ADDN/ ALTN TO KITCHEN BLDG NO O-7/10, O-5, NCC CLUB HOUSE AND PROVN OF PAVER BLOCK AT HAV TANK FORTWILLIAM UNDER GE (FW) KOLKATA

Amount

SCHEDULE A PART I(B/R PORTION) Taking down cement plaster on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Material and labour for 15 mm thick rendering in cement mortar (1:6), in two layers, each 10 mm thick, to fair faces of brick or concrete wall surfaces, top layer mixed with water proofing compound (@ 3 % by weight of cement or as per manufacture's instructions), finished rendering surface even and smooth(without using extra cement). (Note : Water proofing compound to be measured and paid separately as "Supply only")

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:4 finished rendering surfaces even and smooth (without using extra cement) complete all as specified and directed.

M&L rendering 10 mm thick in CM 1:3 on concrete as in ceiling/landing etc on concrete surface finish even and smooth without using extra cement with and including taking down cement or lime plaster of any description complete all as specified and directed .

Supplying Integral water proofing compound complete all as specified and directed.

Demolition of brick work/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and pre-cast concrete articles all as directed.

M&L brick work with Fly ash bricks old size brick straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with Fly ash bricks' old size brick straight or curved on plan to any radius built in cement mortar 1:4 as in half brick thick wall complete all as specified and directed.

M & L PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring benching to drain, coping, etc and the like edge slightly rounded or chamfered including necessary use and waste of form work complete all as specified and as directed.

Demolition of Reinforcement Cement Concrete(reinforcement cut as required to facilitate demolation) Roof, floors (other than ground floors), beams, staircase, landing, chajjas and similar suspended work complete all as specified and as directed.

M & L RCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall,beam and columns in floor, roof landing,, balconies,conopies, deck slab and shelves etc complete all as specified and directed.

Use and waste of formwork to sides and soffits of suspended slabs, floor slab, landing and similar work n. exc. 200 mm thick rough finished surfaces of concrete complete all as specified and directed.

S & F mild steel TMT bar 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, beam , slab etc hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clip complete all as specified and directed.

S & F mild steel deformed bar 6 to 8 mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed.

M & L 18 to 20 mm thick machine cut one side polished natural hard stone (Granite)any type in step, jambs, pillars,window cills, cooking plate from and simalr places etc like in 15 mm thick cement mortar 1:6 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed.

M & L glazed ceramic colour tiles size 450 mm x 300 mm x 6 to 7 mm thick on vertical surfaces such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed. complete all as specified and directed.

M&L non skid ceramic colour tiles of area of each tile exc .18 Sqm but n exc exc .38 Sqm and 8-10 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement complete including 15 mm thick screed bed cement mortar 1:6 complete all as specified and directed. all as specified and directed .

Demolition of cement concrete (un-reinforced) not exc 15cm thick in ground floor and paving (below or above ground level) complete all as specified and directed.

M & L 40 mm thick PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in flooring, laid in alternate bays, surface finished even and smooth using without extra cement complete all as specified and directed.

S & F 5 mm thick plain sheet glass ordinary quality and glazing with oil putty or wooden beads and aluminum clip etc in square area exc. 0.5 Sqm in each pane complete all as specified and directed.

Supply and fix rolled mild steel in roof trusses (framed), trussed, purlins, cane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance piece, cleats conforming to Fe-410-W( Gde E-250)quality-A- etc including notching, drilling, fitting riveting or welding all as specified and directed

Supply and fix mild steel framed work such as grills, gratings, etc with ends of bars shoulders and or riveted or forged in spikes, framed guard bars etc confirming to Fe-290(Gde E-165) all as specified and directed

S & F pre-painted galvatume aluminium zinc coating GI based corrugated steel 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

S&F 18-19 mm thick Plywood, grade BWR,type BB, fixed with screws to timber frame for wardrobe/shelf all as specified and directed

M&L Decorative laminate type -1, 0.9 mm thickness of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's as per specification and drawing.

S&F Stainless steel powder coated tray of various size for drawers to keep kitchen utensil with smoothly sliding arrangement complete all as specified

S & F Continuous (piano) hinges,brass, bright finish or electrogalvanised all as specified

S&F 100 mm Extruded brass handles,fabricated type polished all as specified

S&F 125 mm Hasp and staple, safety type,brass with mild steel hinge pin including bolt to hinge plate and fixed with screws all as specified.

