REPAIR MAINT MOTOR AND PUMP SETS OF WATER SUPPLY INSTALLATION AND MAINT OF CHLORINE PLANTS AND OTHER MISC WORKS AT WATER SUPPLY INSTALLATION AND REPAIR MAINT OF CI DI PIPE LINES SLUICE VALVES AT DOMESTIC AND TECH AREA AT AF STN SURATGARH

Amount

BOQ (REPAIR/MAINT /MOTOR AND PUMP SETS OF WATER SUPPLY INSTALLATION AND MAINT OF CHLORINE PLANTS AND OTHER MISC WORKS AT WATER SUPPLY INSTALLATION AND REPAIR/MAINT OF CI DI PIPE LINES SLUICE VALVES AT DOMESTIC AND TECH AREA AT AF STN SURATGARH)

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 75 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 2 here-in-after and repair of parts as per item No 3 here-in-after including installing, commissioning and testing on full load, complete all as specified and directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.1.00 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only Centre ring.

Supply only ball bearing existing size. Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Supply coupling tyre only.

Repair to parts of pump required in Ser item No-01 above here-in-before, complete all as specified and directed.

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 20HP to 30 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 5 here-in-after and repair of parts as per item No 6 here-in-after including installing, commissioning and testing on full load, complete all as specified and directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.4.00 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing existing size. Make : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Supply coupling tyre only.

Repair to parts of pump reqired in Ser item No-04 here-in-before, complete all as specified and directed.

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Disconnecting, dismantling and taking out the defective centrifugal pump set of capacity 7.5/10 HP Motor of Make “KIRLOSKAR" from foundation by opening of coupling, foundation bolts and spray painting with one coat of existing colour paint and writing SM/MES No with white paint including replacement of parts as per Item No 8 here-in-after and repair of parts as per item No 9 here-in-after including installing, commissioning and testing on full load, complete all as specified and directed by Engineer-in-Charge. Note : Spare parts and repair of parts shall be measured and paid seperately.

Supply only spare parts as under required in Srl item No.7 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only CI Impeller

Supply only CI Gland plate.

Supply only Centre ring.

Supply only ball bearing (existing size) : NBC/ SKF/ ABL

Supply only pump motor coupling assembly with tyre.

Supply bearing bowl with ball bearing plate.

Supply coupling tyre only.

Repair to parts of pump required in Ser item No-07 here-in-before, complete all as specified and directetd.

Remetalling, Turning and grinding to pump shaft.

Repairing to bearing housing.

Repair to impeller seat.

Cutting to impeller shaft key way and fixing of lock nut.

Repair to motor cooling fan shaft.

Note : Any other small items required to make functional, such as nut bolts, washers, gaskets etc are deemed to be included in item rate.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 3 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:-(a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 5 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:- (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 7.5 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:- (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 10 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:- (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 20 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:-(a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 25 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:- (a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 30 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:-(a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Disconnecting & dismantling the defective single phase/Three phase induction motor squirrel cage of any make and of capacity up to 75 HP 415 Volts, 50 HZ, 2850 RPM and rewinding the motor with super enamelled copper wire of first quality of existing size/gauge and weight including replacement of all insulation materials, varnish and all other petty items required to make motor functional and re-assembling the motor including installation commissioning and testing on full load complete all as specified and directed. Note:-(a) Transportation charges from installation to contractor works shop and back after repair are included in the rates quoted against the above items. (b) Cost of nuts, bolts, washers, connection plate, grease/ lubrication to bearing bushes etc, are deemed to be included in this item. (c) Old dismantled winding wire will be contractor property for which credit has been considered under schedule of credit.

Dismantling/taking out defective submersible pump set of capacity 15 HP from bore well/open well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed.

Rewinding of defective submersible motor of 15 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as specified and directed.

Supply only spare parts as under required in Srl item No.18 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET required under item No-18 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush Fixing.

Dismantling/taking out defective submersible pump set of capacity 7.5HP from bore well/open well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed. Note : Spare parts & repairs as required will be measured and paid seperately

Rewinding of defective submersible motor of 7.5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as specified and directed.

Supply only spare parts as under required in Srl item No.22 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET reqired under item No-22 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush fixing.

