REPAIRS TO BRICK WORK, JOINERY, PAINTING, PLUMBING WORK, ROOFING, PATHWAYS, HARSTANDING, WALLS, DRAINS, FENCING, SEWAGE CLEANING AND OTHER MISC REPAIRS IN RR UNITS OF 11 SECT RR UNDER AGE (I) BHALRA

Amount

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings,dressed stonework and precast concrete articles complete all as specified and as directed by Engineer-in-Charge.

Material and labour for brick work with sub class B bricks, straight or curved on plan exc 6m mean radius built in CM1:6

Description as per Srl Item No. 2 above but except brick

Material and labour for walling of random rubble stone masonry uncoursed well bounded, bedded and solidly hearted built in CM 1:6.

Desciption as per Srl Item No. 4 above but except stone

Pre cast cement concrete 1:3:6 Type C1 using 20 mm graded aggregate as in bond stone and set in CM 1:6.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified of random rubble walling with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm lime or sand stone, complete all as specified and directed by Engineer-in-Charge.

Material and labour for raised pointing to random rubble masonry uncourded or brought upto courses in CM 1:4 including racking out joints.

Material and labour for PCC 1:2:4 type B1 (Using 20 mm graded aggr) as in coping and similar works incl necessary from work all as specified.

Supply and fixing PVC (SWR) pipe 110 mm bore single socketed in any length with rubble ring joints as in weep holes all as directed by Engineer-in-Charge.

Taking down old cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc

Material and labour for 15mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement.

Material and labour for 15 mm thick rendering on fair faces or brick work or concrete surfaces in cement mortar 1:4 surface finished even and smooth with out using extra cement.

Material and labour for 20mm thick cement plaster on stone masonry surfaces in CM 1:4 and finished even and smooth without using extra cement.

Material and labour for applying two coats of cement based paint incl preparation of new plastered surface complete all as specified.

Preparation of old decorated plastered or unplastered surfaces of walls, conices etc by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salts and treating oil and greasy spots and applying one coat of cement base paint all as specified.

Preparation of new plastered surfaces and applying two coat of oil bound distemper on new surfaces of wall complete all as specified.

Material and labour for preparing of old surfaces of wall and applying one coat of oil bound distemper all as directed by Engineer-in-Charge.

Preparation of old painted steel surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint,desigen and pattern as approved by engineer in charge complete all as specified.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) n.exc 1.5 sqm each complete all as specified.

Description all as per Srl Item No. 20 above but exceeding 1.5 sqm n exc 4 sqm each.

Taking down shutters exceeding 1 sqm but not exc 2 sqm each.

Material and labour for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete, of frame size 125 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

Material and labour for pressed steel frames for doors with one or more rebates including necessary supply and fixing lugs, hinges, lock strike plate etc. complete , of frame size 105 x 60 mm, including one shop coat of red oxide zinc chrome primer complete all as specified

Supply and fixing solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, in opening as per specifiecation and drawings.

Material and labour for cement concrete (1:3:6) type C0 using 12.5 mm graded stone aggregate as in filling in pressed steel chowkats, bed block for holdfast and the like all as specified.

Material and labour for factory made, 2nd class hard wood rail and style 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered partical board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

Supply and fixing 2nd class hard wood, glazed and skelton shutter 35mm thick open rebated and prepared to receive glass, guage, etc. (without sash bars), edges of framing palin, chamfered or rounded, fitted with cut & mitred beads for securing glass etc. sizes of members of shutters as specified in SSR 2009 Pt-I Section 8.24(b) supplied and fitted to chowkhats, all as specified.

Supply and fixing factory made solid panel PVC door shutter 30mm thick style consisting of frame made out of MS tubes for top & bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement forstyle and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the styles & rails with suitable PVC sheet beading and jointed together with solvent cement supply & fixing in the frame at site. complete all as specified.

Supply and fixing 100mm size Butt hinges,heavy weight,cold rolled mild steel and fixed in repairs.

Supply and fixing Aluminium anodized, barrel tower bolt of extruded section, 150mm long

Supply and fixing in repairs Aluminium handle, cast type, anodized, 150mm size

Supply and fixing 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed.