S&F in repairs 4 levers brass body, lock ,drawer graded 1 size 50 mm, complete all as specified.and directed .

S&F in repairs aluminium 'E' channel for sliding drawer shutter of cub board in two way 300 mm long complete all as specified.and directed .

S&F 100 mm double action spring hinges (Hydraulic hinges) brass with phosphors bronze wire spring bright polished all as specified

Supply and fix aluminium (Die cast) body door closer hydraulically regulated, designation No 1 universal type, suitable for door shutters and of weight not more than 35 kg and fixed all as specified and directed.

S&F 75 mm Brass barrel tower bolts, with cast or sheet barrel and rolled or cast bolts and fixed all as specified.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm and n.exc.4.00 Sqm each wooden all as directed.

Supply and fix second class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered, put together with glue, pinned at joints all as specified and directed.

Supply and fix 30mm thick flush shutters solid core construction with block board core and plywood face panels on both side including lipping all around with 30mm x 6 mm thick fillets of second class hard wood all as specified and directed.

S&F 30 mm thick 2nd class harrd wood skelton shutters open rebated and prepare to receive glass, gauge etc, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, gauge etc, size of menbers of shutters as specified in SSR Part-I, Section 8.24(b) and as directed .

S&F stainless steel butt hinges 100mm medium weight all as directed.

S&F aluminium handle, cast type anodised 150mm size all as directed.

S&F 150mm aluminium anodised barrel tower bolts of extruded section.

S&F 300mm aluminium, anodised sliding door bolt with hasp, staple(bolt type) and fixing clip of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy all as directed complete all as directed.

S & F powder coating of any colour (Thickness or powder coating not less than 50 micron). Anodised aluminium window three track and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F in stainless steel wire cloth of 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples as directed by Engr-in-Charge.

S&F 4.8mm thick plain sheet glass ordinery quality and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified and directed by Engr-in-Charge.

S&F Stainless Steel Sink l.0mm thick Overall size 915mm x 460mm and Two Bowl size 410 mm x 355 mm x 165 mm for Kitchen or Laboratory with Plugs, Washers, Brass chromium plated Waste Fitting 32mm dia, PVC waste pipe, a Pair of Cast Iron Brackets duly Painted including Cutting and Pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including Taking down/out unserviceable Sink and connected Items, complete all as specified and as directed. Make : NIRALI/ Prayag ).

S&F in repair 35mm precast cement concrete type B0 1:2:4 using (12.5mm graded stone aggregate louvers and jallies including all mouldings set in CM 1:4 All as diected.

Supply and Fixing PVC solid wall lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per manufacturer’s specification and instruction and as directed .

Supply and Fixing 5mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame as per specification and drawing complete as directed..

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

Material and labour for preparation of new and previously un-treated steel surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and directed.

M&L for preparation of newly plastered ceiling surfaces and applying two coats of Oil Bound Distemper over a coat of alkali resistant primer complete all as specified and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of Oil Bound Distemper over a coat of alkali resistant primer applied over 1 to 2 mm thick plaster of Paris complete all as specified and directed .

M&L for applying one coat of cement base paint to old decorated (cement base painted) surfaces of wall including preparation of surface (by brooming down or steel wire brushing, scrapping down smoke, soot, moulds, moss, efflorescent salts, trading oil and greasy spots) complete all as specified and directed ..

S&F in repairs 15mm dia soap dish, square, acrylic body with chromium plated base complete all as specified and directed. (Make : Jaquar, Cat No : AKP-35731P / PARRYWARE, Cat No: T6403A1 / ESS ESS, Cat No: AC-103 / PRAYAG, Cat No: BA-35 or equivalent model in CERA /HINDWARE)

Supply and fix, as in repair, 15 mm bore bib taps, fancy type, chromium plated long neck cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.(Make : Jaguar or equivalent as approved by Accepting Officer).

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out in hard/ dense soil all as specified and directed.

Removing excavated material exc 250m but n exc. 500m and depositing where directed at a level n exc. 1.5 m above the starting point in any type of soil all as specified and directed.

M&L for 100mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) in floors complete all as specified and directed.