Dismantling/taking out defective submersible pump set of capacity 5HP from bore well/open well for repair by means of chain pully block or other T&P, transporting to workshop opening the pump set including repair/replacement of worn out parts, oiling/greasing, lubricating the parts and reassembling, shifting back to bore well, lowering commissioning and testing on full load complete all as specified and directed. Note : Spare parts & repairs as required will be measured and paid seperately

Rewinding of defective submersible motor of 5 HP with PVC copper winding wire of existing gauge and weight including replacement of all insulation material, "O" rings and other petty items required for making motor functional complete all as directed.

Supply only spare parts as under required in Srl item No.26 here-in-before complete all as specified and directed by Engr-in-charge:-

Supply only water seal.

Supply only cable seal.

Supply only Gun metal bearing bush.

Supply only thrust bearing complete

Supply stainless steel distance sleeve.

Supply steel impeller bowl.

Supply stainless steel motor coupling with seal.

Supply packing sheet.

Supply Guide bush.

Supply cast iron stage bowl.

REPAIR TO PARTS OF SUBMERSIBLE PUMP SET reqired under item No-26 above:-

Straightening of pump shaft by re-meting welding.grinding etc.

Repair/refixing of distance pieces.

Repair to pump stage housing by seat cutting and bush Fixing.

Demolition of brick work or stone/boulder masonary built in cement mortar including all, quions, arches, pillars, etc, but excluding ashlar facings dressed stone work and precast concrete articles, complete all as specified and directed.

M&L for brickwork with subclass B bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6, complete all as specified and directed.

S & F GI column pipe medium grade ISI marked of size 80 mm bore each of three mtrs length and both end flanged including making cut mark in flanges for smooth lowering into the tubewell alongwith suitable size nuts, bolts and washers etc, in replacement of existing u/s pipes complete all as specified and directed.

S & F GI column pipe medium grade ISI marked of size 100 mm bore each of three mtrs length and both end flanged including making cut mark in flanges for smooth lowering into the tubewell alongwith suitable size nuts, bolts and washers etc, in replacement of existing u/s pipes complete all as specified and directed.

Labour for servicing of LT starter panel in pump houses for safety checking and setting of relay and removing unserviceable copper cable and rewiring of existing size of copper cable removing burned contactors,single phase preventer,stadared operating coil and over load relay and fixing,commissioning and testing contactors,single phase preventer,standard operating coil and over load relay complete all as specified and as directed. Note: 1.Contactors,single phase preventer and over load relays are paid seperately. 2.Any other items required to make functional is deemed to be included in this quoted rate.

Supply only single phase preventor suitable for 3 phase, 415 Volts including all necessary wiring.

Supply only 3 pole power contactor ML-2. 32A Including sidemounting Add-on-aux.Contact block of existing sizeMake : L&T cat no. SS90701 or equivalent.

Supply only 3 pole power contactor ML-3 40 AMP. Including sidemounting Add-on-aux.Contact block of existing size Make : L&T cat no. SS90721or equivalent.

Supply only timer or time delay relay for star delta connection of existing make as per site.

Supply only 3 pole power contactor MNX-50. Including side mounting Add-on-aux.Contact block of existing size Make : L&T cat no. CS97075 or equivalent.

Supply only 3 pole power contactor MNX-70. Including sidemounting Add-on-aux.Contact block of existing size Make : L&T cat no. CS97076 or equivalent.

Supply only stadard operating coil ML1.5 for voltage 440 Make : /L&T cat no.SS90873POOO or equivalent.

Supply only overload relay range 13-22Amp, Make: L&T cat part No.CS90207OODO or equivalent.

Supply only 3 pole power contactor HCA0020 of Havells make . 20A Including sidemounting Add-on-aux.Contact block of existing size or equivalent of other makes as per site requirement.

