CONSTRUCTION OF 2 BLOCKS OF 75 SINGLE BEDDED BOYS HOSTEL AT IARI CAMPUS DHEMAJI ASSAM

Amount

EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.

All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge.

Ordinary rock

Hard rock (blasting prohibited)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials.

All kinds of soil (From 1.50 to 3.00 mtr)

Supplying and filling in plinth with local sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified.

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POSTCONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) :

Along external wall where the apron is not provided using chemical emulsion @ 7.5 litres / sqm of the vertical surface of the substructure to a depth of 300 mm including excavation channel along the wall & rodding etc. complete:

With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor :

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

Pipes, cables etc, not exceeding 80 mm dia.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shttering - All work up to plinth level

1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size).

1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

REINFORCED CEMENT CONCRETE

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering & shuttering including strutting, propping etc. and removal of form work for:

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Stairs, (excluding landings) except spiral-staircases

Edges of slabs and breaks in floors and walls

Under 20 cm wide

Steel reinforcement for R.C.C. work ncluding straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).

Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, upto 25 metre height, above ground level, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose.(2) The payment will be made once only for execution of all items for such works.

Design Mix

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.( minimum 40% opc cement )

All works upto plinth level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level upto floor V level

Concrete of M25 grade with minimum cement content of 330 kg /cum

Concrete of M30 grade with minimum cement content of 350 kg /cum

Extra for providing richer mixes at all floor levels.

Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/ cum)

Extra for R.C.C./ B.M.C/ R.M.C. work above floor V level for each four floors or part thereof.

FLOOR

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components.System shall consist of metal profiles with a universal aluminum base member designed to ccommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self – centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge . (Material shall confirm to ASTM 6063.)

Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shallutilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement.(Material shall confirm to ASTM 6063.)

Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufacture for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates as per ASTM B221-02. The system shall be such that it provides water tight roof to roof /roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments.

The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.)

Roof Joint of 100 mm gap

Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as per design for expansion joints.

200 mm wide.

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing with cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.

25 mm thick

BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:4 (1 cement : 4 coarse sand)

Extra for brick work / AAC block masonry / Tile brick masonry in superstructure above floor V level, for each four floors or part thereof by mechanical means.

floor

HALF BRICK MASONRY

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.

Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for half brick masonry in superstructure, above floor V level for every four floors or part thereof by mechanical means.

floor

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

Providing and laying autoclaved aerated cement blocks masonry with 100 mm thick AAC blocks in super structure above plinth level up to floor V level in cement mortar 1:4 (1 cement : 4 coarse sand ). The rate includes providing and placing in position 2 Nos 6 mm dia M.S. bars at every third course of masonry work.

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineerin- Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Brick edging 7cm wide 11.4 cm deep to plinth protection with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including grouting with cement mortar 1:4 (1 cement : 4 fine sand).

WOOD WORK

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately).

Saal wood

Kiln seasoned and chemically treated hollock wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of doorshutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete :

2nd class teak wood

Providing and fixing teak wood lipping of size 25x3 mm in pelmet.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed onthe body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing wooden moulded corner beading of triangular shape to the junction of panelling etc. with iron screws, plugs and priming coat on unexposed surface etc. complete 2nd class teak wood.

50x50 mm (base and height)

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Single rubber stopper

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2 mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady] the frame.

Providing and fixing to existing door frames.

30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming to IS: 14856, including fixing to frames.

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter. The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight) with stainless steel screws etc. complete :

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door Machine, handle, lock and stopper etc. including ).

ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P.brass / stainless steel screws, all complete as per architecturaldrawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the costof EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/ sqm)

STEEL WORK

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position andmapplying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.

Electric resistance or induction butt welded tubes

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

FLOORING

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge

Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc.complete.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand), laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for pre finished nosing in treads of steps of Kota stone/ local stone slab.

Extra for Kota stone/ sand stone in treads of steps and risers using single length up to 1.05 metre

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Cement plaster skirting up to 30 cm height, with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement.

18 mm thick

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed Vitrified tiles Matt/Antiskid finish of size

Size of Tile 600 x 600 mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete.

Size of Tile 600x600 mm

Size of Tile 800x800 mm

Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Glazed vitrified floor tiles polished finish of size

Size of Tile 1200 x 1200 mm

52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

40 mm thick fine dressed stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints finished flush.

Red sand stone

Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

ROOFING

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design :

In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and erimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :

Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and pattern as approved by the Engineerin- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60

Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling up to a height of 5 m above floor level, over first class kail wood strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame (frame work to be paid separately):

Flat Surfaces

Providing and fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50x50x3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shape wherever required.

FINISHING

12 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement : 4 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement : 4 fine sand)

6 mm plaster on cement concrete or reinforced cement concrete work with white cement based polymer modified self curing mortar of approved make as per the direction of Engineer-In-Charge.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.

Two coats

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with 100% Premium Acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives.

New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with textured exterior paint of required shade :

New work (Two or more coats applied @ 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied @ 2.20kg/10 sqm

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture

WATER PROOFING

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of :

Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound.

2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions.

Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer.

Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge :

Using rough kota stone.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :

First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.

Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, erraces etc consisting of following operations:

Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment.

Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Eng ineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs.

After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge.

Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep.

The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as directed and specified by the Engineer-in-Charge :

With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

STRUCTURAL GLAZING ALUMINIUM COMPOSITE PANEL

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthened clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.“(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2)“For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.“

Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approvedmshop drawings , the aluminium quality as per grade 6063 T5 or T6mas per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it water tight.

Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, abour for fabricating and installation of aluminium grid, installation ofglazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified.The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge

Note:- 2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

(1) Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr. (2)Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331-09 testing method for a range up to 2000 ml. (3)Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml

(4) Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm (5)Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test. Tests to be conducted on site. (6)Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge

MISCELLANOUS WORK

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earthwith lead upto 50 metres.

Supplying and stacking at site.

63 mm to 45 mm size stone aggregate

Stone screening 13.2 mm nominal size (Type A)

Good earth

Laying water bound macadam sub-base with brick aggregate and binding material, earth etc. including screening, sorting and spreading to template and consolidation with light power road-roller etc. complete.(payment for brick aggregate and moorum etc. to be made separately)

Over burnt (Jhama) brick aggregate 90 mm to 45 mm

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge

Providing and laying at or near ground level factory made kerb stone bof M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

N.S. ITEM

FINISHING

Chicken Mesh : P/F hexagonal chicken mesh having opening 20mmx20mm of 26 gauge at juncitons of concrete & brick work or between different material etc. as approved by architect and complete in all respect.

supplying and Filling of sunk portion with cinder of required height including levelling and dressing the surface

ELEVATION

Providing and fixing tiles 230X75 MM sizes approved make,UNISTONE BRICK in COPPER/RED colours & shade, in ELEVATION WORK, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete.

Wet cleaning of stone e levation with High Pressure Jet with minimum 120 bar pressure to wipe out foreign particles on the surface and then allow the surface to dry for at least 24 Hours .As a second step, providing and applying " Efflorescence prohibitor , anti fungal water pepellent Coating " meant for herita ge building and having accreditation of Central Building Research Institute Roorkee on the st one elevation wall by spraying complete in all respect and heights ov er stone elevation .The work would be carried out all complete as per direction of the Engin eer in charge.

