SPL REPAIR OF BLDG NO T 43 AND OTHER ALLIED WORKS AT CHABUA LOC UNDER GE DINJAN

Amount

Dismantling asbestos cement sheet, ridge (corrugated, semicorrugated, plain etc.) in roof covering,wall etc or of similar types complete all as specified and directed.

Dismantling of timber scantlings 40 sqcm & over in section framed work complete all as specified and directed.

Dismantling of timber scantlings 40 sqcm & over in section unframed work complete all as specified and directed.

Taking down chowkhats or frames with shutters without taking off shutters from the frames not exceeding 1.5 Sqm each complete all as specified and directed.

Taking down chowkhats or frames with shutters without taking off shutters from the frames exceeding 1.5 Sqm & not exceeding 4.0Sqm each complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors of any description (below or above ground level) complete all as specified and directed.

Dismantalling of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete in all respect as specified and directed.

Taking down cement plaster of any thickness and description on brick/concrete/stone walls, ceilings, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Taking down plastering on lathing (other than wire-netting), without removing lathing, in cement mortar (one side only measured in cases where both sides are plastered complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Demolition of brickwork or stone/ boulder masonry, built in cement mortar complete all as specified and directed.

Dismantling wooden weather boarding of any description fixed in any position with nails/ screws complete all as specified and directed.

Dismantling of floor/ wall tiles including cement mortar bedding of any thickness upto PCC/ RCC/brick surface and rubbish off the premises, complete in all respect all as specified and directed.

Taking down shutter exc 1 sqm and n. exc 2 sqm each, complete in all respect as specified and directed.

Demolition and breaking up drain pipes 75 mm/110 mm bore dia (Salt glazed ware, PVC or Reinforced concrete) set in cement mortar, complete in all respect as specified and directed.

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering / wall cladding fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

M&L for hot dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550MPa as in ridge / valley / gutters fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

M&L for hot dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550MPa as in eaves board or of similar type fixed with self tapping screws alongwith bitumen washer fixed over mild steel flats, angles etc fixed with framed structure complete all as specified and directed. including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

S&F Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, tubular/hollow section, channel or flat sections) including distance pieces, cleats etc. using Fe-410W (Grade E-250 quality "A") including necessary welding complete complete all as specified and directed.

M&L in repair for second class HW scantalling, wrought, in any position for framed work , jointing with necessary nails, nut bolts etc including necessary supports for truss structure complete all as specified and directed.

S&F second class HW plain,solid,straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F rolled section as in framing for door/vent/CB/chowkhats, water staging,wind tie and the like using angle, tee, hollow tubes etc., cleat and connecting plates complete (Butt hinges shall be measured and paid for separately) using Fe 410-W (Gde-E-250) quality "A" complete all as specified and directed.

S&F mild steel work such as in guard bars, grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; and of similar type of work conforming to Fe 290, Gde-E-165 complete all as specified and directed.

S&F mild steel screw bolts 11 to 15mm diameter of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and haxagonal or square exe 5 cm and n exc 10 cm long complete in all respect as specified and directed.

S&F 30mm thick second class HW glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc,sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) complete all as specified and directed.

S&F 30mm thick glazed and skeleton (30mm thick in 2nd class hardwood) without sash bars for window,ventilators as per SSR Part I , section 8 clause 8.24(b) complete all as specified and directed.

S&F 30mm thick glazed and skeleton(30mm thick in 2nd class) hardwood with sash bars for window,ventilators as per SSR Part I , section 8 clause 8.24(b) complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixing with beads in door/window/ventilator/fixed glazing shutters complete all as specified and directed.

S&F 75mm size stainless steel butt hinge(ISI marked) complete all as specified and directed.

S&F 100 mm size of mild steel butt hinges ISI marked, complete in all respect as specified and directed.

S&F 200mm length of bolt, Aluminium anodised, barrel tower bolt of extruded section complete all as specified and directed.

S&F 150 mm size, Aluminium handle cast type anodised complete all as specified and directed.

S&F 30mm thick flush shutter, solid core construction, with block board core with decorative face veneers with lipping on both sides complete all as specified and directed.

