L for providing Reinforced cement concrete (1:2:4) type B-1 Nominal Mix using 20 mm graded stone aggregate as in slab supported on walls ,beams and coloumns in floors,roofs,landings, kitchen slabs etc complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

M & L for providing Reinforced cement concrete (1:1.5:3) A-1 Nominal Mix using 20 mm graded stone aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span and like complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

Supply only integral water proofing compound complete all as specified.

M&L for filling the gaps at the junction of roof sheet and vertical wall any thickness, any position and on height upto 10 m form GL using cement concrete type C1 1:3:6 (using 20 mm graded aggregate) and finish both side of wall by 15 mm rendering in cement mortar 1:6 and applying two coats of cement base paint to match with existing surface to match as specified and directed.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed .

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like laid over and including screed bed 15 mm thick in CM 1:4 and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L 18 to 20 mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12 mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and complete all as specified and directed.

M&L for rough finished flat formwork to soffits of suspended slabs such as roof slabs, floor slabs and similar work not exc. 200 mm thick (horizontal or sloping) work as rough finished surfaces of concrete complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F Second class hard wood plain fillets square, rectangular or triangular in section, wrought secured with screws, cross sectional area exceeding 6 Sq. cm and not exceeding 13 Sq. Cm complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S & F 30 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. size of members of shutters as specified in SSR Part-1, section 8, clause 8.24 (a) kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

S&F 30 mm thick flush shutters, solid core construction, with MDF board and both face is covered with decorative face veneer with 6mm thick teak wood lipping/ frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down and refixing in the same opening shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each including easing and adjusting and also refixing builders hardware as required including renewal of unserviceable screws, etc complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 5 mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 125mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanized mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F Continuous (Piano) hinges, mild steel, bright finished or electro galvanized, width of flaps (When open) 30 mm complete all as specified and directed.

S & F in repair MS Helical door spring 150 mm size including roller and roller plate fixed to wooden or steel frames with welding etc complete all as specified and directed.

S & F 300 mm long ordinary rat tail pattern springs including roller and roller plate complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F in repairs mortice locks suitable for aluminium door of 100 mm size 4 lever aluminium body vertical type as per existing or sample complete all as specified and directed.

S&F in repairs Hasp and staple 100 mm safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and as directed.

S&F in repairs 28 mm dia harrison rail, mild steel, chromium plated with fixing brackets, stops, rollers etc with two Nos of socket, end caps and brackets (decorative type) complete for window opening complete all as specified and directed.

S&F in repair stainless steel towel rail 600 mm long of brass chromium plated fixed with and including chromium plated brass screws and wooden / plastic cleat complete all as specified and directed.

S & F Floor door stopper of brass body and tongue, anodised, with hard drawn steel spring, fixed in floor, Overall length of cover plate 150 mm complete all as specified and directed.

S & F Ball catches with 8 mm dia., steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repair kitchen plate rack made out of 0.63 mm stainless steel sheet & of size not less than 24'' x 30'' x 10'', standard quality fixed with brass screw complete all as specified and as directed.

S & F Rubberised door seal 50 mm width including fixing with nails or adhesive with door complete all as specified and as directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

M&L for mild steel work as in bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; handmade sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F in repairs steel rolling shutters without ball bearing, with thickness of laths 1.00 mm push and pull or mannual type including top cover, anchoring rod, hasp and staple with one shop coat of red oxide or zinc chrome primer and fixed in position in existing opening complete all as specified and directed.

S&F Safety lever locks mild steel with 4 levers including locking plate for rolling shutter complete all as directed.

S&F Ball bearing of suitable sizes complete for rollong shutter complete all as specified and directed.

S&F Powder coated aluminium frame (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

S&F in replacement 4 mm thick E-board (designer pattern) celing of size 60x60 cm, fixed or laid / inserted to with and including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and with and including anodised aluminium snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle with hanging/supporting arrangements hanging from structural steel / scantling with 6 mm GI wire complete all as specified and directed.

S&F 4 mm thick tinted glass of any size with aluminium bedding and complete all as specified and directed.

S&F 4 mm thick frosted / pin headed glass in ventilator shutters complete all as specified and directed.