Supply and fixing in repairs Helical door spring of size 300 mm including welding to steel chowkhats, complete all as directed at site.

Supply and fixing of 150mm floor door stopper of aluminium alloy body and tongue,anodised,with hard drawn steel spring,fixed in floor complete all as specified.

Material and labour for preparation of wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified.

Supply and fixing box type steel windows/Ventilator (factory made) outer frame made out ERW tube 'P' section 65X45X25 mm and shutter of ERW tube 'P' section 50mmX35mmX20mm openable (double shutter) with glazed shutter on extrernal side and gauzed shutter on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 nos on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler /AC window complete all as specified and shown on drgs No CEPZTD-324/07 Sh 1/3 to 3/3 Note:- The quoted rate a shall also include (i). One shop coat of zinc chromate primer on all exposed surface and one coat of tar on the ends of steel surface in contact with bricks / concrte surface (ii) 4 nos MS steel lugs made of 20X5 mm Iron flat 200 mm long iii)10 mm Sq Bar grill/guard bar design as per drawing (iv) PCC block for embedding lugs.

Supply and fixing Galvanised mild steel wire cloth 0.50 nominal dia of wire and average width of aperture 1.18mm complete all as specified

Supply and fixing 3 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares not exceeding 0.50 Sqm in each pane complete all as specified.

Hacking out old broken glass of any thickness, size, quality or description from the wooden frames glazing with puttyor fixed with wooden beads complete all as specified.

Material and labour for preparation of steel and iron surfaces exceeding 10 cms width or girth and applying new two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified.

Supply and fixing powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and minimum thickness of powdere coating 50 micron

Supply and fixing Powder coated aluminium door shutters, aluminum section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screw etc complete all as specified

Supply and fixing powder coated anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 No.) complete all as specified.

Supply and fixing 5.50 mm thick sheet glass fixing for Aluminium doors and windows including 25 micron reflective type sun control film complete all as directed

Supply and fixing door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60kg and fixed as in repairs (aluminium die cast body)

Dismantling CGI corrugated steel sheeting any gauge thickness including Nainital or similar pattern roof coverings, complete all as specified and as directed by Engineer-in-charge.

Dismantling timber scantling 40 sq cm and over in section framed work of any description

Supply and fixing for structural steel works of Fe 410W (Gde E 250) quality A, as in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. including painted one shop coat of zinc chromate/red oxide primer paint (including preparation of surface) before fabrication as directed.

Supply and fixing 0.5mm Pre-painted galvatume aluminium Zinc coating steel GI based corrugated sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified.

Supply and fixing 0.5mm Pre-painted galvatume aluminium Zinc coating steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified.

Dismantling wall and ceiling boards (fibre, pulp, insulation , etc.) or insulation boards/ slabs/ blankets any thikness including cover fillets.

Supply and fixing 4mm thick of size 605X605 mm, pre-premiered, self embossed, Reinforced Designer Board for false ceiling Conforming to IS-14862 and ISO-8336:1993. As per specification under mention: (i)GI section frame work (POWDER COATED) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mmX19mmX0.45mm, cross 'Tee' 28.6mm (web)X 24mm flange .33mm thick powdered coated main tee 38(Web) X24mm flange 0.33mm thick. wall angle screwed fixed to brick wall/partition wall/concrete/RCC with the help of nylon sleeves and screws @ 610 mm C/C , Then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm C/C to soffits. To from grid of 610X610mm cross Tee shall be provided @ 610mm C/C in both directions. Suitable provisions shall be made for fixing the recessed/surface mounting light fittings if any, complete all as specified and directed by Engr-in-Charge.

Supply and fixing 5mm thick Prelam PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Lining,Insulated PVC Wall Lining, and Solid PVC Partitions inclusive of Solvent Cement and fixing at site complete all as specified and directed.

Supply and fixing 5mm thick PVC sheet fillet of width 35mm for wall paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing.

Material and labour for 6mm thick plywood grade BWR, type BB, fixed as in wall/ceiling, flat or sloping fixed with nails all as specified.

