PROVN OF 01 X SYNTHETIC VOLLEYBALL GROUND ALONGWITH CHAIN LINK FENCE AND LIGHTING AND PROVN OF OVERHEAD SHED ON PATHWY FROM BK NO 1 TO 1C, BK NO 2 TO 2C AND OVER CLP IN FRONT OF BK NO 3 AT NCC OTA KAMPTEE

Amount

M& L for "Asphalt Subbase ; Chemical Treatment of Entire Area to make Land infertile, this will be done by spraying diluted chemical mixed with water, surface dressing not exc 15 cm depth & soling (300mm) the stone aggregate 63 mm to 80 mm and compacting of 8 to 10 tonne roller, Layer of Compacted 6’’(150mm thick) WMM/WBM using Stone aggregate Size 40 MM to 60 MM and Compaction of 8 to 10 tone roller same in One Layer. Cleaning of Sub base (Wire Brushing) before starting Asphalting Layers*Tack/Primer Coat to be applied before BM & AC Layers ((Qty Consumption will have Tack Coat of Up to 3kg Per 10 Sq. Meter). Compacting Layer of Bituminous Layer of Minimum 30 mm Thickness using 12 MM Stone with 80-100/60-70 Grade Bitumen .Bituminous binder percentage would be close to 3.5%. Compacting Layer of AC of Minimum 20 mm Thickness using 6mm Stone with 80-100/60-70 Grade Bitumen. Bituminous binder percentage would be close to 3.5%. Final Layer of Seal Coat using Stone Dust with Bitumen to make the surface appropriate for Synthetic Installation. "

M& L for Edge Wall - Providing and construction of Edge wall around the court to act as a barrier for infill and Asphalt material . Thickness of edge wall - 230mm. Height of Edge wall - 250-350mm (as per site requirement). PCC of Concrete of nominal Mix 1:3:6 up to a compacted thickness of 40mm will be done below the edge wall to give a firm base including excavation and returning filling.

M&L for DRAINAGE - saucer drain of width 6 inches (150mm). The height of drain will be made to match the side of the court along the toe-wall. This drain will channelize water till one corner of the court. From their drainage connection to be provided. MS Grating drain cover made of with 40x40x5mm 'L' angle all around & FLAT strip 25x3mm size in middle, including excavation & returning filling all as specified and directed.

Supply and installation of ITF certified 8 layers acrylic system with thickness up to 3mm. The flooring should be certified by International Tennis Federation (ITF) and Supplying and laying of Acrylic latex synthetic floor in 8 layer where 1 layer of resurface or filler, 5 layer of liquid rubber 2 layers of colour top coats line marking. All complete and as per specification and as per specification and direction of Engineer in charge.

S & F "Fencing on periphery of the court : Vertical Pole of 100x100x3mm MS Square Pipe (Height= 15Feet)Two adjacent poles to be placed 3.50m vertically for each cage which are to be joined using clamp. 2. Horizontal Pole 50x50x2mm MS Square Pipe (Top, Middle, Bottom) 3. Base Plate 200x200x6mm MS Plate with 4 Nos of 12mm Dia Hole (To be fix on Flat slab with 12x200mm Anchor bolt) 4. GI Chain Link fence of size 50x50x4mm 5. Painting on MS Pole - Primer 1 Coat, Enamel 2 Coat- Green Colour 6. Painting on GI Chain link - Enamel 1 Coat- Green Colour 7. Total Structure Height 15 Feet 8. Installation Type- Welding on Poles and GI mesh including excavated post holes with PCC 1:2:4(size 0.60x0.60x0.90m).

S & F VOLLEYBALL POST Exact Size – 2.54 M PIPE SIZE – 100MM Pipe Shape – ROUND Pipe Thickness – 4MM Guage of Steel – 10 to 8 gz Make of MS Pipe – TATA WITH RACHET SYSTEM FOR NET TIGHTENING AND UPPRIGHT SOCKETS FOR HIEGHT ADJUSTMENT MEN / WOMEN epoxy RED POLES & YELLOW UPPRIGHT SOCKETS Paint. Size of Volley Ball Post holes – (600mm x 600mm x 750mm)

Excavation in trenches for laying of cable trench, pole and stay foundation in any type of soft/loose soil not exceeding 1.5 mtr wide and not exceeding 1.50 mtr deep and getting out complete all as specified and as directed.

