PROVN OF WELDING SHOP EQPMT STORE BULK STORE FOR SPARES PARKING SHED FOR LT VEHS AT WKSP AREA AND SPL REPAIR TO ROOF TREATMENT AT VARIOUS LOCATIONS UNDER AGE BR II AND AGE EM OF GE BENGDUBI

Amount

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and directed.

Excavating in post holes( or similar holes) each n exc 0.50 cum , getting out,returning filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft/ loose soil complete all as specified and directed.

Surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

M&L for Sand filling under floors or in foundation including watering and consolidated and compacted with clean dry sand complete all as specified and directed.

Removing excavated material (soil) n exc 50m and depositing where directed at a level n exc 1.5m above the starting point complete all as specified and directed.

Removing excavated material (soil) exc 250m but n exc 500m and depositing where directed complete all as specified and directed.

M&L for hardcore of gauge n.exc. 63 mm, with broken stone or boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surfaces complete all as specified and directed.

M&L for cement concrete 1:4:8 type D2,using 40mm graded crushed stone aggregate as in foundations filling and mass concrete complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in copping and filling in back of chowkat the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

M&L for RCC(Nominal mix) type B1, 1:1.5:3 (using 20mm graded crushed stone aggregate) as in foundation,including rafts,footings,foundation beams plinth beams bases for columns etc. complete all as specified and directed.

M&L for R.C.C, Nominal mix of 1:1.5:3 using 20 mm graded crushed stone aggregate as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves etc all as specified and directed.

M&L for R.C.C 1:1.5:3 (Nominal mix) type B-1 using 20 mm graded crushed stone aggregate for Beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed.

M&L for RCC(Nominal mix) type B1, 1:1.5:3 (using 20mm graded crushed stone aggregate) as in Columns, pillars, piers, posts and struts etc. complete all as specified and directed.

M&L for RCC(Nominal mix) type B1, 1:1.5:3 (using 20mm graded crushed stone aggregate) as in chajja , shelves and like etc. complete all as specified and directed.

Supply only integral water proofing compound liquid grade conforming to IS-2645 complete all as specified and directed. (Pidiproof of Dr.fixit or equivalent)

M&L for brickwork with old size fly ash bricks, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 complete all as specified and directed.

M&L well burnt old size sub Class ‘B’ bricks, laid in trenches for cable protection complete all as specified and as directed by the Engineer-in-Charge.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams,sides and soffits (if any) of foundation and plinth beams; and similar work; vertical to rough finished surface complete all as specified and directed.

M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) rough finished surface flat complete all as specified and directed.

M&L for formwork to chullah hoods, chajjas, troughs and similar items in cluding edges complete all as specified and directed.

M&L for formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, columns and stanchions rough finished surfaces of concrete, square, rectangular or polygonal in shape complete all as specified and directed.

S&F 35mm thick factory made flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 200mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and direcetd.

S&F 150mm size aluminium handle cast type complete all as specified and directed.

M&L for MS framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment etc conforming Fe-410W(GdeE-250) quality -A complete all as specified and directed.

M&L for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240 conforming to Fe 410 -W (Gde E- 250) quality A complete all as specified and directed.

S&F steel window with side hunge shutters including projecting type hinges with steel handle and steel peg stey, tower bolts etc. complete with glazing bars dovetailed or welded complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

M&L for 1.25mm thick pressed steel door frame of size 105mm x 60mm with one or more rebates including necessary fixing lugs , hinges, lock strike plate etc complete all as specified and directed.

S&F 0.5mm thick Plain, Aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (length and girth as fixed complete all as specified and directed.

S&F Pre- painted coloured trapezoidal profiled Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP x RW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

S&F Pre- painted coloured plain sheet Galvalume/ Zincalume sheet with min thickness 0.50mm TCT confirming to IS - 513(AZ-150 GSM, Al Zn allay metalic coating with 550 Mpa yield stress as per AS-1397) as in roof covering/cladding to wall, fixed with self tapping screws colour exterior coat of silicon modified polyster/BHP/ XRW paint system 20 micron top coat applied over 5 micron primer and 5 micron polyster back coat applied over 5 micron primer , all fixed with galvanized self drilling self tapping fastner (12-14 x 55 with EPDM seals) complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates) as in flooring to receive to tiles etc complete all as specified and directed.

M&L for 75mm thick PCC type C2,1:3:6 using 40mm graded crushed stone aggregate as in sub base floor complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C1 (using 20mm crushed graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for sheet glass, 4mm thick, ordinary quality and glazing with oil putty in squares n exc. 0.50 Sqm each pane complete all as specified and directed.