Material and labour for 12mm pre-laminated partical board interior grade prelaiminated one side with decorative lamination and other side white lamination fixed with screw or nails.

Supply and fixing in repair Stainless steel drapery rods of 25 mm dia complete with coloured conical end balls at both end, dia not less then 50mm and fitted with and incl MS bracket size 150mm made to shape or 75mm dia MS end wall to wall round block made to shape in male and female pieces as required at site.

Dismantling floors hearth or wall tilling including cement mortor bedding (but not backing) removing serviceble tiles to store and rubbish off the premises.

Material and labour for colored non skid ceramic tiles 7 to 8 mm thick, area of each tile exc 0.11 sqm but n exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in colored cement to match shade, pattern, laying etc of tiles, over and incl 15 mm thick screed bed or bedding layers of cement mortar 1:6 as directed at site

Material and labour for Glazed ceramic coloured tiles, (Premier quality), of size 450 x 350 x 7 mm thick on vertical surfaces such as skirting, dados and risers to steps etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surfaces including 10mm thick rendering in CM 1:4 all as specified & directed. Note : Design, shape and pattern of fixing of tiles shall be as directed by Engineer-in-Charge.

Material and labour for Vitrified ceramic tiles 10mm thick (square/rectangular) light shade polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry over 15mm thick screed bed in cement mortar 1:6 and pointed in white or coloured cement to match.

Material and labour for machine cut kota stone slab flooring 20-25mm thick over cement screed base laid 20 mm thick in cement mortar 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and roughening the exisiting surface complete all as specified and directed.

Material and labour for machine cut kota stone slab 20-25 mm thick in riser of steps, skirting, dado and pillar laid over screed 10mm thick in CM 1:3 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and roughening the existing surface complete all as specified.

Material and labour for 20mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking plat?forms and like laid over 20mm thick in cement mortar (1:4) including roughening the exisiting surface and pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite all as specified.

Dismantling water tanks of capacity exc 250 & n.exc 500 litres each.

Dismantling water tanks of capacity exc 500 & n.exc 1000 litres each.

Rotational moulded polyethlene water storage tanks (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part-I, capacity of water tank 1000 Ltr

Description all as per Srl Item No. 68 here-in-before but tank of capacity 500 litres each

Disconnecting existing tanks exc 250 & n. exc 500 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed.

Disconnecting existing tanks exc 500 & n. exc 1000 ltrs, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position complete all as specified and as directed.

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 15mm bore of pipe.

Supply and fixing tubes, 'Medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor , 15mm bore of pipe.

Description all as per Srl Item No. 73 here-in-before but fixing only (15mm bore of pipe)

Taking up or down steel tubing and connections, including cleaning for re-fixing or removal to store 20mm bore of pipe.

Supply and fixing tubes, 'Medium grade, galvanised, with all fittings and fixed in short lengths complete to walls and ceilings or laid in floor, 20mm bore of pipe.

Description all as per Srl Item No. 76 here-in-before but fixing only.

Supply and fixing in repair bib taps, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe of bore 15mm for brass ferrule.

Supply and fixing in repair stop / angle valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe of 15 mm bore or for union.

Supply and fixing in repair 20 mm bore stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe 20 mm bore or for union.

Supply and fixing in repairs pillar tap fancy type, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered "Hot' or 'Cold' with long screwed shanks and flynuts, screwed for iron pipe 15mm bore.

Supply and fixing for PVC connections 15mm size with PTMT nuts of length 600mm.

Supply and fixing PVC waste pipe 32mm bore complete, all as specified

Supply and fixing in repairs 10 litres capacity PVC valveless , syphonic action type flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets.

Supply and fixing in repairs Vitreous china wash down water closet pan (pedestal pattern), white including fixing bolts,flush pipe and joints complete all as specified and directed by Engr-in-Charge.

Supply and fixing Vitreous china squatting pan of patern 'Orissa pattern ' size 580x440 mm white with integral foot rests, flush pipe including provn of cement concrete bedding and making good the dismantled surface in PCC 1:2:4 type B-I using 20mm graded stone aggregate as in repair.

