SPL REPAIR TO BLDG NO. P-12/01 TO 08 COMPOUNDER LINE (GOVT MD ACCN) OF MH AND PROVN OF STORE ROOM AND SHED UNDER ZONE-II

Amount

B/R Portion Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L coloured non skid joint free ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

M&L Non- skid joint free coloured ceramic tiles 7 to 8mm thick (square / rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed

M&L for coloured glazed ceramic tiles 450mm X 350mm X 7 to 8mm thick on vertical surfaces such as skirting and dados etc set and jointed in neat cement slurry pointed in coloured cement to match over and incl backing coat 10 mm thick in CM (1:4) complete all as specified and directed

Taking down cement plaster on brick or stone walls incl.raking out joints hacking for key scrubbing down with water complete all as specified and directed

M&L for rendering 15mm thick cement plaster on fair faces of stone masonary or other than fair faces of brickwork in cement mortar 1:4 finished even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L for rendering 15mm thick cement plaster on fair faces of stone masonary or other than fair faces of brickwork in cement mortar 1:6 finished even and smooth w/o using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L rendering 10 mm thick in CM 1:3 as on concerete surface on ceilings finished even and smooth with and incl using recron 3s polypropylene fibre complete all as specified and directed .

M&L for preparing new plastered surfaces of wall and applying two coats of oil bound distemper over and incl a coat of primer over and incl a coat of wall care putty of 3mm thick (avg thickness) applied in two layers including rubbing with suitable sand paper complete all as specified and directed .

M&L for preparing new plastered surfaces of ceiling and applying two coats of oil bound distemper over and incl a coat of primer over and incl a coat of wall care putty of 3mm thick (avg thickness) applied in two layers including rubbing with suitable sand paper complete all as specified and directed .

M&L for preparation of newly plaster surface of wall and applying two coat of exterior emulsion weather proof paint over and including one coat of primer on walls over and incl 3mm thick (avg thickness) applied in two layers including rubbing with suitable sand paper complete all as specified and directed .

M&L 15-16mm thick granite work (table rubbed & polished) (Rajasthan black) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over & incl 15 mm screed thick in CM 1:4 complete all as specified and directed .

M&L for 20mm thick granite (of any colour) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and rounding the edges of granite complete all as specified and directed

M&L 15 mm thick screed bed or bedding layer of cement 1:6, for laying floor finishes etc complete all as specified and directed.

M & L Machine cut kota stone slab flooring 20-25mm thick in steps , floors laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

Rounding to edges of stones slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

S & F 18 mm thick HDHMR (High density high moisture resistant) board of 'Action Tesa' or equivalent one side white laminate and other side decorative as in kitchen cabinets fixed with minifix hardware where ever required including edge band 22 mm wide 0.80 m thick (of REHAU or equivalent)of matching colour on exposed surfaces of board fixed with polymaster adhessive of REHAU make or equivalent including trimming edges of edge band to true line of thicknesss of board by manual trimmer complete all as directed

S & F 8 mm thick HDHMR (High density high moisture resistant) board of 'Action Tesa' or equivalent one side white laminate and other side un decorative as in back of kitchen cabinets.

S & F auto close hinges , stainless steel of grade SS-304 , bright finish fixed complete all as specified (Make : Hettich or equivalent)

S & F stainless steel handles of size 100 mm fancy type of approved make complete all as specified & directed

S & F in repair sinks with drainage board made of stainless steel 1mm thick, 18 guage of Grade SS-304, kitchen or laboratory with plugs, washers and wastes including fixing cantilever brackets and connecting union to pipe, waste pipe, overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

S&F in repairs Vitreous china wash down water closet (EWC) white pedestal pattern complete, including connection to drain pipe and to flushing pipe antisyphonage pipe, (excluding flushing cistern) plastic water closet seat back closed pattern with flat bottom cover and mild steel chromium plated or aluminized hinging device, incl. jet connections etc complete all as spd & directed

S&F in repairs PVC valveless, syphonic action flushing cistern 10 ltr capacity, low level, white, with inlet, ball valve , float and handle including brackets and PVC flush pipe complete all as specified.

