PROVN OF SHED WITH ASSOCIATE WORKS NEAR BLDG NO -15/3 AND MINOR WORK AT

Amount

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed by Engineer-in-Charge

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m deep and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in soft/loose soil complete all as specified and directed by Engineer-in-Charge

Removal of excavated soil to a distance exceeding 500m n.exc 1.5 Km and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed by Engineer-in-Charge

M&L for Cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate in foundation filling and mass concrete complete all as specified and directed by Engineer-in-Charge.

M&L TMT bars 10 mm dia and above cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer-in-Charge.

All as per item No 06 here- in- before but 6 to 8mm dia as in stirrups, binders,spacers etc complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter flat for rough finished surface of concrete complete all as specified and directed by Engineer-in-Charge.

Formwork to sides of pillars,posts, struts, piers, columns and stanchions fair finished surfaces of concrete etc complete all as specified and directed by Engineer-in-Charge.

Formwork to sides and soffits of fair finish surfaces of concrete floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams etc complete all as specified and directed by Engineer-in-Charge.

M&L Reinforced cement concrete,type B1,1:2:4 using 20mm graded crushed stone as in Foundations, including rafts, footings, foundation beams; plinth beams and the like complete all as specified and directed by Engineer-in-Charge.

M&L Reinforced cement concrete,type B1,1:2:4 using 20mm graded crushed stone as in Columns, pillars, piers, posts and struts and the like complete all as specified and directed by Engineer-in-Charge.

M&L Reinforced cement concrete,type B1,1:2:4 using 20mm graded crushed stone as in Beams, cantilevers, bressummers, lintels over 1.5m span and the like complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with sub-class `B' bricks, straight or curved on plan exceeding 6 M mean radius built in cement mortar 1:6, except brick all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for Rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or on concrete surfaces finished even and smooth without using extra cement including mixing intergral water proofing compound in the proportion as mentioned in manufacturer's instructions complete all as specified and directed by Engineer-in-Charge.

Supply only integral water proofing compound of approved manufacturer complete all as specified and directed by Engineer-in-Charge.Charge.

Preparation of newly plastered surfaces of walls and applying two coats of cement base paint of any colour or tint as ordered on surfaces of wall including cornices complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of new plastered surfaces of walls and applying two coat of oil bound distemper over 2-3mm thick wall care putty applied in two coats to obtain the smooth surfaces with a coat of primer complete all as specified and directed Engineer-in-Charge.

S&F Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe 410-W (Gde-E- 250) quality- A complete all as specified and directed Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws,complete all as specified and directed by Engineer-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 mpa as in ridges/eaves board, fixed with self tapping screws,complete all as specified and directed by Engineer-in-Charge.

Material & Labour for hardcore of broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15cm thick, watered and remmed to a true surface, complete all as specified and as directed by the Engineer-in-Charge

Material & Labour for 100mm thick Plain cement concrete 1:4:8 type D2 (using 40 mm graded crushed stone aggregate) as in sub base /mass fiiling in foundation complete all as specified and directed by Engineer-in-Charge.

M & L for Forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound complete all as specified and directed by Engineer-in-Charge.

M & L for Machine cut kota stone slab 20-25mm thick as in flooring,steps of stair (treads) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over including screed bed or bedding layer of mortar 20 mm thick in CM 1:4, Complete all as specified and directed by Engineer-in-charge.

M&L for Plain cement concrete 1:3:6, type C-1 using 20mm graded stone aggregate, 50mm thick, as in Plinth protection and finishing the surface even and smooth without using extra cement and filling the joints with mastic filling i.e one part of bitumen 85/25 & 3 parts of sand by weight complete all as specified and directed by Engineer-in-Charge.

M & L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as for holdfasts, etc including necessary formwork, complete all as specified and directed by Engineer-in-Charge

S&F Factory made box type steel window with two nos 150mm mild steel tower bolts to eachshutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEAF/STD-184-2012 sheet 1/3 to 3/3.

S&F Factory made box type steel window with two Nos 150mm mild steel tower bolts to eachshutter, steel handle and without glazing bars, including flat iron 12 x 3 mm for securing wire mesh, dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEAF/STD-185-2012 sheet 1/2 to 2/2.

