Repair/Maint of UPS, Street lights, Nurse call system, Firealarm, OT lights etc at CHNC and other areas under GE (Utilities) Udhampur

Amount

Taking down carefully Unserviceable Security light 60 watt /Flood Light/ High Mast light fitting from pole/Structure and repair/replacement of worn out parts such as driver, SPD etc, cleaning of fittings, cover, copper wire,clamps, nuts and bolts, mounting bracket and re assembling the same after repair, testing and refixing in pole including provision of necessery T & P like ladder/Boom Vehicle to be provided by contractor, tools ets as required for taking down and refixing of street light, complete all as specified and directed by Engr-in-Charge. Note: - Replacement of defective spare parts of fitting (to make functional) will be measured and paid separately as supply only. However, cost of replacement screws, nuts, bolts, and cleaning of fittings shall be deemed to be included in quoted rate.

Description all as per serial item No 1.00 here-in-before but Flood light fittings 120 watt street light fitting, complete all as specified and directed by Engr-in-Charge.

Supply, Laying, jointing in replacement & testing 1100 Volts grade heavy duty cable PVC tape PVC sheathed 2.5 Sqmm aluminium solid conductor 2 core nominal cross section laid in trenches/fixed to walls/ passing under the roads in existing pipes etc including takind down old UNSV cable, complete all as specefied and directed by Engr-in-charge.

Supply, Laying, jointing in replacement & testing 1100 Volts grade heavy duty cable PVC tape PVC sheathed 4 Sqmm aluminium solid conductor 2 core nominal cross section laid in trenches/fixed to walls/ passing under the roads in existing pipes etc including takind down old UNSV cable complete all as specefied and directed by Engr-in-charge.

S&F in replacement modular box of size 333 x 233 x 120 mm made of FRP inpact resistance plastic & heat resistant materials including MCB SP 6 A, Connector terminal block 4 pole 16 A capacity and fixing to the street light or post top light pole with suitable sizes of clamps, nuts and bolts, complete all as specefied and directed by Engr-in-charge.

S&F in replacement MS bracket for street light fittings made out of 40 mm dia GI pipe of medium grade 1.5 mtr long each bent to required shape & size and fixed to pole with and including flat iron clamps 02 Nos made out of 32x6 mm flat iron including GI Nuts, bolts and washers and painting of clamps and street light brackets with two coat of aluminium paint over a coat of red oxide primer and fittings bracket to street light fittings, complete all as specefied and directed by Engr-in-Charge.

S&F in replacement 150 Watt LED Flood light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 110 lumen/Watt (Minimum lumen output of luminarie should be 13200 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F in replacement 120 Watt LED Flood light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 110 lumen/Watt (Minimum lumen output of luminarie should be 13200 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F in replacement 90 Watt LED street light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 100 lumen/Watt (Minimum lumen output of luminarie should be 9000 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F in replacement 60 Watt LED street light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 100 lumen/Watt (Minimum lumen output of luminarie should be 6000 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F in replacement 60 Watt inverter type LED street light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 100 lumen/Watt (Minimum lumen output of luminarie should be 6000 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F in replacement 90 Watt inverter type LED street light with pressure die cast aluminium housing & toughened glass with IP-66 degree protection, individual LED's must have peanut lenses for better throw across & along the road with luminarie efficacy of greater than 100 lumen/Watt (Minimum lumen output of luminarie should be 6000 Lumens) color rendering (CRI) of > 75 and co-related color temperature (CCT) of 5700K (+ 500K), The luminarie should have 5 KV surge protection, PF > 0.95, and total harmonic distortion of THD < 10%, voltage range of 140-280V should be provided. Luminarie should have top maintainable driver compartment for easy access to driver during maintenance. The driver used must be a constant current driver with efficiency of > 85%. Note :- The manufactures LOGO must be embossed/Engraved in the housing of the luminarie. Manufactures to provide LM80 from source manufacturer and should have adequate testing facilities approved by ministry of science (Govt of India) to provide LM 79 report, complete all as specefied and directed by Engr-in-charge.

S&F LED Bollard light 9 W in rectangular shaped victorian design with opal acrylic diffuser IP65 protection and co-related color temperature (CCT) of 3000K, complete all as specified and directed by Engr-in-Charge. Make : Bajaj Model No : BGBOS 605 9W LED WW or equivalent in Havells/Philips

Cleaning the existing exposed surfaces of steel tubular street pole of 9.0 mtr long brackets, clamps etc and painting with two coats of synthetic enamel paint (Aluminium shade) and marking pole No. with yellow paint on black base at suitable height, complete all as specified and directed by Engr-in-Charge.

