REPAIR TO JOINERY CUPBOARD KITCHEN CABINET AND OTHER RELATED WORKS INCLUDING MAINT OF INTERNAL WIRING FITTING FIXTURES AND ALLIED WORKS AT ASC RPA FD WKS ANIMAL COY RANGPUR VIHAR BAGRA VIHAR UMRAO SINGH ENCLAVE OFFRS MESS AND OTHER U AREA OFGE SUKNA

Amount

M&L for Plain Cement Concrete Type D2 1:4:8 (using 40 mm graded stone aggregate) in foundations, filling and mass concrete complete all as specified and directed.

M&L PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in copings, bed plates, bed block for holdfasts, filling in pressed steel door frames, benching, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating and including necessary formwork complete all as specified and directed.

M & L for providing Reinforced cement concrete (1:2:4) type B-1 Nominal Mix using 20 mm graded stone aggregate as in slab supported on walls ,beams and coloumns in floors,roofs,landings, kitchen slabs etc complete all as specified and directed. (Note :- Reinforcement shall be measured and paid separately.)

Supply only liquid water proofing compound complete all as specified.

M & L for brick work with sub class ‘B’ old size bricks straight or curved on plan n.exc. 6.00 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for Brick work with sub-class `B' bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed.

Cutting chases, pinning in, making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, lintels, shelves etc, and cutting chases for concealed water tubing or concealed conduit wiring etc, and making good on brick walls, cutting not exc. 10 cm in girth complete all as specified and directed .

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

S & F of 2nd class Hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails sectional area exc 13 but not exc. 25 sqcm complete all as specified and directed.

S&F 2nd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including making rebate for fixing second shutter as per site requirement complete all as specified and directed.

S&F 30 mm thick flush door shutters solid core construction, with block board core and plywood face fanels, commercial type on both side and covered on both side with decorative face veneer with liping/frame to match complete all as specified and directed.

Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description not exceeding 1.0 Sqm each complete all as specified and directed.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete all as specified and directed.

Resecuring or easing and adjusting without taking down shutters of any description not exceeding not exc 1 sqm each leaf complete all as specified and directed.

Taking down shutters of any description exc 1.0 Sqm but not exc 2.0 Sqm and refixing in same opening complete all as specified and as directed.

All as per Sl item No 17 above but exc. 1.0 Sqm but not exc. 2.0 Sqm each.

S & F 30 mm thick (style thickness) factory made solid panel PVC shutter consisting of frame made out of mild steel tubes for top and bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles and rails with suitable PVC sheets beading and joined together with solvent cement as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of mild steel tubes for top & bottom rails, mild steel frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of wire gauze in lieu of plain colour PVC sheet. The wire gauze shall be wrapped on an additional square 8mm MS Solid tube and this tube shall be welded to MS tubes. The wire gauge shall be stretched to tighten firmly, suppling & fixing in the frame at site as per specification & drawing as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S & F factory made Solid PVC door frame of size 50 mm X 47 mm made out of 5 mm plain coloured PVC sheet reinforced with mild steel square tube as per specification and drawing given on MES schedule Part – II (2010) complete all as specified and directed.

S&F in repairs 5 mm thick PVC insulation panel with EPS stuck to 1 mm plain PVC sheet suitably placed in false ceiling including GI frame work for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9mm thick having equal flanges of 15mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (n. exc. 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel at 457 mm centre to centre and necessary hangers 6 mm dia GI fixed to roof complete all as specified and directed.

S&F 200 mm long aluminium, anodised, barrel tower bolt of extruded section and fixed complete all as specified and directed.

S&F 125mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S&F 75 mm long aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S&F 200 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F Continuous (Piano) hinges, brass, bright finished width of flaps (When open) 40 mm complete all as specified and directed.

S & F 75 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S&F brass knobs 35 - 40 mm dia complete all as specified and directed.

S&F in repairs Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width of and of weight between 61 to 80 Kg. (extruded section) complete all as specified and directed.

S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S&F in repairs Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

S & F Mild steel work in framed work such as grills, gratings, framed guard bars, ladders etc., with ends of bars shouldered and/ or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tank and similar work confirming to Fe-290 Gde E-165 Complete all as specified and as directed by Engr-in-Charge.