Taking down chowkats or frames not exceeding 1.5 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each with shutter (without taking off shutter from the frame) and removing from site complete all as specified and directed.

S & F for Factory made Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as given in SSR Part – II complete all as specified and directed.

S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppy and fixing in the frame at site complete all as per specifications and drawings given in SSR Part – II complete all as specified and directed.

S & F 35mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with sunmica lamination complete all as specified and directed.

S & F 35mm thick second class hardwood factory made glazed and skeleton door shutters open rebated of second class hard wood rail and styles(Hollock), prepared to receive glass/gauge etc divided into square , with plain, chamfered or rounded, mitred and rebated sash bars any numbers , fitted with cut and mitred beads for securing glass/gauge etc. The size of rails & style as specified in SSR Part-I (2009) section 8 and as per IS-1003(Part-I) kiln seasoned as per IS-1141 and chemically pressure treated as per IS-401 complete all as specified and directed. Note :- S & F Glass/gauge shall be measured and paid for separately

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire & average width of aperture 1.40mm & fixed to wodden door shutters and fixed with stainless steel wire staples complete all as specified and directed.

S &F framed work such as door frame, grills, gratings, etc., with ends of bar shoulder and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks with Angle, MS sheet Flat iron & similar work conforming to Fe 290 GDE -E-165 (Ladders, door frames and cooler stand etc) complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

S&F 250mm mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S & F 150mm size SS handles, cast moulded type fixed with screws complete all as specified and directed.

S & F 200mm long SS barrel tower bolt not less than 12 mm dia of extruded sectionas complete all as specified and directed.

S & F 75 mm long door stopper of stainless steel body with two number rubber shoes complete all as specified and directed.

S & F 150mm long MS Helical door spring including roller and roller plate fixed to angle iron chowkats complete all as specified and directed.

S & F in repair pressed steel factory made cupboard shutter with frame of 1.25 mm thick and shutter 1 mm thick PBI sheet with 6 nos, 3.15 mm thick and 100 mm long steel hinges godrej patern locking arrangement incl 12 mm dia vertical rod incl spray painting in factory in wood finish pattern complete all as specified and directed.

S&F in repair 25 mm dia SS drapery rod grade 304 medium weight complete all as specified and directed.

S&F SS -304 grade brackets/ end brackets for holding drapery rod complete all as specified and directed.

S&F SS Finials suitable for 25mm dia SS 304 grade drapery rod as approved complete all as specified and directed.

S&F powder coated any colour (minimum thickness of powder coating 50 micron) anodised aluminium frame for doors/windows/ ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F powder coated any colour (minimum thickness of powder coating 50 micron) anodised aluminium window and ventilator shutters, fixed / sliding type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber packing,locks, anodised alumnium snap beading, screws etc. complete all as specified

S&F 5.5 mm thick frosted/ plain sheet glass,ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm each pane complete all as specified and directed.

S&F aluminium alloy wire cloth 0.45mm nominal dia of wire and average width of operature 1.40mm and fixed with aluminium wire staples complete all as specified and as directed.

Supply and fix 15 micron coloured aluminium anodised grill design No DG-117,10 mm thick including F Sections complete all as specified and directed. Make :- M/s Deco grill / M/s Royal grill or Equivalent

S&F in repair brass cromium brass plated fancy type bib taps 15 mm bore long nose screwed down, screwed for iron pipe or for brass union complete all as specified and directed

S & F in repair PTMT grating doom 100 mm dia with waste hole complete all as specified and directed. Note: Min Weight 25 gms

S&F in repair 15mm dia pillar taps cast copper alloy with capstan head, chromium plated, fancy type, screwed down high pressure with or without lettered hot or cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore stop valves cast copper alloy, fancy type cromium plated, screwed down high pressure with crutch as butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed.

