Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹67.5 LAccepted-AOC | ₹67.5 L | L1 | Accepted-AOC L1 Bidder |
| 2 | L2₹70.9 LRejected-Finance C O GENERAL DAIRY VILLAGE BARAGAON SRI GANGANAGAR 335 001 | GANGANAGAR | RAJASTHAN | 335001 | ₹70.9 L | L2 | Rejected-Finance Not the lowest Bidder |
| Sl No | Description | Qty | Unit | PAREEK AND COMPANY L2 | GHANSHYAM BHADU L1 |
|---|---|---|---|---|---|
| 1.00 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed by Engineer-in-Charge. | 719.25 | Sqm | 10 ₹7,192.50 | 25 ₹17,981.25 |
| 2.00 | Excavation in trenches n.exc. 1.5m wide and n.exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 Sqm on plan and n.exc 1.5 m in depth and getting out in getting out in soft / loose soil complete all as specified and as directed by Engineer-in-Charge. | 320.9 | Cum | 150 ₹48,135 | 240 ₹77,016 |
| 3.00 | All as per Ser item No 2.00 above but exc 1.5 mtr and n.exc 3 mtr in depth complete all as specified and as directed by Engineer-in-Charge. | 49.22 | Cum | 200 ₹9,844 | 270 ₹13,289.40 |
| 4.00 | M&L for PCC, (1:3:6), type C2, using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified and as directed by Engineer-in-Charge. | 18 | Cum | 3,000 ₹54,000 | 2,900 ₹52,200 |
| 5.00 | M&L PCC (1:4:8) using 40mm graded stone aggregate as sub base and in foundations, filling and mass concret complete all as specified & directed by Engr-in-charge. | 11 | Cum | 2,200 ₹24,200 | 2,500 ₹27,500 |
| 6.00 | M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge. | 304 | Sqm | 200 ₹60,800 | 250 ₹76,000 |
| 7.00 | M&L for formwork to sides of pillars, columns etc; rough finish surface of concrete square, rectangular or polygonal complete all as specified and as directed by Engineer-in-Charge. | 187.5 | Sqm | 200 ₹37,500 | 250 ₹46,875 |
| 8.00 | M&L for formwork to sides and soffits of floor or roof beams, beam hunchings, girders, bressummers, lintels, cantilevers, etc. also splays between floors and beams, etc. rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge. | 172 | Sqm | 200 ₹34,400 | 280 ₹48,160 |
| 9.00 | M&L for formwork to chajjas, troughts and similar items including edges rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge. | 11.35 | Sqm | 200 ₹2,270 | 250 ₹2,837.50 |
| 10.00 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200 mm thick (horizontal or sloping) rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge. | 225 | Sqm | 200 ₹45,000 | 280 ₹63,000 |
Updated dates
Tender Value
Refer Docs
EMD Value
₹1.4 L
Closing Date
24 Jan 2026, 6:00 pmClosed
HQ CWE SRI GANGANAGAR
HQ CWE POST BOX 48 SRI GANGANAGAR-335001 (Rajasthan)
PROVN OF CENTRAL BATHROOM AND TOILET FACILITY AT CATF AND PROVN OF DEFI SINGLE LIVING JCOs ACCN OF INF BN (OTM-I) LALGARH JATTAN MIL STN
2025_MES_746396_1
CA NO CWE SGNR/TOKEN-101 OF 2025-26
Open Tender
Electrical and Maintenance Works
180 days
GE LALGARH JATTAN
AS per NIT
8 documents required · 8 mandatory
₹1,000
GE LALGARH JATTAN
₹1.4 L
Yes
23 Feb 2026
27 Dec 2025
26 Jan 2026
27 Dec 2025
24 Jan 2026
10 Jan 2026
Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft/loose soil complete all as specified and directed by Engineer-in-Charge.
Excavation in trenches n.exc. 1.5m wide and n.exc 1.50 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc. 10 Sqm on plan and n.exc 1.5 m in depth and getting out in getting out in soft / loose soil complete all as specified and as directed by Engineer-in-Charge.
All as per Ser item No 2.00 above but exc 1.5 mtr and n.exc 3 mtr in depth complete all as specified and as directed by Engineer-in-Charge.
M&L for PCC, (1:3:6), type C2, using 40mm graded stone aggregate as in foundation, filling & mass concrete complete all as specified and as directed by Engineer-in-Charge.
M&L PCC (1:4:8) using 40mm graded stone aggregate as sub base and in foundations, filling and mass concret complete all as specified & directed by Engr-in-charge.
M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge.
M&L for formwork to sides of pillars, columns etc; rough finish surface of concrete square, rectangular or polygonal complete all as specified and as directed by Engineer-in-Charge.
