B.C.& E.B.C Girl's Residential High School (Cap. 520) at Mahuar Bihta,Patna.

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m ; disposed earth to be levelled and neatly dressed.

Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in :

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches removing the roots and stacking of serviceable material and disposal of unserviceable material:

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

metre

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

Extra for Providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufactures.

Centring and shuttering including strutting, propping etc. and removal of form for :

Metre

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

TMTC-500- 8mm dia .

TMTC-500-10 mm dia.

TMTC-500-12 mm dia.

TMT FE-500-16 mm dia.

TMT FE-500-20 mm dia.

TMT FE-500-25 mm dia.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete

All work upto plinth level

All work from plinth level upto floor V level.

Walls, columns, pillars, posts and struts

Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Providing M-25 grade RCC istead of M20 grade R.C.C

Providing M-35 grade RCC istead of M grade 20 R.C.C

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering, finishing and reinforcement - All work upto plinth level.

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

Half brick masonry with bricks of class designation 100A in foundation and plinth in :

cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia . M.S. bars at every third course of half brick masonry (with FPS brick).

Brick work with bricks of class designation 100A in foundation and plinth in :

cement mortar 1:6 (1 cement : 6 coarse sand)

Extra tor Brick work in superstructure above plinth level upto floor V cum

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing to existing door frames.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) , transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs, and priming coat on unexposed surface etc. complete.

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/ m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-incharge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels, ventilators and partitions etc.,with G.I. beading of appropriate size, made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant, including applying a coat of approved fire resistant primer on G.I. beading etc., complete all as per direction of Engineer-in-charge.

Providing and fixing ISI marked steel glazed door, windows and ventilators of standard rolled steel section & joints mitered and welded with 15x3 mm lugs, 10cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawls plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including applying a priming coat of approved steel primer, but excluding the cost of steel beading and other fittings except necessary hinges or pivots as required.

Providing and fixing pressed steel door frame confirming IS code 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Metre

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up section/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing bright finished brass peg stays 300 mm long of minimum weight 330 gms.to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) :

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plate with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete asper the direction of Engineer-in-charge.

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in-charge

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc.complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern.

Chequerred precast cement concrete tiles 22 mm thick with marbie chips of size 6 mm in footpath & coutyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning tec. Complete on 20 mm thick bed of cement mortar 1:4(1 cement:4 coarse sand)

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc.complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.

Marble work gang saw cut (polished and machine cut) of thickness18mm for wall lining (veneer work) in c ement mortar 1:3 (1 cement:3 coarse sand) including pointing with white coment mortar 1:2(1shite cement:2 marble dust) with an admixture of pigment to match the marble shade:(To be secured to the backing by means of cramps, which shall be paid for separately)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Stone tile work for wall lining upto 10.0m height with special adhesive like araldite or equivalent over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand ) including pointing in-white cement with an admixture of pigment to match the stone shade.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1 st quality conforming to IS : 13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours such as white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622 , of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately)..

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Motar 1:3 (1cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1:1:1 (1 lime : 1 surkhi : 1 coarse sand) / 1:4 (1 cemnt : 4 coarse sand)

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

12 mm cement plaster of mix

15 mm cement plaster on rough side of single or half brick wall of mix.

15mm cement plaster 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

6 mm cement plaster to ceiling of mix.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade to give an even shade.

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed.

Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Neat Cement punning

Finishing walls with Acrylic Smooth exterior paint of required shade :

Extra for plastering walls of height more than 10m form groun level for every add it. Irate height of 3 or part there of

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations :

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1cement :3 coarse sand 6graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size,well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) :

Metre

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos. rounds per 6 meter length, upto 3 m height of wall with existing angle Iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T reinforced barbed wire, stud tied with G.I.staples and G.I clips to retain horizontal , including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer in charge, with reinforced barbed tape (R.B.T) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sp.mm with tape (0.52 mm thick ) and weight 43.478 gm/ metre (cost of M.S. angle , C.C. blocks shall be paid separately)

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia etc. complete.

Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)

Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2)

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular subbase by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.)

for grading- II Material

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rought dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Trees

Shrubs / Creeps

Supplying and fixing C.I. cover without frame for manholes :

Providing M.S. foot rests including fixing in manholes with 20 x 20 10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) as per standard design :

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Bricks (Lead - 1 km kutcha + 7 km pucca)

Coarse Sand (Lead-13 km) from Koilwar.

Stone Chips (Lead-108 km) from Manpur, Gaya

Stone Metal (Lead-220 km) from Manpur, Gaya

Local sand (1 km kutcha + 2 km pucca)

Earth (1 km kutcha + 2 km pucca)

Manure (1 km kutcha + 2 km pucca)

Cement

Bricks

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass ions :

Providing and fixing N.P./C.P. brass/ P.V.C. porcelain shower rose of 15 mm inlet etc. all complete as per specification and direction of Engineer-in-charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing, fixing, testing and commissioning of CP brass swan neck wall mounted sink mixer with wall flange and swinging casted spout complete as required and making good the walls wherever required.

Providing, Fixing air freshner on wall face with necessary rawl plugs and steel screws complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing satin finish stainless steel AISI 316 grade wall mounted coat hooks on door with CP brass wall brackets and CP brass screws complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing, testing and commissioning of adjustable type wash basin with elbow oprated tap for handicap toilet complete with brackets, tracks, waste pipes and other accessories complete including cutting and making good the walls wherever required.

Providing, Fixing, testing and commissioning of raised toilet seat with cover for handicap toilet including providing & fixing CP bolts, nuts, fisher/anchor bolt are required for hangong of WC complete with all accessories. Including cutting & making good the walls & floors wherever required.

Providing, Fixing, testing and commissioning of wall mounted 32 mm dia seamless stainless steel tube coated with nylon non-slip gripping surface hinged Hand Rail 750 x 100 mm complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing grab bar fabricated from 32 mm dia seamless stainless steel tube coated with nylon non-slip gripping surface 600 mm long grab bar in toilets for physically handicapped complete in all respects, including cutting and making good the wall wherever required. For Wash Basins & Water Closet.

Supply, Fixing, testing & commissioning of storage type stainless steel water cooler with inbuilt RO system, including angle valve and flexible connection piping of the following capacity. It shall have C.P brass push cock complete with inlet float valve (with angle valve) with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required.

Providing and fixing soil, waste and vent pipes:

Metre

Metre

Metre

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing single equal plain junction of required degree.

Providing and fixing single unequal plain junction of required degree.

Providing and fixing double equal plain inverted branch of required degree.

Providing and fixing terminal guard.

Providing and fixing collar.

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work :

Metre

Metre

Providing and fixing 125 mm dia, 3 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Metre

Providing & fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete.

Providing and fixing, testing and commissioning of reducing floor drain of 110x63 mm OD as floor drain in cement concrete 1 : 2 : 4 float with floor complete in all respects.

Providing and fixing, testing and commissioning of uPVC multi angle inlet hight riser fittings with 3 or 4 side inlets of 40, 50 & 63 mm size and fixed to uPVC traps with drip seal/m-seal/solvent cement joint complete in all respect.

Providing and fixing cast brass Clean Out plug with suitable insert keys for opening, male threaded joint with G.I. socket lead caulked to soil pipe/waste pipe of C.I. and C.I.(LA) pipe as required complete

100mm dia

Providing, fixing, jointing and testing of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) including injection moulded fittings with bosses like bends, tees, adoptors etc. suitable for rubber ring jointing complete including fixing to walls with clamps and hanging from ceiling to grade on adjustable supports.

40 mm dia

50 mm dia

63 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

metre

metre

metre

metre

metre

metre

metre

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

metre

metre

metre

metre

metre

metre

metre

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

Metre

Metre

Metre

Metre

Metre

Metre

Providing & fixing C.I. double acting air valve of approved quality with bolt, nuts, rubber insertions etc. complete. (The tail piece if required will be paid separately)

Constructing masonry chamber 60x60x75 cms inside, in brick work in cement mortar, 1 : 4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter ,160 mm bottom diameter and 180 mm deep (inside) with chained lid and rcc top slab 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation foundation concrete 1:5:10 mix (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Providing, fixing, testing & commissioning of vertical multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS304 impellers with stainless steel SS304 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900 RPM, suitable for 400/440 volts, 3 phase, 50 Hz AC supply with pressure gauge and with gunmetal isolation cocks, vibration elimination pads etc. complete with base and frame, nuts and bolts and necessary RCC foundations as per requirement as per instructions and pump shall have following duty.

Pumps for Domestic Water Supply (Hydropneumatic)

Providing,fixing, testing & Commissioning of Sump Pumps for lifting water from drainage sumps in plant room

Complete piping 100mm dia common delivery upto 5m as per enclosed tentative layout. (The pipe should be preferably CI LA/heavy duty G.I) -- 1 Set

80mm dia butterfly valve.-- 2 Nos

80 mm dia NRV valve.-- 2 Nos

Necessary cables from pump set to control panel (position of panel marked in enclosed layout in plant room).-- 1 Set

Electrical switch panel having all necessary accessories & safety devices of standard specifications. (Panels with sump pumps near each sump as per site conditions). - 1 No.