S&F in repair angle valve 15mm dia bore chromium plated cast copper alloy with long shank and cup complete all as specified and directed.

S&F in repair 32mm dia PVC waste pipe having length of 450 mm complete all as specifieid.

S&F in repair 110mm dia PVC (SWR) pipes, single socketed in length with rubber ring joints fixed to wall with and incl suitable SS clamp complete all as specified and as directed.

S&F in repair 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

M&L for concrete bed to drain pipe incl. packing under hanching against the side of pipes, 150 mm bore, in cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) after laying and testing of pipe complete all as specified and directed.

M&L for PCC(1:2:4) type B-1 using 20mm graded stone aggregate as in haunching and bed in manholes and PCC bend for top of manhole brick work etc complete all as specified and directed.

M& L for cutting into existing manholes for connecting in new drain, making good to pipe and rendering, cutting existing benching for and forming branch channel (1/2 or 3/4 section) in PCC 1:2:4 type B-1 using 20 mm graded crushed sone aggregtes) smooth finishing and reforming benching as reqd for 150 mm dia pipe. all as secified and directed.

M&L for providing precast reinforced cement concrete of type B1 (1:2:4) (using 20 mm graded stone aggregate) as in cover slab for manhole etc set in cement mortar (1:4) complete all as specified and directed. Mnote : Reinforecement shall be measured and paid seperately.

S&F in repair 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) bends any radius complete all as specified and as directed.

S&F 125/110 mm dia PVC (SWR) Gully trap setting and jointing with solvent cement complete all as specified and as directed.

S&F in repair vitreous china WHB white flat back size 550 x 400mm with PVC waste pipe, brass chromium plated waste coupling for basins etc with long screw shank and fly nuts flanged and fixing complete all as specified

S&F in repair tubular towel rail, brass chromium plated, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S& F Stainless steel peg stay six complete all as specified and as directed

S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified & as directed.

S&F 110mm dia PVC (SWR) outlet nahani trap/floor trap with grating including jointing with solvent cement complete all as specified and as directed.

S&F Soap dish, vitreous china white, approximated sixe 160 x 160 x 90 mm complete all as specified and as directed.

S & F in repair 15mm bore GI tubing medium grade with all necessary fitting, fixed to wall or concealed or fitted to ceiling or laid under floor incl taking down old one complete all as specified and directed

S & F in repair 20mm bore GI tubing medium grade with all necessary fitting, fixed to wall or concealed or fitted to ceiling or laid under floor incl taking down old one complete all as specified and directed

S&F brass Chromium plated central hole basin mixer 15mm bore for mixing hot & cold water, screwed down with long sunk and fly nutsscrewed for 15mm dia pipe complete with nipple and arms complete all as specified and directed.

S&F in repairs fancy type CP Health faucet 15 mm bore (ISI marked) including extension Pipe of 1 Mtr length complete all as specified and directed.

M&L for preparation of new or previously untreated steel surfaces of any description not otherwise described over 10cm in width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and as directed

S&F in repair corner glass self large 300mmx300mm fixed with chromium plated brass screws complete all as specified and as directed

S & F in repair plate rack of size 750mmx600mmx250mm fabricated out of 0.6mm thick stainless steel sheet and fixed with chromium plated brass screws complete all as specified and directed. fixed in repair

Dismantling loose/cracked concrete completely as in ceilings, chajjas, balconies, roof projections upto double storey buildgs including cleaning existing reinforcement, applying rust remover, removing rusted steel bars, apply bonding agent to hold concrete surface and casting chajjas using RCC 1: 1 1/2: 3 type B1 (using 20 mm graded stone aggregate) to outward slope incl necessary formwork, scaffholding etc complete.