M&L for formwork to sides and soffits of floor or roof beams, beam hunchings, girders, bressummers, lintels, cantilevers, etc. also splays between floors and beams, etc. rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge.
M&L for formwork to chajjas, troughts and similar items including edges rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge.
M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exc 200 mm thick (horizontal or sloping) rough finish surface of concrete flat complete all as specified and as directed by Engineer-in-Charge.
M&L for fromwork to edges of concrete flats, treads breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n.exc 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10 cm but n.exc 20 cm wide, rough finished surfaces of concrete complete all as specified and as directed by Engineer-in-Charge.
M&L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed by Engineer-in-Charge.
All as per Ser item No 12.00 above but 5 mm dia and over upto and including 10mm dia as in stirrups, spaces & binders complete all as specified and as directed by Engineer-in-Charge.
M&L for reinforced cement concrete (design mix) M-25 using 20mm graded stone aggregrate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, pillers etc complete all as specified and as directed by Engineer-in-Charge. Note : Reinforcement shall be measured and paid seperately under respective item of BoQ.
M&L for reinforced cement concrete (design mix) M-25 using 20mm graded stone aggregrate in columns, pillers complete all as specified and as directed by Engineer-in-Charge.
M&L for reinforced cement concrete (design mix) M-25 using 20mm graded stone aggregrate in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and as directed by Engineer-in-Charge.
M&L for reinforced cement concrete (design mix) M-25 using 20mm graded stone aggregrate in Chajjas; complete all as specified and as directed by Engineer-in-Charge..
M&L for reinforced cement concrete (design mix) M-25 using 20mm graded stone aggregrate in slabs supported on walls, beams and columns in floors, roofs, Stair case, landings, balconies, canopies, deck slabs and in shelves and the like; complete all as specified and as directed by Engineer-in-Charge..
M&L for brick work with fly ash bricks, of old size bricks, straight or curved exc. 6 m mean radius built in CM (1:6) complete all as specified and as directed by Engineer-in-Charge.
M&L for brick work with fly ash bricks, of old size bricks, straight or curved exc. 6 m mean radius built in CM (1:4) complete all as specified and as directed by Engineer-in-Charge.
M&L brick work with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, buit in CM (1:4) complete all as specified and as directed by Engineer-in-Charge.
Returning, filling in, including spreading levelling including watering & well ramming in layers n. exc 25 cm all in soil complete all as specified and as directed by Engineer-in-Charge.
Spreading and levelling in layers n.exc 25cm thick and well ramming including watering as required under floors; all as directed. (in floor with available earth from excavation approved by Engr-in-Charge.
Removing excavated materials n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed by Engineer-in-Charge.
M&L for treating the top surface of filled earth @ 5 litres emulsion per square metre of surface complete all as specified and as directed by Engineer-in-Charge.
M&L for treating the soil under plinth protection @5 litres of emulsion per square metre of surface area complete all as specified and as directed by Engineer-in-Charge.
M&L for hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc.15cm thick,watered and rammed to a true surface in broken stone or boulders (15cm compacted thickness) complete all as specified and as directed by Engineer-in-Charge.
M&L for 75 mm thick PCC, (1:3:6), type C-1, using 20 mm graded crushed stone aggregate as in plinth protection finished even and smooth with using extra cement with & including 10 mm wide, 30 mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture complete all as specified and as directed by Engineer-in-Charge.
M&L for 75mm thick PCC, (1:4:8), type D2, using 40mm graded stone aggregate as in sub base below floors complete all as specified and as directed by Engineer-in-Charge.
M&L for 25 mm thick PCC, (1:2:4), type B-0, using 12.5 mm graded stone aggregate as in floor or laid under floor etc complete all as specified and as directed by Engineer-in-Charge.
M&L for joint free Non-skid Ceramic coloured tiles 7 to 8 mm thick, area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. over and including 15 mm thick screed bedding in cement mortar (1:6), set and jointed in neat cement slurry and pointed in white or coloured cement to match the floor complete all as specified and as directed by Engineer-in-Charge.
M&L for joint free glazed Ceramic coloured tiles of size 450 x 350 x 7 mm thick on vertical surfaces such as skirting / dados over and including 10 mm thick backing coat in cement mortar (1:4) set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and as directed by Engineer-in-Charge.
M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 15 mm thick screed bedding in cement mortar (1:6), set and jointed in neat cement slurry and pointed in coloured cement to match the floor complete all as specified and as directed by Engineer-in-Charge.
M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tile exc 0.18 Sqm but not exc 0.38 Sqm in floor over and including 10 mm thick rendering on vertical surface in cement mortar (1:4), set and jointed in neat cement slurry and pointed in coloured cement to match complete all as specified and as directed by Engineer-in-Charge.