Automatic built-up water level controller with necessary length of cable upto control panel.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.

metre

metre

metre

metre

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 mm nominal bore

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Providing, installation, testing and commissioning of stainless steel Y strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

Providing and fixing brass Single acting air valve PN 1.6 of approved quality with bolts, nuts, rubber insertion, tail pieces, tapers etc. if required as complete.

25 mm dia

Providing and fixing motorised butterfly valve with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box etc., complete.

Excavating trenches of required width for pipes cables, etc, including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m.

Metre

Metre

"Extra for excavating trenches for pipes, cables etc.in all kinds of soil for depth exceeding 1.5 m , but not exceeding 3 m.(Rate is over corresponding basic item for depth upto 1.5 meter.)

Metre

Metre

Extra for excavating trenches for pipes, cables, etc.in ordinary/hard rock exceeding 3.0 m in depth but not exceeding 4.5 m.(Rate is over corresponding basic item for depth upto 1.5 Metre.)

Metre

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :

Metre

Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead :

Metre

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

Metre

Metre

Metre

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 20 mm nominal size) all-round S.W. pipes including bed concrete as per standard design.

Metre

Metre

Metre

Providing and laying cement concrete 1:5:10 (1 cement:5 coarse sand:10 graded stone aggregate 20mm nominal size) up to haunches of SW/RCC Pipes including bed concrete as/standard design:

Metre

Metre

Providing and fixing square mouth S.W. gully trap grade 'A' complete with C.I. Grating brick masonary chamber with bricks of class designation 75 and water tight C.I. Cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as/standard design.

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

Metre

Metre

Metre

Metre

Constructing brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C. top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 20 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Extra depth for manholes

Metre

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 0.91m internal dia (at bottom)

Metre

Metre

Constructing brick masonry circular type manhole 1.2 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 1.22 m internal dia (at bottom)beyond 1.68 m to 2.29 m :

Metre

Metre

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m :

Metre

Metre

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on12mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.

Constructing brick masonary road gully chamber 50x45x60cm with bricks of class designation 75 in cement morter 1:4 (1 cement : 4 coarse sand) including 500 x 450mm precast RCC horizontal grating complete as per standard design

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 Metre depth below ground level.

Metre

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Metre

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia,conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.

Metre

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed /plain bevel ended pipe (type A) of required dia, conforming to IS:8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.

Metre

Metre

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Supply,Installation, testing & Commissioning of suitable capacity and type of submersible pump set capable to discharge 20,000 ltrs. of clean filtered water from a 250 mm x 150 mm deep tubewell at a total head of 30 meter, complete with control panel,24 Metres of suitable size G.I. column pipe, bend, gate valve nipple supporting clamp, 30 Metres of neoprene cable etc. complete as required.

SITC of branded submersible pump set of 2 H.P Kirloskar / Crompton or approved make motor control with starter , ISI marked MCB/main switch, ammeter, voltmeter and water level indicator and single phase preventer on return valve Eraction clamp all complete job.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589 / IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp /support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal / Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/ Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/ Stainless Steel cap and chain as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing and fixing of weather proof standard HOSE CABINATE ( 0.6 M x 0.45 M x 0.3 M ) having central opening glazed door with 6 mm thick clear glass including necessary locking arrangement with Allan key, power coating with PO red paint and for housing 2 nos. RRL hose pipe, 1 No branch pipe. as reqd.

Providing & making drainage provision for the riser with 25 mm dia BALL VALVE completed as required

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves,MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

Providing & fixing Fire Extinguishers with wall mounted brackets as per details below:

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

Principal Chamber / Wdern's Chamber Table Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.

BED - Dimension : 2000x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test (Size : 2000 x 900 x 650 mm (H)

Mattress 2" thick (size 75" x 36") Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I

Study Table & Chair : Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish / Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25 x 25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS > Powder Coated

Meeting Table Size : 2.40 m x 1.05m x 750mm Providing & making meeting table of given size made of 35mm thick block board with 1.0mm thick laminate at top and 1-1/2" TW beading on all the sides with proper niche in between beading and laminate edge 25mm thick round laminated pedestal and wooden frame work 75 x 62mm T.W bracket as top support including polishing of wooden frame work and melamine finish all complete as per drawings.

Class room desk - 2 seater with pedestal storage unit (for Class room) & sitting Desk (size : 1050 x 450 x750 (H)) Supply,Fabrication & Installation of class room table top 19 mm thick prelimanated board with 2mm PVC edge banding , supported on MS square Hollow section (size : 40 mm x 40 mm) frame complete with wire manager at table top all fitting & assecories as per drawing & direction of E/I.

Principal Chamber Wadern's Chamber Chair - Seat / Back Assembly : The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA - P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D)

Steel Multifux system for Library - S/F ct site Godrej steel Multifux system of size 7' x 36 " x 18" with 7 nos. shalves of galvanised steel sheet with M.S steel angle frame of size 40x40x8 mm. Complete with supplying and fixing at site with including painting etc. as per direction of E/I

Common room/ Office / Office Table (Size : 1200 x 750 x 760) Supply, Fabrication & Installation of Dining table made of Wood veneer / Powder coated MS frame with 12mm thick glass top complete in all respect. as per drawing and direction of E.I.

Class room/ Teacher table with Chair, office & Lab Table for class room/office (size : 1200 x 900 x 750) Supply, Fabrication & Installation of table made of Powder coated MS frame with 18mm thick prelaminated board top complete in all respect with wire manager lockable drawers etc. all complete as per drawing and direction of E/I

Dining Table- Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy. with the upper frame made of dia. Ø 1.9±0.02cm x 0.2±0.016 thk. and legs made of Ø 1.9±0.02cm x 0.16±0.0128cm thk. M.S. E.R.W tubes and black powder coated (DFT 40-60 microns)

Dining Chair - Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy. with the upper frame made of dia. Ø 1.9±0.02cm x 0.2±0.016 thk. and legs made of Ø 1.9±0.02cm x 0.16±0.0128cm thk. M.S. E.R.W tubes and black powder coated (DFT 40-60 microns)

Common / Indoor game room chair Size : Depth (D) - 57.0 cm Width (W) - 58.0 cm Height (H) - 88.0 cm Seat Height (SH) - 47.5 cm The seat & Back are made up of Cushion covered with rexine. Behind all this is a robust tubular framework that makes the chairs durable.

White Board - Providing and fixing in position magnatic white board on walls including teak wood edge moulding. Complete with all necessery hardware, polish etc as per direction of E/I Size : 8' x 4'

3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I

Computer Table in computer Lab - (size : 900 x 600 x 905 mm) computer Lab Supply and installation of Prelaminated particle board of wood finish on both side and top on hard wood frame with drawer, Cabinet and wire manager complete with all necessary hardware and as per drawing design and direction of E/I.

Computer Chair : Supply and installation of Telemate medium back chair with single point lock tilting mechanism castor and latherlite sheet over PU foam sheet complete on crome base

Point wiring in PVC Conduit , with Modular type switch

Point

Point

Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in sufface / recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Metre

Metre

Metre

Metre

Metre

Metre

Telepone socket outlet, modular type

T.V. socket outlet modular type

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing metal/ PVC box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,“C” curve including connections, painting etc. as required.

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,“C” curve including connections, painting etc. as required.

Supplying and fixing 2 pin, 5 amp ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing Ding-Dong call bell suitable for single phase, 230 volts complete as required.

SPN MCB DB

TPN MCB DB - HORIZONTAL

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, Double Pole, (Single phase and neutral), 240 volts, residual current circuit breaker (RCCB) ,having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

NORMAL PANEL-SCHOOL

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Pilot Lamp

Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body etc. as required.

Supplying and fixing following rating, 2401475 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supply and installaion of regular /standard model A.C. ceiling fan of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minimum 245 cum/min including wiring the down rods of standard length (upto 30cm) with 1.5 sqmm FRLS PVC insulated copper conductor etc as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supplying and fixing 70112 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing recess mounted LED downlighter complete with minimum efficency 100 lm/w in pressure die-cast aluminium houding and integrated electronic driver etc. directly on ceiling including connection with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc. as required.

