REPAIR AND MAINTENANCE OF OLD RCC/GI/CI/DI PIPE LINE OF VARIOUS SIZE AND CONNECTED ITEMS UNDER GE SAUGOR

Amount

Carry out day to day rectification of water supply complaints at Area I & Area II like Leakege of water supply line any sizes, brocken/Crack of the GI/CI/DI Pipes any sizes, replacement of unserviceable Gate valves, replacement of gland rope and rubber packing to any size of Sluice valves etc complete all as directed by the Engineer-in-Charge Note: (i) Replacement of GI Fittings shall be measured and paid separately. (ii). GI Pipe shall be mesured and paid separately. (iii). If required excavation and earth work will be measured and paid separately. (iv). Materials like Lead,Gate valves, gland rope,rubber packing, Shealloc bottole,cotton thread etc shall be measured and paid separetely (v). Pipe fitter with Helpers so detailed by the contractor will report to MES complaint cell at 08.45 Hrs morning to receive complaints(Complaint slip provided by the contractor) from department and complaint should be rectified with in a same day. (vi). Rate included with transport vehicle provided by the contractor to attending the complaints Area I & II .(vii). Attending the complaints not less than min two complaints per day

Excavation in trenches in hard/dense soil not exc 1.5m wide & not exc 1.5 deep and getting out in hard/dense soil complete all as specified and directed

Excavation in trenches in hard/dense soil additional 1.5 m or part thereof in depth beyond the first 1.5m complete all as specified and directed

Removing excavated material outside MD not exc 50m and depositing where directed at a level in n.exc 1.5m above the starting point in soil complete all as specified and directed

Returning filling in including spreading , levelling watering and well ramming in layers not exceeding 25cm complete all as specified and directed

Supply and laying GI tubing, medium grade galvanised with all fittings specials such as bend, elbows,tees, short pieces connection, back nuts, diminishig pieces, caps, plugs and unions etc laid in trenches or ceiling of following bore including taking out existing GI tubing complete all as specified and directed (Note: Excavation and earth work will be measure and paid seperately):-

15 mm bore of pipe

20mm bore of pipe

25mm bore of pipe

40mm bore of pipe

50mm bore of pipe

80mm bore of pipe

100 mm bore of pipe

S&F Gun metal gate valve with iron wheel, screwed both ends for iron pipes of following sizes including taking out existing gate valve of any type complete all as specified and directed:-

15 mm dia

20mm dia

25 mm dia

40 mm dia

50 mm dia

S&F new sluice valve size of 450 mm dia CI body ISI marked class PN 1.6 heavy duty flanged ends cast iron wheel with Brass spindle (ISI marked) conforming to IS : 14786 – 2000, short body all as specified including nuts ,bolt, washers and gasket including taking out existing sluice valve complete all as specified and directed. Note: Quoated rate deemed to include making good the damaged valve chamber.

S&F cast iron bends (any radius and angle) tappers any type (straight, bend, increasing, decreasing or double socket) Tee, pieces single branch, “ Y” junction, double branch, cross ( all socket or socket spigot) collars, caps, caps & plugs of the size upto 450mm dia complete all as specified and directed.

Supply and lay connecting, jointing and testing of Ductile iron pipe fittings ( Specials ) heavy duty for any type ( flanged / socketed ) pipes such as, bends ( any type radius, and angle ), tapers, any type straight bend, increasing, decreasing or double socket etc. Tee pieces, ring branch, Y junction, double branch, cross ( all socket or socket and spigot ), collars, caps and plugs, adapters etc. of any size radius and length conforming to IS 9523 / 2000 specifications with external bitumen coating and internal cement mortor lining and metallic zinc coating of size upto 500 mm bore complete all as specified and directed.

M&L for the spigot and socketed DI pipe Tyton rubber joint for the following sizes complete all as specified and directed:- Note : Earth work shall be measured and paid separately under respective items.