Supply and fix in replacement of overload relay range 28-42 amp. Make : L&T/BCH

Removing old unserviceable starter of any type and supply and fixing testing and commissioning DOL starter, AC 3 phase, 415 Volt, 50 Hz with sheet metal enclosure with wide band coil heavy duty with single phase preventer suitable for 10 HP motor including making connection with suitable size of copper cable complete all as specified and as directed. Make: L&T TYPE MU-G10H DOL HSN CODE 8536 CAT NO OF COIL VOLTAGE 360 VOLTAGE SS95974COFO OAND CAT NO. OF COIL VOLTAGE 415 V IS SS95974DOFO OR EQUIVALENT

Removing old unserviceable starter any type and supply and fixing testing and commissioning STAR DELTA STARTER, AC 3 phase, 415 Volt, 50 Hz with sheet metal enclosure with single phase preventer with wide band coil heavy duty suitable for 15 HP submersible pump including making connection with suitable size of copper cable complete all as specified and as directed. Make: L&T, Havells.

Demolition of cement concrete of any description and in any position, complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:4:8 Type D2 using 40mm graded aggregate for base foundation for all around row water storage tanks ,water supply installation complete all as specified and as directed.

Repair excluding spares of the Automatic water supply system installed at AF Stn Suratgarh including carrying out complete maintenance/serving/repairs as required of all the sub systems viz. PLC based control panels (with all the accessories), Mimic Panel, breakdown maintenance and replacement of unserviceable parts, refixing of old serviceable parts / new parts if any including the followings and all as specified and directed by Engineer-in-Charge:-

Equipments:- (i) Automation Master Panel at water supply treatment plant. (ii) Automation Slave Panel each at all OHTs. (iii) Automation Master Panel at Booster PH No. Clear Sump (iv) Automation Slave Panel for Borewell each at ATC OHT. (v) Mimic panel Notes:- (i) New parts if any shall be paid under separate items as supply only. (ii) The scope of work includes the charges required for removing, repairing, refixing, carrying out electrical termination and fixing/installing, testing, commissioning, etc and all as directed.

Servicing of Pressure Switch i.e Cleaning checking for wear and tear, checking electrical termination, testing as directed by the Engineer-In-Charge. (once every month) and Breakdown maintenance and replacement of unserviceable parts if any all as specified and directed by the Engineer-in-Charge:- Note:- (i) The scope of work includes only labour charges required for removing, repairing, refixing of serviceable old parts / new if any carrying out electrical termination and fixing/ installing, testing, commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Solenoid Valves of size 10mm/15mm i.e Cleaning checking for wear and tear, checking electrical termination, testing as directed by the Engineer-In-Charge. (once every month) and Breakdown maintenance and replacement of unserviceable parts if any all as specified and directed by the Engineer-in-Charge:- Note:- (i) The scope of work includes only labour charges required for removing, repairing, refixing of serviceable old parts / new if any carrying out electrical termination and fixing/ installing, testing, commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Motorised Butterfly Valves and connected items of Size200/ 150mm/100/80mm i/e cleaning, greasing, checking for wear and tear, checking electrical termination, testing as directed by the Engineer-In-Charge (once every one month) and Breakdown maintenance and replacement of unserviceable parts, refixing of serviceable parts / new parts if any testing, commissioning etc and all as specified and directed. Note : (i) The scope of work includes only labour charges required for removing, repairing, refixing carrying out electrical termination, and fixing/ installing, testing and commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Servicing of Magnetic switch sensor i.e. cleaning, checking for wear and tear, checking electrical termination, testing, as directed by the Engineer-In-Charge. (once every month) and Breakdown Maintenance and replacement of unserviceable parts, refixing of old serviceable parts / new parts if any testing, commissioning etc and all as specified and directed. Note : (i) The scope of work includes only labour charges required for removing, repairing, refixing carrying out electrical termination, and fixing/ installing, testing and commissioning etc. (ii) New parts if any shall be paid under separate item as supply only.

Supply only Relay - 4 C/O, 220V Make : LEONE / IDEC/L&T

Supply only Relay– 4 C/O, 240 V Make : LEONE / IDEC/L&T

Supply only Indicator lamp of Colour : Red / Yellow / Green Make : ESBEE / Telemacnique /L&T

Supply only Push Button with LED Indicator - 240V A.C. (Colour : Red / Yellow / Green) Make : ESBEE / Telemacnique / L&T

Supply only Rust Proof Maintenance free Mangentic Float Switch Sensor. Make : RDS or equivalent.

Supply only Coil for Solenoid Valve - 10mm / 15mm 230 V AC. Make : AVCON or equivalent.

