Work no 15 kalandi Kunj aavasye Yojana ke pravesh Dewar ki maramaat ka karya

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. DSR-2025, S.I No-15.56

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. DSR-2025, S.I No-15.30

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. DSR-2025, S.I No-15.7.4

12mm thick Cement plaster with 1:4 Cement and coarse sand including supply of all materials, labour, Tools plants etc. required for proper completion of the work. DSR-2025, S.I No-13.4.1

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 15 (M-150) in superstructure in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) above plinth level up to floor V level (Analysed Rate)

Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. DSR-2025, S.I No-13.80

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) DSR-2025, S.I No-13.46.1

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : One or more coats on old work DSR-2025, S.I No-13.99.1

Retro-ReflectiveSheeting type-IV with 4 mm thick ACM Single Side:- Providing & fixing of reflective signs with a corrosion resistant 4 mm thick with 0.4 to 0.5 mm both side aluminium skin aluminium composite panel face to be fully covered with High Intensity prismatic sheeting type IV as per IRC-67:2012 retro reflective sheeting with back frame MS angle of 35x35x5 mm. Legends, letters , numerals and borders etc.should be as per MoRTH specification 801.3.7 .The sheeting shall have a pressure - sensitive adhesive of the aggressive - tack type requiring no heat , solvent other preparation for adhesion to a smooth clean surface, in a manner recommended by the sheeting manufacturer. The ACM (Aluminium Composite Materials) shall be fixed on the Back frame MS Angle with riveting. Micro prismatic type IV Retro reflective sheeting confirming to ASTM D4956-09 shall be Pressure fixed. The Retro reflective sheeting shall be tested for a certificate of having the sheeting tested for coefficient of retro reflection, daytime colour and luminance, shrinkage, flexibility, liner removal, adhesion, impact resistance, specular gloss and fungus resistance, 3 years outdoor weathering and its having passed these tests shall be obtained from International/Government Laboratory/ Institute by the manufacturer of the sheeting and in case the certificate is obtained from international condition, it should also be obtained from Indian condition within 3 years of launching of product by the manufacture in abroad. Alternatively, a certificate conforming to ASTM Specification (D 4956-09) on artificial accelerated weathering requirements from a reputed laboratory in India can be accepted provisionally. In such a situation, the Employer/Client, if so desires, could seek for a performance guarantee which would be released after receipt of certificate meeting the requirement of three years outdoor weathering of the sheeting as per IRC 67:2012 & Proof of the same Report shall be uploaded which quoting tender. The rate shall include all materials, labour,T&P, transportation, installation and incidentals all complete as per direction of the Engineer-in-Charge [PWD SOR-2025, SI. No.22.1]