PROVN OF CERTAIN MINOR REVENUE SPECIAL REPAIR AND ADD ALT WORKS IN THE AOR OF GE CENTRAL KIRKEE

Amount

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) removing servicable tiles to store and rubnbish of the permises.

Demolition of stone slab and tiles of any description or thickness in floor apron etc complete all as specified and directed.

M & L for 25mm thick cement concrete 1:2:4 type B-1 using 20mm crushed stone aggregate in levelling course for receiving floor tiles complete all as specified and directed.

M&L for Non Skid joint free ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles over and including cement screed 15mm thick in CM 1:6 complete all as specified including demolition of floor or wall tiles, stone slab of any description or thickness laid ,bedded and pointed in any mortar all as specified.

M&L for glazed coloured ceramic tiles of size 300x200x5 to 6mm thick in verticle surfaces as in dado/skirting set and jointed in neat cement slurry and pointed in coloured cement to match shed of tiles over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified including demolition of floor or wall tiles, stone slab of any description or thickness laid, bedded and pointed in any mortar all as specified.

M&L Vitrified ceramic tiles 10mm thick (square/rectangular) area of each tile not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles laid over cement screed 15mm thick in CM 1:6 complete all as specified.

All as per item No 7 above but on vertical surface such as in skriting/dado etc over backing coat of 10mm thick rendering in CM 1:4 complete all as specified.

Taking down chowkats and frame n.exc 1.5 Sqm each including shutters without taking off shutters from the frame and removing from site.

Taking down chowkats and frame exc 1.5 Sqm but n.exc 4.00 sqm each including shutter wiuthout taking off shutter from the frame and removing from site.

S & F Pressed steel door frame for doors of size 125 x 60mm with double rebate including necessary fixing lugs, hinges, lock strike plate, etc complete including and of hollow section of frame with and including PCC 1:2:4 type B-0 complete all as specified.

S & F Pressed steel door frame for doors of size 105 x 60mm with one or more rebate including necessary fixing lugs, hinges, lock strike plate, etc complete and filling of hollow section of frame with and including PCC 1:2:4 type B-0 complete all as specified.

S&F Flush shutters 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides with covered with decorative face verneer with lipping/frame to match complete.

S & F 35mm thick 2nd class HW glazed or skelton shutter open rebated divided into square with plain chamfered or rounded mitred and rebated with out sash bar and prepared to receive gauze or glaze, size of members as clause 8.20 (a) of SSR pt-1 complete all as specified.

S & F 35mm thick plain, framed panelled factory made shutters (two panels) door with lock rail and panel of 12mm thick veneered wood board with commercial veneering on both faces and with second class hard wood rails and styles. The size of rails and styles as per IS-1003 (Part-I) kiln seasoned and chemically pressure treated.

M & L aluminium alloy powder coated windows including aluminum powder coated frames sliding track, bottom weighing not less than 1.015 kg/RM, sides and top not less than 0.826 kg/RM double revated and 0.55 kg for window shutter with one fixed glazed shutter and two nos glazed/gauged shutter sliding type with aluminium sections as per series - A (15mm) 3 track of Jindal section numbers for sliding windwos with framed shutter including aluminium allow powder coated snap type beads handles with locking arrangement spring action and glazing clip joint cleats rubber gaskets etc including provision of 5.5mm thick tinted glass/frosted glass of superior quality and stainless steel jali including all standard fittings complete all as specified & directed.

S&F aluminium powder coated window sliding type (3 track) with frame size 100x35x1.2mm thick and shutter frame size 39.40x17.70x1.2mm thick with two glass shutter and one mesh shutter including necessary jointing cleats, glazing clips, rubber packing, powder coated aluminium snap beading screws with and including 4mm thick plain float glass and 0.56mm dia apperture 1.4mm SS wire mesh and fittings etc complete all as specified and directed.

S&F aluminium louvered ventilators of section size 80mmx20mmx1.50mm including 5mm thick frosted glass fixed in half portion & adjustable type louvers in another half and stainless steel wire mesh fixed type on outside frame etc.incld taking down existing steel ventilator all as directed.

M&L for Gypsum reinforced boards 600x600x8 to 10mm thick for ceiling on Hot dipped Galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick GS sheet and of size 24x32x3000mm and spaced at 1200mm centers securely fixed to the structural soffits by approved hangers at 1200mm maximum centers. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, level and justers and screws etc. The last hanger at the end of each main runner shall not be greater than 450mm from adjacent wall. Flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runners at 600mm center to form 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm modules to be formed by fitting 600mm long cross Tee centrally between the 1200mm cross tee. Tee, Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacture instruction, including taking down wall/ceiling boards(fibre, pulp insulation etc) or inslutation boards any thickness incl fillets and frame works complete all as directed.

