CONSTRUCTION OF NEW COURT BUILDING GROUND FLOOR Plus 4 FLOOR at DEVGAD, TAL. DEVGAD, DIST. SINDHUDURG.

Amount

Item No. 1 :- Excavation for foundation in earth, soils of all types, sand gravel and soft murum including removing the excavated materials upto a distance of 50 meters beyond the building area including all leads and lifts upto 1.5 metre, stacking and spreading as directed including dewatering, unless provided elsewhere preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete.

Item No. 2 :- Excavation for foundation in laterite rock (soft or hard) including trimming and levelling the bed for the foundation, removing the excavated material up to a distance of 50 metres beyond the building area, stacking as directed, dewatering and back filling with available murum, watering, ramming etc. complete. (Lift upto 1.5 m.).

Item No. 3 :- Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 metre).

Item No. 4 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). ( For Ground Floor )

For 1st Floor

4.02 For 2nd Floor

4.03 For 3rd Floor

Item No. 5 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the bottom surface and sides of excavation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area covering 10 years guarantee on bond paper.

Item No. 6 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) treatment by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of clorophyrifos per square metre of vertical surface area covering 10 years guarantee on bond paper.

Item No. 7 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Item No. 8 :- Providing preconstructional antitermite treatment as per I.S. 6313 (Part-I) to the soil along the external face of building by punching holes of 1.2 of 1.5 C.M. diametre about 30-60 cm. deep at 15 cm. c/c as close to the wall as possible and to inject 0.5 percent of aldrin or clorophyrifos at the rate of 7.5 litres per hole and sealing the same with proper filling and covering 10 years guarantee on bond paper.

Item No. 9 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 10 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

D) For 4th Floor

E) For 5th Floor ( Overhead Tank )

Item No. 11 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

E) For 5th Floor ( Overhead Tank )

Item No. 12 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

D) For 4th Floor

E) For 5th Floor ( Overhead Tank )

Item No. 13 :- Providing and laying Cast in situ/Ready Mix cement concrete M-35 of trap metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 14 :-Providing and laying Cast in situ/Ready Mix cement concrete in M-35 of trap metal for R.C.C. pardi of required thickness including centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

D) For 5th Floor ( Overhead Tank )

Item No. 15 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-35 of trap metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, plywood/ steel formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

D) For 4th Floor

Item No. 16 :- Providing and fixing during laying in RCC Slab rectangular 2 millimeter thick M.S. sheet fan hook box of size 180 x100 millimeter with required depth with holes or notches as required, bottom and top sides of 1.6 millimeter M.S. sheet fixed with 3.5 millimeter diameter round headed screws together with 12 millimeter diameter M.S. bar bent to shape with hooked ends for fan hook and painting to exposed surface etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 17 :- Providing and fixing in position TMT (Thermo Mechanically Treated) FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete. (For Ground Floor)

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

E) For 5th Floor ( Overhead Tank )

Item No. 18 :- Filling in plinth and floors with contractor's murum in 15 to 20 centimeter layers including watering and compaction as directed by Engineer-in-charge with all leads and lifts etc. complete.

Item No. 19 :- Filling in plinth and floors with approved excavated materials in 15 to 20 centimeter layers including watering and compaction as directed by Engineer-in-charge with all leads and lifts etc. complete.

Item No. 20 :- Providing dry trap rubble stone soling 15 centimeter to 20 centimeter thick including hand packing and compacting etc. complete. ( For Ground Floor )

B) For 2nd Floor

C) For 3rd Floor

Item No. 21 :- Providing laterite stone masonary in cement mortar 1:6 in foundation and plinth including striking joints on the unexposed faces and watering complete.

Item No. 22 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints where plastering is to be done watering , scaffolding with all leads and lifts etc. complete. (Laterite stone 6 sides cut and thickness of morter joints shall be 12 millimeter miximum) ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 23 :- Providing Autoclaved Aerated Concrete Block masonry of Ecolite or equivalent make conforming to IS:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to IS:6441 (Part I) - 1972) ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 24 :- Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. on cement mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing, etc. complete. ( Ground Floor )

A) For 1st Floor

A) For 2nd Floor

C) For 3rd Floor

Item No. 25 :- Providing and fixing in position Double shuttered aluminium extruded powder coated openable door of specified size with aluminium door frame of powder coated section 101.60 x 44.75 millimetre, 3.18 millimetre thick and shutter comprising of powder coated section having bottom and lock rail of size 150 millimetre x 44.5 millimetre x 3.00 millimetre thick top rails 47.62 x 44.45 millimetre x 3.00 millimetre thick , vertical style 47.62 x 44.45 millimetre, 3.00 millimetre thick and for shutter plain glass panes 5 millimetre thick for top panels and 12 millimetre thick both side laminated phenol bonded particle board panels for bottom panels etc., I.S.I. mark, heavy duty, Hydraulic floor spring of 150 kilogram capacity , having heavy duty concealed lock, necessary beading, glazing clips, PVC gaskets, 250 millimetre length aluminium tower bolts, 150 millimetre diameter pad handle, etc. as per detailed design and drawing or as directed by engineer in charge including all materials, labours, and equipment etc. complete. ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 26 :- Providing and fixing solid core flush door shutter in single leaf 32 millimeter thick decorative type of exterior grade as per detailed drawings approved face veneers 3 millimeter thick on both faces or as directed, all necessary beads, mouldings and lipping, wrought iron hold fasts, chromium plated fixtures and fastenings, with brass mortise lock, chromium plated handles on both sides, and finishing with French Polish etc. complete. ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 27 :- Providing and Fixing 30 mm. thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19 mm for styles and 15 x15 mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 mm (+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles ; and 5 mm thick ,95 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm (+/0.25) x 30 mm PVC sheet beading on either side and joined together with solvent cement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100 mm x 25MM x 2mm using 32 mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 28 :- Supplying and fixing in position Aluminium extruded section Four track sliding windows upto 1.2 metre height, outer frame made from section of over all size 80 millimetre x 45 millimetre, bottom section with or without drain section, track weighing 0.90 kilogram per metre and top and side section weighing 0.838 kilogram per running metre with shutter or sections made of 19 millimetre x 40 millimetre size having average weight of 0.6 kilogram per running metre (or as required size) with change in proportionate weight fixed with 5 millimetre thick High performance Single Glaze Unit (SGU) - Glass, new neoprene gasket shutters to be provided with nylon encased stainless rollers, necessary locks and handles complete. , and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 29 :- Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 millimetre at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 millimetre at weight 1.070 kg/Rmt. Top and side track section 92 x 31.75 x 1.30 millimetre at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 millimetre at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick High performance Single Glaze Unit (SGU) - Glass , and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour anodising without box. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 30 :- Providing and fixing in position anodised (as per IS 1868/1982) Aluminium fixed staggered ( Z Type ) Ventilator with aluminium rectangular pipe 63 mm x 38.10 millimetre x 1.22 millimetre at weight 0.650 Kg/Rmt, Aluminium angle of size 15 millimetre x 15 millimetre x 1 millimetre, aluminium channel of 9 millimetre sizes, S. S. mosquito net of 304 Grade, 4 millimetre thick float glass per detailed drawing and as directed by Engineer in charge etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 31 :- Providing and fixing in position aluminium fixed window fully glazed of any size as per detailed drawing and as directed by Engineerincharge with all necessary alluminium sections including necessary fixtures and fastening such as 5 mm thick clear float glass etc. complete. With Powder Coating ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 32 :- Providing and fixing mild steel grill work for windows, ventilators etc. 15 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 33 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 34 :- Providing internal cement plaster 6 milimeter thick in single coat in cement mortar 1:4 with neeru finish to concrete surface in all position including scaffolding and curing etc. with all leads and lifts etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 35 :- Providing internal cement plaster 12 millimeter thick in single coat in cement mortar 1:4 with neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 36 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 37 :- Providing and applying Texture plaster with finishing with Purlina/ Rustic texture material (with texture material of Asian/ Renava/ Nitco/ Temtex or equivalant company make) in 3 to 4 millimeter thickness on previously finished plastered surface including plaster Groove 6 millimeter thick or Tape Grooves 35 to 45 millimeter thickness or as required in all postion including preparing the surface scaffolding etc. complete. ( including texture Paint and Texture Paint Finishing) ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 38 :- Providing internal cement plaster 20 milimeter thick in single coat in cement mortar 1:3 without neeru finish to stone masonry surface in all positions including scaffolding and curing with all leads and lifts etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 39 :- Providing internal cement plaster 20 milimeter thick in two coats in cement mortar 1:5 without neeru finish to concrete, brick surface in all positions including scaffolding and curing with all leads and lifts etc. complete.

Item No. 40 :- Providing fine cement finish 1.5 millimetre thick over green plaster surface including scaffolding curing etc. complete. ( Gr

Item No. 41 :Providing and laying Vitrified Matt finish tiles having decorative type tiles of size 895 to 900 millimeter x 895 to 900 millimeter of 10 to 12 millimeter thickness confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 42 :-Providing and laying vitrified Matt finish tiles having size 590 millimetre to 605 millimetre x 590 millimeter to 605 millimeter of 8 to 10 millimeter thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for Dado and Skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete. ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 43 :- Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 curing and cleaning etc. complete ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 44 :Providing and laying Vitrified Matt finish tiles having decorative type tiles of size 895 to 900 millimeter x 895 to 900 millimeter of 10 to 12 millimeter thickness confirming to IS 15622-2006 (Group Bla) of approved make shade and pattern for flooring in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete.

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 45 :-Providing and laying vitrified Matt finish tiles having size 590 millimetre to 605 millimetre x 590 millimeter to 605 millimeter of 8 to 10 millimeter thickness and confirming to IS. 15622-2006 (Group Bla) of approved make, shade and pattern for Dado and Skirting in required position laid on a bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning. etc. complete. ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 46 :- Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centimetre x 30 centimetre and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 47 :- Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness and size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 millimetre thick compacted bed of fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer specifications and direction of Engineer-in-Charge. 60 millimetre thick Cement Concrete paver block of M-35 grade concrete with approved colour and design and pattern.

Item No. 48 :- Providing and fixing on walls/ ceiling/ floor 15 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 49 :- Providing and fixing on walls/ ceiling/ floor 20 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 50 :- Providing and fixing on walls/ ceiling/ floor 25 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 51 :- Providing and fixing on walls/ ceiling/ floor 32 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 52 :- Providing and fixing on walls/ ceiling/ floor 50 millimetre diametre Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete.

Item No. 53 :- Providing and fixing screw down for 15 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 54 :- Providing and fixing Chromium Plated 2 Way BIB cock with wall flange of approved make including necessary sockets/ union nut etc. complete as directed by Engineer in charge. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 55 :- Providing and fixing screw down for 32 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Item No. 56 :- Providing and fixing screw down for 50 millimetre diameter wheeled stop tap of brass including necessary sockets/union nut complete.