Supply only Pressure Switch 0 – 10 Kg/sq.cm. Make: Indfos/Danfoss/L&T

Supply only Electric motor suitable for actuator for 200 mm dia. Butterfly valve Make : Ritetork or equivalent.

Supply only Electric motor suitable for actuator for 150 mm dia. Butterfly valve Make : Ritetork or equivalent.

Supply only Electric motor suitable for actuator for 100 mm dia. Butterfly valve Make : Ritetork or equivalent.

Supply only Electric motor suitable for actuator for 80 mm dia. Butterfly valve Make : Ritetork or equivalent.

Supply only Capacitor for Actuator suitable for80mm/ 100mm / 150mm / 200mm dia. Butterfly Valve Make : Ritetork or equivalent.

Supply only Resistor for Actuator suitable for 50mm / 80 mm/ 100mm / 150mm / Butterfly Valve Make : Ritetork or equivalent.

Supply only Limit Switch for Actuator suitable for 50 mm/80mm/ 100mm / 150 mm/200mm dia Butterfly Valve Make : Ritetork or equivalent.

Supply only 5 pair 0.5 mm dia. armoured copper cable for sensor. Make: Havells/Nicco/Plaza/Polycab

Supply only 6 Core 1.5 sq. mm PVC sheath PVC insulated copper armoured cable.Make: Havells/Nicco/Plaza/Polycab

Supply only 4 Core 1.5sq.mm. PVC sheath PVC insulated copper armoured cable. Make: Havells/Nicco/Plaza/Polycab

Supply only 2 Core 1.5sq.mm. PVC sheath PVC insulated copper armoured cable. Make: Havells/Nicco/Plaza/Polycab

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories as required:- (a) Valve size : 100 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modren compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make: MARSH(emtork)/RITETORK/ HASSEL HOFENER/ RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories as required:- (a) Valve size : 150 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modren compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make: MARSH(emtork)RITETORK/ HASSEL HOFENER/ RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Supply, installation, testing and commissioning of Motor actuated Butterfly valve with the following specifications including all accessories as required:- (a) Valve size : 200 mm bore. (b) Designed line pressure : 1- 10 Kg/ Sq.cm. (c) Operating Angle : 90 degrees. (d) Disc material : Cast iron with nylon coating. (e) Limit switches : 02 Nos for opening and closing. (f) Mounting : Splash proof. (g) Input power supply : 230 Vots, AC, 50 Hz. (h) In built wireless modren compatibility for remote communication. (j) Valve position indicator with an output of 4 – 20 mA. (k) The actuator should be capable of accepting 4-20mA of input for regulating purposes. (l) Manual operation : Hand wheel. Make:MARSH(emtork)/ RITETORK/ HASSEL HOFENER/ RECKTRONIC DEVICES & SYSTEMS or equivalent as approved by Accepting Officer

Removing old unserviceable MCCBS and supply and fixing MCCBs 100 Amp 16 KA 4 pole 415 volt complete all as specified and as directed.

Removing old unserviceable Pressure switch and supply and fixing, testing of pressure switch for 0.5 HP booster pump made in Cropmton, Range :-0.2/+7.5 bar Pe and Diffrential :0.7/4bar, contact type: SPDT complete all as specified and as directed. Make :Danfoss/equivalent approved by GE

M&L of Earthing complete with galvanized iron or steel plate earth electrode 600 mm x 600 mm x 6.00 mm thick buried directly in ground vertically in pit of depth not less than 2.25 metre below normal ground level with top edge of the earth plate at a depth not less than 1.5 metre below normal ground level surrounded from all sides with mixture of charcoal and common salt in alternate layers and electrode connected to galvanized iron strip 25 x 4mm dia as earthing lead by means of GI bolts, nuts, check nuts and washers, earth strip protected by galvanized steel pipe 40 mm bore (light grade) connected to machinery/equipment all as shown in electrical plate No. 3 of SSR-2009 Part I and including necessary excavation and earth work in any type of soil, 20mm bore light grade GI pipe for watering, funnel, wire mesh, PCC (1:3:6) type C-1 chamber, PCC (1:2:4) type B-1 reinforced with 6 mm dia MS round bars @ 15 cm c/c both ways for cover 50 mm thick and MS frame of suitable size made of angle iron 50 x 50 x 60 mm, complete all as specified and directed by Engr-in-Charge.