S&F stainless steel wire cloth,0.36mm nominal dia of wire and average width of aperture 1.40mm fixed to steel frames with stainless steel tacks, or stainless steel wire staples, or fixed to wooden frame with first class hard wood bead, complete all as specified and directed by Engineer-in-Charge.

Supply & fix, sheet glass 3mm thick, ordinary quality glazing with oil putty or wooden bead in squares not exceeding 0.5Sqm in each pane,complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Mild steel Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks;chowkhats and similar work conforming to Fe 410-0 or Fe 310-0, complete all as specified and directed by Engineer-in-Charge.

S&F 1.25mm thick Steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated,complete: push pull or manual type complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Sand filling under floors or in paths/under tiles including watering and consolidation, complete all as specified and directed by Engineer-in-Charge.

Material and labour, factory made pre cast cement concrete 1:2:4 type B-1 usinng 20mm graded crushed stone aggregate, of size approved by GE, kerb stone compressed & hydaulically pressed, tapered/curved on one edge at top, laid on edge with 150mm wide bedding layer 25mm thick sand and pionted in cement mortar 1:4 vertically on sides of path/road/pavements, including form work, necessary excavation and earth work,Complete all as specified and directed by Engineer-in-Charge.

Material and labour for factory made, precast concrete, machine pressed, interlocking paver block any shape and size, ISI marked, conforming to IS 15658-2006, of 80mm thickness, M-40 Grade, with grey cement and no pigment , Complete all as specified and directed by Engineer-in-Charge. Note: 1.The shape/size of paver blocks shall be as approved by the GE

M&L for preperation of new concrete surface of any description, over 10cm in width or girth,not otherwise described and applying two coat of synthetic enamal paint (Black and Yellow/ Blue or White) including over a coat of plaster priming paint complete all as specified and directed by Engineer-in-Charge.

Preparation of new or previously untreated steel surfaces of steel of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed by Engineer-in-Charge

Demolition of PCC in ground floors and pavings n exc 15 cm thickness (below or above ground level) and removal of rubbish out MoD land Complete all as specified and directed by Engineer-in-Charge.

M&L for 25 mm thick PCC 1:2:4 type B0 (Using 12.5 mm graded crushed stone aggregate) as floorings finished even & rough to receive the bedding mortar Complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Vitrified coloured tiles 10mm thick (Square/ Rectangular) polished area of each tile exceeding 0.36 Sqm and not exceeding 0.42 Sqm in floors set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including screed bed or bedding layer 15mm thick in cement mortar 1:4 for laying tile. complete all as specified and directed by Engineer-in-Charge.

Material & Labour for Vitrified coloured tiles 10mm thick (Square/ Rectangular) polished area of each tile exceeding 0.36 Sqm and not exceeding 0.42 Sqm in skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match,over and including rendering of 10mm thick in cement mortar 1:4 for laying tile. complete all as specified and directed by Engineer-in-Charge.

S&F 3mm thick figured glass, pin head type and glazing with oil putty in squares in exc 0.5 sq.m in each pane complete all as specified and directed by Engineer-in-Charge.

M&L for preperation of old plastererd wall surfaces and applying two coat of oil bound distemper complete all as specified and directed by Engineer-in-Charge.

M&L Point wiring with 1.5 sq mm copper conductor FRLS (multistranded) PVC insulated ISI marked unsheathed cable 1100 volts grade in and including concealed/surface , non metalic rigid PVC medium grade ISI marked conduit not less than 19 mm with all fittings & other accessories including PVC insulated ISI marked unsheathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly concealed in wall/ceiling, MS box 1.6 mm thick with hylum sheet 3 mm thick (approved colour) suitable size switches, sockets, fan regulator etc for the following :- Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green) (a) One light/fan point controlled by one way switch

S&F switch paino type, 5 Amp, single pole one way 230 Volts, flush type complete all as specified and as directed

S&F ceiling rose , surface backelite, three terminal AC 230 Volt complete all as specified.