M&L for machine cut pre polished Kota stone slab flooring 20-25mm thick (size 550 x 550 mm) over and including 15mm thick screed bed in CM (1:6) laid and and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed by Engineer-in-Charge.
M & L Machine cut pre polished kota stone slab 20-25mm thick in riser of steps, skirting, dado laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified and as directed by Engineer-in-Charge.
M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including rounding to edges of stone slabs (one edge) complete all as specified and as directed by Engineer-in-Charge.
Rounding to edges of stone sabs one edgs, such as in steps, cookng plateform and other similar situations all as specified and directed .
Supply & fixing HDHMR Board , 18/19mm thick both side decorative laminated, density over 850kg/cum, having a class A fire rating, grade 2 quality, interior grade, including fixed with screws , L bend or necessary fittings to mount on wall or to frame work as in Kitchen cup board Shutter / shelves / cabinet etc complete all as per direction of Engineer- in-Charge
Supply and fixing Magnetic catcher fixed with steel screw complete all as specified and as directed by Engineer-in-charge.
Supply & fixing Continuous (piano) hinges, stainless steel, bright finish, width of flap when open 30mm complete all as specified and as directed by Engineer-in-charge .
Supply & fixing 200 mm size stainless steel ( Grade 304 )Drawer handles, projection drop 65mm on screwed plate complete all as specified and as directed by Engineer-in-charge .
S & F for Steel rolling shutters of thickness 1 mm , with ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and as directed by Engineer-in-Charge.
S & F for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and as directed by Engineer-in-Charge.
M&L for rendering, 10 mm thick on brick work or concrete surfaces in cement mortar (1:6) on wall finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.
M&L for 5 mm thick rendering in cement mortar (1:4) (as second coat), over and including 10 mm thick rendering in cement mortar (1:6) (as first coat) of fair faces of brick work or concrete surfaces of wall, incl mixing only liquid water proofing compound in second layer only as per manufactures instruction, finished the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note :- WPC Shall be measured and paid separately as supply only.
M&L for rendering, 5 mm thick on brick work or concrete surfaces in cement mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge..
M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:4 on wall, finished even and smooth complete all as sepecified and directed.
M&L for rendering, 15 mm thick on brick work or concrete surfaces in cement mortar 1:6 on wall, finished even and smooth complete all as sepecified and directed.
Supply only liquid water proofing compound all as specified and directed by Engr-in-Charge.
M&L for preparation and applying three coats of white wash on newly plastered surfaces of wall complete all as specified and as directed by Engineer-in-Charge.
M&L for preparation and applying three coats of white wash on newly plastered surfaces of ceiling complete all as sepecified and directed by Engineer-in-Charge.
M&L for two coats of acrylic distemper on new plastered surfaces of walls paint over 3mm thick wall care putty over a coat of primer including preparation of surfaces complete all as specified and as directed by Engineer-in-Charge.
M&L for applying two coat of weather proof exterior emulsion paint ( shade as approved by GE) with highlighter of any approved shade, @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/ cantilevers/balcony etc surfaces over wall care putty (thickness very from 1.5 to 2.5 mm as required for desirable smoothness and levelling of surfaces in two or more layers) on newly plastered surfaces of wall including preparation of surface complete all as specified & directed by Engr-in-charge.
Material and labour for applying 10mm thick rendering /screed in cement mortar (1:4) including mixing of liquid WPC in mortar @ as per manufacturer instruction per bag of cement of 50kg and finished even and smooth without using extra cement complete all as specified and as directed by the Engineer-in-Charge. Note :- WPC shall be measured & paid separately as Supply only under relevant item.
OVERLAY- PU BASED ELASTOMERIC LIQUIED MEMBRANE SYSTEM FOR EXPOSED ROOF : Providing and applying polyurethane liquid roof waterproofing with improved water ponding capability, elastomeric high build liquid membrane for concrete roofs for exterior wall and exposed surface with solid content not less than 80% and solar reflective index not less than 106 as per (ASTM E1980-19)/tear strength ~20 N/mm (Free film, 14 days, +30 degree C) (ASTM D624) and tensile strength >= 2 N/mm2 (ASTM D4541), elongation 350 to 400% as per ASTM D412 and crack bridging ability upto 2mm. (a) After proper surface preparation, Apply one coat of Primer for PU coating as per manufacturers specification. (b) Apply 1st coat of ShaliUrethane® BTD (white) @ 650 gm / m²(minimum) or equivalent by brush / roller while prime surface is tacky, Spread waterproofing reinforced Glass Fiber mash of 45 GSM with overlaps of 50 mm in both directions when the surface is still tacky. Allow 1st coat to dry. (c ) Apply 2nd & 3rd coat of ShaliUrethane® BTD (white) @ 650 gm / m² (minimum) or equivalent by brush/roller. Make : Fosroc/Sika/Choksey/Bostik/STP/ Asian Paints/Berger Paints Note : (i) The Minimum dry film thickness (DFT) of roof treatment shall be 1.5mm if any shortfall in thickness of above treatment the same shall be achieved by additional coat. (ii) The procurement of material and execution of the work of water proofing treatment shall be carried out by authorised applicator approved by GE. (iii) The manufacturer/authorised applicator shall give a warranty for the performance & durability for 10 years.