Removing old unserviceable carbon bushes from Furculator and supply and fixing and testing of carbon bushes with holder of existing size complete all as specifed and as directed.

Taking up CI/DI/GI water mains 80 mm dia from trenches (including all fittings), with spigot and socket ends and lead/tyton/flanged joints including burning out joints and recovering lead complete all as specified and directed.

All as per serial item No-80 here-in-before but size100 mm bore

All as per serial item No-80 here-in-before but size150 mm bore

Taking up old rusted steel water tubing and connections in trenches/road/ nallah & fixed along walls of size 20mm complete all as specified and directed

Taking up old rusted steel water tubing and connections in trenches/road/ nallah & fixed along walls of size 25mm complete all as specified and directed

Taking up old rusted steel water tubing and connections in trenches/road/ nallah & fixed along walls for size 40mm &50 mm complete all as specified and directed

Supply & lay ductile Iron pipes of 80mm bore with spigot and socketed ends, Class “K-7”, suitable for and including rubber tyton joints complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F ductile Iron pipes of 100mm bore with spigot and socketed ends, Class “K-7”, suitable for and including rubber tyton joints complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F ductile Iron pipes of 150 mm bore with spigot and socketed ends, Class “K-7”, suitable for and including rubber tyton joints complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F ductile Iron pipes of 80mm bore with flanged ends, Class “K-7”, suitable for and including flanged ends and suitable size of rubber washers etc. complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F ductile Iron pipes of 100mm bore with flanged ends, Class “K-7”, suitable for and including flanged ends and suitable size of rubber washers etc. complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F ductile Iron pipes of 150mm bore with flanged ends, Class “K-7”, suitable for and including flanged ends and suitable size of rubber washers etc. complete all as specified and directed. Note:- Earthwork and excavation required shall be measured and paid respective items.

S&F galvanised steel water tubing 20 mm bore, 'medium grade', ISI marked as per IS 1239 part-I with all fittings ISI marked including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line in trenches/road/ nallah & fixed along walls/poles including mild steel clamps, screws etc, complete all as specified and directed by Engineer-in-Charge. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F galvanised steel water tubing 25 mm bore, 'medium grade', ISI marked as per IS 1239 part-I with all fittings ISI marked including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line in trenches/road/ nallah & fixed along walls/poles including mild steel clamps, screws etc, complete all as specified and directed by Engineer-in-Charge. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F galvanised steel tubing 40 mm bore, 'medium grade', ISI marked as per IS 1239 part-I with all fittings ISI marked including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line in trenches/road/ nallah & fixed along walls/poles including mild steel clamps, screws etc, complete all as specified and directed by Engineer-in-Charge. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F galvanised steel water tubing 50 mm bore, 'medium grade', ISI marked as per IS 1239 part-I with all fittings ISI marked including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line in trenches/road/ nallah & fixed along walls/poles including mild steel clamps, screws etc, complete all as specified and directed by Engineer-in-Charge. Note:- Earthwork and excavation required shall be measured and paid under respective items.

S&F galvanised steel water tubing 80 mm bore, 'medium grade', ISI marked as per IS 1239 part-I with all fittings ISI marked including cutting, threading etc as per site requirement and drilling holes/fixing clamp set for taking branch connection from main pipe line in trenches/road/ nallah & fixed along walls/poles including mild steel clamps, screws etc, complete all as specified and directed by Engineer-in-Charge. Note:- Earthwork and excavation required shall be measured and paid under respective items.

Excavation in trenches not .exceeding 1.5 mtr wide and not exceeding 1.5 mtr in depth for foundations, laying water mains, pipes, cables, etc getting out in soft/lose soil and formaing bottom surface to required gradient complete all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layer not less than 25 cm thick each layer complete all as specified and directed.

Removing excavated material to a distance not exc 50M and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and directed.

Run lead joints for 150 mm bore cast iron spigot and socketed pipes and fittings including jointing material i.e lead & spun yarn in repairs complete all as specified and directed.

Run lead joints for 100 mm bore cast iron spigot and socketed pipes and fittings including jointing material i.e lead & spun yarn in repairs complete all as specified and directed.

