REPAIR TO PLASTER, PAINTING AND ASSOCIATED WORKS AT ZONE B OF MIL STN BD BARI UNDER GE KALUCHAK

Amount

Taking down chowkats or frames with shutters (without taking off shutter from the frames) not exceeding 1.50 Sqm each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutter from the frames) exceeding 1.5 sqm & not exceeding 4 sqm each complete all as specified and directed

M&L for pressed steel frames of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed .

M&L for pressed steel frames of size 125mm x 60mm for doors with one or more rebates including necessary fixing lugs, keys , hinges lock, lock strike plate etc.made out of 1.25mm thick MS sheet including one shop coat of red oxide zinc chrome primer etc complete all as specified and directed .

M&L for PCC 1:3:6 type C - 1 (using 20 mm graded crushed stone aggregate) as in back filling of chowkats and bed blocks for hold fasts etc complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides with partical board complete all as specified and directed.

M&L for 2nd Class hard wood 35mm thick factory made glazed and skelton shutters open rebated and prepared to receive glass , gauze,etc (without sash bars) edges of framing plain , chamfered or rounded. Fitted with cut and mitred beads for securing wiremesh supplied and fitted to chowkats complete all as specified and directed.

M&L for mild steel framed work as in doors ( as in chowkats)or gates of angle or other section with guest plates rails, braces rail etc exculsive of steel sheeting or other covering hanging also fastening and fixing complete confirming to Fe-410- W(Gde- E-250) quality- B including shop coat of red oxide including preparation of surface before fixing.

M&L for Solid PVC door/cup board frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, suppling and fixing in opening complete all as specified and directed.

M&L for Factory made solid panel PVC door/cup board shutter 30mm thick (style) consisting of frame made out of M.S tubes for top & bottom rails. M.S frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement or stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, suippling and fixing in the frame at site as per specification in SSR Part-I. complete all as specified and directed.

M&L for Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with 2nd class soft wooden beadings or fixed with screws to Iron framed windows all as specified and directed.

M&L for Butt Hinges medium weight cold rolled mild steel of size 100 mm complete all as specified and directed.

M&L for 150 mm size mild aluminium handles cast type anodised complete all as specified and directed

M&L for 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for 150mm Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

M&L for300 mm size Mild steel stove enamelled helical door spring fixed to Pressed steel frame / chowkhats including necessary welding complete all as specified and directed.

M&L for Steel ventilator with top hung shutter including hinges , steel peg stay including taking down old steel ventilator of any size complete all as specified

Dismantling of plain or corrugated steel sheeting ,any gauge, thickness including roof covering etc complete all as spfd and directed

Dismantling of plain or corrugated asbestos cement sheeting ,any gauge, thickness including roof covering etc complete all as spfd and directed

M&L for Pre-painted galvalume aluminum zinc coating GI based profile steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed.

M&L for Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in as in ridges, hips, valley gutters, drip and straight flashings, fixed with self tapping screws, complete all as specified & directed.

S&F GI T Grid system in ceiling 600 x 600 mm module which includes providing and fixing wall angle along the perimeter of the room with nylon sleeves and wooden screws at 300 mm center to center. Suspending the main tee of size from the soffit, soffit cleat, rawl plugs and wire rod and levelling spring clip at 1200 mm center to center cross tee, interlocked into the pre-cuts in the main tees at 600 mm center to center in direction perpendicular to the main tee to make a grid of 600 x 1200 mm. 600mm cross tees are interlocked in the pre cut slots in the 1200 mm tees at 1200 mm center to center in direction parallel to the main tee. Cross tees having length more than 600 mm are to be supported independently. 4.5 mm thick E board with square edge of size 595 x 595 mm be placed in the grid of 600mm x 600 mm. Size of grid is specified by manufacturers

Demolition of brick work or stone masonary built in cement mortar including all quoins , arches, pillar etc but excluding ashlars facing dressed stone work and pre-cast concrete article complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 all as specified and directed

M&L for Brick work with sub class ‘B’ bricks ,straight or curved on plan exc 6 m mean radius and built in cement mortar 1:6 complete , but except bricks , i.e using serviceable bricks obtained from demolition complete all as specified and directed

Demolition of cement concrete (un-reinforced) of any description and in any position not otherwise specifically provided complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6, nominal mix, type C2, using 40mm graded crushed stone aggregate as in sub base of floor, hard standing, path, pavings, plinth protection etc, surface finished even and smooth without using extra cement, laid in alternate bays, complete all as specified & directed.

Supply only Integral water proofing compound liquid complete all as specified & directed.

M&L for capilary rise treatment of walls as following :- Base coat: Berger HS Latex plus (or equivalent) Consumption base coat: 0.3 kg/m2 Second and Third coat: Latex sheild 2K (or equivalent) Consumption top coat: 3 kg/m2 System requirements: density: 2.00 kg/ltr Compressive strength: 0.5 N/mm2 Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'AB' on page no. 82 of tender documents as per Sch 'A' Note No 19 Page No 17).