M&L PCC, 1:2:4, type B-1, using 20mm graded stone aggregate as in roof kerbs or mud stops, and like rounded or chamfered on edges including necessary form work etc complete all as specified & directed by Engr-in-Charge.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasterners of required dia and length complete as per direction of Engr-in-charge. Note: - M.S hold fast/lugs or SS dash fasterners shall be paid for separately.
S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasterners of required dia and length complete as per direction of Engr-in-charge. Note: - M.S hold fast/lugs or SS dash fasterners shall be paid for separately.
M&L for framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spiles; framed guard bars; barred iron doors; ladders; framed balusteres; walk ways, railings; framework of water tanks and similar work confirming to Fe. 290, Gde-E-165 with complete all as specified and as directed by Engineer-in-Charge.
S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge including supply and fixing following items :- (a) Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf and table 6 of BIS 12817-2020 BIS Marked. (b) Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm as per BIS 12833. (c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf. (d) Stainless steel (304 Grade) finished sliding bold 300 mm-1 No per leaf, 16 mm dia as per BIS clause (iii) of BIS 15834-2020. (e) Stainless steel (304 Grade) Finished Floor door stopper 140 mm -1 Nos per leaf.
S&F for Factory made single extruded WPC (Wood Polymer Composite) glazed and skeleton plain door shutter of 35 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2 , modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. Including supply and fixing of stainless steel 304 Grade (natural finish) wire cloth complete all as direction of Engineer-in -Charge including supply and fixing of following items :- (a) Stainless steel (304 Grade) finished butt Hinges 100 mm, 4 Nos per leaf and table 6 of BIS 12817-2020 BIS Marked. (b) Stainless steel (304 Grade) finished square tower bold 200 mm long-2 Nos per leaf as per table 01 dia of bolt 12 mm as per BIS 12833. (c) Stainless steel (304 Grade) Finished Handles 200 mm-2 Nos per leaf. (d) Stainless steel (304 Grade) finished sliding bold 300 mm-1 No per leaf, 16 mm dia as per BIS clause (iii) of BIS 15834-2020. (e) Stainless steel (304 Grade) Finished Floor door stopper-1 140mm Nos per leaf. (f) Stainless steel (304 Grade) wire cloth fixing as per manufacturer's instructions
S&F for Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flameof Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws and 02 Nos (Per leaf) SS 150 mm long Tower bolt and 02 Nos per leaf SS 150 mm long handle complete all as specified and directed.
S&F for 300mm ordinary rat tail rod pattern springs including roller and roller plate complete mild steel fixed complete complete all as specified and as directed by Engineer-in-Charge.
S&F for 1st class hard wood (Sal) or any other 1st class hard wood articles not exceeding 200 cubic centimetre each as small fittings such as shaped door and window stops and the like, including necessary labour etc complete all as specified and as directed by Engineer-in-Charge.
S&F for stainless steel wire cloth 0.36 nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed by Engineer-in-Charge.
S&F for 4.8 mm thick sheet glass ordinary quality and glazing with spring clips in metal surrounds and oil putty in squares exceeding 0.50 sqm in each pane with solar control film 25 micron reflective size stick to glass panes asper instructions of manufacturers complete all as specified and as directed by Engineer-in-Charge.
S&F for 5 mm thick figured glass, pin head type and glazing with spring clips in metal surrounds and oil putty in squares not exceeding 0.50 sqm in each pane complete all as specified and as directed by Engineer-in-Charge.
S&F 4 mm Sheet glass,ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane, all as specified and as directed.
M&L for preparation of new steel surface of any description not otherwise described over 10 cm width or girth and apply two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.
S&F in vitreous china squatting pan Orissa pattern size 580 x 440 mm white with integral foot rests including CI 'P' trap set in and including concrete fixed complete all as specified and directed by Engineer-in-Charge.
Supply and fixing vitreous china premium/1st quality wall hung water closet with P trap white/ivory/off white including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc., and incl. plastic soft close seat cover as recommended by manufacturer for particular model closed pattern with flat bottom etc; and incl S&F of all necessary accessories set like rag bolts/gel gasket/hinges etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete all as specified and directed by Engineer-in-Charge.