Run lead joints for 80 mm bore cast iron spigot and socketed pipes and fittings including jointing material i.e lead & spun yarn in repairs complete all as specified and directed.

Supply and fixing of Gun-metal, globe or gate valves screwed down high pressure, heavy duty (ISI marked), with iron wheel head, screwed both ends for iron pipe or for unions suitable for 20 mm bore pipe, including taking down old unserviceable gate valve complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ofGun-metal, globe or gate valves screwed down high pressure, heavy duty (ISI marked), with iron wheel head, screwed both ends for iron pipe or for unions suitable for 25 mm bore pipe, including taking down old unserviceable gate valve complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of Gun-metal, globe or gate valves screwed down high pressure, heavy duty (ISI marked), with iron wheel head, screwed both ends for iron pipe or for unions suitable for 40 mm bore pipe, including taking down old unserviceable gate valve complete all as specified and directed by Engineer-in-Charge.

Supply and fixing ofGun-metal, globe or gate valves screwed down high pressure, heavy duty (ISI marked), with iron wheel head, screwed both ends for iron pipe or for unions suitable for 50 mm bore pipe, including taking down old unserviceable gate valve complete all as specified and directed by Engineer-in-Charge.

Material and labour for Cast Iron/Ductile iron fittings for spigot and socket pipes up to 150 mm bore such as bends (any type, radius and angle) tapers, any type (straight bend increasing, decreasing or double socket etc) Tee pieces, single branch ‘Y’ junction double branch, cross collars caps and plug, and "D" joint with nuts and bolts,washers etc.complete all as specified and directed by Engineer-in-Charge. Note: Earth work will be measured and paid seperately for fixing of "D" joint in unserviceable/broken line.

Material and labour for cutting of road ,cutting chases pining in making good to facing where required to edges of landing road,hard standing,etc,and cutting chases for concealed water tubing making good exc 20 cm but not exc 60 cm width and digging of excavation40 cm but not exc 1m depth in bituminous road /concrete surface and making good as existing surface by using 0.63 mm hard core as required including premixed high performance cold mix patching material ideal for instant as require high quality repairs to bituminous as well as concrete surface all as directed by Engineer in Charge

Taking up old unserviceable Air release valves and M&L for Air release valve with two air out lets confirming to IS 14845 of size 50 mm dia bore and fixing in DI/GI/CI water supply mains of size 50mm to 150 mm dia with all fittings complete all as specified and as directed

Fixing only cast iron non return valve of size 50 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron non return valve of size 50mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron non return valve of size 80 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron non return valve of size 80mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron non return valve of size 100 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron non return valve of size 100mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron non return valve of size 150 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron non return valve of size 150mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron non return valve of size 250 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron non return valve of size 250mm bore shall be issued under Schedule 'B' store.

Fixing only CI foot valve of size 250 mm dia, lift and swing, single door IS 4038. Note:- Cast iron foot valve of size 250mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron sluice valve of size 80 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron sluice valve of size 80mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron sluice valve of size 150 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron sluice valve of size 150mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron sluice valve of size 200 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron sluice valve of size 200mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron sluice valve of size 250 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron sluice valve of size 250mm bore shall be issued under Schedule 'B' store.

Fixing only cast iron sluice valve of size 100 mm bore both end flanged, long body, class PN-1.6 conforming to IS 14846-2000 (ISI marked) with iron wheel and stainless steel spindle and fly nut, bolts, washers and rubber gasket etc, fixed in replacement of existing unserviceable sluice valve, complete all as specified and directed by Engineer-in-Charge. Note:- Cast iron sluice valve of size 100mm bore shall be issued under Schedule 'B' store.

Taking out unserviceable Air release valve, Material and labour for repairing of Air release valve with two air out lets of size 50 mm dia bore and fixing in DI/GI/CI water supply mains of size 50mm to 150 mm dia with all fittings complete all as specified and as directed.

Taking out unserviceable Non return valve of 80mm size from any position,cleaning the same thoroughly and carrying out necessary repair like changing of leather,nuts, bolts,rubber packing etc with all fittings complete all as specified and as directed.