Supply, laying, jointing & testing in replacement XLPE insulated, PVC bedded galvanised steel strip or wire armoured electric power cable heavy duty with stranded aluminium conductor 1100 volts grade cross sectional area 10 Sqmm 4 core laind in trenches or passing through pipe or fixed on poles, complete all as specified and directed by Engr-in-Charge.

Description all as per serial item No 15.00 here-in-before but of size 16 Sqmm 4 core, complete all as specified and directed by Engr-in-Charge.

Taking down the unserviceable LT cable of any size from tranches/ walls /floor etc, complete all as specified and as directed by engineer in charge.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of cables, pipes foundations of poles/stays/pipes etc .not exc 10 Sqm area on plan and getting out in soft/loose soil, complete all as specified and directed by Engr-in-charge

Returning, filling in excavated soil in trenches including spreading, leveling, watering and well ramming in layers n. exc. 25 cm thick, complete all as specified and directed by Engr-in-charge.

Removing of excavated soil to a distance n. exc. 50 mtr and deposited where directed at a level not exceeding 1.5 mtr above the starting point, complete all as specified and directed by Engr-in-charge.

S&F double walled corrugated (DWC) pipe of size 77/63 mm including snap fit coupler conforming to IS14930 (Pt-II)/IS16205 Pt-II for protection of LT cable in under ground, complete all as specified and directed by Engr-in-Charge.

Material and labour for making the hole under road and hard standing suitable for laying and inserting pipe upto 80 mm dia any length by mechanical drill system or Auger system and making the surface good as existing surface insulator with aluminium binding, complete all as specified and directed by Engr-in-Charge.

Supply and Laying in replacement Galvanised iron steel tubes, ISI marked light grade of size 40 mm bore for cable protection along the poles under road under drains, laid in trenches/fixed on walls/poles with suitable clamps bolts nuts etc including taking down of old unserviceble pipe, complete all as specified and directed by Engineer-in-Charge.

Opening /disconnecting the electrical connection of defective/burnt out underground LT cable of any size any core from main switch/DB/junction box / LT panel etc. Taking out the required length of cable from existing loop, cutting the defective portion of cable ,providing required thimbles/connectors at cable end and reconnecting the cable in previous location with existing main switch/DB/Junctionbox/LT panel line etc, complete all as specified and directed by Engr-in-Charge. Note:- (i) the cost of required earth work ie excavation,returning filling,relaying of sand/bricks and cost of drawing the required length from protection pipe ,breaking of required brick work/plaster/concrete and redoing the required cement work to match the existing surface is deemed to be included in quoted rates and nothing extra should be paid on this account. (ii) Additional cable/ protection pipe required at site shall be measured and paid seperatly.

S&F in replacement Power contactor 3 phase 415 Volts, 40 Amps, coil voltage of rating 240 Volts including taking down old unserviceable power contactor, complete all as specefied and directed by Engr-in-Charge.

S&F in replacement Power contactor 4 pole 240 Volts, 30 Amps , coil voltage of rating 240 Volts including taking down old unserviceable power contactor, complete all as specified and directed by Engr-in-Charge.

Supply only Driver for LED energy saving & enviornment area light fitting > 45 watts security light with active power factor correction (APFC) electronic driver. LED driver 45 Watt with operating voltage between 100-270 V of existing specifications & make, complete all as specified and directed by Engr-in-Charge.

Supply only Surge protection 5 KV devices compatible with industrial & outdoor LED fixtures upto rated power of 45 W & up to 150 W with operating voltage between 100-270 V of existing specifications & make, complete all as specefied and as directed by Engr-in-charge.

M&L for road cuttig existing road for crossing of underground electric cable for laying of any size GI tubing including necessary excavation and earth work including repairing the same as per existing with pre mix bituminious carpet, complete all as specefied and as directed by Engr-in-charge. Note: - Width of trench shall be 15 cm and depth shall be upto 30 cm.