Taking down cement plaster on bricks or stone wall / ceiling decayed surfaces of concrete , roof projections or chajjas etc upto triple storey including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for Rendering 15mm thick fair faces of brick / concrete surfaces in cement mortar 1:4 finished even and smooth with out using extra cement complete all as specified and directed.

M&L for Rendering 10mm thick on fair face of brick / concrete surfaces in cement mortar 1:6 finished even and smoth without using extra cement complete all as specified and directed.

M&L for Rendering 5 mm thick on concrete surfaces of ceilings in cm 1:3 finished even and smooth without using extra cement complete all as specified and directed

Dismantling water tanks of any description 1000 Ltrs capacity any position complete all as specified and directed.

Dismantling water tanks of any description 500 Ltrs capacity any position complete all as specified and directed.

M&L for Rotational moulded polyethlene water storage tanks , triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 1000 litres including over flow , drain out pipe and all accessories complete all as specified.

M&L for Rotational moulded polyethlene water storage tanks , triple layered, (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of Capacity 500 litres including over flow , drain out pipe and all accessories complete all as specified.

Supply and fixing in repair 20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe minimum weight 210 gms complete all as specified and directed.Make Prayag.

Taking up or down 20 mm bore steel tubing and connections including cleaning, threading for prefixing or removal complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections including cleaning, threading for prefixing or removal complete all as specified and directed.

M&L for Steel tubing medium grade galvanised of 20mm bore with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L for Steel tubing medium grade galvanised of 15 mm bore with all fitting and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

M&L for refixing old galvanised steel tubing of 20 mm bore and connections in new or old position with all fittings fixed complete to walls , ceiling, or laid in floors etc complete all as specified and directed.

M&L for refixing old galvanised steel tubing of 15 mm bore and connections in new or old position with all fittings fixed complete to walls , ceiling, or laid in floors etc. complete all as specified and directed.

M&L for Stop cock 20 mm cast cooper alloy of screwed down high pressure with crutch or Fancy type , screwed with ends for iron pipe or unions fixed in repairs. Make ISI marked

M&L for stop cock/ angle valve 15 mm cast cooper alloy of screwed down high pressure with crutch or Fancy type , screwed with ends for iron pipe or unions fixed in repairs. Make ISI marked

M&L for bib taps 15mm dia cast copper alloy fancy type chromium plated, screwed down for iron pipe or for brass ferrule fixed in repair complete all as specified and directed.

M&L for pillar taps 15 mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure with or with out lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts screwed for iron pipe fixed in repairs complete all as spd & directed.

M&L for stop valve 15mm dia cast copper alloy chromium plated fancy type with long shank and cup (concealed type) srewed both ends for iron pipe or for union and fixed in repair all as spd & directed

M&L for Angle valve 15 mm fancy type, chromium plated 15 mm of cast copper alloy, screwed down for iron pipe ,fixed in repairs complete complete all as specified and directed.

S&F in repair wall mixer, 3 in 1 system including over head shower chromium plated fancy type, 15 mm bore complete all as specified and directed.

M&L for Fancy type Brass CP wash hand basin mixer for mixing hot & cold water, screwed down, high pressure screwed both ends for 15 mm bore iron pipe or for unions fixed in repairs complete, all as specified.

M&L for Shower rose of C.P. swival joint of size 125mm for fixing 15mm pipe including fixing to steel pipe or union fixed in repairs all as specified and directed.

M&L for PVC connections 15mm dia & 600mm long with PTMT nuts all as spd & directed

M&L for PVC connections 15mm dia & 450 mm long with PTMT nuts all as spd & directed

M&L for Sheet glass shelf assembly consisting of 5,5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long make Jaguar or equivalent complete all as specified & directed.

M&L for vitreous china wash down water closet (pedestal pattern) coloured complete, including connection to drain pipe and to flushing pipe antisyphonage pipe etc, including seat cover fixed in repair, complete all as specified & directed.

M&L for vitreous china squatting pan 'Orissa' pattern long pan size 580 x440 mm white with integral foot rests (excluding cistern and flush pipe), fixed in repair, all as spd & directed)

S& F in repair Low level flushing cistern PVC valveles syphonic action type flushing cistern white with inlet valve,float and handle including bracket etc complete all as specified & directed.

M&L for vitreous china wash basin white corner type of size 325x325 mm excluding taps waste chain and plug and porcelain stopper but including brackets, complete all as specified & directed.

M&L for vitreous china wash basin white flat back size 580x450 mm excluding taps waste chain and plug and porcelain stopper but including brackets, fixed in repair, complete all as specified & directed.

M&L for PVC 32mm dia waste pipe with CP coupling, complete all as specified & directed.

M&L for Tubular towel rail, brass chromium plated, 20 mm dia, D type, 60 cm long between Hangs, fixed in repairs complete all as specified & directed.

M&L for PVC (SWR) floor trap , plain with grating including jointing with solvent cement of 75mm outlet dia complete all as specified & directed.

Dismantling cast iron or reinforced concrete drain pipes of 75/100mm bore, fixed with walls and taking out of trenches, if required all as specified and directed.