Item No. 57 :-Providing and fixing Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195 millimetre size with pillar cock, Chromium Plated Angular stop cock, long thread of approved make continental including Stainless Steel bottle trap of necessary pipe connection up to the outside face of the wall, having Telephonic Black / Colour Granite of 180 millimetre thick fixed on Black Kadappa Framework, etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 58 :- Providing and fixing Jaquar or equivalent make wall hung white wash basin of size 470 x 575 x 190 millimetre - code no. OPSWHT-15801, with Jaquar or equivalent make half pedestal, code no. OPS-WHT-15305 with Jaquar or equivalent make pillar cock, code no. CON-021KN / 021KN G / 021KN GA / 021KN GB / 021KN GD, C. P. Angular stop cock long thread jaquar or equivalent make continental (Cat.No. CON-059) including Stainless Steel bottle trap of jaquar or equivalent make having code no. ESS-773 NB and necessary pipe connection up to the outside face of the wall etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 59 :- Providing and fixing white glazed earthenware sink 600 millimetre x 200 millimetre x 450 millimetre including all connection of the galvanised iron supply and Poly Vinyl Chloride waste pipes up to the outside face of the wall, cold water chromium plated screw down bib tap, rolled steel or Cast Iron brackets, rubber plug with chain and stop tap complete. ( Ground Floor )

A) For 2nd Floor

Item No. 60 :- Providing and fixing sink cock with regular swinging spout ( Wall Mounted Model ) with wall flange with approved make incluidng other necessary fitting, etc. complete as directed by Engineer in charge. ( Ground Floor )

A) For 2nd Floor

Item No. 61 :- Providing and fixing 10 centimeter Poly Vinyl Chloride nahani trap with grating etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 64 :- Providing, constructing and fixing Supreme make or equivalent make Ultra 250 millimetre diametre Inspection chamber made up of UPVC material of thickness 3.5 millimetre and height of 259 millimetre with inlet and outlet of 110 millimetre diametre with 75 millimetre diametre U Trap, Ultra shaft pipe of Upvc material having height of 470 millimetre and fixing Ultra 250 millimetre diametre UPVC cover and frame in 150 millimetre thick in cement concrete1:2:4, having crushed sand bed of 100 millimetre thick of size 550 millimetre diametre. Including excavation and refilling the sides of chamber by crushed sand cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No. 65 :- Providing , constructing and fixing Supreme make or equivalent make Ultra 450 milimetre diametre Inspection chamber made up of Polypropylene / polyethylene material of thickness 3.5 millimetre and height of 388 millimetre with 160 or 200 millimetre main inlet (s) outlet and 110 and / or 160 millimetre branch inlets, with 450 millimetre diametre Ultra shaft pipe of HDPE material having height of 460 millimetre, having Reinforced Cement Concrete cover and frame fixing in 150 millimetre thick in cement concrete 1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diametre. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No. 66 :- Providing , constructing and fixing Supreme make or equivalent make Ultra 600 milimetre diametre Inspection chamber made up of Polypropylene / polyethylene material Having 315 millimetre diameter inlet(s)/outlets and with eccentric reducers as per requirement to connect 160 millimetre and 200 millimetre pipes having thickness of 5 millimetre and 600 millimetre in height, with inbuilt shaft achieve the invert depth as per site condition of wall thickness of 5 millimetre having Reinforced Cement Concrete cover and frame fixing in 150 millimetre thick in cement concrete 1:2:4, having crushed sand bed of 150 millimetre thick of size 750 millimetre diametre. Including excavation and refilling the sides of chamber by sand crushed cushioning 150 millimetre thickness, connecting all required UPVC fittings with rubber lubricant etc. complete.

Item No. 67 :- Providing soak pit of size 120 centimeter x 120 centimeter x 120 centimeter including excavating and filling with brick-bats etc. complete.

Item No. 68 :- Providing and fixing 450 millimeter x 550 millimeter size superior type Belgium mirror with 16 millimeter diameter nickel plated towel rod etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 69 :- Providing and fixing chromium plated towel rod 16 millimeter diameter and 75 centimeter in length including all accessories complete. ( Ground Floor ) (for toilets)

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 70 :- Providing and fixing machine cut mirror polished 18 millimetre to 20 millimetre thick telephone black granite / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone partition with rounding / moulding the edges etc. complete. Both side polish. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 71 :- Providing and fixing H.D.P. container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 1000 to 20,000 litres.

Item No. 72 :- Providing and fixing P.V.C. Rain water pipes of 160 millimeter outer diameter and having wall thickness of 2.2 to 2.7 millimeter confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number ,filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on C.C. or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete. (The contractor shall give 3 yrs guarantee bond for payment) ( BRAND FINOLEX / SUPERME / PRINCE) ( For Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 73 :- Providing and fixing 75 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. ( BRAND FINOLEX / SUPERME / PRINCE) ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 74 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete. ( BRAND FINOLEX / SUPERME / PRINCE) ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 75 :- Providing and fixing white European type wall-hung, of size 360 mm. x 360 mm x 575 mm with approved make flush valve including soil pipe, vent pipe upto outside face of wall, 100 millimetre diametre Cast Iron plug bend inlet pipe all fittings, cutting and making good walls, floors etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 76 :- Providing and fixing Orissa Pan of size 580 x 445 x 260 millimetre with approved make flush valve including trap, C.I. soil and vent pipe upto outside face of wall including 100mm dia. C.I. plug, bend and necessary pipe connection, etc complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 77 :- Providing and Fixing mat finish stainless steel (of 302 grade ) railing with top pipe of 50 millimetre diametre and vertical pipe of 38 millimetre diametre at 0.60 metre c/c or as required and horizontal pipes of 25 millimetre diametre in three rows, all pipes of 2 millimetre thick including buffing,fabricating fixtures and fastening including pipe base of appropriate diameter and ball base of 75millimetre diametre above newel post of 75 millimetre diametre etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 78 :- Providing and fixing 40 milimeter diameter and 1.5 milimeter thick Stainless steel hand railing in S.S. 304 grade including fabricating, fixtures, errecting necessary welding, grinding, finishing, buffing to stainless steel pipe etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 79 :- Providing and fixing 45 centimeter wide steel ladder of 40 x 6 milimeter mild steel flat stringers and steps of 18 milimeter diameter mild steel bar including fixing it in M-15 cement concrete block 60 x 30 x 30 centimeter and painting the ladder with antirust primer and two coats of oil painting including all leads and lifts etc. complete.

Item No. 80 :- Providing and fixing white glazed Jaquar or equivalent make urinal of series URS-WHT-13257 with Pressmatic auto closing valve of Jaquar or equivalent make having code PRS-077G, 32 millimetre diameter P.V.C. flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap and soil pipe connection upto the outside face of wall etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 81 :- Providing and fixing White Glazed Earthenware Squatting plate (Ladies Urinal) with P.V.C. flushing cistern of 5 liters capacity with fitting, inlet pipes and stop tap, brackets for fixing the cistern, 32 milimetre diametre P.V.C flush pipe with fittings and flushing arrangement including lead soil pipe, lead trap, soil pipe connectionup to the outside face of the wall. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 82 :- Providing and laying in position flooring of telephone black / Amba White / Cat bary brown / Ruby red / Ocean Brown granite stone of approved shade and size 18 mm to 20 mm thick on bed 1:6 cement mortar including cement floats striking joints, pointing in cement mortar 1:3 including leather finish to receive rough matt finish curing and cleaning etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 83 :- Providing and fixing machine cut machine polished 18 millimetre to 20 millimetre thick telephone black / Amba White / Cat bary brown / RBI red / Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with rounded moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 84 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting, curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). ( Ground Floor ) D) For 4th Floor

Item No. 85 :- Providing and fixing Jaquar or equivalent make series Hand shower (health faucet) with 8 millimetre diametre 1 Meter long flexible tube having code no. - ALD- / 573 GD / 537 GA / 573 GB and wall hook including necessary sockets/ union nut etc. complete as directed by Engineer in charge etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 86 :- Providing and fixing Jaguar or equivalent make Shower Head OHS-CHR-35497 / 35497 GD / 35497 GA / 35497 GB, with Jaquar or equivalent make shower arm code no. SHA-49483, Jaquar or equivalent make shower tube code no. SHA-549 D12, Jaquar or equivalent make hand shower code no. HSH-1937 / 1937 GD / 1937 GA / 1937 GB, with Jaquar or equivalent make divertor of code no. ALD-079 and FLR-5079K with Jaquar or equivalent make spout code no. SPJ-5463 / 5463 G / 5463 GA / 5463 GB / 5463 GD / 5463 GE, including all necessary pipe fittings and connections etc. complete as directed by Engineer in charge etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 87 :- Providing expansion joints in Reinforced Cement Concrete framed structure (interior column) with plain premoulded filler with confirming to IS : 1838-1961, 25 millimetre thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 88 :- Providing expansion joints in Reinforced Cement Concrete framed structure (exterior column) with plain premoulded filler 25 millimeter thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 89 :- Providing expansion joints in Reinforced Cement Concrete framed structure (at floor level) with premoulded filler 25 millimeter thick with 75 millimetre wide and 1 millimetre thick stainless steel plate finishing as directed etc. complete.

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 90 :- Providing expansion joints in Reinforced Cement Concrete framed structure (at terrace level) with premoulded filler 25 millimeter thick with 40 millimetre wide and 1 millimeter thick stainless steel plate as required, bituminous poured filler and finishing as directed etc. complete.

Item No. 91 :-Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (including the primer coat) etc. complete.

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 92 :- Providing and applying 2 Coats of 100% Pure acrylic water based paint with special heat reflectance property to withstand the harsh climate for period of atleast 10 years of approved make. Paint system should provide durable and long lasting finish with DFT of min 90 microns and should protect against concrete carbonation with R value of minimum 600 and equivalent concrete layer thickness value of min 150 centimetre. Paint should have breathability property and should be able to cover hairline cracks in the surface upto 0.5 millimetre. The paint has to be applied on a coat of high quality acrylic copolymer based alkali resistant primer with excellent penetrating properties including cleaning, with all leads and lifts at all levels etc. complete, as directed by Engineer in charge. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 93 :- Providing and fixing 90 centimetre x 60 centimetre Granite plate engraving 10 centimetre height letter, figures including painting the lefters/figures with approved colour and shade complete.

Item No. 94 :- Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete. ( For Ground Floor )

B) For Third Floor

Item No. 95 :- Providing & Supplying corrosion inhibiting admixture in concrete to protect steel bars for all concrete in every part Polyalk CP 293 of approved make & approved by Engineer in charge migrating, non-nitrite based corrosion inhibiting admixture shall be added at a dose of 3 Kilograms per cum of concrete. The admixture should protect both cathodic and anodic sites and have been accredited by Indian Roads Congress, recommended for use by Ministry of Road Transport & Highways and should have a 4 year track record of use in both the Gulf Region and India. Admixture should have evaluated test reports demonstrating a corrosion rate of zero coulombs after 9 test cycles as per ASTM G 109 when tested from a research institution NBA accredited Grade A and internationally ranked among top 5 research institutions in the world in Annual Survey conducted by Georgia Institute of Technology ranking of research institutions. PH of admixture should be alkaline in nature, specific gravity of 0.99 – 1.1, colour : brownish. The contractor must intimate the engineer in charge prior to addition in concrete for recording. If the admixture is put in the concrete mix at the batching plant, a written record of the amount of admixture used shall be supplied to the engineer. The engineer must ensure that the specified dosage of admixture is added in the concrete mix. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

D) For 5th Floor

Item No. 96 :- Providing and fabricating Galvanised Iron Sheet box 100 x 300 millimetre in size made by CP square pipe 40 millimetre size and covered by Alluminium Alloy plate 2 millimetre thick including cutting, welding and fixing in position etc. complete.

Item No. 97 :- Providing and applying two coats of synthetic enamel paint of approved colour to new structural steel work and wood work in buildings, including scaffolding if necessary cleaning and preparing the surface including primer coat etc. with all leads and lifts etc. complete.

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 98 :- Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance and thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strictly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- charge. ( Ground Floor )

Item No. 99 :- Providing and fixing chicken mesh of 22 gauge, with about 30 centimeter width at the junction of Reinforced Cement Concrete members and brick work, of approved quality including fixing mesh in position by necessary drilling in concrete /Burnt Brick masonry and or tying by binding wire etc. complete. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 100 :- Providing and fixing in position U.P.V.C. (Unplasticized Poly Vinyl Chloride) having multi-chambered outer frame section (73 x 50) millimetre with an outer wall thickness of 2 millimetre and steel reinforcement, multichambered slider frame (73x 60) millimetre with steel reinforcement, multichambered slider sash (46x 82) millimetre with steel reinforcement designed to give optimum strength, 5 millimetre thick toughened double glass with 12 millimetre spacer of good quality including alluminium track, Inter-locking profile, coextruded beadings, EPDM gaskets, silicon sealent, sliding handle, fixtures and fastenings (couplings, hinges) including with all required screws and nuts with all necessary U.P.V.C. sections as per the detailed drawing and as directed by Engineer-In- harge etc. complete.

A) For 1st Floor

Item No. 101 :- Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete. A) For 2nd Floor

B) For 3rd Floor

Item No. 102 :- Providing and constructing granite kitchen platform with fixing of stainless steel sink 600 millimetre x 450 millimetre size as per detailed drawing including vertical both side polished kadappah stone 25 to 30 millimetre thick supports with kadappah top 35 to 40 millimetre thick and polished granite 16 to 20 millimetre top with side strips of granite at front and both sides of platform raised with two vertical granite supports 15 centimetre height and top granite of 75 x 40 centimetre including cutting, opening for sink of required size in kadappah as well as granite etc. complete. (Platform top size 5.00 metre x 0.60 metre and height is 0.75 metre)

Item No. 103 :- Providing and fixing teak wood hand rail of 60 mm. x 75 mm. as per detailed drawings or as directed by the Engineer, including french polishing, etc. complete. A) For 2nd Floor

B) For 3rd Floor

Item No. 104 :- Providing and laying for 150 millimetre diametre salt glazed stoneware pipe including fittings Such as bends, tees, single junction, double junctions laying, jointing (including excavation and refilling the trenches) complete.

