MMNPPNA_24_25_11 (i) Construction of Surath Nagar Adult Education office app Road ( CH 0.00m to Ch 170.00m),(ii) Construction of Topodisa Sarkaribagan Road ( CH 0.00m to Ch 1000.00m),(iii) Construction of Upper Topodisa Road(Club area) ( CH 1000.00m

Amount

(i) Construction of Surat Nagar Adult Education Office app. road (Ch.0.00m to Ch. 170.00m) Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412

Cement concrete pavement Construction of un reinforced, dowel jointed at expansion and construction joint only,plain cement concrete pavement, thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M30 grade ,coarse and fine aggregrette conforming to is:383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges,steel plates including levelling the formwork as per drawing) spreading the concrete with shovels,rakes,compacted using needle,screed and plate vibrator and finished in continuous operation including provision of contraction and expansion,construction joints,applying debonding strips,primer,sealant,dowelbars,near approaches to bridge/culverts and construction joints,admixture as approved,curingof concrete slabs for 14 days.

Excavation for structures (Earthwork in excavation for foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom, backfilling the excavated earth to the extend required and utilising theremaining earth locally for road work.) (ii). Ordinary rock (not required blasting) A. Manual means (Depth up to 3.00m)(With dewatering)

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 (A) With crushed Stone (I) P.C.C grade M 10

Reinforcement in foundation: Supplying, fitting and placing TMT (Fe-500 D) reinforcement bar (From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL) in foundation complete as per drawings and technical specifications Clauses 1000 and 1202 10 mm dia DRAIN Main Bar Outside U = 67x2.80x0.617= 115.749 kg Inside U = 67x2.50x0.617 = 103.347 kg Distribution bar Raft = 12x10.00x0.617 = 74.040 kg Wall Outside U = 2x5x10.00x0.617 = 61.700 kg Inside U = 2x5 x10.00 x 0.617 = 61.700 kg DRAIN COVER Slab Top and Bottom = 2x 67 x1.100x0.89 = 131.186 kg Distribution Bar = 2x 8 x10.00 x 0.89 =142.400 kg _______________________ Total = 690.122 kg = 0.690 tonne

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specification including steel shuttering framework. (N). Without plasticiser C. (I). RCC Grade M25

Providing weep holes in Brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipe, extending through the full width of the structure with slope of 1V :20H towards drawing foce. Complete as per drawing and Technical specification.

(ii) Construction of Topodisa Sarkaribagan Road (Ch.0.00m to Ch. 1000.00m) Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead upto 1000 m as per Technical Specification Clause 303.1.

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

WBM Grading 2 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 2 as per Technical Specification Clause 405. 2(A)WBM Grading-II

WBM Grading 3 Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. 3(A)WBM Grading-III

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared dry and hungry bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 KN static roller capacity, finishan to required level and grades to followed by seal coatof either Type A or Type B or Type C as per Technical Specification clause 508. a) By manual means (ii) with S-65 grade bitumen .

Providing, laying seal coat sealing the voids in a bituminous surface laid to the specified level, grade and cross fall using Type A or Type B or Type C as per Technical Specification clause 510. a) By manual means (ii) with S-65 grade bitumen .

Construction of unlined surface drains of average cross-sectional area 0.40 sqm in soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3m and lead of 50 m (average lead 25 m) as per Technical Specification Clause 307.

(iii) Construction of Upper Topodisa Road (Club area) (Ch.1000.00m to Ch. 1300.00m) Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412

Cement concrete pavement Construction of un reinforced, dowel jointed at expansion and construction joint only,plain cement concrete pavement, thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M30 grade ,coarse and fine aggregrette conforming to is:383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges,steel plates including levelling the formwork as per drawing) spreading the concrete with shovels,rakes,compacted using needle,screed and plate vibrator and finished in continuous operation including provision of contraction and expansion,construction joints,applying debonding strips,primer,sealant,dowelbars,near approaches to bridge/culverts and construction joints,admixture as approved,curingof concrete slabs for 14 days.

Earth work in excavation for structures as per drawing and Technical specifications clause305.11ncluding setting out , construction of shoring and bracing, removal of stumps and other deleterious materails and disposal upto a lead of 50 m , dressing of sides and bottom and backfilling in trenches with excavated suitable material. 1.in ordinary soil (i)upto 3 m depth

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and technical Specifications Clause 802, 803, 1202, 1203. (A) with Crushed Stone (I) PCC grade M 10.(i) Nominal mix 1:3:6

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and technical Specifications Clause 802, 803, 1202, 1203. A) with Crushed Stone (IV) RCC grade M 20

Plain / reinforced cement concrete in substructure complete as per drawings and Technical Specification Clauses 802 ,804 ,805 ,806 ,807 ,1202 ,and 1204 (A) with Crushed Stone I.PCC grade M 15 (i) Nominal mix 1:2.5:5.

Plain / reinforced cement concrete in substructure complete as per drawings and Technical Specification Clauses 802 ,804 ,805 ,806 ,807 ,1202 ,and 1204 (A) with Crushed Stone (III).RCC grade M 20 (1:2:4) (Nominal mix) (i) For height upto 5m.

Providing and laying reinforced cement concrete in superstructure as per drawing and technical specification clauses800, 1205.4, and 1205.5 (A) with Crushed Stone (II) RCC M 25 (1:1.5:3) (A) Height upto 5m

Supplying, fitting, and placing TMT bar reinforcement (Fe 415) in foundation complete as per drawing and Technical Specifications Clauses 1002, 1005, 1010 and 1202.