M&L for hardcore broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface all as specified and directed.

Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and as directed.

M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and as directed .

Shingle filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled, and blinded with earth and rammed including watering all as specified and as directed.

Sand filling under floors or in foundations including watering and consolidation all as specified and as directed .

M&L for Polythene film, black, 50micron laid in floors all as specified and as directed by the Engineer-in-Charge.

Material and labour for providing Plain Cement Concrete (1:3:6) type C2 using 40mm graded aggregate as in foundation, filling and mass concrete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B2,40mm graded aggregate finished even and smooth without using extra cement complete all as specified and as directed.

All as per item No 69 but Add or deduct for each 25mm over under 100mm thickness

M&L for Treating the backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contact with backfill to be measured) all as specified and as directed by the Engineer-in-Charge.

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface all as specified and as directed .

Dismantling of timber scantling 40 sq cm and over in section, in any position in framed work all as directed.

Dismantling of timber fillets rails, posts, rafters, purlins etc under 40 Sqcm in section, in any position in unframed work all as directed.

S&F wooden flooring system, surface board of size 21mm thick , 60 to 70mm width and in random length in tounge and groove shape incl with under frame is made of commercial quality pine wood runner of 70 mm to 45 mm treated with anti termite solution and fixed on bottom side with 10mm thick air cushioning pads by stable through two wings at 300mm C/C.( Surface board will be imported maple wood/ white oak teak)

M&L rendering 10mm thick in CM 1:6 on fair faces of brick surface finished even and smooth without using extra cement complete all as specified and directed.

M&L for providing and fixing Stainless steel railing, grade 304 with various type of elegent design/ pattern with pipes/rod/ strip for different staircase, cutouts area, balcony etc fixed by inserting in holes of required size and grouted in cement mortar 1:3/bolt, nuts and to be covered with stainless steel cap of required size all as directed and specified.

M&L 25 mm thick pre polished coloured chequred tiles of size 400X400 jointed and pointed in neat cement slurry with white or coloured to match including over 20 mm thick screed bed CM 1:6 completed all as directed.

M&L Preparing old decorated Plaster Surfaces of Wall and applying One Coat of oil bound distemper complete all as specified and as directed.

S&F 4mm thick design `E' board of size 600x600mm incl aluminium snap grid made of aluminium main `T' 38x25x2mm thick and cross Tee and angle of section 24.5x24.5x1.4mm thick incl proper hanging arrangement (with 4mm dia galvanised iron wire and suitable adjuster) and incl applying two coat of OBD in repair all as directed ..

Excavation in trench not exceeding 1.5 M wide and not exceeding 1.5M in depth for sewage line, manhole etc not exceeding 10 sqm on plan and getting out in any type of soil complete all as specified and as directed.

Returning, filling in, including spreading, watering and well ramming in layers n. exc 25 cm thick in any type of soil complete all as specified and as directed.

Material and labour for providing Plain Cement Concrete (1:4:8) type D2 using 40 mm graded aggregate as in foundation, filling and mass concrete all as specified and directed.

Form work Use and waste to sides of concrete foundation, footing, bases of columns, plinth beam, side and soffits of plinth beam and similar works in vertical or to batter of fair finished surfaces complete all as specified and directed.

Form Work Use and waste to sides of columns, pillars etc. of fair finished surfaces complete all as specified and directed.

M&L Nominal Mix Type B1 1:2:4 (20 mm graded aggregate) aggregate) as in column footing including raft footings, foundation, plinth beam, bases of columns etc. complete all as specified and directed.

Material and labour for providing Nominal Mix (1: 2 : 4) type B1 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m all as specified and directed.

Supply and fix vitrified tiles(light shade) of 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqmas in floor set and jointed in neat cement slurry @ 3 kg per Sqm and pointed in coloured cement to match the shade of the tiles over and incl. 15 mm screed bed in CM (1:6) complete all as directed.

S&F Framed work Fe-410-W(Gde-E-250) quality-A as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening all as specified.

S & F pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges , valley gutter, Sun shed etc fixed with self tapping screws as specified.