80 mm bore

100 mm bore

150 mm bore

200 mm bore

300 mm bore

350 mm bore

400 mm bore

450 mm bore

500 mm bore

Supply, laying connecting, jointing and testing centrifugally cast (Spun) Ductile iron Pressure Pipe ISI marked confirming to IS -8329-2000 (Reffirmed-2005 Edition 4.1) of 450 mm dia size with socket spigot ends, suitable for push on Joints (Tyton Joint) each standard working lengths supplied with rubber gaskets duly ISI marked for water supply, Class K-9 with socket with "Push on Joint" supplied with ISI marked EPDM rube gasket conforming to IS-5382-1985 (Reaffirmed-2003) laid intrenches including taking up CI water mains complete all as specified and directed

S&F sluice valve the following sizes CI body ISI marked class PN 1.6 heavy duty flanged ends cast iron wheel with Brass spindle (ISI marked) conforming to IS : 14786 – 2000, short body including nuts ,bolt, washers and gasket including taking down of existing unserviceable sluice valve from the existing pipe line complete all as specified and directed:- ( Note: Quoted rate deemed to be included for making good the damaged valve chamber)

100 mm dia

150 mm dia

M&L for water pipe line route indicator duly engravd with "PIPE LINE MES" made out of pre-cast RCC (1:1.5:3) type A1 (using 12.5mm graded stone aggregates) of size 120 cm height 15cmx15cm cross section at bottom tapered to cross section 10cmx10cm at top duly reinforced with 4 Nos 10mm dia TMT main bars and 8 mm dia TMT bar as in stirrups @ 150mm c/c complete all as specified and directed. Note:- Excavation and PCC work shall be measured and paid seperately

Dismantling unserviseable existing water level indicator from Over head tank/underground reservoir/UG Sump under GE Saugor and S & fixing FRP scale conventional water level indicator as per site requirement complete with float,wire,float guide pipe,bracket & pulley,countor weight,indicator pin etc complete all as specified and directed Note : Qouted rate shall deemed to included to provide safety belt / ladder and insurance as required at site.

M&L for cutting of bituminous Road/floor/plinth protection for laying pipe not exceeding 1.5mm and 1.5 depth including refiling with excavated material and watering well ramming/compecting and making good with PCC 100 mm thick complete all as specified and directred by Engg-in-charge Note: PCC shall be measured and separately

Disconnecting and dismantling the existing motors, Control Panel and starters connection alongwith Suction & delivery water pipe line, foundation or MS frame etc from Outram Pump House complete all as specified and directed

M&L for PCC 1:3:6, type C-2 (using 40mm graded stone aggregates) as in filling mass concreat and making good distrubed surface all as specified and directed

M&L for PCC 1:2:4, type B-2 (using 40mm graded stone aggregates) as in filling mass concreat and making good distrubed surface all as specified and directed

M&L for PCC 1:2:4, type B-1 (using 20 mm graded stone aggregates) as in filling and making good ground surface all as specified and directed

M&L for reassembling the Motors with pump set, Motor control Starters and motor starter control panel, control wires and refixing the motor alongwith pump set from foundation or MS frame, realignment of the pump sets and suction and delivery pipes, connecting control wires with suitable lugs from main panel to control panel, panel to starter,starter to motor with protection of PVC pipe 40 mm dia with interval clamping, testing and commissioning complete all as site requirement complete all as specified and dircted by the Engg-in-Charge Note: PCC alongwith pipes shall be measured seperately

M&L for mild steel frame work made of 40mm x40mm x 5mm angle iron complete and top cover made out of 3.15 mm hick MS sheet duly hinged with frame including grouting / fixing into wall chamber and painting with two coats of enamell paint over a coat of red oxide and locking arrangement , lifting hook etc complete all as specified and directed

Material & Labour for repair of valve chambers by preparation of bricks surface including rendering 10mm thick in CM(1:4) on fair face of brick work complete all as specified and directed

M&L for construction of brick masonary valve chamber chamber of 1500mmx 1500mm x 1200mm size (inside) for sluice valve with CI wheel valve with bricks of subclass B in cement mortar 1 :4 (1 cement : 4 fine sand), 12mm thick, Inside plastering in cemtn mortar 1:4 finished with a floating coat of neat cement, foundation concreate in 1:4 :8 type D2 (1 cement : 4 fine sand : 8 graded stone aggregate 40mm nominal size) and with angle iron frame of size 40x40x5mm & 3mm thick MS Sheet cover, with locking arrangement including necessary excavation & earth work and valve door enamel painting & white washing of pit chamber complete all as specified and directed

