REPAIRS/REPLACEMENT OF ROOF, JOINERY, PLASTERING, PLUMBING AND CONNECTED WORKS AT 162 MH AND REPAIRS/REPLACEMENT OF FOOTPATH, CULVERT, COMPOUND WALL AND FENCING AT DINJAN MIL STATION UNDER GE DINJAN

Amount

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in soft/loose soil complete all as specified and as directed.

Returning, filling in including spreading in layersnot exceeding 25cm, levelling, watering and well ramming as in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and as directed.

Excavating in post holes (or similar holes) each not exceeding 0.50 cum in soft soil/loose soil and getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance not exceeding 50 m and making good surfacecomplete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed

Demolition of unreinforced cement concrete in ground floors and pavings not exceeding 15 cm thick (below or above ground level) complete all as specified and directed

Demolition of brickwork or stone/ boulder masonry, built in Cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlars facings, dressed stonework and precast concrete articles complete all as specified and as directed

Dismantling asbestos cement (corrugated or semi corrugated) sheet in roof covering complete all as specified and as directed.

Dismantling posts or struts (wood, steel or RCC) any section embedded in concrete, brick work, masonry etc, including taking out embedded portion concrete, brick work, masonry work, etc and making good disturbed ground complete all as specified and as directed.

Dismantling fencing wiremesh, any type, any size complete all as specified and as directed.

Taking down the chowkhats or frames not exceeding 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the chowkhats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frames) complete all as specified and as directed

Taking down the shutters of any description not exceeding 1.00 Sqm each complete all as specified and as directed

Taking down the shutters of any description exceeding 1.00 Sqm and not exceeding 2.00 Sqm each complete all as specified and as directed

Taking down shutters of any descrption not exceeding 1.00 Sqm each and refixing in the same opening complete all as specified and directed.

Taking down shutters of any description exceeding 1.00 Sqm but not exceeding 2.00 Sqm each and refixing in the same opening complete all as specified and as directed

M&L for hardcore of broken stone or boulders guage not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and as directed.

M&L for PCC (1:4:8) type D2 (using 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PCC (1:2:4) type B2 (using 40 mm graded aggregate) as in foundation, filling and mass concrete complete all as specified and as directed.

M&L for PCC in (1:2:4) type B0 ( using 12.5 mm graded aggregate) as in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for PCC (1:3:6) type C2 (using 40 mm graded aggregate) as in surface channels and drains complete all as specified and as directed.

M&L for precast cement concrete (1:2:4), type B1, (using 20 mm graded aggregate) as in landings, cover slabs and similar articles with plain faces set in cement mortar (1:4) complete all as specified and as directed

M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for brick work with sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar in (1:4) complete all as specified and as directed

M&L for second class hardwood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed complete all as specified and as directed.

M&L for 35 mm thick second class hardwood plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F 30mm thick, glazed/skelton shutters with second class hard wood,open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, sizes of members of shutter as specified in SSR Part I Section 8, clause 8.24 (b) complete as specified and directed.

S&F 35mm thick, glazed/skelton shutters with second class hard wood, open rebated and prepared to receive glass, gauge, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc, sizes of members of shutter as specified in SSR Part I Section 8, clause 8.24 (a) complete as specified and directed.

S&F for factory made solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed

S&F for factory made solid panel PVC door shutter, 30 mm thick (style) consisting of frame, made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing in SSR Part II 2010 complete all as specified and as directed

M&L for 18/19mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work and fixed with wooden beading complete all as specified and as directed

M&L for PCC (1:2:4) type B0 (using 12.5 mm graded aggregate) as in hold fast and filling of steel chowkhat etc. complete all as specified and directed

S&F for mild steel flat iron as in hold fast 25x6 mm confirming to Fe290 (Gde E-165) complete all as specified and directed

S&F for 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F in repairs, 300 mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

S&F in repairs aluminium anodised barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

S&F in repairs aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F aluminium anodised barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

S&F for aluminium anodised barrel tower bolts of extruded section 150 mm long complete all as specified and directed.

S&F in repair 75 mm long, butt hinges, medium weight, cold rolled mild steel fixed to chowkats complete all as specified and directed

S&F in repair 100 mm long, butt hinges, medium weight, cold rolled mild steel fixed to chowkats complete all as specified and directed

S&F for 75 mm long, butt hinges, medium weight, cold rolled mild steel fixed to chowkats complete all as specified and directed

S&F for 100mm long butt hinges, medium weight, cold rolled mild steel fixed to chowkats complete all as specified and directed

S&F in repairs aluminium handle 100 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F in repairs aluminium handle 150 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F aluminium handle 100 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F aluminium handle 150 mm long cast type, anodised extruded fabricated type complete all as specified and as directed.

S&F in repairs harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. complete all as specified and as directed.

M&L for double action floor spring, hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet, foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed complete all as specified and as directed.