S & F 10-12 mm thick gypsum board false ceiling including 0.55 mm thick GI perimeter channel, GI channel tray frame work having one flange of 20mm and another flange of 30mm with web of 27mm, fixed to surrounding wall using nylon sleeves and screws @ 450mm centre to centre / GI intermediate channel of size 45mm x 0.90mm thick with two flange of 15mm each suspended from the soffit of roof slab/ truss @1220mm c/c with MS angle of suitable size fixed to soffit of ceiling with GI cleat and expansion fasteners with and including ceiling section ( not exc 1.2 metre length ) of 0.55 mm thickness having kurled web of 50 mm and flange of 25 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel @ 457 mm centre to centre with necessary nuts and bolts and gypsum board scrrewed to ceiling section with stainless steel screws @ 230mm c/c including applying two coats of oil bound distemper over a coat of primer over 1.5-2 mm thick putty on ceiling surfaces complete all as specified and directed.

Material and labour for providing 35 mm thick (measured solid) Precast Cement Concrete (1:2:4) type BO using 12.5 mm graded aggregate as in louvers and jallies, including all mouldings, framesets in cement mortar (1:6) all as specified and directed

Material and labour for preparation of new and previously un-treated wood and wood base surfaces of any description, not otherwise described over 10cmwidth or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and directed.

SCHEDULE A PARTII(E/M PORTION) Taking down copper/ aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceilling roses, pendants , regulators, sockets etc excluding light fitting for taking credit removing from site and making good disturbed surface of walls, floors etc.

M & L for point wiring with FRLSH PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC casing & caping / PVC contut terminated in PVC block 50 mm deep (sunken) for fixing of switches, sockets, fan regulators etc (PVC box of required size will be measured and paid under relavent item) for the following: -

One light point or one fan point or bell point controlled by one switch or bell push

One 3/5 pin socket outlet, 5 Amp independent

One 3/5 pin socket outlet, 5 Amp on the same board with other switches

M & L for point wiring with FRLSH grade PVC insulated unsheathed multistranded copper conductor cables of 2.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 2.5 sqmm size through and including PVC casing & caping terminated in and including PVC block 50 mm deep (sunken) for fixing of switches/ sockets for one 3 pin socket outlet, 15 Amps, independent .

M & L for concealed point wiring with FRLSH grade PVC insulated unsheathed multistranded copper conductor cables of 1.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 1.5 sqmm size through and including PVC conduit terminated in modular switch boards for fixing of switches, sockets, fan regulators etc for the following [Note: - Modular switch boards shall be measured and paid separately]: -

One light point or one fan point controlled by one switch

One 3/5 pin socket outlet, 5 Amp independent

One 3/5 pin socket outlet, 5 Amp on the same board with other switches

M & L for concealed point wiring with FRLSH grade PVC insulated unsheathed multistranded copper conductor cables of 2.5 sqmm size alongwith one earth continuity conductor with PVC insulated unsheathed multistranded copper conductor cable of 2.5 sqmm size through and including PVC conduit terminated in modular switch boards for fixing of switches/ sockets for one 3 pin socket outlet, 15 Amps, independent [Note: - Modular switch boards shall be measured and paid separately]

S & F Modular Switch 1 way 6 A, 1 module complete all as specified and directed.

S & F Modular Switch 1 way 16 A, 1 module complete all as specified and directed.

S & F Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F Modular Fan step regulator, 120 watt, 2 module complete all as specified and directed.

S & F Modular Bell push 6A, 1 modulecomplete all as specified and directed.

S & F Modular Blank plate, 1 modulecomplete all as specified and directed.

S & F Modular type White cover plate with frame 1 module complete all as specified and directed.

S & F Modular type White cover plate with frame 2 modulecomplete all as specified and directed.

S & F Modular type White cover plate with frame 3 module complete all as specified and directed.

S & F Modular type White cover plate with frame 4 module complete all as specified and directed.

S & F Modular type White cover plate with frame 6 module complete all as specified and directed.

S & F Modular type White cover plate with frame 8 module complete all as specified and directed.

S & F Modular type White cover plate with frame 12 module complete all as specified and directed.

S & F Modular type Metal Flush box 1/2 module complete all as specified and directed.

S & F Modular type Metal Flush box 3 module complete all as specified and directed.

S & F Modular type Metal Flush box 4 module complete all as specified and directed.

S & F Modular type Metal Flush box 6 module complete all as specified and directed.

S & F Modular type Metal Flush box 8 module complete all as specified and directed.