Supply and fixing concealed flushing cistern of PVC 8 ltr. cap with dual flushing system, valveless syphonic action type, with inlet/outlet, ball valve, float and including brackets and connection to pipe etc. and incl S&F of all necessary accessories/installation kit and 'S' type drain pipe connetion set for wall hung WC etc as recommended by manufacturer for fixing, packing and including S&F of actuator knob/flush plates and and taking down existing of any description/size complete all as specified and directed by Engineer-in-Charge.
Supply and fixing in PVC valve less, syphonic action type flushing cistern,10 ltrs capacity low level, white, with inlet ball valve, float, handle and telescopic pipe and connection to pipe and flush pipe of polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed by Engr-in-charge.
Supply and fixing vitreous china premium/1st quality wash basin (under counter), white/ivory/off white, size 580x430 mm including S&F all accessories as recommended by manufacturer and incl. brass CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and complete fixed in position in all respect as per manufacturer's instructions and taking down existing of any description/size complete all as directed by Engineer-in-charge.
Supply and fixing Vitreous China Urinal, Half stall type, white with grating & union for discahrge pipe including spreader of chromium plated brass for fixing with 15 mm dia pipe (minimum wt 60gms) but excluding flushing cistern, flush pipe & waste pipe but fixing only automatic flushing cistern with bracket, flush pipe etc complete all as specified and directed by Engineering-in-Charge.
S&F Swan neck pillar tap, fancy type, cast copper alloy chromium plated with capston head, screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe of 15 mm bore complete all as specified and directed by Engineer-in-Charge. Note : - Weight not less than 450 gms
S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and as directed by Engineer-in-Charge.
S&F stainless steel chromium plated jet spray (butter fly or " L" bend) suitable for EWC including 1m tube and necessary nut bolts complete all as specified and as directed by Engineer-in-charge.
S&F 15 mm dia stop valve, fany type chromium plated with long shank and cup (concealed type), cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and as directed by Engineer-in-Charge..
S&F 15 mm dia stop valve/angle valve, fancy type chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe complete all as specified and as directed by Engineer-in-Charge.
S&F bib tap 15mm bore cast copper alloy chromium plated long body fancy type with capston head and cup screwed down, hand operated, screwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge.
S&F15 mm two-way bore bib taps chromium plated cast copper alloy with crtuch or butterfly handle, screwed down, screwded for iron pipe or for brass ferrule and fixed.
Supply and fixing single liver basin mixer with popup waste system & 450mm long braided hoses, fency type, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure, with long screwed shanks and fly nuts, screwed for 15mm bore of iron pipe complete all as specified and as directed by Engineer-in-charge.
Supply and fixing single lever High concealed diverter flow consisting of exposed part kit with operating lever, wall flange & button and concealed body, cartdge sleeve and also including bath spout with flange chromium plated ,screwed down, high pressure complete all as specified and as directed by Engineer-in-charge.
Supply and fixing Chromium plated overhead rain shower 200 mm x 200 mm with shower arm of 300mm long 20mm dia round shape with 90º bend for wall mounted shower with flange of same make and incl all necessary accessories as recommended by manufacturer for fixing and taking down existing of any description/size complete in all respect all as specified.
S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed by Engineer-in-Charge.
S&F PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and as directed by Engineer-in-Charge.
Supply and fixing glass corner shelf with CP brackets and CP railingcomplete all as specified and directed by Engineer-in-Charge.
S&F in repair PVC bathroom cabinet mirror of size 450x350mm all as specified and directed by Engineer -in-charge
S&F in chromium plated fancy type soap dish 10 cm/15 cm complete all as specified and directed by Engineer-in-Charge
S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed by Engineer-in-Charge.
S&F brass hat pegs, solid body, 125 mm to 175 mm (5 legs) complete all as specified and as directed by Engineer-in-Charge.
S&F 25 mm dia gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed including of all fitting complete all as specified & directed by Engr-in-Charge.
S&F for Rotational moulded polythene water storage tank 1000 ltr capacity vertical with closed top hoisted and fixed in position all as specified in SSR part-I All as directed and including 20 mm bore PTMT float valve, connection nipple 2 Nos complete all as specified and directed.
S&F rotational moulded polythene water storage tank 500 ltr capacity of tripple layer vertical with closed top (ISI Marked) hoisted and fixed in position all as specified in SSR part-I. complete all as specified and as directed by Engineer-in-Charge.
S&F ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed in 20mm dia bore pipe complete all as specified and as directed by Engineer-in-Charge.
S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 20mm bore fixed in repair complete all as specified and as directed by Engineer-in-Charge.
S&F gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 15mm bore fixed in repair complete all as specified and as directed by Engineer-in-Charge.
S&F Supplying and laying of 20 mm (outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified and as directed by Engineer-in-Charge.
S&F Supplying and laying of 25 mm (outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified and as directed by Engineer-in-Charge.