Supplying and fixing replaceable compact commercial batten suitable for Single TB LED tube complete with 20 watt LED polycarbonate TB tube with built in driver etc. directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supply and fixing following modular switch/socket on the existing modular plate and cover plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/modules, GI box along with modular base and cover plate for modular switches in recess etc as required.- RJ-45 on plate

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Metre

Metre

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Supply and fixing of following size of medium class PVC conduit along with accessories in surface / recessed including cutting the wall and making good the same in case of recessed conduit as rrequired.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

24-port GbE Smart Managed Switch with GbE Uplink Interfaces-24 Ports 10/100/1000Mbps+4 SFP;Port Standards & Functions-IEEE 802.3 10BASE-T Ethernet (twisted-pair copper),IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper),IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper),IEEE 802.3az compliance Auto-negotiation,IEEE 802.3x Flow Control; Full/Half Duplex-Full/half duplex for 10/100 Mbps speeds,Full duplex for Gigabit speed;Media Interface Exchange Auto MDI/MDIX adjustment for all twisted-pair ports;Switching Capacity 56 Gbps; Transmission Method Store-and-forward; MAC Address Table 16,000 entries per device, Maximum 64 bytes packet forwarding rate 41.7 Mpps,Packet Buffer Memory 1.5 MB,Maximum Power Consumption 22.45 watts, Standby Power Consumption 17.84 W/240 V, Acoustics 0 dBA Heat Dissipation 76.55 Btu/hr, Operating Temperature -5 to 50 ˚C (23 to 122 °F), Storage Temperature -20 to 70 ˚C (-4 to 158 °F), Operating Humidity 0% to 95% non-condensing, Storage Humidity 0% to 95% non-condensing, Diagnostic LEDs Link/Activity/Speed (Per 10/100/1000 Mbps port), Certifications CE (LVD) BSMICCC, C-Tick. Netgear / D-link/ Cisco.

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make.

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Supply and fixing Metal/PVC Box of following size (normal size) on surcae or in recessed with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Smart-UPS On-Line, 5.4 kW / 6 kVA with 1 hour Backup12 V 65 AH SMF Battery UPS Toplogy Double Conversion On-Line, Power Rating (VA / Watts) 5400Watts/6000VA, Form Factor Rack/Tower Convertible; Output Power Capacity 5400 Watts/6000 VA, Max Configurable Power 5400Watts/6000VA, Nominal Output Voltage 230V, Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage, Efficiency at Full Load 94.00%, Output Voltage Distortion Less than 3%,Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz,Crest Factor 03:01,Waveform Type Sine Wave, Output Connections (1)*Hard Wire 3-wire (8)*(H N + G) IEC 320 C13(8),Bypass Built-in Bypass, Output Short Circuit Protection Yes,Parallel Redundancy (Option) 1 + 1, Nominal Input Voltage 230V,Input Power Factor>0.98,Input Frequency 40-70Hz,Input Connections Terminal Block, Protection Thermal Circuit Breaker (250VAC/20A), Input voltage range for main operations full load 160 - 285V, Input voltage range for mains operation half load 160-285V, High Voltage withstand Capability 420 VAC, Green Mode Range 210-250 VAC (230 V), Battery Type Mintenance - free sealed Lead-Acid battery with suspended, electrolyte. 12V 65 Ah SMF battery for 60 Min Battery Back up.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

P/F testing joint, made of 20mm x 3mm thick copper Strip.125 mm long with 4 nos of tinned brass bolts nuts chuk nuts and spring washer etc complete as required.

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required (FOR LIFT)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Supply and Installation of outdoor Bullet IR Network Camera 1/2.7" CMOS, ICR, 2592*1944@ 25fps, 5 MP H.265/H.264/MJPEG, Triple streams, DC12V & PoE, Micro SD card slot up to 256 GB, Alarm in/out , Audio 1/1, IP67, 2.7-13.5mm Motorized Varifocal lens, IR anti-reflection window, Built-in bracket, IR range: up to 50m, Digital WDR Range, 3D-DNR for noise reduction, Audio In and Out, Alam in and Out IPv4 network supported, IP67 rated for weather proofing, ONVIF, POE IEEE 802.3af, (UL, FCC, CE, BIS certified). Make-Panasonic/ Bosch/Honeywell

Supply / Installation and Commissioning of Network Video Recorder,H.26+/H.265/H.264/H.264+ video formats,Connectable to the third-party network cameras,Up to Min 32 IP cameras can be connected,Recording at up to Min 8 MP resolution,Supports live view, storage, and playback of the connected camera at up to Min 8 MP resolution,HDMI and VGA independent outputs ,HDMI Video output at up to 4K (3840 × 2160) resolution ,4 SATA interfaces connectable for recording and backup ,2 self-adaptive 10/100/1000 Mbps network interface ,Centralized management of IP cameras,

Supplying and laying of SOLID CABLE, CAT6 UTP, 4PAIR, 23AWG, LSZH CM,BLUE colour through existing conduit /trunk complete as required & as per Direction of Engineer-In-Charge.MAKE : DIGISOL/DIGILINK

Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Aspect Ratio 16:9, Native Resolution 1920 x 1080 (FHD), Brightness 350nit or Higher, Contrast ratio 1100:1 or Higher, Dynamic CR 500,000:1 or Higher, Viewing Angle (H x V) 178 X 178, Orientation Portrait & Landscape, Operation Temperature 0 ⁰C to 40 ⁰C, Safety UL, eUL , EMC FCC Class “A”, IP video input 16 Channel , 1-ch, RCA (2.0 Vp-p, 1KΩ) Two-way audio input, 100Mbps Incoming bandwidth, 80Mbps Outgoing bandwidth, 128 Remote connection, HDMI/VGA output : 1-ch, resolution : 1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 × 720 /60Hz, 1024 × 768 /60Hz, Audio output 1-ch, RCA (Linear, 1kΩ), Live view / Playback resolution :

Hard Disk 4 TB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600mm X 600mm X3mm thick including accessories. a nd providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. ( but without charcoal/ coke and salt ) as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.(For Transformer Neutral)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required (but without pole foundation)

Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector and suitable size foundation bolts with template as required. (but without pole foundation )

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying & embedding of following dia G.I. pipe (medium class) in pole collor / foundation (during casting ) for cable entry including bending the pipe to the required shape complete etc. as required.

Meter

Supplying and fixing post top / gate light (width 250/300 mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( But without lamp)

Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.)

Supplying and fixing of following rating electrical items in the existing cubical panel board/ feeder piller including drilling holes in cubicle panel/ feeder piller making connections etc. as required .

40 Amp to 63 A raiting, TPN MCB, "C" curve, 10KA breaking capacity.

50 mm x 5 mm copper strip (2.30 kg / mtr.)

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

APFC CAPACITOR BANK PANEL -I

4 Nos. 15 KVAR & 2 Nos. 20 KVAR MPP type capacitors with associated 63 Amp TP MCCB's, AC3 duty contactors with each capacitor bank and 6 step relay for automatic and manual operation of capacitors, necessary indication lamps / toggle switch etc and required inter connections complete.

EXTERNAL LIGHTING - FEEDER PILLAR

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Excavation for foundation in soft soil including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil directed within lead of 50 metres.

Providing and laying in position cement concrete 1:2:4 ( 1: cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size )in foundation of pump DG set , feeder pillar and refilling etc. as required

Providing and fixing MV danger notice plate of 200mmX150mm made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc as required.

DISTRIBUTION BOARD (DB):-

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCBilsolator)

Supplying and fixing following rating, 2401475 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

HV CABLE SUPPLY

3 core, 185 sq. mm , 11 KV grade, armoured power H.T. cable , XLPE insulated with PVC sheathed & aluminium conductor

HV CABLE LAYING

Laying one PVC ated PVC XLPE powe r cable of 11 KV grade of following size direct in ground incl uding excavation, sand cushioning, Protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Metre

Supply of following sizes and core of PVC/XLPE insulated PVC sheathed heavy duty, aluminium conductor armoured under ground cable of graded 1.1 KV for working voltage upto 1100 volts conforming to ISI 1554 (Part-I) of 1964 with upto date amendment as detailed below.

Laying of one number insulated and PVC sheathed power cable of 1.1 KV grade of following size direct in ground including excavations, sand cushioning protective covering and refilling the trench etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

Supplying and laying of following size DWC HDPE pipe lSl marked along with all accessories like socket, bend, couplers etc. conforming to lS 14930, Part ll complete with fitting and cutting, jointing etc. In the existing trench, complete as required.

Meter

Meter

11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.

Rubber mat of 16mm thik and 1000mm wide to with stand 15kv dielectric strength as per is 5424. 1969

Shock treatment chart in English and local language duly framed with glass

First aid box complete with all standard first aid materials

Rubber gloves 11 KV grade as per IS 4770-68

Supply installation testing and commissioning of 5.0 LB Noves 1230/FK-5-1-12

Supply fixing testing and commissioning Lienear pneumatic heat Detection

Supply fixing testing and commissioning of Master Control Unit for controlling each system, complete with pressure switches, buzzers and electronic hooter, including all necessary accessories + electrical wiring to make each entier system functional (Make - Firetrex / Tracefire / Safefire).

Supply, installation, testing and commissioning of Silent Type diesel generating set comprising of engine CPCB IV Model 199 BHP @ NTP , 1500 RPM Coupled to 160KVA 3 PHASE 415 VOLT ,50 HZ Alternator mounted on acommon base frame along with other accessories i.e. fuel tank AMF CONTROL PANEL, BATTERY WITH LEADS AND ACOUSTIC ENCLOSURE (CPCB-4 Standard)

Supply, erection, testing and commission of MRL lift Half portion of Glass Door travelling from ground floor to 5 th floor, stopping at 6 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required. (Make:-Thyssen/OTIS/KONE/Schindler/Johnson only)

After Warrenty/ Guarenty

Supply, erection, testing and commission of MRL lift Half portion of Glass Door travelling from ground floor to 5th floor, stopping at 6 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required. (Make:-Thyssen/OTIS/KONE/Schindler/Johnson only)

Supply, erection, testing and commission of MRL lift travelling from ground floor to 3 rd floor, stopping at 4 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required.

