Special repair of VIP Lounge at Air Strip Bachhod (Narnaul) in Mohindergarh District.

Amount

Scraping white wash and colour wash. (HSR 8.32) (a)

Factory manufactured panelled door or glazed windows shutters of commercial hard wood such as Hollock & Champ only. (non coniferous timber other teak, confirming to I.S. pecificationNo. 1003, Kiln seasoned) with 100mm wide vertical styles, 150mm wide lock rail 200 mm wide bottom rail, and 100mm wide other rails, with panels of 15mm thick, tongued and grooved of commercial hard wood nd including cost of iron hinges, screw, chock/cleats, stops nails etc. complete in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position). (a) 35 mm thick. [HSR 17.90 (b)

Factory manufactured wire gauze door and window shutters of commercial hard wood such as Hollock & Champ only. (non-coniferous timber other teak conforming to I.S. specification No. 1003, kiln seasoned) with 100 mm wide vertical styles, 150 mm wide lock rail 200 mm wide bottom rail, and wire gauze of 140 G or 120 G designation including cost of iron hinges, screws, chock/cleats, stops nails etc., complete fixed in position (excluding the cost of any fittings, other than specified above, but including labour for fixing the same in position. (Styles and rails of windows shutter shall be 75 mm wide. (ii) 35 mm thick. [HSR 17.92

Factory manufactured Solid Flush Door Shutter, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hotpressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position. (Make: Duro, Green). HSR 17.93 (a) (iii) 35mm thick

Supplying and fixing Glass panes including special metal sash putty of approved make. (b) glass panes 4 mm thic, exceeding 40 sq. dm areas. [HSR 18.30 (b)].

Providing and applying two coats white cement based putty over plastered surface and grindling the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc. complete. (J.K./ Birla). (HSR 16.81)

Distempering with washable oil bound distemper (of approved manufacture) two coats over one priming coat on new work. (HSR 16.58)

Providing two coats of exterior acrylic emulsion paint. (HSR 16.79) (b)

Painting two coats with synthetic enamel paint in all shades on old wood-work or metallic or plastered or concrete surfaces to give an even shade including rubbing down old paint. (HSR 16.5)

Cost of brass fittings complete for doors and windows, such as tower bolts, handles,etc, and screws for these fittings (exculding sliding bolt) (HSR 17.70) (a) for single leaf shutter

Providing and fixing false ceiling with grooves 12mm to 15mm thick 600mm x 600mm best quality complete as all respect (HSR 13.93)

Providing & fixing Wall Panneling of 1 mm. thick laminate of approved shade of any make namely Royal touch, Greenlam and Marino and make over 19mm. thick commerical plywood ISI mark with 3mm. wide groove, fixed to wall with 4" high teak wood skirting complete in all respect (as desired by Engineer-in-charge / approved drawings) at site of Work (N.S.)

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make in flooring laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1:3 and joint will be 3 mm wide instead of zero joint by using spacers to ensure uniformity of joint duly filled with epoxy grout minimum depth of 3 mm of (reputed make such as pidilite (T-13 Roff), Ferrous crete or equivalent) as approved by Engineer-in-charge. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO. (Double charged tiles shall be used as approved by Engineer in charge. (HSR-14.89). material.

Providing & Fixing Vitrified Tiles 600 x 600 mm of approved make skirting/dados, pillars, wall facing, laid in any pattern as specified over base of 20 mm thick cement coarse sand morter 1:3 and joint will be 3 mm wide instead of zero joint by using spacers to ensure uniformity of joint duly filled with epoxy grout minimum depth of 3 mm of reputed (make such as pidilite (T-13 Roff), Ferrous crete or equivalent) as approved by Engineer-in-charge. Note:- Tile shall be of premium quality (first quality) of reputed manufacturer like: RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO. (Double charged tiles shall be used as approved by Engineer in charge. (HSR-14.90).

Providing & Fixing Ist quality Ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manu-facturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-In-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 coarse and jointed with grey cement slurry, including ointing in white cement mixed with pigment of matching shades complete. (b) Size of ceramic Glazed tiles 300 x 450 mm of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. [HSR 14.92(b)].

Providing & fixing ceramic tiles/anti skid tiles of size 400mm x 400mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thickcement coarse sandmortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles. Not : Tile shall be of premium quality (first quality) of reputed manufacturer like:- RAK, NITCO, KAJARIA, SOMANI, JOHNSONS, ORIENTBELL, SIMPOLO shall be used as approved by Engineer-in-charge. (HSR 14.91). Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Laying and fixing Granite stone in all shades 15 mm to 18 mm thick in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite stone. (Excluding the cost of Granite, Granite will be supplied by the Department). (HSR 14.96).

Laying and fixing Granite stone in all shade,15mm to 18mm thick in skirting/dados, risers of steps, pillars, wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortor 1:3 and jointed with white cement slurry mixed with pigment to match the shade of granite including labour for fixing cramps pins and dowels etc. (Excluding the cost of Granite, Granite will be supplied by the Department). (HSR 14.95).

Precast chequered tiles of 20 mm thickness In ordinary grey cement without chips laid on 20 mm thick bed of cement coarse sand mortar 1:3 with neat cement slurry between joints and over the base in floors, treads of steps and landings. (Note:- Reputed make Tile Only ISI marked will be used as approved by Engineer-in-charge). [HSR 14.45+Note]. Note:- The Agency to whom the work is alloted will have to produce original bill/voucher for all quantity in token of proof of purchase of material.

