Civil, Structural, Water supply, Sanitary, Roadwork, Internal Electrification, and Miscellaneous works for Establishing 1 LLPD Dairy Plant at Sangmai Gaon, Koliapani, Jorhat, Assam

Civil, Structural, Water supply, Sanitary, Roadwork, Internal Electrification, & Miscellaneous works for “Establishing 1 LLPD Dairy Plant” at Sangmai Gaon, Koliapani, Jorhat, Assam

SOQ/BOQ: Civil, Structural, Water supply, Sanitary, Roadwork, Internal Electrification, & Miscellaneous works for “Establishing 1 LLPD Dairy Plant” at Sangmai Gaon, Koliapani, Jorhat, Assam

Supplying, jointing and lowering of 200mm heavy duty MS pipe . The pipe should be of approved make and zinc chromate primer/ paint shall be applied in welding joints Note: Supplying, jointing, and lowering of 200mm heavy-duty MS pipe of approved make with zinc chromate primer/paint applied on welding joints. SITC is included in this item. Pipe shall conform to IS:4270:2001 and include MS sockets as per IS dimensions, welded with MS electrodes to ensure additional strength for lowering into tube well bore. Pipe shall be minimum 8mm thick. Entire pipeline shall be coated with anti-corrosive paint. (210 mm dia. including strainers, if any)

Supplying, fitting and fixing of 200mm dia 6 mm thick MS cap on the top of the pipe including painting

Supplying, fitting and lowering of Centre Guide complete

Supplying & fitting 200mm dia clamp for casing pipe

Shrouding between borehole & well pipe all round , approximately 125mm thick approved quality gravel of size 1.5mm to 3.5mm washed and cleaned , including supplying, washing, cleaning, trasportaion of gravel to site, shrouding etc. complete Note: Gravel size may vary as per requirement.

Developing tubewell on completion with air compressor, sand free clear water and testing yield and drawing out water continuously for 8 hours per day for a minimum period of 3 days (with clean water) , including cost of fuel, hire chrages of pumps, compressors, any other plant, accessories etc. alongwith submission of Yield test report . Water is to be made clean and free from sand and suspended particles etc. complete.

Supply & fixing of GI B class pipe of approved make for distribution of water alongwith accessories like sockets, bends, tees, reducers etc. Note: Size of GI B Class pipe shall be considered as 50 mm dia.

Santiary sealing of annual space between bore and housing pipe with cement slurry

Chemical and bacteriological testing of water and submission of report

Conducting ground water survey by VES technique, identification of potential Bore well points to meet the water requirement & submittal of report based on the data collected.

Providing, fabricating, assembling, fixing and lowering in true vertical plumb 50mm dia. UPVC Sch. 80 column pipe of approved make and lowering submersible pump set in the borewell including all clamps & accessories etc complete as directed.

CASING PIPE Note: Supplying, jointing, and lowering of 160 mm heavy-duty MS pipe of approved make with zinc chromate primer/paint applied on welding joints. SITC is included in this item. Pipe shall conform to IS:4270:2001 and include MS sockets as per IS dimensions, welded with MS electrodes to ensure additional strength for lowering into tube well bore. Pipe shall be minimum 7mm thick. Entire pipeline shall be coated with anti-corrosive paint. Including strainers, if any.

Providing and lowering 200 mm DN Medium well casing pipes (CM) of PVC-U as per Indian Standard (IS) 12818: 2010 with latest amendments / latest edition including suitable fittings etc complete as directed. This item includes providing and fixing fittings for joining casing pipes with simillar or different sized casing/screen pipes if applicable etc complete.

Drilling of borewell of 150mm dia and sinking of tubewell in rocky strata including boulder (by DTH method) suitable for tubewell of size 150mm through all kinds of soils including rocks / boulders as per specification.

Supply & fixing 50mm dia. Integrally-moulded Wafer-type lever operated Butterfly Valve PN 10 pressure rating of Cast Iron body. The valve should provide reliable sealing in water complete in all respect as per functional requirements.

Providing & fixing of suitable metallic wire rope for additional support to the submersible pump for 8mm dia. Wire rope. Note: Bidder to quote for 8 mm dia. Wire rope 7x19.

Drilling (Reaming) 350mm to 500/550mm bore hole in alluvial strata including all labour and consumable charges for assembling, installing and lowering of 250mm dia housing, casing and strainer pipes etc followed by gravel packing/shrouding between borehole & well pipe all round with kapchi (for borewells from 0 meter to 250 meter depth) etc complete as directed.

Providing, installing, lowering and comissioning of electrical motor cum submersible pump sets in 3-phase system and of suitable Horse Power (HP) rating excluding control panel. Measurement shall be recorded in HP. Rate shall be quoted per HP.

Providing and laying machine mixed plain cement concrete (PCC) 1:4:8 in volumetric proportion (1 part of cement:4 part coarse sand : 8 part aggregates of size 37 mm and down) for specified thickness, for foundations below walls, column footings, sunk floor terraces at any height above plinth level raft at any depth below floors, pavements roads, plinth protection, etc. including centring and shuttering if required, laying spreading, ramming, consolidating as per requirement and curing etc. complete as directed. Note: Stone aggregates may be 20mm and down graded or 37mm and down graded for use in PCC. This item shall be paid for structural elements of any shape, size & thickness or depth and also for columns at terrace for future expansion provision, encasing of pipes/services, screed concreting, etc. This item includes shuttering work below highest plinth level till all heights.

Providing and laying machine mixed plain cement concrete (PCC) 1:3:6 with 1 part of cement: 3 parts of coarse sand: 6 parts of stone aggregate of size 37 mm and downgraded for specified thickness, for foundations below walls, column footings, sunk floor terraces at any height above plinth level raft at any depth below floors, pavements roads, plinth protection, etc. including centring and shuttering if required, laying spreading, ramming, consolidating as per requirement and curing etc. complete as directed. Note: Stone aggregates may be 20mm and down graded or 37mm and down graded for use in PCC. This item shall be paid for structural elements of any shape, size & thickness or depth and also for columns at terrace for future expansion provision, encasing of pipes/services, screed concreting, etc. This item includes shuttering work below highest plinth level till all heights.

Providing & laying in position machine mixed and machine vibrated cement concrete of controlled grades for reinforced cement concrete structural elements in any shape, size, thickness or depth and design viz. foundations, columns, beams, slabs, raft, floor plinth beams, plinth beam ledges, window sills, copings, thin band beams, walls parapets boxes, folded plates, chajjas, mullions, retaining walls, fins, staircases, overhead and underground water and other fluid tanks, statically loaded foundation rafts/floor, water troughs, manhole slab, septic tank slab, soak well slab etc. its concrete elements in any shape, size, thickness/depth and design as per structural design and as directed in specified compressive strength compressed in N/mm2 at 28 days as per IS 456-2000 using 20 mm or as specified size of crushed stone aggregates including design of concrete mixes, auto weigh batched proportioning, cost of admixtures, necessary lift and lead as specified, finishing concrete surfaces, curing etc. complete but excluding centring/shuttering and reinforce-ment. The conversion of weigh batching to equivalent volumetric one, if permitted, should be got approved from Engineer before execution. For concrete grade M- 25 below and up to highest plinth level. Note:- Concrete shall be produced in fully automated concrete batching plant having batch reports printing facility for all ingredients of concrete. All the batch reports prints shall be submitted to the site engineer on daily basis and the batch data shall be maintained in a format for further analysis. Minimum Portland Pozzolana Cement (PPC) content for the concrete shall be 370 Kg/CuM.

Providing & laying in position machine mixed and machine vibrated cement concrete of controlled grades for reinforced cement concrete structural elements in any shape, size, thickness or depth and design viz. foundations, columns, beams, slabs, raft, floor plinth beams, plinth beam ledges, window sills, copings, thin band beams, walls parapets boxes, folded plates, chajjas, mullions, retaining walls, fins, staircases, overhead and underground water and other fluid tanks, statically loaded foundation rafts/floor, water troughs, manhole slab, septic tank slab, soak well slab etc. its concrete elements in any shape, size, thickness/depth and design as per structural design and as directed in specified compressive strength compressed in N/mm2 at 28 days as per IS 456-2000 using 20 mm or as specified size of crushed stone aggregates including design of concrete mixes, auto weigh batched proportioning, cost of admixtures, necessary lift and lead as specified, finishing concrete surfaces, curing etc. complete but excluding centring/shuttering and reinforce-ment. The conversion of weigh batching to equivalent volumetric one, if permitted, should be got approved from Engineer before execution. M-30 for RCC structures below and up to highest plinth level. Note:-Concrete shall be produced in fully automated concrete batching plant having batch reports printing facility for all ingredients of concrete. All the batch reports prints shall be submitted to the site engineer on daily basis and the batch data shall be maintained in a format for further analysis. Minimum Portland Pozzolana Cement (PPC) content for the concrete shall be 420 Kg/CuM.

Providing & laying in position machine mixed and machine vibrated cement concrete of controlled grades for reinforced cement concrete structural elements in any shape, size, thickness or depth and design viz. foundations, columns, beams, slabs, raft, floor plinth beams, plinth beam ledges, window sills, copings, thin band beams, walls parapets boxes, folded plates, chajjas, mullions, retaining walls, fins, staircases, overhead and underground water and other fluid tanks, statically loaded foundation rafts/floor, water troughs, manhole slab, septic tank slab, soak well slab etc. its concrete elements in any shape, size, thickness/depth and design as per structural design and as directed in specified compressive strength compressed in N/mm2 at 28 days as per IS 456-2000 using 20 mm or as specified size of crushed stone aggregates including design of concrete mixes, auto weigh batched proportioning, cost of admixtures, necessary lift and lead as specified, finishing concrete surfaces, curing etc. complete but excluding centring/shuttering and reinforce-ment. The conversion of weigh batching to equivalent volumetric one, if permitted, should be got approved from Engineer before execution. For concrete grade M- 25 to all height from highest plinth level. Note:-Concrete shall be produced in fully automated concrete batching plant having batch reports printing facility for all ingredients of concrete. All the batch reports prints shall be submitted to the site engineer on daily basis and the batch data shall be maintained in a format for further analysis. Minimum Portland Pozzolana Cement (PPC) content for the concrete shall be 370 Kg/CuM.

Providing & laying in position machine mixed and machine vibrated cement concrete of controlled grades for reinforced cement concrete structural elements in any shape, size, thickness or depth and design viz. foundations, columns, beams, slabs, raft, floor plinth beams, plinth beam ledges, window sills, copings, thin band beams, walls parapets boxes, folded plates, chajjas, mullions, retaining walls, fins, staircases, overhead and underground water and other fluid tanks, statically loaded foundation rafts/floor, water troughs, manhole slab, septic tank slab, soak well slab etc. its concrete elements in any shape, size, thickness/depth and design as per structural design and as directed in specified compressive strength compressed in N/mm2 at 28 days as per IS 456-2000 using 20 mm or as specified size of crushed stone aggregates including design of concrete mixes, auto weigh batched proportioning, cost of admixtures, necessary lift and lead as specified, finishing concrete surfaces, curing etc. complete but excluding centring/shuttering and reinforce-ment. The conversion of weigh batching to equivalent volumetric one, if permitted, should be got approved from Engineer before execution. M-30 for RCC structures to all height from highest plinth level. Note:-Concrete shall be produced in fully automated concrete batching plant having batch reports printing facility for all ingredients of concrete. All the batch reports prints shall be submitted to the site engineer on daily basis and the batch data shall be maintained in a format for further analysis. Minimum Portland Pozzolana Cement (PPC) content for the concrete shall be 420 Kg/CuM.

Providing and erecting in position form work shuttering & boxing using steel/plywood shuttering materials of approved quality for concrete elements vertical, horizontal, inclined, circular, curved etc. in all sizes, shapes and designs as per drawing including necessary staging at all intermediate levels, scaffolding, bolts/nuts, fastener nails, wires for keeping in position till concrete is laid and members have acquired required strength, removal thereafter, applying shuttering oil etc. complete as directed. At all levels below ground level and up to highest plinth level for all concrete elements of any shape, size & direction etc complete as directed. Note:-Approved quality of new plywood and new metal plates/sheets shall be used for shuttering and form works. Subsequent repetitions for shuttering are allowed only till they are in good condition as per the decision of engineer/site engineer.

Providing and erecting in position form work shuttering & boxing using steel/plywood shuttering materials of approved quality for concrete elements vertical, horizontal, inclined, circular, curved etc. in all sizes, shapes and designs as per drawing including necessary staging at all intermediate levels, scaffolding, bolts/nuts, fastener nails, wires for keeping in position till concrete is laid and members have acquired required strength, removal thereafter, applying shuttering oil etc. complete as directed. Form Work in superstructure to all heights above highest plinth level for all concrete elements of any shape, size & direction etc complete as directed. Note:-The item includes staging/false staging as applicable and if required at all intermediate levels for all heights. Approved quality of new plywood and new metal plates/sheets shall be used for shuttering and form works. Subsequent repetitions for shuttering are allowed only till they are in good condition as per the decision of engineer/site engineer.

Supplying and mixing with cement for cement concrete/cement mortar, integral water proofing compound approved make & quality as per the requirements and manufacturer’s specifications etc. complete as directed.

Providing and Grouting the foundation bolts/pockets, base plates with ACC Shrinkkomp grade-2/ GP2 of FOSROC or FLOWGROUT 60 of FAIRMATE ready mixed non shrink, free flow, self levelling, cementitious grout making holes if necessary in concrete, curing etc. as per the recommendations of the manufacturer, complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 8 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 10 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 12 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 16 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 20 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and Fixing of reinforcement steel dowel bar in the existing RCC elements by re-bar method including machine drilling (minimum drilling hole dia. shall be 1.5 times of the dia. of dowel bar to be inserted and up to suitable inset depth as directed), supply of necessary anchoring chemicals such as epoxy based resin and hardener of approved make like HILTI India or equivalent approved and work to be carried through the competent agency including all materials, labours, tools, etc complete as directed for 25 mm dia bars. (Reinforcement shall be paid under relevant item of this tender), complete as directed.

Providing and laying machine mixed, vibrated in controlled cement concrete of grade M25 with 20 mm and down grade aggregates for machine / equipment foundation of any shape, size & design; including necessary centering / shuttering,staging, providing and making necessary pockets of required size and shape (by providing moulds of required shape & size), fixing insert plates / pipes etc. in line, level and plumb complete as per drawing and grouting the same with non-shrink cementitious free flowing grout and finishing, curing but excluding reinforcement steel etc. complete as directed. (note : measurement for grout and Reinforcement steel/ insert plate will be paid separately as per relevant item )

Providing and applying concrete bonding compound of approved or equivalent make to old / new concrete surfaces at all levels, in vertical and horizontal planes as directed by engineer after necessary chipping & cleaning surface dust free.

Providing and laying machine mixed Plain cement concrete (PCC) in volumetric proportion 1:5:10 (1 part of cement:5 part coarse sand:10 part Coarse aggregates of size 37 mm and down) for specified thickness, for foundations below walls, column footings, sunk floor terraces at any height above plinth level raft at any depth below floors, pavements roads, plinth protection, etc. including centring and shuttering if required, laying spreading, ramming, consolidating as per requirement and curing etc. complete as directed. Note: Stone aggregates may be 20mm and down graded or 37mm and down graded for use in PCC. This item shall be paid for structural elements of any shape, size & thickness or depth and also for columns at terrace for future expansion provision, encasing of pipes/services, screed concreting, etc. This item includes shuttering work below highest plinth level till all heights.

Providing and fixing Anchor Fastener approved make including drilling of hole in frame, concrete/ masonry etc. complete as per manufacturers specification & direction of Engineer In-charge for 10 mm Dia Note:-Anchore fastener shall be of Galvanised Carbon Steel.

Providing and fixing Anchor Fastener approved make including drilling of hole in frame, concrete/ masonry etc. complete as per manufacturers specification & direction of Engineer In-charge for 12 mm Dia Note:-Anchore fastener shall be of Galvanised Carbon Steel.

Providing and fixing Anchor Fastener approved make including drilling of hole in frame, concrete/ masonry etc. complete as per manufacturers specification & direction of Engineer In-charge for 16 mm Dia Note:-Anchore fastener shall be of Galvanised Carbon Steel.

Providing and fixing Anchor Fastener of approved make including drilling of hole in frame, concrete/ masonry etc. complete as per manufacturers specification & direction of Engineer In-charge for 20 mm Dia Note:-Anchore fastener shall be of Galvanised Carbon Steel.

Providing and fixing Anchor Fastener of approved make including drilling of hole in frame, concrete/ masonry etc. complete as per manufacturers specification & direction of Engineer In-charge for 25 mm Dia Note:-Anchore fastener shall be of Galvanised Carbon Steel.

Providing and placing in position 25mm thick approved make polyethylene joint filler board cross linked, non-absorbent, semi rigid and cellular for forming expansion joints in concrete, brickwork and block work. This board shall be placed in locations before concreting as per drawing or as instructed by the Engineer in the expansion and construction joints in the required size and shape. The work shall be done at all levels without any extra cost. It shall be measured in Sq.M. Wastage shall not be considered for payment.

Providing and fixing Precast concrete slab perforated type for shelves, ledges, trench / pit / chamber covers/gutter covers (50 to 150 mm thick) etc. as per drawing in controlled concrete of grade M-25 , to cast, cure, hoisting, fixing in position including necessary form work (providing exposed concrete finish for visible faces), grouting holes / grooves, inserts, projections, providing and fixing lifting hooks using MS rounds etc. grouting and pointing of joints finishing neat etc. complete but excluding reinforce-ment steel etc complete as per the drawing and as directed. (Refer Item no. 2.12 of Section IV for detailed specifications)

Providing and fixing of concrete compound wall having height of minimum 2.1 metres made with precast pre-stressed reinforced cement concrete posts having 8 nos, 4mm dia GI wires as reinforcement steel and of M 35 grade of concrete as per following details. (1) Excavation in any type of soil for foundation pits of minimum size (500mm x 500mm x minimum 800mm deep) including filling the excavated earth as directed followed by compaction (2) Laying of Plain cement concrete (1:2:3 proportion) for pits (500mmX500mmX minimum 800mm) for erection of pre-stressed RCC posts. The spacing of RCC posts shall be according to the length of concrete panel/plank (3) Providing and fixing in line level & plumb the Pre-cast RCC post of M-35 grade concrete of size (2950 mm long x 150 mm wide x 150 mm thick having grooves for the provision of tightly fixing the pre-cast pre-stressed concrete wall panels/planks) as per requirement & details including provision for fixing of MS angle posts for fixing wire fencing over it etc. (4) Providing and fixing pre cast planks(panels) of pre-stressed Cement concrete of M-30 grade of size (2100 mm long x 300 mm wide x 38 to40 mm thick) and having three nos. 4mm dia GI wires as reinforcement steel in line, level & plumb including filling joints with cement slurry or as per the recommendations of manufacturer etc completed as per the drawings and as directed. The item includes excavation, concrete and all the pre-stressed concrete works including labour cost etc complete. Note : The excavation in any type of soil/rock for foundation pits is included in this item.

Providing and constructing brick masonry in any shape in Cement Mortar (CM) 1:6 (1 part cement and 6 part coarse sand) in all works with approved quality bricks having minimum crushing strength 40 Kg./Sq.cm including all necessary scaffolding, racking out the joints, curing etc. complete as directed - In foundation at all levels below and up to highest plinth level.