S&F in repairs 18/19 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screw to timber / aluminium frame work complete all as specified and directed.

S&F 12 mm thick prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in plinth protection/path laid in alternate bays and construction joints to be given at every 3M interval and corners of buildings and filled with bituminous mastic or equivalent filler complete all as specified and directed.

M&L for 75 mm thick cement concrete, type D-2, 1:4:8 (using 40 mm graded stone aggregate) as in path / paving finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 10 mm thick premium quality coloured vitrified ceramic tiles (square / rectangular) polished, area of each tiles n. exc. 0.36 sqm in skirting/dado etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10 mm thick backing in CM 1:4 complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300x 450x 7 mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, as in skirting/dado on vertical surfaces over etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 10 mm thick in CM 1:4 complete all as specified and directed.

M&L cement concrete chequered tiles 300 x 300 x 25 mm thick with grey cement with pigment, set and jointed in neat cement slurry and pointed in coloured cement to match the surfaces as in floors laid over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 fnished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement using WPC compound complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

M&L for rendering 5 mm thick in CM 1:3 on ceiling finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for painting the WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- Applying a thin layer of wall care putty to obtain smooth finish (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the old WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Complete removal of existing old plastered or previously untreated surfaces of wall. (b) Putty application- Applying a thin layer of wall care putty to achieve smooth surface after sanding. (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the NEW CEILING surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the old WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preperation of old plastered or previously untreated surfaces of wall. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of oil bound distemper.

M & L for painting the OLD CEILING surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of oil bound distemper.

M & L for painting the OLD CEILING surface complete all as specified and directed as follows :- (a) Surface Preperation- Complete removal of existing old plastered or previously untreated surfaces of ceiling. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the new wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of cement base paint.

M & L for painting the old wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of cement base paint.

M & L for painting the old wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of old plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of plastic emulsion paint.

M & L for painting the old wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Complete removal of existing old plastered or previously untreated surfaces of wall. (b) Putty application- Applying a thin layer of wall care putty to achieve smooth surface after sanding. (c) Priming surface- Applying one coats of cement base primer. (d) Painting- Applying two coats of plastic emulsion paint.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M & L for painting the new wood surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of pink primer (c) Painting- Applying two coat of synthetic enamel paint.

M & L for painting the old wooden surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the old steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the new steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of red oxide primer (c) Painting- Applying two coats of synthetic enamel paint.

Taking up or down 15 mm dia steel tubing and connections, complete all as specified and directed.

Taking up or down 20 mm dia steel tubing and connections, complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

M&L in repairs High dencity polyethylene pipes (HDPE) of pressure rating 6 kgf/cm2 fixed complete to wall,ceiling or floors etc.40 mm bore pipe complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, etc of 500 ltr to 1000 ltr capacity PVC water storage tank without dismantling the tank incl writting the item "Tank Cleaning on ____" indication the date, month & year of cleaning on external wall of tanks walls with synthetic enamel paint all as specified and directed by Engr -in-charge.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repairs pillar tap 15 mm bore,fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without lettered “hot" or “cold” with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore bib tap, two way, fancy type chromium plated, cast copper alloy, with crutch or butterfly handle and wall flange, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S & F in repair 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S & F 15mm bore stop valve/angle valve, cast copper alloy, long shank and cup concealed type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in replacement 20 mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F in repair PVC connections 15 mm size with PTMT nuts, of length 600 mm & suitable for hot water supply complete all as specified and directed.

S&F in repairs swivel shower rose size 125 mm of brass chromium plated any colour (minimum weight 40 gms) for fixing with 15mm dia steel pipe complete all as specified and directed.

S&F in repairs towel ring of PTMT CP fixed with and including Chromium plated brass screws and wooden / plastic cleats (minimum weight 90 gms) complete all as specified and directed.

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof for 100 mm bore of pipe complete all as specified and directed

S&F stack clamps out of 50 mm x 5 mm flat iron and 16 mm dia round iron stays, incl bolts and nuts and securing ends of stays to wall or roof for 75 mm bore of pipe complete all as specified and directed

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed.

S&F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

S&F in repairs soap dish, with metal dish brass chromium plated fixed to plugs complete all as specified and directed.