WOOD WORK

Providing & fixing of Roller Blinds (Blackout) on the windows at all heights, as approved by architect and complete in all respect. Note:- The blind is 100% Polyster with thickness of 0.45 mm

Providing & fixing of wooden Blinds for all windows with 35 mm to 50 mm wide with mechanism in which lifting & tilting is done by same cordian as approved by architect and complete in all respect.

providing & Fixing of Roman Blind for all windows with 0.40 mm thickness and one touch down system with one cord and suitable for Moist environment as approved by architect and complete in all respect.

Providing & Fixing of Rooler Blind Perforated Screen Fabric on the windows at all heights as approved by architect and complete in all respect.

Gym flooring

Providing , Laying and installation of 20mm thick Crum Rubber tiles in Gym Flooring with Model 5003.

Supply & Fixing Sports Flooring in Play Area includes Shock absorption,Sliding Coeffiecient, impact Resistance Properties or as approved by architect and complete in all respect.

DOOR FITTING

Providing & Fixing Stainless Steel Indicating Bolt & Dead Bolt, SS Plate Black Body with SS Finish Lock as approved by architect and complete in all respect.

Providing & Fixing Mortise handle in SS304 Pipe with 22mm dia & latch with SS Front & Strike Plate as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing & Fixin Pull & Mortise handle in SS304 Pipe with25mm & 22mm dia respectively + lockbody with SS Front & Strike Plate, Heavy Duty Springs, Anti Corrosive Plating, Double Throw Deadbolt, Brass follower for mortise rod + 5 Pin Euro Profile Cylinders, 3 Brass Keys, EN Standard, 2 Lakh Cycle Tested as approved by architect and complete in all respect.. 10"x25mm Pull / 100 ss 50x85mm / 09 ss 60mm)

Make- Pag, doorset, Yale

Providing & Fixing Plasma pull handle in SS304, 10" length & 22mm dia as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing & Fixing Redfire pull handle in SS304, 12" length & 22mm dia as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing n& Fixing Heavy Deluxe Tower Bolt (10") in SS304 with Front Fixing Screws as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing n& Fixing Heavy Deluxe Tower Bolt (6") in SS304 with Front Fixing Screws as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing & Fixing Sign Plates 170 mm stainless steel as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

Providing & fixing Double door Lock with cylinder 10 to 12 mm Glass Left,right complete as approved by architect and complete in all respect.

Make- Pag, doorset, Yale

PLUMBING WORKS

SANITARY INSTALLATIONS

Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast P or S trap, 10 Litre low level P.V.C. flushing cistern with manually controlled device(handle lever) conforming to IS:7231, with all fittings & fixtures complete including cutting and making good the walls and floors wherever required.

White vitreous chinaOrissa pattern W.C. pan of size 580x480mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350mm with white PVC automatic flushing cistern with fittings,standard size C.P.brass flush pipe,spreaders with unions & clamps(all in CP brass)including painting of fittings, cutting and making good the walls and floors where required.

a) Single half stall urinal basin with 5litre automatic flushing cistern.

b) Range of two half stall urinal basin with 5litre automatic flushing cistern.

c) Range of three half stall urinal basin with 10 litre automatic flushing cistern.

Providing and fixing wash basin with CI brackets,15mm brass pillar taps,32mm CP brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required.

White vitreous china wash basin size 550 mm x 400 mm with single 15mm CP brass pillar tap.

Providing and fixing kitchen sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P. brass waste complete, including painting the fittings and brackets, cutting and making good the walls wherevern required:

White glazed fire clay kitchen sink of size 600x450x 250 mm

Providing and fixing Stainless steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittingsand brackets, cutting and making good the walls whereve required.

Kitchen sink with drain board

510 X 1040 mm bowl depth 250mm

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing P.V.C waste pipe for sink or wash basin including P.V.C waste fitting complete .

Flexible pipe

a) 40 mm dia

Providing and fixing 100mm sand cast iron grating for gully trap.

Providing and fixing 600x450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing toilet paper holder.

a) CP Brass

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors

100 mm inlet and 100 mm outlet

Sand cast iron S&S as per IS: 3989

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour.

Waste coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms

Providing and fixing PTMT liquid soap container 109 mm wide,125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.minimum water seal, weighing not less than 263 gms

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm wide with minimum distances of 37 mm from wall face with concealed fittings arrangement of approved quality and colour,weighing not less than 88 gms

Providing, Fixing,testing and commissioning of 15 mm dia CP brass two way bib cock with flow 6 LPM (Litre per Minute) at 3.1 bar or 45 psi test pressure with C.P. wall flange of approved quality as approved by architect and complete in all respect.

Providing & fixing S.S. health faucet for ablution with 1.2 meter long PVC tube, hand shower, couplings, wall hook and other accessories of quality and make as approved by architect.

INTERNAL DRAINAGE

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing to the inlet mouth of rain water pipe, cast iron grating 15 cm diameter and weighing not less than 440 gms

Providing, fixing, jointing, testing and commissioning UPVC (Class B) Rain water downtake pipe conforming to IS:13592 cut to required lengths including all necessary fittings and specials.UPVC fittings (moulded as well as fabricated) like bends, tees, Y-tees, crosses, boss connections, access pieces, saddle pieces, cleanouts, adaptors for connections to other materials, plugs, reducers, cowls, offsets and other specials. Fixing at wall/ceiling level supported by galvanized steel clamps & hangers etc. Making proper connection with cement solvent joint as per BIS / manufacturer. Cutting, chases / holes in floors / walls / slab and making good wherever required. (All major MS structure to hold the stack with fixing including anchor fasteners,sand, cement etc is included in this item).

110 mm dia

Providing, fixing, jointing and testing UPVC soil, waste, vent pipework comprising UPVC pipe conforming to IS :4985-1983 of class 3 ( 6kg/cm2) as specified below and fittings (moulded as well as fabricated) like elbows, bends, reducers, threaded tail pieces, caps, suitable elbow with suitable extension piece for drain point and other specials jointing with cement solvent, chasing, cutting and making good the walls & floors pipes laid in floors shall be encased with 40 mm thick concrete all around, complete in all respects including testing of complete installation.(All major MS structure to hold the stack with fixing including anchor fasteners, sand, cement etc is included in this item) as approved by architect and complete in all respect.

40 mm dia 6 kg/cm2 (Class III )

50 mm dia 6 kg/cm2 (Class III )

75 mm dia 6 kg/cm2 (Class III )

110 mm dia 6 kg/cm2 (Class III )

Providing and fixing UPVC/SWR trap (P trap) of self cleaning design as per IS:13592 : 1992 complete including cost of cutting and making good the cutouts in walls and floors etc.including cutting and making good the walls and floors wherever required complete as approved by architect and complete in all respect. as approved by architect and complete in all respect.

110 mm inlet and 110 mm outlet

Providing and fixing floor drain made out of 110x50 mm OD uPVC. elbow connected to uPVC pipe complete as per direction of Project Manager as approved by architect and complete in all respect as approved by architect and complete in all respect.

Providing and fixing Balcony drain made out of 50 mm OD uPVC. elbow connected to uPVC pipe complete as per direction of Project Manager as approved by architect and complete in all respect as approved by architect and complete in all respect.

Providing and fixing P.V.C. WC connector (straight or bend type) with rubber lip ring. Including 110 mm dia PVC pipe / bend of required length and proper connection with M seal to C.I. pipe complete as required as approved by architect and complete in all respect..