Providing and constructing brick masonry in any shape in Cement Mortar (CM) 1:6 (1 part cement and 6 part coarse sand) in all works with approved quality bricks having minimum crushing strength 40 Kg./Sq.cm including all necessary scaffolding, racking out the joints, curing etc. complete as directed - For providing and constructing Brick masonry in superstructure at all heights above highest plinth level

Providing and constructing 115 mm thick brick masonry in partition with approved quality bricks having minimum crushing strength 40 Kg./Sq.cm, at all levels in CM 1:4 (1 part cement and 4 part coarse sand) including scaffolding, racking out joints, reinforcement of 2 Nos. 6 mm dia bars at every fourth course or 25 mm x 1.2 mm iron hoop in every 3rd course, curing, etc. complete as directed. (Rate includes the cost of MS bars or iron hoop).

Providing Fly ash bricks masonry work using (230 /250 mm x 115/125 mm x 75 mm size) with minimum Crushing strength of 50 kg./sqcm. in cement mortar (1:6). Immersing the bricks in water before use in all type of massonary works in English / Flemish and other type of bonds for walls ,pillars, projections, splays cutting, circular molding for corbelling, trenches, septic tank ,Soak well,storm water channel,chambers, etc. with racking out the joints .The rates Including cost of conveyance, taxes & royalties , loading & unloading of all materials & cost of all Labours ,scaffolding, watering & curing for seven days, T.& P. etc .complete as per the direction of Engineer- in- charge. ( Note : No holes for scaffolding will be permitted into the brickwork.) In foundation at all levels below and up to highest plinth level.

Providing Fly ash bricks masonry work using (230 /250 mm x 115/125 mm x 75 mm size) with minimum Crushing strength of 50 kg./sqcm. in cement mortar (1:6). Immersing the bricks in water before use in all type of massonary works in English / Flemish and other type of bonds for walls ,pillars, projections, splays cutting, circular molding for corbelling, trenches, septic tank ,Soak well,storm water channel,chambers, etc. with racking out the joints .The rates Including cost of conveyance, taxes & royalties , loading & unloading of all materials & cost of all Labours ,scaffolding, watering & curing for seven days, T.& P. etc complete as per the direction of Engineer- in- charge. ( Note : No holes for scaffolding will be permitted into the brickwork.) - In superstructure at all heights above highest plinth level .

Providing and constructing 125 mm thick Fly Ash brick masonry in partition as per detailed drawing at all levels in CM 1:4 (1 part cement and 4 part coarse sand) including RCC patli / stiffeners of size 125mmx75mm of mix 1 : 2 : 4 concrete reinforced with pair of 6mm dia MS bars laid at every 3rd course height including scaffolding, racking out joints, curing etc. in line, level and plumb, All complete as per specification for all height of floor or as directed etc. (Rate includes the cost of MS bars or iron hoop). (No holes for scaffolding will be permitted into the brickwork)

Providing & constructing 230mm thick random rubble pitching un-coursed, of granite or approved quality quarry dressed stones in cement mortar 1:6 (1 part of cement:6 part of coarse sand) in jointing / pointing, including dressing, breaking the clods if any, uniformly levelling the slope , ramming & watering the subgrade, wetting the stones before use, hammering down with wooden mallet for positioning the stones uniformly, forming face joints not more than 25mm thick, racking of joints up to 20mm deep during construction for the purpose of plastering / pointing , curing for 10 days etc., all complete as per drawing and direction of EIC. In foundation at all levels below and up to highest plinth level

Extra for providing & making vision panel in flush door shutter/TW shutter including TW lipping, beading and painting / polishing matching to the finish of the shutter etc complete as directed.

Providing and fixing cupboard below platform with SALWOOD frame 75 mm x 37 mm fixed with 2 nos. MS hold fasts of size 20x3 x150 mm long on each vertical side to be grouted in PCC 1:2:4 or fixing with coach bolts, 19 mm thick pre- laminated/ commercial board shutter of approved make with T.W lipping , including one shelf of similar material with its supporting, Aluminium anodised / powder coated fittings and fixtures , 2 or more coats of first quality synthetic enamel paint over a coat of wood primer or flat paint or polish of required shade etc. complete as directed. Note:-Fittings and fixtures shall be of approved make stainless steel grade 304 in place of Aluminium.

Providing and fixing flush door shutter of 37 mm (total thickness) with 1 mm thick lamination on both side of approved make and quality thermosetting synthetic resin bond solid batten core with 10 mm thick lipping of first quality teak wood batten on all edges with Aluminum anodized / powder coated fixtures and fittings such as tower bolts, handles, aldrops, door stopper, hinges etc. as per details, of approved make, including 2 or more coat of first quality synthetic enamel paint of approved make & shade , over a coat of wood primer ,or flat paint or polish of required shade etc. all complete as directed

P/F Satin stainless steel grade 316 pull handle of approved or equivalent make, including the cost of screw and other incidental charges complete. For size 200 mm

Providing and fixing Satin Stainless steel finish grade 316 floor mounted door stopper approved or equivalent make, including the cost of screw and other incidental charges complete.

Providing and fixing Satin SS finish stainless steel grade 304 tower bolt of approved or equivalent make, including the cost of screw and other incidental charges complete For size 250mm x 12 mm.

Providing and fixing on aluminium/Flush door Satin stainless steel finish grade 316 of approved or equivalent make lock with half cylinder one side key of equivalent make as approved including the cost of screws etc. complete.

Providing and fixing IS : 3564 marked aluminium extruded section body tubular type universal hydraulic door closer with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing With float glass panes of 5.50 mm thickness glazing (with float glass panes of 5.50 mm thickness) in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid separately against the respective item)

Providing & fixing 12 mm thick Hilux Calcium Silicate Board Water resistant, Non Combustible, (As Per BS Standard, Certified by CBRI Roorkee) Termite & Vermin proof, Eco- Friendly of approved or equivalent make in Aluminium door, window, ventilator, partition or similar such other location so called for with PVC / Neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading / aluminium channel shall be paid separately )

Providing and fixing powder coated anodized aluminium (anodised transparent or dyed to required shade according to IS:1868, Minimum anodic coating of Grade AC 25) (minimum thickness of powder coating 50 micron ) frame works for doors, windows, ventilators and partitions with extruded built-up standard tubular sections / appropriate Z and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with rawl plugs and screws or fixing clips, or with expansion hold-fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/Neoprene felt, Silicon sealant of approved make etc. Aluminium sections shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, CP Brass/ stainless steel screws, all complete as per architectural drawings and as directed (Cost of glazing / paneling shall be paid separately as per the respective items). Note:-Aluminium extruded sections for door shutters, window shutters (sliding, casement, folded, side hung, top hung or other etc all types of windows/ventilators) louvers, partitions, snap beading, U beading, Channels etc etc all are also incudes under this item. The sliding arrangement for door/windows etc. through rollers, pivots or any other fitments are also included under the item. EPDM rubber gasket etc. are also included under the item. Only the aluminium sections shall be measured for payment in Kg. Cost of all other materials, consumables etc. as above is deemed/considered as included.

Providing and fixing Stainless Steel ( SS 304 grade ) adjustable friction windows stays of approved quality with necessary stainless steel screws etc. to the side hung windows as per direction of Engineer-in-charge complete .For size 355 mm X 19 mm

Providing and fixing Satin Stainless steel finish grade 316 mortice lock consisting of lock cylinder with half cylinder one side key and handles of approved or equivalent make, including the cost of screw and other incidental charges complete.

Providing and fixing fly proof S.S. wire mesh to window shutters with aluminium beading (which will be paid separately under respective aluminium item).

Providing & Fixing 4mm thick Compact sheet in aluminium door and partitions. Compact sheet shall be made from solid grade compact High Pressure Laminate manufactured under high pressure and temperature with bunch of kraft papers and decorative papers including approved quality PVC/ neoprene gasket etc complete as directed. (Cost of aluminium snap beading and aluminum sections shall be paid separately against the respective item)

Providing and fixing concealed lock in sliding windows of approved make & shade as directed.

Providing and fixing Aldrop of Stainless Steel (SS) 316 grade and of approved size and make including all the fixing accessories as per the recommendations of manufacturer etc complete as directed. Note: Aldrop size shall be 10 inch.

Providing & fixing Stainless Steel Hinge 304 grade Satin finish butt hinges of sizes 125x75x3mm with 4 Nos. Ball Bearing of approve make , including necessary screws etc. complete as directed by Engineer In charge.

Providing & Fixing decorative 1.0 mm thick high pressure laminated sheet of plain/wood grain in gloss/matt/suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046, Type S, including cost of adhesive of approved quality etc complete as directed.

Providing and fixing minimum 6mm thick toughened glass glazing in aluminium door, window, ventilator shutters, partitions, louvers and vision panels etc with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item of aluminium section in Kg under this contract) etc complete as directed.

Providing and fixing satin stainless steel grade 304 pull handle of approved quality including the necessary stainless steel screws and other incidental charges complete as per detailed Architectural Drawings etc complete as directed by Engineer-in-charge. Handles shall be of 22 mm dia x 300 mm long A pair of two handles shall be considered as one Set.

Providing and fixing stainless steel grade 304 brush/satin finish tower bolts including the necessary Stainless steel screws and other incidental charges complete as per detailed Architectural Drawings and as directed by Engineer-in-charge. Tower bolt shall be of 150 mm long Note:- Manufacturer's warranty/guarantee card shall be submitted. Make : Dorma : TGDI-D 300. Hafle:- 903.05.700 Kich PRDH2212S.

Providing and fixing stainless steel grade 304 brush/satin finish tower bolts including the necessary Stainless steel screws and other incidental charges complete as per detailed Architectural Drawings and as directed by Engineer-in-charge. Tower bolt shall be of 300 mm long. Note:-Manufacturer's warranty/guarantee card shall be submitted. Dorma :3200-2, Hafle 911.81.080 Kich TBF36S

Providing and fixing Satin stainless steel Foot operated Door Stopper with rubber buffer of approved quality with necessary SS screws etc. all complete as per detailed Architectural Drawings and as directed by Engineer-in-charge : Note:-Manufacturer's warranty/guarantee card shall be submitted. Dorma : 3200, Hafle 911.81.083 Kich TBF312S.

Providing and fixing Satin stainless steel wall mounted Door Stopper with rubber buffer of approved quality with necessary SS screws etc. all complete as per detailed Architectural Drawings and as directed by Engineer-in-charge : Note:-Manufacturer's warranty/guarantee card shall be submitted. Dorma : 4016 Hafele 938.04.101 Kich DSTRS.

Providing and installing in position frameless glass partition / frameless glazing with Laminated glass of approved quality of 11.72 mm overall thickness with 1.72mm thick polyvinyl butyral sandwiched between 5 mm thick clear toughened glass & 5 mm thick clear toughened glass of Saint gobain or equivalent using SS finish Wall Connecting Profile (WCP of size 40mmX 12mm) base rail with fixing holes including clamping parts with screws and gasket for 11.72 mm glass with cover profile on both sides, as per design & approved shop drawings including filling the joints with Silicon sealant structural grade and weathering grade of Dow corning - USA or "GE Silicon - USA" or "WACKER - Germany"., complete as per detailed drawings & approved shop drawings. (Installed glass area shall be measured). ( Dormakaba / BENE / maars /Gaze )

Providing and fixing double action hydraulic floor spring of approved brand/make and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. With stainless steel cover plate minimum 1.25 mm thickness

Extra for providing process charges of frosting the glass (any thickness of glass and for any pattern ) as per drawing and as directed by engineer in charge. Sample shall be approved before execution.

P&F FROSTED FILM ON GLASS PARTITION/DOOR

Providng and Fixing Wooden-Plastic Composite (WPC) door specifications typically include thicknesses of Min. 40mm, materials like PVC, wood flour, and additives, and properties like 100% water and termite-proof. Typical WPC Door shall be in a combination of wood fibers or flour and thermoplastic polymers such as PVC, PE, or PP, along with various additives. Water & Moisture Resistance: WPC doors are 100% waterproof and resistant to moisture, making them ideal for high-humidity areas like Dairy Plant & bathrooms. Door shall be completely termite-proof and borer-proof. Fire Resistance, Workability shall be Suitable for cutting, routing, polishing, and screwing. Finish Options to be in plain, textured, CNC, laminated, or veneer finishes, often with wooden color options as approved by Engineer -In- Charge.

Providing and applying 12 mm thick plain cement plaster finish at all heights and below highest plinth level in Cement Mortar (CM) 1:4 (1 part cement: 4 parts sand- 50% coarse and 50% fine) in line, level and plumb to the walls, concrete elements, beams, ceiling, stair, columns, pardis, including making plaster bands, stripes, moulds, pattas, grooves etc, over any brick or concrete surface as specified including scaffolding, curing and finishing smooth, complete as directed. Note:-Item includes for all shapes.

Providing and applying 19 mm thick plain cement plaster finish in two layers with first coat of 12mm thick with Cement Mortar (CM) 1:4 (1 part cement: 4 parts sand- 50% coarse and 50% fine) in line, level and plumb and second coat of 7 mm thick with CM (1:2) (1 part cement : 2 part fine sand) to the walls, concrete elements, beams, ceiling, stair, columns, pardis, including making plaster bands, stripes, moulds, pattas, grooves etc, over any brick or concrete surface as specified including scaffolding, curing and finishing smooth, complete as directed at all heights and below highest plinth level. Note:-Item includes for all shapes.

Providing and applying 19 mm thick sand faced cement plaster in two coats at all heights below and above highest plinth level with first coat of 12 mm thickness with cement mortar 1:4 (1part cement: 4 part of coarse sand) and top coat of 7 mm thickness with cement mortar 1:3 (1part cement: 3 parts of coarse sand) finishing using sponge to give uniform finish, on all types of concrete/brick surfaces including making plaster bands, stripes, pattas, grooves, drip moulds as per drawing/details, including scaffolding, curing etc., complete as directed. Note:-Measurement shall be for plain area without consideration of co-efficient for sand faced surfaces. Item includes for all shapes.

Providing and applying 25 mm thick water proof cement plaster in two layers of 15 mm under layer and 10 mm thick top layer both in C M 1: 3 (1 part cement: 3 part sand -50% coarse and 50% fine) in line, level and plumb at all heights below and above highest plinth level, including adding water proofing compound of approved quality and make as per manufacturer’s specifications necessary scaffolding curing etc complete as directed. (Quantity of waterproofing admixture added, shall be measured and paid for under relevant item).

Providing and applying ( with brush only) white washing with lime on new /old work, at all heights below and above highest plinth level , three or more coats to give an even shade to walls, ceiling, AC sheets, etc., including addition of glue of approved make, Indigo (blue) to give bright finishing including scaffolding etc. complete as directed.

Providing and applying plastic emulsion paint of approved make and desired shade , on new / old work including the preparation of surface for painting, applying primer and putty, rubbing the surface, again applying primer, applying plastic paint in two or more coats to give an even shade , at all heights below and above highest plinth level, scaffolding etc complete as per manufacturer’s specifications and as directed. Note:-Putty shall be applied in two or more coats and for minimum average 1mm thick to get even surfaces.

Providing and applying 15 mm thick plain cement plaster finish at all heights and below highest plinth level in Cement Mortar (CM) 1:3 (1 part cement: 3 parts sand- 50% coarse and 50% fine) over chicken wire mesh to cover Insulated Surface in line, level and plumb to the walls, concrete elements, beams, ceiling, stair, columns, pardis, including making plaster bands, stripes, moulds, pattas, grooves etc, over any brick or concrete surface as specified including scaffolding, curing and finishing smooth, complete as directed. Note:-Item includes for all shapes.

Providing and applying acrylic based Anti fungus exterior paint of approved make of desired shade on new work of smooth / sand faced / rough cast plaster finish.. Preparation of surface to be painted should be free from dust, grease any growth of fungus, algea or moss needs to be removed thoroughly by vigorous wire brushing and washing the surface with water, Freshly plastered surface to be allowed to cure completely. In case of surface imperfections such as holes, dent and cracks are to be filled only by using mixture of white cement and fine sand in the ratio of 1 : 3 at no extra cost (note - Any kind of putty is not recommended) for painting, applying primer of approved make, applying 2 coats of approved make paint as per specification at all heights below and above highest plinth level, scaffolding etc. complete as directed. (Measurement to be of the treated surface & nothing extra for rough / sand face surface) Note:-Paint shall be Apex Ultima Protek or equivalent approved make. Measurements shall be for plain area without consideration of multiplying co-efficient for sand faced surface or any other textured, wrinkled or other special surfaces.

Providing and applying 6 mm thick plain cement plaster finish at all heights and below highest plinth level in Cement Mortar (CM) 1:3 (1 part cement: 3 parts sand- 50% coarse and 50% fine) to the beams, ceiling, pardis, bends, moulds, pattas grooves etc, over any brick or concrete surface as specified including scaffolding, curing and finishing smooth, complete as directed.

Providing & fixing Glass fibre reinforced concrete "Jali" as a sun protector in position within brick or RCC opening. These jalis shall be fixed with S.S. Screw, fixture plug, anchor fastener bolt, MS Clamp, SDST bolt (self-tapping bolt/screw) as per requirement on MS fabrication/Wall/R.C.C and finished all joints with White cement/white putty/Epoxy Grout/Silica sand. Provide light reinforcement bars between two jalis (within cement mortar). GRC material shall be UV stabilized, durable & should withstand extreme weather condition, fire retardant, water repellent, etc. GRC jalis shall be made as per design provided by the Architect. Prototype of jali shall be made & get approved from Architect. The rate shall be including fixing of grill, transportation, scaffolding. Rate of MS bars and MS Fabrication work shall be paid under relevant item. Curtain wall made from these jalis shall be in true line & level & plumb.

Providing & Fixing of Lay-in Tile Perforated False Ceiling on 15 mm ‘T’ Framework/ 15mm Silhouette Grid/frame work of module 600mm x 600mm made out of 0.7mm thick Aluminium Alloy 3105 with Non-woven felt made of glass-reinforced fibre glued over the perforation for sound absorption. The perforations shall be 2.5mm dia 5.5mm c/c. The Tile shall be Polyester based, powder coated & colour as sugessted by Architect. Grid system for fixing ceiling tiles shall comprise of Tees. The 15 mm main tee runners shall be suspended at an interval of 1200mm centre to centre. The 15 mm cross tee runner shall be suspended at 600mm centre to centre and further supported with 15 mm cross tee at 600mm centre to centre with interlocking arrangements to form grid of 600mm x 600mm. The main tee shall be supported by means of 4mm G.I. rod from slab/roof. The suspension shall be provided at 1200 to 1500mm centre to centre.

Providing and fixing high tensile strength acid and alkali resistant latex metal free composition nontoxic Fiber Glass Mesh (FGM) of minimum density of 145 GSM (Gram per SqM) and 5mm X 5mm meshing size for reinforcement of surfaces during all kinds of plaster works at the junction of masonry work and RCC work or on any other place as directed to receive plaster including fixing the FGM in 300mm wide patta with Cement mortar (1 part cement :1 part fine sand) stretched properly and at all the heights below and above highest plinth level including scaffolding etc complete as directed.

Providing & applying on new work three coats (first two coats are with brush and final coat is with roller) of Glossy or Matt/luster enamel paint of desired shade, of approved make, shade, brand and manufacture, on any surfaces, at all heights, to give an even shade, including thoroughly brushing the surface free from mortar droppings and other foreign matter and sand papering smooth. The paint shall be applied after applying a coat of primer of approved make and preparation of base surface using plaster of paris putty/white cement putty etc. with average minimum 1mm thickness etc. complete as directed .

Providing and laying pre-polished hand / machine cut green Kota stone of uniform shade of size 11”x 11” / 11”x17” / 17”x17” / 17”x23” /23”x23” or in required size as per drawing , 25 to 30 mm thick in flooring as per approved pattern over average 30 mm thick cement mortar 1:4 ( 1 part cement :4 part coarse sand) including spreading neat cement slurry @ 4.4 Kg / sq m with flush pointing of the joints with cement paste mixed with matching green colour, curing, machine / hand polishing ,cleaning with oxalic acid, wax polishing moping the finished surface of flooring with water and kerosene for 10 days etc. complete as directed. Note:-Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness.