S&F 4.0mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sqm in each pane complete all as specified and directed.

M&L for preparation of untreated new wood/wooden surface of any description over 10cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M&L for two coats of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth including preparation of surfaces complete all as specified and directed.

M&L for 40mm dia GI pipe Light grade with all necessary fittings laid in trenches, fixed to wall/pole/under road/floor etc for cable protection complete all as specified and as directed.

Taking up or down steel tubing and connections,including cleaning for re?fixing or removal to store bore of pipe 20 mm complete all as specified and as directed

Taking up or down steel tubing and connections,including cleaning for re?fixing or removal to store bore of pipe 25 mm complete all as specified and as directed

Disconnecting existing tanks of capacity exc 500 ltr but not exc 1000 ltr, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position. (Cleaning repairing, etc. measured separately) complete all as specified and as directed

Dismantling water tanks and removing to store exc 500 ltr but not exc 1000 ltr capacity complete all as specified and as directed

S&F rotational moulded PVC water storage tank 1000 ltrs capacity conforming to IS-12701(1989) cylindrical vertical type double-layered with closed top (thereated) including inlet,outlet and wash out holes of approved make hoisted and fixed in position all as specified in SSR Part I etc completge all as specified and directed.

S&F ball valves for 20mm bor dia of pipe high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0mm-210gms./25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

Demolition of Concrete un- reinforced of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings incl ridges, hips and valley gutter complete all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over and including cement screed base 15mm thick in cement mortar 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing complete all as specified and directed.

M&L for machine cut kota stone in riser, dado, steps, skirting etc 20-25mm thick of size over and including 10mm thick cement rendering in cement mortar 1:3 laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing,grinding and polishing complete all as specified and directed.

M&L for 25mm thick cement concrete type B-1, 1:2:4 (using 20 mm graded crushed stone aggregates) as in flooring, finished the surface even and rough complete all as specified and directed.

M&L for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of M-30 grade with approved colour, design & pattern as in footpath,parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of coarse sand,compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver block as per required size and pattern, finishing and sweeping extra sand;complete. complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm +5mm in cement mortar 1:4 on external surfaces of brick work or concrete surfaces with using WPC finishing the surfaces even and smooth without using extra cement complete all as specified and directed. Note:- WPC will be measured and paid separately under respective item of this schedule.

M&L for newly plastered surface of wall and appying two coat of white or tinted oil bound distemper over one coat of alkali resistant primer complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coat of cement base paint complete all as specified and directed.

M&L for preparation of new surfaces of wall with Chalk whiting, on plastered surfaces,prepara-tory to distempering with and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed

M&L for Coving (50mm X 50mm ) to be done at all junctions with Nitobond SBR latex to be mixed with cement,complete all as per manufacturer specifications and instruction, specifried and as directed.

Taking down existing un-sreviceable water proofing treatment from roof slab and cleaning the roof by wire brush and removing WPT felt beyond the MOD premises etc. cement plaster on brick or stone walls, etc.complete all as specified and directed.

M&L for waterproofing coating by providing and applying Fosroc Brushbond Roof Guard of FOSROC or equivalent of SIKA/STP , a single component High build fibre Reinforced Acrylic waterproofing render for roofing system applied by brush, at three coats at minimum dry film thickness of 1 mm, cured by reaction with atmospheric moisture to give a tough elastomeric waterproof membrane complete all as per manufacturer specification, specified and directed. Solid Content - 70%, Tensile strength ASTM D 412-1.10 Mpa, Elongation ASTM D12-100%, Resistance to ageing due to - 1000hours, UV radiation ASTM D4587 E - No Change, Rapid Chloride Penetration ASTM c 1202 - Very low, Pull off adhesion ASTM D541 - 0.92 Mpa, Resistance to Algae growth ASTM D 5589-97 - Passes, Zero rating, Permeability (mm) (BSEN 12390 part 8) -n 5.0, Water vapour transmission (ASTM E 96) - 6.0g/m2 h

M&L for Treatment of crumple joint (Floor portion) after preparation of structural concrete surface (floor portion) and remove existing plaster work by manual means with chisel, hammer, wire & normal brushes, to clean & remove all loose cementitious slurry, small concrete lumps, oil/ grease etc completer at all level and Supply and apply polysulphide sealant (Thioflex 600 GG) of Fosroc or equivalent of SIKA/STP in gap of the expansion joint using filler material and breaker rod over sealant primer complete all as per manufacturer specification, specified and directed.