S&F for joist, channel, angle, or tee sections of Fe 290 (Gde E-165) fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and as directed.

S&F for mild steel angle posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting or riveting etc and similar work conforming to Fe-290 (Gde E-165) complete all as specified and as directed.

Supply only chain link mild steel galvanised fencing any size or type 4 mm dia galvanized wire (100x100) mm mesh made upto matress lapped wire and laid on position / fixed on poles complete all as specified and as directed.

Fixing only chain link fencing incl line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc including provision of binding wire complete all as specified and as directed.

S&F for galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

M&L for mild steel round bars of Fe 290 (Gde -E-165) 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F for mild steel screw bolts of 11 to 15mm dia of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt not exceeding 5cm long complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

M&L for 6mm thick asbestos cement corrugated or semi-corrugate sheets in roofs, walls, etc fixed with L or J-type or cranked hook bolts complete all as specified and as directed.

M&L for asbestos cement two piece adjustable plain wing ridge 6mm thick fixed with L-type or J-type or cranked hook bolts complete all as specified and as directed.

M&L for coloured glazed ceramic tiles in vertical surface 300x200x7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 10mm thick plastering in CM (1:4) as a backing coat complete all as specified and directed.

M&L for coloured glazed ceramic tiles in vertical surface of size 450X 350X 7 mm thick over 10 mm thick back coat of cement mortar in (1:4) set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed or bedding layer of cement mortar in (1:6) for laying floor finishes complete all as specified and as directed

M&L for light shade vitrified ceramic tiles 10 mm thick (square /rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed in cement mortar (1:6) complete all as specified and directed.

M&L for light shade vitrified ceramic tiles 10 mm thick (Square.rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backcoat in cement mortar (1:4) complete all as specified and directed.

M&L for chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc, including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking paver block, design & shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment including 75 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. complete all as specified and as directed.

M&L for 20 mm thick granite (of any type) work (table rubbled and polished) in steps, Jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed

Renewing tiles in patches, area not exceeding 5 sq.m. including removing and cleaning old tiles, preparing beds and laying or setting, jointing and pointing new or old tiles complete all as specified and directed

M&L for 75 mm thick plain cement concrete (1:3:6), type C2, (using 40mm graded aggregate) in plinth protection, finishing cement concrete surface even and smooth without using extra cement complete all as specified and as directed

M&L for 100 mm thick plain cement concrete (1:4:8) type D2 (using 40 mm graded stone aggregate) as in sub base of floor, etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M&L for rendering 15 mm thick on fair faces of external wall of brick work or stone surfaces in two layers (10 mm and 5 mm thick) in cement mortar (1:4) using water proofing compound in top layer (water proofing compound measured separately) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick of internal wall on fair faces of brick work or concrete surfaces in cement mortar in (1:6) and finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on ceiling in cement mortar (1:3) finished even & smooth without using extra cement complete all as specified and directed

Supply only Liquid water proofing compound complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces of walls by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old decorated plastered surfaces of ceiling by brooming down or steel wire brushing, scraping down with steel scraper, smoke soot, moulds moss and efflorescent salts, trading oil and greasy spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparing old plastered surfaces of walls by washing, rubbing down and scraping of existing distempering/painted surfaces etc and applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for complete removal of existing treatment of walls surface and applying two coats of distemper oil emulsion white or tinted over chalk whitening complete all as specified and as directed.

M&L for preparation of old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moos, efflorescent, having oil and greases spots and applying one coat of cement base paint (white or tinted) complete all as specified and as directed

M&L for preparation of old decorated plastered or unplastered surfaces of wall cornices etc by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moos, efflorescent, having oil and greases spots and applying two coats of cement base paint (white or tinted) complete all as specified and as directed.

M&L for one coat of 3mm thick wall care putty on wall complete all as specified and as directed.

M&L for preparation newly or old decorated external surfaces of wall, chajja, facia etc by complete removing old paints by hand scrubber without disturbing the plastered surfaces broomed to remove all dust, dirt and all loose scales of old paints and other foregin materials and applying one coats of water based acrylic weather proof exterior emulsion (Apex ultima superior quality) paint complete all as specified and as directed.

M&L for preparation of new plastered surface of walls etc and applying two coats of cement base paint over alkali resistant priming paint including complete all as specified and directed

M&L for preparation of new plastered surface of walls etc and applying two coats of distempering interior walls with distemper oil emulsion white or tinted over a coat chalk whiting complete all as specified and directed

M&L for preparation of new plastered surface of walls etc and applying three coats of white wash complete all as specified and directed

M&L for preparation of new plastered surface of ceiling etc and applying three coats of white wash complete all as specified and directed

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and as directed.

S&F for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 3 mm thick figured glass, pin head type and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for 5.5 mm thick sheet glass, ordinary quality and glazing with oil putty in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

M&L for preparation of old painted surfaces of wooden surface of any description, not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed.