(A) First floor

(B) Second floor

(C) Third floor

Item No. 106 :- Providng and fixing in position Galvanised Iron Pipe 50 millimetre diametre (Heavy Type).

Item No. 107 :- Providing and applying interior wall finish luster of approved make on internal wall surface as detailed below Scrapping the surface with emery paper and wipe clean wall primer with brush with mineral turpentine with brush 8 to 10% and oil 15 to 20% with roller and allowing to dry for a period 6 to 8 hours. wall putty with appropriate proportion of water allowing to dry for period 4 to 6 hours. Scrapping with Emery paper 180 and wipe clean. Applyingwall primer with brush with mineral turpentine 8 to 10% and oil 15 to 20% with roller Scrapping Emery paper 320 and wipe clean, interior wall finish luster 1st coat with brush/rubber/spray with mineral turpentine 7 to 9% and Oil with roller 19 to 21% After 8 hours of activity Applying 2nd coat or wall finish Lustre with mineral turpentine 7 to 9 % with brush and Oil with roller 19 to 21% after allowing dry for the period of 6 to 8 hours activity. ( Ground Floor ) (A) First floor

(B) Second floor

(C) Third floor

Item No. 108 :- Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc. complete. ( Ground Floor ) (A) First floor

(B) Second floor

(C) Third floor

Item No. 109 :- Grab bars - Providing SS grab bars set for accessible toilets comprising of 4 nos. Grab bars as specified below. (1 nos. wing grab bar + 1 nos. L shaped grab bar + 2 nos. straight grab bars = 1 typical set) 27a) Swing grab bar (1 NOS) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 NOS) Providing S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM (D) and 32MM DIA. and thickness mm of the approved brand and make. 27c) Straight grab bar (2 NOS) Providing S.STEEL 304 GRAB RAIL (600 MM),32MM DIA. and thickness 1.5mm of the approved brand and make. ( Ground Floor )

A) For 1st Floor

B) For 2nd Floor

C) For 3rd Floor

Item No. 110 :- Removing Manglore tiled roof and ridge tiles with battens, ridge and barge boards, eaves 8 A boards etc. and sacking the materials as directed with all leads and lifts complete.Including removing wood work below etc. complete.

Item No. 111 :- Removing double country tiled roof with ridge and with battens and stacking the materials as directed with all leads and lifts, complete including removing wood work below etc. complete.

Item No. 112 :- Removing doors and windows with frames and stacking the materials as directed with all leads, lifts etc. complete.

Item No. 113 :- Dismantling flat wooden or A.C. Sheet ceiling with frame work including stacking the materials as directed with all leads, lifts etc. complete.

Item No. 114 :- Dismantling stone masonry in lime or cement mortar including stacking the materils as directed with all leads, lifts etc. complete.

Item No. 115 :- Removing ventilators and small windows with frame and stacking the materials with all leads, lifts etc. complete.

Item No. 116 :- Dismantling the R.C.C. Work 1:2:4 and sorting out the materials such as steel etc. as directed and stacking them within the specified lead as directed etc. complete.

Item No. 117 :- Removing battens from roof and stacking them as directed with all leads and lifts etc. complete.

Item No. 118 :- Removing W.C. pans including disconnecting the sanitary and water supply connections, removing and breaking flooring and bed con-crete around pan removing the same carefully and stacking the serviceable materials as adn where directed including throwing the unserviceable materiasls out side etc. carefully and throwing out the refusal outside etc. complete.

Item No. 119 :- Supplying Unskilled Heavy Male Labour. (for toilets)

Item No. 120 :- Supplying Hydraulic Excavator.

Item No. 121 :- Supplying Tipper.

Item No. 122 :- Excavation for foundation in earth, soils of all types, sand gravel and soft murum including removing the excavated materials upto a distance of 50 meters beyond the building area including all leads and lifts upto 1.5 metre, stacking and spreading as directed including dewatering, unless provided elsewhere preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete.

Item No. 123 :- Excavation for foundation in Hard rock by blasting including trimming and leveling the bed by chiseling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres from the building area including dewatering and back filling with available earth/murum, watering, ramming, etc. complete. (Lift upto 1.5 metre).

Item No. 124 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC without SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc).

Item No. 125 :- Providing laterite stone masonary in cement mortar 1:6 in foundation and plinth including striking joints on the unexposed faces and watering complete.

Item No. 126 - Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints where plastering is to be done watering , scaffolding with all leads and lifts etc. complete. (Laterite stone 6 sides cut and thickness of morter joints shall be 12 millimeter miximum)

Item No. 127 :- Providing and laying Cast in situ/Ready Mix cement concrete M-15 of trap metal for coping to plinth or parapet, moulded or chamfered as per drawing or as directed including steel centering, plywood/ steel formwork compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.) With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc).

Item No. 128 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 mm thick in cement mortar 1:4 using waterproofing compound at 1 kg per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 mm thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No. 129 :- Providing and fixing 50 millimetre diametre medium class Galvanised Iron pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in cement concrete block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Item No. 130 :- Providing and applying two coats of synthetic enamel paint of approved colour to new structural steel work and wood work in buildings, including scaffolding if necessary cleaning and preparing the surface including primer coat etc. with all leads and lifts etc. complete.

Item No. 131 :- Supplying 80 millimetre laterite stone metal at the road side for metal including conveying and stacking etc. complete ( 50 metre inital lead ) Hand Broken from boulders (excluding royalty)

Item No. 132 :- Supplying 60 millimetre laterite stone metal at the road side for metal including conveying and stacking etc. complete. ( 50 metre inital lead ) Hand Broken from boulders (excluding royalty)

Item No. 133 :- Supplying hard murum/ kankar at the road site, including conveying and stacking complete.

Item No. 134 :- Spreading 80/40 millimetre metal for road work including sectioning etc. complete.

Item No. 135 :- Spreading hard murum/ soft murum/ gravel or kankar for side width etc. complete.

Item No. 136 :- Compacting for 80 millimetre laterite metal layers with power roller including necessary labour materials and artificial watering complete.

Item No. 137 :- Compacting for 60 millimetre laterite metal layers with power roller including necessary labour materials and artificial watering complete.

Item No. 138 :- Providing and constructing 75 millimetre thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 millimetre stone metal layers 100% crusher broken metal with conical crusher plant heating and spraying the bitumen of specified grade @ 2 kilogram / square metre, spreading 12 millimetre size chips compacting with three wheel static roller having weight 8 to 10 Metric Ton to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete. Including picking of existing WBM surface.

Item No. 139 :- Open Graded Premix Surfacing- Providing and Laying OGC 20 millimetre thickness composed of 13.2 millimetre to 5.6 millimetre aggregates premixed with bituminous binder transported to site with VTS , laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired compaction, including tack coat at the rate 2.50 kilogramme per 10 square metre. For Bitumen VG-30 bulk—USING drum mix type hot mix plant with SCADA, Paver and Vibratory roller. ( Over M. P. M. surface )

Item No. 140 :- Providing bituminous Type A liquid seal coat on bituminous surface including supplying all materials and bitumen of VG-30 grade preparing existing road surface, heating and applying bitumen @ 0.98 kilogram / Square Metre by mechanical means, spreading chips and rolling, by static roller having weight 8 to 10 Metric Ton etc. complete.

Item No. 141 :- Providing and laying cement concrete pipe of IS 458:2003 NP-2 class of 900 millimetre diameter in proper line, level and slope including providing and fixing collars in cement mortar 1:2 and curing etc. complete.

Item No. 142 :- Providing and fixing Cautionary/Warning sign boards in Equilateral Triangle size of 600 millimetre made out of 3 millimetre aluminum composite material (ACM) sheet bonded with white retro reflective sheeting of Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3 Supported with back support frame 25 mm. x 25 mm. x 3 mm., duly painted on back side with grey stove enamel paint and supported on one no. of M. S. angle iron post of size 65 mm. X 65 mm. X 6 mm., 3.45 m. long, duly painted with with flat oil paint having alternate black and white bands of 25 cm. width including G.I. fixtures etc; fixing the boards in M-25 grade concrete block of size 60 cm. X 60 cm. X 75 cm. including transportation etc; complete. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. 600 millimetre made out of 3 millimetre aluminum composite material with 0.25 millimetre skin thickness on either side.

Item No. 143 :- Excavation for foundation in earth, soils of all types, sand gravel and soft murum including removing the excavated materials upto a distance of 50 meters beyond the building area including all leads and lifts upto 1.5 metre, stacking and spreading as directed including dewatering, unless provided elsewhere preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete.

Item No. 144 :- Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 metre).

Item No. 145 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). ( For Ground Floor )

Item No. 146 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 147 :-Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap metal for R.C.C. pardi of required thickness including centering, formwork, cover blocks, laying/pumping, compacting and roughening them if special finish is to be provided and curing complete.(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 148 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 149 :- Providing and fixing in position TMT (Thermo Mechanically Treated) FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No. 150 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No. 151 :- Providing and fixing 50 millimetre diametre medium class Galvanised Iron pipe gate with wicket gate of approved drawing with all fixtures and fittings in two leaves with strong hold fast embedded in cement concrete block at top and bottom with locking arrangement including cutting, bending, making holes and with one coat of primer etc. complete.

Item No. 152 :- ABC POWDER MAP 50, CAPACITY 9 Kg. Providing 9 Kg. Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge Gross Weight 13.8 Kg., Empty weight 4.8 Kg., Can Height : 611 mm., Diameter 175 mm., Discharge Time : Less than 18 Secs., Controllable discharge mechanism, Range minimum 4 metres, applicable on Class ABC and electrically started Fire, A Rating 21A, B Rating 89B Can Construction : Deep drawn and Co. Mig welded, Valve construction : Forging and Machining, Internal Coating of Can : Epoxy powder coating, External Coating of Can : Epoxy Polyster powder Coating, Sheet metal Thickness : 1.60 mm. , ISI and EN Approved etc. complete.

Item No. 153 :- ABC POWDER MAP 50, CAPACITY 9 Kg. Providing 4 Kg. Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge Gross Weight 6.9 Kg., Empty weight 2.9 Kg., Can Height : 435 mm., Diameter 140 mm., Discharge Time : Less than 9 Secs., Controllable discharge mechanism, Range minimum 4 metres, applicable on Class ABC and electrically started Fire, A Rating 13A, B Rating 55B Can Construction : Deep drawn and Co. Mig welded, Valve construction : Forging and Machining, Internal Coating of Can : Epoxy powder coating, External Coating of Can : Epoxy Polyster powder Coating, Sheet metal Thickness : 1.60 mm. , ISI and EN Approved etc. complete.

Item No. 154 :- ABC POWDER MAP 50, CAPACITY 9 Kg. Providing 6 Kg. Fire Extinguisher Mono Ammonium Phosphate Powder 50, Stored Pressure Type, Pressure Gauge Gross Weight 9.5 Kg., Empty weight 3.5 Kg., Can Height : 435 mm., Diameter 160 mm., Discharge Time : Less than 9 Secs., Controllable discharge mechanism, Range minimum 4 metres, applicable on Class ABC and electrically started Fire, A Rating 21A, B Rating 89B Can Construction : Deep drawn and Co. Mig welded, Valve construction : Forging and Machining, Internal Coating of Can : Epoxy powder coating, External Coating of Can : Epoxy Polyster powder Coating, Sheet metal Thickness : 1.60 mm. , ISI and EN Approved etc. complete.

Item No. 155 :- Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 Square Meter made out of 2 millimetre aluminum sheet bonded with white retro reflective sheeting of Class C ( Type IV High intensity micro-prismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier.

Item No. 156 :- Providing erecting and giving test of submersible pump set conforming to IS 8034 and motor conforming to IS 9283, with water proof winding. Pump shall be suitable for various delivery head and discharge with stainless steel shaft. Motor suitable for working on 415V +10%, 3 Ph, 50 Hz A. C. Supply, ith cable guard, thrust carbon / fiber bearing to withstand entire hydraulic thrust. The pump set shall be suitable for direct coupling, with suitable suction strainer. Pump should have suitable discharge out let as per manufacturer's design. Antithrust stream lined non return valve shall be provided with the pump. 3 m. submersible copper conductor cable in single / double run and 2 pairs of suitable size erection clamp 10 mm. thick shall be provided with each pump.