S&F 20W ALL-IN-ONE SOLAR STREET LIGHT NG SERIES AIO Solar Street Light is made with High Efficiency Mono Crystalline So;ar PV Module, Lithium Ferro Phosphate battery with in-built BMS technology, High Efficacy LED, MPPT Solar Charger Controller and Aluminium Extruded body & is specially progrmmed to automatically control the dimming and brightness of light,which increas the backup time, complete all as specified and directed by Engr-in-Charge. Make : Havells Model No SOLAR AIO 20 W or equivalent in Bajaj/Philips

Repair/Check the serviceability of UPS of rating 20 to 30 KVA installed in various wards at CHNC including proper cleaning of dust etc from in side and out side with suction blower including replacement of minor parts such lugs /thimbles tightining of loose Battery connections etc (Spare parts shall be paid seperately), complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Supply card suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Control card suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Transformer suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Capacitor suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of PCG suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Micro controller suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Display unit suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Switching device suitable for up to 30 KVA UPS, complete all as specified and directed by Engr-in-Charge.

M&L for periodical repair / maintenance of OT Lights (Make : Hosepedia) by adjusting the mechanical and electrical driving equipment incl replacement of minor defective/spares parts/items ie lamp including complete accessories likes driver, ballast etc and wire, lugs, nut, bolts, screws etc as per existing on ground, complete all as directed to entire satisfaction of Engr-in-charge. Note : (i) The entire work and spare parts/ items shall be got executed through OEM ie Hosepedia only. (ii) The cost of all kind of minor spares parts/ items ie, nut, bolt, washer etc is deemed to be included in the quoted rates. (iii) The parts replaced shall be measured seperately under relevent item. (iv) The cost of transportation(To and from), skilled manpower and other necessary equipment shall be arranged/brought by contractor to complete the job at site only and no extra cost shall be paid to the contyractor in this effect.

Supply and fix in replacement of LED 50 Inner 8 port Circuit as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of LED 50 outer controller Circuit as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of LED 50 keypad as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of LED 50 LED's, 1 LED with LENS as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of LED 50 SMPS as per existing type suit, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of Extra sterilizable handle as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of control box as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of camera circuit Sony as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of camera as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of camera supply unit as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of Monitor as per existing type and Make, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of HD SDI splitter as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of HDMI Splitter as per existing type, complete all as specified and directed by Engr-in-Charge.

Supply and fix in replacement of DVR as per existing type, complete all as specified and directed by Engr-in-Charge.

M&L for periodical repair / maintenance of Nurse call system (Make : Medisystems) by adjusting the mechanical and electrical driving equipment incl replacement of minor defective/spares parts/items including complete accessories likes wire, lugs, nut, bolts, screws etc as per existing on ground, complete all as directed to entire satisfaction of Engr-in-charge. Note : (i) The entire work and spare parts/ items shall be got executed through OEM ie Medisystems only. (ii) The cost of all kind of minor spares parts/ items ie, nut, bolt, washer etc is deemed to be included in the quoted rates. (iii) The parts replaced shall be measured seperately under relevent item.

S&F in replacement of VDE 0834 Standard PATIENT HANDSET WITHOUT VOICE shall consist of : - Membrane Key pand with Nurse Call Button - Soft touch buttons for Optinally controll of room and bed lights - Integrated Finder and reassurance light -Antimicrobial Coating complete all as specified and directed by Engr-in-Charge.

S&F in replacement of SITC as per VDE 0834 complied BEDSIDE CONNECTION MODULE WITHOUT VOICE for connecting the patient handset shall consist of :-Mounting rail with board, 2 x RJ45 sockets for connecting the data bus -Membrane keypad with Call button and Cancel / Presence Button and integrated reassurance LED light - 1 socket with for connecting without voice Patient handset - 1 x 5 Pole DIN connector to be used as a diagnostic port - 4 x connections to be used for connecting Buttons and Lamp module - Antimicrobial Keypand complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Pull Button with integrated finder lights or reassurance light, micro switch with a 2 metre pull cord and aluminous grip with a nurse symbol printed on it, Countersunk switchbox etc., complete. Pull cord characteristics with max. force at break 120N (ca.12 kg) for hygiene reasons it must also be possible to change the pull cord very easily using a snap hook for Basic Device, 4 screw-type terminals for connecting the power supply circuit etc., complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Main Nurse station terminal capable of serving multiple call at a time with following features. - IP based 18.5 inch large LCD display - VGA or HDMI output with seperate sounder to alert nurse call. - Optional Connection of upto 2 VGA/HDMI monitors, in case double side display required. - VGA or HDMI sockets for standard monitors with VGA/HDMI input connection (Computer LCD / Flat screen monitor) or optionally HD ready TV. For TV devices without VGA input, a passive VGA/HDMI coupler can be used. . Built-in piezo buzzer for call signaling. Multiple call simultaneously visible on the screen. Single call acknowledgement button for informing patient on reciving call. Call completion only from the patient Bed, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of LAMP module For optical indication of calls, presences and reminders in the relevant colours conforming as per VDE0834 standard consisting of: - 4 light chambers with light reflectors for homogeneous illumination, - 1 light chamber fitted with 3 ultra bright red LEDs, - 1 light chamber fitted with 3 ultra bright white LEDs, - 1 light chamber fitted with 3 ultra bright green LEDs, - 1 light chamber fitted with 3 ultra bright blue LEDs, - Every light chamber conforms to the light strength set out as per VDE0834 standard, - the LED life expectancy is approximately 100,000 operating hours, complete all as specified and directed by Engr-in-Charge.

