8148/21-22 PROVN OF BOUNDARY WALL AND SPECIAL REPAIR TO BLDG NO T-193, P-122 AND T-165/01/16 AT KARU UNDER GE 860 EWS

Amount

Excavating in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation getting out hard/dense soil complete all as per specified and as directed.

Returning, filling in, in soil, including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in each layer complete all as per specified and as directed.

Removing excavated material/soil to distance n.exc 50 m and depositing where directed at a level n.exc1.5m above the starting points complete all as per specified and as directed.

Providing plain cement concrete 1:4:8 type D2, using 40mm graded crushed stone aggregate as in foundation of column footing and plinth beam/beam complete all as specified and as directed.

M & L Precast cement concrete block masonry type C1 1:3:6 (20mm graded crushed stone aggregate) with solid blocks, exc. 10cm in width and, setting in cement mortar 1:6 complete all as Specified.

Rendering 20mm thick in CM (1:4) using water proofing compound as per manufacturer's instruction in two layers, finished even and smooth surface without using extra cement - External Plaster (WPC measured and paid separately) complete all as specified and directed.

M&L for preparation of new plastered surfaces and apply two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for Providing, cement concrete type B1, 1:2:4 (using 20mm graded crushed stone aggregate) as in coping including formwork (straight or curved) and finishing (Reinforcement shall be measured and paid separately) Complete all as specified and as directed by Engr-in-charge.

S&F Framed work such as grills, grating, etc with ends of bars shouldered and/or welded and iron doors, ladders, framed structure, railing and Similar work etc complete all as specified and directd.

M&L preparation of new or previously untreated steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified

Supply only liquid water proofing compound ( Make Dr . Fixit or approved by GE)

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engr-in-Charge

M&L for non skid ceramic coloured tiles 7 to 8mm thick (Square/ rectan-gular) area of each tiles exceeding 0.06 sqm but not exceeding 0.11 sqm, in floor etc set and joint in neat cement slurry and pointed in white or coloured cement to match coloured tiles over 15mm thick screed bed in CM (1:6) complete all as specified and directed by Engr-in-Charge

M&L for non skid ceramic coloured tiles 7 to 8mm thick (Square/ rectan-gular) area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and joint in neat cement slurry and pointed in white or coloured cement to match coloured tiles over and including 15mm thick screed bed in cement mortar (1:6) complete all as specified and directed by Engr-in-Charge

M&L for Glazed ceramic coloured tiles of size 300x200x7mm thick in vertical surface such as skirting/dados and risers to steps etc , set and jointed in neat cement slurry and pointed in coloured cement to match coloured tiles over and including 10mm thick screed bed in cement mortar (1:4) complete all as specified and directed by Engr-in-Charge

Demolition of Bricks work or stone/boulder masonary, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stonework and precast concrete aritcles complete all as specified and directed by Engr-in-Charge

Taking down cement plaster on brick or stone etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed by Engr-in-Charge

M&L Rendering 15 mm thick on fair faces of brick work or concrete surfaces in CM 1:4 is to be finished even and smooth (without using extra cement) complete all as specified and directed by Engr-in-Charge

M&L preparation of new plastered wall surfaces of any description and applying three coats of white wash on walls bands cornices, off sets, pillar etc all as directed by Engr-in-Charge.

Taking up or down 15mm bore steel tubing and connections including cleaning for refixing with all fittings complete all as specified and directed by Engr-in-Charge

Taking up or down 20mm bore steel tubing and connections including cleaning for refixing with all fittings complete all as specified and directed by Engr-in-Charge

S&F of 15mm bore medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors complete all as specified and directed by Engr-in-Charge

S&F of 20mm bore medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors complete all as specified and directed by Engr-in-Charge

S & F in repair of Stop valves 15mm bore fancy type, chromium plaed screwed down, high pressure with crutch or buttrefly handle screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge

S&F in repair of CP Angle cock 15mm bore all as spd and directed by Engr-in Charge

Supply and fix in repair 15 mm bore bib tap chromium plated fancy type with crutch or butterfly handle screwed down, screwed for iron pipe fixed in repairs all as specified and directed.

