REPAIR/REPLACEMENT OF JOINERY, ROOF, WATER SUPPLY AND PLUMBING WORKS INCLUDING CERTAIN SANITARY FITTINGS AND OTHER MISC AND ALLIED WORKS IN OTM AND MD ACCN AT NAPIER ROAD UNDER GE (CENTRAL) KOLKATA

Amount

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

Demolition of cement concrete(un-reinforced) in ground floors and pavings not exc. 15 cm thickness below or above ground level. complete all as specified and as directed.

Dismantling Timber Scantlings, 40 Sqcm and over in Section, in any Position, in Unframed Work, complete all as specified and as directed.

Dismantling Timber Fillets, Rails, Posts, Rafters, Purlings, etc., under 40 Sqcm in Section, in any Position, as in framed Work, complete all as specified and as directed.

Taking down Chowkats or Frames, (without taking off Shutter from the Frame) exc. 1.50 Sqm but not exc. 4.00 Sqm Each, complete all as specified and as directed.

Taking down Chowkat or Frame (without taking off Shutter from the Frame) n exc. 1.50 Sqm complete all as specified and as directed.

Taking down Shutters of any description, not exc. 1.00 Sqm Each complete all as specified and as directed.

Taking down Shutters of any description, exc. 1.00 Sqm but not exc 2.00 Sqm Each complete all as specified and as directed.

Dismantling Wrought Iron or Mild Steel Work, viz. MS Flat Iron (Wind Tie) , grill guard bar and Similar Work including MS Bolts, Nuts, etc., complete all as specified and as directed.

Dismantling AC Corrugated Sheets as in Roofing including Ridge or Similar Pattern Roof Coverings, complete all as specified and as directed.

Dismantling Plain or Corrugated Steel Sheeting any gauge, thickness, including nainital or similar roof coverings/sunshade, complete all as specified and as directed.

Dismantling of Wall and Ceiling Board (Fibre, Pulp, Insulation etc.) or Insulation Board/Slab /Blankets, any thickness including Cover Fillets, complete all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including Cement Mortar Bedding (but not backing), and removing rubbish off the Premises, complete all as specified and as directed.

Taking down Cement Plaster of any description on Brick Walls, Concrete Surfaces including racking out joints, hacking for key, scrubbing down with Water, remove dust, debries/ rubbish, etc., complete all as specified and as directed.

Taking up or down Steel Water Tubing 15mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removal to store complete all as specified and as directed.

Taking up or down Steel Water Tubing 20mm dia (bore) including Connections and Fittings, Segregating Serviceable Pipes & Fittings, Stacking properly at Site(s) and keep in Safe Custody for re-use or removal to store complete all as specified and as directed.

Taking down unserviceable PVC (SWR) Pipes & Fittings of any size or pattern and in any Position (Measured overall as fixed along the Centre Line over the Fittings and Accessories), complete all as specified and as directed.

M&L Cement Concrete Type B1,1:2:4 (40 mm graded crushed stone aggregate) as in Holdfast Block including necessary form-work, etc., complete all as specified and as directed.

M&L Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in Cement Mortar 1:6, complete all as specified and as directed.

Labour only Brick Work using old bricks obtained from demolition, Straight or Curved on Plan exc. 6.0 Metre mean Radius, built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick Work pulverizes fly ash bricks ,Half-Brick thick, Old Size, built in Cement Mortar 1:4, Straight or Curved on Plan to any Radius, complete all as specified and as directed.

M&L Second Class Hardwood in Scantlings wrought Timber Framed work and fixed complete all as specified and as directed.

Fixing only Second Class Hardwood in Scantlings wrought Timber Framed work and fixed complete all as specified and as directed. Note-Existing Timber shall be reused, obtain from dismantling item here-in-before.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section wrought, secured with Nails, cross sectional area exc 6.0 Sqcm but not exc. 13.0 Sqcm complete all as specified and as directed.

M&L Second Class Hardwood Plain Fillets sqaure, rectangular or triangular in section wrought, secured with Nails, cross sectional area exc13.0 Sqcm but not exc. 25.0 Sqcm complete all as specified and as directed.

S&F Second Class Hardwood Plain, Solid, Straight Chowkats and Frames, Wrought, Framed rebated on the Solid, Rounded or Chamfered, put together with Glue, Pinned at Joints, complete all as specified and as directed.