M&L for preparation of new undecorated wooden surfaces with pre mixed wood filler used as putty of grith exc 10cm and applying two coats of synthetic enamel paint over one coat of pink primer before painting complete all as specified and directed.

M&L for preparation of old decorated wooden surfaces with pre mixed wood filler used as putty of grith exc 10cm and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of new undecorated steel surfaces with pre mixed steel filler used as putty for steel work and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer before painting complete all as specified and directed.

M&L for preparation of old undecorated steel surfaces with pre mixed steel filler used as putty and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old decorated plastered surface of wall after complete removal of existing treatment and applying two coats of weather coat over 2 mm thick wall care putty (in two layers) over a coat of primer including preparation of surface, complete in all respect as specified and directed.

M&L for preparation of newly plastered surface of wall and applying two coats of weather coat over 2 mm thick wall care putty over a coat of primer including necessary preparation of surface, complete in all respect as specified and directed.

M&L for preparation of new surface of plastered wall using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller over including one coat of alkali resistant priming paint before distempering complete all as specified and directed.

M&L for preparation of old decorated surfaces including washing, rubbing down and stopping of white wash surfaces of walls (Plastered or un-plastered) including cormices pilasters etc and using wall care putty to fill the voids and applying two coats of oil bound distemper and finished another one coat with spunge roller including one coat of alkali resistant priming paint before distempering complete all as specified and directed.

S&F for solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, supplying & fixing in opening as per specification & drawing, complete in all respect as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel haivng a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and botom rail on either side & as gap insert for top rail & bottom rails; Panelling of plain colour PVC sheet to be fitted in the M.S. frame weloded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling and fixing in the frame at site as per specification & drawing, complete in all respcet as specified and directed.

M&L for half brick work with sub-class "B", old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:4) including dismantaling of brick work built in cement mortar in any position complete in all respect as specified and directed.

M & L brick work with sub-class "B", old size bricks of class designation 75, straight or curved on plan exc. 6m mean radius built in CM (1:6) including dismataling of brick work built in cement mortar in any position complete in all respect as specified and directed.

M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:4) finished even and smooth without using extra cement complete in all respect as specifified and directed.

M & L 15mm thick plastering on brick/stone/concrete surafces of wall in cement mortar (1:6) finished even and smooth without using extra cement complete in all respect as specifified and directed.

M & L 15mm thick plastering on wall in cement mortar (1:4) finished even and smooth without using extra cement on one side of lathing or stone masonary surface other than fair face complete in all respect as specifified and directed.

M & L 15mm thick plastering on wall in cement mortar (1:6) finished even and smooth without using extra cement on other side of lathing or stone masonary surface other than fair face on other side of lathing complete in all respect as specifified and directed.

M & L GI wire netting 0.90mm dia and 12mm mesh lathing to wood or metal studding, joists, etc. in walls, ceilings, stanchions, beams, etc. including all laps, cutting and waste complete in all respect as specifified and directed.

Supply only water proofing compound complete, in all respect as specified and directed.

Forming Contration (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound of grade 'B' complete in all respect as specifified and directed.

Providing and laying cement concrete in coping, hold fasts, using type B-1, 1:2:4 (using 20mm nominal size crushed and graded stone aggregate) or of similar work, etc. including necessary form work etc. complete in all respect as specifified and directed.

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 1000 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed.

S&F three layered white in colour rotational moulded made out from LLDPE material water storage tanks of capacity 500 ltr (cylindrical vertical with closed top) including three tank nipples of 20 mm nominal bore dia hoisted and fixed in position including dismantling/ taking down all as specified in SSR part I, complete in all respect as specified and directed.

S & F 4mm thick frosted glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete in all respect as specifified and directed.

S & F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete in all respect as specifified and directed.

S & F plain fillets. square, rectangular or triangular in section, clean sawn, secured with nails or brads using second class wrought HW sec area exc 13 Sqcm but not exc 25 Sqcm including taking down of framed work complete in all respect as specifified and directed.