Providing and fixing Inlet Fitting for Urinal trap, formed out of 110 mm PVC pipe with multiple side inlets formed with saddle pieces, suitable for 40, 50 and 63 mm dia side connections as per standard detail and support through galvanized steel support from slab or set in cement concrete mix 1:2:4 including cutting and making good the walls and floors wherever required as approved by architect and complete in all respect..

Providing and fixing Heavy Class Cockroch Type SS grating of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT, UT as approved by architect and complete in all respect..

Size 127 mm X 127 mm

Providing and fixing Heavy Class SS grating of approved design including setting in floor with cement motor to match with floor finish as per architect requirement suitable for waster and FT, UT & FD as approved by architect and complete in all respect..

Size 100 mm X 100 mm

Providing and fixing cleaning eye 110mm dia on horizontal UPVC soil & waste pipes of 300 mm long UPVC pipe with one plain end lead caulked in to the collar of UPVC pipe and the other end with flange which in covered by neoprene rubber gasket and blank flange, complete with nuts, bolts etc and hot dip galvanization after fabrication to the satisfaction of Project Manager as approved by architect and complete in all respect..

110 mm dia

SUB HEAD III: WATER SUPPLY

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all (CPVC) plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. .

Internal Work - Exposed on Wall

15 mm outer dia pipes.

20 mm outer dia pipes.

25 mm outer dia pipes.

32 mm outer dia pipes.

40 mm outer dia pipes.

50 mm outer dia pipes.

Providing and fixing Chlorinate Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This including jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the the same including testing of joints complete as per direction of engineer in charge.

Concealed work Including cutting chases and making good the walls etc.

15 mm outer dia pipes.

20 mm outer dia pipes.

25 mm outer dia pipes.

32 mm outer dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This including jointing of pipes & fittings with one step CPVC solvent cement trenching refilling& testing of joints complete as per direction of engineer in charge.

External Work

32 mm outer dia pipes.

40 mm outer dia pipes.

50 mm outer dia pipes.

Providing and fixing GI complete with GI fittings including trenching and refilling etc.

External Work

50 mm dia nominal bore.

65 mm dia nominal bore.

80 mm dia nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end):

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

65 mm dia nominal bore

80 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :

20 mm nominal bore

25 mm nominal bore

Providing and fixing uplasticised PVC connection pipe with brass unions :

30 cm length

15 mm nominal bore

Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet :

150 mm diameter

Providing and fixing C.P.brass bib cock of approved quality conforming to IS : 8931.

Providing and fixing C.P.brass long body bib cock of approved quality conforming to IS standard and Weighing not less than 690 gms.

15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

15 mm nominal bore.

Providing and fixing C.P. bass angle valve for basin mixer and geyser points of approved quality conforming to I.S:8931 a) 15 mm nominal bore

15 mm nominal bore

Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

SUB HEAD IV: DRAINAGE- EXTERNAL

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :

All kinds of soils.

Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design :

150 mm diameter S.W. pipe

250 mm diameter S.W. pipe

Providing and fixing square-mouth S.W. gully trap Class SP-1 complete with C.I. grating brick masonry chamber with grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design :

150x100mm size P type

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

180x150mm size P type

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.

100 mm dia R.C.C. Pipe

150 mm dia R.C.C. Pipe

250 mm dia R.C.C. Pipe

300 mm dia R.C.C. Pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand), R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation in cement concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :

Inside size 90 x 80 cm and 45 cm deep including C.I. cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg).

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Inside size 120 x 90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg).

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Extra for depth for manholes

Size 120x90 cm

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :

0.91 m deep with S.F.R.C. cover and frame (heavy duty, HD-20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :

With Sewer bricks conforming to IS : 4885

Providing and constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C. horizontal grating with frame complete as per standard design.

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 45x45x77.5 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand ) with precast R.C.C. vertical grating complete as per standard design :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and constructing brick masonry chamber for undergroundCI inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design :

Inside dimensions 455x610 mm and 45 cm deep for single pipe line :

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

Extra depth beyond 45 cm of brick masonry chamber:

For 455x610 mm size

With common burnt clay F.P.S (non - modular) bricks of class designation 7.5

SUB HEAD V:

Providing & fixing in position storage type hot water electrical geyser including making connection in all respects.-15 litres capacity

Providing & fixing in position storage type hot water electrical geyser including making connection in all respects.-35 litres capacity

Providing & Fixing Voltas Stainless Steel Water Cooler, 80 Liter,Silver Size:550x560x1470mm

Providing and fixing SS chamber ( GREASE TRAP ) with proper partition as shown of the capacity and size . The lengh should be 3 feet , width 2 feet and height 2 feet. The initial catchment of ss net box for hard partials and given distance overfloe partition. The with bothe side 4 inch dia ss pipe welded with proper threads at both the ends matching to FT pvc 4" dia size pipe.

SUB-HEAD I : FIRE FIGHTING SYSTEM

PUMPS

Supplying, installation, testing and commissioning ofelectric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump)

Horizontal type, multistage, centrifugal, split casingpump of cast iron body & bronze impeller with stainless steel shaft, mechanical confirming to IS : 1520.

Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot mounted type with Class-'F' insulation, conforming to IS-325

M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as required.

Suitable cement concrete foundation duly plastered and with anti vibration pads.

900 lpm at 35 m Head

PIPES & ACCESSORIES

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

80 mm dia

100 mm dia

150 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :

Single headed Gunmetal

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

80 mm dia

100 mm dia

150 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

40 mm dia

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber qasket, GI bolts, nuts, washers etc.as required :

100mm dia

150mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :

Gun Metal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required; -20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 -20 mm nominal internal dia gun metal globe valve & nozzle. -Drum and brackets for fixing the equipmets on wall. -Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :

Gun Metal

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and painting with synthetic enamel paint of approved shade as required.

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing and placing on terrace (at all floor levels) Polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement amd making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Providing and fixing Fire Extinguishers complete with all accessories as per manufacturer's specifications.

a) Water CO2 nozzle type. 9 Lt.capacity (IS:15683)

b) ABC dry powder stored pressure type 6 kg. capacity (IS:15683)

c) Mechanical Foam (AFFF) complete as required capacity - 9 ltr , 15683- 2006 & ISO - 9001

Supply, Installation, Testing and Commissioning of 100 mm dia Bourden type, Stainless Steel dial type Pressure Gauge including brass isolation valve and siphon pipe having calibration of 0-16 Kg / cm2 .as approved by architect and complete in all respect..

Supplying and fixing air realease valve made of 25 mm dia on top and flanged connection to riser with required accessories, paintingwith synthetic enamel paint of approved shade as required.

Providing & Fixing of MS Fire Hose Cabinet (2100 X 1200 X 600)mm, Fabricated from 14 Gauge MS Sheet, 5mm Thick Glass , Double Door with Locking Arrangement , powder coated (Make- Exflame)

ELECTRICALS WORKS

11KV H.T. VCB PANEL (INCOMING CUM OUTGOING)

800 A Vacuum circuit breaker of 26KA ruputuring capacity at 11 KV rated, totally enclosed, air insulated metal clad housing, floor mounting, horizontal isolation, vermin proof, fully interlocked horizontal drawout type having isolation features and control devices complete with the following:

Single Phase double core current transformer 50/25/5 Amp epoxy cast insulated class of insulation E.

Core 1-10VA burden class 1.0 for metering.

Core 1-10VA burden class 5P10 for protection.

P.T's of 11KV/1.732, 110V/1.732, 100VA with suitable rating H.T. & L.T. fuse conforming to relevant IS Standards and complete as required.