Dismantling/ chipping of unsound weak/ loose & cracked concrete/ cement plaster as in soffits of chajjas, ceillings , roof projections upto double storey buildgs including cleaning existing reinforcement, applying approved rust remover, removing rusted steel bars if necessary, applying rust protection primer, also applying Epoxy resin concrete bonding coat on prepared RCC surfaces as per manufacturers instruction bonding agent to old concrete/ plaster surface and finishing to required thickness with recron fibre mix modified cementitious mortar

M&L Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape requried, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

,---ditto--- all as per item No 80 but 10 mm dia & over complete all as specified and directed .

Dismantling wrought iron or mild steel, including gates work of any description not otherwise provided for complete all as specified and directed.

M & L Steel work in tabular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 complete all as specified and directed.

Dismantling CGI / asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strenght of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws/J hook,L-type crancked hook as specified and directed.

Taking down existing roof treatment complete including PCC and properly clean the surface to remove loose particles with wire brushes and removing the debris out side of MoD Land complete all as specified and directed by Engr-In-Charge

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0,( 1.2.4) using 12.5 mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement measured & paid separately.

Supply only integral water proofing compund complete all as specified and directed.

M&L screed plaster 10mm thick in cement mortar (1:3) on concrete surfaces of roof to receive water proofing treatment finished even and fair complete all as specified.

The surface shall be painted with one coat of polymeric primer @ 0.40 kg per sqm conforming to IS: 3384 and a coat of bitumen grade 30/40 @ 1.20 kg/ Sqm below the layer of APP based polymeric memberance.( 3 mm thick minimum weight not less 150 gms ) and Side over lap shall be 75 mm and ends shall be 100 mm and all over lap and joints insert upto thr ht 150 cm vertical surface imbeded in wall and finifhing in CM 1:3 , embeding membrane into spout pipe , roof down ward facia and shall sealed by torch application with bitumen 30/40 grade, coved filled in PCC (1:2:4) type B-0 of radious 75 mm at roof junction,parapet wall and other vertical surface complete all as specified Applicatiion of polymeric memberance shall be torch application all as per manufacturer instructions. Note ; the work shall be carried out through authorised applicator only.

M&L preparation of APP based polymeric surface and applying two coat of aluminium paint all as specified & as directed.

M & L for 75mm thick PCC 1:3:6 , type C-2 using 40 mm graded stone aggregate as in plinth protection laid in slope in 1:30 in alternative bays not exceeding 3 mtr in length. Exposed surfaces finished even and smooth without using extra cement including raking out joints between panel to panel and panel to wall and plugging the same with bitumen mastic using bitumen and sand mixture in 1:3 complete all as specified and directed .

S&F Complete removal of existing treatment of walls by mechanical means and applying two coat of Exterior acrylic emulsion weather proof paint over a coat of alkali resistant primer on walls complete all as specified.

M & L prepartation of old plastered surfaces, filling depressions with putty and applying two coats of oil bound distemper on walls complete all as directed.

Demolition of cement concrete (unreinforced) in ground floors and paving of any description and removal of same from outside MOD land complete all as specified and as directed by Engineer-in-Charge.

Excavating in post holes (or similar holes) each not exc 0.50 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm, watering, and removing surplus soil to a distance n.exc 50 m and making good surface in soft/ loose soil complete all as specified and as directed.

M&L PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates conforming to Fe410-W(Gde E-250) Quilaty A complete all as specified and directed.

Excavation in trenches n.exc 1.5 mt wide and n.exc 1.5 m in depth, for foundation etc or for shafts, wells, manholes, pier holes etc n.exc 10 Sqm on plan and n.exc 1.5 m in depth and getting out in Soft/loose soil complete all as specified and directed.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specified and as directed.

Removing excavated material to a distance n exc 50 m and deposited where directed at a level n exc 1.5 m above the starting point complete all as specified and as directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) in foundations, filling and mass-concrete complete all as specified and directed.