S&F in replacement of Doctor Call Button (Code Blue) with following features: 2 doctor call key (blue) including a finder light/reassurance light, - Button to be acticated simultaniously against any mis-use. - a membrane keypad - Integrated sounder - Should be connected in ring topology, complete all as specified and directed by Engr-in-Charge.

M & L for cleaning of Detectors/ MCP/ Hooter any type in any height as and when required with air blower for making all detection system healthy in any type of building, complete all as specified and directed by Engr-in-Charge.

M & L for testing of functionality of Fire Alarm System in quarterly or as and when directed by Engr- in-Charge by random check of devices by artificial smoke and other testing measures in any type of building, complete all as specified and directed by Engr-in-Charge.

M&L in repair for Reprograming of Existing fire alarm system installed at Various Locatioin including loope Checking, Changing of Device Location Name and Address of the Room and preparing as build Drawing, complete all as specified and directed by Engr-in-Charge.

S & F in repair Fire alarm control panel complying with BS EN 54 Single loop panel of capacity from 99 detectors & 99 modules upto 200 detector and modules, complete all as specified and directed by Engr-in-Charge.

Description all as per serial item No 67.00 above here-in- before, but 2 loop, complete all as specified and directed by Engr-in-Charge.

S & F in repair addressable Sounder cum- storb, complete all as specified and directed by Engr-in-Charge. Make: Edward/Honeywell/Morley/Siemens

S & F in repair addressable remote response indicators, complete all as specified and directed by Engr-in-Charge. Make : Edward/Honey well / Morley / Siemens

S & F in repair addressable Manual call point resettable type, complete all as specified and directed by Engr-in-Charge. Make : Edward/GST/Honey well/ Morley/Siemens

S & F in repair addressable Monitor module, complete all as specified and directed by Engr-in-Charge. Make : Edward / Honey well / morley / Siemens

S & F in repair Sprinkler Bulb, 20mm dia, quick response with extended covereage type 57 degree Celsius Pendent / Side wall Type, complete all as specified and directed by Engr-in-Charge.

S & F in repair addressable type heat detector with base, rate of temperature rise as per IS-2175, complete all as specified and directed by Engr-in-Charge. Make : Edward /Honey well / morley / Siemens

S & F in replacement of 12 V 65AH Battery, complete all as specified and directed by Engr-in-Charge. Make : Exide /Amaron/Panasonic.

Supply and installation including testing and commissioning of SMF Battery 12 Volts, 7.2 AH with battery copper terminals / thimples, battery inter-connection copper cable 16 Sqmm etc, complete all as specified and directed by Engr-in-Charge. Note:- Minimum Replacement manufacture warranty for 2 years.

Supply and installation including testing and commissioning of SMF Battery 12 Volts, 18 AH with battery copper terminals / thimples, battery inter-connection copper cable 16 Sqmm etc, complete all as specified and directed by Engr-in-Charge. Note:- Minimum Replacement manufacture warranty for 2 years.

Supply and installation including testing and commissioning of SMF Battery 12 Volts, 26 AH with battery copper terminals / thimples, battery inter-connection copper cable 16 Sqmm etc, complete all as specified and directed by Engr-in-Charge. Note:- Minimum Replacement manufacture warranty for 2 years.

A K ENTERPRISES ENGINEER CONTRACTOR AND GEN ORDER SUPPLIERS (BID ID -3281995)

vijay kumar gupta and co (BID ID -3287144)

FANGALIA TRADERS (BID ID -3283972)

PAUL TRADERS (BID ID -3285825)