Item No. 157 :- Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications having various spans in between trusses and in multiples of standard length of bays as specified as per standard specifications, inclusive of cost of steel tubular trusses, tubular columns, purlins, tie runners, foundation bolts, base plates, nuts and bolts, welding wherever required, etc. as per detailed drawing inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade, etc. complete.

Item No. 158 :- Providing & fixing of colour coated zincalume (R) AZ 150 (Min 150 Gms/Sqm total on each sides) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 millimetre base metal thickness (BMT) (0.5 millimetre TCT), Hi-strength steel with minium 500 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium, 43.4% zinc, 1.6% silicon) with COLORBOND (R) steel quality super durable polyster paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nominal 950-1050 millimetre effective cover width and nominal 25-30 millimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 millimetre centre to centre. The end rib shall be designed for anti capilary groove and return leg. The feed material should have coil manufacturer's product details marked at regular interval. Including fasteners with minium fatened with minium 25 um zinc-tin alloy coated, hex head, self-drilling screw, etc. complete. (Weight of profile 4.52 Kg/Sqm). (For 2nd Floor).

Item No. 159 :- Providing and fixing 45 centimeter wide steel ladder of 40 x 6 milimeter mild steel flat stringers and steps of 18 milimeter diameter mild steel bar including fixing it in M-15 cement concrete block 60 x 30 x 30 centimeter and painting the ladder with antirust primer and two coats of oil painting including all leads and lifts etc. complete.

Item No. 160 :- Providing and fixing H.D.P. container Syntex or alike one piece moulded water tank made out of low density polythyler and built corrugation including of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow of all tanks capacity above 200 to 1,000 litres.

Item No. 161 :- Providing and laying in walls / ceilings / floors 50 millimetre diameter heavy grade having embossed as ISI Mark galvanised iron pipes of 6.33 kilogram / metre necessary fitting remaking good the demolished portion with filling trenches and with primer of anti-corrosive oil paint, 2 coats complete. Including necessary scaffolding and removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No. 162 :- Providing and fixing screw down for 50 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Item No. 163 :- Providing & fixing Exit singages at various location made up of Alluminium Compressed Material 3" thick including all material and labour complete.

Item No. 164 :- Excavation for foundation in earth, soils of all types, sand gravel and soft murum including removing the excavated materials upto a distance of 50 meters beyond the building area including all leads and lifts upto 1.5 metre, stacking and spreading as directed including dewatering, unless provided elsewhere preparing the bed for the foundation and necessary backfilling, ramming, watering including shoring and strutting etc. complete.

Item No. 165 :- Providing dry trap rubble stone soling 15 centimeter to 20 centimeter thick including hand packing and compacting etc. complete.

Item No. 166 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap metal for foundation and bedding including bailing out water, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc). ( For Ground Floor )

Item No. 167 :- Providing laterite stone masonary in cement mortar 1:6 in foundation and plinth including striking joints on the unexposed faces and watering complete.

Item No. 168 :- Filling in plinth and floors with contractor's murum in 15 to 20 centimeter layers including all leads and lifts watering and compaction as directed by Engineer-in-charge with all leads and lifts etc. complete.

Item No. 169 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints where plastering is to be done watering , scaffolding with all leads and lifts etc. complete. (Laterite stone 6 sides cut and thickness of morter joints shall be 12 millimeter miximum) ( Ground Floor )

Item No. 170 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 171 :- Providing sills of polished kadappa stone 25 millimeter to 30 millimeter thick, on a bed of cement mortar 1:4 including cement float, filling joints with neat cement slurry, curing, polishing, rounding edges, cleaning complete.

Item No. 172 :- Providing and laying telephone black / Amba White / Cadburybrown / Ruby red / Ocean Brown granite stone of 18 to 20 mm thick for door frame/ dado/ window boxing etc. on cement mortar 1:6 including filling joints with polymer base filler nosing the sharp edges wherever necessary, curing etc. complete.

Item No. 173 :- Providing and Fixing 30 mm. thick BOTH SIDE PRELAMINATED SOLID PANEL PVC DOOR SHUTTER consisting of frame made out of M.S tubes of 19 guage thickness and, size 19 x 19 mm for styles and 15 x15 mm for the top and bottom rails, M.S frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC 'C' channel made from 5 mm (+/0.25) thick prelaminated sheet of density 600 Kilogram/cbm ,of size 30mm thickness 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45? angle on either side forming stiles ; and 5 mm thick ,95 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered in 45 on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be falt and 20 mm shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/0.25) thick PVC sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm (+/0.25) x 30 mm PVC sheet beading on either side and joined together with solvent cement adhesive etc ,10 mm thickness (5 mm (+/0.25) x 2 nos ) 20 mm wide cross PVC sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S.powder coated but hinges of size 100 mm x 25MM x 2mm using 32 mm long steel screws drilled suitable to pass through both the walls of the M.S tube. Other hardwares

Item No. 174 :- Providing and fixing in position (as per 1868 / 1982) Alluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 millimetre at weight 0.637 kg/Rmt. with window frame bottom track section 92 x 31.75 x 1.30 millimetre at weight 1.070 kg/Rmt. Top and side track section 92 x 31.75 x 1.30 millimetre at weight 0.933 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. and handle and top section 40 x 18 x 1.25 millimetre at weight o.417 kg/Rmt. As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 millimetre thick High performance Single Glaze Unit (SGU) - Glass , and aluminium mosquito net shutter with stainless steel jail with all required screws and nuts etc, complete. With colour anodising without box.

Item No. 175 :- Providing and fixing in position powder coated aluminium louvered windows / ventilator of various sizes with powder coating as per detailed drawing and specifications including aluminium frames 80 x 38 millimetre x 1.22 millimetre box type, 5 millimetre thick sheet glass louvers, of approved quality etc. complete.

Item No. 176 :- Providing and fixing mild steel grill work for windows, ventilators etc. 15 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No. 177 :- Providing internal cement plaster 12 millimeter thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Item No. 178 :- Providing internal cement plaster 20 milimeter thick in two coats in cement mortar 1:4 without neeru finish to concrete, brick surface in all positions including scaffolding and curing with all leads and lifts etc. complete.

Item No. 179 :- Providing and laying Antiskid Ceramic tiles of approved quality of size 30 centimetre x 30 centimetre and confirming to IS 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.

Item No. 180 :- Providing and laying polished hand cut Kotah Stone flooring 25 millimeter to 30 millimeter thick and 45 centimeter to 55 centimeter wide in plain/diamond pattern on a bed of 1:6 C.M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning complete.

Item No. 181 :- Providing and laying ceramic tiles of having size 30 centimeter x 30 centimeter and confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.

Item No. 182 :- Providing and fixing white glazed earthenware Wash Hand Basin of 45 cm. x 30 cm. size including cold water pillar tap/cold and hot water pillar tap brackets, rubber plugs and brass chain, stop tap and necessary pipe connection including P.V.C. waste pipe and trap up to the outside face of the wall. Making good the damaged surface, testing etc. complete.

Item No. 183 :- Providing and fixing European type Colour glazed earthenware water closet pan with UPVC seat and lid with chromium plated brass hinges and rubber buffers including UPVC and vent pipe up to the outside face of wall without flushing cistern with flush cock and with water Jet and necessary fittings including cutting and making good to the walls and floors testing etc. complete.

Item No. 184 :- Providing and fixing white glazed earthenware lipped flat back/corner type Urinal with PVC 5 liters flushing cistern with fittings, inlet pipe with stop tap, brackets for fixing the cistern, 32 millimeter diameter P.V.C. flush pipe with fitting including lead soil pipe, lead trap and soil pipe connection up to the outside face of wall..

Item No. 185 :- Providing and fixing on walls/ ceiling/ floor 15 millimetre diameter Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No. 186 :- Providing and fixing on walls/ ceiling/ floor 25 millimetre diameter Chlorinated Poly Vinyl Chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Item No. 187 :- Providing and fixing 10 centimeter Poly Vinyl Chloride nahani trap with grating etc. complete.

Item No. 188 :- Providing and fixing 15 millimeter diametre screw down bib /stop tap of brass of approved quality and make, including necessary sockets, union, nuts, testing etc. complete.

Item No. 189 :- Providing and fixing screw down for 25 millimetre diametre wheeled stop tap of brass including necessary sockets/union nut complete.

Item No. 190 :- Providing and constructing Brick Masonry Inspection Chamber 60 centimeter x 45 centimeter x 90 centimeter including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C. I. cover of 75 kg with lid and frame fixed in cement concrete.

Item No. 191 :- Providing and fixing 100 millimeter diameter stabiliser pipe/ Poly Vinyl Chloride soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. complete.

Item No. 192 :- Providing structural steel work in hollow section of various thickness and sizes in square, rectanular and round shape from 25mm to 450mm section as per IS 4923 YST 310 Grade produced from iron ore and blast furnace route etc. as per detailed designs and drawing or as directed including cutting, fabricating, hoisting, erecting, fixing in position, making riveted/bolted/ welded connections and painting complete.

Item No. 193 :- Providing & fixing of colour coated zincalume (R) AZ 150 (Min 150 Gms/Sqm total on each sides) profiled sheets for roofing. The feed material is manufactured out of nominal 0.45 millimetre base metal thickness (BMT) (0.5 millimetre TCT), Hi-strength steel with minium 500 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% aluminium, 43.4% zinc, 1.6% silicon) with COLORBOND (R) steel quality super durable polyster paint coat (with inorganic pigment). The paint shall have a total coating thickness of nominal 35 um, comprising of nominal 25 um exterior coat on top surface and nominal 10 um reverse coat on back surface. Profile sheet shall have nominal 950-1050 millimetre effective cover width and nominal 25-30 millimetre deep ribs with subtle square fluting in the five pan at nominal 180-250 millimetre centre to centre. The end rib shall be designed for anti capilary groove and return leg. The feed material should have coil manufacturer's product details marked at regular interval. Including fasteners with minium fatened with minium 25 um zinc-tin alloy coated, hex head, self-drilling screw, etc. complete. (Weight of profile 4.52 Kg/Sqm). (For 2nd Floor).

Item No. 194 :- Providing and applying plastic emulsion paint of approved quality, colour and shade to old and new surfaces in two coats including scaffolding, preparing the surface. (excluding the primer coat) etc. complete.

Item No. 195 :- Providing and applying two coats of exterior acraylic emulsion paint confirming to corresponding I.S. of approved manufacture and of approved colour to the plastered surfaces including cleaning ,preparing the plaster surface, applying primer coat ,scaffolding if necessary , and watering the surface for two days etc complete.

Item No. 196 :- Providing and fixing hume pipe septic tank 900 millimeter diameter with vent pipe and cap including necessary fittings (including excavation and laying) etc. complete.

Item No. 197 :- Providing soak pit of size 120 centimeter x 120 centimeter x 120 centimeter including excavating and filling with brick-bats etc. complete.

Item No. 199 :- Excavation for foundation in Hard rock by chiselling, wedging, line drilling, etc. including trimming and levelling the bed, removing the excavated material upto a distance of 50 metres beyond the building area stacking as directed, dewatering and back filling with available earth/ murum watering, ramming etc. complete. (Lift upto 1.5 metre).

Item No. 200 :- Excavation for foundation in Hard rock by blasting including trimming and leveling the bed by chiseling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres from the building area including dewatering and back filling with available earth/murum, watering, ramming, etc. complete. (Lift upto 1.5 metre).

Item No. 201 :- Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/quartzite/gneiss metal for bed blocks, foundation blocks and such other items including bailing out water, plywood/steel formwork, laying/ pumping, compacting, roughening them if special finish is to be provided, finishing uneven and honeycombed surface and curing etc. complete. The Cement Mortar 1:3 plaster is considered for rendering uneven and honeycombed surface only. Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc. (Wooden centering will not be allowed.), with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 202 :- Providing laterite stone masonary in cement mortar 1:6 in foundation and plinth including striking joints on the unexposed faces and watering complete.

Item No. 203 :- Providing and constructing laterite stone masonry in cement mortar 1:6 in superstructure including raking out joints where plastering is to be done watering , scaffolding with all leads and lifts etc. complete. (Laterite stone 6 sides cut and thickness of morter joints shall be 12 millimeter miximum) ( Ground Floor )

Item No. 204 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 205 :- Providing and laying Cast in situ/Ready Mix cement concrete M-25 of trap metal for R.C.C. slabs and landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 206 :- Providing and fixing M-40 grade thick vibrated pull cast or similar type concrete frame with chamfer conforming to I.S. 65241983 having 6 mm dia. bars 3 Nos. And stirrups @250 mm c/c and fixing in wall with 6 Nos of hold fast of 12 mm dia bars 500 mm long including primer and oil painting etc, complete) frame size 60 mm x 100 mm.