Providing and laying pre-polished machine cut green Kota stone of uniform shade in required size as per drawing,18 to 20 mm thick in skirting / dado flush with plaster with a groove or projecting as per detail / approved pattern over a bedding of 12 mm thick cement mortar 1:4 ( 1 part cement :4 part coarse sand) including spreading neat cement slurry with flush pointing of the joints with cement paste mixed with matching green colour, curing, machine / hand polishing, wax polishing moping the finished surface with water and kerosene for 10 days etc. complete as directed. The joints of skirting / dado to be matched with flooring without any extra cost. Note:-Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness. The cost of making full "V" or half "V" grooves/bevelled edges of the kota stone is also included if required as per the drawing and as directed.

Providing and laying pre-polished machine cut single piece green Kota stone of uniform shade in required size as per drawing 25 to 40 mm thick for treads, risers, sides of staircase, kitchen platform, window cills over 20 mm thick cement mortar bed of CM 1:4 (1 part cement :4 part of coarse sand) with thick cement slurry including making 3 to 5 mm V shaped grooves if required, curing machine / hand, curing, grinding, polishing, wax polishing etc complete as directed. - For Kota stones of size above 1.0M and upto1.5 M long in single piece. Note:-Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness. The cost of making full "V" or half "V" grooves/bevelled edges of the kota stone is also included if required as per the drawing and as directed.

Providing and laying 50 mm thick IPS flooring with under layer of 38 mm thickness and top layer of 12 mm thickness complete as directed, 1:2:4 (1 part cement, 2 part coarse sand and 4 part stone aggregate 12.5 mm and down graded) finished smooth with top layer of 12 mm thick mortar in CM 1:2 (1 part cement : 2 part coarse sand )and cement slurry @ 2.2 Kg / Sq.M including rubbing/ grinding the top surface to match, including rounding off the junction and corners with floors and walls, necessary construction joints, finishing the top surface smooth / chequered or broom, curing etc. complete as directed. Note:-Aluminium strip/Groove filling shall be paid separately under respective item. Cutting of grooves shall be included under this item only.

Providing and laying 19 mm thick IPS in skirting / dado with under layer of 12mm and finishing top coat of 7 mm including cutting the wall and match the joint or projected with wall plaster, curing etc complete as directed. Note:-Aluminium strip/Groove filling shall be paid separately under respective item. Cutting of grooves shall be included under this item only.

Providing & mixing approved quality and make floor hardener of approved make as per manufacturers specification complete as directed.

Providing and laying in position First quality acid and alkali proof red Mandana stone of approved size and 25-30 mm thick for flooring including two coats of acid and alkali preventive primer, fixing stones on average 30 mm thick cement mortar bedding 1:4 (1 part cement mixed with acid and alkali proof powder, 4 part coarse sand) with acid proof powder keeping the joint 6 mm to 8 mm wide and 12mm deep all around, curing and filling the same with epoxy resin and hardener of approved quality including hand/machine polishing, wax polishing etc. complete as directed. Note:-Thickness of stone shall be 25 to 30mm.

Providing and laying Mandana stone skirting, dado, risers etc as per technical specification over 12 mm thick cement mortar CM 1:3 (1 part cement with acid and alkali proof powder: 3 parts coarse sand) bedding over two coats of acid and alkali proof primer including filling the joints with epoxy, polishing etc complete. Note:-Thickness of stone shall be 25 to 30mm Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness. The stone for single piece shall be up to 1500mm long for tread, risers, cills etc. The stone joints shall be filled-up with acid and alkali resistant epoxy based joint filler materials manufactured by M/s Laticrete/Ardex/equivalent approved make with approved quality pigment of permanent colour to match the shade of the slab ( keeping the joints 6mm wide and minimum 8mm deep all-around and filling the same with epoxy resin and hardener, cost of which is also included under this item only). The joints shall be filled in two/three or more runs in time intervals to achieve its surface flush with stone. Cost is inclusive of all.

Providing and laying 18 - 20 mm thick pre-polished to mirror finish machine cut approved quality Granite stone Flooring of required size (length and width of the stone slab), colour in approved pattern including bands, strips patta in flooring, platform top, treads / cills of uniform colour, texture and pattern over 20 mm thick cement mortar 1:4 ( 1 part cement : 4 part sand ) with cement paste @ 4.4 Kg/SqM filling of joints with white cement / cement mixed with colour pigments to match the shade, applying epoxy based damp proof coating on the base concrete surface, rounding off the exposed edges as per the drawing, necessary curing, polishing, protection of finished surface, cleaning the same finally etc. complete as directed. Note:-Basic rate of granite stone shall be Rs. 2200/Sqm The item also includes providing narrow bands up to 150mm width wherever required as per the drawing. If required, granite shall also be fixed by leaving 4mm x 4mm joints through spacers. The item also includes vanity counters etc. Granite stone shall be mirror polished, premoulded and prepolished and machine cut. Item rate shall also be inclusive of making V grooves as per drawing where ever required, full/half round moulding of the exposed edges as per the drawing, fixing grit aggregates back on stone with araldite/equivalent solution for bonding etc are included. Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness. Item also includes single piece granite shall be up to 1500 mm long for treads

Providing and laying 18 mm. to 20 mm thick pre-polished to mirror finish machine cut approved quality Granite stone of required size & shape (length and width of the stone slab), colour in approved pattern, single piece in skirting , dado , risers of uniform colour, texture and pattern over 12 mm thick cement mortar 1:3 ( 1 part cement : 3 part coarse sand ) with cement paste @ 4.4 Kg/SqM filling of joints with white cement / cement mixed with colour pigments to match the shade, applying epoxy based damp proof coating on the base concrete/wall surface, polishing the exposed edges as per the drawing, necessary curing, polishing, protection of finished surface, cleaning the same finally etc. complete as directed.The stone used should be in one single long piece up to 1500mm length as per the drawing. Only finished granite work shall be measured & considered for payment. Note:-Basic rate of granite stone shall be Rs. 2200/Sqm The item also includes providing and laying granite stone for risers of staircase, facia & drops, door frames, wall lining (veneer work), jambs, cills & soffits of window, door and ventilator openings. Item rate shall also be inclusive of making V groove as per drawing where ever required, full/half round moulding of the exposed edges as per the drawing, fixing grit aggregates back on stone with araldite/equivalent solution for bonding etc. Thickness of granite may vary from 18 mm to 20 mm. facias, drops etc shall be fixed using special resin based epoxy adhesives (araldite or equivalent approved). Granite stone shall be mirror polished, premoulded and prepolished and machine cut. Single piece granite shall be up to 1500 mm long whereas granite for door frame shall be of full length/Height. Cement slurry/paste shall be applied @ 4.4 Kg/SqM or more if required for required thickness. The item includes providing narrow bands also.

Labour charges for providing half round moulding on edges of kotah stone, green marble stone and granite stone by using all tools such as special grinding and art cutter machines including making the edges mirror polished etc complete as directed. Note:-This item is for edge moulding of stones other than granite. Edge moulding of granite stones for exposed edges are included under the respective items of granite themselves.

Labour charges for providing full round moulding on edges of kotah stone, green marble stone and granite stone by using all tools such as special grinding and art cutter machine including making the edges mirror polished etc complete as directed. Note:-This item is for edge moulding of stones other than granite. Edge moulding of granite stones for exposed edges are included under the respective items of granite themselves.

Labour charges for making antiskid strip in granite stone 25 mm width & 5 mm deep etc complete. Note:-This item is applicable for other stones as well.

Extra labour charges for providing opening of required size & shape for wash basins/ kitchen sink in kitchen platform, vanity counters and similar location in marble/stone work including necessary holes for pillar taps etc. including rubbing and polishing of cut edges etc. complete.

Providing & laying 500 micron gauge polythene sheet below grade slab, PCC, RCC slab etc. to the required level including supplying , loading and Unloading, storing transportation, laying, sealing of junctions and over laps up to 200mm, all leads and lifts and overlap included all complete

Providing and laying waterproofing treatment in sunken portion of WCs, bathroom etc. by applying cement slurry mixed with waterproofing cement compound of approved make consisting of applying: a) first layer of slurry of cement @0.488 kg/sqm mixed with water proofing cement compound@ 0.253 kg.sqm. This layer will be allowed to air cure for 4 hours. B) Second layer of slurry of cement @0.242 kg/sqm mixed with water proofing cement compound @0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate shall include preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. The work shall be carried out by a specialist agency in accordance with above specifications and shall carry a guarantee against leakage, seepage etc. for ten years.

Position suitable PVC water stops for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete & serrated with central bulb (225mm wide, 8-11 mm th.) etc. complete as directed

Providing 18 mm. to 20 mm thick pre-polished to mirror finish machine cut approved quality Granite stone facia & drops 150 mm wide to be fixed to the sub base by epoxy adhesive (araldite or equivalent), keeping in place till the joint is hard, cleaning etc. complete. Stone shall be in one single long piece up to 1500mm length as per the drawing. (Only finished granite work shall be measured & considered for payment).

Providing and laying minimum 20mm thick premium/ 1st quality Acid & Alkali proof stain resistant heavy duty industrial tile having MOH hardness minimum 7, flexural strength >38 N/Sq.mm, breaking strength as minimum 1700 N, density 2.4 gm/CC as minimum and having size 300 X 300 or as approved size, colour and shade having plain edges in flooring over average 37 mm thick cement mortar 1:4 (1 part cement: 4 part coarse sand) bed laid to requisite, line, level and slope, fixed with cement slurry of honey like consistency, 6 mm to 8 mm wide & 12mm joints all around, racking, and filling the same with acid and alkali proof epoxy resin and hardener of approved quality & colour, in line and level, curing, cleaning the area with water or water with mild acid etc complete as directed. Note:-Basic rate of shall be vitrified industrial floor tiles Rs. 1500/Sqm The cement mortar and cement paste shall be mixed with the liquid admixture as per recommendation of manufacture and the cost of admixture shall be paid separately. Tile: - Johnson's : Meteor series Restile : Beige, polo, steel grey, kota green. Or approved equivalent

Providing and laying cement water-proofing of average 115 mm thick for balcony, terrace etc at all the levels, with layer of 20 mm thick cement mortar 1:3 ( 1 part cement : 3 part coarse sand )mixed with water proofing compound of approved make and as specified by the manufacturer, laying brick bats of required size impregnating in to the base mortar bed with gap of 12 mm all around according to slope, level and curing the same, the gaps around brick bats filled with cement mortar 1:3 (1 part cement : 3 part coarse sand) mixed with waterproofing compound as above , 15 to 20 mm layer above brick bats, curing and testing of water proofing, laying China Mosaic flooring work over the prepared surface in slope using broken equal pieces of white glazed tiles not more than 25 to 37 mm wide and long and colored glazed tiles equal pieces for making pattas, vattas etc. as per details with necessary bedding in CM (1:4) laid in required slope, consolidating with wooden hammer, filling joints with Birla white cement, cleaning the surface and acid washing etc. complete as directed at any height. 1. The Work to be carried out at all the heights. The individual rates shall be inclusive of all lifts, lead and handling of materials, necessary scaffolding and staging, 2. Rates shall be inclusive of the slopes to be provided in all the above flooring items as directed and as per the drawings, garantee for 10 years. The work should be carried out through an approved specialised agency like India Water Proofing Co. or equivalent.

Providing & Fixing Acid and Alkali resistant Tiles Skirting Providing and laying minimum 10mm thick premium/1st quality stain resistant tiles having MOH hardness minimum 7, flexural strength minimum 35 N/Sq.mm, breaking strength as minimum 1700 N, density 2.2 gm/CC as minimum and having size as approved, colour and shade having plain edges in skirting over cement mortar 1:4 ( 1 part cement : 4 part coarse sand) to requisite, line, level and slope, fixed with cement slurry of honey like consistency, cleaning the joints with coir brush , filling the them with nosing angle, coving with white cement or white cement mixed with requisite matching colour pigment, curing, cleaning the area with water or water with mild acid etc complete as directed. Note:- Ready made coving tile skirting of Pelican or equivalent make as directed.

Extra for vacuum de-watering & finishing over concrete surface laid under relevent tender item of self finish cement concrete of grade M-20 / M-25/ M-30 or any surface immediate after surface vibration. It involves levelling of concrete in desire slop with Trimix surface Vibrator, Vacuum De-watering by Trimix Vacuum Pump and Suction Mat, finishing by Power Trowel with disk & blade up to desire finish, cuting groove as required by Groove Cutting Machine and curing etc. complete as manufacturers specification or as directed etc.

Providing and fixing in position interlocking rolling shutters of approved make of 18 gauge, 75 mm wide cold rolled, MS Lathe interlocked through entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with bracket including top cover, spring, axles, guide rails, tees, iron pulleys, bearings, handles, arrangements for inside and outside locking, holding-down bolts / MS lugs embedded in CC 1:2:4 including 2 or more coats of first quality synthetic enamel paint of approved make, over a coat of primer etc. complete as directed. (Measurements to be considered for payment shall be the clear size of opening plus guide channels on both sides for width and 450mm on top for drum height) - for providing and fixing in position interlocking mechanically operated rolling shutter with mechanical device chain and crank operated with pair of handles etc complete as directed.

Providing and fixing in position interlocking rolling shutters of approved make of 18 gauge, 75 mm wide cold rolled, MS Lathe interlocked through entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with bracket including top cover, spring, axles, guide rails, tees, iron pulleys, bearings, handles, arrangements for inside and outside locking, holding-down bolts / MS lugs embedded in CC 1:2:4 including 2 or more coats of first quality synthetic enamel paint of approved make, over a coat of primer etc. complete as directed. (Measurements to be considered for payment shall be the clear size of opening plus guide channels on both sides for width and 450mm on top for drum height). for providing and fixing in position interlocking rolling shutter partly grilled and mechanically operated with mechanical device chain and crank operated with pair of handles etc complete as directed

Providing, fabricating and fixing in position, grill, railing, steel ladder, Safety MS bars to windows/ ventilator of MS rolled sections as per architect’s details including cutting welding, grinding to smooth surface, fixing hold fast of MS sections embedded in concrete 1:2:4 (1 part cement, 2 part coarse sand, 4 part of stone aggregate 12 mm and down), anchor bolts including 2 or more coats of first quality synthetic enamel paint of approved make over a coat of primer etc. complete as directed.

Providing, fabricating and fixing in position MS inserts such as nosing, corner angles of columns, plates, flats, tee’s, protection channels of reception dock, supports, brackets and monorails, hooks, frame around cut-out, MS pipe sleeves etc. as per drawings and specifications, in true line and level including embedding the same into the permanent works at the time of casting of RCC works or fixing with or without base plate fixed to RCC element with appropriate size expansion bolts as per design, with necessary welding, grinding and painting with two or more coat of approved first quality synthetic enamel paint over a coat of primer etc. complete as directed.

Providing, fabricating and fixing in position M.S. gate made out of M.S. rolled/hollow (rounds/rectangular/ square etc.) sections as per architect’s details including shearing /cutting, riveting, welding, grinding to smooth surface of all works, pivots, hinges, MS solid shafts, MS fixing holdfasts to be grouted in concrete column / block, providing and fixing nuts bots fasteners as required, rail track if required, as per architect’s details, providing closing / locking arrangements, including painting with two or more coats of first quality synthetic enamel paint of approved quality and make over a coat of primer etc. complete as directed. (Individual member will be measured in RM / SqM and converted to weight by multiplying with co-efficient and shall be paid in Kgs. Nuts, bolts, washers required for fastening the hinges shall be deemed to have been included in the unit rates and nothing extra shall be paid for).

Providing, fabricating and fixing MS pipe railing as per the architect’s details / as directed using MS pipes / square or hollow section, with necessary specials including painting with two or more coats of synthetic enamel paint of approved make and quality over a coat of red oxide primer etc complete as directed. (MS standard rolled sections used in railing shall be measured and paid under respective item) Note:-MS Pipes shall be Class C (Heavy duty) for cold storages. For other places, the pipes shall be class B (Medium duty).

Providing, fabricating and fixing in position GI barbed wire fencing above ground with 2.4 M long Pre-cast pre-stressed cement concrete posts of 100mm X 100mm size casted using 20mm and downgraded stone grits and 4mm dia. 4 nos. pre-stressed wires, 500mm length post shall be grouted in PCC 1:2:4 (1 part cement: 2 parts coarse sand: 4 parts aggregates) block of size 450x450x600, 1900mm shall be the remaining length of the post above ground will be placed in true plumb and alignment at 2.00 M c/c, every 10th post and corner posts are to be strutted from both sides by two similar posts and the end post from one side using the same posts grouted in similar concrete blocks. This includes necessary excavation providing and fixing GI barbed wires of 12 to 14 gauge, 4 points wire with 12 horizontals and 4 diagonals fixing with approved U clips etc complete as directed.

Providing, fabricating and fixing 1050 mm total vertical length (around 825 mm clear height) in position GI barbed wire fencing over compound wall with 1350 mm long 50x50x6 mm angles with 300 mm angle post grouted with flared end in PCC 1:2:4 ( 1 part cement: 2 parts coarse sand: 4 parts aggregates) block of size up to 230x150x350 (H), 600 mm length of the angle straight and balance 450 mm will be bent and placed at 2.5 M c/c every 10th post or post at change in level, are to be strutted from both sides and the end post from one side using 1350 mm long MS angle 50x50x6 mm grouted in concrete block matching size. This includes necessary centring/ shuttering for the CC blocks 1:2:4 providing and fixing GI barbed wires of 12 to 14 gauge, 4 points wire with 7 horizontals and 4 diagonals fixing with approved U clips, painting the angles with two or more coats of approved first quality and make Aluminium/ synthetic enamel paint over a coat of primer etc all complete as per drawing / as directed.

Providing, fabricating and fixing in position grill of MS hollow section as per the details given by the architect including cutting, welding, grinding to smooth surface, fixing hold fast embedded in concrete 1:2:4, anchor bolts, painting with two or more coats of first quality synthetic enamel paint of approved make and quality over a coat of red-oxide primer complete as directed. (MS standard section used in grill shall be measured and paid under relevant Item)

Fabricating supplying and installing in position all types of railing to spiral stairs, other stairs, terrace and all other locations as called for with Stainless Steel of SS Grade-304 consisting of tubes of various sizes like 50mm,40mm,25mm,18mm dia etc., S.S. flats, S.S perforated sheet, S.S. plate, solid square and circular bars etc. arranged in verticals and horizontals with spacing as required and anchored to sides/tops of steps/slab as shown, hand rail and all other stainless steel pipes (wall thickness, minimum 1.25 mm), S.S.plate,S.S.Flat,S.S perforated sheet etc., fixed to stainless steel verticals through shaped custom fabricated SS flanges, S.S.caps and nuts, plates etc., as shown including approved brackets and fittings, anchoring arrangement such as fastener of approved or equivalent make, all fixing accessories, all cutting, bending, welding, grinding, drilling, tapping, weep hole and all other incidentals, and approved buffing to stainless steel members as directed by the Engineer-in-charge complete. The railing is 1000 mm to 1500 mm high (approx.) from top of finishing tread. The hand railing and other horizontal members shall be bend to the correct radius, profiles, shapes as per drawing, by the appropriate means without losing the profile of the pipe. Note:-Stainless Steel finish shall be of matt or glossy of specific grade or any other finish etc complete as directed.