Supply and fixing as in repair tubular towel rail, aluminium anodised 20 mm dia 'D' type 60 cm long between flanges

Supply and fixing as in repair Grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40gms)

Supply and fixing as in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

Supply and fixing in repair chromium plated shower roses 125mm long with arm swivel joints any size including fixing to steel pipe or union complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair vitreous china wash hand basin white flat back of size 550 x 400 mm including bracket, (pedestal pattern )cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified.

Supply and fixing in repairs plastic water closet seat cover ,white/ black,closed pattern with flats bottom and cover and mild steel chromium plated or aluminium hinging device,of approved make and quality etc complete.

Supply and fixing Toilet paper holder with flat recessed type stainless steel complete all as specified and directed.

Supply and fixing Hand Shower (Health Faucet) (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

Supply and fixing ball valves high pressure of PTMT with appoxy coated alluminium rod and high density plastic ball screwed for iron pipe 20mm bore fixed in repair all as specified minimum weight 210grms

Supply and fixing 15 mm dia bore in repairs brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed.

Demolition of Concrete ground floors and pavings n.exc 15cm thickness (below or above ground level) complete all as specified.

Material and labour for PCC (1:2:4) type B1 using 20mm graded stone agg as in surface channel and drains finished even and smooth

Material and labour for 100 mm thick PCC 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in hardstanding , path etc including finishing the rough surface without using extra cement and laid in alternate bays.

Plain cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in floor or paving 75mm thick,all as specified.

Forming contraction joints 100mm deep X 10mm wide , filled with sealing compound Grade A'

M&L for Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; , M-35 Grade complete all as specified.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete.

Material and labour for precast chequered tiles (factory made rectified) of size tiles 300mX300mmX25mm over 20mm thick cement screed layer in cement mortar 1:4 ,top layer glazed made in grey cement and pigment in required patterns(compressive strength not less than 250 kg per Sqm) as approved by Engr-in-charge complete, all as specified.

TMT Bars , 10mm dia over cut to length , bent to shape reqd including cranking bending and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips all as specified.

TMT bars 8 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns , hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia.

Material and labour for precast cement concrete type B1 (1:2:4) using 20mm graded stone aggragate as in cover slab, manhole cover etc all as directed by Engineer-in-Charge.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc and n.exc 10 Sqm on plan and n. exc 1.5 mtr in depth and getting out in any type of soil complete all as specified.

Returing filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm thick

Removing excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.50m above the starting point.

Demolition and breaking up drain pipes (salt glazed ware, AC or Reinforced concrete) set in cement mortar internal dia of pipe 150mm comolete all as specified and directed

Material and labour for 150mm bore/inner dia Double wall corrugated HDPE pipes (SN-4) with intergral socket and necessary fttings, laid in trenches jointed as per manufacturer instruction complete all as spd and directed at site.

Cleaning the blockage in IWC, EWC, incl roding CI pipe after opening the oval asses door of CI bend ,chamber etc upto septic tank and includingreplacing the chamber cover etc in position & removing the rubbish to a distance n.exc 50m all as specified and directed.

Desludging/dewatering/pumping/bailing out of contaminated water including cleaning of sludge, scum, silt (both organic and inorganic nature) and night soil from septic tank/soakage wells alongwith inlet/outlet chambers, manholes, soakage pits etc of any capacity after plugging the incoming sewage lines by suction (vaccum) type machine mounted on LCV facility of high pressure vaccum including removing the contaminated water in same tank to a place outside cantonment to a distance exceeding 50 mtr but not exceeding 100 mtr and burying in pits including rough excavation of pits and carriage of sludge to pits including spreading well in pits after burying of sludge, covering the pits with 25cm thick layer of earth and spreading bleaching powder over the covered area, complete all as specified and directed by Engineer-in-Charge.

M/S Virinder Sharma (BID ID -3052292)

VEER TRADERS (BID ID -3048073)

A K JAIN AND SONS (BID ID -3055489)

M/S SUSHEEL KUMAR Govt. CONTRACTOR (BID ID -3052060)