S&F in repairs sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S&F in repairs vitreous china european water closet pan (pedestal pattern) white in colour with fixing bolts and flush pipe, connection to trap and to flushing cistern and all joints, including plastic water closet seat cover white, closed pattern with flat bottom and cover and mild steel CP hinges complete all as specified and directed.

S&F in repairs vitreous china squatting pan, "Orissa pattern" white, size 580 x 440 mm with integral foot rest, 'P' or 'S' trap and including connection to trap and to flushing pipe including provn of line concrete holding CI anti -syphonage pipe complete all as specified and directed.

S&F in repairs vitreous china wash hand basin white flat back of size not less than 550 x 400 mm with and including PVC waste pipe 32 mm bore, CP waste fitting and cutting for and pinning in ends of brackets etc, complete all as specified and directed.

S&F in repairs PVC low level flushing cistern of 10 litres capacity, valve less, syphonic action type, white body, with inlet ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair brass chromium plated toilet paper holder fixed to walls with chromium plated brass screws complete all as specified and as directed.

S&F in repairs central hole basin mixer, brass, chromium plated, for mixing hot and cold water, with 450 mm Long Braided Hoses, screwed down for 15 mm bore pipe complete all as specified and directed.

S&F in repair 15mm bore dia brass choromium plated 3-in-1 wall mixer for mixing hot & cold water screwed down for iron pipe and fixed Shower arm 15 mm size, 195mm long with bend of 45degree with flange any colour complete all as specified and directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floor and paving not exc. 15 cm thick (Below or above ground level) complete all as specified and directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

Dismantling wall and ceiling boards, partitions of any description or in any position (fibre, pulp, insulation etc.) any thickness, or insulation boards/ slabs/ blankets of any thickness including cover fillets complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails or screws complete all as specified and as directed.

S&F 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof complete all as specified and directed.

M&L for 5mm thick plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as per specified and as directed by Engr-in-charge.

M&L for roof treatment in order of precedence as given below complete all as specified and as directed:- (i) Taking out of existing water proofing treatment and including padding, cleaning the surface using wire brush, brooming down and washing down with water to remove dust etc, and brushing with neat cement slurry @ 3.00 kg of cement per Sqm. (ii) 15 mm thick screed bed in CM 1:4 on surface. (iii) Cleaning of plastered surface and applying one coat of bituminous primer @ 0.40 Ltr / Sqm. (iv) Supply and laying 3 mm (Minimum) thick APP based polymeric membrane of approved manufacturer with weight not less than 3.60 Kg per Sqm, reinforced with non-woven polyester fabric weight not less than 150 gms per Sqm. Polymeric membrane shall be taken to a height of 30 cm (minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. (Cont.)

(v) Applying one coat of water proofing paint with aluminium finish over APP as per manufacturer's instruction. Note :- (a) Bituminous primer shall be "ShaliTex Primer" manufactured by M/s STP Ltd or equivalent in M/s Sika India Pvt Ltd or M/s Fosroc Chemicals or M/s Hindcon chemicals limited or M/s IWL India Limited (b) Laying APP based polymeric membrane shall be done by torch on method as per manufactures instructions. (c) A minimum overlap of 100 mm and 75 mm should be made at the end and sides of the polymeric membrane respectively and all overlaps and joints shall be sealed as per manufacturers instruction.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made..

M&L in replacement point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) connected to common earths dolly incl connected modular items/ fixture like modular metal flush box, base/ cover plates for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 142.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 142.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 142.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per Sl. item No. 142.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

M&L in replacement point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

All as per Sl. item No. 147.00 above but for one 3 / 5 Amps socket outlet point on independent board.

All as per Sl. item No. 147.00 above but for one 3 / 5 Amps socket outlet point on the same board.

All as per Sl. item No. 147.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per item No. 147.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L in replacement concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 2 runs of 6.00 sqmm main wire along with 1 run of 6.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 4 runs of 10.00 sqmm main wire along with 1 run of 10.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano flush type one way, 15 Amps, 240 volt complete all as specified and directed.

S & F Switch piano 5 Amps single pole two way complete all as specified and directed.

S & F Socket outlet 5 Amps 3 pin flush type complete all as specified and as directed.

S & F Socket outlet 15 Amps 3 pin flush type complete all as specified and as directed.