All as per Srl item No. 24.00 here in before but size of 1200mm x 1200mm x1000 mm

All as per Srl item No. 24.00 here in before but size of 1000mm x 1000mm x 900mm

All as per Srl item No. 24.00 here in before but size of 900mm x 900mm x 900mm

Supply only following items complete all as specified and directed:-

CI Giffy Mechanical joint collar coupling suitable for CI/DI 80 mm dia pipe line as per sample

All as per Srl item No. 28.01 but 100 mm dia pipe line

All as per Srl item No. 28.01 but 150 mm dia pipe line

All as per Srl item No. 28.01 but 200 mm dia pipe line

All as per Srl item No. 28.01 but 300 mm dia pipe line

All as per Srl item No. 28.01 but 400 mm dia pipe line

All as per Srl item No. 28.01 but 450 mm dia pipe line

All as per Srl item No. 28.01 but 500 mm dia pipe line

CI Foot Valve 50 mm dia

CI Foot Valve 200 mm dia plunger type as per existing sample alongwitth suitable nut,bolts with double washers and gasket complete

CI Foot Valve 250 mm dia plunger type as per existing sample alongwitth suitable nut,bolts with double washers and gasket complete

All as per Srl item No. 28.11 here in before but 80 mm dia

Giffy Joint suitable for GI pipe 50 mm dia alongwith rubber "O"ring including Nut,bolts with washers

Giffy Joint suitable for GI pipe 80 mm dia alongwith rubber "O"ring including Nut,bolts with washers

Mechanical "T "Joint suitable for 100 mm dia alongwith Set of rubber ring and Bolt, nut with washers suitable for CI Pipe

All as per Srl item No. 28.15 here in before but 150 mm dia

All as per Srl item No. 28.15 here in before but 200 mm dia

All as per Srl item No. 28.15 here in before but 250 mm dia

All as per Srl item No. 28.15 here in before but 300 mm dia

All as per Srl item No. 28.15 here in before but 400 mm dia

All as per Srl item No. 28.15 here in before but 450 mm dia

All as per Srl item No. 28.15 here in before but 500 mm dia

MS flat not less than 80mm width and 5 mm thick clamp split type along with bolt,nut with washer including 15 mm dia socket duly welded top of the clamp suitable for 50 mm dia

MS flat not less than 80mm width and 5 mm thick clamp split type along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 80 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt, nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 100 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 150 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 200 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 300 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 350 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 400 mm dia

MS flat not less than 80mm width and 5 mm thick clamp along with bolt,nut with washer including 25 mm dia socket duly welded top of the clamp suitable for 450 mm dia

Bolt, nuts with double washers different length and sizes as per sample and as per requirment

Lead Pig

Rubber packing sheet 4 mm thick

Shellac bottle 50 ML

GI Socket 15 mm

GI Union 15 mm

GI Elbow 15 mm

GI Socket 20 mm

GI Union 20 mm

GI Elbow 20 mm

GI Pipe Nipple 15 mm dia 3" long

GI Pipe Nipple 15 mm dia 6" long

GI Pipe Nipple 15 mm dia 9" long

GI Pipe Nipple 15 mm dia 12" long

GI Pipe Nipple 20 mm dia 3" long

GI Pipe Nipple 20 mm dia 6" long

GI Pipe Nipple 20 mm dia 9" long

GI Pipe Nipple 20 mm dia 12" long

GI Pipe Nipple 25 mm dia 3" long

GI Pipe Nipple 25 mm dia 6" long

GI Pipe Nipple 25 mm dia 9" long

GI Pipe Nipple 25 mm dia 12" long

GI Tee Equal 15 mm dia

GI Tee Equal 20 mm dia

GI Tee Equal 25 mm dia

GI Socket reducer 20x15 mm

GI Socket reducer 25x15 mm

GI Socket reducer 25x20 mm

GI Barrel Nipple 15 mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

GI Barrel Nipple 20mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

GI Barrel Nipple 25 mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

GI Barrel Nipple 40 mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

GI Barrel Nipple 50 mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

GI Barrel Nipple 80 mm dia 300 mm long with full threaded alongwith two nos check nut as per sample

