REPAIR AND MAINTENANCE OF FENCING, GATES, ETC OF EM INSTALLATIONS IN AGE BR I AREA

Amount

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for stone walling of random rubble, uncoursed well bonded, bedded and solidly hearted built in cement mortar 1:6 including demolition of rubbled stone masonry with all qoins arches , pillars etc built in cement mortar complete all as specified and directed.

All as per Srl item No.2 above but except stones - ditto- Note:- Serviceable stones obtained shall be reused in this item.

M&L for brick work with subclass 'B' bricks, straright or curved on plan exc 6m mean radius built in cement mortar 1:6 including demolition of brick work with all qoins arches , pillars etc built in cement mortar complete all as specified and directed.

All as per Srl item No.4 above but except bricks -ditto- Note:- Serviceable bricks obtained shall be reused in this item.

M&L for rendering 20mm thick cement plaster in cement mortar 1:4 on stone masonry surfaces, finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surfaces in cement mortar 1:6 finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparing the new plastered surfaces of wall and applying three coats of white wash on walls complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings n exc 15cm below or above ground floor complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in mass concrete, foundation filling, sub base,etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregates) as in mass concrete, top layer of hardstanding, paving, path etc; finshed even and smooth without using extra cement complete all as specified and directed.

M&L for PCC 1:2:4 (using 20 mm graded stone aggregates) as in roof kerbs or mud stops, rounded or chamfered on edge & embedding of chain link fencing complete all as specified and directed

M&L for hardcore of gauge not exc. 63 mm, deposited, spread and levelled in layers n.exc. 15 cm thick, watered and rammed to a true surface using broken stones or boulders, complete all as specified and directed.

Dismantling of posts or struts (wood, steel or RCC) any section, including taking out embedded portion and making good distrurbed ground in concrete complete all as specified and directed.

Dismantling of fencing wire mesh, any type complete all as specified and directed.

S&F mild steel angle iron as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire , etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling bolting or riveting, etc, and similar work and similar conforming to Fe-290 Gde E-165 complete all as specified and directed

S&F wind ties format including securing bolts posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wire etc, flat iron fillets (for securing wire mesh etc) including all necessay drilling bolting or riveting etc, and similar work confirming to Fe 410-0 or Fe 310-0 complete all as specified and directed.

Supply only mild steel galvanized chain link fencing of 4mm dia wire and 75mm X 75mm mesh size complete all as specified and directed Make:-TATA/SAIL/JINDAL

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and directed.

S&F MS framed work as in doors or gates designer type of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. oors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specicifed and directed.

S&F mild steel round bars 10mm dia and over, cut to length, bent to shape required, includinig cranking, bending spirally for hooping of columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips quality confirming to Fe-410 W complete all as specified and directed

S&F mild steel screw bolts (machine made) with hexagonal or sguare heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or screw nut n.exc 5 cm long dia of shank 12 mm complete all as specified and directed.

M&L for painting onsteel surfaces exc 10 cm in width or girth with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M&L for preparation of newly steel and iron surfaces of any description n.exc 10cm in width or girth when connected with other painting, applying two coats of synthetic enamel paint over a coat of red oxide paint complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint on old decorated steel surfaces exc 10 cm width or girth including preparation of surfaces complete all as specified and directed.

S&F in repairs stainless steel circular/square section incl plate/sheets/decorative items like dooms, cover cups etc as in frame work for road sign board complete all as specified and directed

S&F in repairs recto reflective sign face (Square or rectengular ) consist of 4mm thick aluminium composite panel sheet sign substrate and over all lamination using high intensity grade recto reflective media 3M or Unicorp make conforming to ASTM 4956 type -IV or above with text cutting as per direction of Engr-in-Charge. Using computerised cutter plotter & pneumatic automated squeeze roll applictor ) on overlay film or similar sheetng for text /graphics & symbol etc as per approved design and aluminum rivets, break away type nut/bolts (Each sign face shall be acked by staineless steel frame and stainless steel itmes will be measured and paid separately)

S&F mild steel door consisting of MS angle iron frame of 40x40x5mm with MS shutter with MS angle iron shutters frame 35 mm X 35 mm X 5 mm in two panel covered with 1.25 mm thick MS plain black sheet,sheet welded with 14X 3 mm thick flat all around of panel,30X30X5 mm tee fixed in between shutter partition, welded to with 2 Nos sliding door bolt of 16 mm dia 300 mm long with locking arrangement, 2 Nos of tower bolt of 200 mm long including MS angle iron frame 40mm x40mmx5 mm as in chowkhat with 6 Nos hold fast of flat iron 30mm X5 mm ,200 mm long with bottom flat iron of size 30mmx5mm and 100 mm size 4 Nos butt hinges including necessary cutting, welding, binding as required with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surfaces including taking down old chowkhat with shutter complete all as specified and as directed. [Single shutters of approx width 0.8 to 1.2 m and ht 1.9 to 2.10 M.]

S&F in repairs of 1.25mm thick laths steel rolling shutters incl top cover, anchoring rod, hasp and stapleand one shop coat of primer; erected in position as indicated complete (push and pull or manual type) complete all as specified and directed

S&F in repairs 110mm dia PVC(SWR) pipes single soketed in any length with adhesive joint fixed to floor or trenches including fittings complete all as specified and directed.

siddhant construction

M/s Mohan Singh

M/S vikas jain

A Raza Enterprises