S&F exposed GI powder coated snap grid frame work for false ceiling in flat or in sloping , of grid size 600x600mm comprising of wall/cleat angle of size 25x25x0.35mm and cross tee of size 24x38x0.70mm with 2mm dia GI wire as suspender and including 3.5-4mm thick decorative, pre -painted, non asbestos board (E-Board) in false ceiling including fixing arrangement from steel/wooden truss of any type including dismantaling of existing false ceiling complete in all respect as specified and directed.

Providing and laying non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 Sqm in floors etc., set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick screed bed in cement mortar (1:4) complete in all respect as specifified and directed.

Providing and laying glazed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

Providing and laying non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick screed bed in cement mortar (CM) 1:4, complete in all respect as specified and directed.

Providing and laying non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in skrting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match tile colour over 15 mm thick rendering in cement mortar (CM) 1:4, complete in all respect as specified and directed.

Supply and fixed for light Shade polished vitrified floor tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 15mm thick screed bedding in cement sand mortar (1:4) complete in all respect as specified and directed.

Supply and fixed for light shade polished vitrified floor tiles 10mm thick (square/rectangular) area of each tile exceeding 0.36 sqm but not exceeding 0.42 Sqm, in skirting set and jointed in neat cement slurry and pointed in white cement with pigment to match the tile colour over 10 mm thick rendering in cement mortar (CM) 1:4 complete in all respect as specified and directed.

Roughening of surfaces of old concrete floor by picking, sweeping clean, and washing down with water to remove dust, etc. complete all as specified & directed.

M&L for Brushing neat cement slurry with 3.00 Kg of cement per sqm complete all as specified & directed.

Providing and laying plinth protection of 75mm thick cement concrete, using type C-1, (1:3:6) (using 20mm nominal size crushed and graded stone aggregate), laid in alternate penals/bays and finished the surafce even and smooth without using extra cement complete in all respect as specifified and directed.

Taking down of existing roof treatment from roof and terrance, roughening surface of old concrete roof by picking, sweeping clean and washing down with water to remove dust, etc and applying roof treatment with the following specification :- (a) Applying cement slurry over concrete surfaces @3kg/sqm. (b) Rendring 15mm thick in cement mortar (1:4) mixed with water proffing compound as per manufactures instruction on cleaned concrete surfaces of roof and finishing the surfaces fair and even including curing the plastered surfaces for 7 days by ponding of water over the roof, (leveling course). (c) Applying evenly one coat of cold bituminous primer conforming to [email protected] liter per square metre on the cleaned plastered surfaces (d) Applying evernly one coat of blown hot bitumen of grade 85/25@ 1.20 Kg per square metre on primed surfaces. (e) Applying a layer of APP based polymeric membrane, 3mm thick (minimum) weighing 3.50 Kg per square metre reinforces) with polyster non woven fabric wighing not less than 160 gms per square metre by torch application. The overlap shall be not less than 100mm on transverese direction and 75mm on longitudinal direction and sealing overlsaps. (f) Applying evenly one coat of aluminium paint @ 0.10 litre per square metre over the APP based polymeric membrane.

M&L for any colour of granite stone without white spots Granite stone slab 20 mm thick, as in floor, dado, steps, laid over and including screed bed 15 mm thick in cement mortar (CM) 1:6, jointed and pointed with white cement mixed with pigment to match the shade of stone including cuttingl rubbing and polishing surface, including cutting for wash hand basin, sink, gas pipe hole etc., to the entire satisfaction of the Engineer-in-Charge, complete in all respect as specified and directed.

M&L 10 mm thick plastering on brick/ stone/ concrete surfaces of ceiling in cement mortar (1:3) finished even and smooth without using extra cement, complete in all respect as specified and directed.

Supply & Laying 25mm OD CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall complete all as specified and directed.

Supply & Laying 20mm OD CPVC pipes SDR 11 and plain CPVC SDR-11 fittings on walls/ceiling or laying in floors/concealed in wall complete all as specified and directed.

S&F in repair 20 mm bore of Gun-metal, globe or gate valve, with iron wheel head, screwed both ends for iron pipe and fixed, complete in all respect as specified and directed.