M & L for preparation of plastered or unplastered old decorated surfaces of walls including brooming down or scraping down with steel wire brushes of smoke spots , moulds ,moss efflocerent salts and treading oil and greasy spots and applying two coats of oil bound distemper over one coat of primer over 3mm thick wall care putty 'Birla White' complete all as specified and directed.

Taking down cement plaster on brick or stone walls or concrete surfaces etc incld raking out joints, hacking for key, scrubbing down with water all as specified as directed.

M & L rendering 15 mm thick on concrete surfaces in CM 1:6, finished even and smooth 'with sagol complete all as spd and directed by Engr-in-Charge.

M & L for preparing newly plastered surfaces of wall incl preparation of surfaces and applying two coats of oil bound distemper over a coat of primer over 3mm thick wall care putty on wall surfaces complete as specified and directed.

S & F Rotational moulded polyethylene water storage tanks 500 lts capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position including 20 mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed including taking out existing unserviceable overhead tank of any description in any position complete all as directed.

S & F 15 mm bore dia steel water tubings medium grade galvanised with and including all medium grade fittings fixed complete to walls and ceilings or laid in floors including taking up or down existing pipe lines complete all as specified and directed by EIC.

S & F 20mm bore dia steel water tubings medium grade galvanised with and including all medium grade fittings fixed complete to walls and ceilings or laid in floors including taking up or down existing pipe lines complete all as specifiedand directed by EIC.

M&L for cutting existing steel tubing bore of pipe 15mm for alterations or additions (each cut measured) complete all as directed.

M&L for cutting existing steel tubing bore of pipe 20mm for alterations or additions (each cut measured) complete all as directed.

S & F 15mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F 20mm bore Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed.

S & F in repair Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed to 20mm bore dia of pipe complete all as specified and as directed.

Excavation in trenches n.exc 1.5 M wide and n.exc 1.5 M depth for foundation and n.exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and direted.

Excavation in trenches not exceeding 1.5 m wide & not exceeding 1.5 m in depth or n.exc 10 sqm on plan and not exc 1.5 m in depth for foundations etc and getting out as in Soft disintigrated rock complete all as specified and directed.

M&L for PCC (1:4:8) type-D2 using 40 mm graded stone aggregate as in foundations & filling in Mass concrete complete all as specified and directed.

M&L pre-cast cement concrete(20mm graded crushed stone aggregate) 1:3:6 type C-1 as in block masonery with solid block masonery with solid blocks,exc.10cm in width and setting in cement mortar 1:6 all as Specified.

Material and labour for PCC 1:2:4 type B2, including necessary formwork using 40mm graded crushed stone aggregate, as in surface channels and drains etc including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed by Engr-in-Charge.

M & L for providing cement concrete type B-1 (1:2:4) using 20 mm graded crushed stone aggregate as in coping/benching and the like including necessary form work complete all as specified.

Material and labour for 15mm thick rendering in CM 1:4 over concrete/brick surfaces finished even and smooth without using extra cement mixed with water proofing compound pidilite LW @ 200ml per 50 Kg cement as per manufacturer instructions complete all as specified and directed by Engineer-in-Charge (WPC will be measured and paid separately).

Supply only liquid water proofing compound pidilite LW complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc. 25cm in soil all as specified and directed.

Removing excavated soil material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point all as specified and directed.

M&L for pre cast cement concrete solid block masonry 10cm thick with solid block of the grade C-1, (1:3:6) using 20mm graded agg set in CM (1:4) complete all as spd and directed.

M&L for filling under floors with moorum / red bajri laid in layers not exc 15 cm thick spread levelled and rammed including watering all as specified and directed.

M&L hard core of broken stone or boulders gauge n.exc 63 mm, and deposited , spread and levelled in layers n exc 15 cm thick watered and rammed to a true surface all as specified and directed.

M&L plain cement concrete 1:4:8 type D-2 using 40 mm graded aggregate as in sub base of floors 75 mm thick all as specified and directed

M & L cement concrete 1:3:6 type C-I (20 mm graded aggregate) as in floors plinth, path etc 75 mm thick in alternate bays finished even and smooth surface with out using extra cement.

S & F Pre painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, fixed with self tapping screws complete all as directed.