S&F Supplying and laying of 32 mm (outer dia) CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified complete all as specified and as directed by Engineer-in-Charge.
S&F 32 mm dia low density polyethylene pipes (LDPE) of pressure rating 6 kgf/cm2 fixed complete to walls, ceilings or in floors all as directed.
Supply & fixing 110mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls/tranches with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant including bends, socket , Y junction, Tee , cowl etc complete all as specified and as directed by Engineer-in- charge complete including low carbon hot roll gauge corrected oil pickled & drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanised and Zn, Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed. (Note: Detail of Pipe supporting system is all as per Drg NO -BTD-916). Note:-UPVC PIPE AND FITTING / FIXTURE- (i) The testing for leakage of pipe shall be done before connecting the pipes (ii) All pipes shall be minimum 4" away from walls fixed with GI bracket (iii) The gully trap shall be minim um 90 cm away from wall.(iv) Separate pipes for each floor should be provided (v) Sewage and drain system shall be separate.
Supply & fixing 75mm bore uPVC pipes grade 'B' single socketed in any length with rubber ring joints, fixed along walls/tranches with and including suitable size clamps/brackets (interval of 1m and pipe keeping 100mm away from wall ) of suitable size fixed with fasteners/nut bolts, joints fixed with pipe joint lubricant complete including bends, socket , Y junction, Tee , cowl etc all as specified and as directed by Engineer-in- charge complete including low carbon hot roll gauge corrected oil pickled & drawn pipe supporting clamping system 32x3mm with rib and notch are hot dip galvanised and Zn, Al flake coating with necessary clamps to fix and hold pipe complete all as specified and directed. (Note: Detail of Pipe supporting system is all as per Drg NO -BTD-916) Note:-UPVC PIPE AND FITTING/ FIXTURE- (i) The testing for leakage of pipe shall be done before connecting the pipes (ii) All pipes shall be minimum 4" away from walls fixed with GI bracket (iii) The gully trap shall be minim um 90 cm away from wall. (iv) Separate pipes for each floor should be provided (v) Sewage and drain system shall be separate
S&F 110 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by Engineer-in-Charge.
S&F 75 mm dia PVC SWR pipe, single socketed in any length with rubber ring joints fixed with clamps to walls complete all as specified and directed by Engineer-in-Charge.
S & F 110mm dia PVC (SWR) bends with access door opening complete all as specified and directed by Engineer-in-Charge.
S & F 110mm dia PVC (SWR) bends complete all as specified and directed by Engineer-in-Charge.
S & F 75 mm dia PVC (SWR) bends complete all as specified and directed by Engineer-in-Charge.
S&F stainless steel grating with or without hole 100 mm/125 mm dia (Min Wt 25 gms) complete all as specified and directed by Engineer-in-Charge.
S&F stainless steel grating square of size 150 mm with or without waste hole (Minimum weight 100gms) complete all as specified and directed by Engineer-in-Charge.
M&L PVC (SWR) gully trap 125/110mm, setting and jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.
S&F PVC (SWR) floor trap of 75 mm dia outlet plain with grating including jointing with solvent cement complete all as specified and directed by Engineer-in-Charge.
S&F PVC (SWR) 110 mm dia branch piece,single (single Y) equal or unequal complete all as specified and directed by Engineer-in-Charge.
S&F PVC (SWR) 110 mm dia junction (Single T) equal or unequal complete all as specified and directed by Engineer-in-Charge.
S& F PVC (SWR) 110 vent cowl complete all as specified and directed by Engineer-in-Charge.
M&L for precast cement concrete (1:2:4), type B1, using 20mm graded stone aggregate as in kerb stones size 300mm x 300mm x 100mm with plain fair faces, including chamfers, weathering, throating etc setting in CM (1:4) complete all as specified and as directed by Engineer-in-Charge.
M&L for 100mm thick PCC, (1:4:8), type D2, using 40mm graded stone aggregate as in sub base below floors complete all as specified and as directed by Engineer-in-Charge.
M&L Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks,lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand;n complete all as specified and as directed by Engineer-in-Charge.
M&L for PCC (1:3:6), type C1, using 20mm graded stone aggregate as in coping including necessary formwork, weatherig, slightly rounded or chamfered angle and throating complete all as specified and as directed by Engineer-in-Charge.
M&L for PCC (1:2:4), type B2, using 40mm graded stone aggregates as in benching / haunching of manholes including forming channels including necessary formwork etc complete all as specified and as directed by Engineer-in-Charge.
M&L precast cement concrete (1:2:4), type B1, using 20mm graded stone aggregate and set cement mortar (1:6) as in cover slabs (for manholes etc,) chajjas, shelves and similar articles with plain faces complete all as specified and as directed by Engineer-in-Charge.