S & F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. or for window grill of appd size and shapeincluding fixing with aluminium "U" shape section for fixing etc. complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium three tier window frame including necessary joining cleats, of Jindal section No 20832 or equivalent section of approved make of 1.5mm thick complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium window and ventilator shutters, side hung type with/without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No) grade), powder coated aluminium snap beading, screws, powder coated aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21, 100mm long (2 no.) suitable handle (1 no.) complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S & F powder coated aluminium sliding window with/without sash bars, aluminium sections of thickness 2mm including necessary joining cleats, glazing clips, EPDM rubber packing (of 50 No grade), powder coated aluminium snap beading, screws, center grooved stainless steel ball-bearing double roller 2 position height adjustment, sound/dust brush, recessed handle with locking arrangement complete in all respect as specified and directed. (Powder coating shall be min 50micron) (Note: all external members to be joined at 45 degree angle at corner)

S&F in repair mild steel 300 mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

S&F in repair PVC coloured insulated over MS pipe 20 mm dia curtain rod with fixing bracket, stops, rollers etc. complete all as specified and directed.

S&F sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to drarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm, complete in all respect as specified and directed.

S&F in repair PTMT ball valve high pressure 20 mm bore with epoxy coated aluminium rod & high-density plastic ball screwed for iron pipe, complete in all respect as specified and directed.

S & F in repair vitreous china wash down water closet Pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device (exclusive flushing cistern and flush pipe) complete all as specified and directed.

S&F in repair PVC valveless, syphonic action type, low level dual flush cistern 10 ltr capacity, white, wtih inlet, ball valve, float and handle including brackets & flush pipe of polyethylene for low or high level cistern of required height of high density PVC, 32 mm dia pipe, complete in all respect as specified and directed.

S&F PVC connection 15 mm size with PTMT nuts of length 450 mm, complete in all respect as specified and directed.

S&F in repairs 15 mm bore fancy type CP finished angle valves, cast copper alloy, screwed down, high pre-ssure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions, complete in all respect as specified and directed.

S&F in repairs long body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F in repairs short body Bib taps of 15 mm bore, fancy type CP finish cast copper alloy with crutch handle, screwed down, screwed for iron pipes, complete in all respect as specified and directed.

S&F Tubular towel rail, 20 mm dia, D type, 60 cm long between flanges cast copper alloy, chromium plated finish, complete in all respect as specified and directed.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long, complete all as specified and directed.

S & F in repair Pedestal stand with Wash hand basins, vitreous China of size 550 x400mmX800mm(flat back or angle back type), including cutting for and pinning in ends of brackets over new angle iron erecting stand embedded in PCC (1:2:4) block including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type brass CP Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete in all respect as specified and directed. Make Hindware, Cat Part No. 10098, 11032(WHB with pedestal), Cat Part No. F730001(Pillar Cock) Cat Part No. F860010 (Waste coupling 32mmSS) or equivalent make from approved list of makes.

S & F in countertop Wash hand basins, vitreous China of size 530 x420mmX140mm, including 32mm dia bore waste fitings cast copper alloy chromium plated with long screwed shanks and flynuts flange and beded in redlead cement, PVC waste pipe including 15mm bore dia fancy type CP finish Pillar tap, cast copper alloy with capstan heads, screwed down high presuure, with lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipes complete in all respect as specified and directed.

S & F in repair vitreous china single piece wash down water closet Pan (pedestal pattern) white including plastic water closet seat cover, white, closed pattern with flat bottom, and mild steel chromium plated hinging device inclusive flushing cistern and flush pipe complete all as specified and directed.

S&F Vitreous China urinals, full stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern complete all as specified and directed.

S&F in repair Health faucet ABS SS braided hose 1 mtr with V hook including fixing arrangement, complete in all respect as specified and directed. Make:- Hindware, Cat Part No. F160068IV), or equivalent make from approved list of makes.