Providing, fabricating & fixing in position window & ventilator grill, edge protection to columns, window & staircase trades etc., gratings, Guard rail, frames, bracket, ladder & similar work as called for with Stainless Steel of SS Grade-304 consisting of S.S. tubular section, S.S. flats, S.S. plate, square bars, angles etc. including all fixing accessories such as S.S. inserts etc., all cutting, bending, welding, grinding, drilling, tapping and all other incidentals, and approved buffing to stainless steel members as directed by the Engineer-in-charge complete . Note:- Stainless Steel finish shall be of matt or glossy of specific grade or any other finish etc complete as directed. The item also includes providing and fabricating drain grating, Gate, SS door, SS sliding door for storage/godown etc and frames as per profile, details and design as per the drawing and other similar works. The sections/members of stainless steel to be used under any other item of this contract and not included under the scope, shall be paid under this item only.

Providing , Fabricating and fixing in position M.S. gratings of M.S. Rolled section/ Flats including cutting, wastage, welding ( shop and site), grinding bolting wherever necessary painting with one coat of red oxide paint and two or more coats of approved make synthetic enamel paint to give an even shade, complete as directed.The payment for reinforcement as hold fast to be paid againsst the respective item .

Labour charges for fixing in position Mild Steel(MS) inserts, foundation bolts, templates, nosing angles and any other MS members supplied by equipment manufacturer for grouting in concrete including fixing and supporting firmly in position using welding with reinforcement bar/any other means till the concrete has gained the required strength cleaning the templates etc complete as directed.

Providing, fabricating and fixing in Trench lining/drain lining/drain pipes and such other locations cladding with stainless steel sheets/plates of grade-316 consisting of s.s flats, s.s.angles etc of grade-316 for its framework, including all necessary accessories such as s.s.inserts etc., all cutting, bending, welding, grinding, drilling, tapping and all other incidentals, and approved buffing to stainless steel members as directed by the Engineer-in-charge or as per the drawing

Supplying, fabricating, assembling, hoisting and fixing in position to alignments & levels as per approved drawings, structural steel work in-built up roof truss girders and side claddings with booms, lattice girders roof trusses, gable frame, purlins / built-up purlins, cladding structures, side runners, etc., to detail welded (welding as specified by the structural consultant) / bolted constructions comprising R.S. joints, channels, angles, plates or any MS rolled section including necessary permanent rivets, bolts & nuts, welding, handling straightening, cutting, making holes by drill machine, shop / site assembly, erection, ( including preparation of template) transport to site, storing, etc., surface preparation by rubbing with motorised wired brush, sand paper, emery machines and painting with shop/site coat of red oxide primer prior to erection and two or more coats of first quality synthetic enamel paint of approved make and quality over a coat of red oxide primer after erecting in position at all heights including necessary scaffolding and staging, as required complete as directed. Payment will be made on the basis of standard section weights for net weight erected in position excluding rivets, temporary bolts, etc., but payment will be made for permanent bolts, nuts and washers.

Supplying, fabricating, assembling, hoisting and fixing in position to alignments & levels as per approved drawings, structural steel work in-built up roof truss girders and side claddings with booms, lattice girders roof trusses, gable frame, purlins / built-up purlins, cladding structures, side runners, etc., to detail welded (welding as specified by the structural consultant) / bolted MS rolled section B class pipes / medium duty tubular square / rectangular sections having minimum yield strength of 310 N/Sq.mm and confirming to the specifications as per IS 4923 & IS 1161 of approved make including cutting , radius bending, mitring and Welding after matching including necessary permanent rivets, bolts & nuts, welding, handling straightening, cutting, making holes by drill machine, shop / site assembly, erection, ( including preparation of template) transport to site, storing, etc., surface preparation by rubbing with motorised wired brush, sand paper, emery machines and painting with shop/site coat of red oxide primer prior to erection and two or more coats of first quality synthetic enamel paint of approved make and quality over a coat of red oxide primer after erecting in position at all heights including necessary scaffolding and staging, as required complete as directed. (MS rolled sections like flats, plates, angles, T’s, ‘ I ‘/ ’C’ sections etc used shall be measured and paid under relevant item)

Providing, cutting / bending to shape & size, fixing in position MS chequered plate for covers of trenches, steps, landings, platforms etc. as per drawings / details including bending the edges, grinding them smooth with rounding the sharp edges / corners, painting with one coat of red oxide primer and two or more coats of first quality synthetic enamel paint of approved make and quality over primer coat etc. complete as specified and as directed.

Providing & fixing holding down bolts with nut, washer, upper portion of the bolts up to 100 mm portion or as specified threaded to requirement etc. complete as directed. (Rate to include for placing the bolts in position with templates etc.)

Supplying and fixing UV resistant transparent polycarbonate sheet 2 mm thick of approved make, size, and tint in plain or curved profile for roof sheeting with anodised aluminium beading fixed with GI bolts or EPDM coated self tapping screws with EPDM sealing washer, filling the gaps with silicon sealant. Item rates shall be include cost of plastic caps of approved colour of UV resistance, sealant wherever required etc complete as per architects drawing and as directed.

Providing and fixing in Roof sheet/ R.C.C. slab Wind operated approved or equivalent make 600 mm dia Turbo – ventilators/ roof extractors with sky light, made from rotating heads having turbine blades of higrade aluminium, top and neck of stainless steel 304 grade, steel bearing with dust proof bearing housing or GFP Pushing instead of bearing, UV stabilised non-coloured translucent 3mm thick FRP moulded one piece construction (monolithic) venturi dome and corrugated base sheet (similar FRP sheets 3 mm thick UV resistant) of appropriate size having the profile matching with existing roof sheet with double action natural ventilation system powered by natural flow of air, boosts / extracts the hot and contaminated air / gases, obnoxious fumes, bad odour outside for healthy and improved environment inside Godowns including cutting the roof if necessary, fixing the leakage in roof etc complete as directed. Turbo ventilator as per drawing with the roof sheets including all fittings and fasteners as per manufacturer’s specification, making the joints water proof to prevent entry of rain water

Providing and fixing flashings, cappings, barge pieces, gutter pieces, trims and other specials as per drawing formed out of coated steel in same material, substrate and coating as external/internal sheeting, and fixed by means of hex-head self drilling stitching screws in girth upto 500 mm

Providing & fixing GALVALUME colour coated cold rolled sheets made out of 0.45mm base metal thickness and Total Coated Thickness as 0.50mm, yield and tensile strength minimum 550 Mpa cold rolled sheet with hot dip metallic coating of aluminium zinc alloy 150 Gms/SqM, density minimum 4.45 Kg/SqM with minimum 20 microns super durable polyester paint or silicon modified polyester on top and 5 microns back-up epoxy coating at the bottom having 975/1015mm cover width with 28.5 mm high crest at 195/200mm C/C in length as approved by the architect and with necessary suitable imported galvanised carbon steel 40micron zinc coated/minimum 20micron Zinc-Tin alloy coated Hexagonal head, self drilling & self tapping screws of ITW Buildiex(R) AS 3566 Class 3/ HILTI/BOSCH having drilling capacity minimum 6-8mm and in required diameter and length fixed using torque drill machine all complete with EPDM sealing washers with sealant. Rate should include cost of plastic caps of approved colour of UV resistance and button bolts etc. for the fasteners. Rate to include also fixing in roofing and cladding, all accessories and utilities like ridge, corner piece, aprons, barge boards, gutters, flashings, end pieces, etc., all complete. The rates shall include all materials, tool / tackles, labour, scaffolding including handling and storage of the materials, providing guarantee against perforation for 10 years etc complete as directed for all heights. Measurement shall be paid for the plain area of the sheet laid. Overlaps, wastages,corrugation etc are inclusive with the rates and shall not be paid for. Note:-Basic rate of sheet shall be Rs.500/ Sqm. Item also incudes Flushing, Ridge, Eve-curve etc and shall be paid in SqM.

Providing and fixing suspended 12.5mm Plain Gypsum Board ceiling which includes GI Perimeter Channel fixed along the perimeter of existing wall/ partition with the help of screws at 600mm centres. GI Ceiling Angle shall be suspended at up to suitable height as per site conditions by fixing it to the GI soffit clit with Soffit Cleat and Raw Plug creating 1220mm x 1220mm grid. GI Intermediate channel shall be fixed to the GI Ceiling Angle with 2 Nos of 4.2x13mm GI metal to metal screws. The GI Ceiling Section shall be then fixed to the GI Intermediate Channel with the help of Connecting Clip and in direction perpendicular to the Intermediate channel at 457mm c/c. All framing and grid section shall be GI (as per IS 513) having yield strength 300 mpa and galvanized finish of 150 GSM as per IS 277. Single layer of 12.5mm tapered edge Plain Gypsum Board (Confirming to IS 2095-Part-I, 2011) shall be then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Finally square and tapered edges of the boards shall be joined and finished so as to have a flush look which includes filling and finishing with Jointing Compound & Joint Paper tape. The contractor should prepare shop drawings based on the concept drawing and get it approved by the Engineer-in-charge. After approval of drawings, the contractor shall prepare the sample based on the drawing and get it approved by the Engineer-in-Charge before execution. Rates shall be inclusive of cost of making cut outs/ openings for electrical fixtures, tube lights/ air-conditioners, grills, diffusers etc & providing additional sections for strengthening the openings/ cut-outs, making grooves between wall & board or as per drawing for all floor, all level, all height etc as directed by Engineer in charge. Area of cut-outs shall not be deducted and no extra payment shall be considered for additional sections provided. Only plan area shall be considered for recording of measurements.

Providing and fixing night latch of approved make with a set of keys etc complete as directed.

Dismantling stone/Brick masonry walls or partition wall plastered or un plastered as per instructions including finishing the broken surface to match with the surroundings, removal and disposal of debries within site including cutting the reinforcement bars, if any etc. complete as directed. Note:-Item includes disposal of debris anywhere out side site.

Dismantling the RCC beams, slabs, lintels, columns, pardi, walls, platform etc. including finishing the broken surface to match with the surroundings, removal and disposal of debries within site, including cutting the reinforcement/ MS inserts stacking the same and handing over to stores / yard within site etc. complete as directed. Note:-Item includes disposal of debris anywhere out side site.

Providing and filling the jharies 25mm to 150mm wide and 50mm to 100mm deep with PCC 1:2:4 (1 part cement:2part sand: 4 parts 12.5 and down graded aggregates) and finishing the same as per surroundings including scaffolding, cutting the reinforcement bars, curing etc. complete as directed

Making holes up to 30 cms in dia or 30 x 30 cms in size in RCC works and filling the same with PCC (1:2:4) and finishing the same as per surrounding including scaffolding, cutting the reinforcement bars, curing etc. complete as directed.

Providing and fixing in RCC side wall or bottom or cover slab of sump or water tank 75 mm diameter GI B class pipe insert of up to 600 mm long with puddle flange and with outside flange / threaded ( on one end) for connecting the pipeline for inlet, outlet, drain / overflow etc complete as directed.

Providing and fixing in RCC side wall or bottom or cover slab of sump or water tank 50 mm diameter GI B class pipe insert of up to 600 mm long with puddle flange and with outside flange / threaded ( on one end) for connecting the pipeline for inlet, outlet, drain / overflow etc complete as directed.

Providing and fixing removable CI grating of approved quality for rain water pipes inlet including painting the same with approved paint etc complete as directed for 100 mm diameter rain water pipe etc complete as directed.

Providing and fixing removable CI grating of approved quality for rain water pipes inlet including painting the same with approved paint etc complete as directed for 150 mm diameter rain water pipe etc complete as directed.

Dismantling kota stone/ mandana stone/ mosaic tiles in floor/dado /skirting etc. with mortar bedding as per instructions including finishing the broken surface to match with the surroundings. Disposing debris/ muck as directed within the site etc. complete as directed. Note:-Item includes disposal of debris anywhere out side site. Item also includes Vitrified, ceramic, glazed tiles, all types of natural stone floorings etc complete.

Dismantling plain cement concrete in flooring/pavement/ wall foundation etc. as per instruction and disposing the debris/muck within the site at approved location. Note:-Item includes disposal of debris anywhere out side site.

Removing existing doors/windows/ventilators/ grills, Rolling shutter etc. carefully by removing the screws / bolts / hold fasts as directed and stacking & storing the same at site and handing over to stores / yard and finishing the broken surface to match with surroundings, disposal of debris within site etc. complete as directed. Note:-The existing doors/windows/ventilators/grills, rolling shutters removed if any, shall be hand over to PA.

Dismantling / scrapping and removing existing plain/sand faced/grit cement plaster of any thickness from the brick/RCC works including necessary scaffolding at all heights and levels and disposing the debries within the site etc. complete as directed. Note:-Item includes disposal of debris anywhere out side site.

Providing and Fixing heavy duty PVC rungs of around 350 mm long and around 180 mm wide complete as directed.

Providing and fixing air vent cowl of PVC as per approved sample for 150/100/75 diameter pipe including jointing using adhesive as recommended by manufacturer appropriately etc complete as directed.

Dismantling steel work in built up sections in angles, tees, flats, pipes, chain link, barbed wire, baseplate and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. at all heights including dismembering and stacking within the premises upto a lead of 350m. and scaffolding complete as directed.

Charges for making holes in brick walls with or without plaster / tiles with mechanical cutter like HILTI etc. including disposing the debris and finishing the same as per requirements. Measurement of holes will be taken per no. of holes drilled as per following range of diameters. Making of holes by hammer and chisel will not be considered in this item. For Diameter of holes upto 201 mm to 300 mm clear.

Providing and Laying Plinth Protection with PCC 1:3:6 (1 part cement: 3 part sand: 6 parts 12.5 and down graded aggregates) (self finish) 50 mm thick in panels of size 600mmx600mm laid over fly ash brick edge soling, laid over compacted sand bed of 100 mm thick over well compacted earth etc. complete as directed

Providing and making Core Cutting in R.C.C elements of any thickness up to 450mm deep bore using core cutter machines and tools etc complete as directed. For 100mm dia.

Providing and making Core Cutting in R.C.C elements of any thickness up to 450mm deep bore using core cutter machines and tools etc complete as directed. For 150mm dia.

Providing & fixing of uPVC pipe of approved ISI mark of required diameter and length for Weep hole, including leveling, placing in the RCC or masonry, secure the pipe during fixing and concreting. etc. complete as directed for 50mm to 75mm dia. Suitable filter media to be provided on back side of weep hole as per drawing and directed.

Supplying, Erection, Testing and commissioning of approved make Automatic Sliding Gate Motor with all necessary arrangement. The motor should be of suitable rating as instructed by Engineer incharge.

Supplying, Erection, Testing and commissioning of approved make sliding gate opener motor control unit PCB controller circuit board electronic card with remote control kit. The controller should be suitable for driving the sliding gate motor and the panel should be as per the drawing approved by Engineer incharge

Supply and fixing of High strength Aluminium Packer Nozzle at required locations and fixing in position using high strength polymer modified mortar as per manufacturer's recomendations so as to facilitate injection grouting using Electrically operated pressure injecting pump to stop the water seepage as per manufacture specifications.

Pressure grouting with cementitious non-shrinking pressure injection grout material of approved make including chemicals, cement, packers, connectors, labours, tools and tackles etc., complete as per Manufacturer’s application methodology & as directed by engineer in charge. Payment will be made based on actual consumption of only cementitious non-shrinking grouting material utilised in the works.

Surface dressing including preparation of sub grade of road bringing earth work to required grade, slope and camber in the existing surface, including cutting or filling earth up to 300 mm thickness, watering, consolidation with 8-10 MT Power Road Roller, etc. complete as per details and as directed

Providing & laying base course in two layers in compacted thickness of 100 mm (each course 100 mm thick consolidated), using stone aggregates of nominal size 65 mm, including filling voids with similar stone of smaller size, similar stone grit, stone aggregates of suitable size, dry rolling, spreading the binding material like murrum, watering and consolidation with 8-10 MT power road roller etc. complete as directed.

Providing and laying pre-cast / cast in- situ kerbing in cement concrete M-20 and 450mm wide, 75 to 100 mm thick and total 250 high, 100-125 mm thick web, edge duly chamfered including necessary excavation, surface dressing, cutting the road, laying PCC 1:5:10 (1 part cement 5 part coarse sand 10 part stone aggregate 20/37 mm and down) 100 mm thick, shuttering / moulds for exposed finish or provide smooth plaster with neat cement finish, curing as per approved drawing etc complete as directed. Note:-Pre-cast kerb stones may be of sizes other than stipulated above as per the architectural drawings etc complete as directed. The grade of concrete shall be M25 instead of M20.

Providing and laying cement concrete of grade M-25 in pavements, roads and kerbs over prepared sub-base in alternate panels of width up to 3.5 and length up to 6.0 M or as per architects’ drawing in the line level maintaining slope including form work using MS channels of required height, compacting with needle vibrator and surface vibrator, floating the surface smooth, providing stripped/broom finish evenly, providing and cutting necessary grooves of 6mm wide X 10mm deep and construction/expansion joints of 25mm wide and depth as per drawing with heavy duty cutter machine, finishing the same and casting kerbs as per drawing, providing necessary steel reinforcement, curing etc. complete as per the drawing/as directed. (Item includes kerb casting. Reinforcement steel, filling of expansion joint with filler material shall be measured separately in relevant tender items and paid for)

Providing and filling of SHALITEX sealing compound of grade A –IS 1834-1984 in the contraction/ expansion joints of the RCC roads/hard park .The joints shall be of size 25mm wide X 25 mm deep. Before applying the sealing compound the sides of the joints should be cleaned of dust and shalitex primer should be applied .The rate includes labour charges for laying along with heating the compound etc., as per the manufacturer’s specification and as directed.

Providing and fixing 1.8 M height chain link fencing as per drawing / details : a) Providing and fixing 49.5mm x 49.5mm x3.66mm ( Weight/RM - 4.93 kg) MS medium class box section, 2.5 meter long with 150 x 150 x 6 mm thick base plate with necessary clits of 50 x 6 MS flat on the pole, at 2.5 M c/c, 500 mm grouted in toe wall or ground in CC 1:2:4 block of size 45 x 45 x 50 cms., including necessary excavation, c/s. ( The toe wall will be measured under relevant item of works ), b) To form rectangular panel frame out of ISA 50 x 50 x 6, 1.8 M vertically apart and between two vertical hallow box support, welded with matching MS angle / flat clits so as to form the rectangular panels with necessary welding, nuts and bolts and washers, c) Chain link of 50 x 50mm size -10 gauge, covering the panels of MS angles, fixed with 32 x 6 mm MS flat as beading with making necessary holes and fixing with 10 mm dia 40 mm bolts with washers, nuts etc. complete. d) Painting the vertical posts, Note:-Painting the vertical posts, chain link fencing, framing etc with two or more coats of approved make aluminium paint over a coat of primer of approved make

Providing and laying precast cement concrete interlocking pavement blocks thick 80MM of approved quality (PU / Rubber mould finish) and make having compressive strength of minimum 350 Kg/ sqcm thicknesswith smooth or approved finish and edges duly chamfered in required color and pattern over compacted 50mm thick natural river sand bed to the required line , level and compacted the blocks laid by plate vibrator and filling the joints with fine sand etc complete as directed.

Providing and laying in a compact manner 230mm thick compacted thickness rubble soling in road / hard park in two layers using average 65 to 100mm size stones, including filling in the voids with largest possible stone spallings and murrum, consolidating each layer with 80-100 KN vibratory road roller, etc complete as directed.

Providing & applying Thermoplastic paint of approved or equivalent make and desire shade on bituminous / concrete surface, including scrubbing of road / kerb surface by wire brush to dislocate the dust from the surface, plotting of points on the carriageway for centerline & edge line marking, pre-marking on Centerlines/Edge line /Kerbline using string & chalk, including Hand propelled machine, the thermoplastic material is to be pre-heated while all the above activities are carried out, The molten thermoplastic material is transferred then from the pre-heater to applicator machine. all complete as manufacturer's specification and as directed.