After Warrenty/ Guarenty

Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mountedon Aluminium/GI structure of suitable strength with following components complete as required:-a)Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/ IEC61215, IS/IEC61730-Part-1, IS/ IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% attheend of 25 years. b)Power Conditioning Unit (PCU) of 350-800V DC Input voltage range and 400V AC, three phase, 4 wire, 50Hz+/-2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than3% and suitable for ambient temperature from 0 to 50 degreeC. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. (Make-Heron India Pvt ltd / Ojas Solar Energy/ Solar Power Tech) Note:-All Electricals & Mechanical items included.

Item Code. SOR-22

Earth work in excavation over areas (exceeding 30 cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m ; disposed earth to be levelled and neatly dressed.

Earth work in excavation in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, with in a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in :

Excavating, supplying and filling of local earth (including royalty but excluding cairriage cost) by mechanical transport upto a lead of 3km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. If local earth is available at more than 3 km lead the actual lead must be approved by compitent authority. cairraiage of material will be paid seperately and calculated after deducting initial lead.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth : consolidating each deposited layer by ramming and watering lead.

Supplying and filling in plinth with local sand and under floors including, watering, ramming consolidating and dressing complete.

Clearing jungle including uprooting or rank vegetation, grass, brush wood, trees and scaplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.

Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches removing the roots and stacking of serviceable material and disposal of unserviceable material:

Boring, providing and installing bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring, with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. all complete, including removal of excavated earth with all lifts and leads (Length of pile for payment shall be measured upto bottom of pile cap).

metre

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.

Extra for Providing and mixing water proofing material in cement concrete work in the proportion recommended by the manufactures.

Centring and shuttering including strutting, propping etc. and removal of form for :

Metre

Reinforcement for RCC work including straightening. Cutting, bending, placing in position and binding all complete.

TMTC-500- 8mm dia .

TMTC-500-10 mm dia.

TMTC-500-12 mm dia.

TMT FE-500-16 mm dia.

TMT FE-500-20 mm dia.

TMT FE-500-25 mm dia.

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana /Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate /retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete

All work upto plinth level

All work from plinth level upto floor V level.

Walls, columns, pillars, posts and struts

Beams, plinth beams, girder, bressumers, cantilevers, Suspended floors, lintels, roofs and staircase including spiral staircase, shelves etc.

Providing M-25 grade RCC istead of M20 grade R.C.C

Providing M-35 grade RCC istead of M grade 20 R.C.C

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering, finishing and reinforcement - All work upto plinth level.

Brick work with fly ash bricks as per IS 12894 (2002) & IS 3495 in foundations and plinth in :

Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work

Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work

Half brick masonry with bricks of class designation 100A in foundation and plinth in :

cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for providing and placing in position 2 Nos. 6mm dia . M.S. bars at every third course of half brick masonry (with FPS brick).

Brick work with bricks of class designation 100A in foundation and plinth in :

cement mortar 1:6 (1 cement : 6 coarse sand)

Extra tor Brick work in superstructure above plinth level upto floor V cum

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type,core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing to existing door frames.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos. of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer-in-Charge.

Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) , transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete:

Providing and fixing aluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (overall area of door shutter to be measured)

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs, and priming coat on unexposed surface etc. complete.

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/ m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-incharge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels, ventilators and partitions etc.,with G.I. beading of appropriate size, made out of 20 SWG G.I.sheet (zinc coating not less than 120 gm/m2), fire resistant sealant, including applying a coat of approved fire resistant primer on G.I. beading etc., complete all as per direction of Engineer-in-charge.

Providing and fixing ISI marked steel glazed door, windows and ventilators of standard rolled steel section & joints mitered and welded with 15x3 mm lugs, 10cm long with steel lugs embedded in cement concrete blocks 15x10x10 cm of 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) or with wooden plugs and screws or rawls plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing of glass panes with glazing clips and special metal sash putty of approved make complete including applying a priming coat of approved steel primer, but excluding the cost of steel beading and other fittings except necessary hinges or pivots as required.

Providing and fixing pressed steel door frame confirming IS code 4351 manufactured from commercial mild steel sheet of 1.25 mm thickness including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50 x 25 mm or base ties of 1.25mm pressed mild steel welded or rigidly fixed together by mechanical means, adjustable lugs with split end tail to each jamb including steel butt hinges 2.5 mm thick with mortar guards, lock strike-plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineer-in-Charge.

Metre

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and fixing circular/hexagonal cast iron or M.S sheet box for ceiling fan clamp 140 mm internal dia, 73 mm height, 5 mm thick rim bottom and top lids, 1.5 mm thick M.S sheet with its top surface hacked for proper bonding top lid shall be screwed into the cast iron box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamps shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Steel work welded in built up section/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.

Providing and fixing hand rail by welding etc. to steel ladder railings & staircases railing including applying a priming coat of approved steel primer

Providing and fixing bright finished brass peg stays 300 mm long of minimum weight 330 gms.to side hung steel windows with necessary welding and machine screws etc. complete.

Providing and fixing in position collapsible steel shutters with vertical channes 20x10x2 mm and braced with flat iron diagonals 20x5 mm size with top and bottom rail of T-tron 40x40x6 mm with 40 mm dia steel pulleys complete with bots.nuts locking arrangement stoppers handies including applying a priming coat of approved steel primer.

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3mm MS gusset plates at the junction and corners.all necessary fittings completejncluding applying a priming coat of approved steel primer.

Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / aneling,C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item) :

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors,embedding in floors as required and making good the same matching to the existing floor finishing and cover plate with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete asper the direction of Engineer-in-charge.

Providing and fixing aluminium round shape handle of outer dia 100mm with SS screws etc. complete as per direction of Engineer in-charge

Providing and fixing 100mm brass locks (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.

Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of fine sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with jamuna sand and cutting of paver blocks as per required size and pattern,finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc.complete as per manufacturer’s specifications & direction of Engineer-in-Charge. 60mm thick C.C.paver block of M-35 grade with approved colour, design & pattern.

Chequerred precast cement concrete tiles 22 mm thick with marbie chips of size 6 mm in footpath & coutyard jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and cleaning tec. Complete on 20 mm thick bed of cement mortar 1:4(1 cement:4 coarse sand)

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.

Cement concrete flooring 1:2:4(1 cement:2 coarse:sand:4 graded stone agregate) finished with a floating coat of neat cement including cement slurry, etc. but excluding the cost of nosing of steps etc.complete.

Cement plaster skirting (upto 30 cm hieght) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement.

Marble work gang saw cut (polished and machine cut) of thickness18mm for wall lining (veneer work) in c ement mortar 1:3 (1 cement:3 coarse sand) including pointing with white coment mortar 1:2(1shite cement:2 marble dust) with an admixture of pigment to match the marble shade:(To be secured to the backing by means of cramps, which shall be paid for separately)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Stone tile work for wall lining upto 10.0m height with special adhesive like araldite or equivalent over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand ) including pointing in-white cement with an admixture of pigment to match the stone shade.

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of ist quality conforming to IS : 15622 of approved make in colours such as white , Ivory , Grey , Fume Red , Brown , laid on 20 mm thick Cement motar 1:4 (1 cement: 4 coarse sand ) including pointing the joints with white cement and matching pigment etc., complete

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturer) of 1 st quality conforming to IS : 13755 of NITCO , ORIENT , SOMANY , KAJARIA or equivalent make in colours such as white , Ivory , Grey , Fume , Red , Brown , laid on 20 mm thick cement motar 1:4 (1 cement: 4 Coarse sand) including grouting the joints with white cement and matching pigments etc, complete.

Providing and laying Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.08% and conforming to IS:15622 , of approved brand & manufacturer, in all colours and shade, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS : 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately)..

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 (Thickness to be specified by the manufacture) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer -in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Motar 1:3 (1cement : 3 coarse sand ) and jointing with grey cement slurry @ 3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrifed floor tiles in different sizes {thickness to be specified by the manufactruer) with water absorption's less than 0.08 % and conforming to IS : 15622 of approved make in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand ) including grouting the joint with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete with base of 1:1:1 (1 lime : 1 surkhi : 1 coarse sand) / 1:4 (1 cemnt : 4 coarse sand)

Kota stone slabs 25 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Extra for pre finished nosing in treads of steps of Kota stone / sand stone slab.

Extra for Kota stone / sand stone in treads of steps and risers using single up to 1.05 metre.length

12 mm cement plaster of mix

15 mm cement plaster on rough side of single or half brick wall of mix.

15mm cement plaster 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall

6 mm cement plaster to ceiling of mix.

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

Applying one coat of cement primer of approved brand and manufacture on wall surface :

Finishing walls with water proofing cement paint of approved brand and manufacture and required shade to give an even shade.

Applying priming coat:

Painting with synthetic enamel paint of approved brand and manufacture to give an even shed.

Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Neat Cement punning

Finishing walls with Acrylic Smooth exterior paint of required shade :

Extra for plastering walls of height more than 10m form groun level for every add it. Irate height of 3 or part there of

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed protions of W.C. kitchen and the like consisting of :

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations :

Making plinth protection 50 mm thick of cement concrete 1:3:6 (1cement :3 coarse sand 6graded stone aggregate 20 mm nominal size) over 75 mm thick bed of dry brick ballast 40 mm nominal size,well rammed and consolidated and grouted with fine sand, including finishing the top smooth.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (including the cost of chemical emulsion) :

Metre

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length (total length 90 m), having 50 nos. rounds per 6 meter length, upto 3 m height of wall with existing angle Iron 'Y' shaped placed 2.4 m or 3.00 m apart and with 9 horizontal R.B.T reinforced barbed wire, stud tied with G.I.staples and G.I clips to retain horizontal , including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer in charge, with reinforced barbed tape (R.B.T) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sp.mm with tape (0.52 mm thick ) and weight 43.478 gm/ metre (cost of M.S. angle , C.C. blocks shall be paid separately)

Supplying at site Angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia etc. complete.

Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)

Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2)

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular subbase by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401.)

for grading- II Material

Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.

Trenching in ordinary soil upto a depth of 60 cm including removal and stacking of serviceable materials and then disposing of by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge of / and manure before and after flooring trench with water (excluding cost of imported earth, sludge or manure)

Supplying and stacking of good earth at site including royalty but excluding carriage (earth measured in stacks will be reduced by 20 % for payment)

Supplying and stacking at site dump manure from approved source, excluding carriage (manure measured in stacks will be reduced by 8% for payment)

Mixing earth and sludge or manure in proportion specified or directed.

Spreading of sludge, dump manutre or/and good earth in required thickness (Cost of sludge, dump manure or/and good earth to be paid separately)

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm removing all weeds and other growth with roots by forking repeatedly, breaking clods, rought dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts.

Grassing with 'Doob' grass including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free form weeds and fit for moving including supplying good earth if needed.

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20 % 1 part of stacked volume of manure after reduction by 8 % ) flooding with water, dressing including removal of rubbish and surplus earth, if any with all leads and lifts (cost of manure sludge or extra good earth if needed to be paid for separately)

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8 :1 (8 parts of stacked volume of earth after reduction by 8% ) flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and levelling as directed, within a lead of 50 m lift upto 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Plantation of trees & Shrubs/ creeps.

Trees

Shrubs / Creeps

Supplying and fixing C.I. cover without frame for manholes :

Providing M.S. foot rests including fixing in manholes with 20 x 20 10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size ) as per standard design :

Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Bricks (Lead - 1 km kutcha + 7 km pucca)

Coarse Sand (Lead-13 km) from Koilwar.

Stone Chips (Lead-108 km) from Manpur, Gaya

Stone Metal (Lead-220 km) from Manpur, Gaya

Local sand (1 km kutcha + 2 km pucca)

Earth (1 km kutcha + 2 km pucca)

Manure (1 km kutcha + 2 km pucca)

Cement

Bricks

Providing and fixing white vitreous china water closet squatting pan (Indian type WC pan) with 100mm sand cast Iron P or S Trap, 10 litre low level PVC flushing cistern (of approved make) with fittings CI/MS brackets, 32 mm diameter flush pipe with fittings and clamps, over flow arrangement with specials and mosquito proof coupling of approved municipal design including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required.

Providing and fixing wash basin with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

White Vitreous China Wash basin size 550x400 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing 600 x 450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers comelete.

Providing and fixing toilet paper holder.

Providing and fixing PTMT Bottle Trap for Wash basin and sink.

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour, weighing not less than 88 gms.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone finished smooth.aggregate 6 mm nominal size) as per direction of Engineer-in-Charge.

Providing and fixing uplasticised PVC connection pipe with brass ions :

Providing and fixing N.P./C.P. brass/ P.V.C. porcelain shower rose of 15 mm inlet etc. all complete as per specification and direction of Engineer-in-charge.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in -charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing, fixing, testing and commissioning of CP brass swan neck wall mounted sink mixer with wall flange and swinging casted spout complete as required and making good the walls wherever required.

Providing, Fixing air freshner on wall face with necessary rawl plugs and steel screws complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing satin finish stainless steel AISI 316 grade wall mounted coat hooks on door with CP brass wall brackets and CP brass screws complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing, testing and commissioning of adjustable type wash basin with elbow oprated tap for handicap toilet complete with brackets, tracks, waste pipes and other accessories complete including cutting and making good the walls wherever required.

Providing, Fixing, testing and commissioning of raised toilet seat with cover for handicap toilet including providing & fixing CP bolts, nuts, fisher/anchor bolt are required for hangong of WC complete with all accessories. Including cutting & making good the walls & floors wherever required.

Providing, Fixing, testing and commissioning of wall mounted 32 mm dia seamless stainless steel tube coated with nylon non-slip gripping surface hinged Hand Rail 750 x 100 mm complete in all respects, including cutting and making good the wall wherever required.

Providing, Fixing grab bar fabricated from 32 mm dia seamless stainless steel tube coated with nylon non-slip gripping surface 600 mm long grab bar in toilets for physically handicapped complete in all respects, including cutting and making good the wall wherever required. For Wash Basins & Water Closet.

Supply, Fixing, testing & commissioning of storage type stainless steel water cooler with inbuilt RO system, including angle valve and flexible connection piping of the following capacity. It shall have C.P brass push cock complete with inlet float valve (with angle valve) with all plumbing and electrical accessories, inlet, outlet, overflow and PVC drain out connection to F.D complete as required.

Providing and fixing soil, waste and vent pipes:

Metre

Metre

Metre

Providing and fixing in position 25mm diameter mosquito proof coupling of approved municipal design

Providing and fixing M.S. holder bat clamps of approved design to sand cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10 x 10 x 10 cm of 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) including cost of cutting holes and making good the walls etc.

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing plain bend of required degree.

Providing and fixing single equal plain junction of required degree with acesses door, insersion rubber washer 3mm thick, bolts and nuts complete.

Providing and fixing single equal plain junction of required degree.

Providing and fixing single unequal plain junction of required degree.

Providing and fixing double equal plain inverted branch of required degree.

Providing and fixing terminal guard.

Providing and fixing collar.

Providing lead caulked joints to sand cast iron / centrifugallly cast (spun) iron pipes and fittings of diametre:

Providing and fixing M.S stays and clamps for sand cast iron/centrifugally cast (spun) iron pipes of diametre.

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors.

Painting sand cast iron/ centrifugally cast (spun) iron soil, waste vent pipes and fittings with two coats of synthetic enamel paint of any colour such as chocolate grey, or buff etc. over a coat of primer (of approved quality) for new work :

Metre

Metre

Providing and fixing 125 mm dia, 3 mm thick Stainless steel grating with frame for floor traps or drains of required pattern including cutting and making good the floors complete.

Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.

Metre

Metre

Providing & fixing on wall face unplasticised PVC moulded fittings/accessories for unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A, including jointing with seal ring conforming to IS:5382, leaving 10 mm gap for thermal expansion.

Providing and fixing unplasticised -PVC pipe clip of approved design to unplasticised PVC rain water pipe by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing on cement mortar(1:4) 1 cement: 4corsa sand and making good the wall etc complete.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement:2 coarse sand:4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 mx1 mx400 micron, finished 12 mm cement plaster 1:3 (1 cement:3 coarse sand) and a coat of neat cement rounding the edges and making and finishing the outlet complete.

Providing and fixing, testing and commissioning of reducing floor drain of 110x63 mm OD as floor drain in cement concrete 1 : 2 : 4 float with floor complete in all respects.

Providing and fixing, testing and commissioning of uPVC multi angle inlet hight riser fittings with 3 or 4 side inlets of 40, 50 & 63 mm size and fixed to uPVC traps with drip seal/m-seal/solvent cement joint complete in all respect.

Providing and fixing cast brass Clean Out plug with suitable insert keys for opening, male threaded joint with G.I. socket lead caulked to soil pipe/waste pipe of C.I. and C.I.(LA) pipe as required complete

100mm dia

Providing, fixing, jointing and testing of uPVC pipes conforming to IS 4985 class III (6 kg/cm2) including injection moulded fittings with bosses like bends, tees, adoptors etc. suitable for rubber ring jointing complete including fixing to walls with clamps and hanging from ceiling to grade on adjustable supports.

40 mm dia

50 mm dia

63 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc.

metre

metre

metre

metre

metre

metre

metre

Painting G.I. pipes and fittings with two coats of anti-corrosive bitumastic paint of approved quality :

metre

metre

metre

metre

metre

metre

metre

Providing and filling sand of grading zone V or coarser grade, allround the G.I. pipes in external work :

Metre

Metre

Metre

Metre

Metre

Metre

Providing & fixing C.I. double acting air valve of approved quality with bolt, nuts, rubber insertions etc. complete. (The tail piece if required will be paid separately)

Constructing masonry chamber 60x60x75 cms inside, in brick work in cement mortar, 1 : 4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter ,160 mm bottom diameter and 180 mm deep (inside) with chained lid and rcc top slab 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation foundation concrete 1:5:10 mix (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

Providing, fixing, testing & commissioning of vertical multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS304 impellers with stainless steel SS304 shaft as per IEC standards and GJL250 cast iron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900 RPM, suitable for 400/440 volts, 3 phase, 50 Hz AC supply with pressure gauge and with gunmetal isolation cocks, vibration elimination pads etc. complete with base and frame, nuts and bolts and necessary RCC foundations as per requirement as per instructions and pump shall have following duty.