Supply and laying DWCPE (SN8) 180 (OD)/163 (ID) mm diameter drain pipes as per IS-16098 (Part-II), laid in trenches on moorum bed to required slope, including all accessories/fittings, jointing and tested complete all as specified and as directed by Engineer-in-Charge
M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required etc for 150 mm bore complete all as specified and as directed by Engineer-in-Charge.
M&L for RCC Septic tank conventional type for 150 users designed to carry sewage and sullage water, excavation in any type of soil, PCC 1:4:8 below foundation, RCC M-30 Design mix in walls base slab, Baffle walls and roof slab including beam etc with vent shaft, manhole openings with cover conne tion etc, complete with effective depth of 1.5 meter and overall depth 3 meter for 150 users. Ref Drawing No. BTD-016 Sheet No-1/3, 2/3, &3/3 dated 16 Dec 2013
M&L for Size 1.8M dia X 4.5 M effective depth of soakage well excavation, in any type of soil, foundation in PCC 1:3:6, wall of honey combedmasonry with top ring of M-25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M-25 SFRC interconnecting pipe of RCC/DWC complete fillet with brick bats all as specified and directed. Ref Drawing No. BTD-804 Sheet No-1/1 dated 25 Aug 2011)
M & L for concealed conduit point wiring complete for light/ fan on independent /combine board with cable 2.5 sqmm (Nominal area) FRLSH PVC insulated multistranded unsheathed copper conductor, drawn in and including PVC Concealed conduit pipe medium grade 20 mm dia, pipe hooks , elbows, juction covers and junction boxes , after cutting in wall chasing for conduits and sinking's for modular metal flush boxes suitable length and Min 1.6 mm thickness, Min 51 mm depth for mounting, switches, sockets,fan regulator with modular cover plate with frame and making the good disturbed surfaces of wall in CM 1:3 with white wash or existing colour including provision of continuous earth continuity conductor along with point wiring of 2.5 sqmm copper PVC insulated cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.
All as per Srl item No -132 here in before but for One ceiling/exhaust fan point controlled by one switch and regulator complete all as specified and directed by Engineer-in-Charge.
All as per Srl item No -132 here in before but for One 3 pin switch socket outlet, 5 Amp on the same board with other switches complete all as specified and directed by Engineer-in-Charge.
All as per Srl item No -132 here in before but for One 3 pin 5 amps switch socket outlet point on independent board complete all as specified and directed by Engineer-in-Charge.
All as per Srl item No -132 here in before but for One bell/buzzer point controlled by one bell push complete all as specified and directed by Engineer-in-Charge.
All as per Srl item No -132 here in before but for Two way point controlled by two way switch complete all as specified and directed by Engineer-in-Charge.
All as per item Sl. No. 132 here in before but wiring with 4 sq.mm multistranded cable and earth wire with copper conductor of size 4 sq.mm for 15 amps power point complete all as specified and directed by Engineer-in-Charge.
S & F modular switch 5/6 Amps single pole one way,one module complete all as specified and directed by Engineer - in - Charge.
S & F modular switch 5/6 Amps single pole two way,one module complete all as specified and directed by Engineer - in - Charge.
S & F Modular switch 1 way 16A, with box complete all as specified and directed by Engineer - in - Charge.
S & F modular bell push switch 5/6 Amps single pole one way,one module complete all as specified and directed by Engineer - in - Charge.
S & F modular Socket, 6A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.
S & F modular Socket, 16A - 2/3 pin combined 2 Module complete all as specified and directed by Engineer - in - Charge.
S & F LED light fitting 1 x 20 W, 230 V integral sleek polycarbonate LED Channel with white acrylic cover incl making connection complete all as specified and directed by Engineer-in-Charge.
Supply and fix lamp holder insulated body with back plate for angle/batten fittiings alongwith 9 watt LED lamp complete all as specified and directed by Engineer-in-Charge.
Supply and fix bulk head 1x10 Watt fitting in die cast aluminium housing & frosted glass complete all as specified and directed by Engineer-in-Charge.
Supply and fix mirror light 1x10 watt fitting durable & weather proof industrial lighting solution luminaire with IP 65 protection complete all as specified and directed by Engineer-in-Charge.
Supply and fix ceiling rose surface bakelite two to three terminals/plate 5 amps complete all as specified and directed by Engineer-in-Charge.
Supply and fix sheet metal enclosure DB single pole and neutral for 240 volts 8 way with 200 Amps rated busbar flush/surface mounting double door including wooden board complete all as specified and directed by Engineer-in-Charge.
Supply and fix Vertical DB distribution box 3 phase TPN 4 ways double door including MCCB 125 Amp 16 KA as incommer with bus bar rating 200 Amps vertical type dust and vermin proof complete all as specified and directed by Engineer-in-Charge.