S&F in repairs of Vitreous china wash down water closet pan (Pedestal type) white including removing the existing one complete and making good all connection including white plastic seat cover solid confirming to ISI complete all as specified and directed by Engr-in-Charge

Supply and fixed in repair vitreous china wash hand basin including brackets, white size 550 x 400 mm incl cutting cutting for and pinning in ends of brackets. Including Waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other complete all as specified and directed by Engr-in-Charge

S&F 32mm dia bore waste fitting brass chromium plated fixed to wash hand basin, sink with long screwed shanks and fly nuts flange and bedded in run lead cement and other end fixed complete all as specified and directed by Engr-in-Charge

Supply and fix in repairs 15mm bore pillar taps CP brass chromium plated fancy type screwed down high pressure with chromium plated screwed shanks and fly nuts complete screwed for iron pipe complete all as specified and directed by Engr-in-Charge

S&F 32mm dia PVC waste pipe with fly nut, copling for sinks/urinals or wash basins complete all as specified and directed by Engr-in-Charge

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with ball valve and handle/push button 32mm dia PVC flush pipe complete all as specified and directed by Engr-in-Charge

Supply and fix in repairs15 mm bore LDPE pipe 45cm long with brass nuts and washers on both ends all as in repairs specified and directed.

S&F for 20mm dia CP brass tubular Towel rail & 600mm long complete all as specified and directed by Engr-in-Charge

Dismantiling of cast iron SWR pipes from any position of 75mm dia complete all as specified and directed by Engr-in-Charge

All as per Srl item No 36 here-in-before but 100mm dia

S&F PVC (SWR) pipes 75mm dia length with rubber ring joints fixed to wall complete all as specified and directed by Engr-in-Charge

All as per Srl item No 38 here-in-before but 110m dia

S & F 75mm dia PVC (SWR) floor trap plain with grating including jointing to waste pipe fixed in solvent cement or cement concrete 1:2:4 type B1 complete all as specified and directed by Engr-in-Charge

S & F PVC(SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by Engr-in-Charge

S & F 110mm PVC(SWR) bends any radius complete all as specified and directed by Engr-in-Charge

All as per Srl item No 42 here-in-before but 75mm dia

S & F PVC(SWR) vent cowl 110mm dia all as specified and directed.

Dismantling water tank exc 500 ltr but n exc 1000 ltr and removing to store complete all as specified and directed by Engr in Charge

Dismantling water tank not exc 500 ltr and removing to store complete all as specified and directed by Engr in Charge

S&F 1000 Ltrs capacity Rotaional moulded, polythene water storage tanks (cylindrical shape with vertical threaded top closed) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore all as specified in SSR Part I complete all as specified and directed by Engr-in-Charge.

S&F of rotantional moulded polythylene water storage tanks 500 ltr capacity (cylindrical vertical with threaded closed top ) hoisted and fixed in position complete with ball valve of high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball and screwd for iron pipe 20mm bore omplete all as specified and directed.

S&F 20mm bore pipe gun-metal globe or gate valves with iron wheel head screwed both ends complete all as specified and directed by Engr-in-Charge.

S&F 20mm dia metal powder coated curtain rod including wooden finish curtain fancy type brackets fixed to walls and curtain rings 8 Nos per RM (Minimum) etc complete all as specified and directed by Engr-in-Charge

Taking down chowkats/window with shutters without taking off shutter from frame area n. exc 1.5sqm complete all as specified and directed by Engr-in-Charge

Taking down chowkats/frames of area exc 1.5 Sqm and n. exc 4 Sqm with shutter (without taking off shutters from the frame) each complete all as specified and directed by Engr-in-Charge .

M&L for 2nd class hard wood plain solid straight chowkhts and frame wrought framed rebated on the solid rounded or chamfered out together with glue pinned at joints complete all as specified and directed by Engr-in-Charge

S&F factory made 35mm thick second class hard wood plain framed paneled shutters (two panels) with lock rail and panels of 9mm BWP commercial ply or 12 mm veneered particle board for others with commercial veneering on both faces and size of members of doors shutter as per IS 1003(part-I) as specified in SSR part -I section 3 clause 8.20 (a) fitted to chowkats, kiln seasoned and chemically pressure treated complete all as specified and directed by Engr-in-Charge

M/L for glazed and skelton shutters 30 mm thick 2nd class hard wood, open rebated and prepared to receive glass, guage, etc, divided in to square with plain, chamfered or rounded mitred and rebated sash bars, any numbers, complete all as specified and directed by Engr-in-Charge

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying & fixing in opeing as per specification, complete all as specified and directed by Engr-in-charge.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification, complete all as specified.