Supplying, fitting, and placing MS bar reinforcement in foundation complete as per drawing and Technical Specifications Clauses 1000, and 1202.

Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and Technical Specifications Clauses 1002, 1010 and 1202.

Providing pressure Relief pipe 100 mm dia in bottom slab of Box cell on a filter media base of 500 mm x500 mm as per drawing and Technical Specifications Clauses 1205.5.7

Excavation for structure:- Earth work in excavation for structures as per drawing and Technical specifications clause305.11ncluding setting out , construction of shoring and bracing, removal of stumps and other deleterious materails and disposal upto a lead of 50 m , dressing of sides and bottom and backfilling in trenches with excavated suitable material. II. Ordinary Rock (not requirng blasting) (i)upto 3 m

Providing concrete for plain/reinforced concrete in open foundations complete as per drawing and technical Specifications Clause 802, 803, 1202, 1203. (A) with Crushed Stone (I) PCC grade M 10. (i) Nominal mix 1:3:6 (Hand mix)

Brick masonry work in cement mortar in foundation complete excluding pointing and plastering as per drawing and technical specifications Clauses 600, 1202 & 1203 I.Brick masonry in 1:3 cement mortar

Plastering with cement mortar (1:4), 15 mm thick on brickwork in substructure as per technical specification Clauses 613.4 & 1204

(iv) Construction of Digrik Guruling to Medical sub center Road (Ch.0.00m to 112.00m) Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201. (I)By Manual Means (B)In area of non thorny jungle

Earth work in Hill Road i. Excavation in soil in Hilly Area by manual means A) Excavation in soil in Hilly Area by manual means including cutting and trimming of side slops and disposing of excavated earth with a lift upto 1.5m and a lead upto 20m as per drawing and Technical Specification Clause 1603.1 (Manual means should be use machines cannot be deployed due to site condition)

Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412

Cement concrete pavement Construction of un reinforced, dowel jointed at expansion and construction joint only,plain cement concrete pavement, thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M30 grade ,coarse and fine aggregrette conforming to is:383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges,steel plates including levelling the formwork as per drawing) spreading the concrete with shovels,rakes,compacted using needle,screed and plate vibrator and finished in continuous operation including provision of contraction and expansion,construction joints,applying debonding strips,primer,sealant,dowelbars,near approaches to bridge/culverts and construction joints,admixture as approved,curingof concrete slabs for 14 days.

Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. 1. Ordinary soil (ii) Upto 3 m depth

PCC 1:3:6 in Foundation Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.

Stone masonry work in cement mortar 1:3 for substructure complete as per drawing and Technical Specifications III. Random Rubble Masonry

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106.

Plastering with cement mortar (1:3 ) on brick work in sub-structure as per Technical specifications.

(v) Construction of Link road from Upper Dibarai to H.T. Road (Ch.0.00m to 170.00m) Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412

Cement concrete pavement Construction of un reinforced, dowel jointed at expansion and construction joint only,plain cement concrete pavement, thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M30 grade ,coarse and fine aggregrette conforming to is:383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges,steel plates including levelling the formwork as per drawing) spreading the concrete with shovels,rakes,compacted using needle,screed and plate vibrator and finished in continuous operation including provision of contraction and expansion,construction joints,applying debonding strips,primer,sealant,dowelbars,near approaches to bridge/culverts and construction joints,admixture as approved,curingof concrete slabs for 14 days.

(vi) Construction of Dibarai Rotary & Dibarai Club App Road (Ch.0.00m to 91.00m) Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405. 3(A)WBM Grading-III

Providing and laying interlocking concrete block pavement (M40) having thickness 80mm as per technical specification clause 1504 complete including carriage. (a) Including Edge block/ Edge restraints

(vii) Construction of Dibarai Western Hapai Approach Road (Ch.0.00m to Ch. 173.00m) Removal of unsuitable soil including excavation, loading and disposal upto 1000 m lead but excluding compaction ground supporting embankment subgrade replacement by suitable soil, which shall be paid separately as per Clause 303.5.2 as per Technical Specification Clause 302.3.11

Laying brick soling layer on prepared sub-grade with brick on end edging according to lines, graded and cross-section shown on the drawing filling joints with sand and earth, spreading 25 mm thick layer of earth over brick soling, watering and rolliing the same with three wheel road roller 80-100 kN as per Technical Specification Clause 412

Cement concrete pavement Construction of un reinforced, dowel jointed at expansion and construction joint only,plain cement concrete pavement, thickness as per design,over a prepared sub base,with 43 grade cement or any other type as per clause 1501.2.2 M30 grade ,coarse and fine aggregrette conforming to is:383,maximum size of coarse aggregate not exceeding 25 mm,mixed in a concrete mixer of not less than 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (steel channel,laying and fixing of 125 micron thick polythene film,wedges,steel plates including levelling the formwork as per drawing) spreading the concrete with shovels,rakes,compacted using needle,screed and plate vibrator and finished in continuous operation including provision of contraction and expansion,construction joints,applying debonding strips,primer,sealant,dowelbars,near approaches to bridge/culverts and construction joints,admixture as approved,curingof concrete slabs for 14 days.

SONLAL BODO (BID ID -250104)