S&F 75 mm dia of outlet, PVC (SWR) nahani trap, plain with SS grating of size 150mmX150mm, 0.75mm thick openable at center including jointing with solvent cement, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 75mm bore including necessary MS pipe clamp, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) pipes single sockedted in any length with rubber ring joints laying in trenches 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 110mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) single (single 'T') equal or unequal 75mm bore pipe with access door, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 110 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) bends any radius 75 mm bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 110 mm dia bore, complete in all respect as specified and directed.

S&F PVC (SWR) vent cowl 75 mm dia bore, complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 160mm outside diameter as per IS:13592-1992 including dismantling and breaking up existing drain pipes and fixing necessary mild steel pipe clamps complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) bends any radius for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) junction single, (single Tee) equal or unequal for160mm outside diameter of pipe as per IS:14735-1999 complete in all respect as specified and directed.

Supply and fixed unplasticised PVC (SWR) Gully trap 125/110 mm, setting and jointing with solvent cement complete in all respect as specified and directed.

M&L for precast RCC, type B-1, 1:2:4 (using 20 mm crushed and graded stone aggregate) as in manhole covers/ cover slabs or of similar type slab works, etc. incl necessary formwork and loading/ unloading of the same and fixed in position, complete in all respcet as specified and directed.

Providing and laying reinforced concrete slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like using 1:2:4 type B-1, (using 20 mm crushed and graded stone aggregate) complete in all respcet as specified and directed.

M & L for formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all not exceeding 20cm wide complete in all respcet as specified and directed.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete in all respcet as specified and directed.

S&F 10 mm dia and over TMT bar cut to length bent to shape required including cracking bending spiarlly for hoping for columns, hooking ends and binding with and including Mild Steel wire (annealed) not less than 0.90 mm dia or securing with clip, complete in all respect as specified and directed.

S&F of toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

S & F Liquid soap container of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats. (Minimum weight 105gms) complete in all respect as specified and directed.

S & F Door closer hydraulically regulated, designation No.3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 kg aluminium die cast body fixed in repair all as specified and as directed.

S & F for coloured rubber moulded, glazed pre coated chequered cement concrete tiles of any shape and size 20-25mm thick with grey cement with pigment,; set jointed and pointed in neat cement slurry with pigment in floors including over 15mm thick screed bed in CM 1:4 complete in all respect as specified and directed. Sample as approved by GE.

S&F of pvc wall panelling, hollow cored, 5mm thick, decorative designs with smooths surfaces, fire resistant, water and heat proof, tongue and groove edges for easy assembly with all accessories such as U cap, end cap, tee, plugs, fillets and screws etc as per manufactures instructions and fixing complete all as specified & directed.

Taking down aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as directed.

Taking down U/s Submain wiring any type with rigid steel conduit/PVC conduit/PVC Casing caping all as specified and directed.

M&L for Point wiring complete as specified with 1100 volt grade 1.5 sq.mm. (nominal area) single core PVC insulated unsheathed cable multi-stranded copper conductor drawn through and including PVC casing and capping of suitable size but not less than 20mm , with all fittings, fixed on wall/ceiling /floor suitable for housing modular pattern switches/ sockets/ regulators etc. and duly earthed with same cable as for wiring above but green in colour as continuous earthing wire complete all as specified & directed for One light /Fan /Ex Fan point controlled by one, one way switch :- Note :- (i) Modular Plates & Covers and Modular Metal Boxes/PVC Boxes will measured and paid separately under relavant items.(ii) Necessary PVC rigid junction boxes for identifying junction as required on site/directed by Engr-in-charge for point wiring work with PVC dummy plates shall deemed to be included in the quoted rate.(iii) The wiring shall be done strietly by following proper colour coding using red, yellow and blue for phase, black for neutral and green for earth leads.

Description all as per Ser item No. 124 here-in-before but One socket outlet 3 or 5 Pin, 6 Amp on same board.

Description all as per Ser item No. 124 here-in-before One socket outlet 3 or 5 Pin, 6 Amp on independent board

Description all as per Ser item No. 124 here-in-before but with 2.5 sqmm copper cable in and including PVC casing and capping complete all as specified and as directed for socket outlet 3 or 6 pin 15 Amps.