S & F rolled MS section as in roof trusses (framed), trussed, purlins, rafter, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc fixed with angle cleats or other connecting plates confirming to Fe 410-W quality B complete.

M&L for Rendering 10mm thick, on fair faces of brick work or concrete surfaces of walls in CM 1:6 all as specified and directed by EIC

M&L for rendering 5mm thick in CM (1:4) with using water proofing compound over 10mm thick in CM (1:6) on external surface of walls of stone masonry surfaces finished even & smooth all as specified and directed by EIC. (Note: WPC shall be measured and paid seperately for top 5mm thick plaster only)

M&L for preparaing newly plasered surfaces of walls including preperation of surfaces and applying two coat of cement base paint on walls surfaces complete .

M & L for preparing new steel surfaces of any description, over 10cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F pillar taps fancy type 15mm dia bore, cast copper alloy with capstan heads, chromium plated screwed down high pressure, with long screwed shanks and fly-nuts screwed for iron pipe all as specified and directed.( Make : Czar/ ESS or equivalent)

S&F Chromium plated fancy type 15mm dia bore stop valve, cast copper alloy with crutch or butterfly handle, screwed both ends for iron pipe all as specified and directed.

S&F Vitreous china wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe all as specified and directed.

S & F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum),with grating and union for discharge pipe (exludging flushing, waste pipe) complete all as directed.

S&F urinal spreader of PTMT any colour for fixing with 15mm dia pipe, complete all as specified.

M&L 32mm dia waste fittings for pipe, brass chromium plated for glazed ware urinals, basins, etc and fly-nuts, flange end bedded in red lead cement and otherend fixed all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors.

S&F 75mm dai PVC (SWR) bends any radius all as specified and directed.

S&F 75mm dai PVC (SWR) junction single (Single T) equal or unequal all as specified and directed.

S&F 75 mm dia outlet PVC (SWR) Nahani trap plain with grating incl jointing with solvent cement all as specified and directed.

Excavating in post holes not exc 0.5 cum, in hard/dense soil and getting out , returning , filling in and ramming earth in layers not exc 25 cm, watering and removing surplus soil to a distance not exc 50 m and making good surfaces all as required.

M & L PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in fdn, filling and mass concrete in posts holes.

S & F MS plate 6 mm thick plain, cut to shape forming holes and welded to truss and verticle post all as specified and directed.

S & F MS screw bolts machine made with hexagonal or square heads at one end and screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, dia of shank 5 to 10mm and length exc 5cm and n exc 10cm complete.

S&F for Galvanised, corrugated mild steel sheeting bent to curve (of any reduius) 0.63 mm thick with two corrugation side lap fixed with L or J type hook with washer and including necessary fittings by using class 8 type sheets , including dismantling of plain or corrugated steel sheeting any gauge thickness including Nainital or similar pattern as in roof covering/vally gutters.

Dismantling mild steel work of any description and in any position complete all as directed by Engr-in-Charge.

Demolition of cement concrete in ground floors and pavings of any description and in any position and removing debris out side MD land complete all as directed.

M & L for PCC 100 mm thick 1:2:4 type B2 as in hardstanding/floor (using 40mm graded stone aggregate) finished even & smooth without using extra cement complete all as directed.

Demolition of Brick Masnory or stone masnory including PCC coping built in cement mortar complete all as specified and directed by EIC.

M&L Brick work with sub class 'B' brick straight or curved on plan built in cement mortar 1:6 all as specified and directed.

M & L for cement concrete 1:2:4 type B1 (using 20mm graded stone agg) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed.

Racking out joints/pointing to random rubble or polygonal rubble uncorsed or brought up to courses masonry built in cement or lime mortar, complete all as specified.

M & L for preparation of old painted steel surfaces of any description over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamal paint complete all as specified and directed.

S & F coloured non skid ceramic tiles 300 mm x 300 mm x 6 to 7mm thick,in floors set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15 mm thick screed bed in CM 1:6 all as specified.

S & F in repairs water closet (Squat Pattern) complete incl provn of lime concrete bedding Orissa pattern size 580 x 440mm white with integral foot rests (excluding flush pipe or flushing cisterns) including connection to trap and flushing pipe anti syphonage pipe etc complete and making good to floor to match with existing complete all as specified and directed.

S & F in repairs PVC High/Low level flushing cistern 10 litres capacity including all fittings i.e float valve, syphon, flushpipe,brackets all as specified and directed by EIC.