Dismantling Brick Work, Tile Masonry or Tile Lining and Tile Terracing, (b) in cement (HSR 8.5 b)

Dismantling cement conglemerate / terrazzo floors 25 mm to 50 mm thick including concrete base (HSR 8.25)

Brick jali with 22.86 cm X 11.43 cm thick alternate layers laid in cement sand mortar 1:4 using 58 numbers bricks. (HSR 11.71)

First class brick work laid in cement sand mortar 1:4 in foundation plinth. (HSR 11.4)

Cement Concrete 1:2:4 gola 10cm x 10cm quadrant along junction of roof with parapet wall finished smooth, where specified. (HSR 13.64).

Cement Concrete 1:2:4 with stone aggregate 20 mm nominal size in foundation and plinth. (HSR 10.41).

Providing and Fixing HDPE WATER STORAGE TANKS of Sintex, Diplast, O.K. Supreme make with covers/lids marked with IS:12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow and scour provisions with suitable plug on scour pipe including cost of nipples, washers flages for connections in tanks complete in all respects to the satisfaction to the Engineer-in-Charge. [HSR 30.119]. 1000 Ltrs. Capacity Water Tank

Extra for fixing & jointing union couplings in G I on W I pipe line (HSR 28.21) 15mm

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside building including cartage from divisional stores or nearest railway station to site of works. (HSR 28.29) 15mm internal diameter

20mm internal diameter

Construction brick masonray inspection chamber sizes as given below upto 0.60 metres average depth in cement mortar 1:5 lime concrete with 40 percent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plastern 1:2 with a floating coat of 1 mm thick of neat cement RCC 1:2:4 slab 100mm thick/C.C. topping 50mm thick with 455 mm x 455 mm / 455 mm x 610mm inside light duty C.I inspection chamber cover and frame weight as per I.S.I specification painted with 3 coats of black bitumastic superior paint complete as per standard design.a) Size inside (with 455mmx455mm cover and frame light duty single seal weighing 20 kg with C.C topping. (HSR 29.84) 600 mm x 900 mm

Providing and fixing in position best Indian make European type water closet suite with concealed 'P' or 'S' trap with or without vent (as approved by the Engineer-in-charge) and all other necessary fitting as fully described in item no 30.3 above (HSR 30.6) i) White

Extra over item no. 30.1 to 30.4 and 30.6 for providing and fixing 15 litres capacity low level vitreous china ware cistern complete with flush bend all other necessary fitting instead of C.I high level cistern complete with fitting. (HSR 30.12) (i) white

Extra over item no. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid (HSR 30.13)

Extra for providing and fixing 32mm dia G.I/C.P flush pipe complete with acessories insread of 32mm dia glavnised telescopic flush pipe with clips (as required by Engineer-in-charge) (HSR 30.15) a) 32mm dia G.I flush pipe

Providing and fixing in position best indian make Lavatory suites (With full anti splash rim in vitreous china ware and all other necessary fittings as fully described in item no 30.41 above (HSR 30.42) 530mm x 430mm with one no. tap

Providing and fixing in position best Indian make shower with 15 or 20 I/D in-let (HSR 30.66) C) CP Brass with revolving joint

Providing and fixing in position best indian make towel rails fixed in with rawlslugs embedded in walls with C.P Brass screws, complete in all respect including cutting and making goods the walls etc. (As per item no 30.41) (HSR 30.68) (a) (ii) 2mm dia, CP Brass Adjustable (a) 600mm long

Providing and fixing in position best Indian make bevelled edge 5.5mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embeded in the wall or chromium plated brass clamps with C.P. brass screws (as required by the Engineer -in -charge) complete including cutting and making good the walls etc. (a) Indian make (As per item no 30.41) (HSR 30.71) (i) 600mm x 450mm

Providing and fixing in position 15 mm I/d C.P. brass bib cocks of best quality (as required by the engineer I charge) (HSR 30.75) (a) Bib cock long body

(b) Bib cock

Providing and fixing in position C.P brass stop cocks (as approved by the Engineer-in-Charge) (HSR 30.76) a) 15mm stop cock i) Stop cock male and female end.

ii) Concealed stop cock with flange

Providing and fixing in position best indian make elexible tube connection (HSR 30.82) b) C.P brass i) 15mmx300mm.

Supply of G.I. (Medium class "B" type of Tata & Jindal make) pipe lines Make:- UNIK, TATA, ZOLOTO. (NS) G.I. Pipes 15mm I/d

Supply of G.I. Union Couplings of approved make UNIK, TATA, ZOLOTO. (NS) G.I. Union 15mm I/d

G.I. Union 20mm I/d

Providing and fixing in position best quality Stainless Steel Sinks with Complete fittings as fully described in item No. 30.51. (a) 600 mm x 450 mm x 200 mm. [HSR 30.53 (a)].

Providing & Fixing Aluminium work for door window, ventilators and partitions with extuded built up dtandard tubular Section (HSR 17.96)

Providing and fixing 12mm thick preminated particle board of flat pressed three layer (HSR 17.97) (b) pre laminated partice board with decroative lamination on both sides.

sahil

The Laxmi Co Op Multipurpose Society Ltd.

The New Bala Ji Coop L&C Society Ltd.