Pumps for Domestic Water Supply (Hydropneumatic)

Providing,fixing, testing & Commissioning of Sump Pumps for lifting water from drainage sumps in plant room

Complete piping 100mm dia common delivery upto 5m as per enclosed tentative layout. (The pipe should be preferably CI LA/heavy duty G.I) -- 1 Set

80mm dia butterfly valve.-- 2 Nos

80 mm dia NRV valve.-- 2 Nos

Necessary cables from pump set to control panel (position of panel marked in enclosed layout in plant room).-- 1 Set

Electrical switch panel having all necessary accessories & safety devices of standard specifications. (Panels with sump pumps near each sump as per site conditions). - 1 No.

Automatic built-up water level controller with necessary length of cable upto control panel.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

metre

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot and cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in charge.

metre

metre

metre

metre

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

20 mm nominal bore

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

Providing, installation, testing and commissioning of stainless steel Y strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.

Providing and fixing brass Single acting air valve PN 1.6 of approved quality with bolts, nuts, rubber insertion, tail pieces, tapers etc. if required as complete.

25 mm dia

Providing and fixing motorised butterfly valve with float type sensors suitable for 240 volts with working pressure rating of not less than 5 kg/cm2 with control panel and sensors to open valve when water level is low in tanks and to close when water level is high in water tanks including necessary cables, conduits, upto junction box etc., complete.

Excavating trenches of required width for pipes cables, etc, including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil , and then returning the soil as required , in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed , within a lead of 50 m.

Metre

Metre

"Extra for excavating trenches for pipes, cables etc.in all kinds of soil for depth exceeding 1.5 m , but not exceeding 3 m.(Rate is over corresponding basic item for depth upto 1.5 meter.)

Metre

Metre

Extra for excavating trenches for pipes, cables, etc.in ordinary/hard rock exceeding 3.0 m in depth but not exceeding 4.5 m.(Rate is over corresponding basic item for depth upto 1.5 Metre.)

Metre

Providing and laying S&S centrifugally cast (spun) iron pipes (Class LA) conforming to IS - 1536 :

Metre

Providing lead caulked joints to spun iron or C.I. pipes and specials, including testing of joints but excluding the cost of pig lead :

Metre

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.

Metre

Metre

Metre

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 20 mm nominal size) all-round S.W. pipes including bed concrete as per standard design.

Metre

Metre

Metre

Providing and laying cement concrete 1:5:10 (1 cement:5 coarse sand:10 graded stone aggregate 20mm nominal size) up to haunches of SW/RCC Pipes including bed concrete as/standard design:

Metre

Metre

Providing and fixing square mouth S.W. gully trap grade 'A' complete with C.I. Grating brick masonary chamber with bricks of class designation 75 and water tight C.I. Cover with frame of 300x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as/standard design.

Providing, laying Non pressure NP2 class (light duty) RCC Pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing and jointing etc complete.

Metre

Metre

Metre

Metre

Constructing brick masonry manhole with 75 class designation bricks in cement mortar 1:4 (1 cement: 4 coarse sand) R.C.C. top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement: 4 coarse sand: 8 graded stone aggregate 20 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Extra depth for manholes

Metre

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 0.91m internal dia (at bottom)

Metre

Metre

Constructing brick masonry circular type manhole 1.2 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement :4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 1.22 m internal dia (at bottom)beyond 1.68 m to 2.29 m :

Metre

Metre

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

Extra depth for circular type manhole 1.52 m internal dia (at bottom) beyond 2.30 m :

Metre

Metre

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on12mm dia steel bar conforming to IS :1786 having minimum cross section as 23mm x 25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protrude legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.

Constructing brick masonary road gully chamber 50x45x60cm with bricks of class designation 75 in cement morter 1:4 (1 cement : 4 coarse sand) including 500 x 450mm precast RCC horizontal grating complete as per standard design

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 Metre depth below ground level.

Metre

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Metre

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/ plain ended casing pipes of required dia,conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.

Metre

Metre

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed /plain bevel ended pipe (type A) of required dia, conforming to IS:8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.

Metre

Metre

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality

Supply,Installation, testing & Commissioning of suitable capacity and type of submersible pump set capable to discharge 20,000 ltrs. of clean filtered water from a 250 mm x 150 mm deep tubewell at a total head of 30 meter, complete with control panel,24 Metres of suitable size G.I. column pipe, bend, gate valve nipple supporting clamp, 30 Metres of neoprene cable etc. complete as required.

SITC of branded submersible pump set of 2 H.P Kirloskar / Crompton or approved make motor control with starter , ISI marked MCB/main switch, ammeter, voltmeter and water level indicator and single phase preventer on return valve Eraction clamp all complete job.

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589 / IS:1239 including Welding, fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp /support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal / Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/ Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/ Stainless Steel cap and chain as required :

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following asrequired.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

Providing and fixing of weather proof standard HOSE CABINATE ( 0.6 M x 0.45 M x 0.3 M ) having central opening glazed door with 6 mm thick clear glass including necessary locking arrangement with Allan key, power coating with PO red paint and for housing 2 nos. RRL hose pipe, 1 No branch pipe. as reqd.

Providing & making drainage provision for the riser with 25 mm dia BALL VALVE completed as required

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases,strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves,MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :

Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size

Providing & fixing Fire Extinguishers with wall mounted brackets as per details below:

ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect

CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.

Principal Chamber / Wdern's Chamber Table Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.

BED - Dimension : 2000x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test (Size : 2000 x 900 x 650 mm (H)

Mattress 2" thick (size 75" x 36") Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I

Study Table & Chair : Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish / Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25 x 25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS > Powder Coated

Meeting Table Size : 2.40 m x 1.05m x 750mm Providing & making meeting table of given size made of 35mm thick block board with 1.0mm thick laminate at top and 1-1/2" TW beading on all the sides with proper niche in between beading and laminate edge 25mm thick round laminated pedestal and wooden frame work 75 x 62mm T.W bracket as top support including polishing of wooden frame work and melamine finish all complete as per drawings.

Class room desk - 2 seater with pedestal storage unit (for Class room) & sitting Desk (size : 1050 x 450 x750 (H)) Supply,Fabrication & Installation of class room table top 19 mm thick prelimanated board with 2mm PVC edge banding , supported on MS square Hollow section (size : 40 mm x 40 mm) frame complete with wire manager at table top all fitting & assecories as per drawing & direction of E/I.

Principal Chamber Wadern's Chamber Chair - Seat / Back Assembly : The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA - P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D)

Steel Multifux system for Library - S/F ct site Godrej steel Multifux system of size 7' x 36 " x 18" with 7 nos. shalves of galvanised steel sheet with M.S steel angle frame of size 40x40x8 mm. Complete with supplying and fixing at site with including painting etc. as per direction of E/I

Common room/ Office / Office Table (Size : 1200 x 750 x 760) Supply, Fabrication & Installation of Dining table made of Wood veneer / Powder coated MS frame with 12mm thick glass top complete in all respect. as per drawing and direction of E.I.

Class room/ Teacher table with Chair, office & Lab Table for class room/office (size : 1200 x 900 x 750) Supply, Fabrication & Installation of table made of Powder coated MS frame with 18mm thick prelaminated board top complete in all respect with wire manager lockable drawers etc. all complete as per drawing and direction of E/I

Dining Table- Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy. with the upper frame made of dia. Ø 1.9±0.02cm x 0.2±0.016 thk. and legs made of Ø 1.9±0.02cm x 0.16±0.0128cm thk. M.S. E.R.W tubes and black powder coated (DFT 40-60 microns)

Dining Chair - Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy. with the upper frame made of dia. Ø 1.9±0.02cm x 0.2±0.016 thk. and legs made of Ø 1.9±0.02cm x 0.16±0.0128cm thk. M.S. E.R.W tubes and black powder coated (DFT 40-60 microns)

Common / Indoor game room chair Size : Depth (D) - 57.0 cm Width (W) - 58.0 cm Height (H) - 88.0 cm Seat Height (SH) - 47.5 cm The seat & Back are made up of Cushion covered with rexine. Behind all this is a robust tubular framework that makes the chairs durable.

White Board - Providing and fixing in position magnatic white board on walls including teak wood edge moulding. Complete with all necessery hardware, polish etc as per direction of E/I Size : 8' x 4'

3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I

Computer Table in computer Lab - (size : 900 x 600 x 905 mm) computer Lab Supply and installation of Prelaminated particle board of wood finish on both side and top on hard wood frame with drawer, Cabinet and wire manager complete with all necessary hardware and as per drawing design and direction of E/I.