S & F in repair cast iron floor trap square type with CP grating with or without hole including provision of jointing to waste pipes in run lead joint dia of outlet 75 mm, complete all as specified.

S & F in repairs CP bib tap long body fancy type ISI marked cast copper alloy with crutch or butterly handle screwed down high pressure and screwed for iron pipe of 15mm bore complete all as specified.

Supply and fixing in repairs 15mm dia PVC connection with brass check nut of length 450mm complete all as specified and directed by Engr-in-Charge.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out in soft/disintegrated rock.

Material and labour for screed bed or bedding layer of mortar 20mm thick average thickness for laying floor finishes in cement mortar 1:6 complete all as specified.

Material and labour for PVC moulded vibratory system chequered cement concrete tiles glossy finish with grey cement and pigments 30 cm x 30 cm x25 mm thick, set jointed and pointed in neat cement slurry to be laid over screed bed complete all as specified.

M&L for rendering 5mm thick in CM (1:4) with using water proofing compound over 10mm thick in CM (1:6) on external surface of walls of block masonary finished even & smooth without using extra cement complete all as specified and as directed. (Note: WPC shall be measured and paid seperately for top 5mm thick plaster only)

Supply only integral water proofing compound.

M & L for timber, 2nd class WH, plain fillets, square, rectangular or triangular in section, wrought, fixed with screws, sectional area exc 15cm but n. exc 25sqcm.

S&F for 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete as making good to wall all as specified.

S & F 100mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified.

S & F Galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm all as specified.

S & F 200mm long Aluminium anodised, barrel tower bolts of extruded section complete all as specified.

S & F Aluminium handles, cast type, anodised of size 150mm, fixed with screws or welded, complete all as specified.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

M&L for pressed steel door frame of size 165 x 60 mm for door with one or more rebates including necessary fixing lugs hinges locks strike plate etc complete all as specified and directed, supplied and fixed

S & F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165.

M&L for Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, etc treating ends of posts, backs of chowkats area tarred exc 0.1 sq. m but n exc 0.5 sq. m each etc., treated with tar or coal tar black paint complete all as specified and directed.

S&F Door closer hydraulically regulated, Aluminium (extrude section) body designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg, complete all as specified and directed.

M & L for preparing new or previously untreated wood surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified

Forming jambs, etc. to openings (to foregoing item), including cutting, tooting and properly bonding into old work, also facing, jointing and pointing to match existing work, in Cement mortar 1:4 complete.

S&F for 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified.

S & F Steel windows (Factory Made) with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete but without glazing bars , dovetailed or welded complete making good to wall all as specified and directed.

S&F Door closer hydraulically regulated, Aluminium (extrued section) body designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 36 kg, complete all as specified and directed.

S & F for aluminum alloy powder coated door including frame and channel of section (Door frame single groove 101.6mm x 44.45mmx1.25mm, shutter top section 47.62mm x 44.45mmx1.25mm thick, shutter bottom section 114.30mm x 44.45mm x 1.25mm thick, shutter vertical section 85mm x 44.45mm x 1.80mm thick, shutter middle section 83.50mm x 44.45mm x 1.25mm thick & glazing clips weighing not less than 0.097 kg/RM) incl shutter fixed to sliding type/openable frame and channel as directed and approved by GE and as per IS specifications including provn of 5.5mm thick tinted glass/12mm thick prelaminated particle board as required including handles, tower bolt, door stopper complete all as specified & directed.

S & F aluminium alloy powder coated glazed or skelton shutter including frame of section ( door frame single groove 85mmx45 mm x 1.25mm thick, shutter top section, bottom section, middle section and vertical section 65 mm x 45 mm x 1.25 mm thick and glazing clips weighing not less than 0.097 Kg/RM ) including shutter fixed to frame as directed and as per IS specifications including S & F mild steel wire cloth 0.56mm dia and apperture 1.4mm and required handles, tower bolt,rubber gasket complete.

M&L for 100 mm thick PCC 1:4:8 Type D2 using 40 mm graded stone aggregate as in sub base of floor, mass concrete finished even and fair all as spd and directed.

M&L for Sand filling under floors or in foundations including watering and consolidation for laying floor finishesh.

M & L for Coloured glossy finished Machine pressed precast concrete interlocking paver block (Two colour combination) any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment laid over sand cushion.

Demolition of cement concrete unreinforced in ground floors and pavings n.exc. 15cm thickness below or above ground level all as specified.