Item No. 207 :- Providing and fixing 30mm thick SOLID PANEL PVC INTERNAL DOOR SHUTTER consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 40mm x 20mm for stiles ,top, lock and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5mm thick heat molded PVC channel of size 30 x 100mm forming stiles, and 5mm thick, 125mm wide PVC sheets for top rail, lock rail and bottom rail on either side, and 15mm (5mm x 3) thick, 20mm wide cross PVC sheet as gap insert for top rail and bottom rail. Paneling of 10 mm thick prelam PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles and rails with 30mm wide x 5mm thick PVC sheet beading on either side, and joined together with solvent cement adhesive etc. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the C Channel using PVC solvent cement adhesive. including stainless steel fixtures and fastening Complete as per direction of Engineer incharge, manufacturer's specification and drawing. ( For W.C. and bathroom shutters)

Item No. 208 :- Providing and laying machine cut machine Polished Kota stone flooring 25 mm. to 30 mm. thick and required width in plain/ diamond pattern on bed of 1:6 C. M. including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

Item No. 209 :- Providing and fixing in position. (as per I.S.1868 / 1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass with all required screws and nuts etc, complete. With colour Anodising without box

Item No. 210 :- Providing and fixing mild steel grill work for windows, ventilators etc. 15 kilogram per square metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.

Item No. 211 :- Providing and laying Cast in situ/Ready Mix cement concrete M-20 of trap metal for R.C.C. chajja as per detailed design and drawings including centering, formwork, cover blocks, laying/pumping, compacting and roughening the surface if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With natural sand/V.S.I. quality Artificial Sand

Item No. 212 :- Providing and fixing in position TMT (Thermo Mechanically Treated) FE-500 bar reinforcement of various diameters for R.C.C. pile caps, footings, foundations, slabs, beams columns, canopies, staircase, newels, chajjas, lintels pardis, copings, fins, arches etc. as per detailed designs, drawings and schedules. including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Item No. 213 :- Providing internal cement plaster 12 millimeter thick in single coat in cement mortar 1:4 without neeru finish to concrete or brick surfaces, in all positions including scaffolding and curing etc. complete.

Item No. 214 :- Providing sand faced plaster externally in cement mortar using approved screened sand, in all positions including base coat of 15 millimetre thick in cement mortar 1:4 using waterproofing compound at 1 kilogram per cement bag curing the same for not less than 2 days and keeping the surface of the base coat rough to receive the sand faced treatment 6 to 8 millimetre thick in cement mortar 1:4 finishing the surface by taking out grains and curing for fourteen days scaffolding etc.complete.

Item No. 215 :- Providing water proof bedding for flooring of Bath and W.C. 25 millimeter thick in C.M. 1:3 including using approved water proofing compound in specified proportion as per manufacturers specifications for per bag of cement including leveling, curing and covering 10 years guarantee on court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Item No. 216 :- Providing waterproof plaster in W.C. and bath 20 mm. thick for dado in cement mortar 1:3 with neat finishing, floating using waterproofing compound at the rate of 1 Kilogram. per bag of cement of approved make and manufacturer and curing (and filling joints of Nahani trap and any outlet by properly) etc. complete.

Item No. 217 :- Providing and fixing 80 mm. diameter water meter with non-return valve including strainer, sockets/ union nut and including water meter box making locking arrangement and lock.[Without chamber].

Item No. 218 :- Providing and fixing 45 centimeter wide steel ladder of 40 x 6 milimeter mild steel flat stringers and steps of 18 milimeter diameter mild steel bar including fixing it in M-15 cement concrete block 60 x 30 x 30 centimeter and painting the ladder with antirust primer and two coats of oil painting including all leads and lifts etc. complete.

Item No. 219 :- Providing and making ISI Mark ferrule connection of 50 mm. dia. to water main including ferrule coupling cast iron bell mouth cover, built in non return valve and fixing including excavation and reinstatement complete.

Item No. 220 :- Providing and fixing reinforced cement concrete cover of size 90 cm. x 45 cm. with frame over inspection chamber etc. complete. Medium duty (140 Kilogram).

Item No. 221 :- Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface, watering for two days etc. complete.

Item No. 222 :- Providing and applying washable oil bound distemper in two coats of approved colour, shade and quality to old/new surface including scaffolding, preparing the surfaces (excluding the primer coat) with all leads and lifts etc. complete.

Supplying and erecting PVC trunking (PVC casing-n-capping)of size 25 mm with accessories on wall/ceiling as perspecification No: WG-MA/CON.

Supplying and erecting mains with 2x1.5 sq.mm FRLSHcopper PVC insulated wire laid in providedconduit/trunking/inside pole/Bus bars or any other places per specification No: WG-MA/BW

Supplying and erecting mains with 2x2.5 sq.mm FRLSHcopper PVC insulated wire laid in providedconduit/trunking/inside pole/Bus bars or any other places. As per specification No: WG-MA/BW

Supplying and erecting mains with 2x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/insidepole/Bus bars or any other places. as per specification No: WGMA/ BW

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiringconnections complete.

Supplying and erecting modular type 3 pin 6A multi socketwith safety shutter, duly erected on provided plate and box with wiring connections complete

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected.

Supplying and erecting PVC Surface modular switch box withdouble mounting plate for 6 module duly erected.

Supplying and erecting 16 to 32 A, 10kA, DPMCB suitable to fix in 2 module of modular switch in provided box complete & duly concealed with necessary material and connected.

Point wiring for light/bell/exhaust fan in PVC trunking (casingcapping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Supplying and erecting LED square / circular Max. 25 W down lighter/ Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2750 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with 3 years warranty.

Making suitable size recess in any type of false ceiling for erection of flush type down lighter and finishing the background to match the original surface upto 20W.

Supplying and erecting bulk head LED fitting max. 10W withhigh transitivity diffuser with system lumens output of min.1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCTupto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95,operating range of 140-260V, in built surge protection of 2.5kV, Life class of 50,000 Hrs. at L70B50, including driver,IP66, IK09 rated on provided PVC Block / wooden board with3 years warranty.

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty.

Supplying & erecting UV Fly killer/ bug catcher Light Fitting having 2 x 20W UV Tube Lights to cover min. area of 500 sq.ft with powdered coated M.S./ steel body suitable to work on 230V, AC Supply having top mounting arrangement with SS chain complete and 3 core 1 mtr. flexible wire with 1 year warranty.

Supplying and erecting ding dong / electronic musical type call bell with heavy duty coil suitable to operate on 230V A.C. supply erected on polished double wooden block/sunmica block of suitable size.

Supplying and erecting exhaust fan medium duty 230 V A.C.50 cycles 225 mm. 1400 RPM with condenser completeerected in position with necessary materials. Fan motor withmoisture proof treatment and ‘E’ class insulation.

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying and erecting fan hook of 10 mm. M.S. round bar grouted in RCC slab with making the site as original.

Supplying and erecting ‘B’ class G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire.

water cooler 230/250V 50Hz nominal cooling capacity of 80 litres per hour and storage capacity 120 litres with partially stainless steel body as per specification no. AP-WCR/WC

Supplying and erecting ultra violet storage type water purifier (RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water minimum 0.33 litre/min with activated carbon filter and softener operating on 230V, single phase A.C. supply with UV fail & filter change indication system .(for TDS more than 200)

Supplying & erecting four pole ON LOAD change overswitch, 415V, 200A, open execution having staggeredtermination, phase barrier, shroud termination and terminalcover along with auxiliary contacts and ready to upgrade withfuse protection kit, operational current category AC23Acomplying to IS/IEC 60947-3 Part-1/3.(Note 1) Item no 5-1-1 to 5-1-8 are of open execution type tobe used in cubical panels. For using the item with enclosure,rates shall be increased by 35 % = Rs. 10548 + 3691.80 =14239.80)

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking DPMCB 40A to 63A, C-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting CRCA sheet metal one way enclosuresof 1.2mm thickness suitable for DP MCB /TP MCB/FPMCB/RCCB/RCBO complete erected on angle iron/GI frame.

Providing & erecting 4 Pole MCCB, 415 V, 100A, rated shortcircuit breaking capacity 25 kA (Ics=100% of Icu), adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact. MCCB with phase barriers on both sides, insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SWSWR/ MCCB ( As per Note for 4PMCCB add 20% = Rs.5309+ 1061.80 = Rs.6370.80)

Providing & erecting 4Pole MCCB 415V, 250A, rated shortcircuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per specification no. SWSWR/ MCCB ( As per Note for 4PMCCB add 20% = Rs.14159+2831.8 = Rs.16990.80)

Providing & erecting floor/wall mounting, MCCB panel board, with door, suitable for four pole incoming 250A, 8 ways Four pole outgoing, up to 100 A MCCBs on iron frame, as per specification no SW-SWR/MCCBPB. (Excluding MCCBs)

Providing & erecting incoming and outgoing cable alleyssuitable for MCCB panel board with door, 250A incoming and8 way outgoing or 400A incoming and 6 way outgoing madefrom CRCA sheet 1.6 mm thick duly powder coated andhaving vertical insulated partition for shielding between theshared face of cableway and DB.

Supplying and erecting terminal spreaders suitable for 4 pole, up to 100A MCCB (Set of 8)

Supplying and erecting terminal spreaders suitable for 4 pole, above 100A up to 250A MCCB (Set of 8)

Supplying and erecting SS enclosure for MCCB suitable for up to 100A MCCB.

Supplying and erecting SS enclosure for MCCB suitable for above 250 A up to 800A MCCB.

Supplying and erecting bus bar chamber triple pole with neutral with four copper bars, 500V, 100A having 10mm (Width) X 1.6 mm (Thickness), with 99.9 % Copper purity as per E91E Grade & Current Density 1.6 A per sq. mm. compliance to IS 5082 and Enclosure fabricated with 16 SWG CRCA sheet and epoxy paint, with suitable number of ways and with SMC/DMC Insulators and accessories of suitable rating complete as per specification no. CP-BB

Supplying & erecting LED type indicating pilot lamp with LED colours red / yellow / green, 230 / 250V on provided box / panel with necessary material, wiring & connections etc.

Supplying & erecting LED type indicating pilot lamp with LED colour blue, 230 / 250 V on provided box / panel with necessary material, wiring & connections etc.

Supplying, erecting & terminating FR XLPE insulated,galvanised steel formed wire armoured (strip) cable 1100 V, 2core 4 sq mm copper conductor complete erected with glands& lugs, on wall/ trusses/pole or laid in provided trench/ pipe asper specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 6 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting copper strip of high purity requiredsize used for earthing on wall and/or any other purpose withnecessary copper clamps fixed on wall painted withbituminous paint with joints required. As per specification no.EA-EP. (size of cu-strip 25x3mm = 0.67kg/mtr = 4nos x 5mtr+ 2nos x 20m = 20m+40m = 40m x 0.67kg/mtr = 40kg)

Supplying & erecting conventional spike type air termination suitable to carry lightning stroke made up of heavy gauge 40 mm dia copper pipe of standard length with 5 Nos. copper spikes fixed on copper ball as air terminals duly threaded in copper pipe er

Supplying and erecting mains with 1x1.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 1x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WGMA/ BW

Providing MSEDCL meter connection charges.

Supplying and erecting bus bar chamber triple pole withneutral with four copper bars, 500V 200A having 20mm(Width) X 2 mm (Thickness), with 99.9 % Copper purity asper E91E Grade & Current Density 1.6 A per sq. mm.compliance to IS 5082 and Enclosure fabricated with 16 SWGCRCA sheet and epoxy paint, with suitable number of waysand with SMC/DMC Insulators and accessories of suitablerating complete as per specification no. CP-BB

Supplying 16 amp. 3 pin plug Top bakelite type of 230 V. A.C. supply.

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 5.00 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. APAC/ WAC

Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor. room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 5.0 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position in provided recess with wooden frame complete specification no. AP-AC/WAC

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete.

Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete.

Supplying and erecting PVC insulated PVC round sheathed 2.5 sq.mm (50 no. x 0.25 mm dia.) 3/4 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any otherpurpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.(size of equal angle : 50x50x6mm = 4.5kg/mtr = 1.mx2nos =2.mx4.5kg/mtr= 9kg for each AC ODU x 11nos = 99kg)

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC /copper pipes having 9 mm thickness and inner diameter / sizes12 mm for solar water heater/AC system.

Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC system.

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original. 2) Rate for Item no 3-11-77 is for one quantity only. as per Note : For more than 1 qty upto 10 quantities reduce overall rate by 10% = Rs. 7519 - 751.90 = Rs.6767.10)

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking /inside pole/Bus bars or any other places. As per specification No: WG-MA/BW

Supplying and erecting mains with 4x6 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WGMA/ BW ( Note : for 4x6sqmm , double rate of 2x6sqmm = Rs.132 x 2 = 264 per mtr)

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type switch one way 16 / 20 A, duly erected on provided plate and box with wiring connections complete with neon indicator

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 module duly erected.

Point wiring for light/bell/exhaust fan in PVC trunking (casingcapping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per specification No: WG-PW/SW

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as perspecification No: WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular accessories as per specification No: WG-PW/CW

Supplying and erecting bulk head LED fitting max. 10W with high transitivity diffuser with system lumens output of min. 1100 lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., THD<10%, p.f. >0.95, operating range of 140-260V, in built surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50, including driver, IP66, IK09 rated on provided PVC Block / wooden board with 3 years warranty

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50,

Supplying and erecting exhaust fan medium duty 230 V A.C. 50 cycles 225 mm. 1400 RPM with condenser complete erected in position with necessary materials. Fan motor with moisture proof treatment and ‘E’ class insulation.

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF

Supplying & erecting 22 SWG G.I sheet metal cawl sector shaped with 25 x 25 x 3 (mm) angle iron frame, metal mesh to avoid birds entry with necessary material, suitable for exhaust fan of 300 mm as per specification no FG-FAS/MSC

Supplying, erecting & marking SPMCB 6A to 32A, C-serieswith rated short - circuit breaking capacity (Icn) 10kA inprovided distribution board as per specification no. SWSWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying, erecting & marking DPMCB 6 A to 32 A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 2 ways (2 poles) for outgoing SP MCBs, with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

Supplying, fixing and commissioning 2 pole RCBO 32/40A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO 63A, with overcurrent, rated short-circuit breaking capacity (10 kA) and earth leakage protection, with 30/100/300 mA sensitivity and short circuit and earth leakage trip indication as per specification no SW-RCCB/RCBO

Supplying, erecting & terminating FR XLPE insulated,galvanised steel formed wire armoured (strip) cable 1100 V, 2core 2.5 sq. mm. copper conductor complete erected withglands & lugs, on wall/ trusses/ pole or laid in provided trench/pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 2 core 4 sq mm copper conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 10 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete. (cu-bare wire 8swg = 0.1155kg/mtr = for each lift = 45m x 0.1155kg/mtr = 5kg x 3lifts = 15kg)

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

SITC of Electric Traction Passenger Lift with Rated capacity :- 10 Passenger/680Kg Floors :- G+4 floor (5 Stops/ 5 Landings) Travel :- 14.2 mtrs (approx.) Location of Lift Machine:- MR/MRL Rated speed :- 1.0 mps VS Car/Landing door clear opening of 800 mm wide x 2000mm high Clear Car size of 1300mm wide x 1350mm deep x 2250mm high Lift shaft available having clear size of 1900mm wide x 2100/2320mm deep, 1500mm Pit depth, 3000mm Overhead. Doors type :- COPO/TOPO Doors with frame made from SS 304 grade solid (non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames. The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. COP with SS face plate having metallic push buttons with Braille code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / ithout attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor. LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port. The controller shall have necessary protections such as overcurrent, overvoltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc.

SITC of Duplex Lift control system for two nos. microprocessor/PLC based simplex lift controllers along with necessary software with programming and hardware e.g. logic board, necessary communication/control/data cabling laying in rigid PVC conduits/trunking etc. complete. (for 2lifts adjucenet to each other)

Supplying and erecting GI sheet 1.25 mm (18 SWG) having zinc coating of 350 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. ( 3m (w) x 5m(L) = 15sq.mtr)

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. ( Cchannel 75x40x4.4mm = 6.8kg/mtr : 2.8m x 4nos = 11.2m x 6.8kg/mtr = 76.16kg, Equal Angle size 50x50x4mm = 3kg/mtr = {3mx2nos+5mx3nos+1mx6nos+0.5mx2nos= } 28m x 3kg = 84kg = Total 76.16kg + 84kg = 160kg + 5%wastage = Say 168Kg))

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 25 sq. mm. copper conductor complete erected with glands & lugs, on wall/ laid in provided trench/ pipe as per sp. No. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete

Providing earthing with copper earth plate size 30 x 30 x 0.315cm complete with all materials, testing & recording the resultsas per sp. No. EA-EP

Supplying and erecting copper strip of high purity required size used for earthing on wall with necessary copper clamps fixed on wall painted with bituminous paint with joints required. As per sp. No. EA-EP. (size of cu-strip 25x3mm = 0.67kg/mtr x 4m each x 4nos = 11kg)

Supplying, erecting, testing and commissioning of diesel generating set with alternator of 160 kVA output continuous rating, 3 Phase, 415 V, 50c/s 0.8 p. f. A.C supply, a totally enclosed air cooled / liquid cooled multi-cylinder diesel engine developing suitable BHP at 1500 rpm with 10% overload for 1 hour in 12 hours, along with standard accessories, self-excited, self-regulated, screen protected alternator with static excitation system running at 1500 RPM as per IS 4722-2001 with voltage regulation +/- 5 %, with performance class G2 and maximum fuel consumption 27.8 Ltr/hr @75% loading. Both the engine and alternator direct coupled on a common fabricated steel base frame and mounted on anti-vibrating pads with standard control panel comprising meters, switchgears, indicators connected with suitable wires/cables, the complete set enclosed in composite Acoustic enclosure as fully assembled integral unit made of 16 SWG CRCA Sheet, sound absorbing material to restrict sound level up to 75 dB at 1.0 m, provided with first filling of oil, diesel not less than 290 Ltr etc. on provided M20 Grade CC Foundation as per sp. No. GEN-DG

Supplying, erecting, testing and commissioning ofmicroprocessor based AMF panel suitable for dieselgenerating set of above 140 kVA up to 180 kVA capacityThree phase, 415 Volts, 50Hz A.C. with all standard features,safeties etc as per specification no. GEN-AMF. ( As per Notefor : In case of new DG set, if AMF/SYNC panel is to be usedin lieu of standard panel, reduce rate of Item No 11-2-1 to 11-2-23 by 10% of rate of new AMF panel/SYNC panel =Rs.165270 - 10% = 165270-16527 = Rs.148743).

Supplying, installing, testing and commissioning FR, XLPE armoured cable 4 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per sp. No. CB-LT/CU

Excavating hard Rock or bituminous road by chiselling for preparing pit for pole / stay/earth plate / for laying cable/ pipe & clearing the site by removing debris & making the site as required complete. (4.5m(L)x2.5m(W)x0.5m(D) = 5.6cu.mtr)

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose). ( size 2.5m (W)x4.5m(L)x1m(H)= 12.25cu.mtr = say 13cumtr)

Supplying and erecting 25 mm dia. corrugated flexible polypropylene conduit

Supplying and erecting mains with 4x4 sq.mm FRLSH copper PVC insulated wire laid in provided conduit as per sp. No: WG-MA/BW ( Note : For 3ph.pump instead of 2x4sqmm, needs to use 4x4sqmm cu-mains, hence double the rate of 2x4sqmm)

Point wiring for light/bell/exhaust fan in PVC casing-capping with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accesso. as per sp. No: WGPW/ SW

Wiring for plug on board with Switch socket surfacebtype, copper wiring and earthing and with modular accesso. as per sp. No: WG-PW/CW

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years

Supplying & erecting four pole ON LOAD change overswitch, 415V, 32A, open execution having staggeredtermination, phase barrier, shroud termination and terminalcover along with auxiliary contacts and ready to upgrade withfuse protection kit, rotary handle, operational current categoryAC23A complying to IS/IEC 60947-3 Part-1/3 . (Note 1) Itemno 5-1-1 to 5-1-8 are of open execution type to be used incubicalpanels. For using the item with enclosure, rates shall beincreased by 35 % = Rs.2948 + 1031.80 = 3979.80)

Supplying, erecting & marking FPMCB 6A to 32A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per sp. No. SW-SWR/MCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /FP MCB complete erected on angle iron/GI frame

Supplying and erecting marine (Waterproof) plywood 18/19 mm thick fixed to wall or on provided panel board with necessary materials such as screws, wall fasteners, supports, nut bolts etc. complete with compliance to IS 720:2010 ( size of plywood : 1m x 1m = 1sq.mtr)

Supplying and erecting iron work, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority. (size of equal angle : 40x40x3mm = 1.8kg/mtr = (1mx4nos + 0.3m x 4nos = 5.2mtr x 1.8kg/mtr = say 10kg)

Supplying, erecting & terminating FR XLPE insulated,galvanised steel formed wire armoured (strip) cable 1100 V, 4core 4 sq. mm. copper conductor complete erected with glands& lugs, on wall/ or laid in provided trench/ pipe as per sp.o.CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per sp. No. EA-EP

Supplying and erecting GI wire of high purity of required sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/ with screws complete

Supplying and erecting minimum Three & above star rated submersible pump set suitable for erection on open well of 3.75 KW/5 HP with 415 V 50 c/s. A.C. supply, having delivery head from 43 to 11m and discharge from 120 to 840 litres. per minute & pipe of Suction 65mm / Delivery 50 mm diameter erected with necessary H type clamps as per sp. No. WP-OSP

Supplying & erecting flat flexible 3 core 4 sq.mm PVC sheathed submersible type copper cable suitably clamped at fixed intervals with column pipe assembly complete.

Supplying & erecting automatic control panel for 3 Phase , 415volt, A.C, Submersible/centrifugal pump set up to 7.5 HPconsisting of DOL starter having relay range 9-14 AMP,S.P.P.,Combined ammeter/ voltmeter, phase indicating lamp enclosedin CRCA powder coated Vibration proof enclosure with IP 54protection. Control Panel should offer single phasing, phasereversal, phase imbalance etc .

Supplying and erecting 50 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per sp. No. FF-VL/BFV

Supplying and erecting ISI mark GI pipe 50 mm. dia ‘C- classposition with accessories complete. Sp. No. CW-PLB/GP

Supplying and erecting non return valve 50 mm dia in positionmade of gun metal complete

Supplying and erecting 40/50 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.8 mm conformingto IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement as per sp. No. ESD-HWP/CPVC

Supplying and erecting PVC casing-n-capping of size 25 mmwith accessories on wall/ceiling as per sp. No: WG-MA/CON.

Supplying and erecting mains with 2x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided casing .as per sp. No: WG-MA/BW

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided casing as per sp. No: WG-MA/BW

Supplying and erecting flush type shockproof plug socket 6A& 16A (6 pin) with 16A switch combined with indicator lamp and fuse with gang box on wooden board.

Supplying and erecting PVC insulated PVC round sheathed 1.5 sq.mm (30 no. x 0.25 mm dia.) 3 core flexible multi stranded copper Industrial cable for voltage grade up to 1.1 kV

Supplying and erecting integrated LED street light fitting 60W IP65 & IK08 class having single piece pressure die-cast aluminium housing, having system lumens output of Min. 6600Lumens, min. efficacy of 110 lumen/W, CRI>70, CCT upto6500K, THD<10%, p.f. >0.95, operating range of 140-270V,inbuilt surge protection of 10 kV, Life class of 50,000 Hrs. atL70B50, including driver complete with 3 Years warranty asper specification No FG-ODF/FLS2.

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SWSWR/ MCB

Supplying and erecting iron work, sheet metal work consistingof CRCA sheets, various sections of iron, plates, chequeredplates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding completeerected at the position with necessary materials duly paintedwith one coat of red oxide and two coats of enamel paint tomatch the switchgears or as per directions by the authority. ( Size of equal iron = 40x40x5mm = 3kg/mtr = 3mt x 3kg/mtr = 9kg)

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 4 core 4 sq. mm. copper conductor complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width& depth up to 90 cm) 50 mm outside dia. double wallcorrugated pipes (DWC) of HDPE for enclosing cable belowground/road surface, to required depth complete.