S&F switch socket combination 2 in 1 , 3 pin , 6 and 16 amps flush type complete all as specified and directed.

S&F switch socket combination 5 pin 6 Amp, flush type universal complete all as specified and directed.

S & F Bell push, flush type, 5 Amps single pole complete all as specified and as directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F switch piano modular type two way, 5 Amps independent, 240 volt complete all as specified and directed.

S&F modular type Bell push 6 A , 1 module complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F in repair electronic modular fan regulator, stepped type( 4 step), white 120 W - 2 module complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB TPN 40 to 63 Amp, 10 kA, 240V 'B' curve complete all as specified and as directed.

M&L for Single pole blanking plate for distribution board complete all as specified and directed.

S&F in replacement MCB ,SPN DB, 08 ways double door, Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete including. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down switchgear with Dbcomplete all as specified and as directed

S&F in replacement MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down switchgear with DB complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F angular type lamp holder, PVC/Polycarbonate type with back plate suitable for Led lamp complete all as directed.

S&F in replacement stepped type electronic fan regulator two module, flush type, with 5 step, 450 W, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in replacement Double door TPN DBs 4 Way, of powder coated DB's suitable for MCB's fitted with bus bar, neutral link, earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required including taking down switchgears with DB complete all as specified and directed.

S&F in repair VTPN DB, MCCB incomer,4 ways double door, Metal door ,IP-54 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 160 complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as direct. Make: Cat ref 507750 of Legrend/L&T or equivalent.

S&F MCCB 4 pole 125 Amps breaking capacity 25 KA, Ics = 100% Icu including spreader link complete all as specified and directed.

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 15 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR15WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 18 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- edgeprorddlr18WLED840SG2 or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 24 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR24WLED857S or equivalent Make of Philips / Crompton .

S&F in repair Recessed Mounted Square (2'x2') LED Panel light 36 watt with CRCA powder coated housing & high transmittance Opal diffuser for glare free with Electronic independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- VENUSMOVE2X2PLR36WLED840SWH or equivalent Make of Philips / Crompton .

S & F in replacement Bell buzzer, Ding Dong AC. 230 volts, single pole completed all as specified and directed.

S & F in replacement Bell, AC. 230 volts, single pole completed all as specified and directed.

S & F in replacement Bell multi music type, AC. 230 volts, single pole completed all as specified and directed.

M &L of Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

S&F ventilation fan 200 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F ventilation fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F of wall mounted Air Circular high flow wove ascillating fans 400mm (16 inches) with pull cord control, high speed motor for higher air delivery & ToP protection, 60W, AC single phase, 230V, copper winding complete all as specified & directed. Make : Havells/Usha/Crompton

S&F in repair Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connenction complete all as specified and as directed. Make-Legrend/Anchor or equivalent.

S & F in repairs LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF =0.95, total System Lumens not less than 1100 lm, 6500k CRI = 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed. Make- Havells , Cat No- RUGBYGENXFTS10WLED865SSYMBOPC or equivalent Make of Philips / Crompton .

S & F in repair Surface and wall mounted LED batten 10 watt 2 ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. Make- Havells , Cat NO- LUMILINEPLUSPROBS10WLED865SPCSSIND Or eqivalent Make of Crompton / Philips.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI = 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. Make-Havells,Cat NO- LUMILINEPLUSPROBS20WLED865SPCSSIND Or eqivalent Make of Crompton / Philips.

S & F in repair wall light of single head of with 9 watt LED lamp of base B-22 inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 12W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 15W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 18W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 24W complete all as specified and directed.

Supply and fix in replacement of LED driver for recessed downlight of capacity 36W complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 100mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 175mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 200mm x 150mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 250mm x 200mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 350mm x 300mm x 50mm size complete all as specified and directed.

MS ORIENT ENGINEERING WORKS (BID ID -3371859)

M/S G S ASSOCIATES (BID ID -3372551)

D K SARKAR (BID ID -3372122)

M/S GLORIOUS CONSTRUCTION (BID ID -3372575)

M/s TRIMURTI ASSOCIATE (BID ID -3370722)

Janata Enterprises (BID ID -3371761)

ELECTRO WIR WAY (BID ID -3372224)