M&L for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

M&L for Mild steel TMT bars 5 mm to 10 mm dia.,cut to length, bent to shape required, in stirrups, spacers and binders and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips complete all as specified and directed.

S&F rolled mild steel in plates, gusset plate (plain or chequered) channels square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment conforming to Fe-410W (Gde-E-250) quality-A complete all as specified and directed.

S & F of structural steel work as in tubular trusses including special shaped washers etc. complete using ERW or induction butt welded tubes conforming to IS – 1161 – 1979 grade St – 240 including fabrication complete all as specified and directed.

S & F Steel windows with side hung shutters including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Steel windows with side hung shutters including box type hinges with steel handle, and steel peg stay, complete without glazing bars, dove-tailed or welded complete all as specified and directed.

S&F steel window or ventilator fixed type and including two pairs of brass cup pivots, catch spring and pulley wheels complete all as specified and directed.

S & F of pressed steel frame of size 105 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S & F of pressed steel frame of size 125 X 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc complete all as specified and directed.

S&F Powder coated aluminium frame work (minimum thickness of powder coating 50 micron) for doors, sliding window three track, ventilators with one or more rebates and including necessary joining cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading screws etc, complete all as specified and directed.

S&F for Aluminium powder coated door shutters, aluminium section weighing not less than 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges anodised alumnium snap beading, screws etc complete all as specified and directed.

S&F standard aluminium anodised section for window (sliding three track/two track/fixed or louvers type) and ventilator shutters, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing or gaskets for fixing glass, anodised aluminium snap beading, screws, anodised aluminium fittings such as locking arrangement , screws, plugs, handle, lock, roller nylon ball bearing etc, complete all as specified and directed. Note :- Glass and wire mesh shall be measured and paid separately under respective items.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm TCT (total coated thickness) of any colour having tensile strength of 550 Mpa as in roof covering cladding to wall etc, fixed with self tapping screws complete all as specified and directed.

S&F 3 mm thick cover fillets of standard hard board, 40mm wide, and fixing with screws complete all as specified and directed.

S&F in replacement 4 mm thick E-board (designer pattern) celing of size 60x60 cm, fixed or laid / inserted to with and including aluminium framework with screws in false ceiling (flat or sloping) of grid size 605 x 605 mm and with and including anodised aluminium snap grid with 25x25x1.5 mm thick Tee section and 38x25x2 mm thick angle for false ceiling Hangers with 6 mm dia. G.I. (length as required) adjusting level fixed to roof slabs/truss by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia 40mm long complete all as specified and directed including necessary dismantling of existing unserviceable ceiling boards of any thickness incl cover fillets complete all as specified and directed.

M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer’s instructions complete all as specified and directed.

M&L in repair 12mm thick, plywood grade BWR conforming to IS : 303 type BB fixed to screws to timber frame work as in shelves complete fixed in repair all as directed.

S&F in repairs 09 mm thick prelaminated particle board, interior grade, prelaminated both side with decorative choice lamination fixed with screw to timber / aluminium frame work complete all as specified and directed.

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, with edges of 5mm thick teak wood leaping fixed with screws to timber frame work complete all as specified and directed.

M&L machine cut kota stone slab flooring 20-25 mm (minimum) thick as in flooring laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab and including rubbing and polishing and laid over 20 mm thick screed bed in CM 1:6 complete all as directed.

M&L machine cut kota stone 20-25 mm (minimum) thick as in skirting, dado, riser of steps, plinth, etc, laid over and including 10 mm thick backing in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the stone and including rubbing / grinding and polishing & two nos groove cutting line complete all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in floor over and including 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L 50 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base footpath / hard standing / pavings / finished even and smooth complete all as specified and directed.

M&L 75 mm thick, PCC 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in plinth protection/path laid in alternate bays and construction joints to be given at every 3M interval and corners of buildings and filled with bituminous mastic or equivalent filler complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50 mm graded stone aggregate) as in flooring etc finished even and fair to receive floor finish complete all as specified and directed.

M&L Coloured glazed ceramic tiles 300x 450x 7 mm thick in vertical surfaces and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing with cm 1:4 complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc.0.06 sqm but n. Exc. 0.11 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.11 sqm but n. exc. 0.18 sqm, in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm thick in CM 1:6 finish even and rough complete all as specified and directed.