One no. numerical microprocessor based three phase over current (IDMT Relay) (1 O/C+1E/F) with earth fault relay with instantaneous elements.

1 No. Anti Pumping device.

1 No. Circuit breaker control switch for electrical (T/N/C).

1 No. limit switch for test & service position.

1 No. Digital Multifuction Meter With RS 485 Port.

1 No. electronic type digital energy analyser having 30 days memory and parameters of KW, KWH, Power factor, frequency etc. Suitable for BMS compatible with all accessories.

1 Set of following indicating lamps.

Red, Yellow & Blue for phase indication.

Amber for Trip indication.

Red `ON' Green `OFF'

Spring charge indication.

Auto trip indication.

1 No. hooter with hooter acceptance and reset push button.

1 no. Numeric relay

1 no. master trip relay similar to PQ8 (ABB) or equivalent.

Trip circuit supervision relay similar to TCS or equivalent.

630A color coded heat shrinkable sleeved TP Copper busbar .

1 Set of fuses, ferrules, wiring etc. as required.

Note: All spare contacts of breaker or any other equipment inside the breaker shall be wired upto the outgoing terminal strip with appropriate ferrules/ coding. The terminal strip rating shall be suitable for connecting two wires of 2.5sqmm subjected to providing minimum size strip suitable for 4/6sqmm.

1 No. power pack (110V AC to 24V DC) with sealed maintenance free batteries suitable for 24V DC load of full VCB board.

TOTAL OF 11KV HT PANELS

250 KVA, 11KV/ 415V COMPACT SUB-STATION (CSS)

Supply, installation, testing & commissioning of 250 KVA 3 phase Compact sub-station including all allied fittings & fixtures of LT Part as per direction of Engineer-in-Charge duly certified & tested by Govt. Laboratory and approved brand as per direction of Engineer-in-Charge

TOTAL OF 250 KVA COMPACT SUB-STATION (CSS) TRANSFORMER

250 KVA DIESEL GENERATING SET:

Radiator Cooled DG sets of following capacity (250 KVA) compact packaged silent type, with Outdoor type Acoustic Enclosure to reduce the noise level as per requirements of central pollution control board, 415Volts, 3 phase, 50 Hz AC alternator coupled to diesel engine with Electronic Governer Suitable for Auto Load Sharing and Auto Synchronizing System complete with all accessories, standard specifications tool kits, service manual, self starting device, fly wheel, coupling with guard, V velt, radiator, instrument panel (starting switch with key, Water Temperature indicator gauge, Lub OIl Pressure gauge, Lube oil temperature gauge, Battery Charging Ammeter, indicating lamp, hour counter etc.), hospital silencer, common bed plate, anti vibration isolation pads, extended cable termination box, grouting bolts, first charge of engine oil, gear oil, high speed diesel oil, 24 volt maintenance free chargeable battery set with Trickle/Boost Battery charger, interface card for BMS connectivity complete as required of rating 415 Volts, 3 phase, 50 Hz. AC alternator coupled to Diesel Engine complete with all accessories. NOC from concerned goverment authority for installation and operation of D.G. set shall be taken by contractor.As per latest CPCB -IV.

Air cleaner and air suction pipe

Exhaust manifold with flexible bellow

Air Cooling system complete with engine driven fan, to connect diesel engine to Radiator with thermostat

Automatic ‘stop’ device if any of the following parameters are varied beyond upper/ lower limits, with visual indication

Low- lube oil pressure

Cooling water temperature (High)

Over- Speed

Over crank

Circuit breaker within canopy - 1No. MCCB (25kA) Thermal Magnetic based release with built in over Load & short circuit & E/F Protection.

Note: Both DG sets run in Solo mode but provision required synchronization in Future.

250 KVA D.G. Set with suitable capacity of day oil fuel Tank

UPS SYSTEMS

Design, manufacturing, assembly, testing at works, supply, receiving at site, erection, testing and commissioning of true-online double conversion VFI Technology UPS, 1Ph/1Ph. AC input & 1Ph/1Ph AC output UPS system suitable for 220VAC, 50Hz supply, variation +/-1% , PF 0.8 as required as per specification and consisting of following:

Input range should be 220V AC-260V AC, in case the voltage range does not meet the specified range, cost of servo stabilizer should be added.

IGBT Rectifier Modules to achieve less than 2% Input Current distortion and greater than 0.98 PF at Input at all loads

Fully microprocessor based with diagnostics capability.

Dual Input (Separate Input for rectifier and separate input for Bypass)

Required quantity and details of UPS are as mentioned below. Location details and mode of operation of UPS shall be as per SLD.

Design, manufacturing, testing at works, supply, erection, testing and commissioning of One sets of SMF VRLA battery with each UPS capacity as mentioned below, having back up time as mentioned below at full load, with interconnecting cables, cabinets and standard accessories as per specification and as required for the UPS system. (12V Cells)

Battery shall be external type with rack and suitable for 30 minute backup on 100% load. Battery to be inbuild in UPS.

UPS shall be compatible for Parallel operation and kit shall be supplied with UPS.

1 x 5 KVA UPS.

MV PANEL WITH CAPACITOR PANEL

Main LT Panel fabricated out of 1.6/2mm thick for structural members CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof with reinforcement of suitable size angle iron, channel 'T' irons and/ or flats wherever necessary, 16 gauge CRCA sheet steel shall be used for final distribution panels. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be (form-3b Construction) treated with all anticorrosive process before painting as per specifications with 2 coats of zinc chromate primer and final approved shade of enamelled paint. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system and with 15% spare space, lifting hooks shall also be provided in case of large panels.

Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels.

Breaking capacity mentioned is Ics value.

This BOQ to be read in conjunction with technical specifications and Single Line Diagram (attached for reference). If any discrepancy occurs that should be brought to the notice of Client/Consultant before quoting the price otherwise stringent condition will be deemed to have been considered.

All MCCBs shall be provided with rotary operating handle and ON/OFF lamps backed by 6Amp control MCB.

All meters shall be digital type (unless otherwise specified)

Multi-function meter to be provided as required to cover all the parameters as mentioned.

All current/voltage transformer shall be cast resin type.

All indicating lamps shall be LED type.

Current density for bus bar shall not be more than 0.8 A/Sqmm. Rating of Bus bar is after considering all derating factors. (Bus bar sizing calculation to be submitted for approval.)

All internal control wiring shall be heat resistant type.

All incoming breakers in Main LT panel shall be electrically interlocked.

Bus bar chamber shall be provided at top only. Incoming and outgoing cable entry shall be from top/bottom as required.

All feeders shall be provided with door interlocked with door defeat, pad lock facility.

Live parts shall not be accessible after opening the door, Transparent acrylic sheet to be provided to cover the same.

Spare contacts of MCCBs/ MCBs/ Relay/ Contactor shall be wired upto terminal block.

20% spare control terminal to be provided.

All MCCBs shall be provided with variable O/L & S/C releases. Incoming MCCB shall be provided with E/F releases also

All incoming/outgoing cables shall be terminated on links/terminals.

INCOMING :

1 No. Main Income 400A, 4P, MCCB (36KA) with Micrcoprossor based release for Over load, Short circuit Protection

1 No. DG Incoming 400A, 4P, MCCB (36KA) with Micrcoprossor based release for Over load, Short circuit Protection

1 No. Solar Incoming 200A, 4P, MCCB (25KA) with Thermal Magnetic release for Over load, Short circuit Protection

2 Nos. 400A, 4P, Contactor Main, DG, Solar With (AMF Relay) for DG Auto Manual Start Stop,

1 Nos. 200A, 4P, Contactor for Solar

Metering:

Phase indication lamps each backed up with 6 Amps MCB.