Iron cutter machine blade only as per sample

Brick machinery wall cutter machine blade only as per sample

Taking out the existing unserviceable Non return valve 450 mm dia ,S&F new Non return valve size of 450 mm dia CI body ISI marked heavy duty flanged ends all as specified including nuts ,bolt, washers and gasket all as directed by Engineer-inCharge. Note: Quoated rate deemed to include making good the damaged valve chamber complete all as specified and directed. Note: Excavationof earth work shall be measured and paid separately

M&L for excavation of soil up to 5cm root of the vegetation including cutting and removing e and surface dressing all around the water supply installations under GE Saugor area to keep the installation area (external only) clean and tidy complete all as specified and directed by Engineer -in-Charge. Note:- All the installation shall be kept clean through out the contract period by repeatedly removing the grasses/trees/ weads as many times as required depending on the growth of the grass

S&F in replacement glow sign board for E/M pump House installations with computerised words printed on PVC board (Matter and size of letters as approved by Engineer-in-Charge)including fabrication of work , angle iron, electrical connection with suitable copper wire and LED tube light fittings complete all as specified and directed

Repairs to leakeage/repairs and water supply break down by using JCB/Manual arrange sufficient manpower to arrest leakeage/break down including taking down and relaying of following size complete all as specified and directed by Engineer-in-Charge (Note Earth work/PCC/CI/DI specials shall be measurerd and paid separately) :-

80 mm bore

100 mm bore

150 mm bore

200 mm bore

250 mm bore

300 mm bore

400 mm bore

450 mm bore

500 mm bore

Opening the top of the sluice valve carefully, taking out the gate & spindle, scraping/cleaning the gate both sides, cleaning/scraping of sluice valve body throughly from inside, refixing / replacing the spindle, gate cheak nut and top of sluice valve including replacement of gland packing rope of suitable size & rubber gasket and Bolt,nut with washers necessary metalling ,grinding and levelling of the valve door seating complete for the following sizes of Sluice valve (Note:- Replacement of check nut/ spindle etc shall be measured and paid separately under relevant items) :-

80 mm bore.

100 mm bore.

150 mm bore

200 mm bore

250 mm bore

300 mm bore

350 mm bore

400 mm bore

450 mm bore

500 mm bore

Supply only spindle stainless steel suitable for following size CI sluice valve :-

80 mm bore.

100 mm bore.

150 mm bore

200 mm bore

250 mm bore

300 mm bore

350 mm bore

400 mm bore

450 mm bore

500 mm bore

Supply only sluice valve check nut CI as per sample (Square/rectangle) of following size :-

80 mm bore.

100 mm bore.

150 mm bore

200 mm bore

250 mm bore

300 mm bore

350 mm bore

400 mm bore

450 mm bore

500 mm bore

Taking down old corroded Sign boards of Frame MS pipe with MS Sheet of various sizes from the existing positions of different locations complete including making good the distrubed surfaces to match with the existing surfaces of the area in all respect all as specified and directed by Engineer-in-charge.

Supply, Fabricated and Polishing stainless steel board stand or frame of size SS heavy pipe 50 mm dia pipe work for fixing 'ACP' Sign board (Aluminium compost Panel) of size 1.6m x 1.3m , 3 mm thick with in the SS frame of size SS heavy pipe 20 mm dia pipe work and SS ball of dia not less than 50 mm on SS stand including writing details of installations/Machinery details etc with both side vinyl pasting on radium stricker letters complete all as specified an directed by Engineer-in-charge

Carry out Labortary analysis test of treated and untreatd drinking water Bactrological examination of standard plate count total coliform, Faecal Streptococcus and physical examination report to be submitted to departement as received from Labortary . Note: The Labortary test shall be carried out at Madhya Pradesh water and drainage board

Material & Labour for preparing the surface of valve pit chamber MS cover painting with one coat of syntheticenamel paint and with one coat over a painting over a surfae of existing colour including scapping out of Old fadded paint complete all as specified and as directed by Engineer-in-Charge

shubhanshu traders