M&L Non Skid ceramic coloured tiles 7 to 8 mm thick (square / rectangular) area of each tile exc. 0.18 sqm but n. exc. 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including screed bed 15 mm in cement mortar 1:6 complete all as specified and directed.

M&L coloured vitrified heavy duty full digital paving tiles 10 mm thick (square/rectangular) polished, area of each tiles exc 0.11 sqm but not exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over including screed bed or bedding layer of mortar 15 mm thick for laying floor tiles in cement mortar 1:6 finished even and rough complete all as specified and as directed

M&L for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) including removing the rubbish off the premises complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and fair complete all as specified and directed.

M&L for rendering 15 mm thick in two layers 10mm and 5mm on other than fair faces of brick work or concrete surfaces in cement mortar 1:4 finished even and smooth using WPC compound in top layer complete all as specified and directed. Note:- WPC shall be measured and paid separatley.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for painting the new WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- Applying a thin layer of wall care putty to obtain smooth finish (c) Priming surface- Applying one coat of alkali resistant primer (d) Painting- Applying two coats of oil bound distemper.

M & L for painting the old WALL surface complete all as specified and directed as follows :- (a) Surface Preperation- Preperation of old plastered or previously untreated surfaces of wall. (b) Putty application- NIL (c) Priming surface- NIL (d) Painting- Applying one coats of oil bound distemper.

M & L for painting the new wall surface complete all as specified and directed as follows :- (a) Surface Preperation- Preparation of newly plastered or previously untreated surfaces of walls (b) Putty application- NIL (c) Priming surface- Applying one coat of cement base primer (d) Painting- Applying two coats of cement base paint.

S & F Sheet glass 3.0 mm thick, ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane glazed with putty or fixed with beads complete all as specified and directed.

S&F 4 mm thick plain Sheet glass, ordinary quality and glazing with oil putty or in rubber beading with one way film in squares exceeding 0.5 Sq.M in each pane complete all as directed by Engr-in-Charge.

Hacking out old broken glass (any thickness, size, quality or description) from steel/wooden frames or stones, concrete or brick surrounds glazed with oil putty or fixed with beads complete all as specified and directed.

M & L for painting the new wood surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of pink primer (c) Painting- Applying two coat of synthetic enamel paint.

M & L for painting the old wooden surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old wooden surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the old steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of old steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- NIL (c) Painting- Applying one coats of synthetic enamel paint.

M & L for painting the new steel surface complete all as specified and directed as follows :- (a) Surface preperation- Preperation of new steel surfaces of any description, not otherwise described over 10 cm width or girth (b) Priming surface- Applying one coat of red oxide primer (c) Painting- Applying two coats of synthetic enamel paint.

M&L preparation of New steel surfaces of any description, not otherwise described over 10 cm width or girth and including applying two coats of synthetic enamel paint complete all as specified and directed.

Taking up or down 15 mm dia steel tubing and connections, complete all as specified and directed.

Taking up or down 20 mm bore steel tubing and connections, complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F 20 mm bore galvanised steel water tubing medium grade and including necessary GI fitting (such as bends, elbows, tees etc. and fixed to wall / ceiling or laid in / on floor complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 500 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), including 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S&F in repairs rotational moulded polyethylene water storage tanks of 1000 Litres capacity, triple layered (cylindrical vertical with closed top) hoisted and fixed in position and including 20 mm dia nipple suitable for HDPE water tank (minimum weight 45 gm), 20 mm bore ball valves (minimum weight 210 gm) high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed to 20 mm bore pipe & locking with GI wire (to prevent monkey menace) to tank complete all as specified and directed.

S & F in repair 15 mm bore bib tap chromium plated, fancy type cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F as in repairs brass CP central hole basin mixture chromium plated 15mm bore with capstan head, screwed down high pressure with or without lettered "hot" or "cold with long scewed shanks and fly nuts screwed for iron pipe complete all as specified and directed

S&F in repair brass CP wall mixer with over head shower arrangement chromium plated 15 mm bore with capstan head, screwed down high pressure with or without lettered “hot’ or “ cold” with long screwed shanks and fly nuts, connecting legs and wall flanges screwed for iron pipe as complete all as specified and directed.