Supply and fix MCB single pole 240 volt 6-32 amps 10 KA, complete all as specified and directed by Engineer-in-Charge.
Supply and fix MCB SPN 240 volt 63 amp 10KA complete all as specified and directed by Engineer-in-Charge.
Supply and fix MCB TP 240 volt 63 amp 10KA complete all as specified and directed by Engineer-in-Charge.
Material & Labour for Sub Main Wiring with two run single core 6 Sqmm PVC insulated unsheathed (FRLSH) cable with stranded copper conductor drawn in PVC conduit & accessories Suitable size with and including 6 Sqmm copper green colour earth wire all as specified and directed by Engr-in-Charge. NOTE-two run of 6 sqmm & One run of 6 sq.mm & One run of PVC conduit with accessories shall be measured as One length.
Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6 mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level connected to GI wire 4mm dia by means of bolts, nuts, check nuts and washers complete including earthing pit, Chemical compound, GI wire 4mm dia up to 7.5 m, 20 mm dia medium grade GI watering pipe, G.I. protection pipe 40mm dia eath pit in PCC 1:2:4 type B-1 using 20 mm graded stone agggragate RCC pit cover including earth work complete all as shown electrical palte No-3 of SSR-2009 (Part-I) NOTE:- The unit rate shall include for excavation & earth work in any type of soil/strata, PCC 1:2:4 type B-I for pit & RCC 1:2:4 type B-I for cover with 8mm dia CTD Bar @150mm C/C both way, funnel with watering pipe 20 mm dia medium grade, 15mm dia light grade GI pipe up to 7.5 mtr long, wiremesh complete all as specified and directed.
S&F sheat metal incl single pole and neutal with 02 Pin and earth plug and socket complete with 01 single pole 20 Amps 240volts, MCB complete incl necessary fixing arrangement and all incoming and outgoing electric connection all as specified as directed by Engr-in-Charge.
S & F LED building security light fitting 45 watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover and accessories complete incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer complete all as specified and directed.
S & F LED building security light fitting 35 watt with epoxy powder coated sheet aluminium housing, with epoxy powder coated CRCA sheet steel grey tray, clear acrylic cover and accessories complete incl street light bracket made out of 25 mm dia GI medium grade pipe 0.6 mtr long complete with 2 sets of FI clamps made out of 30x5 MS flat & nuts, bolts & washer including painting to clamp with two coats of aluminium silver paint over a coat of primer after taking down old u/s one complete all as specified and as directed.
S/F modular fan step regulator 120W, 2 Module complete all as specified and directed by Engineer-in-Charge.
Supply and fix fresh air fan 230 mm sweep 240 vot 50 Hz plastic body complete with louvers complete all as specified and directed by Engineer-in-Charge.
Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. complete all as specified and directed by Engineer-in-Charge.
Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery . Five star rated with brushless direct current motor complete all as specified and directed by Engineer-in-Charge.
Supply and fix electric calling bell ding dong type , AC 230 Volt single pole incl making ielectric connection complete all as specified and directed by Engineer-in-Charge.
Supply and fix exhaust fan, steel body AC single Phase. 230V of size 300mm sweep with, blades, and frame and louvers complete all as specified and directed by Engineer-in-Charge.
Supply and fixing DWC pipe of size 77/63mm dia for protection of cable including all necessary excavation as specified and directed by Engr-in-charge
Supply, lay and testing of cable LT XLPE insulated screened PVC bedded, galvanised steel strip or wire armoured, electric power cable heavy duty with stranded aluminum conductor, 440 Volts grade, of size 25 sqmm 4 core including making necessary electrical connections by using Al thimbles of applropriate size complete all as specified and directed by Engr-In-Charge Note:-Excavation, earthwork, will be measured and paid separately under respective items of this Schedule.
M&L for G.I. water tubing, medium grade, 50mm dia with all fitting and fixed complete laid in trench complete all as specified and directed by Engineer-in-Charge.
M&L for G.I. water tubing, medium grade, 25mm dia with all fitting and fixed complete laid in trench complete all as specified and directed by Engineer-in-Charge.
M&L for G.I. water tubing, medium grade, 20mm dia with all fitting and fixed complete laid on wall complete all as specified and directed by Engineer-in-Charge.
M&L for Gun metal, glove or gate valves of 50mm dia with iron wheel head screwed both ends for iron pipe complete all as specified and directed by Engineer-in-Charge.
M&L for Tee/Ferrule branch connection of size 25mm dia from 200mm dia existing pipeline all as specified and directed by Engineer in Charge.
Please Enable Macros to View BoQ information
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Tendernotice_1.pdf
PDF • 0.37 MB
BOQ_835783.xls
BOQ • 0.40 MB
Tender_101.pdf
Tender Documents • 1.18 MB
Download all tender documents and submit your bid