SPL REPAIR TO BOUNDARY WALL, FENCING AND GATE OF CERTAIN MD ACCN, ADDN/ ALTN TO ABUTMENTS AND CONNECTED ITEMS NEAR KK BRIDGE, PROVN OF DRAIN COVERS AT VARIOUS LOCATION UNDER GE EAST MATHURA

Demolition of brick work built in cement mortar including all quoins, asches, pillars etc in any position complete all as specified and as directed.

Demolition of cement Concrete (unreinforced) of any description and in any position below or above ground level complete all as specified and as directed.

M&L for brick work with old size burnt clay sub class 'B' bricks built in CM 1:6 straight or curved on plan exc 6 m mean radius complete all as specified and directed.

All as per item serial No 03 here-in-before but except bricks (obtained from item No 01) complete all as specified and as directed .

M&L for removing mortar from old size sub class bricks obtained from demolition built in cement mortar and cleaning bricks, stacking for measurement including all extra handling and removal and disposing off rubbish complete all as per specified nd directed.

M&L for 10mm thick rendering in cement mortar (1:6) on fair faces of brick of boundry wall concrete surfaces finished the surface even and fair without using extra cement complete all as specified

M&L for 15mm thick rendering in cement mortar (1:6) on other than fair faces of brick/ concrete surfaces of finishing the surface even and fair without using extra cement complete all as specified.

M&L for preparation of new plastered surface of walls and applying two coats of cement base paint over and including a coat of alkali resistant primer complete all as specified and as directed.

M&L for Providing, cement concrete (1:2:4) type B1 using 20 mm aggregate in copings, kneelers, apex stones, bed plates, kerbs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for 35mm thick precast cement concrete type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in louvers and jallies including all mouldings posts etc set in CM 1:4 including dismantling of old Jafries/ Jallies and removing ffrom site complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded in natural ground/ PCC/ Brick work and making good disturbed area complete all as specified.

S&F Mild steel work as in hand rails , half round or other section, balusters running bars, nosing to steps, wind ties, posts and struts in fencing incl cutting tops to shape as required, drilling holes , noching for wire , flat iron fillets for securing wiremesh etc., incl all necessary drilling, bolting or riveting etc & similar work conforming to Fe-290 Gde E-165 and all as specified.

S&F in repair galvanised 2 strand steel barbed wire 2.24mm, dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provn of galvanised mild steel wire staples or steel pins all as directed. (Each line wire to be measured)

S&F in repair Concertaina coil 450 mm dia with 2.50 mm dia high tensile strength wire fixing to Y-shaped angle iron posts securing with necessary clips on top of boundary wall all as specified and as directed.

S&F 5 to 10mm dia Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long complete all as specified.

S&F in repair 2mm thick Fiber reinforced plain sheet of high tensile strength for fixing with MS frame with screw, washer and nut bolt as specified and directed.Note: Colour and design shall be approved by GE(E) Mathura.

M&L for Preparing new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic paint over and including one coat of red oxide primer complete all as directed

M&L for Preparing new steel surfaces of any description, n.exc 10cm in width or girth when unconnected with other painting or when painted in a different tintsurfaces and applying two coats of synthetic paint over and including one coat of red oxide primer complete all as directed

M&L for PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation & mass concrete etc complete all as specified.

M&L for PCC 1;3:6 type C-2 using 40 mm graded stone aggregate as in foundation & mass concrete etc complete all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc.

S&F for MS framed work as in doors or gates of angle or other sections with gasset plate rails braces etc complete drilled for fixing of steel sheeting or other covering to doors etc to be prepared for hanging or sliding with and including either hooks and pintel hinges or steel hanging door etc, (inclusive of steel sheeting or other covering running rails & guides) also fastening and fixing complete.

Demolition of Stone slabs and tiles of any description or thickness (except ceramic tiles) in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and directed.

M&L for 16-18 mm thick Z- black Granite slab work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like laid over and including 20mm thick screed bed in cement mortar 1:4 and pointing in white cement (1:2 )using marble dust with admixture of pigment to match with shade of granite, including rounded/half rounded edge and providing hole for gas pipe in pre-cast slab as well as in granite slab of cooking platform complete all as specified and as directed.

M & L 15mm thick rendering in CM (1 :4) on fair faces of brick walls or concrete surfaces etc. and finished even & smooth without using extra cement complete all as specified.

M & L 15mm thick rendering in CM ( 1 : 4 ) on other than fair faces of brick walls or concrete surfaces etc. and finished even & fair without using extra cement complete all as specified.

M&L for PCC 1:2:4 type B-2 (using 40mm graded stone agg) as in surface channel bed/drains/in manholes all as specified laid to slope and finished surface even and smooth complete all as specified & directed.

Extra for forming fair finished drain or channel upto 60cm inner girth in cement concrete using extra cement incl forms moulds, mitered/stopped ends etc. complete all as specified & directed.

M&L for factory made perforated heavy duty HD-20 Precast Cement Concrete manhole covers 75 mm thickness and size (0.60m x 1.20m) consisting of MS iron fillet along the perimeter of sides and weight of cover should not be less than 80kg all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in soft/ loose soil complete all as specified and directed.

Excavating over areas, exc 1.5 m but n exc 3.00 m deep and getting outin soft/ loose soil complete all as specified and directed.

Returning/filling in trenches in soft/loose soil including spreading watering, well ramming in layers n.exc 25 cm thick after laying and testing of pipe complete all as specified & directed.

Removing excavation material surplus soil to a distance n.exc 250m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified & directed.

M&L RCC 1:1.5:3 type A1 (20mm graded aggregate) nominal mix as in foundation, including rafts footing , plinth beams, base for columns etc complete all as specified and directed.

M&L RCC 1:1.5:3 type A1 (20mm graded aggregate) nominal mix as in Walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilaster and buttresses complete all as specified and directed.

M&L for Form work to sides of concrete foundations, footings, bases of columns, raft, and raft beaams sides and soffits of foundation and plinth beams and similar work flat fair finished surfaces etc complete.

M&L for Form work to to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter fair finished of surfaces complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length bent to shape required including cranking, bending spirally for hopping for columns, hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips quality conforming to fe 410-S complete all as specified & directed

M&L for brick work in cement mortar 1:4 with fly ash bricks straight or curved on plan exc 6m mean radius with old size bricks complete all as specified & directed. (for manhole etc).

M & L 15mm thick rendering in CM ( 1 : 6 ) on other than fair faces of brick walls or concrete surfaces etc. and finished even & smooth without using extra cement complete all as specified.