M&L for Point wiring with 2.5 sq mm copper conductor FRLS (multistranded) PVC insulated ISI marked unsheathed cable 1100 volts grade in and including concealed/surface , non metalic rigid PVC medium grade ISI marked conduit not less than 19 mm with all fittings & accessories including PVC insulated ISI marked unsheathed FRLS cable 1100 volts grade of size 1.5 sq mm copper conductor as earth wire to common earth dolly concealed in wall/ceiling, MS box 1.6 mm thick with hylum sheet 3 mm thick (approved colour) suitable size switches, sockets, fan regulator etc complete as specified and directed :- Note - Colour code of cable Phase-Red Neutral- Black and Earth -Green)

Supply & Fixing Switch piano, flush type, single pole, one way, 15 Amp 230volts complete all as specified and directed by Engineer-in-Charge.

Supply & Fixing Socket outlet multipurpose 3 pin 5 Amp & 15 Amp, flush type, complete all as specified and directed by Engineer-in-Charge.

S&F LED tube light fitting 1x20watt 230 volt basic all purpose surface and wall mounted led battern with aluminium square profile and integraeted electronic driver, pre wired and fixed on walls with all fittings accessories such as screws, clips etc and connecting up with two core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge Make Havells(Luminline)LUMILINEBS20WLED 830 SPCWH or equivalent of Wipro /Crompton Greves.

S&F New generation energy saving and environmental friendly long life 15 watt LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP65 protection and impact resistance of IK07 complete all as specified and directed by Engr-in-charge. Make Havells Cat No. ENDURAPEARLSL15WLED757SASYTOPC or equivalent of Wipro /Crompton Greves.

S&F for Epoxy powder coated or polystrene insulated material sheet metal enclosure factory made (double door) 4 way SPN suitable for MCB DB's 240 Volts with 200 Amps rated busbar, neutral & earthing link bar, flush/surface mounting complete all as specified and directed.

S&F for MCB single pole and neutral (ISI marked) `C' series working on 240 volts 50HZ AC supply for incoming & out going controlling system of capaicty 40-63 Amps 10 KA breaking capacity all as specified and directed.

S&F MCB single pole ISI marked `C' series working on 240 Volts 50 HZ AC supply for incoming and out going controlling circuit of capacity 6-32 Amps breaking capacity 10 KA etc all as specified and directed.

Supply, laying, jointing, testing XLPE insulated PVC sheathed with stranded aluminium conductor heavy duty, conforming to IS 1554 Part I / ISI marked, including cable glands , cable lugs etc as suitable to the cable size, cables to be laid in trenches, fixed along the poles bare or through GI pipe laid under floors road etc fixed concealed in walls encased in GI pipe etc complete of following size: (a) 10Sqmm 2 core

Supply and fixing galvanised iron tube ` light grade' with all fittings for duct/road/trench/wall for 40 mm dia of pipe complete all as specified and directed Engineer-in-Charge.

M&L for sand cushioning in trenches spreading and consolidation 8 cm thick before laying the cable and 15 cm of the sand after laying the cable but will be measured 18 cm after punning etc complete as specified and directed.

M&L for laying of bricks well burnt sub class B (old pattern) laid flat for cable protection width equal to the length of bricks complete all as specified and directed

Material & labour for earthing complete with galvanized steel earth plate electrode 60 cms x 60 cms x6.00mm thick buried directly in ground vertically to a depth not less than 2.25 meter below ground level with top edge of the plate not less than 1.5 metre below normal ground level earth plate surrounded by 15 cm thick and packed alternate layers of charcoal dust and common salt, earth lead wire 4.0 mm by means of bolts ,nuts ,check nuts and washers of galvanized iron or steel and thimbles and other end of the earth wire connected to main switch board and protected by galvanized iron or steel pipe light grade 15 mm bore and water pipe 20 mm bore GI light grade (ISI marked ) with funnel and wire mesh ,including all necessary excavation and earth work PCC chamber in cement concrete 1:3:6 type C-2 and RCC cover and all as shown in electrical plate No 5 of MES Sch Part-1 (2009), complete all as specified.

Baba Engineers and Contractors

SYNDICATE BUILDERS

aggarwal contractors and engineers