Three (3) Nos.Multifunction Digital meter RS 485 Port. (consisting of Voltage, Amps, kWh, kW, P.F. parameter) with Current Transformer

1 nos. Surge protection device class-B+C backed up with 160 Amps Fuse.

Under Voltage/Over Voltage Realy, Earth Leakege Relay Of Both incomer

2 set On/Offf/Trip Indication Lamp

MAIN BUS BAR

One sets of 400A,TPN AL. Bus Bar with PVC Sleeve in sealed Bus Chamber.

OUTGOINGS:

One (1) Nos. 100 A, 4P MCCB .(25KA) Thermal Magnetic Release

One (1) Nos. 63 A, TP+N, MCB .(10KA) C Curve,. For 9.3kw Star Delta Starter for Fire Fighting Systems

2 Set. Phase indication lamps each backed up with 6 Amps MCB.

2 Nos.Multifunction Digital Meter RS 485 Port. (consisting of Voltage, Amps, kWh, kW, P.F. parameter) with Current Transformer backed up with 6 Amps MCB

(15) Nos. 63 A, TPN, MCB .(10KA) C Curve With Aux. contact For On Off Indication

One (1) Nos. 32 A, TPN, MCB .(10KA) C Curve With Aux. contact For On Off Indication

One (1) Nos. 40 A, DP, MCB .(10KA) C Curve With Aux. contact For On Off Indication

One (1) Nos. 32 A, DP, MCB .(10KA) C Curve With Aux. contact For On Off Indication

75KVAR CAPACITOR INCOMER :-

1 No. Main Income 160A, TP+N, MCCB (25KA) with Thermal Magnetic Release for Over load, Short circuit Protection

BUSBAR :-

One sets of 150A,TPN AL. Bus Bar with PVC Sleeve in sealed Bus Chamber.

METERING, INDICATION AND RELAY :

1 Nos.Multifunction Digital Meter RS 485 Port. (consisting of Voltage, Amps, kWh, kW, P.F. parameter) with Current Transformer backed up with 6 Amps MCB

1 set Automatic Power Factor Correction Relay (8 Steps) with digital Power Factor Meter

One set of R/Y/B phase indication Lamp with control MCBs.

On/Off Trip Indication

1 set of Aux. Contactors

1 No. timer for manual mode switching

1 set Control MCB

OUTGOINGS:

1 Set of 1KVAR Capacitor bank 1X3Kvar Capacitor Duty Contactor and 10 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

2 Set of 2KVAR Capacitor bank 2X3Kvar Capacitor Duty Contactor and 10 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

1 Set of 5KVAR Capacitor bank 1X5Kvar Capacitor Duty Contactor and 16 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

1 Set of 10KVAR Capacitor bank 1X10Kvar Capacitor Duty Contactor and 25 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

2 Set of 15KVAR Capacitor bank 1X15Kvar Capacitor Duty Contactor and 32 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

1 Set of 25KVAR Capacitor bank 1X25Kvar Capacitor Duty Contactor and 63 A TP MCB (10kA) Capacitor rating to be designed for required output KVAR at 415V.

Main LT Panel With Capacitor Bank described above.

HVAC PANEL

INCOMER :-

One (1) Nos. 100 A, 4P MCCB .(25KA) Thermal Magnetic Release

1 Set. Phase indication lamps each backed up with 6 Amps MCB.

1 Nos.Multifunction Digital Meter RS 485 Port. (consisting of Voltage, Amps, kWh, kW, P.F. parameter) with Current Transformer backed up with 6 Amps MCB

BUSBAR :-

One sets of 150A,TPN AL. Bus Bar with PVC Sleeve in sealed Bus Chamber.

(5) Nos. 63 A, TPN, MCB .(10KA) C Curve With Aux. contact For On Off Indication

HVAC PANEL

UPS PANEL WITH BY PASS ENCLOSER

INCOMING :

1 No. Main Income 32A, DP, MCB (10KA) C Curve'

BUS BAR :

One set of 32 A TPN Copper Strip Bus Bar, 25kA with PVC Sleeve in sealed Powder Coated Bus Chamberas approved by architect and complete in all respect.

METERING AND INDICATION :

1 Nos.Multifunction Digital Meter RS 485 Port. (consisting of Voltage, Amps, kWh, kW, P.F. parameter) with Current Transformer backed up with 6 Amps MCB

One set of R/Y/B phase indication Lamp with control MCBs.

OUTGOING :

3 Nos. 10A DP MCB C Curve' (10KA)

1 Nos. 16A DP MCB C Curve' (10KA)

2 Nos. 32A, DP, MCB (10KA) C Curve' With Ms Encloser for UPS By Pass.

Ups Panel With Bypass Encloser described above.

TOTAL OF MV PANELS

POINT WIRING & ACCESSORIES

COPPER WIRING WITH MODULAR SWITCHES IN MS CONDUITS (SURFACE/RECESS)

Wiring for Light/Fan/call bell point with modular type switch/socket and GI box, Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in 1.6 mm think MS conduit

Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit,and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit asrequired.

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 4 sq. mm earth wire

4 X 6 sq. mm + 2 X 4 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.

Conduit of 25 mm dia.

Conduit of 32 mm dia.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required..

Conduit of 20 mm dia.

Conduit of 25 mm dia.

Conduit of 32 mm dia.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

TOTAL OF POINT WIRING & ACCESSORIES C/O TO SUMMARY

MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc.

MCB DISTRIBUTION BOARDS

Supply and erection of double door sheet steel enclosure distribution board suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all labour and material required to complete the job in all respect up to to the entire satisfaction of the Engineer-in-Charge of the work.

SPN DB Double Door 8 way

SPN DB Double Door 12 way

TPN DB Horizontal type Double Door 4 way

TPN DB Horizontal type Double Door 6 way

TPN DB Horizontal type Double Door 8 way

Supply and erection of miniature circuit Breaker/isolator 240/415 V in the existing distribution board including making necessary connections:-

6 amp. to 32 amp Single Pole

40 amp to 63 amp. Double pole

40 amp to 63 amp. MCB's Three Pole

Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures including making necessary connections and bonding to earth with all labour and material required to complete the job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.

DP RCCB 30ma sensitivity , 40 A

DP RCCB 30ma sensitivity , 63 A

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from theceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.

MS perforated cable tray painted with powder coating 150 X 50 X 1.6 mm

MS perforated cable tray painted with powder coating 250 X 50 X 1.6 mm

MS perforated cable tray painted with powder coating 300 X 50 X 2 mm

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

2 pair telephone wire

4 pair telephone wire

Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing surface/recess MS/PVc conduit as required

2 run of cable

1 run of cable

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

5/6 A switch

15/16 A switch

3 pin 5/6 A socket outlet

6 pin 15/16 A socket outlet

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing of modular Blanking plate on the existing modular plate & switch box including connections but excluding modular plate etc. as reqd

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75mmX75mm)

3 Module (100mmX75mm)

4 Module (125mmX75mm)

6 Module (200mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required.

Supplying and fixing brass batten/ angle holder including connection etc. as required.