M & L formwork to sides and soffits of floor or beam, beam haunchings, grider, bressumber, lintels, cantilever, shelves including supports, over hang etc also splay between floor and beams to rough finish surface of concrete flat complete all as specified and directed by Engineer-in-Charge.

M & L for RCC type B1 1:2:4 (using 20mm graded aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed Note: Reinforcement shall be measured and paid seperately.

M&L for brick work with sub-class 'B' bricks (ols size), straight or curved on plan exc 6m mean radius built in In cement mortar 1:6 complete all as specified and directed

M&L for rendering 15mm thick cement plaster on fair faces of brick or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L 15mm thick rendering on brick surfaces of wall in CM 1:4 finished even and smooth without using extra cement including mixing of WPC compound complete all as specified and directed. Note : WPC shall be measured and paid separately.

M&L for complete removal of existing treatment on walls, including cleaning of any mortar drops, fungus efflorescent salts etc and preparation of old plastered surfaces and applying two coats of distemper with distemper oil emulsion white or tinted by mechanical means over a coat of primer over 1mm thick wall care putty to make smooth the undulated surfaces complete all as specified and directed.

M&L hardcore of broken bricks of gauge not exc 63 mm, deposited spread and levelled in layers n exc 15 cm thick watered and rolled /rammed to a true surface complete all as specified and as directed.

M&L for 150mm thick PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in flooring complete all as specified and directed by Engineer-in-Charge.

S&F suspended false ceiling extra microperforation size of 600 x 600 x 12 mm ceiling tiles over and including suspension metal system (MICRO LOOK) designer grid (15 mm grid 8mm return) including necessary hanging system arrangement which is required to be made from existing rafter and purlins of trussed roof of building or RCC roof/ stone slab all as directed by Engineer-in-Charge.

S&F powder coated anodised aluminium section (minimum thickness of powder coating 50 micron) for doors, door partitions including fabrication of frame and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc incl all accessories such as glazing clips, rubber beading for fixing glass panes in frame complete all as specified and directed. Notes : (i) Glass panes will be measured and paid seperately (ii) The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and paid seperately.

M&L for 4mm thick sheet glass, ordinary quality (frosted on one side) and glazing with aluminium beads and rubber gasket in square exc 0.5 sqm in each pane complete all as specified and directed

M & L 100 mm thick plain cement Concrete 1:2:4 type B-0 (using 12.5mm graded aggregate) in floor, finish the surfaces even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for 100mm thick plain cement concrete (1:4:8), type D-2 (using 40mm graded stone aggregate) as in sub base finished even and fair complete all as specified and directed.

M&L machine pressed precast concrete interlocking coloured rubber moulded paver block any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, with grey cement and pigment laid over 25mm thick sand cushion complete all as specified and directed. Note : Sand for cushioning shall be measured and paid seperately.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

E/M portion Taking down carefully surface aluminum /copper point wiring, casing capping /PVC concealed conduit for (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling rose, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade of size not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories concealed in wall/ roof/floor and modular sunken GI metal boxes not less than 1.0mm thick and incl white modular cover plates with frame for mounting modular switches, sockets, fan regulators etc for one light point controlled by one, one way switch complete all as specified and directed.

,---ditto--- all as per item No. 119 here-in-before but for one fan point controlled by one switch and regulator complete all as specified and directed.

,---ditto--- all as per item No. 119 here-in-before but for one bell point controlled by one bell push complete all as specified and directed.

,---ditto--- all as per item No. 119 here-in-before but for one socket outlet 6 amp controlled by one switch on the same board with other switches complete all as specified and directed.

,---ditto--- all as per item No. 119 here-in-before but for one socket outlet 6 amp controlled by one switch on indepdendent board complete all as specified and directed.

M&L for point wiring with 1100 volts grade PVC insulated FRLS multistranded copper conductor cable 4 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and modular sunken GI metal boxes not less than 1.0mm thick and incl white modular mounting cover plates with frame for mounting modular switches, sockets, fan regulators etc for 3 pin 16/20 amps socket outlet point controlled by one switch on independent board complete all as specified and directed.