Excavtion in post holes (or similar holes) each not exc. 0.50 cum in any kind of soil getting out, and removing surplus soil to a distance not exc. 25 mtr and making good of surfaces all as directed.

Returning filling in,including spreading,leveling watering and well ramming in layers not exceeding 25 cms thick complete all as specified and as directed.

Removing excavated materials to a distance not exceeding 50 Mtr & depositing where directed at a level not exceeding 1.5 mtr above the starting point complete all as specified and as directed.

Supply and fix Double wall corrugated High Density Polymer Ethyl(HDPE) pipe for laying of electric cable of size 50 mm outer diameter and 38 mm inner diameter with IS 14930 (part 2) 2001 and 6mm thickness laid in trenches(Including cutting of roads or any others hard surfaces and making good disturbed surfaces) , wall, poles including bends, sockets and other connected accessories complete all as specified and directed. Make : Ketron/tirupati.

Supply and laying in trenches or fixing in walls / poles or drawing through pipe XLPE insulated, screened,PVC bedded, galvanised steel strip or wire armoured,electric power cables ( heavy duty) with aluminium conductor, 1100 volts, grade cross sectional area 6 sq mm,4 core including testing after laid and jointed all as specified and as directed

Supply and fix Steel tubular swaged poles complete with cast iron base plate, finial taper plug, bolts, nuts and screws as specified type 410 SP - 44 (10 meter long) complete with foundation and coping complete all as specified and directed

Supply and fixing LED Flood light minimum 170 W min 120 lm/watt output die cost aluminium housing IP 65 with high power LED as light source complete complete with inbuilt driver.

S&F thermoplastic Junction Box of suitable size complete with front openable hinged cover and locking arrangements with 4 Nos aluminium bas bar 100 Amps, mounted on porcelin insulator including M&L for MCB SPN 10A-1No, fixed on box in Din rail complete with electrical connection fixed to pole with suitable size FI clamp nut bolts and washer complete all as specified and directed.

M & L for Cross arms, bracings, supports, clamps and back plates fabricated from structural steel sections including nuts, bolts, washers, welding, bending cold or hot, drilling holes for bolts, in any shape or size as indicated or directed and inclusive of one primer coat, one under coat and one finishing coat of paint complete all aspecified and directed

Supply, fixing and connecting street light timer switch Astronomical type 32Amp 3P / 230 V having 24 hours x 7 days time setting with 6 years battery back complete with following accessories provisioned in factory made sheet metal box powder coated and fixing arrangement on pole/wall/ or in feeder pillar and dismantling unserviceable switch complete all as specified. :- (a) MCB TP 32 Amps, 415 volts. Make (Leagrand/Havells/Schneider/IndoAsian) -2 No (b) Astronomical timer having 24 hours to 7 days time setting with memory location. -1 No (c) Power contactor ML-3 three pole coil voltage 240 v - 1 No (d) Complete wiring with suitable size of copper wire including necessary thimbles.

Earthing complete with galvanised steet earth plate electrode 600x600x6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr. below the normal ground level connected to galvanised earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 3 connected to earthing test point all as specified and testing on completion including the material and labour for :- (a) Excavation and earth work or drilling hole for electrode in any type of soil (b) PCC pit in cement concrete 1:2:4 TYPE B-1 (.c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric (d) Funnel with watering pipe of GI 20mm nominal bore light grade and copper lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protec-tion pipe 7.50 metre long for protection of earthing lead. (f) Requisite quantity of charcoal and common salt (g) Connection to earthing test point and testing on completion.

M&L PCC 1:3:6 type C2 ( using 40 mm graded aggregates) as in foundation filling and mass concrete complete all as specified and as directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F Pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tube conforming to IS 1161-1979 grade St-240 complete all as specified and directed

M&L Mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-410W Gde E-250 quality B all as specified and directed.

S&F for 11 to 15 mm mild steel screws bolts (machine made) with hexagonal or square heads at one end and screws both ends each screwed end to be fitted with washers and one hexagonal or square nut exc 5cm not exc 10 cm long.

S&F framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plate, riveting, etc n.exc 10 kg each brackets, conforming to Fe-290. Gde E-165 .complete all as specified and directed

Preparation of newly steel surfaces of any description over 10 cm width or girth and applying two coats synthetic enamel paint over a coat of red oxide primer.complete all as specified and directed

M/s B S Jain (BID ID -3154540)

M/s T.S.JOHAR (BID ID -3159591)

M/s Rahul Traders (BID ID -3159725)