Providing and fixing mild steel dowel/ tie bars of approved make including greasing etc. in concrete pavement as per details complete and as directed.

Providing & laying 40mm dia UPVC pipe of approved make and pressure 6 kg./sq.cm. in sheathing for dowel / tie bars in concrete pavements as per details including plugging the ends using uPVC pipe caps and adhesives etc. complete as directed.

Providing & fixing heavy duty Gun Metal wheel valve of approved quality and make ISI marked, for lines of following diameters complete as directed - For 80 mm dia NB pipeline.

Providing & fixing heavy duty Gun Metal wheel valve of approved quality and make ISI marked, for lines of following diameters complete as directed - For 50 mm dia NB pipeline.

Providing & fixing heavy duty Gun Metal wheel valve of approved quality and make ISI marked, for lines of following diameters complete as directed - For 40 mm dia NB pipeline.

Providing & fixing heavy duty Gun Metal wheel valve of approved quality and make ISI marked, for lines of following diameters complete as directed - For 25 mm dia NB pipeline.

Providing and fixing chromium plated brass bib cock of approved make with chromium plated flange (disc) etc. for 15 mm dia NB pipeline, complete as directed.

Providing and fixing longbody CP brass bib cock of approved make with chromium plated flange (disc) etc. for 15 mm dia NB pipeline, complete as directed.

Providing and fixing chromium plated concealed brass heavy-duty stop cock of approved make with chromium plated flange (disc) etc. complete as directed - For 15 mm dia NB pipeline.

Providing and fixing chromium plated brass heavy duty angle valve of approved make with chromium plated flange (disc) etc. complete as directed - For 15 mm dia NB pipeline.

Providing & fixing brass chromium plated towel rail of approved make of 610 mm length including drilling, supply and fixing brass screws securing the rail firmly at both the ends etc. complete as directed.

Providing & fixing CI Circular manhole cover of 750mm dia. of 40 Kg. weight including CI frame of approved make. The cover shall be got approved in advance and shall be fixed by grouting the frame in brickwork / RCC cover slab, including painting with two coats of bituminous paint etc. complete as directed.

Providing & fixing 25 mm dia NB brass heavy duty Ball Cock of approved make including fixing the same etc. complete as directed.

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 10kg/cm2 etc. complete as directed. For 25mm Dia.

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 10kg/cm2 etc. complete as directed. For 32mm Dia.

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 10kg/cm2 etc. complete as directed. For 40mm Dia.

Providing and fixing forged brass lever operated ball valve of full flow with forged brass ball (Machined to mirror smooth finish with hard chrome plated) and spindle with setting and gland of superior quality having minimum working pressure of 10kg/cm2 etc. complete as directed. For 50mm Dia.

Providing and Fixing, testing & commissioning of C.P. brass exposed type flush valve for Urinal Pressmatic of approved or equivalent make with regulator, 25 mm dia C.P. flush pipe with clamp and adapter, rubber joint, C.P. brass wall flange, elbow complete with all other accessories Including connection to urinal & cutting and making good the walls wherever required. All work complete as per specification or as directed.

Providing & Fixing HDPE pipe 110mm 4 kg pressure 4984 PE 80 with welding, all fitting such as bend, tee, reducer etc complete. Note:Item shall be executed considering IS14333 and with electrofusion welding with couplers and fittings.

Providing & Laying HDPE pipe line of approved make as per specification & as directed (material grade PE-80 & PN 4 pressure rating) as per IS 14333 (1996) with welding all fitting such as bend, tee, reducer etc complete - 160 mm dia. Note:Item shall be executed considering IS14333 and with electrofusion welding with couplers and fittings.

Providing & Fixing HDPE pipe 200mm 4 kg pressure 4984 PE 80 with welding, all fitting such as bend, tee, reducer etc complete. Note: Item shall be executed considering IS14333 and with electrofusion welding with couplers and fittings.

Providing & Laying HDPE pipe line of approved make as per specification & as directed (material grade PE-80 & PN 4 pressure rating) as per IS 14333 (1996) with welding all fitting such as bend, tee, reducer etc complete - 250 mm dia. Note: Item shall be executed considering IS14333 and with electrofusion welding with couplers and fittings.

Providing & Laying HDPE pipe line of approved make as per specification & as directed (material grade PE-80 & PN 4 pressure rating) as per IS 14333 (1996) with welding all fitting such as bend, tee, reducer etc complete - 315 mm dia. Note: Item shall be executed considering IS14333 and with electrofusion welding with couplers and fittings.

Providing and fixing in position tested 25mm nominal bore concealed underground waterline UPVC pipes confirming to ASTM D.1785 for pipes and schedule 80 including solvent jointing of applying primer of P70 and solvent of UPVC 705 with all fittings like bends, tees, reducers, elbows, unions, etc. confirming to ASTM D.2467 Schedule 80 including all necessary excavation, providing and applying metal primer and two coats of Bituminous paint of approved make after successful pressure testing of the pipeline, sand cushioning and covering with sand, refilling of trenches, compaction etc. complete as directed.

Providing and fixing in position tested 32mm nominal bore concealed underground waterline UPVC pipes confirming to ASTM D.1785 for pipes and schedule 80 including solvent jointing of applying primer of P70 and solvent of UPVC 705 with all fittings like bends, tees, reducers, elbows, unions, etc. confirming to ASTM D.2467 Schedule 80 including all necessary excavation, providing and applying metal primer and two coats of Bituminous paint of approved make after successful pressure testing of the pipeline, sand cushioning and covering with sand, refilling of trenches, compaction etc. complete as directed.

Providing and fixing in position tested 50mm nominal bore concealed underground waterline UPVC pipes confirming to ASTM D.1785 for pipes and schedule 80 including solvent jointing of applying primer of P70 and solvent of UPVC 705 with all fittings like bends, tees, reducers, elbows, unions, etc. confirming to ASTM D.2467 Schedule 80 including all necessary excavation, providing and applying metal primer and two coats of Bituminous paint of approved make after successful pressure testing of the pipeline, sand cushioning and covering with sand, refilling of trenches, compaction etc. complete as directed.

Providing and fixing in position tested 100mm nominal bore concealed underground waterline UPVC pipes confirming to ASTM D.1785 for pipes and schedule 80 including solvent jointing of applying primer of P70 and solvent of UPVC 705 with all fittings like bends, tees, reducers, elbows, unions, etc. confirming to ASTM D.2467 Schedule 80 including all necessary excavation, providing and applying metal primer and two coats of Bituminous paint of approved make after successful pressure testing of the pipeline, sand cushioning and covering with sand, refilling of trenches, compaction etc. complete as directed.

Providing and fixing concealed/ open 50 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes for water line 10Kg/ cm2, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as directed Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing and fixing concealed/ open 40 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes for water line 10Kg/ cm2, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as directed Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing and fixing concealed/ open 32 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes for water line 10Kg/ cm2, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as directed Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing and fixing concealed/ open 25 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes for water line 10Kg/ cm2, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as directed Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing and fixing concealed/ open 20 mm dia Chlorinated Polyvinyl Chloride (CPVC) pipes for water line 10Kg/ cm2, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as directed Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing, Laying & fixing Open /Concealed 110mm dia unplastized Polyvinyl Chloride (uPVC) pipes for water line 10KG/cm2, having thermal stability for hot & cold water supply, including all uPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as directed

Providing, Laying & fixing Open /Concealed 75mm dia unplastized Polyvinyl Chloride (uPVC) pipes for water line 10KG/cm2, having thermal stability for hot & cold water supply, including all uPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step uPVC solvent cement and testing of joints complete as directed

Providing and fixing concealed/ open Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge - 15 mm dia water line 10Kg/ cm2. Note: The class of cPVC pipe shall be considered as SDR-11 instead of cPVC pipes for water lines rated at 10 Kg/cm².

Providing and Fixing 110x110 mm uPVC 'P' trap with 2-3 inlets required size fItting with seal 50 mm of self cleansing design floor/urinal trap without vent suspended with supporting clamp or in sunken portion including cutting and making good the walls and floors wherever required complete in all respects.

Providing, fixing, testing & commissioning of C.I. Butterfly valve conforming to IS : 13095 with flanges, gaskets, nuts, bolts and washers complete for following sizes :- [PN 25 rating]. but for 65 mm dia

Providing & fixing and testing, heavy quality Non Return Valve (NRV) with all necessary fittings like union, couplings, tees, etc. complete. on GI/cPVC/uPVC lines of the following nominal bore (NB) size as directed for 25mm dia

Providing & fixing and testing, heavy quality Non Return Valve (NRV) with all necessary fittings like union, couplings, tees, etc. complete. on GI/cPVC/uPVC lines of the following nominal bore (NB) size as directed for 32mm dia

Providing and fixing CP brass garden bib cock complete as directed for 15 mm dia NB pipeline.

Providing & fixing brass chromium plated Toilet paper holder with flap including drilling, supply and fixing brass screws etc. complete as directed.

Providing & fixing open uPVC pipe SCH-80 class water pipe line of ISI mark of following diameters at all levels, including all necessary heavy duty specials (fittings) of ISI mark, fixing with approved arrangement viz. standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , making holes, cutting floors, making good the walls and floors etc. complete as directed for 25mm dia .

Providing & fixing open uPVC pipe SCH-80 class water pipe line of ISI mark of following diameters at all levels, including all necessary heavy duty specials (fittings) of ISI mark, fixing with approved arrangement viz. standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , making holes, cutting floors, making good the walls and floors etc. complete as directed for 32mm dia .

Providing & fixing open uPVC pipe SCH-80 class water pipe line of ISI mark of following diameters at all levels, including all necessary heavy duty specials (fittings) of ISI mark, fixing with approved arrangement viz. standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , making holes, cutting floors, making good the walls and floors etc. complete as directed for 40mm dia .

Providing & fixing open uPVC pipe SCH-80 class water pipe line of ISI mark of following diameters at all levels, including all necessary heavy duty specials (fittings) of ISI mark, fixing with approved arrangement viz. standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , making holes, cutting floors, making good the walls and floors etc. complete as directed for 50mm dia .

Providing, fixing and testing heavy duty lever operated wafer type Butter fly valve (confirming to IS 13095) manufactured from Ductile Cast Iron/SG Iron, lever & locking plate made from carbon steel, various other components made from carbon steel and stainless steel metals including providing and fixing with compatible insert counter flanges with bolts and nuts as per manufacturers recommendations to be fixed with GI/uPVC/cPVC pipelines of the following nominal bore (NB) size etc complete as directed of approved make for providing, fixing and testing of 50mm dia Butter fly Valve.

Providing and fixing Stainless Steel grade 304 perforated trap cover of 100 X 100mm (minimum 18SWG) into floor tile including cutting of tile, silicon filling for water proofing, etc. complete for the balcony drain etc complete as directed

Providing & fixing open uPVC SCH-80 class water pipeline of ISI mark and approved make of following diameters at all levels, including all necessary heavy duty specials and fittings of ISI mark and of approved make, fixing with arrangement viz. standard pattern holders bat clamps made out of Galvanised Steel (GI) flat carrier fixed with GI bolts in the RCC or brick masonry and GI “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed, making holes, cutting floors, making good the walls and floors etc. complete as directed - for providing and laying 65mm dia uPVC pipeline.

Providing & fixing open uPVC SCH-80 class water pipeline of ISI mark and approved make of following diameters at all levels, including all necessary heavy duty specials and fittings of ISI mark and of approved make, fixing with arrangement viz. standard pattern holders bat clamps made out of Galvanised Steel (GI) flat carrier fixed with GI bolts in the RCC or brick masonry and GI “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed, making holes, cutting floors, making good the walls and floors etc. complete as directed - for providing and laying 80mm dia uPVC pipeline.

Providing and laying concealed in earth waterline uPVC pipe SCH- 80 class water pipe line of ISI mark and approved make of the following diameter including all necessary heavy duty specials and fittings of ISI mark and of approved make, including excavation of trenches in soil/murum/rock up to 900mm depth, laying and jointing the pipe in line and level, filling coarse sand for 200mm dia. annular space all around pipe and as per manufacturer's specification, refilling earth, compacting & watering etc complete as directed - for providing and laying 65mm dia uPVC pipeline.

Providing and installing on terrace, multilayered cylindrical vertical PVC water storage tanks of approved make of capacity from 500 ltrs to 5000 ltrs with closed top having manhole and cover with threaded lid & extra insert lid for protection against algae formation, UV stabilised with white coloured outer layer, water tank shall be made from food grade material including shifting the tank from site store, supplying and fixing connection inlets, outlets, air vents, overflow, drain pipes including washers, check nuts, Neosprine gaskets etc of specified sizes and as per the recommendations of manufacturer including hydraulic testing and painting all the accessories with one coat of primer and two coats of synthetic enamel paint of approved make if required etc complete as directed. Note: Item also includes providing & fixing of brass float valve with Flexible Rod and Nitrile Rubber Seal & Plastic Ball.

Providing and laying concealed underground waterline of “B” class GI pipe of ISI mark of the following diameters, including all necessary heavy duty specials of ISI mark, including excavation in soil/murum/rock, providing and applying metal primer and two coats of Bituminous paint of approved make after successful pressure testing of the pipeline, sand cushioning and covering with sand, refilling of trenches, compaction etc. complete as directed -for 65 mm nominal bore (NB) GI pipe.

Providing & Fixing Air release valve (confirming to IS 6912, IS 5192-1 & IS 319) manufactured from Brass Metal, Stainless steel spring and other components made from polypropylene and nitrile rubber etc as per manufacturers specs to be fixed with GI/uPVC/cPVC pipelines of the following nominal bore (NB) size etc complete as directed of approved make for providing, fixing and testing of 100 mm dia Air release Valve

Providing and laying 300 mm diameter non-pressure class NP2 RCC Hume pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Providing and laying 75 mm diameter uPVC rain water line of 4 Kg / Sq cm rating of approved make with all necessary specials to be jointed adhesive as per manufacturers specifications etc complete for open pipeline / in brick wall / RCC structure including clamping to secure in position etc. complete as directed.

Providing and laying 110 mm diameter uPVC rain water line of 4 Kg / Sq cm rating of approved make with all necessary specials to be jointed adhesive as per manufacturers specifications etc complete for open pipeline / in brick wall / RCC structure including clamping to secure in position etc. complete as directed.

Providing and laying 160 mm diameter uPVC rain water line of 4 Kg / Sq cm rating of approved make with all necessary specials to be jointed adhesive as per manufacturers specifications etc complete for open pipeline / in brick wall / RCC structure including clamping to secure in position etc. complete as directed.

Providing and fixing first quality white glazed wash basin of 550 mm x 400 mm size, approved shape as per details of approved make and quality with necessary specials, one chromium plated brass pillar cock of 15 mm size, one 15 mm CP angle valve size, one 15 mm CP angle valve chromium plated, connecting CP pipes with nuts and all fittings, 31 mm dia. CP waste coupling and rubber plug with CP chain, heavy brackets with two coats of aluminium paint over brackets, and 32 mm dia GI concealed waste pipe in wall with bend etc. complete as directed.

Providing and fixing 1mm thick stainless steel sink of approved make of size 600 x 450 x 200 or 250 mm with drain board on one side including all necessary fittings and specials such as CI brackets, overflow, rubber plugs, CP brass chain, 63 mm dia. CP brass waste coupling, 40 mm dia. CP waste pipe, applying two coats of aluminium paint to the brackets etc. complete as directed.

Providing and fixing automatic/ manually operated low level white glazed vitreous china flushing cistern of approved make with suitable CP brass flushing bend conforming with IS:2556 and as specified / directed.

Providing and fixing 32 mm dia chromium plated brass heavy type approved quality bottle trap with matching wall flange etc. all complete as directed.

Providing and laying 450 mm diameter non-pressure class NP2 RCC Hume pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Providing and laying 600 mm diameter non-pressure class NP2 RCC Hume pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Providing and fixing looking mirror 5 mm thick of approved make over a backing of 12 mm thick Novaboard firmly fixed with brass oxidized screws , CP cup type screw etc. including the painting the exposed surfaces complete as directed.

Providing and fixing liquid soap holder with soap bottle of approved make fixed with CP brass screws etc. complete as directed.

Providing and constructing square mouth 100 mm dia. PVC Bottle gully trap grade “A” complete with CI grating including excavation, foundation concrete BBCC 1:5:10(1 part cement, 2 part coarse sand, 4 part of brickbat) 230 mm thick masonry, in Cement Mortar(CM) 1:6(1 part cement, 6 part coarse sand), cement mortar 1:3 (1 part cement,3 part coarse sand) plaster, neat cement finish and back filling etc. and water tight CI cover with frame of (300x300) mm size (inside),the weight of cover be not less than 4.5 kg and frame to be not less than 2.70 kg as per standard design complete as directed.

Providing and laying 150 mm diameter “Foamcore” uPVC pipe of approved first quality having rating of 10Kg/SqCm suitable for residential and commercial drain, waste, vent piping etc having stiffness classes such as SN4 and SN8 for underground applications including all necessary fittings, excavation of trenches up to required depth, providing & laying 150 mm thick BBCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part brickbat) as bedding, laying and jointing the pipe in line and level, with CM 1:1 (cement: sand) and jute fibres, curing, encasing with PCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part stone aggregate) all around of the pipe, refilling of the trenches, testing etc. complete as directed - Encasing of the pipe line with PCC 1:5:10 will be paid separately under relevant item.

Providing and fixing for both side polished, single piece minimum 18 mm thick Granite stone pardi with machine cut edges and cut to required shape etc. complete as directed.

Providing and Fixing 15 mm dia Central hole mixer for wash basin without popup waste system with 450 mm long Copper Pipe & Brass Nuts of approved make

Providing and Fixing sensor electrical operated automatic flushing system for urinals of approved make , including chrome sensor and female Box valve etc, complete in all respect including cutting and making good the walls wherever required as per approval of Engineer-in-charge

Providing and Fixing white vitreous china Water closet squatting pan (Indian type WC Pan) of approved make with 100 mm Sand cast iron P or S Trap set in cement concrete 1:2:4 (1 Cement: 2 Coarse sand: 4 Graded stone aggregate 20 mm nominal size), 6 Ltrs low level Vitreous china flushing Cistern with manually controlled device (Push button) 32 mm dia Flush pipe, rubber adopter with all fittings & fixtures complete including cutting and making good the walls and floors wherever required.

Providing and Fixing Electric Hand dryers, fully automatic, metal body in powder coating S.S. Finish of approved make

Providing and fixing C.P brass toilet paper roll holder with cover complete, including cutting and making good the walls wherever required of approved make

Providing and fixing C.P. Brass Coat Hook fixed with P.V.C. cleats with C.P. Brass screw all complete

Providing and Fixing CP Health Faucet (Hand Shower) with 1 mt: flexible tube and Wall Hook complete of approved make

Providing and making khurras with average minimum thickness of 5cm cement concrete 1:2:4 (1 cemet: 2 course sand: 4 graded stone aggregate 20mm nominal size) over PVC sheet 1m x 1m (PVC 400 microns min. thickness) finished with 12mm cement plaster 1:3 ( 1cement: 3 course sand, admixed with waterproofing compound) and a coat of neat cement, rounding the edge and making & finishing the outlet complete. Khurra size 300mm x 300mm, for 100mm dia outlet with 5mm thick circular/ square vertical C.I. grating.

