Maintenance and Repairs to Community Hall near Raja Lodge at w.n.21

Amount

Dismantling the existing damaged plain cement concrete flooring including removel of deprices from site etc., complete as diercted by the dept officers.

Earth work excavation for levelling in all kinds of soils and sub soils to full depth as directed by the departmental officers except hard rock inclusive of shoring strutting and balling out water wherever necessary and refilling the sides of foundation with excavated earth in layers of 15cm thick well rammed and consolidated and depositing the surplus earth with in the compound in places shown by the departmental officers with initial lead of 10 meters and initial lift of 2 meters including cost of all labour charges etc., complete as per standard specification 23 & 24 VI (S2) VII.9,10

Plain Cement concrete 1 : 4 : 8 (one cement, four sand and eight aggregates) using 40mm ISS HBG metal including cost and conveyance of all materials and labour charges for mixing, laying, compacting and curing etc, complete as per SS

Plain Cement concrete 1 : 2 : 4 (one cement, two sand and four aggregates) using 20mm ISS HBG metal including cost and conveyance of all materials and labour charges for mixing, laying, compacting and curing etc, complete as per SS

Brick work In CM 1:5 mix using best country bricks of size 8 3/4 x 4 1/4 x 2 3/4' having 350kg/cm2 compressive strength and 15% or less water absorbentin the period of 24hours immersement and confirming to ISI specifications.and using the screened sand and all the materials should be approved by the competent technical authorities etc complete complying with standard specification--10m3

Plastering in cement mortar 1:3 mix 12mm thick using clean screened sand and including cost of curing for fifteen days from the completion of the work and surface should free from undulations and including the cost of preparing the surface for plastering and protecting for plastering for plastering and protecting from other damages till setting of mortar etc.complete complying with standard specification--10m2

76.) Steel Door : Manufacturing and supplying and fixing of steel doors with the following specifications. MS angles of size 40x 40x 6mm at 3.5 Kg./m are used for the outer frame and MS angle of size 35x 35x 5mm at 2.6 Kg/m for the shutter frames. Stiffeners with 32x6mm at 1.5 Kg./m MS flat is provided as the lockroll of the door and welded intact of both ends to the shutter frame 18g CR sheets of best quality is laid as panel in the shutter frames 18x5mm at 0.7 Kg./m MS flat is welded over the 32x6mm at 1.50 Kg./m MS flat on the rear side of the door sandwitching the CR sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg./m MB flats are provided diagonally onthe rear side of the shutter 2 Nos. of hinges in case of single leaf and 4 nos. of hinges in case of double leaf shutters is provided. 6 Nos. of hold fasts 120mm length spilced at the ends are wolded to the outer frame of the door. Tower bolt 2 Nos. one at the top and the other at the bottom are provided.

Ceramic tile Floor 305 mm x 305 mm x 10mm 50 Paving the floor with palin/design (desin should be got approved by the departmental officers before purchase) ceramic tiles (colour and shade as directed) of size 305 mm x 305mm x 6 mm in all floors over a base layer of cement mortar 1:3 (one cement and three sand ) 20mm thick laid in-situ and pointed with same coloured cement etc completecomplying with standard specification

63.a). Painting external wall with two coats of best approved quality of Plastice Emultion Paint over a including One Coat of priming of Exterior Emulsion Paint - Water Based Primer (Liquid) primier over cement surface wall as dirceted by the departmental officers including cleaning preparing the surface etc,complete complying with standard specification.The cement paint should be got approved by the departmental officers before use on work

Paintinting two coats for New iron work surface using best quality synthetic enamel paint etc complete complying with standard specification - 10m2

58,a) Painting With Red Oxide Primer for new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved red oxide paint over Iron Surface in all floors including cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

supply and fixing of SINTEX TANK OF 1000 LIT CAPACITY etc completed as per std

Supply and fixing of 15 mm G.I PIPE etc., complete

Supply and fixing of 15mm G.I Specials etc., complete TAP

15 MM ELBOW

15 MM PIPE NIPPLE

ravikumar muralikumar