TOTAL OF MCCB ,DISTRIBUTION BOARDS, MCB's, RCCB's, CHANGE OVER etc C/O TO SUMMARY

HT,LT CABLE & EARTHING

EARTHING

Earthing with G.I. earth pipe 4.5 mtr long, 40 mm dia including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required

Earthing with G.I. earth plate 600mm x 600mm x 6mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600mm x 600mm x 3mm thick including accessories and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal / coke and salt as required.

Providing and fixing earth bus of 25 mm X 5 mm GI strip on surface for connections etc. as required.

Providing and fixing 50 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 50 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Parallel Connectors for (700mm air terminal) connecting two conductors in parallel manner. Material- StSt, with clamping range- Rd / Rd 7-10 mm & Complied as per Standard EN 62561-1.

Air-termination rod having length- 2000 mm, of Material- AlMgSi, of Diameter Ø 16 mm, & Complied as per Standard EN 62561-2.

Side Wall Clamp for air terminal,

Air-termination rod clamps for connecting air-termination rods with one or two conductors. Material of clamp Al, with clamping range of air-termination rod 16 mm and Clamping range of conductor Rd 2x 8-10 mm, & Complied as per Standard EN 62561-1.

Universal connector of Material- StSt, with clamping range- 8-10mm, with truss head screw M10x35 mm & Complied as per Standard EN 62561-1.,

Roof Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN 62561-2.,

Conductor holder for Parapet wall/Side wall. Having height- 16 mm, Thread of conductor holder- M8, Material of conductor holder- SS, Conductor leading- loose, Conductor holder support Rd- 8 mm. With accessories Screw and Gitty, Material SS (M5 x 50mm)

Roof conductor holder FB2 for flat roofs with concrete block-C35/45 with double conductor holder- Rd 8 mm fixed, Dimension- 141 x 86 x 70 mm

Down conductor

Down Conductor of Diameter Ø- 8 mm, Cross-section- 50 mm2, of Material- AlMgSi & Complied as per Standard EN 62561-2.,

Conductor holder for Parapet wall/Side wall. Having height- 16 mm, Thread of conductor holder- M8, Material of conductor holder- SS, Conductor leading- loose, Conductor holder support Rd- 8 mm With accessories Screw and Gitty, Material SS (M5 x 50mm)

UNI Disconnecting Clamps with intermediate plate for round and flat conductor of Material- StSt, Material thickness- 2.5 mm, with clamping range- Rd / Fl 8-10 / 30 mm, & Complied as per Standard EN 62561-1.,

HT CABLES

33 KV Cable

Laying of one number additional XLPE power cable of 33 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Above 120 sq. mm and upto 400 sq. mm

Laying of one number XLPE power cable of 33 KV grade of following size in the existing RCC/ HUME/ METAL pipe as required.

Above 120 sq. mm and upto 400 sq. mm

Supply of HT Cable

Supplying of 33 KV grade aluminium conductor, cross linked polyethylene (XLPE) insulated individual core screened, flat steel/strip armoured PVC sheathed cable complete as required.

3 C x 185 Sq.mm, XLPE HT cable (Earthed)

HT Cable Termination

supplying and making indoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required :

Supplying and making outdoor cable end termination with heat shrinkable jointing kit complete with all accessories including lugs suitable for following size of 3 core, XLPE aluminium conductor cable of 33 KV grade as required

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting,jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

120 mm dia (OD-120 mm & ID-103 mm nominal)

160 mm dia (OD-160 mm & ID-135 mm nominal)

200 mm dia (OD-200 mm & ID-175 mm nominal)

Main Hole 1200x900

Main Hole 900x800

LT CABLE

Supply, loading, transportation unloading at site, storages at site, shifting from storage place to site of following sizes of XLPE insulated PVC sheathed, FRLS, Aluminium/Copper conductor armoured power cable of 1.1 KV grade conforming to IS amended upto date and as per specifications.

3.5C x 300 Sq.mm

3.5C x 240 Sq.mm

3.5 C x 185 Sq.mm

3.5 C x 120 Sq.mm

3.5 C x 95 Sq.mm

3.5 C x 70 Sq.mm

3.5 C x 50 Sq.mm

3.5 C x 35 Sq.mm

4C X 25 Sq.mm

Copper conductor:-

4C X 16 Sq.mm PVC insulated copper conductor armoured control cables

4C X 10 Sq.mm PVC insulated copper conductor armoured control cables

4C X 6 Sq.mm PVC insulated copper conductor armoured control cables

4 core 2.5 Sq.mm PVC insulated copper conductor armoured control cables

Laying of one number additional PVC insulated and PVC sheathed I XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning, protective covering and refilling the trench etc as reauired.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Laying of one number additional PVC insulated and PVC sheathed I XLPE power cable of 1.1 KV grade of following size direct in ground in the same trench in one tier horizontal formation including excavation and refilling the trench etc as required, but excluding sand cushioning and protective covering.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 kV grade as required.

3½ X 35 sq. mm (32mm)

3½ X 50 sq. mm (35 mm)

3½ X 70 sq. mm (38mm)

3½ X 95 sq. mm (45 mm)

3½ X 120 sq. mm (45 mm)

3½ X 185 sq. mm (57mm)

3½ X 240 sq. mm (62mm)

3½ X 300 sq. mm (70 mm)

4 X 10 sq. mm (25 mm)

4 X 16 sq. mm (28mm)

4 X 25 sq. mm (28mm)

HT,LT CABLE & EARTHING

LIGHT FIXTURE AND FAN

22 W LED TUBE LIGHT

22 W LED TUBE UPS

10 W SURFACE LED

15 W MIRROR LIGHTS

SUPPLY OF CEILING/PROPELLER TYPE EXHAUST FANS (WITH GRAVITY LOUVERS) / CABIN FAN.

200 mm dia 960 RPM exhaust fan

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15 mm dia, heavy gauge including painting etc. as required. (Note : More than 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall be ignored)

TOTAL OF LIGHT FIXTURE AND FAN C/O TO SUMMARY

FIRE ALARM SYSTEM SYSTEM :-

Supplying, installation, testing & commissioning conventional fire alarm panel suitable 4 Zones, complete with visual indications for short circuit fault, open circuit fault, fire condition and all other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete with all connections, interconnections as required..

Supply, installation, testing and commissioning of Hooter Cum Strobe with all required accessories for mounting complete as required.

Supply,Installation,Testing & Commissioning of Analogue Addressable Control Module shall be with the facility of hard addressing, capable of providing DPDTcontact rated at 24v DC, 2A.Complete as required as per technical specification.(For hooter)

Supply, installation, testing and commissioning of Manual Call Point complete as required.

Supplying & laying of 2X1.5 sqmm fire alarm un armoured cable, 600/1000V rated with annealed copper conductor in PVC conduit complete as required.