Computer Chair : Supply and installation of Telemate medium back chair with single point lock tilting mechanism castor and latherlite sheet over PU foam sheet complete on crome base

Point wiring in PVC Conduit , with Modular type switch

Point

Point

Wiring for twin control light point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box etc as required.

Wiring for light/ power plug with 2 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit along with 1 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4 X 4 sq. mm FRLS PVC insulated copper conductor single core cable in sufface / recessed medium class PVC conduit along with 2 Nos 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.

Metre

Metre

Metre

Metre

Metre

Metre

Telepone socket outlet, modular type

T.V. socket outlet modular type

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed PVC conduit as required.

Supplying and fixing metal/ PVC box of following sizes (nominal size) on surface or in recess with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate/,switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 Nos. 3 pin 5/6 A modular socket outlet and 2 Nos. 5/ 6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,“C” curve including connections, painting etc. as required.

Supplying & fixing suitable size GI box with modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB,“C” curve including connections, painting etc. as required.

Supplying and fixing 2 pin, 5 amp ceiling rose on the existing junction box / wooden block including connection etc as required.

Supplying and fixing Ding-Dong call bell suitable for single phase, 230 volts complete as required.

SPN MCB DB

TPN MCB DB - HORIZONTAL

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating, Double Pole, (Single phase and neutral), 240 volts, residual current circuit breaker (RCCB) ,having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

NORMAL PANEL-SCHOOL

Supply and fixing of fabricated Electrical control panel of cubical construction, floor/wall mounted type, fabricated out of 16 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator and complete in all respect etc and panel manufactures must be approved by CPRI. (But without RYB inicator, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears etc.)

Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Pilot Lamp

Providing and fixing following capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty, complete with all accessories including connections, earthing the body etc. as required.

Supplying and fixing following rating, 2401475 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supptying and fixing following rating, 24Al4L5 volts, "C" curve, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required'

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

Supply and installaion of regular /standard model A.C. ceiling fan of 1400 mm sweep with service value (CM/MM) minimum 4.10, Air delivery minimum 245 cum/min including wiring the down rods of standard length (upto 30cm) with 1.5 sqmm FRLS PVC insulated copper conductor etc as required.

Supply and installation of following sweep/ sizes metallic blade, heavy duty, single phase, 230 V A.C. Exhaust Fan in existing opening including making good the damage, connection, testing and commissioning etc as required.

Supplying and fixing 70112 watt LED type Bulk-head luminaire with minimum efficacy 100 lm/w in comprising of pressure die cast housing, acrylic diffuser,lP 65 protection and complete u.,ith integrated electronic driver etc directly on wall/ceiling including connections with 1.5 sq. mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing recess mounted LED downlighter complete with minimum efficency 100 lm/w in pressure die-cast aluminium houding and integrated electronic driver etc. directly on ceiling including connection with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc. as required.

Supplying and fixing replaceable compact commercial batten suitable for Single TB LED tube complete with 20 watt LED polycarbonate TB tube with built in driver etc. directly on wall/ ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor etc. as required.

Supplying and fixing surface mounted following types LED downlighter with minimum efficacy 100 Im/w in pressure die-cast aluminium housing and integrated electronic driver etc directly on ceiling including connections with 1.5 sq.mm FRLS PVC insulated copper conductor cable etc as required.

Supplying and fixing of following types lamp in the existing electrical fitting/ fixtures etc. as required.

Supplying and fixing batten/ angle holder including connection etc. as required.

Supply and fixing following modular switch/socket on the existing modular plate and cover plate & switch box including connections but excluding modular plate etc. as required.

Supplying and fixing following size/modules, GI box along with modular base and cover plate for modular switches in recess etc as required.- RJ-45 on plate

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Metre

Metre

Supplying and drawing of UTP 4 pair CAT 6 LAN cable in the existing surface/ recessed PVC conduit as required.

Supply and fixing of following size of medium class PVC conduit along with accessories in surface / recessed including cutting the wall and making good the same in case of recessed conduit as rrequired.

Category 6 UTP Patch Cords - 1 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

Category 6 UTP Patch Cords - 2 Mtr Standard Colour - Blue, Grey, Yellow, RJ45 Plug - Polycarbonate plug, Current Rating - 1.5A max, Insulation Resistance - 500MΩ/km(min)@500 Vdc, Contact Resistance - 15 mΩ (max) per contact

24-port GbE Smart Managed Switch with GbE Uplink Interfaces-24 Ports 10/100/1000Mbps+4 SFP;Port Standards & Functions-IEEE 802.3 10BASE-T Ethernet (twisted-pair copper),IEEE 802.3u 100BASE-TX Fast Ethernet (twisted-pair copper),IEEE 802.3ab 1000BASE-T Gigabit Ethernet (twisted- pair copper),IEEE 802.3az compliance Auto-negotiation,IEEE 802.3x Flow Control; Full/Half Duplex-Full/half duplex for 10/100 Mbps speeds,Full duplex for Gigabit speed;Media Interface Exchange Auto MDI/MDIX adjustment for all twisted-pair ports;Switching Capacity 56 Gbps; Transmission Method Store-and-forward; MAC Address Table 16,000 entries per device, Maximum 64 bytes packet forwarding rate 41.7 Mpps,Packet Buffer Memory 1.5 MB,Maximum Power Consumption 22.45 watts, Standby Power Consumption 17.84 W/240 V, Acoustics 0 dBA Heat Dissipation 76.55 Btu/hr, Operating Temperature -5 to 50 ˚C (23 to 122 °F), Storage Temperature -20 to 70 ˚C (-4 to 158 °F), Operating Humidity 0% to 95% non-condensing, Storage Humidity 0% to 95% non-condensing, Diagnostic LEDs Link/Activity/Speed (Per 10/100/1000 Mbps port), Certifications CE (LVD) BSMICCC, C-Tick. Netgear / D-link/ Cisco.

Category 6, UTP 24-Port Patch Panel Size - 482.6mm x 44.2 (19’’ x 1U), Panel Material - Steel-fully powder coated, Unshielded - RJ 45, Plug Insertion Cycle - 750 times DC Resistance- 72Ω max, Voltage Rating - 72 Vdc max, Current Rating - 1.5A max

Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make.

Supplying and fixing of RJ 45 computer socket suitable for Cat 6 on module GI box along with base & cover plate in surface or in recess including making connection, soldering etc. as required.

Supply and fixing Metal/PVC Box of following size (normal size) on surcae or in recessed with suitable size of phenolic laminated sheet cover in front including painting etc as required.

Smart-UPS On-Line, 5.4 kW / 6 kVA with 1 hour Backup12 V 65 AH SMF Battery UPS Toplogy Double Conversion On-Line, Power Rating (VA / Watts) 5400Watts/6000VA, Form Factor Rack/Tower Convertible; Output Power Capacity 5400 Watts/6000 VA, Max Configurable Power 5400Watts/6000VA, Nominal Output Voltage 230V, Output Voltage Note Configurable for 220 : 230 or 240 nominal output voltage, Efficiency at Full Load 94.00%, Output Voltage Distortion Less than 3%,Output Frequency (sync to mains) 50/60 Hz +/- 3 Hz,Crest Factor 03:01,Waveform Type Sine Wave, Output Connections (1)*Hard Wire 3-wire (8)*(H N + G) IEC 320 C13(8),Bypass Built-in Bypass, Output Short Circuit Protection Yes,Parallel Redundancy (Option) 1 + 1, Nominal Input Voltage 230V,Input Power Factor>0.98,Input Frequency 40-70Hz,Input Connections Terminal Block, Protection Thermal Circuit Breaker (250VAC/20A), Input voltage range for main operations full load 160 - 285V, Input voltage range for mains operation half load 160-285V, High Voltage withstand Capability 420 VAC, Green Mode Range 210-250 VAC (230 V), Battery Type Mintenance - free sealed Lead-Acid battery with suspended, electrolyte. 12V 65 Ah SMF battery for 60 Min Battery Back up.

P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for horizontal run)

P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)

P/F testing joint, made of 20mm x 3mm thick copper Strip.125 mm long with 4 nos of tinned brass bolts nuts chuk nuts and spring washer etc complete as required.