Providing and constructing square or circular mouth 100 mm dia. PVC gully trap of approved make having size around 160mm X 110mm including rising piece, PVC grating. Gully trap shall be having one outlet and three closed inlets, seal traps, etc all for domestic and industrial grade, including excavation, foundation concrete BBCC 1:5:10(1 part cement, 2 part coarse sand, 4 part of brickbat) 230 mm thick masonry, in Cement Mortar (CM) 1:6 (1 part cement, 6 part coarse sand), cement mortar 1:3 (1 part cement,3 part coarse sand) plaster, neat cement finish and back filling etc. and water tight PVC cover with frame of suitable size (inside) etc complete as per the design complete as directed.

Providing and fixing square mouth 'P' type S.W gully trap grade ‘A‘ of size 150x100mm complete with C.I grating, brick masonry chamber and water tight C.I cover with frame of 300 x 300 mm size. The weight of cover to be not less than 4.50 Kg and and frame to be not less than 2.70 Kg as per standard design and detail.

Providing and fixing factory made grade SS 304 deep seal ' P' trap / Amul Trap in single piece without side joints of self cleansing design with or without vent arm with provision for connecting inlet fitting complete including cost of cutting and making good the walls and floors wherever required for 100mm inlet and 100mm outlet.

Supply and filling brick bat in soak pit, sunken portion of toilet etc. complete.

Constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 450x450x450mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Extra over & above for constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 450x450 & depth beyond 450mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 600x600x600mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Extra over & above for constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 600x600 & depth beyond 600mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 750x750x750mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Extra over & above for constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 750x750 & depth beyond 750mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 900x900x900mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Extra over & above for constructing brick masonry catch basin with bricks (35 Kg/sqcm compressive strength) in cement mortar 1:4(1 cement: 4 coarse sand), 200m thick foundation concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) inside and outside plaster in cement mortar 1:3 (1 cement: 3 coarse sand). inside finished with floating coat of neat cement, making haunches and channel in cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) neatly finished, complete as per standard design including excavation, refilling and disposal of surplus earth. For Size 900x900 & depth beyond 900mm inside with approved precast grating of approved design and sample fixed in RCC slab in cement 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20mm nominal size) including centering, shuttering all complete as per site conditions.

Providing & Fixing 6mm HDPE sheet lining in manhole including cutting welding & placing in position in manhole etc. complete.

Providing and fixing 125mm PVC Nahani trap (floor trap) self cleaning design with outlet size 75mm dia of approved make with perforated PVC jali including cutting the floor and fixing trap in CC 1:2:4 (1part of cement; 2 part of course sand; 4 parts of course aggregate) making good the floor, including connecting with drain pipes, sealing with rubber gaskets, fixing of top tile & strainer of chromium plated on top of the trap etc. complete as directed.

Providing and fixing heavy duty HD-20 grade designation SFRC manhole covers and frame of 560mm internal diameter confirming to IS:12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 mix (1 cement : 2 course sand : 4 graded stone aggregate 20mm nominal size) including centering and shuttering all complete.

Providing and fixing Stainless Steel Perforated trap cover of 150 X 150 mm (minimum 18SWG) into Floor tile including cutting of tile, silicon filling for water proofing, etc. complete over P trap or Nahni trap.

Providing and fixing uPVC type B Ring fit SWR Pipe of ISI mark of following diameters at all levels, including any/all type fittings, Multi floor trap, P -traps heavy duty specials (fittings) of ISI mark, with specialized joint, rings, fitting Concealed or open on wall/ RCC with all necessary chasses (jharies in walls) for laying pipe line in masonry or Open on wall with standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , testing after installation of pipe ,making holes, cutting floors, making good the walls and floors etc. complete as directed for 110mm OD.

Providing and fixing uPVC type B Ring fit SWR Pipe of ISI mark of following diameters at all levels, including any/all type fittings, Multi floor trap, P -traps heavy duty specials (fittings) of ISI mark, with specialized joint, rings, fitting Concealed or open on wall/ RCC with all necessary chasses (jharies in walls) for laying pipe line in masonry or Open on wall with standard pattern holders bat clamps made out of MS flat carrier fixed with bolts in the RCC or brick masonry and “C” clamp fixed to secure the pipe with GI bolts / screws / washers of required shape and size so as to fit tightly on the pipes when tightened with screwed , testing after installation of pipe ,making holes, cutting floors, making good the walls and floors etc. complete as directed for 160mm OD.

Providing and laying uPVC Eco drain or Fome Core SN8 pipe of approved quality including all necessary fittings, excavation of trenches in soil/murum up to 1500mm depth, providing & laying 150 mm thick BBCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part brickbat) as bedding, laying and jointing the pipe in line and level as per manufacturer's specification with PCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part stone aggregate) all around of the pipe, refilling of the trenches, testing before concealed the pipe etc. complete as directed. Encasing of the pipe line with PCC 1:5:10 will be not be paid separately for 110 mm OD.

Providing and laying uPVC Eco drain or Fome Core SN8 pipe of approved quality including all necessary fittings, excavation of trenches in soil/murum up to 1500mm depth, providing & laying 150 mm thick BBCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part brickbat) as bedding, laying and jointing the pipe in line and level as per manufacturer's specification with PCC 1:5:10 (1 part cement, 5 part coarse sand, 10 part stone aggregate) all around of the pipe, refilling of the trenches, testing before concealed the pipe etc. complete as directed. Encasing of the pipe line with PCC 1:5:10 will be not be paid separately for 160 mm OD.

Providing and fixing CI circular Manhole cover with frame of minimum 455 mm dia weighing minimum 60 kg (double seal) with confirming to IS etc complete as directed.

Extra charges for additional depth for providing and constructing Inspection Chambers/ Manhole Chamber/ any other Chamber as per the size as following including necessary excavation for additional depth in soil/murrum/rock and working space all around, providing and constructing of minimum 350mm thick brick/cement concrete block masonry walls in CM 1:4 (1 part cement and 4 parts of coarse sand) for the additional depth/height, providing and applying 15mm thick water proof plaster in CM 1:3 (1 part cement and 3 parts of coarse sand) added with integral waterproofing compound as per manufacturers specifications and finished with a floating coat of neat cement @ 2.2 Kg/SqM at the internal & external faces all around for the additional masonry walls etc complete as directed. Extra charges for additional depth for manhole chambers of clear internal dimensions as 1200mm X 1200mm (Square shaped). It shall be measured in RM or part thereof for the additional depth/height of the Manhole Chamber.

Providing fabricating and installing at all levels and in position (for dairy effluent drainage) Stainless Steel (SS) pipes Grade-304, 100mm to 200mm dia and wall thickness from 2mm to 3mm including all types of necessary fittings such as elbows, bends, reducer bends, reducers, reducer tees, tees, TC ends, SS flanges with nuts and bolts, SS caps etc, piping work shall be carried out in verticals and horizontals and also fixed to stainless steel drain traps including providing and fixing of approved heavy duty SS 304 grade pipe brackets (made from SS 304 flats up to 50mm wide and up to 6mm thick) and anchoring arrangement by providing and fixing self-expansion fasteners of 12mm dia X 100/120mm long sized of approved make fixed with RCC (concrete) elements, all fixing accessories, all cutting, bending, welding, grinding, drilling, tapping, weep hole and all other incidentals, and approved buffing to stainless steel members, including all scaffolding and staging etc. complete as directed. SS Pipes and SS bracket supports actually fixed in position as per the drawing and as directed shall be measured and paid in KG. Wastages shall not be paid.

Providing and laying 250 mm diameter non-pressure class NP2 RCC Hume pipes with collars including excavation of trenches in soil/murum/rock, laying the pipes as per layout and drawing, filling the joints with stiff mixture of cement mortar (1 part cement :1part fine sand) and jute, curing, testing the pipe and refilling the trenches in layers with due compaction & watering etc. complete as directed

Providing and fixing Flush Valve of 40mm dia size (concealed body) with exposed shut off provision of approved make including cutting and making good the walls etc complete as directed

Providing and fixing large flat back white glazed first quality urinal of approved make with all fixing accessories including Chrome Plated (CP) auto closing concealed urinal flush valve with wall flange of approved make including the required length of 40 mm dia. cPVC waste pipe to be laid concealed in wall up to floor drain with plain and brass threaded bends concealed in wall etc complete as per the recommendations of manufacturer and as directed.

Providing and fixing First quality wall mounted European type white glazed vitreous china Water Closet of size 495mm X 350mm X 335mm of approved make including all accessories and fixing with CI chair brackets or SS fastners as per the recommendation of manufacturer, seat cover of approved make, Flush Valve of 40mm dia Size (concealed body) with exposed shut off provision of approved make, Hand shower (Health Faucet) with 8mm dia 1.2 meter long easy flex tube in chrome finish of approved make & CP wall hook, Rack Bolts, braided connection pipe, two way bib cock with wall flange of approved make, cutting and making good the walls and floors, treating the joints with silicon joint etc complete as directed.

Providing & Construction of underground rain water re-charge well 4m internal dia with 2.0m water holding above the filtering media and below connection level of drainage line and desilting chamber with following specifications and including supplying, installation & execution of all jobs, complete as per drawings and directions of Engineer-in-Charge. Peripheral brick masonry in cement mortar 1:4 ( 1cement: 4 coarse sand) with necessary 15 mm thick cement plaster 1 :3 neat finish.Foundation concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) (200mm thick). Geo textile membrane, 200 mm thick sand (1.5 to 2 mm size), 100 mm thick activated carbon and 500 mm thick brick aggregate 40 to 63 mm size. 200mm thick R.C.C. slab in M20 mix to cover the well at top including necessary centring, shuttering and reinforcement with required openings /cutouts etc. complete in all respects. Desilting chamber 1500x1000x900mm deep from connection level in brick masonary, foundation concrete and RCC slab as above complete in all respects as per drawing.Supplying and fixing PVC coated M.S. foot rests. Making all inlets & outlets in brick masonry walls including cutting holes& making good the same. 10- 12 mm thick cement plaster 1 :3 ( 1 cement : 3 fine sand ) mixed with water proofing compound on top of R.C.C slab, finished smooth. 2 Nos. 560 mm dia SFRC heavy duty conforming to IS 12592 manhole cover in top slab. 200mm dia PVC plain/perforated solid pipe laid vertically upto 30 meters below bottom of harvesting well, including necessary drilling/ boring in ground in all kinds of soil as directed by the Engineer-in-charge.Rate to include excavation back filling, disposal of surplus excavated soil with all leads and all other materials & operations necessary for completing the job. Note: Refer Sketch-STR - INF - 02

Providing, fabricating and fixing in position 8 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 10 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 12 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 16 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 20 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 25 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing, fabricating and fixing in position 32 mm dia. TMT reinforcement steel bars of minimum grade Fe 415 confirming to IS 1786 - 1985 of approved or equivalent make for RCC structures as per design including transporting, unloading and incidental charges for handling cutting, bending, and binding with two strands of annealed steel wire of 18 gauge, welding if necessary etc. complete as directed. Note:-Approved make TMT reinforcement steel bar shall conform to IS 1786 shall be Fe 500 or higher grade.

Providing and fixing/ laying of conduit and wires for Light point wiring with 1.5 sq. mm PVC insulated, FRLS, copper conductor (stranded) 1100V grade wires alongwith earthing in 25mm dia. medium duty PVC surface/ concealed conduit system including providing and fixing one no. 10 Amp single pole modular switch grid plate mounted with moulded cover plate in zinc chromate passivated GI box suitable for modular switch, complete in all respect (wiring & conduiting up to switchboard not included in item cost), for one light point controlled by one switch. Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit and wires for Light point wiring with 1.5 sq. mm PVC insulated, FRLS, copper conductor (stranded) 1100V grade wires alongwith earthing in 25mm dia. medium duty PVC surface/ concealed conduit system including providing and fixing one no. 10 Amp single pole modular switch grid plate mounted with moulded cover plate in zinc chromate passivated GI box suitable for modular switch, complete in all respect ( wiring & conduiting up to switchboard not included in item cost), for two light points controlled by one switch. Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit and wires for Light point wiring 1.5 sq. mm PVC insulated, FRLS, copper conductor (stranded) 1100V grade wires alongwith earthing in 25mm dia. medium duty PVC surface/ concealed conduit system including providing and fixing one no. 10 Amp single pole modular switch grid plate mounted with moulded cover plate in zinc chromate passivated GI box suitable for modular switch, complete in all respect ( wiring & conduiting up to switchboard not included in item cost), for three light points controlled by one switch. Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit and wires for Light point wiring with 1.5 sq. mm PVC insulated, FRLS, copper conductor (stranded) 1100V grade wires alongwith earthing in 25mm dia. medium duty PVC surface/ concealed conduit system including providing and fixing one no. 10 Amp single pole modular switch grid plate mounted with moulded cover plate in zinc chromate passivated GI box suitable for modular switch, complete in all respect (wiring & conduiting up to switchboard not included in item cost), for controlled by 2 nos. 2 way switch. Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit and wires for Ceiling fan point wiring with 1.5 sq. mm PVC insulated, FRLS, Cu. conductor (stranded) 1100V grade wires alongwith earthing in 25 mm dia. Medium duty PVC surface/ concealed conduit system including providing and fixing one no. modular 10A single way switch, grid plate mounted with moulded cover plate, two module electronic stepped fan regulator in zinc chromate passivated GI box suitable for modular switches, with GI box for fan suspension, complete in all respect ( wiring & conduiting up to switchboard not included in item cost). Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit and wires for Exhaust / Brackate fan point wiring with 1.5 sq. mm PVC insulated, FRLS, Cu. conductor (stranded) 1100V grade wires alongwith earthing in 25 mm dia. Medium duty PVC surface/ concealed conduit system including providing and fixing one no. modular 10A single way switch, grid plate mounted with moulded cover plate in zinc chromate passivated GI box suitable for modular switches complete in all respect ( wiring & conduiting up to switchboard not included in item cost). Including making zaries in the wall and finishing the same.

Providing and fixing/ laying of conduit & wires for Buzzer point wiring with 1.5 sq. mm. PVC insulated, FRLS, Cu. conductor 1100V grade wires in 25 mm dia Medium duty PVC concealed/ surface conduit system including providing and fixing one no. 10 Amp modular buzzer push button, grid plate mounted with moulded cover in zinc chromate passivated GI box suitable for modular switches ( wiring & conduiting up to switchboard not included in item cost) complete in all respect. Including making zaries in the wall and finishing the same.

Providing and fixing zinc chromate passivated GI box suitable for modular switches with grid plate moulded cover , in surface / concealed conduit system and 1 no. 10 A 3 pin 250 V modular socket outlet with safety shutter and 10 A 250 V modular switch for 10 A isolated power point (wiring & conduiting up to power plug point not included in item cost) complete in all respect. Including making zaries in the wall and finishing the same.

Providing and fixing 10A 3 pin 250 V modular socket outlet and 10 A 250 V modular switch in existing lighting switch board, including connections within the box with 1.5 sq. mm PVC insulated, FRLS copper conductor 1100 V grade wires. (wiring & conduiting up to power plug point not included in item cost) Including making zaries in the wall and finishing the same.

Providing and fixing zinc chromate passivated GI box with moulded sheet cover in surface/concealed conduit system and 1 no. modular 20 A 3 pin 250 V universal socket outlet with safety shutter and 20 A 250 V modular type switch for 20 A isolated power point (wiring & conduiting up to power plug point not included in item cost) complete in all respect. Including making zaries in the wall and finishing the same.

Providing & fixing 10 A single way modular switch and 10A, 3 pin modular socket with safety shutter, in existing channel of modular furniture. (No wiring, conduiting up to power plug & GI box cost to be considered in item) Including making zaries in the wall and finishing the same.

Providing and fixing zinc chromate passivated GI boxes with moulded sheet cover in surfaces/concealed conduit system for 20 A power point (socket and switch are separated from each other by a distance of 2 mtr. Max). In one box 20 A universal 6 pin 250 V modular type socket outlet having safety shutter to be fixed and in other 1 no. 20 A 250 V modular type switch to be fixed. Both the boxes to be interconnected with surface/ concealed conduit system with 2.5 sq. mm. PVC insulated FRLS, Cu conductor (stranded), 1100 V grade wires and 2.5 sq. mm. Green PVC insulated earth wire. (Cost of wiring and conduiting up to the first box from DB is not included in this item cost). Including making zaries in the wall and finishing the same.

Circuit wiring with PVC insulated, FRLS, 1100V grade, Cu. conductor (stranded) wires of red/blue/yellow colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/concealed conduit system, complete with wires and conduit sizes of 2 x 2.5 Sq. mm for power (phase & neutral) and 1 x 1.5sq mm for earthing in 25 mm dia medium duty PVC conduit. Including making zaries in the wall and finishing the same.

Circuit wiring with PVC insulated, FRLS, 1100V grade, Cu. conductor (stranded) wires of red/blue/yellow colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/concealed conduit system, complete with wires and conduit sizes of 2 x 4.0 sq. mm. for power (phase & neutral) and 1 x 2.5 sq. mm for earthing in 25 mm dia Medium duty PVC conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Circuit wiring with PVC insulated, FRLS, 1100V grade, Cu. conductor (stranded) wires of red/blue/yellow colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/concealed conduit system, complete with wires and conduit sizes of 4 x 2.5 sq. mm. for power (phases & neutral) and 2 x 2.5 sq. mm for earthing in 25 mm dia Medium duty PVC conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Sub main wiring (1 PHASE) with PVC insulated, FRLS, Cu. Conductor (stranded) 1100V grade wires of red/yellow/blue colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/ concealed conduit system complete with wires and conduit of size 2x6sq. mm. For power and 1x4 sq. mm for earth wire in 25 mm dia conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Sub main wiring (1 PHASE) with PVC insulated, FRLS, Cu. Conductor (stranded) 1100V grade wires of red/yellow/blue colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/ concealed conduit system complete with wires and conduit of size 2x10 sq. mm for power (phase & neutral) and 1x6 sq. mm for earth wire in 25 mm dia Medium duty PVC conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Sub main wiring (3 PHASE) with PVC insulated, FRLS, Cu. Conductor (stranded) 1100V grade wires of red/yellow/blue colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/ concealed conduit system complete with wires and conduit of size 4x6 sq. mm for power (phases & neutral) and 2x4 sq. mm for earth wire in 32 mm dia Medium duty PVC conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Sub main wiring (3 PHASE) with PVC insulated, FRLS, Cu. Conductor (stranded) 1100V grade wires of red/yellow/blue colour for phase, black colour for neutral & green colour for earthing in Medium duty PVC surface/ concealed conduit system complete with wires and conduit of size 4x10 sq. mm for power (phases & neutral) and 2x6 sq. mm for earth wire in 38 mm dia Medium duty PVC conduit. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface 25 mm dia Medium duty PVC conduit for wiring complete with accessories and draw out boxes and their covers. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface 32 mm dia Medium duty PVC conduit for wiring complete with accessories and draw out boxes and their covers. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface 38 mm dia Medium duty PVC conduit for wiring complete with accessories and draw out boxes and their covers. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface GI pipe class `A' in slab/ floor/ wall/ ground etc. with accessories and draw out boxes and their covers of Pipe size -- 25 mm dia. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface GI pipe class `A' in slab/ floor/ wall/ ground etc. with accessories and draw out boxes and their covers of Pipe size -- 38 mm dia. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & laying spare concealed or surface GI pipe class `A' in slab/ floor/ wall/ ground etc. with accessories and draw out boxes and their covers of Pipe size -- 51 mm dia. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & laying enclosed metal raceways fabricated from 14 SWG galvanised sheet steel with cover screwed on top with counter sunk screws & complete with neoprene gaskets, complete & finish with finished floor level as required. Size 50 mm wide & 40 mm deep. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supplying & laying enclosed metal junction boxes for raceways fabricated from 14 SWG galvanised sheet steel with cover screwed on top with counter sunk screws & complete with neoprene gaskets & powder coated finish, complete & finished with finished floor, size 150X150 mm wide & 50 mm deep Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & pulling of 1.5 sq. mm. PVC insulated, FRLS, copper conductor (stranded) wire, 1100 V grade, in existing conduit/ GI pipe/ raceways/ modular furniture. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & pulling of 2.5 sq.mm PVC insulated, FRLS, copper conductor (stranded) wire, 1100 V grade, in existing conduit/ GI pipe/ raceways/ modular furniture. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & pulling of 4.0 sq.mm PVC insulated, FRLS, copper conductor (stranded) wire, 1100 V grade, in existing conduit/ GI pipe/ raceways/ modular furniture Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & pulling of 6.0 sq.mm PVC insulated, FRLS, copper conductor (stranded) wire, 1100 V grade, in existing conduit/ GI pipe/ raceways/ modular furniture Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & pulling of 10.0 sq.mm PVC insulated, FRLS, copper conductor (stranded) wire, 1100 V grade, in existing conduit/ GI pipe/ raceways/ modular furniture. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing and fixing GI slotted angle cable trays(height 50 mm, thickness 1.5 mm ) with M S supports and anchor fasteners etc. as required, of size - 100 mm wide.