S&F modular switch 6 Amp one way 1 module 230 V AC complete all as specified and directed.

S&F modular switch 16 Amp one way 1 module 230 V AC complete all as specified and directed.

S&F modular socket outlet 6 Amp 2 module intel multi socket for all pins 230 V AC complete all as specified and directed.

S&F modular socket outlet 16 Amp 2 module and 6/16 Amp heavy duty 230 V AC complete all as specified and directed.

S&F modular ceiling fan regulator, electronic step type, 5 speed AC 230 volts, 2 module complete all as specified and directed.

S&F Modular Bell push, 6 amps 1 module 230 V AC complete all as specified and directed.

S&F 1/2 module Metal Flush Box including white cover plate with frame for fixing of modular switeches/sockets etc. complete all as specified and directed by Engineer-in-charge.

S&F 3 module Metal Flush Box including white cover plate with frame for fixing of modular switeches/sockets etc. complete all as specified and directed by Engineer-in-charge.

S&F 4 module Metal Flush Box including white cover plate with frame for fixing of modular switeches/sockets etc. complete all as specified and directed by Engineer-in-charge.

S&F 6 module Metal Flush Box including white cover plate with frame for fixing of modular switeches/sockets etc. complete all as specified and directed by Engineer-in-charge.

S&F 8 module Metal Flush Box including white cover plate with frame for fixing of modular switeches/sockets etc. complete all as specified and directed by Engineer-in-charge.

S&F ceiling rose, three terminal, PVC/polycarbonate, isolated body, ISI marked complete all as specified and as directed.

S&F call bell/ Buzzer, Ding dong AC 230 volts single pole all as specified and directed.

S&F PVC/polycarbonate angular lamp holder insulated body with back plate angle type suitable for batten fitting complete all as specified and directed

S&F LED Tube lights fitting 1 x 18/20 Watt, 220V AC batten type with with driver,holder including 20 Watt LED tube fitting fixed on wall/ceiling and connecting up complete with flexible copper conductor cable white of suitable size and making necessary connection complete all as specified and directed.

S&F LED luminaire 600 mm x 600 mm,35/36 watt, 220 V AC recessed/surface type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof/ ceiling including connecting up with driver flexible copper conductor of suitable size complete all as specified and directed.

S&F LED building security light fitting 1 x 35 Watt new generation energy saving and environmental friendly long life LED street light made up of pressure diecast aluminium housing with high power LED as lighting source and lens embedded PC cover having top opening seperate driver compartment with IP65 protection incl mounting bracket of suitable size and connection with suitable size flexible complete all as specified and directed.

Taking down and Refixing carefully old ceiling fan/Exhaust Fan complete, including hanging arrangement of fan under different roof after repair made out of heavy duty MS hook with making connection using 3 core 1 Sqmm flexible wire complete the contactor.

S&F 9W LED bulb B 22 all as specified and as directed

S&F of batten type with surface mounted LED tube light fitting with high efficiency diffuser mirror light, aluminium housing in CRCA body suitable and including 10 watt LED tube rod high efficient, AC 220-240 volts, 50 Hz and connecting with copper conductor flexible cable of size 0.50 Sqmm from ceiling rose to connector of the light including disconnecting and taking down old exisiting light fitting of any description and in any position complete all as specified and directed.

Disconnecting and taking down old existing wall fitting of any description and in any position and S&F aesthetically designed wall bracket light with glass and B22 holder including 9 Watt LED lamp & clear diffuser including connecting up with flexible copper conductor cable complete all as specified and directed.

S&F single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one number single pole MCB 20 Amps , 240 Volts complete all as specified and as directed.

Supply & fix Distribution Board factory made sheet metal enclosure double door distribution board class IP-43 IK 09 with 200 Amp rated copper bus bar 415 Volts 4 way Triple pole and neutral link, incl taking down old u/s any type, complete all as specified and as directed.

Supply and fixing TP 25 To 63 AMP, 415V 10KA 'B' curve miniature circuit breaker (MCB) complete with connection testing and commissioning complete all as specified and as directed.