Supplying and fixing 25 mm dia MS flexible pipe with PVC coating conduit along with all ancillaries and accessories like coupler etc. as required

LAN SYSTEM

Supply, Installation, Testing & Commissioning of L3 managed switch 24 10/100/1000BASE-T ports + 2 10GBASE-T ports + 4 10G SFP+ ports, L2 Stackable Managed Switch

SITC of CAT6A UTP 26 AWG Patch Cord - 2 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like Smoke density: Series IEC 61034 / IEC 61034-2, EN 61034-2, IEC 60754/IEC 60754-2, EN 60754-2, IEC 60332-1/60332-1-2, UL VW-1 with tensile strength >50N, Number of Insertion upto 2500 Duty Cycle (Make : Systimax/Panduit/Siemon/Legrand)

Supply of Wall Mount, assembled, UL Certified rack (RAL 7035 in Pastal fine texture OR RAL 9005 in Black fine texture) with Sheet steel riveted metal frame, Top and bottom cover with brush cable entries, confirming to following standards - IEC 60529 EN 60529 (IP20), IEC 62262 EN 62262 (IK08), DIN 41494, EIA 310, IEC 60297, Rack including accessories like Horizontal PDU, Metal Cable manager, Hardware packet and Cantilever Shelf should be from same OEM 15U (600*500mmD) with Std Acc( Make:Valrack/Legrand/APC/Rittal/Emerson)

Supply, Installation, testing and commissioning of Cat6A Tool less Information outlet for Data & Voice. Cat6 U/UTP RJ45 socket with built in crimping mechanism with capability of retermination without refreshing the wires. Toolless RJ45 Information outlet with insertion cycle (in & out) upto 2500 times (I/O) along with front side Label holder and transparent shutter. The Information Outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3bt standard for POE++ application (Make : Systimax/Panduit/Siemon/Legrand).

Supply, Installation, Testing & Commissioning of SFP+ 10GBASE-SR 10 Gigabit Ethernet Optics, 850 nm for up to 300 m

Supply, Installation, testing and commissioning of Single Mode OS1/OS2 SC-SC Duplex Fiber Patch Cord LC-LC - 3 mtrs. Conform to IEC 61754-4,61300-3-4,61300-3-34,61300-3-6,61300-2-1/2/4/5 EIA-TIA, G.657.A2 and Telecordia performances requirements (Make : Systimax/Panduit/Siemon/Legrand)

TOTAL OF LOCAL AREA NETWORK C/O TO SUMMARY

SMART PLUS IP CCTV SURVEILLANCE SOLUTION

Supply, Installation, Testing & Commissioning of 2MP IP Network TDN Low-Light IR Rugged Bullet Camera, 1/2.8" CMOS or better, 2MP (1920 x 1080) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.005 lux @ F1.6 (color), 0 Lux IR On, 4 IR LEDs Smart IR with upto 60m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio 50db, Shutter Speed 1/8 - 1/30,000; Adavance Video Compression technology such as H.265 & H.264 High Profile & MJPEG , Triple stream, 2.7 to 13.5mm 5X motorized focus & zoom lens, Field of View FoV H:80°-24°, BLC, HLC, 3DNR White Balance, Minimum Edge Intelligence Video Analytics : Video Motion Detection, Tampering, Loitering, Intrusion, & People Counting, 4 Privacy Mask, 8 Region Of Intreset, Defog, TLS1.2, AES-128/256, SSH/Telnet closed, Stream Encryption, Dual channel Audio, Alarm: 1In/ 1out, 256GB SD card support, PoE (802.3 af) and 12V DC, Max 6W, IP 67, IK 10 vandal proof with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF Profile S/G/T compliant, UL/CSA 62368-1, CE (EN 50130-4), FCC Part 15, EN 55032, RoHS (EN63000) & NDAA Section 889 compliant.

Supply, Installation, Testing & Commissioning of Network Video Recording Software (NVR) to support min 128 Cameras with 2MP Resolution, 25fps and stores Video for 30 days in 2MP, 25fps in RAID5/6. NVR shall support UHD, 4K, Full HD resolution, H.265 compression codec, multi-imager/lens cameras and 360° fisheye cameras. The NVR shall support in N+1/N+M failover features so that more failover can be added if required. NVR shall be licenced for 128 cameras & 03 users clients. The NVR should support network joystick controller, GPU rendering support for H.264 and H.265 decoding , video on demand, Adaptive video throttling, rule engine, operatore role management, server based Video Motion Detection (VMD), edge storage backfill support, bookmark with manual comment, bookmark based search, timeline search, Preview search, synchronous playback, monitor wall support, surrounding camera mode, Cybersecured with features such as Digital Signing, General Data Protection Regulation (GDPR) compliance, HTTPS & SSL base, smart web client, secured firewall configuration, password expiry, non-recoverable password; support ANDROID & iOS phones, seamless integration with intgegrated Access Control System. NVR software Shall be listed on ONVIF website for ONVIF S, G & T support compliance. Approved Makes ( Axis/Avigilon/ Bosch/ Honeywell Enterprise)

Supply,installation, testing & commissioning of 8 TB Survilieance Hard Disk for storrage complte as required. Make- Seagate/ WD

Supply, installation, testing & commissioning of 42" Flat LED Color Monitors.Make Sansung/LG/ Panasonic

Supply,installation, testing & commissioning of; 10/100/1000 POE L2 Ethernet Switch 16 port with 2 Nos of Fibre Slot and as per specification complete as required.

Supply,installation, testing & commissioning of; '6U Network Rack (wall mounted)

Supply, installation, testing and commissioning of CAT-6 unarmoured Data cable including all necessary accessories.( Switch to camera) in existing PVC Conduit.

Supply,installation, testing & commissioning of 3C X 1.5 sq. mm power supply cable.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20mm PVC Conduit

25mm PVC Conduit

TOTAL OF SMART PLUS IP CCTV SURVEILLANCE SOLUTION C/O TO SUMMARY

SOLAR SYSTEM

Grid-connectsystem

SolarPVSystemSize–100 kWp

HighqualitySolarPanelsmountedatatilt of 5 degree&18 degree horizontal

HighefficiencyStringInverter;Uvprotectedtincoatedcopperwires

LonglifeStructureswithgalvanizationcoatingtopreventrustingand designedtowithstandwindspeedof>150km/hour

AsBasedonyourstatenetmeteringpolicy,spaceavailability,andtechnical parameters,werecommendyoutohaveasystemof 100 kWponyourroof.

AsperyourspecificdemandofOn-gridsystem,youcangowithanOn-grid systemof 100 kWp as approved by architect and complete in all respect..

A) Solar Module

SolarPhotovoltaic Monoperc crystalline Module-530Wp - 545Wp,144cells as approved by architect and complete in all respect.(adani/vikram/waree/renewsys)

B) String DC Couplers

Module Connector (MC4 Compatible) Male & Female pairs(almex)

C) DC CABLES

1 Core 64Sqmm Cu XLPE Solar Grade Cableas approved by architect and complete in all respect.(polycab,kei)

D) Solar String Invertor

Invertor as approved by architect and complete in all respect. (sungrow/solis/ksolaire)

E) Monitoring & Instrumentation

F) AC Distribution Box

4IN 1OUT ACDB with following: (Metal Body) - I/C-4Nos(4P,125Amp,415VMCCB) - O/G-1Nos(4P,500Amp,415VMCCB) -Multifunction display -CT Ratio -500/5A - TNP busBar - IP 65 outdoor Enclosure CRC PowderCoated With lockableCagewithstand -3 Nos Indication LAMP (R,Y,B) 5IN 1OUT ACDB with following: (Metal Body) - I/C-5Nos(4P,125Amp,415VMCCB) - O/G-1Nos(4P,600Amp,415VMCCB) -Multifunction display -CT Ratio -600/5A All as approved by architect and complete in all respect.

IP65outdoorEnclosureCRCPowderCoatedWith lockableCagewithstand - TNP busBar -3 Nos Indication LAMP (R,Y,B) All as approved by architect and complete in all respect.