Providing and fixing GI slotted angle cable trays(height 50 mm, thickness 1.5 mm ) with M S supports and anchor fasteners etc. as required, of size - 200 mm wide.

Providing and fixing GI slotted angle cable trays(height 50 mm, thickness 1.5 mm ) with M S supports and anchor fasteners etc. as required, of size - 300 mm wide.

Providing and fixing zinc chromate passivated MS Box with grid plate moulded cover , in surface / concealed conduit system and 3 nos. 6 A 3 pin 250 V modular socket outlet with safety shutter and 1 no. 6 A 250 V modular switch for 6 A power point (wiring & conduiting up to power plug point not included in item cost) complete in all respect.

Providing and fixing 6A 3 pin 250 V modular socket outlet and 6 A 250 V modular switch in existing lighting switch board, including connections within the box with 1.5 sq. mm PVC insulated, FRLS copper conductor 1100 V grade wires. (wiring & conduiting up to power plug point not included in item cost)

Providing and fixing zinc chromate passivated MS Box with moulded sheet cover in surface/concealed conduit system and 1 no. modular 16 A 6 pin 250 V universal socket outlet with safety shutter and 16 A 250 V modular type switch for 16 A isolated power point (wiring & conduiting up to power plug point not included in item cost) complete in all respect.

Providing and fixing zinc chromate passivated MS boxes with moulded sheet cover in surfaces/ concealed conduit system for 16 A power point (socket and switch are separated from each other by a distance of 2 mtr. Max). In one box 16 A universal 6 pin 250 V modular type socket outlet having safety shutter to be fixed and in other 1 no. 16 A 250 V modular type switch to be fixed. Both the boxes to be interconnected with surface/ concealed conduit system with 4.0 sq. mm. PVC insulated FRLS, Cu conductor (stranded), 1100 V grade wires and 2.5 sq. mm. Green PVC insulated earth wire. (Cost of wiring and conduiting up to the first box from DB is not included in this item cost).

Supplying & laying enclosed metal junction boxes for raceways fabricated from MS sheet with cover screwed on top with counter sunk screws & complete with neoprene gaskets & powder coated finish, complete & finished with finished floor, size 250X250 mm wide x 75 mm deep.

230V/24 or 12 V SMPS with all protections in enclosure

Providing and fixing/laying of conduit and wires for Bell point controlled by Bell push switch with Buzzer / bell of approved make. (including making & finishing of zari)

Installation, testing & commissioning of lighting fixtures suitable for compact fluorescent/ LED lamp, directly on ceiling/beams/walls/ trusses etc. without any extra clamps or additional fixing device complete with all accessories including lamps and connecting with 1.5 sq mm Cu. Conductor wire from light points.

Installation of recess mount light fixture in false ceiling having 600X600mm tiles by providing 6 mm thick water and termite proof plywood sheet (size: 590X590 mm) with suitable cutout in plywood and tile. Item includes connection and testing of light fixture.

Installation, testing and commissioning of ceiling/ bracket fan, with all standard accessories and connecting with 1.5 sq mm Cu. conductor PVC wires.

Installation, testing and commissioning of ceiling/ bracket fan, with all standard accessories and connecting with 1.5 sq mm Cu. conductor PVC wires. The standard hanging rod of ceiling fan to be replaced with new GI class `B' pipe up to 700 mm long. (including painting of new pipe)

Installation, testing and commissioning of ceiling/ bracket fan, with all standard accessories and connecting with 1.5 sq mm Cu. conductor PVC wires. The standard hanging rod of ceiling fan to be replaced with new GI class `B' pipe above 700 mm and up to 1500 mm long (including painting of new pipe)

Installation, testing & commissioning of exhaust fan up to 450 mm size with all accessories in existing opening in wall and connecting with 2.5 sq mm Cu. conductor PVC flexible cable with flexible conduit from exhaust fan point.

Fixing, testing and commissioning of bell/ buzzer/ musical bell/bell indicator on buzzer point.

Making opening in wall including finishing in all respects for exhaust fan up to 300 mm size.

Making opening in wall including finishing in all respects for exhaust fan up to 450 mm size.

Providing & fixing approved suitable MS clamps with bolts-nuts etc. for fixing fluorescent lamp / LED lamp fittings directly on steel truss, including painting of clamps.

Providing suitable MS box section bracket of size 50X50X1.6 / 2 mm thick duly painted with approved shade and fixing with anchor fastener for installing light fittings in beams / walls as directed.

Installation, testing and commissioning of any Type Recessed Mounted LED Down Light Fixture with all required accessories (including making cutout/hole in PUF/gypsum/metallic type false ceiling)

Installation, testing and commissioning of any Type Surface Mounted LED Down Light Fixture with all required accessories.

Installation, testing and commissioning of 2' x 2' Squre Surface Mounted Light Fixture with all required accessories.

Installation, testing and commissioning of Flood Light Fixture with all required accessories.

Supply & installation of street light bracket, fabricated from mild steel medium class pipe ERW type, of 50 mm NB ,1.8 m long having 500 mm vertical &1300 mm bent, with MS/ Thermoplastic switch box of apprx. size 250x200x80 mm having 30A 4 way connector for power, 30A 4 way connector for neutral, 10 A SP MCB. and concealed/ surface conduit( Maximum 5.0 m ) between MS/ Thermoplastic box and bracket for wiring .

Supply & installation of High Mast, fabricated out of special steel plates conforming to BS-EN10-025 only one longitudinal seam weld per section alongwith Lantern Carriage , cast aluminium juction box, self sustaining Winch arrangement for lowering and raising the Lantern Carriage Assembly, head frame, styainless wire ropes of AISI 316 grade, cables and lighting finial, earth pits alongwith Light Fittings complete. Tower to be complete with painting & details as per technical specification Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Supply & installation of pole for post top lantern fitting, fabricated from MS `B' class ERW pipe,65 mm NB 1.0 M long with MS/ thermoplastic switch box of apprx. size 250X200X80 MM having 30 A 4 way connector for power, 30 A 4 way connector for neutral, 10 A SP MCB & 25 mm steel conduit between MS box & pole for pulling wires ,complete in all respects. FOR ENTRANCE GATE

Supply & installation of pole for post top lantern fitting, fabricated from MS `B' class ERW pipe,65 mm NB 3.5 M long with MS/ thermoplastic switch box of apprx. size 250X200X80 MM having 30 A 4 way connector for power, 30 A 4 way connector for neutral, 10 A SP MCB ,complete in all respects., 1:2:4 Concrete foundation pedestal of size 300x300x1000 mm included in the scope of installation - FOR OPEN GROUND.

Fixing, testing & commissioning light fixture on street light pole including wiring from switch box to fixture with 3x2.5 sq. mm copper conductor, FRLS, PVC insulated and sheathed flexible cable.

Fixing, testing & commissioning light fixture on street light pole bracket on building including wiring from switch box to fixture with 3x2.5 sq. mm copper conductor, FRLS, PVC insulated and sheathed flexible cable.

Fixing, testing & commissioning light fixture on pole but for post top lantern at gate, including wiring from switch box to fixture with 3x2.5 sq. mm copper conductor, FRLS, PVC insulated and sheathed flexible cable.

Fixing, testing & commissioning light fixture on pole for post top lantern in open ground, including wiring from switch box to fixture with 3x2.5 sq. mm copper conductor, FRLS, PVC insulated and sheathed flexible cable.

Fixing, testing and commissioning flood light fitting on steel tower including wiring from bottom MS switch box (near road level)of tower to fitting through control gear box(near light fittings) with 3x4.0 sq. mm copper conductor, PVC insulated, FRLS, sheathed flexible cable in steel conduit.

Fixing, testing & commissioning of flood light fitting on building top, including providing switch M S box (near road level)and wiring from switch box to fitting with 3x4.0 sq.mm copper conductor, PVC insulated, FRLS, sheathed flexible cable in steel conduit.

Supply and installation of hot dip galvanized polygonal/ octagonal street light pole 6500 MM long with foundation bolts, switch box with 30A, 4 way connector for phase, & neutral, 10 A SP MCB, GI earthing pipes, earthing wires etc complete as per the detail drawing and technical specification with single arm on top. The rate of the Item also includes the cost of excavation in ground for pole foundation, Reinforcement Steel, Cement concrete of 1:2:4 grade, necessary shuttering, bed concrete with PCC (1:4:8), back filling of excavated earth, water curing of concrete for 7 days, supply & laying of “A” Class GI pipes in the foundation for laying wires/Cables and earthings, etc. complete as directed and as per the drawing.

Supply and installation of hot dip galvanized polygonal/ octagonal street light pole 6500 MM long with foundation bolts, switch box with 30A, 4 way connector for phase, & neutral, 10 A SP MCB, GI earthing pipes, earthing wires etc complete as per the detail drawing and technical specification with double arm on top. The rate of the Item also includes the cost of excavation in ground for pole foundation, Reinforcement Steel, Cement concrete of 1:2:4 grade, necessary shuttering, bed concrete with PCC (1:4:8), back filling of excavated earth, water curing of concrete for 7 days, supply & laying of “A” Class GI pipes in the foundation for laying wires/Cables and earthings, etc. complete as directed and as per the drawing.

Providing maintenance free, Chemical type earthing pit including filling compounds, accessories and civil work complete as per IS 3043-1987 latest revision ( Hotdip GI electrode in GI pipe) Specification: GI pipe : 80 mm dia, 3 mtr long and 3 mm thickness, Hotdip GI electrode: 50 X 10 mm

Providing maintenance free, Chemical type earthing pit including filling compounds, accessories and civil work complete as per IS 3043-1987 latest revision (Copper electrode in Copper pipe) Specification: GI pipe : 50 mm dia, 3 mtr long and 3 mm thickness, Copper flat electrode: 25 X 6 mm

Providing and laying earth continuity conductor in ground/ on surface of building with necessary clamps as required, of size – GI strip 50X6mm

Providing and laying earth continuity conductor in ground/ on surface of building with necessary clamps as required, of size – GI strip 25X3mm

Providing and laying earth continuity conductor in ground/ on surface of building alongwith pipe with necessary clamps as required, of size – GI wire 8 SWG in 19mm A class GI pipe

Providing and laying earth continuity conductor in ground/ on surface of building with necessary clamps as required, of size – GI wire 8 SWG

Providing & laying earth continuity conductor in ground/on surface /concealed of building alongwith pipe as required with Al. Conductor wire(single core), 10 square mm, PVC insulated of black colour in 19mm ‘A’ class GI pipe.

Providing & laying earth continuity conductor in ground/on surface /concealed of building as required with Al. Conductor wire(single core), 10 square mm, PVC insulated of black colour.

Providing and fixing lightening arrestor made of 25 mm dia 1200 mm long CU tube having a multiple spikes at the top with thick CU base plate/ saddling & clamping complete as required. Note : 30 m motorized high mast pole suitable for 50 m/sec Note : Minimum 5 spikes to be provided. Including copper electrode(pipe in pipe, 3 mtr long) type earth pit and copper strip of 25 x 3 mm.

Providing & laying earth roof conductor for earthing, CU strip 25x3 mm complete with clamps etc.

Providing Chemical Earthing Pit similar to Fast Earth Electrode Model F-63 (3Mtr rod with 2 Bag of 25 Kgs GREP Compound) Two M.S. pipes one inside the other with proper hot deep galvanization outer dia 62 mm & inner dia 32 mm. The cavity between the rod pipes is filled with Ground Resistance Improvement Powder. The electrode should be sealed from both the ends. The outer Pipe of the electrode should be zinc coated. Each Electrode should be supplied with bags of GRIP Compound (Ground Resistance Improvment Powder). The Characteristics of this compound is highly conductive, non magnetic & non corrosive in nature. Including all accessories, and civil work complete as per IS 3043-1987 latest revision.

Providing and fixing/laying of conduit and wires for 1 Telephone point in one box wiring (from telephone tag box to point ) with 4 pair, un-armoured, PVC insulated and sheath, 0.51 mm dia. Annealed tinned Cu conductor in 25 mm Medium duty PVC surface/ concealed conduit system including providing and fixing one no. flush type RJ11 modular telephone socket outlet, grid plate mounted with moulded cover plate in zinc chromate passivated GI box. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits as per site condition, Including making zaries in the wall and finishing the same.

Providing & fixing/laying of wires for telephone point wiring with 4 pair un-armoured PVC insulated sheath, 0.51 mm dia, annealed tinned Cu conductor cable in existing conduit /raceways /modular furniture.

Providing & fixing one no flush type RJ11 telephone socket outlet grid plate mounted with moulded cover in zinc chromate passivated GI box.(No cost for wire & conduit to be included)

Providing & laying Wires for computer /telephone points with CAT – 6, 4 pair copper conductor UTP cable in existing conduit/raceways/ modular furniture

Providing & fixing of a single computer data grid plate mounted outlet unit suitable for CAT-6 Cable with moulded cover plate in recessed zinc chromate passivated GI box complete as required for computer networking system. (No cost for wire & conduit to be included)

Providing & fixing of a single computer data grid plate mounted outlet unit suitable for CAT-6 Cable provided in modular furniture. (No cost for wire & conduit to be included)

Providing jelly filled armoured telephone cable , PVC insulated and sheathed , 0.51 mm dia annealed tinned copper conductor Telephone cable size - 10 pair.

Providing jelly filled armoured telephone cable , PVC insulated and sheathed , 0.51 mm dia annealed tinned copper conductor Telephone cable size - 20 pair.

Providing jelly filled armoured telephone cable , PVC insulated and sheathed , 0.51 mm dia annealed tinned copper conductor Telephone cable size - 50 pair.

Providing and fixing KRONE type telephone tag block with GI box with prefabricated powder coated or Thromoplastic box , suitable for 10 pairs.

Providing and fixing KRONE type telephone tag block with GI box with prefabricated powder coated or Thermoplastic box , suitable for 20 pairs.

Providing and fixing KRONE type telephone tag block with GI box with prefabricated powder coated or Thermoplastic box, suitable for 50 pairs.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated & sheath 0.51 mm dia annealed tinned Cu conductor, in underground system including excavation for trenches ,providing bricks & sand etc., identification of pairs and connection in tag block at both ends. (COST OF CABLE NOT INCLUDED IN THIS ITEM) Up to 10 pair telephone cable.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated & sheath 0.51 mm dia annealed tinned Cu conductor, in underground system including excavation for trenches ,providing bricks & sand etc., identification of pairs and connection in tag block at both ends. (COST OF CABLE NOT INCLUDED IN THIS ITEM) Up to 20 pair telephone cable.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated & sheath 0.51 mm dia annealed tinned Cu conductor, in underground system including excavation for trenches ,providing bricks & sand etc., identification of pairs and connection in tag block at both ends. (COST OF CABLE NOT INCLUDED IN THIS ITEM) Up to 50 pair telephone cable.

Providing and fixing TV cable outlet in zinc chromate passivated GI box with moulded modular sheet cover. (cost of TV cable wiring up to this box is not included in this item).

Providing and fixing/ laying of CAT-6, 4-pair, copper conductor, UTP cable with 25 mm Medium duty PVC concealed/ surface conduit system, as required.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated and sheathed, 0.51mm dia annealed tinned copper conductor in air (on cable tray/trenches/GI pipes etc.) with GI clamps, identification of pairs and connections in tag box at both ends. (COST OF CABLES, CABLE TRAYS, GI PIPE ETC. NOT TO BE INCLUDED IN THIS ITEM) - Telephone cable size - up to 10 pair.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated and sheathed, 0.51mm dia annealed tinned copper conductor in air (on cable tray/trenches/GI pipes etc.) with GI clamps, identification of pairs and connections in tag box at both ends. (COST OF CABLES, CABLE TRAYS, GI PIPE ETC. NOT TO BE INCLUDED IN THIS ITEM) - Telephone cable size - up to 20 pair.

Laying and connecting multi pair telephone cable armoured, jelly filled, PVC insulated and sheathed, 0.51mm dia annealed tinned copper conductor in air (on cable tray/trenches/GI pipes etc.) with GI clamps, identification of pairs and connections in tag box at both ends. (COST OF CABLES, CABLE TRAYS, GI PIPE ETC. NOT TO BE INCLUDED IN THIS ITEM) - Telephone cable size - up to 50 pair.

Supply , Installtion , Testing and comissioning of armoured 6 core Singlemode OFC cable for interfloor switch connectivity. Note : Includes PVC Surface/Concealed, GI Surface/Concealed conduits, DWC pipe, HDPE pipe, RCC hume pipe as per site condition, Including making zaries in the wall and finishing the same.

Supply, installation & commissioning of fabricated/ readymade cubicle type switchboard, totally enclosed, dust & vermin proof, floor mounted, as per specifications enclosed along with powder coating painting, complete with following major components/ switchgears, cable alleys, bus bars & inter-connections & rubber mat as per details of incoming & outgoing switchgear & components Note : Entry- BOTTOM/TOP ENTRY. As per specification, Approved makes & SLD.INCOMER :1 No. 400A, 4P MCCB, Ics=Icu=35 KA, with R,Y,B phase indication lamps, on / off /Trip indication lamps for all feeders , Digital MFM/energy meter, Digital Ammeter 0-400A with SS & CTs, Digital Voltmeter 0-500 V with SS. OUTGOING FEEDERS : with on/off/trip indication lamps for all MCCB outgoing feeders. 125A 4P MCCB-2 Nos,. 100A 4P MCCB-2 NOS, 80A 4P MCCB-6 NOS 63A 4P MCCB-6 NOS, 40 A DP MCB- 6 Nos., 20A DP MCB 4 Nos

Supply, installation & commissioning of fabricated / readymade MCB type electrical distribution board (SPN 12 WAYS) flush type, indoor enclosure, hinged front cover, dust & vermin proof, complete with switchgear given below and interconnection, as per detailed specification enclosed, along with powder coating painting. All MCB & RCCB/ELCB shall be of minimum 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 300 mA. Detail of incoming & outgoing switchgear & component enclosed

Supply, installation & commissioning of fabricated / readymade MCB type electrical distribution board (SPN16 WAYS) flush type, indoor enclosure, hinged front cover, dust & vermin proof, complete with switchgear given below and interconnection, as per detailed specification enclosed, along with powder coating painting. All MCB & RCCB/ELCB shall be of minimum 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 300 mA. Detail of incoming & outgoing switchgear & component enclosed

Supply, installation & commissioning of fabricated / readymade MCB type electrical distribution board (TPN 8 WAYS) flush type, indoor enclosure, hinged front cover, dust & vermin proof complete with switchgear given below and interconnection, as per detailed specification enclosed, along with powder coating painting. All MCB & RCCB/ELCB shall be of minimum 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 300 mA. Detail of incoming & outgoing switchgear & component enclosed Note : Detail of incoming & outgoing switchgear & component enclosed DB- 3 nos- (7 Segment )INCOMER :63A, 4P, MCB- 01 No., OUTGOING : 63A, 2P, ELCB / RCCB- 03 No., 10A to 20 A, SP, MCB - 24 nos-

Supply, installation & commissioning of fabricated / readymade MCCB type electrical distribution board (8 WAYS 3 PHASE OUT GOING) flush type, indoor enclosure, hinged front cover, dust & vermin proof complete with switchgear given below and interconnection, as per detailed specification enclosed, along with powder coating painting. All MCCB with min 25 KA and MCB/RCCB/ELCB shall be of min 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 300 mA. Detail of incoming & outgoing switchgear & component enclosed "Note : Detail of incoming & outgoing switchgear & component enclosed INCOMER : 100A, 4P, MCB- 01 No., OUTGOING : 100A, 2P, ELCB / RCCB- 03 No.,32A TPN MCB-3 Nos,. 10A to 20 A, SP, MCB - 15 nos."