S & F Modular type Metal Flush box 12 module complete all as specified and directed.

S & F Switch piano, flush type single pole, one way 5 Amp complete all as specified and directed.

S & F Socket outlet 2 in 1, 3 pin, 5 Amp vcomplete all as specified and directed.

S & F Switch socket combination 2 in 1, 5 Amp flush type complete all as specified and directed.

S & F Bell push, flush type, 5 amp complete all as specified and directed.

S & F Switch socket combination 5A/ 16A, 5 in 1flush type complete all as specified and directed.

S & F Switch piano, flush type single pole, one way 15 Amp complete all as specified and directed.

S & F Socket outlet 2 in 1, 3 pin, 5 and 15 Amp flush type complete all as specified and directed.

S & F Bell , AC, 230 Volts, single pole complete all as specified and directed.

S & F Musical Call Bell acomplete all as specified and directed.

S & F stepped type electronic fan regulator flush type complete all as specified and directed.

S & F Ceiling rose, 3 terminal PVC insulated body complete all as specified and directed.

S & F in repair Modular Switch 1 way 6 A, 1 module complete all as specified and directed.

S & F in repair Modular Switch 1 way 16 A, 1 module complete all as specified and directed.

S & F in repair Modular Socket 6 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F in repair Modular Socket 6 A/ 16 A, 2/3 pin combined 2 module complete all as specified and directed.

S & F in repair Fan step regulator, 120 watt, 2 module complete all as specified and directed.

Supply and fixing LED lights fitting 1x 20W, 220V,warm light AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specifide and directed. Make: Philips / Bajaj /Havells.

S & F in repair LED tube light fitting 10 watt, warm light mounted on wall / ceiling connected with insulated unsheathed flexible copper wire of suitable size (length not exceeding 0.5 m) from ceiling rose complete all as specified and directed. Make: Philips/Bajaj/Havells

S & F in repair Surface mounting LED Slim round down lighter made of powder coated aluminium housing with high efficient LEDs & Glare free opal diffuser,IP20 15W Make: Havells/ philips / Crompton.

S & F in repair Recess mounting LED Slim round down lighter made of slim-fit low profile downlights are engineered to deliver superior light output and uniformity utilising the latest edge-lit led with high efficient LEDs & Glare free opal diffuser,IP20 15W make Havells EDGEPRORDDLR15WLED857S or equivalent make Philips/ Crompton

S & F in repair Recess mounting LED Slim round down lighter made of slim-fit low profile downlights are engineered to deliver superior light output and uniformity utilising the latest edge-lit led with high efficient LEDs & Glare free opal diffuser, IP20 6W make Havells EDGEPRORDDLR6WLED857S or equivalent make Philips/ Crompton

S & F in repair LED wall mounted spot focusing light fitting 9 above watt, colour temperature 2700K, mounted on wall / ceiling connected with insulated unsheathed flexible copper wire of suitable size (length not exceeding 0.5 m) from ceiling rose complete all as specified and directed.

S&F in repair picture LED lights with color temperature 3000 K suitable for 10 W metal and synthetic material lumen 500 lm Model: 48043/30/86 Make: Philips or equivalent of havells / Crompton complete all as directed

S & F ceiling fans complete with all accessories 230 volt single phase 1200mm sweep with down rod any size , canopy, fan blades and accessories, BEE 5 Star Rated and connecting up including provision of PVC insulated, sheathed round flexible wire with multi stranded copper conductor of size 0.50 sqmm , 3 core, 1100 Volts grade, from ceiling rose / connector to fan complete all as specified and directed.

Taking down plastering on lathing (other than wire-netting), without removing lathing, in lime mortar (one side only measured in cases where both sides are plastered) complete all as specified and directed.

All as per Ser Item No 143, but in cement lime or cement mortar

M&L nominal mix type B1 1:2:4 (20 mm grade aggregate) as in columns, pillars etc complete all as specified and directed

S&F PVC lipping edge tape decorative type 20-25 mm width and 0.5-1.00 mm thick all as specified and directed.

RAJ ENTERPRISE

KWALITY CONSTRUCTION

MS AP CONSTRUTION AND CO

UNITED ENGINEERS

PRABIR TRADERS

SOMANI BUILDERS

MAZUMDER ENTERPRISE