S& F MS Butt Hinges medium weight, cold rolled 125 mm size complete all as specified and directed by Engr-in-charge.

S&F 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed by Engr-in-Charge .

S&F 150mm Extruded Aluminium alloy handle fabricated type anodised complete all as specified and directed by Engr-in-Charge

S&F 45cm long aluminium peg set of 6 all as spd and directed

S&F 3mm thick Figured glass, pin head type and glazing with oil putty in squares n.exc 0.5 sqm in each pane complete all as specified and directed by Engr-in-charge.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane complete all as specified and directed by Engr-in-charge.

M&L for painting two coats of synthetic enamel paint over one coat of pink primer incl necessary preparation of new wooden surface of any description over 10 cm width or girth complete all as specified and directed by Engr-in-charge.

Dismantling plain or corrugated steel sheeting any guage, thickness including nainital or similar pattern roof covering and wall cladding complete all as specified and directed by Engr-in-Charge

S&F of galvanised, corrugated mild steel sheeting 0.50 mm thick with two corrugations side lap, fixed with L-type or J-type or cranked hook bolts in lieu of screws with rubber washers with grade of zinc coating 275 complete all as specified and directed by Engr in Charge

S&F of 0.50mm thick plain mild steel sheeting in ridges, hips, valley gutters,drip and straight flashings (length and girth as fixed) fixed with L-type or J-type or cranked hook bolts in lieu of screws with rubber washers with grade of zinc coating 275 complete all as specified and directed by Engr in Charge

M & L for two coat of synthetic enamel paint of approved tint on steel and iron surfaces of any description over 10 cm width or girth not otherwise described including preparing new zinc(or galvanised) surfaces to receive painting by coating with mordant solution incl washing and cleaning, etc. over a coat of red oxide complete all as specified and directed.

Dismantiling of boarding any description, fixed in any position with nails complete all as specified and directed by Engr-in-Charge

Dismantling of timber scantiling/ fillet, rails, posts, purline etc in frame work under 40 Sq cm in any position complete all as specified and as directed .

M&L second class hard wood timber scantling plain fillets, square, rectangular or triangular in section clear swan, sectional area exc 13 sqcm & not exc 25 sqcm, secured with nails or brads .

M&L 9 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work in walls complete all as specified and as directed complete all as specified and directed by Engr-in-Charge

M& L for veneered decorative plywood 6 mm (5 ply) thick grade 1 with BWR resin with decorative face veneers one face fixed with nails to timber frame work as in ceiling complete all as specified and directed by Engr-in-Charge

Demolition of toilet area (approx plan area 1 sqm to 2 sqm) sunken portion ,removal of demolised material, cleaning the side/bottom of sunken floor with wire brushes, and rendering 15mm thick in cement mortar 1:3 with water proofing compound, drying to receive the water proofing material and applying two coat of Dr. Fixit 2K in the sunken portion (floor & sides) as per manufactures instructions and directed by Engineer-in-charge and testing for leak proof by ponding test, laying and joining of pipes and spouts and filling with PCC 1:5:10 type E2 (40mm graded stone aggregate) in mass concrete for lean concrete of WC/ Bath complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (below or above ground level) complete as specified

Demolition of brick work or stone/boulder masonry built in cement mortar including all quions arches pillars etc but excluding ashlar facing dressed stonework and precast concrete articles

M&L for 40mm thick cement concrete Type B0,1:2:4 (12.5mm graded aggregate)etc complete all as specified and directed by Engr-in-Charge

Hacking out old broken glass exc 1.5 sqm (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and directed

S&F of 4mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and directed by Engr-in-Charge

M&L for securing glass of any description in existing metal frames glazed with putty/beads including removing loose or decayed putty/beads, painting/oiling one coat on rebates, grooves, reputttying and painting/oiling puttied surface to match existing work (new length of frame reputtied shall be measured)

S&F of 35mm thick, flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engr-in-Charge

Taking down, refixing in same opening, resecuring or easing & adjusting, without taking down shutters of any description exc 1 sqm and n. exc 2 sqm removing of unserviceable complete all as specified and directed by Engr-in-Charge

S&F of 300mm length aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixed clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and directed by Engr in Charge

M&L for rendering 15mm thick in cement plaster 1:6 on fair faces of brick work or concrete surface to be finished even and smooth (without using extra cement) complete all as specified

M&L for rendering 5mm thick in cement plaster 1:3 on fair faces of brick work or concrete surface to be finished even and smooth (without using extra cement) complete all as specified

M&L for preparation of new plastered surface of ceiling and applying three coats of white washing and preparity to plastered surface complete all as specified and directed.