Surface excavation n.exc 30 cm deep and averaging 15cm deep and getting out in soft/ loose soil

M&L mild steel TMT bars10mm dia and over, cut length, bent to shape required , including cranking , bending spirally for hooping for coloumns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified.

All as per srl item-112 above but 6 to 8mm dia as in stirups binders and spacers.

M&L PCC 1:3:6 typeC-2 (using 20mm graded stone agg) 75mm thick sub base

S&F 2nd class soft wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as directed by Engr-in-Charge.

S&F for 35mm thick 2nd class soft wood plain framed paneled shutters (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers, Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F for powder coated aluminium sliding windows having three Nos of tracks including one wire glazed shutters for mosquito proofing including stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm and two Nos glass shutters including 4mm thick coloured glass and aluminium section weight n.less than 0.55 Kg/RM including necessary cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, suitable handles, locking arrangement and fixed to stone masonry wall complete.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165 complete.all as specified and as directed by the Engr-in-Chage

Material & labour PCC (1:3:6) type C1 (using 20 mm graded stone aggregate) as in hold fast , bed block and like complete all as specified and as directed by the Engr-in-Charge.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section complete.

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth without using extra cement in cement mortar 1:6 complete all as specified and as directed

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed

S&F MS Rolled sections in main and cross beams,hip and jack rafters ;purlins where connected to common rafters running rails and guids for sliding doors ;fixed with angle cleats or other connecting plates and similar work confirming to Fe-290, Gde-E-165 complete all as specified and as directed.

S&F 0.63mm thick Galvanised corrugated mild steel sheeting with two corrugations side lap,fixed with coach screws and washers in roofs walls etc. with grade of zine coating 275.

M&L for preperation of new plastered wall surface of any description and applying three coat of white wash complete all as specified and as directed.

M&L for RCC 1:2:4 type B1 using 20mm graded stone aggregate in beams lintels over 1.5m span etc complete.

M&L for form work to sides of concrete in roof beams, lintel beam and similar work, vertical or to batten rough finish flat surfaces on concrete all as specified.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 (Brackets over 10 kg each to be measured under 'Structural Steel')

M&L for rendering 10mm thick in CM (1:6) on internal surfaces of walls of block masonry finished even & smooth without using extra cement.

Supply only integral water proofing compound.

M & L for glazed ceramic coloured tiles (300x200mm) x 7 mm thick in Dado/Skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 10 mm thick backing coat in CM (1:4).

S&F for galvalume sheets having pitch 190mm, depth 29mm and thickness not less than 0.50mm (Galvume base-PPGL trapezoidal profile sheets) fixed with self tapping screw and aluminium washer of suitable size in roof covering all as specified. (Over lap shall be as specified by manufacturer)

S&F for aluminium anodised louvered ventilator with 4mm thick pin headed glass and 100mm wide glass strips, white framed and fixed with aluminium anodised frames etc stainless steel wire cloth of 0.63 mm nominal dia and average aperature 1.4 mm , aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc.and fixed to stone masonry wall complete all as specified complete all as specified and directed.

S&F for solid PVC door frame of size 50mm x 47mm made out of 5mm, printed PVC sheet, edges will be painted to match with printed sheet, reinforced with MS square tube & fixing in opening including hold fast.

S&F for factory made solid panel PVC door shutter 30mm thick (stiles) consisting of frame made out of MS Tubes for top & bottom rails, MS frame shall be covered with heat moulded wooden grain printed PVC sheet and 5mm thick x 15mm wide PVC sheet beading used inside stiles & rails and decorative PVC beading of 10mm x 10m used instead of exposed portion of PVC sheet beading.

S&F for aluminium butt hinges of size 100mm or extruded aluminium alloy with gavanised MS hinge pin anodised type B-21.

S&F for viterous china wash down water closet pan pedastel pattern (EWC) white in colour with and incl plastic water seat and cover white closed pattern with flat bottom and cover and MS chromium plated hinging device incl conection to out going pipe and flushing pipecomplete all as specified.

S&F for PVC flush tank low level cistern 10 ltrs capacity including connection to water supply line and water closed pan including 32mm dia flush pipe all as specified and directed.

S&F for vitreous china wash basin, white flat back of size 550mm x 400mm, excluding tap including bracket all as specified and directed.

S&F for angular stop valves CP fancy type screwed down high pressure with crutch or butterfly handle screwed both ends for pipe or union fixed for 15mm bore.

S&F for bib tap cast copper alloy fancy type chromium plated 15mm bore complete all as directed.