Providing chemical/mineral maintenance free earthing system comprising of copper coated earth electrode 3 metre length and 17.2 mm outer dia along with 25 kg earth conductivity enhancing back fill mineral compound for earth electrode to fill up the excavated earth and earth inspection pit etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required (FOR LIFT)

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T

Supply and Installation of outdoor Bullet IR Network Camera 1/2.7" CMOS, ICR, 2592*1944@ 25fps, 5 MP H.265/H.264/MJPEG, Triple streams, DC12V & PoE, Micro SD card slot up to 256 GB, Alarm in/out , Audio 1/1, IP67, 2.7-13.5mm Motorized Varifocal lens, IR anti-reflection window, Built-in bracket, IR range: up to 50m, Digital WDR Range, 3D-DNR for noise reduction, Audio In and Out, Alam in and Out IPv4 network supported, IP67 rated for weather proofing, ONVIF, POE IEEE 802.3af, (UL, FCC, CE, BIS certified). Make-Panasonic/ Bosch/Honeywell

Supply / Installation and Commissioning of Network Video Recorder,H.26+/H.265/H.264/H.264+ video formats,Connectable to the third-party network cameras,Up to Min 32 IP cameras can be connected,Recording at up to Min 8 MP resolution,Supports live view, storage, and playback of the connected camera at up to Min 8 MP resolution,HDMI and VGA independent outputs ,HDMI Video output at up to 4K (3840 × 2160) resolution ,4 SATA interfaces connectable for recording and backup ,2 self-adaptive 10/100/1000 Mbps network interface ,Centralized management of IP cameras,

Supplying and laying of SOLID CABLE, CAT6 UTP, 4PAIR, 23AWG, LSZH CM,BLUE colour through existing conduit /trunk complete as required & as per Direction of Engineer-In-Charge.MAKE : DIGISOL/DIGILINK

Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Aspect Ratio 16:9, Native Resolution 1920 x 1080 (FHD), Brightness 350nit or Higher, Contrast ratio 1100:1 or Higher, Dynamic CR 500,000:1 or Higher, Viewing Angle (H x V) 178 X 178, Orientation Portrait & Landscape, Operation Temperature 0 ⁰C to 40 ⁰C, Safety UL, eUL , EMC FCC Class “A”, IP video input 16 Channel , 1-ch, RCA (2.0 Vp-p, 1KΩ) Two-way audio input, 100Mbps Incoming bandwidth, 80Mbps Outgoing bandwidth, 128 Remote connection, HDMI/VGA output : 1-ch, resolution : 1920 × 1080P /60Hz, 1600 × 1200 /60Hz, 1280 × 1024 /60Hz, 1280 × 720 /60Hz, 1024 × 768 /60Hz, Audio output 1-ch, RCA (Linear, 1kΩ), Live view / Playback resolution :

Hard Disk 4 TB

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600mm X 600mm X3mm thick including accessories. a nd providing masonary enclosure with cover plate having locking arrangement and watering pipe 2.7 metre long etc. ( but without charcoal/ coke and salt ) as required

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal / coke and salt as required.(For Transformer Neutral)

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supply and erection of 7 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 155 mm, made of 3 mm thick sheet along with base plate of size 260 X 260 X 16 mm , small door opening for junction box mounting 6A 'C' series SP MCB, connector, and suitable size foundation bolts with template as required (but without pole foundation)

Supply and erection of 4 metre height Hot-dip galvanized octagonal street light pole with following arm with top dia 70 mm and bottom dia A/F 130 mm, made of 3 mm thick sheet along with base plate of size 220 X 220 X 12 mm , small door opening for junction box mounting including 6A 'C' series SP MCB, connector and suitable size foundation bolts with template as required. (but without pole foundation )

Supplying and fixing following types LED street light with minimum efficacy 100 lm/w in die cast aluminium housing, toughened glass, lP 66 protection and complete with electronic driver etc on pole/building including connection earthing the body etc as required.

Supplying & embedding of following dia G.I. pipe (medium class) in pole collor / foundation (during casting ) for cable entry including bending the pipe to the required shape complete etc. as required.

Meter

Supplying and fixing post top / gate light (width 250/300 mm) made up of high grade unbreakable polycarbonate material suitable for upto 20 watt LED lamp including connections and earthing the body etc as required. ( But without lamp)

Supply and fixing fabricated Feeder pillar of cubical construction, floor mounted type, fabricated out of 14 SWG CRCA sheet, compartmentalised with hinged doors, dust and vermin proof, powder coated painting of approved shade after 7 tank treatment process, cable alley, internal wiring, earth terminals, Bus bar Chamber, insulator, with 40mm X 40mm X 5mm angle iron stand and complete in all respect etc and must be CPRI approved panel manufactures. (But without RYB LED lamp, ammeter, voltmeter, inter-connection copper conductor cable/solid copper strip, switchgears, PCC work etc.)

Supplying and fixing of following rating electrical items in the existing cubical panel board/ feeder piller including drilling holes in cubicle panel/ feeder piller making connections etc. as required .

40 Amp to 63 A raiting, TPN MCB, "C" curve, 10KA breaking capacity.

50 mm x 5 mm copper strip (2.30 kg / mtr.)

Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.

APFC CAPACITOR BANK PANEL -I

4 Nos. 15 KVAR & 2 Nos. 20 KVAR MPP type capacitors with associated 63 Amp TP MCCB's, AC3 duty contactors with each capacitor bank and 6 step relay for automatic and manual operation of capacitors, necessary indication lamps / toggle switch etc and required inter connections complete.

EXTERNAL LIGHTING - FEEDER PILLAR

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Excavation for foundation in soft soil including dressing of sides and ramming of bottoms lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil directed within lead of 50 metres.

Providing and laying in position cement concrete 1:2:4 ( 1: cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size )in foundation of pump DG set , feeder pillar and refilling etc. as required

Providing and fixing MV danger notice plate of 200mmX150mm made of mild steel at least 2mm thick, and vitreous enamelled white on both sides, and with inscription in single red colour on front side etc as required.

DISTRIBUTION BOARD (DB):-

Supplying and fixing following way single pole & neutral, sheet steel, MCB distribution board, 240 volts, on surface/ recess, complete with tinned copper bus bar, neutral busbar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCBilsolator)

Supplying and fixing following rating, 2401475 volts, "C" curve, miniattlre circuit breaker suitable for lnductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing following rating 240/415 Volts, "C" series miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required.

HV CABLE SUPPLY

3 core, 185 sq. mm , 11 KV grade, armoured power H.T. cable , XLPE insulated with PVC sheathed & aluminium conductor

HV CABLE LAYING

Laying one PVC ated PVC XLPE powe r cable of 11 KV grade of following size direct in ground incl uding excavation, sand cushioning, Protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Metre

Supply of following sizes and core of PVC/XLPE insulated PVC sheathed heavy duty, aluminium conductor armoured under ground cable of graded 1.1 KV for working voltage upto 1100 volts conforming to ISI 1554 (Part-I) of 1964 with upto date amendment as detailed below.

Laying of one number insulated and PVC sheathed power cable of 1.1 KV grade of following size direct in ground including excavations, sand cushioning protective covering and refilling the trench etc. as required.

Laying and fixing of one number PVC insulated and PVC sheathed aluminium conductor cable of1.1 KV grade of following size on surface etc. as required.

Supplying and laying of following size DWC HDPE pipe lSl marked along with all accessories like socket, bend, couplers etc. conforming to lS 14930, Part ll complete with fitting and cutting, jointing etc. In the existing trench, complete as required.

Meter

Meter

11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.

Rubber mat of 16mm thik and 1000mm wide to with stand 15kv dielectric strength as per is 5424. 1969

Shock treatment chart in English and local language duly framed with glass

First aid box complete with all standard first aid materials

Rubber gloves 11 KV grade as per IS 4770-68

Supply installation testing and commissioning of 5.0 LB Noves 1230/FK-5-1-12

Supply fixing testing and commissioning Lienear pneumatic heat Detection

Supply fixing testing and commissioning of Master Control Unit for controlling each system, complete with pressure switches, buzzers and electronic hooter, including all necessary accessories + electrical wiring to make each entier system functional (Make - Firetrex / Tracefire / Safefire).

Supply, installation, testing and commissioning of Silent Type diesel generating set comprising of engine CPCB IV Model 199 BHP @ NTP , 1500 RPM Coupled to 160KVA 3 PHASE 415 VOLT ,50 HZ Alternator mounted on acommon base frame along with other accessories i.e. fuel tank AMF CONTROL PANEL, BATTERY WITH LEADS AND ACOUSTIC ENCLOSURE (CPCB-4 Standard)

Supply, erection, testing and commission of MRL lift Half portion of Glass Door travelling from ground floor to 5 th floor, stopping at 6 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required. (Make:-Thyssen/OTIS/KONE/Schindler/Johnson only)

After Warrenty/ Guarenty

Supply, erection, testing and commission of MRL lift Half portion of Glass Door travelling from ground floor to 5th floor, stopping at 6 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required. (Make:-Thyssen/OTIS/KONE/Schindler/Johnson only)

Supply, erection, testing and commission of MRL lift travelling from ground floor to 3 rd floor, stopping at 4 floors and opening on one side only with/without attendant complete with light in lift shaft and lift pit, providing ladder in lift pit, providing necessary scaffolding required for erection of lifts and minor buildings work comprising of cutting holes and making good the same for the car, counter weight, brackets, call buttons and indicators and including painting of all steel items as required.

After Warrenty/ Guarenty

Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mountedon Aluminium/GI structure of suitable strength with following components complete as required:-a)Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/ IEC61215, IS/IEC61730-Part-1, IS/ IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% attheend of 25 years. b)Power Conditioning Unit (PCU) of 350-800V DC Input voltage range and 400V AC, three phase, 4 wire, 50Hz+/-2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than3% and suitable for ambient temperature from 0 to 50 degreeC. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. (Make-Heron India Pvt ltd / Ojas Solar Energy/ Solar Power Tech) Note:-All Electricals & Mechanical items included.