S&F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete all as specified and as directed by the Engineer-in-Charge

S&F in repair of Vitreous china Urinal bowl, flat back,size of 465x355x265mm white minium with grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securign urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement (excluding flushing cistern, flush pipe) and incl waste pipe withdischarge arrangement complete all as specified fixed in repairs.

S&F urinal spreader of PTMT of any colour for fixing with 15mmdia pipe complete all as specified and directed.

S&F in repair bib taps,15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S&F of 3 layer 20mm PP-R Poly-propylene random copolymer concealed pipes SDR 7.4 (PN-16) UV stablized and anti-microbal fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fitting fixed in ceiling/walls or in floor complete all as specified

S&F in repair of 20mm PP-R Gate valves (brass insert) as per requirement of site complete all as specified and directed

M&L for Plain cement concrete 1:3:6 type C-1 using 20mm graded crushed stone aggregate as in coping, benching bed plates and the line including necessary form work and finishing all exposed surface of concrete as per clause 4.11.16.2(a) of SSR Part-I(1991) complete all as specified and directed by Engr-in-Charge.

M&L Concrete bed 1:4:8 type D-2 to drain pipes incl packing under and haunching against the sides of pipes after they are laid and tested bore of pipe in 150 mm.

Dismantling of cast iron pipe or reinforced concrete drain pipe, jointed in cement mortar of 150mm dia fixed on walls, floors, complete all as specified and directed

S&F of 100mm cast iron spun pipes soil, waste and vent pipes in any length with or without ears, with cement joints, fixed on walls complete all as specified

S&F of 75mm cast iron spun pipes soil, waste and vent pipes in any length with or without ears, with cement joints, laid in trenches or floors complete all as specified

S&F of 100mm cast iron Bends (any radius) diminishing piece or tapers (larger bore measured) complete all as specified

S&F of 75mm dia cast iron Bends (any radius) diminishing piece or tapers (larger bore measured) complete all as specified

S&F of 100mm dia cast iron branch pieces double (equal or unequal) ordinary or inverted (spigot or socket type) or parallel branches

S&F of 75mm dia cast iron branch pieces single (equal or unequal) ordinary or inverted (spigot or socket type) or parallel branches

S&F of 100mm dia cast iron socket (double) collars compelete all as specified and directed

S&F of 75mm dia cast iron socket (double) collars compelete all as specified and directed

S&F of 150mm dia reinforced concrete pipes, NP2 laid and jointed complte with collars complete all as specified and directed

M & L water proofing treatment including taking down of old roof treatment to roof slab with APP based modified polymeric membrane centre core 100 micron HMHDPE outer film 20 micron each having thickness 2mm weight not less than 3 kg/sqm with 100mm overlap laid as per manufacturers instructions, complete all as specified and directed by Engineer-in-charge with following courses of description below:- ( a) Applying evenly a coat of bitumenous primer confirming to IS-3384-1965 @ 0.40 kg/sqm on prepaired surfaces till the surface is properly impregnated. (b) Second coat of bonding material using blown grade bitumen 85/25 conforming to IS-702 @ 1.20 kg/sqm ( c) third course is laying ao APP based modified membrane described hereinbefore with 100mm overlap in longitudinal direction and 100mm in tranverse direction, all joints and changes in all directions should be curved with cement mortar (1:3) mixed with SBR latex @ 200ml per bag of cement and cured well before laying the membrane. (d) Forth coat of bonding materials using blown grade bitumen 85/25 confirming to IS-702 @ 1.20 kg/sqm complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in ground floors and pavings n exc 15cm thickness (below or above ground level) complete as specified

M&L for reinforced cement concrete B1 1:2:4 (20mm graded aggregates) on slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete as specified

M&L mild steel TMT bars 10mm dia and over cut to length bent to shape required including cranking bending spirally for hooping for columns hooking ends for binding with and including mild steel wire (annealed)not less than 0.9mm dia or securing with clips quality confirming complete all as specified and directed

M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;rough finished surface, not exceeding 200mm thick (Horizontal or sloping

M&L for formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide

Dismantling wall/ceiling board(fibre,pulp insulation etc.) or insulation boards/slabs/blankets, any thickness including fillets complete all as specified and directed.