Taking out unserviceable Non return valve of 100mm size from any position,cleaning the same thoroughly and carrying out necessary repair like changing of leather,nuts, bolts,rubber packing etc with all fittings complete all as specified and as directed.

Taking out unserviceable Non return valve of 150mm size from any position,cleaning the same thoroughly and carrying out necessary repair like changing of leather,nuts, bolts,rubber packing etc with all fittings complete all as specified and as directed.

Taking out unserviceable Non return valve of 250mm size from any position,cleaning the same thoroughly and carrying out necessary repair like changing of leather,nuts, bolts,rubber packing etc with all fittings complete all as specified and as directed.

Dismantiling of cast iron work of any description and in any position complete all as specified and directed.

Supply and fixing joist channel angle or tee sections fixed independentely with out connecting plate Etc of Fe-410 W Gde E-250 quality B, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing of plain or chequered channels squre cut or notched ordinary and counter sunk forming holes with riveted ,bolted or welded attachment FE-410W-( Gde-E 250 ) quality A for using pit cover, tank cover etc, complete all as specified and directed by Engineer-in-Charge.

Preparation of old painted surface of MS/CI pipes such as rising main, distribution mains, washout and over flow pipes,MS covers of valve pit and canal drains and painting with one coat of synthetic enamel paint, as per colour code given by the deptt , complete all as specified and as directed by Engineer-in-Charge. (Note :- The rates includes for writing and marking description of pipes with white enamel paint)

Preparation of new or previously untreated surfacef MS/CI pipes such as rising main, distribution mains, washout and over flow pipes,MS covers of valve pit and canal drains and painting with two coats of synthetic enamel paint, as per colour code given by the deptt , complete all as specified and as directed by Engineer-in-Charge. (Note :- The rates includes for writing and marking description of pipes with white enamel paint)

Material and labour for rendering 10mm thick on fair faces of brick work or concrete surfaces in CM 1:4 complete all as specified and directed.

Taking up existing DI pipe line of size 80 mm and removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint (push-on-joint) and relaying the pipe line complete all as specified and as directed. Note : 1.Excavation and eathwork shall be paid separately. 2.Incase existing DI pipe line damaged during taking up the same shall be replaced with new DI pipe of existing size. Rate shall be included in quoted rate.

Taking up existing DI pipe line of size 100 mm removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint (push-on-joint) and relaying the pipe line complete all as specified and as directed. Note : 1.Excavation and eathwork shall be paid separately. 2.Incase existing DI pipe line damaged during taking up the same shall be replaced with new DI pipe of existing size. Rate shall be included in quoted rate.

Taking up existing DI pipe line of size 150 mm removing old unserviceable Tyton joint (push-on-joint) and supply , fixing and testing of Tyton joint(push-on-joint) and relaying the pipe line complete all as specified and as directed. Note : 1.Excavation and eathwork shall be paid separately. 2.Incase existing DI pipe line damaged during taking up the same shall be replaced with new DI pipe of existing size. Rate shall be included in quoted rate.

Dismantiling of pavers blocks/tiles of any description or thickness in floors aprons etc.laid dry or laid dry or pointed complete all as directed

M&L for 100mm thick PCC 1:4:8 type D2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for 25 mm thick river sand layer spread uniformly over sub base complete all as specified and directed.

Fixing only retrived machine pressed precast concrete inter locking tiles/paver block any shape and size with grey cement and no pigment including filling the joints upto full depth with fine sand complete all as specifed and directed by Engr in charge.

Taking down old unserviceable electric water pump any size and supply and fixing testing and commissioning of electric water pump (pressue pump) self priming .37 KW/0.5 HP 220 V,50HZ including making connection with suitable size of copper cable complete all as specified and as directed Make: crompton ser no.LPEC1SB050366

Supply only 80 mm dia butterfly valve suitable for motoe actuated valve.

Supply only 100 mm dia butterfly valve suitable for motoe actuated valve.

Supply only 150 mm dia butterfly valve suitable for motoe actuated valve.

Supply only 200 mm dia butterfly valve suitable for motoe actuated valve.

Contract Amount shall be derived after deducting the amount of Schedule of Credit in General Summary on serial page No 17(R) of tender documents.

MAJOR REFREGERATION AND ELECTRICALS