Providing & erecting 6 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OH-PL/PBKT

Providing pipe type earthing with 40mm. dia. G.I. pipe or 20 mm dia. G.I. Rod complete with all materials testing and recording the results as per specification no. EA-EP ( 6nos for Octagonal pole + 1no. For st.light control panle = 7nos)

Excavating hard murum / stone metal road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site as required complete. {1m(D)x0.3m(W)x0.3m(L) = 0.09cumtr x 2nos= 0.18cu.mtr say 0.2cu.mtr)

Making cement concrete foundation in 1:3:6 cement concrete, (20 to 25) mm. stone metal duly plastered with necessary curing for complete. (pole muffing or any other purpose). {1.1m(D)x0.3m(W)x0.3m(L) = 0.099cumtr x 2nos= 0.198cu.mtr say 0.2cu.mtr)

Making M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole).

Supplying and erecting HMS PVC conduit FRLS grade 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting modular type telephone socket one gang with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 1 module complete duly erected

Supplying & erecting 3 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/con

Supplying & erecting 20 pair telephone copper cable 0.5 mm dia. with high density polyethylene insulation, polyester taped, Nylon Rip Cord & grey colour sheathed with FR PVC, conforming to ITD specification S/WS 113C laid in provided PVC casing capping/co

Supplying & erecting 10 pair, 0.5mm dia, jelly filled unarmoured telephone copper cable with poly-al laminate moisture barrier, laid in provided PVC casing capping/conduit as per specification No. WG-TW

Supplying, erecting & commissioning MDF Box 50x50 pairs made from min. 1.5mm thick MS sheet as per specification no. WG-TW

Supplying, erecting & commissioning 20 pairs FR junction box with moulded plastic enclosure as per specification no. WG-TW

Supplying, erecting & commissioning 10 pair module for connection & disconnection of telephone cable as per specification no. WG-TW

Supplying and installing, testing & commissioning of digital(hybrid) type EPABX of 6 x 32 extensions suitable upto 96extensions complete. ( Note :- 1) Add Rs. 38159.00 foradditional 16 extension card for digital (hybrid) type EPABX= Rs. 60679 + 38159 = Rs.98838)

Supplying, installing, testing & commissioning push button telephone instrument desk top/wall mount with caller ID & Speaker unit as per specification complete

Supplying, installing, testing & commissioning IP telephone instrument as per specification complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 2 module duly erected.

Supplying and fixing tool-less IO (Ethernet) flush/surface type in provided modular box as per specification no. WG-NAS/IO

Supplying and installing cat-6 cable suitable for networking as per specification no. WG-COC/NC

Supplying and erecting LSZH armoured multimode optical fibre cable with 6 fibres, core dia 50/125 μm (OM3), suitable upto 10 GBPS, ethernet distance at 850 nm of wavelength, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-COC/O

Supplying and fixing 1 m UTP patch cord of Cat 6 type in position as per specification No. WG-COC/PC

Supplying and plugging 3 m fibre patch cord LC-SC MM (50) OM3 LSZH duplex complete as per specification no. WGCOC/ FPC

Supplying and installing single mode simplex pigtail with SC/LC splicing complete

Supplying, fixing, and configuring 20 Ports + 4 SFP combo, Layer 2, GB managed ethernet switch, with web view/CLI erected in provided rack complete

Supplying, fixing, and configuring 1-port mini-GBIC SX MMfibre transceiver (up to 550m, support 3.3V power) erected inprovided rack complete.

Supplying and erecting mains with 1x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided casing as per sp. No: WG-MA/BW

Supplying and erecting 40/50 mm (ID/OD) Chlorinated polyvinyl chloride pipe (CPVC), thickness 3.8 mm conforming to IS 15778 (CTS Series) with necessary CPVC fittings and solvent cement as per sp. No. ESD-HWP/CPVC

Supplying, fixing, and configuring broadband ADSL router with all accessories, on provided rack as per specification No. WG-NWC/ADSL

Supplying, installing and testing UTP connector (RJ-45) as per specification No. WG-NAS/UTPC.

Supplying and fixing 24 port patch panel with tool-less keystone jacks in provided U Rack complete as per specification no. WG-NAS/PP

Supplying and fixing 12 ports light guide unloaded interconnect unit, rack mounted type, with adapter panel for termination of optical fibre cables in provided U rack complete as per specification no. WG-NAS/ LIU

Supplying and fixing 9U wall mount rack (Dimension-DxWxH – 500x600x500 mm) as per specification No. WG-NAS/RAK

Supplying, erecting, testing and commissioning of 6kVA capacity online pure sine wave with backup time of ....... hrs. PWM & IGBT based UPS with 0.9 to unity output pf, single phase input & 1 phase output complete with all protections as per specification no. AP-UPS

Supplying and erecting 12V/100Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete.

Supplying and erecting iron work, sheet metal work consistingof CRCA sheets, various sections of iron, plates, chequeredplates, rods, bars, MS pipes, etc. for panel board or any otherpurpose with bending, cutting, drilling and welding completeerected at the position with necessary materials duly paintedwith one coat of red oxide and two coats of enamel paint tomatch the switchgears or as per directions by the authority.

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting annealed bare copper wire of high purity of required sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws complete.

Supplying and erecting G.I. pipe ‘C’ class ERW 150 mm dia with necessary fittings complete as per specification no. FF-PP (270 court yard + 42 wet riser)

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Providing coating of bitumen paint & 4mm thick wrapping for underground 150 mm ring main of fire fighting system.

Supplying and erecting stainless steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV

Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade /SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8" x 6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5)

Supplying and erecting 63mm dia, reinforced rubber lined (R.R.L.) hose pipe,15m in length, fitted with necessary accessories complete as per specification no. FF-FFA/RRL

Supplying and erecting stainless steel branch pipe 63 mm dia fitted with 20mm dia detachable hexagonal nozzle complete as per specifications no. FFFFA/ NZ

Supplying and erecting 150 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting M.S./CRCA cabinet for housing single hydrant valve of size ( 400 x 400 x 400)mm or hose pipe box of size ( 600 x 600 x 200)mm made from min. 1.5 mm thick CRCA sheet with angle iron work of min. of size (25 x 25 x 4) mm having front doors with viewing glass of size (200x150) mm and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour ( Code 538 of IS 5

Supplying and installing wall mounting swinging hose reel drum fitted with 19mm dia. 30m long high pressure polypropylene (Polyhose) along with necessary accessories complete as per sp. no. FF-FFA/HV

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 100 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS

Supplying and erecting 100 mm dia. pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per sp.no. FF-FFA/PG

Supplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of castiron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(d)Erected on

Supplying & erecting D.O.L Starter suitable for 415 V, 3 phase 50 cycles with no volt coil and overload element with necessary materials and connected to supply for 10 H.P.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 6 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ or laid in provided trench/ pipe as per sp. no. CB-LT/AL

Supplying, erecting & marking FPMCB 40A to 63A, with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB /TP MCB/FP MCB/RCCB/RCBO complete erected on angle iron/GI frame.

S u p p l y i n g & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg.capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S. flat with nut & bolts routed in wall complete.

Providing and fixing high-density polyethylene (HDPE) container one piece moulded triple layer water tank made out of high density polyethylene and builtcorrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet, outlet overflow pipe inclusive of all tanks capacity up to 20000 litres.

Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for pumps).

Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting ISI mark GI pipe 32 mm dia.‘B’ class at position with accessories complete as per specification no. CW-PLB/GP.

Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying, erecting, testing and commissioning of quartzoid bulb sprinkler, 15mm (½") dia. NBCM Body chrome finished, 68º C fixed temperature rating with deflector disc of conventional construction complete as per specification no. FFSPR.

Supplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD display with min 16 lines of text, operating at 230 V 50HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, suitable provision for network connectivity,interfacing with third party equipment via a MODBUS/ OPC/ L-ON interface etc. conforming to IS 15908:2021, IS 2189: 2008, EN 54 & VDS / FM/ UL 864(10th edition) with 3 years replacement warranty FF-AFAS/CP.

Supplying, installing, testing and commissioning of repeater panel with suitable battery backup of a minimum of 24 hours in normal condition and 30 min in alarm condition, 80 backlit alphanumeric LCD display with inbuilt buzzer to indicate fault/fire alarm, manual control keys for silence/mute and to reset the FACP from the repeater station. Panel size shall not more than 175 x 275 x 65mm conforming to EN 54 or UL approved with 3 years equipment replacement warranty FF-AFAS/RP

Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with "Break Glass" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 or UL listed with 3 years equipment replacement warranty FF-AFAS/MCP.

Supplying, installing, testing and commissioning of addressable horn cum strobe sound/ hooter, output frequency 500 to 1000 Hz with dB as per Chart given in IS 15908:2021, with flashing at 1 Hz over the strobe’s entire operating voltage range EN 54, conforming to IS 2189: 2008, IS 15908:2021 standards with 3 years equipment replacement warranty FF-AFAS/SSH.

Supplying, installing, testing and commissioning of addressable optical smoke detector, single/twin LED’s with 360 degree view, suitable for low voltage 15 to32 V DC two wires supply, in-built locking mechanism to check the removal and pilferage of the detector, in built isolation mode, start up current 300μA and alarmcondition current shall be maximum 6.5 mA, operating temperature 0°C to 50°C, humidity 0-95% RH, IP 41, conforming to IS 2189: 2008, 11360_1985_Reff2020EN 54 or UL Approved with 3 years equipment replacement warranty

Supplying, installing, testing and commissioning FR, XLPE armoured cable 2core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU

Supplying, installing, testing and commissioning of addressable fire control/relay module complete as required, with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 reed relays, EN 54 or UL Listed FF-AFAS/CRM

Supplying, installing, testing and commissioning of addressable fire isolator module complete as required. EN 54 /FM or UL Listed with 3 years equipment replacement warranty conforming to IS 5051Part 2 (Sec 1 to 3) : 1982 Reed relays FF-AFAS/ISM

Supplying and erecting G.I. pipe ‘C’ class ERW 200 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings complete as per specification no. FF-PP

Supplying and erecting 200 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 200 mm dia cast iron double flange ball type NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV

Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV

Supplying and erecting 200 mm dia cast iron foot valve ball type/flap type with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 200 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV

Supplying and erecting 300 mm dia 1.5m in height air vessel / tank fabricated from min 5mm thick M.S. sheet complete as per sp. no.FF-FFA/ACT

Supplying and erecting 100 mm dia. Press.gauge, 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I.pipe, elbow etc. complete as per sp. no. FF-FFA/PG

Supplying and erecting 12/15 mm dia pressure switch with provided isolation valve, G.I. nipple, elbow, etc complete as per sp. no. FF-FFA/PS

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 120 sq. mm.aluminium conductor complete erected with glands & lugs, on wall/ or laid in provided trench/ pipe as per sp. no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 50 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ or laid in provided trench/ pipe as per sp. no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3 core 25 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/or laid in provided trench/ pipe as per sp. no. CB-LT/AL

Supplying and installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessoriescomplete as per sp. no. FF-FFA/PT

Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC

Supplying and erecting G.I. pipe ‘C’ class ERW 25 mm dia with necess.fittings complete as per sp.no. FF-PP

Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV

Supplying and erecting 200 mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, screen of SS end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS 22086.75

Supplying, installation, testing and commissioning of main fire pump (MFP /EP) suitable for water discharge of 2280 to 2850 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 55kW or of suitable kW capacity for manual/automatic operation and consisting of following : (a) Horizontal type, single stage, centrifugal/split casing pump of cast iron body & bronze impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520.(b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per sp. no. FF-MFP/SSC/EP

Supplying, installation, testing and commissioning of jockey fire pump (JP)suitable for water discharge of 180 to 240 LPM at 90 to 70 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 9.3 kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal/vertical type, multi stage, centrifugal casing pump of cast iron body & bronze impeller with stainless steel shaft(SS410 grade), mechanical sealconforming to IS 1520. (b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitablefor operation with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) M.S. fabricated common base plate, coupling, coupling guard, foundation boltsetc. as required. (d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003)complete, as per sp.no. FF-MFP/JP

Supplying, installation, testing and commissioning of main fire pump (MFP/DP) suitable for water discharge of 2280 to 2850 LPM at 90 to 60 m head driven by 76 HP or suitable HP capacity diesel engine at requiredworking speed suitable for manual/automatic operation and consisting

Supplying, erecting, testing & commissioning of fire pump control panel (FCP) of cubical construction, floor mounted type, fabricated from minimum 2 mm thick CRCA sheet, compartmentalised with hinged lockable doors, with enclosure protection class IP54, duly powder coated or painted with accessories dulypainted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003), cable alley, interconnection withsuitable size solid copper busbar strip of adequate size for all power connections having switchgears and accessories, mountings and internal wiring with adequate size copper conductor cable, earth terminals, numbering etc. complete in all respect, suitable for satisfactory operation of main fire pump and jockey(pressurisation) pumps (1working+1standby) with necessary accessories, wiring &cabling along with allied accessories with following incoming and outgoings,suitable for automatic & manual operation on 415V, 3 phase, 50Hz ac supply as per specificationsthe capacity of electric motor driven pump are as follows a. Main fire pump(MFP) having capacity of 55kW 1no (1 working) b. Jockey pump(JP) capacity of suitable capacity 2 nos(1 working +1 standby,alternate run per start in auto mode)comprises of the following features & switchgears:1. Main incomer FP SFU having rotary handle with HRC

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP. ( size of strip = 25x3mm = 0.590 kg/mtr = for eath strip 6m x 4nos = 24mtr x 0.59kg/mtr = 14.16 kg = Say 14kg)

Point wiring for light/bell/exhaust fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per sp. No: WG-PW/SW

Point wiring for ceiling fan in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FRLSH grade copper wire, modular type switch, earthing and required accessories as per sp. No: WG-PW/SW

Wiring for plug on board with Switch socket surface/concealed type, copper wiring and earthing and with modular acces.as per sp.No: WGPW/CW

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 25mm with accessories on wall/ceiling as per sp. No: WG-MA/CON.

Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit/ trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW

Supplying, erecting & marking SPMCB 6A to 32A, C-series with rated short -circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short -circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking DPMCB 6 A to 32 A, B-series with rated short -circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB), with 2 ways for incoming and 6 ways (6 poles) for outgoing SP MCBs,with door, 1.2mm thickness surface / flush mounted, IP 43 Protection on iron / GI frame as per specification no. SW-SWR/MCBDB

Supplying and erecting flush type shockproof plug socket 6A & 16A (6 pin) with 16A switch combined with indicator lamp and fuse with gang box on wooden board

Supplying and erecting anodized aluminium corridor / passage light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<10%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs. at L70B50, including driver, with end caps on provided PVC Block / wooden board with 3 years warranty

Supplying and erecting energy saving ceiling fan 230 V A.C. 50 cycles 1200mm complete erected in position as per specification no. FG-FN/CF

Providing & erecting 4 Pole MCCB 415V, 250A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/UV/trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure/panel as per sp.no. SW-SWR/MCCB ( As per Note for 4Pmccb Add 20% = Rs.14159+2831.80 = 16990.80 )

Supplying and erecting terminal spreaders suitable for 4 pole, above 250A up to 400A MCCB (Set of 8)

Supplying and erecting SS enclosure for MCCB suitable for above 250 A up to 800A MCCB.

Supplying, erecting, testing and commissioning 120 W amplifier suitable to operate on 230 Volts A.C. / 12 Volts D.C. supply complete as per sp. no. FF-PA/AFR

Supplying, erecting, testing and commissioning 15 to 30 Watts sound column or ceiling mounted complete as per specification no. FF-PA/SOC

Supplying, erecting, testing and commissioning stand mounted/handheld type wired microphone having 2 mV/Pa sensitivity, impedance level limit 300 ohms and 50 - 16000 Hz suitable to operate in -10 deg C to +55 deg C with min. 7 metre shielded cable and 3 Pin Professional XLR Connector, stereo jack complete as per specification no. FF-PA/MIC

Supplying, erecting, testing and commissioning rust free microphone floor stand of chrome plating/powder coating or S.S. material , 500 mm to 1500 mm height and sturdy mechanism ensuring trouble free movement complete

Supplying, erecting, testing and commissioning of 2 core shielded cable complete as per sp. no. FF-PA/MCC

Providing & erecting 4 Pole MCCB 415V, 400A, rated short-circuit breaking capacity 36 kA (Ics=100% of Icu), adjustable thermal (overload) setting and adjustable magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, with insulation withstand capacity 800V, no line-load bias in provided enclosure /panel as per specification no. SW-SWR/MCCB (As per Note for 4P MCCB add. 20% Rs. 18563 + 3712.60 = Rs. 22275.60)

Supplying & erecting fuse bridges with base HC type fuse links 415V, 300A erected on polished wooden block.

Supplying & erecting porcelain/epoxy bus bar support complete erected in provided M.S. box for 400A

Supplying and erecting GI sheet 1.25 mm (18 SWG) having zinc coating of 350 microns with galvanization process compliance to IS 2629:1985 to be used for fabrication of boxes panel boards etc. including cutting, bending, drilling, welding, riveting etc. and painting with one coat of red lead paint and 2 coats of enamel paint. (1.2m x 1.2 m x 2 nos + 0.4m x 1.2mx4 nos = 2.88 + 1.92 = 5 sq.mtr)

Supplying and erecting GI sheet 1.6 mm (16 SWG) caution board of size 200 x 150 mm duly painted with red oxide and enamel paint in Marathi, Hindi and English erected at position for medium

Supplying and erecting of any size electrolyte aluminium patti or bar in bus bar chamber / in panel or any other purpose, 500 V with require capacity 99.9% aluminium purity with E91E Grade as per IS 5082 & Current Density 0.8 A per sq. mm. with fixing arrangement (like lug or bottle type lug) to both the end with high grade polyolefin insulation sleeve complete as per specification no. BCP-BB (Size of Al patti 50 x5 mm = 0.673/mtr = 1m x 4 nos + 0.4m x 12 nos = 8.8 mtr x 0.673 kg / mtr = 6 Kg)

Supplying and erecting LT CT multifunction DLMS compliance energy meter of accuracy of class 0.5 , 3x240V,50 Hz with optical & RS 232 port, backlit LCD, measure & display trivector energy, load survey, TOD, tamper detection & logging, power ON /OFF events, instantaneous parameters of rating 1/5 A with display in absence of power complete with zero adjustment & test certificate from manufacturer erected on provided M.S. box and connected to CTs.

Supplying and erecting LT current transformer with bar primary 50/5 to 1000/5 ratio with 15 VA burden erected in provided CRCA box duly secured with insulating materials connected to the meter with test certificates.

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 95 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating FR XLPE insulated, galvanised steel formed wire armoured (strip) cable 1100 V, 3½ core 185 sq. mm. aluminium conductor complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 75 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Supplying and erecting rolled steel joist (girder) pole 100 x 116 mm (23 kg/m) with base plate in provided foundation as per specification no. OH-PL/RSJ (DP str. 11m x 2nos=22mtr)

Supplying & erecting MS pole bracket for guarding/LT OH line, fabricated from angle iron 50x50x6mm and 550mm long for necessary nos. of provided insulators, and erecting on pole with 50x6mm clamp complete as per specification no. OH-PL/BKT

Supplying & erecting pole bracket for OH conductor fabricated from ISM channel, 75x40x6mm, 550mm long for necessary nos. of provided insulators and welded with extension channel pieces of same size 300 mm in length and erecting on pole with 50x6mm clamp complete as per specification no. OH-PL/BKT

Supplying & erecting 100 x 50 x 6 mm with 4.7 mm thick web and 7.5 mm thick flange channel iron cross arm of suitable length for 2.4 m wide DP structure and erecting on DP with 50x6mm clamp complete as per specification no. OH-PL/BKT

Supplying and erecting porcelain disc type insulator 45KN with necessary hardware suitable for 11kV line, complete as per specification no. OH-INS/DI

Supplying and erecting porcelain pin type insulator with GI pin suitable for 11kV line, complete as per specification no. OH-INS/PN

Supplying and erecting distribution class, 11 kV thyrite type lightening arrester with nut bolts, on provided MS channel as per specification no. OH-INS/LA

Supplying and erecting G.I. self stay set for pole, including anchor plate 300x300x6mm straining screw, loop-insulator, G.l. stay wire 7/10 SWG, G.l. stay rod 20mmx1.8m long, erected with pole clamps along with angle iron bracket of 50x50x6mm and one meter long fixed to pole at suitable height with suitable MS clamps duly erected in provided C.C. foundations complete.

Supplying and erecting pole clamp made from 50x6mm MS flat for pole or pipe, post erected with 15mm bolts and nuts duly painted with one coat of red oxide and two coats of aluminium paint complete.

Supplying and fixing MS round base plate 25cm dia and 10mm thick fixed to pole welded and fixed at position.

Providng earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting GI strip of high purity required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint with joints required. As per specification no EA-EP. (Size of GI strip 25 x 3 mm = 0.59 kg/mtr = Avg. 7 m x 8 nos = 56 mtr x 0.59kg/mtr = 33

Supplying, installing, testing & commissioning 3 phase, 11/0.433 kV, 50 Hz., 200 kVA, Mineral oil immersed and naturally cooled outdoor type, copper wound Non-sealed transformer delta/star connected with additional neutral brought out on load side, temperature rise should not exceed 45℃ by thermometer in oil and 50 ℃ by the resistance method in winding at full load rating, using type A winding insulation (kraft paper) with HV tapping (with off load tap changer)off load +2.5 to -5 in steps of 2.5%, having 4 number of tap positions, with standard accessories complete with test certificate with losses below 780 Watts at 50% load, 2300 Watts at 100% load as per IS:1180 (part 1) : 2014 , with necessary permissions of Electrical Inspector, as per specification no SS- TR-NSL.

Supplying and erecting 11 kV outdoor type gang operated air break, triple pole switch 400 A capacity with 3 post pin type insulator per phase, mounted in horizontal or vertical position with necessary channels on provided cross arm with adequate length of "C" class G.l. pipe for operating handle erected on extended square shaft. The operating handle provided with lock and key at suitable height from ground

Supplying and erecting, 11 kV outdoor type drop out fuse with insulator complete with fuse holders, fuse barrel with metal fitting, fuse element mounted on M.S. channel with working current of 15A capacity complete erected on provided cross arm.

Supplying and erecting 11 kV fuse barrel with metal fittings complete.

Supplying and erecting hard drawn copper solid wire no. 0 to 6 SWG complete erected for connections on H.T. sides. 4SWG cu.conductor = 0.243 kg / mtr = 9 mtr x 0.1668 kg = 2 kg

Supplying and erecting extra thick alkathene pipe 10 mm dia. erected to enclose bare conductor wires complete.. (use shall be restricted to H.T.)

Supplying and erecting fencing of section having size 2450 mm in height from ground level and 1200 mm width with angle iron frame work erected in CC foundation and painted complete as per specification no SS-AS/FSG (Total fencing (excluding door 3 m width) = 22.2 mtr / 1.2 mtr =18.50 nos)

Supplying and erecting 50 x 50 x 6 mm angle iron as corner support 2m long fixed at the middle of the fencing frame and the other side inclined at 30 degree angle, in cement concrete foundation of 15 x 15 x 40 cm complete duly painted with one coat of red oxide and two coats aluminium paint complete.

Supplying and erecting double leaf hinged door each 1500 mm in width x 1850 mm in height using B class, GI pipe with angle iron supports, chain link wire mesh (jali) complete supported on channel iron, erected in foundation, and painted complete as per specification no SS-AS/DLD

Supplying & erecting barbed wire two ply with 12 SWG ply and 12 SWG barb with a gap between two bars of 75 mm. firmly fixed on provided angle supports with necessary materials complete. (6.044 meters/kg. x 88.8 mtr = 15 kg).

Supplying and spreading stone metal 25 mm size for 100 mm depth above the ground level complete. (6.6 mtr x 6 mtr = 40 sq.mtr)

Making transformer plinth (1.5 x 1.5 x 1.5) m in size with necessary excavation in ground with 150 mm. thick M- 10 PCC at the bottom and top and 250 mm. thick, burnt brick wall constructed at periphery and remaining hollow portion shall be filled with 40mm hard broken aggregate. External surface duly plastered by 12 mm thick including watering etc complete.

Making cement concrete foundation including excavation (60 x 60) cm x deep 1/6 of pole length in 1:3:6 cement concrete 20 x 25 mm stone metal, 45 cm x 45 cm x 45 cm /45 cm dia. x 45 cm. height plinth duly plastered, with necessary curing and finishing complete. (for above 9 m poles)

Making cement concrete foundation including excavation (60 x 60 x 150) cm deep in 1:3:6 cement concrete, (20 to 25) mm stone metal with necessary curing and finishing complete.(for stay).

SHRI K S POWAR