S&F PVC (SWR) pipes single socketed,110mm bore in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified & directed.

S&F PVC (SWR) bends any radius 110mm bore complete all as specified & directed.

S&F PVC (SWR) branch piece, (single Y) equal or unequal 110mm bore complete all as specified & directed.

S&F PVC (SWR) junction single (single T) equal or unequal 110mm bore complete all as specified & directed.

S&F PVC (SWR) pipes single socketed,75mm bore in any length with rubber ring joints, laid in trenches or in floors complete all as specified & directed.

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber ring joints fixed to wall including fixing clamps complete all as specified.

S&F PVC (SWR) bends any radius 75mm bore all as specified complete all as specified & directed.

S&F PVC (SWR) branch piece, (single Y) equal or unequal 75mm bore complete all as specified & directed.

S&F PVC (SWR) junction single (single T) equal or unequal 75mm bore complete all as specified & directed.

S&F PVC(SWR) vent cowl 75 mm bore complete all as specified & directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs washers and wastes including bedding in cement mortar to dwarf wall or including fixing cantilever brickets and connecting union to pipe overall size 915mmx460mm bowl size 410mmx330mmx160mm complete all as specified & directed.

M&L for TMT steel bars 10mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, complete all as specified & directed.

M&L for TMT steel round bars 6 to 8mm dia and over, cut to length bent to shape required, including cranking, bending spirally for hooping to columns, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia, complete all as specified & directed.

M&L for Form work to soffit of suspended slab such as roof slab not exc 20 0 mm thick horizontal or slopinf flate including fair finished to concrete surfaces complete all as specified & directed.

M&L for RCC 1:2:4 type B1 (using 20mm graded aggregate as in suspended slabs or chajja complete all as specified and directed

M&L for Providing Precast cement concrete 1:2:4 Type B-1 (using 20 mm graded aggregate) in landings, cover slabs (for man holes etc) and the like etc complete all as specified and directed

M&L for preparation of new plastered surfaces of walls/ ceiling and applying two coats of oil emulsion distemper over a coat of chalk whiting all as specified and directed.

M&L for Preparation of new plaster surfaces of walls and applying two coats of weather coat (Apex) all as specified and directed.

M&L for Preparation of new wooden surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and directed

M&L for Preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed

M&L for Preparation of old distempered surfaces and applying one coat of oil emulsion distemper on walls and ceilings upto tripple storey all as specified and directed.

M&L for Preparation of old painted wooden surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint all as specified and directed.

M&L for Preparation of old painted steel surface of any description, over 10 cm in width or girth not other wise described, and applying one coat of synthetic enamel paint all as specified and directed.

M&L for Complete removal of of exiting treatment from wall and finish the undulated surface by cement putty and applying two coat of weather proofpaint (Apex) after application of one coat of primer complete all as specified and directed

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron)frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified complete all as specified and directed

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified complete all as specified and directed

M&L for Anodised aluminium with powder coating of any colour ( Not less than 50 Micron) window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for aluminium anodised powder coated (minimum thickness 50 micron) designer grill of 5-6 mm dia of mesh size 50x50mm centre to centre with 25 mm flat including aluminium beading , complete all as specified and directed.

M&L for providing cement concrete type B-0 1:2:4 (using 12.5 mm graded stone aggregate ) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

M&L for Home Sheild PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied water-proofing membrane that is highly elastic and UV resistant with 10 years warranty. ASTM D 6083-97 a waterproofing and heat reflecting system having following key performace properties : 1. UV resistant, prevent yellowing and weathering 2. Highly elastic upto 350% and crack bridging 3. Excellent adhesion on porous and non-porous substrates 4. Tensile strength > 10 N/mm2 with Geo Textile fleece 5. Soler reflective Index (SRI) more then 109-111 ASTM E 1980-11 System : First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent) Coverage :0.2kg/m2 (with 50 % dilution of water) Reinforcement : Geotextile 40 gsm Second coat : Home sheildroofkoat (or equivalent) Consumption : 0.5 kg/m2 Third coat : HS PU roofkoat (or equivalent) Consumption : 0.8 kg/m2 System buildup-1.5kg/sqm with geotextile of 40 gsm For accessible roof, tiles with scred/ adhesive may be fixed thereafter. Note :-The concerned items should be executed by OEM authorized applicator after signing of MOU (format attached as Appendix 'CD' on page no. 86 of tender documents as per Sch 'A' Note No 19 Page No 17).

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames glazed with putty or fixed with beads all as spd & directed

S&F sheet glass 3mm thick ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm each pane all as spd & directed

S&F in repair Aluminium anodised tubular curtain rod 20mm dia with bracket and dome complete all as specified and directed.

GENESIS INDIA (BID ID -3499860)

BALVINDER SINGH AND SONS (BID ID -3498192)

J P TECHNO (BID ID -3503350)

KAMAL CONSTRUCTION (BID ID -3506083)

M/s KULDEEP KUMAR CONTRACTOR (BID ID -3506076)

m/s sushila devi (BID ID -3499848)