S&F for tubes medium grade 15mm bore galvanised with all fittings fixed complete to walls and ceilings or laid in trenches complete all as specified and directed.

S&F for tubes medium grade 20mm bore galvanised with all fittings fixed complete to walls and ceilings or laid in trenches complete all as specified and directed.

S&F for tublar towel rail of 20mm dia of 60cm in length, D shaped bracket brass chromium plated including brackets all as specified and directed.

S&F for PVC waste pipe 32mm bore for wash hand basin.

S&F cast iron 'P' or 'S' trap for fixing to 100mm dia pipe complete all as specified.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe etc and getting out in soft/loose soil.

Supply, lay and testing medium grade GI Tubing of size 25 mm bore with all fitting such as tee bends union elbow reducer etc laid in trenches/fixed to walls/floors, ceilings all as specified .

M&L for cutting existing steel tubing bore of pipe 25mm for alterations or additions (each cut measured) complete all as directed.

M & L for concealled point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC conduit medium grade of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one light point or one fan point controlled by one, one way switch including 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on MS concealled box for mounting of switch,terminal box for mounting ceiling rose/ holders etc and making good to disturbed surfaces all as specified and directed.

M & L for concealled point wiring with two single core PVC insulated unsheathed 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm (Nominal area) drawn in and including PVC conduit medium grade of required size with all fittings and accessories alongwith one single core green colour PVC insulated 1100 volt grade multi stranded FRLSH Copper conductor cable of size 1.5 sqmm as earth lead and connected to earth dolly for one 5 amps socket point on same board including 3mm thick hylam sheet screwed with 04 nos cadmium coated screws & cup washer on MS concealled box for mounting of switch,terminal box for mounting ceiling rose/ holders etc and making good to disturbed surfaces all as specified and directed.

S&F 5 Amp switch piano type single pole one way all as specified and as directed

S&F socket flush type 6 amps, 5 pin, 230v all as specified and as directed

S&F ceiling rose surface Bakelite three terminal all as specified and as directed

S&F MCB, Single Pole, 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve all as specified and directed. MAKE:- Cat part No - 4085-87 to 4085-95 of Legrand/ABB/Schneider

S&F MCB, Double Pole, 6 to 32 amps, 240 Volts, 10 KA breaking cap, ‘’C” curve incl dismentling taking down unsv one all as specified and directed. MAKE- Cat Part No- 4085-98 to 4085-98 of Legrand or equivalent of Schneider /ABB

S&F MCB distribution board, IP 43 protection, Double door, metal enclosure, SPN, 230 Volts, 8 way incl dismentling taking down unsv one all as specified and directed. MAKE- Cat Part No- 6077 11 of Legrand or equivalent of Schneider/ABB

S&F LED Tube light fitting, 18 watt, CDL, 230 Volts, 4 feet long , complete with all accssories internally pre wired and including connecting up to ceiling rose with 0.5 sqmm twin core copper flexible conductor cable incl LED lamp and mounting casing box 2 nos any type all as specified and directed. Make-CG, Cat Part No LCTL 18 CDL) or equivalemt in Havells/Bajaj/Philips/HPL

S&F LED building security light 15 watt, 230V complete with all accessories and including connecting up to ceiling rose with 0.5 sqmm three core copper flexible conductor cable, One GI medium grade 20mm dia bracket of total length 50 cm and fixed to wall with 2 Nos MS Clamp and fastener incl dismentling taking down unsv fitting any type all as specified and directed. Make-CG, Cat Part No LSTP-15-CDL or equivalent in Bajaj/Philips/HPL/Havells

M & L for Earthing complete with galvanised steel pipe electrode, 40mm bore, medium grade, 3 mtr long buried directly and vertically in ground with top edge at ground level after making bore hole of size not less than 300 mm dia and 3.0 Mtr long using suitable mechanical drilling rig (for drilling near the specified bldg), connected with galvanised steel earthing lead of 4mm dia all as shown in Plate No-2, connected to the earthing test point, concrete pit in PCC 1:3:6 type C-2with RCC precast pit cover slab 400mmx400mmx80mm with handle for lifting made out of 8mm dia MS rod, funnel, wiremesh, 15 mm dia light grade GI tubing for protection of GI wire 4mm dia, charcoal and salt in alternate 150mm thick layers around GI earth pipe, including necessary returning filling in & removal all as specified or indicated in SSR Part-I, including testing to achieve earth resistance value as per IS specification on completion.

Shri Sant Cosntruction

V.R.PRAJAPATI AND CO.

M/S JAYCONSTRUCTION CO