M&L for Treatment of crumple joint (Vertical portion) after preparation of structural concrete surface and remove existing plaster work by manual means with chisel, hammer, wire & normal brushes, to clean & remove all loose cementitious slurry, small concrete lumps, oil/ grease etc completer at all level and Supply and apply Exponband one with adhesive Nitobond PC40 of Fosroc or equivalent of SIKA/STP on the both side of the joint in the prepared substrate. Apply the Fosroc Expoband one (200mm*1mm) on the adhesive of Fosroc or equivalent of SIKA/STP. Apply Nitoband PC40 of Fosroc or equivalent of SIKA/STP properly and hardened before the top layer is applied protection layer of aluminum sheet over the treated area of expansion joint complete all as per manufacturer specification, specified and directed.

M&L for sand cushioning for protection of underground cable, consolidated and compacted with clean dry sand complete all as specified and directed.

M&L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 10Sqmm 2 core laid in trench/pole/on wall completer all as specified and directed.

M&L for XLPE insulated GI wire/Strip armoured Electric power cable (Heavy duty) with stranded Aluminium conductor 1100 Volts grade, cross sectional area 25Sqmm 4 core laid in trench/pole/on wall completer all as specified and directed.

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 1.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 1.5 sqmm size through and including 20mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed for the followings: -

One light point/ Bell/ one fan point controlled by one switch

One 3 pin socket outlet, 6 Amp on the same board with other switches

One 3 pin socket outlet, 6 Amp independent

M&L for concealed point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables 1100 Volts grade of 2.5 sqmm size alongwith one earth continuity conductor with FRLSH PVC insulated unsheathed multistranded copper conductor cable 1100 Volts grade of 2.5 sqmm size through and including 20 mm dia (medium grade) rigid non metallic PVC concealed conduit terminated in and including pressed steel sunken boxes , readily available (Having wall thickness not less than 1.22 mm for boxes upto a size of 200 mmX300 mm and beyond that the wall thickness shall be not less than 1.63 mm) concealed type with 3mm thick bakelite sheet cover for fixing of switches, sockets, fan regulators etc including testing on completion complete including cutting chases for concealed conduit pinning in making good to facing and pointing in using cement mortar 1:3 and making good to disturbed surface complete all as specified and directed.

BLANK

S&F Switch piano, flush type single pole, one way 6 Amp complete all as per specified and directed.

S&F Switch piano, flush type single pole, one way 16 Amp complete all as per specified and directed.

S&F Socket outlet 2 in 1, 6 pin, 6 and 16 amp flush type complete all as per specified and directed.

S&F Socket outlet 2 in 1, 5 pin, 6A complete all as per specified and directed.

S&F Sheet metal enclosure powder coated for MCB DB double door single pole & Neutral 8 way with 200Amp common bus bar at incomming complete all as specified and directed.

S&F Sheet metal enclosure for MCB DB double door 415V Triple pole & Neutral 4 way with common bus bar at incomming end complete all as specified and directed.

S&F Ceiling rose, 3 phase/PVC/polycarbonate, isolated body complete all as per specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES SSR Part-I connected to earthing test point all as specified or indicated including testing on completion complete all as specified and directed.

S&F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. as reqd complete all as specified and directed.

Supply and fixing 240V, 10KA 'C' curve single pole miniature circuit breaker (MCB) 6 to 32 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

Supply and fixing 240V, 10KA 'C' curve SPN miniature circuit breaker (MCB) 40 to 63 Amps, in the MCB DB complete with connection testing and commissioning. complete all as specified and directed.

Supply and fixing 415V 10KA 'B' curve miniature circuit breaker (MCB) TPN 40 To 100 AMP in the DB complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230V,1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fixing LED tube light batten box type made of CRCA sheet with decorative end caps suitable with ultra bright glass LED tube light 1x 18/20 watt T8 type single side connection complete with both end bi-pin holder and all accessories internally prewired and fixed to wall/ceiling incl fittings accessories and connecting up with twin core flexible copper conductor cable suitable size complete all as specified and directed.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25 watts with pre wired and necessary mounitng arrangements and provision of 1.5 sq mm three core copper dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed.

(Note : The Scope of Work contained in 'Sch of Credit' amounting to Rs. 1,290.00 (refer Tender Srl Page No 26). The Quoted sum shall be arrived at after deducting the amount of “Sch of Credit” from the total amount of the ‘BoQ’

M/S Vaishno Constructions (BID ID -3380353)

M/S R. K. INDUSTRIES (BID ID -3384783)

M/S JANATA CONSTRUCTION (BID ID -3379885)

M/S KAR CONSTRUCTION (BID ID -3383418)

Shree Ram Construction (BID ID -3384572)

SHRI S K BHATTACHARJEE (BID ID -3383121)

M/S CONTRACTS (BID ID -3383194)