S&F switch modular 1 way 6 Amps, 230 volts, 1 module complete all as specified and directed.

S&F modular switch 1 way 16 Amps, 230 volts, 1 module complete all as specified and directed.

S&F modular socket 6/16 Amps, 2/3pin combined 2 module AC 230 volts complete all as specified and directed.

S&F modular socket 6 Amps, 2/3 pin combined 2 module AC 230 volts complete all as specified and directed.

S&F modular hum free electronic step fan regulator 120-280 volts of 100 watts capacity (socket type), 2 module including connecting up complete all as specified and directed.

S&F angle holder, insulated polycarbonate body with back plate complete all as specified and directed.

S&F ceiling rose 3 plates polycarbonate body complete all as specified and as directed

S&F modular bell push, 6 Amp, 1 module complete all as specified and directed.

S&F electric door bell, ding dong, AC 240 volts, single pole complete all as specified and directed.

Taking down carefully sub main wiring with PVC casing capping / PVC surface conduit and making good disturbed surfaces complete all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm PVC insulated FRLS multistranded copper conductor cable alongwith one run of 6 Sqmm earth wire as earth continuity conductor (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non mettalic PVC conduit of size 25mm, medium grade, ISI marked ivory colour alongwith accessories of suitable size including making connection as required and making good the disturbed portion complete all as specified and directed. NOTE - Two run of 6 sqmm phase and neutral wire & One run of 6 sqmm earth wire & One run of PVC conduit with accessories shall be measured as One length.

S&F in repair MCBs Distribution board SPN, 8 ways, powder coated, CRCA steel sheet, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 100 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F in repair MCBs Distribution board VTPN 4 ways, powder coated, CRCA steel sheet, suitable for MCCB incomer upto 160amp, degree of protection IP-43, IK09 with reversible double door, 415V, recess mounted having insulated 200 amp tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, blanking plate in unused spaces as required, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'B' curve single pole 6 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'B' curve double pole 10 to 32 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCBs of 'B' curve double pole 40 to 63 Amps having breaking capacity 10 KA, ISI marked including required wiring connections with copper lugs of suitable size provided in MCB DBs complete all as specified and directed.

S&F MCCB four pole, 415 volt, adjustable type, 160amp with breaking capacity 36KA including reqd cable connections with copper lugs of suitable size and testing & commisioning and make goodcomplete all as specified and directed.

S&F in repair LED bulk head light fitting 9/10 watt IP 66 & IK 09 with polycarbonate body with LED driver duly prewired connection with 0.75sqmm PVC insulated & sheathed three core flexible multi stranded copper conductor cable complete all as specified & directed.

S&F LED batten (0.6m) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 900 lumens at a minimum system efficiency of 115 lumen per watt and total power consumption not more than 10 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed.

S&F LED batten (1.2M) made of CRCA sheet housing with a PC glossy diffuser duly prewired connection having a nominal system lumen output of 2000 lumens at a minimum system efficiency of 105 lumen per watt and total power consumption not more than 20 watt including driver. It has a rated system life time of 40000 burning hours at L70 and should have a colour temperature of 6500K, CRI>80, THD<10% and PF>0.95 complete all as specified and directed. Make - Philips Cat ref No. ENDURALED BATTEN "BN 308C LED20S PSU CDL WH, Bajaj cat ref No. BLTRU 20W WH VIVA or Havells Cat No. 600BS20WLED840SPCWH as approved by GE.

S&F in replacement of LED bulb 9 watt complete all as specified and directed.

Dismantling and taking out serviceable single phase energy meter any type and make and refixing the same with and incl meter box, PVC insulated multistranded copper conductor/conduit an testing complete all as specified and directed.