S&F for anodised aluminium snap grid frame work for false ceiling (grid size 605x605mm) fixed to walls with rawl plugs and screws and hang to roof members with 6mm dia GI wire (upto 1200mm length) adjusting level fixed to roof slab by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastners 12.5mm dia 40mm long with and including 12mm thick perforated particle board of 60x60cm in size fixed or laid / inserted to timber /GI/ Aluminium frame work complete all as specified and directed.

M&L for veneered decorative plywood 4mm thick (3 Nos of ply) grade 1 (with BWR resin) with decorative face veneers one face fixed with nails to timber frame work complete as in wall paneling complete all as specified & directed.

M&L for decorative type soft wood corner beading 30mm wide fixed on plywood complete all as directed by Engr-in-charge.

S&F for aluminium anodised powder coated partition complete of style top rail, side rail 83x44x2mm thick and bottom rail 83x44x2mm thick and glazing with 5mm thick linted glass or 19 particle board complete including rubber lining at sides for air locking complete all as specified and directed

Demolition and breaking up drain pipes 100 mm dia (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

S&F in repair 16mm 3-layer PP-R Polypropylene random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc complete all as specified and directed by Engr-in-Charge.

M & L for SDC Laminated flooring 8mm thick of any coloured manufactured by Direct pressure laminated (DPL wherein the empty Abrasive aluminium oxide overlay alongwith mentamine impregnated decorated film is directly fused with the back with flooring locking profile in designed with double click locking system on the length and single locking width alongwith desire locking strength complete all as specified and directed by Engr-in-Charge.

Taking down carefully alluminium / copper point wiring complete for light, fan, socket or power point etc with fittings fixtures such as ceiling rose, holders, electric fittings, switchs, sockets, aluminium conductor cable with and incl wooden batten or FR PVC conduit and its accessories such as wooden gutties, rawl plugs, GI screws, aluminium clips, nails etc complete and removing the material from site and making good the disturbed surface of wall / floor/ ceiling etc as original i.e. brick work, plastering, white washing, OBD etc as required, complete all as specified and directed.

M&L point wiring for one light / bell / buzzer / exhaust fan point controlled by one no, 1-way, 5 Amps switch complete with single core FRLS PVC insulated, unsheathed, multi stranded copper conductor cables 1.5 Sqmm 1100 volts grade, with and incl 1.5 Sqmm FRLS PVC insulated, unsheathed, multi stranded copper conductor cables as continuous earth wire connected to metallic bodies of luminaries / fans etc at one end and to common earth dolly at other end, complete wiring drawn through & PVC casing and capping of 25 mm and above (as per conductor run ) medium grade, ISI marked, incl all accessories & fittings / junction boxes / inspection covers etc, with and incl concealed MS sunken box of suitable size flush with wall surface, covered with & incl 3 mm thick bakelite, laminated hylem sheet / Gang box for top cover suitable for fixing of piano type switches / sockets etc, complete all as specified and directed for the following :- (Note : The cost of MS sunken box with 3 mm thick bakelite, laminated hylem sheet top cover is deemed to be included in quoted rate.)

All as per srl item no. 120 here-in-before but for one socket outlet 3 pin, 5 Amps on independent board.

All as per srl item no. 120 here-in-before but for one socket outlet 3 pin, 5 Amps on same board.

All as per srl item no. 120 here-in-before but with 2.5 sq mm FRLS copper wire with 2.5 Sqmm FRLS copper earth wire for indpendent 15 Amp point.

S&F of Switch piano type, single pole, one way, 5 amps, 230 volts, complete all as specified and directed.

S&F of Socket, two-in-one, 5 pin, 5 Amp, universal type, 230 volts, complete all as specified and directed.

S&F of Switch piano type, single pole, one way, 15 amps, 230 volts, complete all as specified and directed.

S&F of Socket, 6 pin, 5/15 Amp, multipurpose shutter type, 230 volts, complete all as specified and directed.

S&F of Lamp holder, metal cased, bakelite body, 230 volts, complete all as specified and directed.