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 4x4 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 2x10 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 4X10 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 4X16 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 4X25 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 3.5X35 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 3.5X70 sq mm.

Providing PVC insulated outer and inner PVC sheath, 1100 V grade, armoured Aluminium conductor cable (cable laying cost not included) -size of cable 3.5X120 sq mm.

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in underground including excavation, supply of bricks/sand etc. and providing and fixing cable glands and lugs at both ends as per specification. Near end of cable, if required GI pipe A class of suitable size to be provided without extra cost instead of laying cable in ground with bricks & sand. ( COST OF CABLE NOT TO BE INCLUDED IN THIS ITEM.) Cable size up to 16 SQMM.

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in underground including excavation, supply of bricks/sand etc. and providing and fixing cable glands and lugs at both ends as per specification. Near end of cable, if required GI pipe A class of suitable size to be provided without extra cost instead of laying cable in ground with bricks & sand.( COST OF CABLE NOT TO BE INCLUDED IN THIS ITEM.) Cable size above 16 sq. mm. up to 50 sq. mm.

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in underground including excavation, supply of bricks/sand etc. and providing and fixing cable glands and lugs at both ends as per specification. Near end of cable, if required GI pipe A class of suitable size to be provided without extra cost instead of laying cable in ground with bricks & sand.( COST OF CABLE NOT TO BE INCLUDED IN THIS ITEM.) Cable size above 50 sq. mm. up to 120 sq. mm.

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in air (on cable trays or GI Pipes etc.) including providing and fixing GI Cable clamps, cable glands and lugs at both ends as per specification (COST OF CABLE, CABLE TRAYS, GI PIPES NOT INCLUDED IN THIS ITEM.) Cable size upto 16 sq mm

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in air (on cable trays or GI Pipes etc.) including providing and fixing GI Cable clamps, cable glands and lugs at both ends as per specification (COST OF CABLE, CABLE TRAYS, GI PIPES NOT INCLUDED IN THIS ITEM.) Cable size above 16 sq. mm. up to 50 sq. mm

Laying of PVC insulated outer and inner PVC sheet 1100 V grade armoured Al. Conductor cable in air (on cable trays or GI Pipes etc.) including providing and fixing GI Cable clamps, cable glands and lugs at both ends as per specification (COST OF CABLE, CABLE TRAYS, GI PIPES NOT INCLUDED IN THIS ITEM.) Cable size above 50 sq. mm. up to 120 sq. mm

Supply, installation & commissioning of MCB type electrical distribution board (THREE PHASE AND NEUTRAL, 4 WAYS 1 PHASE OUTGOING) flush type, indoor enclosure, hinged front cover, dust & vermin proof, fabricated out of 16 G mild steel sheets and complete with switchgear given below and interconnection as per detailed specification along with powder coating painting. All MCB & RCCB/ELCB shall be of minimum 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 30 MA. (7 Segment). INCOMER : 63A, 4P, MCB - 1 NO., OUTGOING ; 63A , 2P, ELCB/ RCCB - 3 NOS ; 20A SP MCB - 12 NOS

Supply, installation & commissioning of electrical distribution board (THREE PHASE AND NEUTRAL, 6 WAYS 1 PHASE OUTGOING) flush type, indoor enclosure, hinged front cover, dust & vermin proof, fabricated out of 16 G mild steel sheets and complete with switchgear given below and interconnection, as per detailed specification along with powder coating. All MCB & RCCB/ELCB shall be of minimum 10 KA rupturing capacity. RCCB /ELCB shall have sensitivity of 100 MA. (7 Segment). INCOMER : 63A, 4P, MCB - 1 NO., OUTGOING ; 63A , 2P, ELCB/ RCCB - 3 NOS ; 6/10A SP MCB - 18 NOS

Supply, installation, testing and commissioning of UPS system comprising of 1 no 5 kVA units with a battery backup of 30 minutes duration for full load and with all standards fittings, accessories, protection, instruments, indications and controls including but not restricted to transformer, rectifier, inverter, SMF battery with float cum boost battery charger, static bypass switch, maintenance bypass, output isolation transformer, interconnections etc. including warranty and free all inclusive comprehensive maintenance services for one year after the date of handing over complete as per specifications and as required. Transformerless design shall not be accepted

Supply & installation of cubical type switchboard (UPS Panel), totally enclosed, dust & vermin proof, wall mounted fabricated out of 14 G mild steel sheets & specification as mentioned at clause 9.1, section IV along with powder coated painting, complete with following major components / switchgears, cable alleys, 100A DP CU bus bars & inter - connections & rubber mat. Incoming & outgoing cables will have BOTTOM/TOP ENTRY. As per specification, Approved makes & SLD. Panel having Incoming and Outgoing ratings as: INCOMER :1 No. 63A, DP MCB, 10kA with on indication lamp, Digital Ammeter & CT, Digital Voltmeter. OUTGOING FEEDERS: 40A, DP MCB- 2 Nos, 40A DP MCB-2 Nos. (Spare)

Supply, Installation, Testing & Commissioning of 20 KVA, Online, UPS system having 3 Phase Input and 1-Phase Output with 30 Min. battery backup complete with all accessories such as Batteries with stand/ Storage rack, Interconnecting Cables between Battery and UPS, Standard Electrical Metering and Protection Systems as per the detailed specification attached. Cost of battery and its storage rack shall be included in UPS Item Cost.

Supply, installation, testing and commissioning of 1 X 10 KVA

Supplying and fixing of 63 A, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing of 63 A, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Providing and constructing honeycomb brick masonry work in any shape and for all works with approved quality bricks having minimum crushing strength 40 Kg./Sq.cm in machine mixed Cement Mortar (CM) 1: 4 (1 part cement and 4 part coarse sand) of specified thickness as per details at all levels including racking of joints, scaffolding, curing etc complete as directed at all levels below and above highest plinth level. (Refer Item no. 3.05 of Section IV for detailed specifications)

Providing & constructing random rubble masonry un-coursed in any shape and for all works, of granite or approved quality quarry dressed stones in machine mix cement mortar 1:6 (1 part of cement:6 part of coarse sand) including levelling up the masonry work with cement concrete 1:2:4 at plinth level, racking of joints, scaffolding, curing etc., complete as directed in foundation at all levels below and up to highest plinth level. (Refer Item no. 3.10 of Section IV for detailed specifications)

Providing & constructing random rubble masonry un-coursed in any shape and for all works, of granite or approved quality quarry dressed stones in machine mixed cement mortar 1:6 (1 part of cement:6 part of coarse sand) including levelling up the masonry work with cement concrete 1:2:4 at window sills, lintel level, ceiling level and the like, racking of joints, scaffolding, curing etc., complete as directed in super structure at all heights above highest plinth level. (Refer Item no. 3.11 of Section IV for detailed specifications)

Providing and filling approved local sand free from debris,pebbles etc in trenches, plinth, under sub base surrounding areas including screening, watering and consolidation, transportation, loading, unloading, spreading etc. complete as directed. (Refer Item no. 1.10 for detailed specifications in Section IV ) Note: This item includes to bring required level camber/slope followed by consolidation for road and building works. The thickness shall be as per drawing/as instructed by Site Engineer.

Providing and laying in a compact manner 150 mm thick metal soling in plinth in two layers using average 60 to 80 mm size stones simillar to which used for concrete and RCC works, including test of materials, filling in the voids with largest possible simillar stones, covering and levelling the surface with sand/ layer of murum, dry compaction followed by watering, topping up with sand / murram and consolidation with mechanical plate compactor etc. all complete as directed.(Refer Item no. 1.11 for detailed specifications in Section IV ) Note: This item includes to bring required level camber/slope followed by consolidation for road and building works. The thickness shall be as per drawing.

Providing and laying dry stone pitching up to 300 mm thick to earthen embankment using stone blocks of approved size, hard, durable and fairly regular in shape and its thickness in any one direction shall not be less than the thickness of pitching as specified and laid to the required slope and filling the joints with cement sand mortar 1:6 (1 part cement, 6 part sand) including pointing with C:M 1:4 (1 part cement, 4 part sand) etc. complete as directed.(Refer Item no. 1.14 for detailed specifications in Section IV )

Providing & filling dry brick bats with half bricks or average 40 to 65 mm thickness in required uniform size or graded, at any depth in layers, leveling, grading etc. all complete as per specification or as directed. (80% of the filled up volume will be paid for payment and 20% will be deducted for voids) (Refer Item no. 1.15 for detailed specifications in Section IV )

Carting away the excavated surplus earth / debris /rock /rock stuff etc. out side of the site including loading at site, transportation, unloading, spreading etc complete as directed. Lead shall be goverend as per the locations of the disposal sites out side the site premises and as per the local laws of the governing authorities in the area.(Refer Item no. 1.17 for detailed specifications in Section IV )

Supplying the chemicals & carrying out pre-construction Anti-termite treatment (IS 6131 part 2) with chlorpyriphos 20 EC with 1 % concentration (IS 8944) OR Imidacloprid 30.50SC with 0.075% concentration (IS 15443) at the various stages of construction in stages and as recommended by the chemical manufacturer to safeguard the building against termite including execution and submission of guarantee for a period of 10 years against any subterranean pests infestation. This work is to be got executed through an approved specialized agency as per their specifications. (Measurement shall be as per out to out plan dimension in SqM at plinth level of the building treated). Stages of treatment:- A). Treatment for RCC foundations and basement :- After the backfilling up to GL, the peripheral walls shall be treated at its both side up to 500mm depth at the rate of 7.5 Ltr/SqM. B). Treatment at the junction of the wall and floor (filling). :- After the plinth filling is completed, both the sides of the walls at the junction of the wall and filling to be treated at the rate of 7.5 Ltr/SqM. C). Floor treatment :- The top surface of the consolidated earth within plinth walls shall be treated with Chemical emulsion at the rate of 5 Ltr / SqM. D). Treatment of soil along the perimeter of building. :- After the building is complete, the earth along the external perimeter of the building shall be treated for a depth of minimum 300mm & width upto 750mm with Chemical emulsion at the rate of 7.5 Ltr/SqM. E). Treatment of Soil surrounding Pipes, Wastes and Conduits and any other service line going inside the building. (Refer Item no. 1.18 for detailed specifications in Section IV )

Clearing jungle including up-rooting of rank vegetations, thorny bushes, saplings, trees of girth (circumference) up to 300mm measured at a height of 1 metre above ground level, other vegetation cover, jungle plants, shrubs, climbers etc all in order to get the clear land having its original top layer including stacking all the removed debris, rubbish, vegetation, trees, saplings etc at the place as directed anywhere within site including loading, unloading, applying all machineries and equipments, etc all complete as directed. (Refer Item no. 1.19 for detailed specifications in Section IV )

Providing and laying / spreading in close packing, levelling approved quality stone aggregate simillar to which used for concrete and RCC works having average size 40 - 50 mm and of thickness as specified in approved drawings or as directed. (Item Self Explainatory - no detailed specifications in Section IV)

Excavation in soil/terrain/land at the project site which includes all kinds of soils or rock or soils and rock which can be excavated by Manually or by Mechanical excavators or by heating or by any other approved method or by all of these methods or by any combination of these methods and up to 1.50 M depth from Existing Ground Level(GL/EGL/NGL) or the terracing level formed by massive cutting whichever is lower, for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits, underground sumps, ETP tanks, septic tank, soak well, manhole chamber, gully chamber, Utility chamber, inspection chamber, catch pit chamber, equipment foundation, machinery foundation, box cutting for formation of road, including all lift, shoring, strutting, bailing out water/pumping off water if required, re-filling the trenches, foundation pits etc all as excavated, ramming, watering, consolidating in 30 cms to 40 cms layers as directed, the item also includes all the lift and all the lead for handling and re-handling of all the earthwork operations involved for removing and stacking the excavated stuff any where within the site area or at the nearby other plot/location; simultaneously or intermittently or as and when required, including bringing back the excavated stuff as and when required for re-filling or plinth filling, for land development, back-filling etc at the project site including all the operations of levelling and consolidation etc complete as directed. The excavated surplus earth stuff at the project site and at the nearby other plot shall be levelled as directed. (Refer Item no. 1.01 for detailed specifications in Section IV). In the case of excavation required in the filling areas at a later stage and as directed, the same shall be measured from the level of filling carried out already, if any for the consideration of depth (lift). This item shall not be applicable for massive cutting-filling works for land terracing which shall be paid under relevant item provided separately under this contract. For excavation in trenches for laying of pipes and cables (and all the services), excavation and all related earthwork are included under the respective items of pipes and cables etc services even if it is not specified under the respective item. Bidder must visit the project site and arrange to evaluate about the type of soil/terrain/land exist there and the actual lead distance between the project site and the nearby plot/location of the Service Note: Filling in the buildings/ road/ land development etc with compaction/ consolidation within site is included in the item & shall not be paid seperately.

Excavation in soil/terrain/land at the project site which includes all kinds of soils or rock or soils and rock which can be excavated by Manually or by Mechanical excavators or by heating or by any other approved method or by all of these methods or by any combination of these methods and from 1.5 M to 3.0 M depth from Existing Ground Level(GL/EGL/NGL) or the terracing level formed by massive cutting whichever is lower, for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits, underground sumps, ETP tanks, septic tank, soak well, manhole chamber, gully chamber, Utility chamber, inspection chamber, catch pit chamber, equipment foundation, machinery foundation, box cutting for formation of road, including all lift, shoring, strutting, bailing out water/pumping off water if required, re-filling the trenches, foundation pits etc all as excavated, ramming, watering, consolidating in 30 cms to 40 cms layers as directed, the item also includes all the lift and all the lead for handling and re-handling of all the earthwork operations involved for removing and stacking the excavated stuff any where within the site area or at the nearby other plot/location; simultaneously or intermittently or as and when required, including bringing back the excavated stuff as and when required for re-filling or plinth filling, for land development, back-filling etc at the project site including all the operations of levelling and consolidation etc complete as directed. The excavated surplus earth stuff at the project site and at the nearby other plot shall be levelled as directed. (Refer Item no. 1.02 for detailed specifications in Section IV). In the case of excavation required in the filling areas at a later stage and as directed, the same shall be measured from the level of filling carried out already, if any for the consideration of depth (lift). This item shall not be applicable for massive cutting-filling works for land terracing which shall be paid under relevant item provided separately under this contract. For excavation in trenches for laying of pipes and cables (and all the services), excavation and all related earthwork are included under the respective items of pipes and cables etc services even if it is not specified under the respective item. Bidder must visit the project site and arrange to evaluate about the type of soil/terrain/land exist there and the actual lead distance between the project site and the nearby plot/location of the S Note: Filling in the buildings/ road/ land development etc with compaction/ consolidation within site is included in the item & shall not be paid seperately.

Excavation in soil/terrain/land at the project site which includes all kinds of soils or rock or soils and rock which can be excavated by Manually or by Mechanical excavators or by heating or by any other approved method or by all of these methods or by any combination of these methods and from 3.0 M to 4.5 M depth from Existing Ground Level(GL/EGL/NGL) or the terracing level formed by massive cutting whichever is lower, for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits, underground sumps, ETP tanks, septic tank, soak well, manhole chamber, gully chamber, Utility chamber, inspection chamber, catch pit chamber, equipment foundation, machinery foundation, box cutting for formation of road, including all lift, shoring, strutting, bailing out water/pumping off water if required, re-filling the trenches, foundation pits etc all as excavated, ramming, watering, consolidating in 30 cms to 40 cms layers as directed, the item also includes all the lift and all the lead for handling and re-handling of all the earthwork operations involved for removing and stacking the excavated stuff any where within the site area or at the nearby other plot/location; simultaneously or intermittently or as and when required, including bringing back the excavated stuff as and when required for re-filling or plinth filling, for land development, back-filling etc at the project site including all the operations of levelling and consolidation etc complete as directed. The excavated surplus earth stuff at the project site and at the nearby other plot shall be levelled as directed. (Refer Item no. 1.03 for detailed specifications in Section IV). In the case of excavation required in the filling areas at a later stage and as directed, the same shall be measured from the level of filling carried out already, if any for the consideration of depth (lift). This item shall not be applicable for massive cutting-filling works for land terracing which shall be paid under relevant item provided separately under this contract. For excavation in trenches for laying of pipes and cables (and all the services), excavation and all related earthwork are included under the respective items of pipes and cables etc services even if it is not specified under the respective item. Bidder must visit the project site and arrange to evaluate about the type of soil/terrain/land exist there and the actual lead distance between the project site and the nearby plot/location of the S Note: Filling in the buildings/ road/ land development etc with compaction/ consolidation within site is included in the item & shall not be paid seperately.

Excavation in soil/terrain/land at the project site which includes all kinds of soils or rock or soils and rock which can be excavated by Manually or by Mechanical excavators or by heating or by any other approved method or by all of these methods or by any combination of these methods and from 4.5 M to 6.0 M depth from Existing Ground Level(GL/EGL/NGL) or the terracing level formed by massive cutting whichever is lower, for foundations of wall, columns, plinth beams, basement, raft, ducts, trenches, pits, underground sumps, ETP tanks, septic tank, soak well, manhole chamber, gully chamber, Utility chamber, inspection chamber, catch pit chamber, equipment foundation, machinery foundation, box cutting for formation of road, including all lift, shoring, strutting, bailing out water/pumping off water if required, re-filling the trenches, foundation pits etc all as excavated, ramming, watering, consolidating in 30 cms to 40 cms layers as directed, the item also includes all the lift and all the lead for handling and re-handling of all the earthwork operations involved for removing and stacking the excavated stuff any where within the site area or at the nearby other plot/location; simultaneously or intermittently or as and when required, including bringing back the excavated stuff as and when required for re-filling or plinth filling, for land development, back-filling etc at the project site including all the operations of levelling and consolidation etc complete as directed. The excavated surplus earth stuff at the project site and at the nearby other plot shall be levelled as directed. (Refer Item no. 1.04 for detailed specifications in Section IV). In the case of excavation required in the filling areas at a later stage and as directed, the same shall be measured from the level of filling carried out already, if any for the consideration of depth (lift). This item shall not be applicable for massive cutting-filling works for land terracing which shall be paid under relevant item provided separately under this contract. For excavation in trenches for laying of pipes and cables (and all the services), excavation and all related earthwork are included under the respective items of pipes and cables etc services even if it is not specified under the respective item. Bidder must visit the project site and arrange to evaluate about the type of soil/terrain/land exist there and the actual lead distance between the project site and the nearby plot/location of the S Note: Filling in the buildings/ road/ land development etc with compaction/ consolidation within site is included in the item & shall not be paid seperately.

Total Bid Amount (Incl. GST) (INR)

Please Enable Macros to View BoQ information