S&F in repair greenline high efficiency LED light luminaire 35 watt complete with drive, pressure die cast aluminium housing, UV stablized polycarbonates cover, inbuilt power unit, IP-65 protection including mounting bracket made of 25mm GI pipe, medium grade ISI marked not less than 1.2m, bend in shape, fix with 02 no clamps, nut, bolt and washers as reqd complete all as specified & directed.

S&F exhaust fan, high speed, steel body 250mm sweep, 1200 RPM, four blade, heavy duty motor, copper wound double ball bearings, grey colour with louver, nuts, bolts and washers and three core 0.75sqmm copper cable connection with protective steel bird guard complete all as specified & directed.

S&F exhaust fan super high speed, sturdy Engg plastic body, 250mm sweep, heavy duty motor, double ball bearings with louver as IS standard and three core 0.75sqmm copper cable connection complete all as specified and directed.

Supply and fixing ceiling fan 1200mm sweep 50 Hz AC 230 votls, 5 star rated in white colour with BLDC fan motor, blades, 0.45 mtr down rod, canopy set, rubber reel including 0.5 Sqmm three core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling and writing MES No. on fan body as required complete all as specified and directed.

M&L for taking out ceiling fan 1200mm sweep 50Hz AC 230 volts and refixing at new location including minor repair and replacement of fan blade or spray painting in existing colour including 0.5sqmm thre core PVC insulated flexible copper conductor multistranded wire from fan motor to ceiling as required complete all as specified and directed.

S & F 20amp, single pole and neutral socket outlet, with 2 pole and earth metal enclosed plug top in powder coated CRCA steel sheet enclosre recess mounted with chained matel cover for socket out let with and incl one single pole B curve MCB 16 Amps complete all as specified and directed.

S&F water heater 25 litre capacity BEE star rating 5 in approved colour, heating element 2.0 KW, adjustable temperature setting knob for temperature setting between 25° C to 75° C and avoid overheating of water, outer tank made of metal, inner tank made of extra thick superior cold rolled steel provided with high density PUF insullation, safety valve, thermostate, NRV etc complete all as specified and directed.

S&F heavy duty stainless steel connection pipe, 15 mm bore 450 mm, suitable for hot and cold water, premier quality, 304 grade stainless steel alongwith copper inner joint, EPM tube with two numbers brass chromium plated nuts at end alongwith double ring sealing washer to prevent leakage complete all as specified and directed.

M&L for earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 15 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) making PCC pit of size 0.3m X 0.3m X 0.3m (inner size) in mix 1:3:6 type C1, 40 mm thick cover reinforced with 6 mm dia M.S bars, 3 nos both ways with lifting hook made out of 8 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, including necessary excavation and earth work and testing on completion to achieve value not more than 2.0 ohm complete all as specified and directed.

S & F 50 mm bore GI tubing light grade with all fitting (ISI marked), fixed to wall/ pole / laid in road crossing etc as reqd complete all as specified and directed.

Supply, laying, jointing, testing & commissioning LT under ground cable PVC insulated, screened PVC bedded, galvanised steel strips or wire armoured, heavy duty with multi stranded aluminium conductor, 1100 volts grade (ISI marked) laid in trenches, ducts, pipes or fixed on poles of size 35 Sqmm 3.5 core complete all as specfied and directed .

M&L for sand cushioning to cable with dry fine sand in trenches 8 cm below the cable and 15 cm above the cable after laying complete all as specified and directed by the Engr-in-Charge Note : punned thickness shall be measured for payment.

M & L bricks for protection cover to UG cable (with old size sub class B bricks) with width equal to length of brick, laid dry and flat abutting each other with gaps between adjecent bricks not exceeding 10mm complete all as specified and directed.

Note:- The contract sum shall be calculated by deducting the amount shown in Credit Schedule attached to this tender, from total amount of Schedule 'A'/BOQ

Satish kumar and company

ANKIT BUILDERS

M/S ROHIT CONSTRUCTION

UNIVERSAL INFRAPROJECT PVT LTD