M&L for preparation of new or untreated surfaces of wooden surface of any description, not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over pink primer complete all as specified and as directed.

M&L for preparation of old painted surfaces of steel and iron surfaces of any description, over 10cm in width or girth, not otherwise described, applying one coat of synthetic enamel paint complete all as specified and directed

M&L for preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of zinc chrome red oxide primer complete all as specified and as directed.

Dismantling of water tank capacity exceeding 250 not exceeding 500 Ltrs and removing to store complete all as specified and as directed

Dismantling of water tank Capacity exceeding 500 not exceeding 1000 Ltrs and removing to store complete all as specified and as directed

S&F for 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

S&F for 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks exceeding 250 liter not exceeding 500 liter and from mouths of circulating pipes, etc. complete all as specified and as directed.

Cleaning and removing all scale and dirt, etc, from tanks exceeding 500 liter not exceeding 1000 liter and from mouths of circulating pipes, etc. complete all as specified and as directed.

S&F for 20 mm bore, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs 20 mm bore, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and as directed.

S&F in repairs white vitreous china squatting pan Orissa pattern of size 580mmx440 mm white, with integral foot rests connected with 'P' or 'S' trap and flushing pipe and taking out old WC & connections complete all as specified and as directed.

S&F in repair vitreous china wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and as directed.

S&F for plastic water closet seat, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F in repairs for PVC connections 15mm size with PTMT nuts of length 600 mm complete all as specified and as directed

S&F in repairs PVC low level flushing cistern, 10 litre capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC conection pipe and flush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified and directed

S&F in repairs vitreous china bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and as directed.

S&F in repair for tubular towel rail, 20mm dia, D type, 60cm long brass chromium plated between flanges complete all as specified and as directed

S&F in repairs soap dish vitreous china coloured approximate size (160mmx160mmx90mm) complete all as specified and as directed.

S&F in repairs vitreous china wash hand basin white flat back size 550x400mm excluding taps, waste chain and plug and porcelain stopper including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and as directed.

S&F in repairs 15 mm bore dia cast copper alloy fancy type, chromium plated stop valves, crewed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 20 mm bore dia cast copper alloy fancy type, chromium plated stop valves, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 15mm stop valves (concealed type), cast copper alloy fancy type chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repairs 20mm stop valves (concealed type), fancy type chromium plated, long sunk and cup, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S&F in repair pillar taps of size 15mm, chromium plated, fancy type, cast copper alloy, with capstan heads, screwed down high pressure, with or without lettered 'Hot' or cold with long screwed shanks and fly nuts screwed for iron pipe complete all as specified and as directed.

S&F in repairs for bib taps, fancy type, chromium plated with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferule and fixed of size 15mm bore in repair complete all as specified and as directed.

S&F for brass chromium plated shower rose, 125 mm size fixing to steel pipe or union complete all as specified and as directed

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and as directed

S&F 15 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F 20 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F in repairs toilet paper holder of vitreous china fixed to walls with chromium plated brass screws complete all as specified and as directed

M&L for PVC (SWR) floor trap, 75mm dia, plain with grating including jointing with solvent cement including disconnection of old existing trap, and connected with existing water pipe complete all as specified and directed.

S&F for grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F for 375 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed

M&L for cutting chases, pinning in brick walls, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 20 cm girth complete all as specified and as directed.

S&F in repairs110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and as directed.

S&F in repairs 75 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) branch piece, double (double Y) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 75mm bore PVC (SWR) junction single, (Single T) equal or unequal complete all as specified and as directed.

S&F for 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F for 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F in repairs 32 mm Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm?45gms/40mm-60 gms)complete all as specified and as directed.

S&F in repairs 40 mm Waste coupling of PTMT (half or full threaded) (Minimum weight 32mm?45gms/40mm-60 gmscomplete all as specified and as directed.

S&F in repair health faucet cast copper alloy with push button & 1m long flexible steel pipe with PVC lining suitable for 15mm bore pipe complete all as specified and directed.

S&F 15mm dia angular stop cock with wall flange all as specified and directed.

Supply and fixed PVC waste pipe of 32 mm size flexible and 1.2 mtr long, fitted to basin or sink complete all as specified and as directed.

M&L for reinforced concrete pipes, class NP2, 600 mm bore, laid and jointed with collars complete all as specified and as directed.

M&L for reinforced concrete pipes, class NP2, 300 mm bore, laid and jointed with collars complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 600 mm bore drain pipes complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2 (using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete for 300 mm bore drain pipes complete all as specified and as directed.

M/S CHANDAN ENTERPRISE

MAZUMDAR ENTERPRISE

M/S Karen Enterprises

M/S BORAH BROTHERS

Garg Brothers

M H KHAN

M/S A K BROTHERS