S & F 15 mm bore stop valve / angle valve fancy type, chromium plated, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions including CP nipple and socket complete all as specified and directed.

S&F in repairs PVC connections 15 mm size with PTMT nuts, of length 450 mm & suitable for hot water supply complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S & F of 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F of 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints fixed to walls complete all as specified and directed.

S & F 75 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) bends of any radius, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S & F 110 mm bore PVC (SWR) junction single, (single T) equal or unequal, fixed with cement solvent, with oval access door complete all as specified and directed.

S&F in repairs sink without drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 915 x 460mm bowl size 405 x 355 x 178 mm and including 32 mm waste pipe & coupling complete all as specified and directed.

S & F for in repairs Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F in repairs corner glass shelf assembly consisting of 5.5 mm thick sheet glass shelf, & side not less than 300mm with ABS chromium plate bracket guard complete all as specified and directed.

S&F in repairs PVC waste pipe for urinal / WHB 32 mm / 40 mm bore with one end with socket for WHB/urinal/sink etc complete all as specfied and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and directed.

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling of corrugated or semi corrugated Asbestos Cement (AC) sheets in roof covering complete all as specified and directed.

S&F drawer stainless steel telescopic channel of required length complete all specified and directed

S&F magic eye15mm dia steel body suitable for 35 to 40 mm th doors with all necessary fittings all as specified and direcetd by Engr-in-Charge

S&F magnetic catch of size not less than 40 x 15 mm suitable for cup board complete all as specified and directed.

S&F 75 mm Stainless steel butt hinges, fine grade steel soft close grinding welded head with single pin for lifetime durability, rust and corrosion proof suitable for any door, cabinets, windows and wardrobes etc.,complete all as specified and directed.

S&F in repairs 75 mm bore PVC (SWR) floor trap, plain with grating and including jointing with solvent cement complete all as specified and directed.

Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge.

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including non-metallic, rigid non mettalic PVC conduit (medium grade) concealed in wall / ceiling with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, modular plate and frame on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc. including all other fixing accessories for one light / fan / exhaust fan / call bell point controlled by one 5 / 6 Amps switch, all necessary cutting chasing (as required) and making good the disturbed surfaces including finishes to match with adjacent surfaces complete all as specified and directed. Note :- (i) Making good to match with the adjoining surface shall be included in the unit rate. (ii) Cutting chases shall be included in the unit rate.

All as per Sl. item No. 117.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on independent board.

All as per Sl. item No. 117.00 above but for point wiring modular plate one 5 / 6 Amps socket outlet point on same board.

All as per Sl. item No. 117.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per Sl. item No. 117.00 above but for one 16 Amps socket outlet point on independent board with 2.5 sqmm cable and 2.5 sqmm earth wire

M&L point wiring with 1.5 sqmm single core, PVC insulated, unsheathed FRLSH copper cable, 1100 volts grade, with multi stranded copper conductor drawn through and including PVC casing caping (double lock pattern) and accessories on wall / ceiling surfaces etc. with and including 1.5 sqmm single core PVC insulated, multistranded, unsheathed, FRLSH copper conductor cable as continuous earth continuity conductor (green in colour) with cast Iron / pressed steel terminal boxes 60 mm deep, on walls with 3 mm thick plastic laminated / hylam sheet cover, fixed on wall / other surfaces with brass screws for mounting or housing switches, socket outlets, fan regulators, etc including all other fixing accessories for one light / fan / exhaust fan point controlled by one 5 / 6 Amps switch complete all as specified and directed.

All as per Sl. item No. 122 above but for one 3 / 5 Amps socket outlet point on independent board.

All as per Sl. item No. 122.00 above but for one 3 / 5 Amps socket outlet point on the same board.