S&F single pole and neutral DB wall mounting type, 240 Volts,8 Way with 200 Amps rated bus bar, double door suitable for fixing MCB's including connecting etc and taking down U/S DB ,main switch complete.

S&F MCB single pole and neutral (SP&N) 32 Amp 240 volts 10 KA 'C' series with all incoming/outgoing connections with proper size lugs including taking down old unserviceable, complete all as specified and directed.

S&F MCB single pole (SP) 6 to 32 Amp 240 Volts 10 KA 'C' series with all incoming/outgoing connection with proper size lugs complete all as specified and directed.

Taking down carefully Aluminium strip/ roof conductor of size 25 x 3 mm and refixing the same after replacing of Roof sheet complete all as specfied and as directed.

Taking down carefully Test terminal block and refixing the same after replacing of Roof sheet complete all as specfied and as directed.

Taking down carefully Ait termination Rod and refixing the same after replacing of Roof sheet complete all as specfied and as directed.

M&L for providing sub main wiring with two single core 4.00 Sqmm (nominal area) PVC Insulated FRLSH unsheathed multi stranded copper conductor cable 1100 volts grade drawing through PVC casing capping as per direction complete including 4.00 Sqmm PVC insulated unsheathed multi stranded FRLSH single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note :- (i) Three runs of single core 4.00 Sqmm multi stranded copper cable and one run of PVC casing and caping shall be measured as one run length (ii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iii) Earth wire run inside the PVC casing caping.

M&L for providing Sub main wiring with two single core 6.00 Sqmm (nominal area) PVC Insulated FRLSH unsheathed multi stranded copper conductor cable 1100 volts grade drawing through PVC Conduit as per direction complete including 6.00 Sqmm PVC insulated unsheathed multi stranded FRLSH single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note :- (i) Three runs of single core 6.00 Sqmm multi stranded copper cable and one run of PVC casing capping shall be measured as one run length (ii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iii) Earth wire run inside the casing capping.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 3.5 core, complete.

Excavation in trenches not exc. 1.5 meter deep and not exc 1.5 metre wide for taking up/laying of under ground cable/pole and stay foundation and getting out in soft/loose soil complete as specfied and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specfied and as directed.

Removing surplus soil to a distance not exc 50 meter and depositing where directed at a level not exc 1.5 meter above the starting point complete all as specified and as directed.

M&L for brick protection over cables inside the trench by using common burnt clay building bricks,sub-class"B" laid dry and flat and width wise along the axis of the trench complete all as specified and as directed by Engineer-in-Charge.

M&L for sand cushioning in cable trenches over & under the cables, with river washed coarse sand, as per standard practice with proper compaction complet all as specified and directed by Engr-in-Charge. (Punned thickness shall be considered for payment).

S&F in repaires 40 mm bore light grade steel tubes galvanized pipe ISI marked with all fitting ISI marked, laid in trenches, under road or fixing on wall/pole/ crossing nallah etc complete all as specified and as directed .

M&L Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4mm dia (main earthing lead) by means of galvanized bolts, nuts and washers all as shown in electrical plate No 3 of MES Schedule part I (2009) with connected to earth test point to main switch board with & including adequate quantity of charocoal dust and common salt alround earth plate & 15mm dia GI Pipe light grade for earth lead protection and GI pipe 20mm dia medium grade of suitable length for watering pipe with funnel & wire mesh including necessary earth work and PCC (1:3:6) type C-1 for earth pit and 40mm thick pre-cast RCC cover in 1:2:4 type B1 with 3 Nos 8mm dia TMT bars both ways complete all as specified and directed.

M/s Dhani Enterprise (BID ID -3412665)

BHABANANDA DOLEY (BID ID -3405171)

M/s Dhruv Enterprises (BID ID -3412827)

M/s Singh enterprises (BID ID -3409780)

RS COOLING APPLIANCES (BID ID -3411434)

M/S R G Construction (BID ID -3405867)

ms singh construction (BID ID -3410687)

Shiva Soltronics Private Limited (BID ID -3410431)

BAJAJ CONSTRUCTION (BID ID -3412065)

M/S S J CONSTRUCTION (BID ID -3412076)