21IN1OUTACDB withfollowing:(MetalBody)-O/G-1Nos (4P,2000Amp,415VACB) -Multifunction display -CT Ratio -2000/5A - IP 65 outdoor Enclosure CRC PowderCoated With lockableCagewithstand - TNPbusBar-3NosIndicationLAMP(R,Y,B) All as approved by architect and complete in all respect.

Solar Meter as approved by architect and complete in all respect.

G) AC Cables

1.1 kV 25 Sq.mm 4 Core Cu. arm XLPE Cable

1.1 kV 400 Sq.mm 3.5 Core AL. arm XLPE Cable

33 kV 300 Sq.mm 3Core AL. arm XLPE Cable

1.1 kV 4 Sq.mm 1 CoreCu. XLPE Green Cable (Module Earthing )

1.1kV70Sq.mm1Core Cu. XLPE Green Cable (ForLA)

H) Miscellaneous Items

Underground Trench With RCC

MS Rack for AC cable Laying on wall

DWC HDPE Conduit 32/26mm( With all accessories to complete the work) or cable tray

ESE Type LA ( R-107 Meter With earthing pit ) With Accessories

Cableties(Nylon,66UL94V-2,300mm)withUVStabilized &ferrules

Maintenance Free Earth Electrode (3 mtr long,dia of17.2 mm dia,Copper Bonded, thickness of 250 microns, with Carbon based grounden hancing material with suitable I Clamp,Heavy duty Poly propelyne Circular earth pit Chamber as approved by architect and complete in all respect.

GI Earthing Strips 25x3mm

I) Structures

GI Structure With 80 micron as approved by architect and complete in all respect.

Civil Foundation (RCC) as approved by architect and complete in all respect.

J) Services

Installation and Commissioning as approved by architect and complete in all respect.

Cost of the Solar Panel (100kWp)

Total Cost of the Solar Panel

TOTAL OF SOLAR SYSTEM C/O TO SYMMARY

Supply, installation, testing & commissioning of 13 Passenger Lift for G+6 RCC Framed structure of standard dimension & speed including all allied civil, electrical, mechnical fittings & fixtures as per the direction of Engineer-in-charge

Split Units AC

Hi Wall Split Units

Supplying, fixing, testing and commissioning of Hi Wall type split air-conditioning unit suitable to operate from 230±10% volt, 50 Hz, 1 phase power supply, with air-cooled evaporator with coil, fan,drain pump, and fan motor, air-cooled condenser with hermetically sealed rotery / reciprocating compressor condenser coil, propeller fans controls, control panel, Including control wiring, necessary power cable, M.S. frame duly painted to locate Outdoor Unit etc. The Unit should be atleast 3 Star rated. The Refrigerant pipe size and gas quantity should suit to the cupper pipe length at actual.(total circuit including liquid & suction) with interconnecting cabling between indoor / outdoor units as per site incharge, 13 mm thick.

2.0 TR (SUPERINTENDENT ROOM) (hi-wall)

Supply , Installation, Testing & Commissioning of HVAC Works

PART - A HIGH SIDE

VRV Outdoor Units cooling only top discharge

Supply Installation, Testing and Commissioning of Modular Type Out Door Units equipped with modular type high efficiency all inverter technology based hermetically sealed scroll compressors suitable for R410A refrigerant, suitable for operation on 400±5% volts, special heat exchanger with al. fin and copper tube, Centrifugal fan for condenser, electrical and microprocessor base panel and all accessories for proper functioning the unit .Make - LG/DAIKIN./BLUESTAR

The Outdoor and Indoor Unit shall be integrated with special super wiring system with centralised remote control system into one common wiring.

ODU having auto check function for correction eroor, auto addressing system, oil return system, soft starters for compressor motors, under voltage/over voltage trip, single phase preventers, communication card etc.

Unit price shall be inclusive of Refrigerant Gas for full system, MS structure and RCC/PCC Foundation required etc. to complete the system as required as follows:-

36 HP ( Cooling only top discharge ) ------------ 1 Nos

VRV Indoor Units:

Supply Installation, testing and commissioning of Indoor Units suitable for operation on 220 - 240V, 50 Hz, single phase AC supply complete with cooling coil, electronic expansion valve, multi speed fan motors, dynamically balanced blowers, built in drain pump, synthetic washable plasma media filter including insulation with Cordred /cordless remote control oeration capable of varying the air flow automatically as per inside load condition with inverter technology complete as required. Make - LG/DAIKIN./BLUESTAR

ROUNDFLOW WITH WIRELESS REMORT

3.3 TR - 4 Nos

4.12 TR - 03 Nos

4.65 TR - 01 Nos

Refnet

Supply, installation, testing and commissioning of copper Refnet factory febricated along with suitable insulation as per shape of the refnet as required to connect the above VRV/VRF indoor and outdoor units. Make - LG/DAIKIN./BLUESTAR ------------ 09 Nos

Remort

Cordless ------------------------- 08 Nos

PART - B LOW SIDE

Installation, testing and commissioning of VRV ODU unit

36 HP------------------------- 01 Nos

Installation, testing and commissioning of VRV Indoor unit

ROUNDFLOW WITH WIRELESS REMORT

3.3 TR ------------------------- 04Nos

4.12 TR ------------------------- 03 Nos

4.65 TR ------------------------- 01 Nos

Refnet

Installation, testing and commissioning of copper Refnet ------------------------- 09 Nos

Remort

Cordless remort ------------------------- 08 Nos

Refrigerant Piping

Supply, installation, testing and commissioning of interconnecting high pressure copper refrigerant piping work suitable for refrigerant R410 duly insulated with class-O, elastomeric nitrile rubber type tubular insulation of density 40 ~60kg/m3 between indoor & out door units. Piping inside occupied area and vertical shaft shall de supported using GI Hangers. The 19mm thick insulation shall be considered. Copper pipe Make - RAJCO/DAIKIN,/ Maxflow / Mandeep Insulation Make - K-FLEX / A-FLEX. /Aermocell

Liquid and suction gas line with insulation ------------------------- 82 Rmt.

Communication and Transmission Cable

Supply,installation,testing and commissioning of 2C x 1.5 sqmm copper conducter flexible cable laying in PVCcunduit with bent, tee as require for communication beetween VRV IDU and ODU and also for Central remote controlling system. Make - RR /Finolex /Havells /KEI / Polycarb. ------------------------- 140 Rmt.

Refgirent gas

R410 MAKE - Floron ------------------------- 13.68 KG

Nitrogen Pressure Check

500 PSI Nitrogen pressure hold for leak check and 500 microns vacuum. -------- 1 Lot

Drain Piping

Supply,installation,testing and commissioning of CPVC drain pipes density 20Kg/m3 complete with fittigs like elbows, tees, reducers, bends, flanges, supports with 6 mm thick class - O nitrile rubber insulatiions complete with supports as per drawings and specifications of below sizes make - as per ability.

25 mm dia ------------------------- 24 Rmt.

32 mm dia ------------------------- 24 Rmt.

ODU LIFTING & SHIFTING

ODU lifting ,shifting and placement ------------------------- 02 Nos

M/S ODU STAND

SITC of ODU stand & vibration control, rubber pad , with nut, bolt, owaser , fastenurs etc complete with all accossories. ------------------------- 02 Nos

TOTALHVAC WORKS AMOUNT

TRIBENI CONSTRUCTIONS LIMITED (BID ID -751416)

Badri Rai and Company (BID ID -751310)

Delhi Engineers Construction Company (BID ID -750731)

JCICL (BID ID -751471)