All as per Sl. item No. 122.00 above but for one light point controlled by two, 2 - way switches complete all as specified and directed

All as per item No. 122.00 here-in-before but one 3 pin socket outlet / 15 amps on the independent board with other switches, with cables 2.5 sqmm size complete all as specified and directed

M & L in replacement concealed sub main wiring with 2 runs of 2.5 sqmm main wire along with 1 run of 2.5 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 2 runs of 4.00 sqmm main wire along with 1 run of 4.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 2 runs of 6.00 sqmm main wire along with 1 run of 6.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

M & L in replacement concealed sub main wiring with 2 runs of 10.00 sqmm main wire along with 1 run of 10.00 sqmm earth wire (green in colour) single core FRLSH PVC insulated, unsheathed, multi-stranded, 1100 volts grade ISI marked copper conductor cable, drawn through and including adequate size rigid non-metallic PVC conduit (medium grade) with all fittings & accessories including cutting chases for conduits as required, sinking for terminal boxes, making good the disturbed surfaces including finishes to match with adjacent surfaces and including taking down complete all as specified and directed. NOTE:- Two runs of main copper conductor, one run of earth wire and one run of PVC conduit shall be measured as one unit length.

S&F switch piano flush type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano flush type one way, 15 Amps, 240 volt complete all as specified and directed.

S & F Switch piano 5 Amps single pole two way complete all as specified and directed.

S & F Socket outlet 5 Amps 3 pin flush type complete all as specified and as directed.

S & F Socket outlet 15 Amps 3 pin flush type complete all as specified and as directed.

S&F switch socket combination 2 in 1 , 3 pin , 6 and 16 amps flush type complete all as specified and directed.

S&F in replacement switch socket combination 5 pin 6 Amp, flush type universal complete all as specified and directed.

S & F in replacement Bell push, flush type, 5 Amps single pole complete all as specified and as directed.

S&F switch piano modular type one way, 5 / 6 Amps, 240 volt complete all as specified and directed.

S&F switch piano modular type one way, 15 /16 Amps independent, 240 volt complete all as specified and directed.

S&F switch piano modular type two way, 5 Amps independent, 240 volt complete all as specified and directed.

S&F modular type Bell push 6 A , 1 module complete all as specified and directed.

S&F socket outlet modular type 3 pin 5 / 6 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F socket outlet modular type 3 pin 15/16 Amps, 240 volts combined 2 modular complete all as specified and directed.

S&F MCB SP 6 to 32 Amp, 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB SPN 40 Amp , 10 kA, 240V 'C' curve complete all as specified and as directed.

S&F MCB TPN 40 to 63 Amp, 10 kA, 240V 'B' curve complete all as specified and as directed.

S&F in replacement MCB ,SPN DB, 08 ways double door, Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete including. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down switchgear with Dbcomplete all as specified and as directed

S&F in replacement MCB ,SPN DB, 12 ways double door,Metal door, IP-43 IK 09 in 100A rated bus bars,earth bar,neutral links complete incl. blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down switchgear with DB complete all as specified and as directed

S&F ceiling rose, surface bakelite 65 x 50 mm three terminal complete all as specified and directed.

S&F lamp holder, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings complete all as specified and as directed.

S&F stepped type electronic fan regulator two module, with 5 step, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in replacement stepped type electronic fan regulator two module, flush type, with 5 step, 450 W, AC 50 Hz 240 Volts grade complete all as specified and directed.

S&F in replacement Double door TPN DBs 4 Way, of powder coated DB's suitable for MCB's fitted with bus bar, neutral link, earth bar and Din ral & DB's will be fitted concealed in wall / surface as per site required including taking down switchgears with DB complete all as specified and directed.

S&F in repair VTPN DB,MCCB incomer,4 ways double door,Metal door ,IP-54 IK 09 in 250A rated copper bus bars,earth bar,neutral links, no. of module DPX 160 complete including blanking plates as required & fixed flush to wall and making good the disturbed surfaces including taking down old unsv ones complete all as specified and as direct. Make: Cat ref 507750 of Legrend/L&T or equivalent.

S&F MCCB 4 pole 125 Amps breaking capacity 25 KA, Ics = 100% Icu including spreader link complete all as specified and directed.

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 9 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR9WLED857S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 15 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR15WLED840S or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 18 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- edgeprosodlr18WLED840SG2 or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted square LED Downlighter with diffuser of 18 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- edgeprorddlr18WLED840SG2 or equivalent Make of Philips / Crompton .

S & F in repair recessed Mounted Round LED Downlighter with diffuser of 24 watt with WARM / WARM WHITE / WHITE LED elegantly designed sleek recessed mounted pressure die cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- ZIVAFLRDDLR24WLED857S or equivalent Make of Philips / Crompton .