S&F LED lamp 15W complete all as specified and directed by the Engineer-in-Charge. Make : Havells / Wipro / Osram

S&F of Ceiling rose, two to three terminals, bakelite body, 230 volts, complete all as specified and directed.

Supply and fixing in replacement 20W 6000K LED batten and making connection to ceiling rose by 23/0.0076 copper flexible wire all as specified and directed at site. Make : Havells cat part No LHEXBXPNIN1W020 / Compton Greeves / Wipro / Philips

S&F in replacement of recessed mounted LED light fitting of 2' x 2' size, suitable for false ceiling, 36 Watt, 6500K white light, metal body with white colour outer finish and acrylic diffuser including LED driver / transformer, spring loaded clips for easy mounting and making all electric connections complete all as directed.

S&F in replacement bulk head fittings of Environmental friendly, ultra modern, energy saving, surface mounted, decorative oval plastic bulk head fitting 14W LED 6000K luminaire comprising of high brightness LEDs, IP54 protection. Make : Havells Cat Part No LHFOECE1TZ1B014 /CG / Wipro / C&S

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 8 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F in replacement of DB, double Door, made out of CRCA mild steel sheet surface with insulated material like polyester or with epoxy powder coating and IP 43 & IK 09 protection, SPN 4 way, 240 volts with bus bar rating 200 Amps, dust and vermin proof, suitable for incorporation of MCB’s and isolators etc and making all necessary connections, duly flush of wall surface, complete all as specified and directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F in replacement of MCB, C Curve type, 10 kA, 40 to 63 Amp, SPN with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F in replacement of MCB, C Curve type, 10 kA, 6 to 32 Amp, Single Pole with over load and short circuit protection, complete all as directed. Make : Schneider Elect / Legrand / C&S / Hager

S&F plastic ventilating fan 250 mm sweep including louvers with cutting chases on brick wall and grounting with nut bolts on aluminium frame complete all as specified and directed by Engr-in-charge. (Make : Crompton Cat Part No : Brisk Air 10" / Bajaj / Orient )

M&L for earthing with galvanized steel earth plate electrode of size 600 x 600 x 6 mm buried directly in ground earth pit not less than 2.25 mtr below of normal ground level with top edge of earth plate should not less than 1.5 mtr below normal ground level and connected to galvanized iron earth lead wire of size 4 mm dia by means of bolts, nuts, washers of galvanized iron or steel all as shown in electrical plate No.3 of MES SSR Part I connecting to earthing test point on completion with and including 15 mm bore GI light grade protection pipe (7.5 mtr long) for earth lead GI lead wire 4mm dia (7.5 mtr long), PCC pit with cover in PCC 1:2:4 type B-1 reinforced with 8 mm dia tor bars @ 80mm C/C, 20mm dia medium grade watering pipe with funnel, wire mesh, common salt, charcoal, necessary excavation and earth work, complete all as specified and directed.

Supply and laying XLPE insulated, armoured, heavy duty electric cable, with stranded aluminum conductor 1100 V grade nominal cross sectional area 10 Sqmm, 2 core laid in trenches, ducts, drawn through pipes across the road/path/along poles/wall/floors/equipment etc including jointing and testing complete all as specified and directed by the Engr-in-Charge

M&L for factory made un-reinforced pre cast concrete cable protection cover LV class type - I with size 250mm x 150mm x 40mm laid across the cable (i.e. width of cover along the length of cable) for UG cable protection on the top of the sand cushioning, complete all as specified and directed by Engr-in-Charge.

Material and labour for sand cushioning to under ground electric cable all as per clause No 19.75 of MES SSR Part-I (1991)

Supply and fixing round shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and fixing LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size

Taking out old unserviceable/serviceable un-reinforced concrete PCC cable covers from excavated trench all as directed by the Engineer-in-Charge. Note:- Serviceable un-reinforced concrete PCC cable cover kept in safe custody for reuse at site and unserviceable un-reinforced concrete PCC cable cover through in low lying area.

Laying only old reinforced PCC cable cover of any size as retrieved from serial item No-146 here-in-before, complete all as directed by Engineer-in-Charge.

CHHIRPON BUILDERS

M/S GEE GEE ENTERPRISES

tamchos gurmet

M/S GEE AAR and SONS ENTERPRISES

MS INFRATECH