S&F in repair Recessed Mounted Square (2'x2') LED Panel light 36 watt with CRCA powder coated housing & high transmittance Opal diffuser for glare free with Electronic independent electronic LED Driver inlcuding all fixing arragnement and electrically connecting from ceiling rose to light fitting complete all as specified and as directed. Make- Havells , Cat No- VENUSMOVE2X2PLR36WLED840SWH or equivalent Make of Philips / Crompton .

S &F Bell buzzer, Ding Dong AC. 230 volts, single pole completed all as specified and directed.

S & F in replacement Bell, AC. 230 volts, single pole completed all as specified and directed.

S & F in replacement Bell multi music type, AC. 230 volts, single pole completed all as specified and directed.

M &L in replacement Earthing with galvanised steel earth plate electrode 600 mm x 600 mm x 6 mm thick, buried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connected using galvanised iron earth lead wire 4 Sqmm as earthing electrode by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe (medium grade) and other end connected to earthing test point as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C both ways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth up to a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be made again by the contractor at no additional cost and including dimantling complete all as specified and directed.

S&F in replacement ventilation fan 200 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F in replacement ventilation fan 250 mm sweep, non metallic plastic body, AC single phase, 230 V, 50Hz with & including self closing louvres, nuts, screws, bolts of specified sizes, electrical connection with twisted three core PVC insulated unsheathed flexible cord of size 0.75 sqmm copper conductor from ceiling rose to exhaust fan and writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole writing MES number in 2 cm height with synthetic enamel paint and cutting wall for making hole and making good the disturbed surface to match the existing surface complete all as specified and directed. (Note-Old fan shall be deposited to MES storeyard without any extra cost.)

S&F in repair Metal Plug Socket DB with sheet metal enclosures with two pin and earth plug and socket one double pole MCB 20 Amps,240V for Geysor connenction complete all as specified and as directed. Make-Legrend/Anchor or equivalent.

S & F in repairs LED Bulk Head fitting 10 watt with Injection molded polycarbonate housing IP66, IK10, 3.5kV inbuilt surge protection, PF ≥0.95, total System Lumens not less than 1100 lm, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V. complete all as specified and as directed. Make- Havells , Cat No- RUGBYGENXFTS10WLED865SSYMBOPC or equivalent Make of Philips / Crompton .

S & F in repair Surface and wall mounted LED batten 10 watt 2 ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. Make- Havells , Cat NO- LUMILINEPLUSPROBS10WLED865SPCSSIND Or eqivalent Make of Crompton / Philips.

S & F in repair Surface and wall mounted LED batten 20 watt 4ft long with Aluminum housing & integrated Electronic Driver with IP20, PF 0.90, total System Lumens 1050 Lumens, 6500k CRI ≥ 80, Operating Voltage range 140 V - 270 V complete all as specified and as directed. Make-Havells,Cat NO- LUMILINEPLUSPROBS20WLED865SPCSSIND Or eqivalent Make of Crompton / Philips.

Supply and fix in replacement of LED driver for downlight of capacity 12W complete all as specified and directed.

Supply and fix in replacement of LED driver for downlight of capacity 15W complete all as specified and directed.

Supply and fix in replacement of LED driver for downlight of capacity 18W complete all as specified and directed.

Supply and fix in replacement of LED driver for downlight of capacity 24W complete all as specified and directed.

Supply and fix in replacement of LED driver for downlight of capacity 36W complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 100mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 175mm x 100mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 200mm x 150mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 250mm x 200mm x 50mm size complete all as specified and directed.

S & F in repair with for PVC rectangular block for mounting switches, sockets, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white), fixed in repairs complete of 350mm x 300mm x 50mm size complete all as specified and directed.

R N SAH N CO (BID ID -3448845)

MS ESSCON (BID ID -3449508)

MS ORIENT ENGINEERING WORKS (BID ID -3448804)

Janata Enterprises (BID ID -3448562)

D K SARKAR (BID ID -3449298)

ELECTRO WIR WAY (BID ID -3448756)

M/S GLORIOUS CONSTRUCTION (BID ID -3449240)