M&L Factory made 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated, complete all as specified and as directed.

S&F Flush Shutters 30 mm thick, Solid Core Construction with Block Board Core and Plywood Face Panels, Commercial type on Both Sides, complete all as specified and as directed.

M&L 35mm thick glazed and skelton shutters, open rebated and prepared to receive glass , gauge, etc (without sash bars) , edges of framing plain, chamfered of rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkhats complete all as specified and as directed.

M&L 35mm thick glazed and skelton shutters, open rebated and prepared to receive glass , gauge, etc (with sash bars) , edges of framing plain, chamfered of rounded fitted with cut and mitred beads for securing glass, etc sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) supplied and fitted to chowkhats complete all as specified and as directed.

S&F Factory Made Solid PVC Door Frame of size 50 x 47 mm made out of 5.0 mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F Plain Colour Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing etc complete all as specified and as directed.

S&F Solid PVC Wall Lining consisting of 5mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5 mm thick PVC sheet fillet of width 35mm for wall Paneling inclusive of fixing on to wall to make PVC Frame as per specification and drawing including taking down old unserviceable PVC wall lining complete all as specified and as directed.

M&L Mild Steel Flat Iron 25 x 3 mm, as in Holdfast for Door, Window Frames or Chowkats etc., Wind Ties for Roof including securing bolts cut to length or drilled hole and fixed with Screw, etc., grade of Steel conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L Framed Work such as Grills, Gratings, etc. with ends of Bars shouldered and/or riveted, or forged into Spikes; Framed Guard Bars; Barred Iron Doors; Ladders; Framed Balusters; Walk Ways; Railings; Framework of Water Tanks and Similar Work, conforming to Fe-290, Gde-E-165, complete all as specified and as directed.

S&F Roof trusses (framed) , trussed , purlines, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, channel or Flat section) including distance pieces , cleats etc Fe-410W (Gde E-250 Quality `A' complete all as specifed and directed.

S&F Steel rolling shutter with thickness of latch 1.25mm without ball bearing as specified including top cover anchoring rod, hasp & staple and one shop coat of primer , erected in position , push pull of manual type including taking down old one complete all as specified and as directed.

S&F Safety lever locks mild steel with 4 levers for rolling shutters as in repair complete all as specified and as directed.

S&F Ball bearing for rolling shutters as in repair complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter n exc 7 Sqm complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter exc 7 Sqm but n exc 12 sqm complete all as specified and as directed.

Overhauling and greasing of rolling shutter of any size and pattern including scrubbing down old greasing for proper functioning, area of each shutter exc 12 Sqm but n exc 18 sqm complete all as specified and as directed.

S&F MS locking plate of standard size and shape from approved quality with a coat of red oxide primer including taking down of old one complete all as specified and as directed.

S&F Rolling shutter profile of 1.00mm thick MS sheet with a coat of red oxide primer (shope coat) minimum width of profile 75mm including taking down old one complete all as specified and as directed.

S&F Spring of rolling shutter of approved quality and size including taking down of old one complete all as specified and as directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, made of Z section 100mm long and steel peg stay, complete with glazing bars, dovetailed or welded including one shop coat of red oxide zinc crome primer, complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, made of Z section 100mm long and steel peg stay, complete without glazing bars, dovetailed or welded including one shop coat of red oxide zinc crome primer, complete all as specified and directed.

S&F Steel windows or ventilators, fixed type, with glazing bars dovetailed or welded including one shop coat of red oxide zinc crome primer, complete all as specified and directed.

M&L False ceiling with 'E' board "Classic" , reinforced, designer series, board with HPSC of size 600 mm x 600 mm x 4 mm thick fixed on aluminium powder coated snap grid to support the boards/tiles with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 6mm dia GI hooks and clamp and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

S&F Mild steel tubes 40 mm bore (Medium Graded) with all fittings & fixed to walls and ceiling for holding clamps of false ceiling as in repair complete all as specified and as directed.

S&F Aluminium door with powder coated anodized aluminium frame of section size 101.60 mm x 44.75 mm x 2.4 mm (jindal section 14021) thick, with shutter of style member size of 85mm x 44.45 x 2.00mm thick (Jindal section 19560), Top/bottom rail of member size 114.30mm x 44.45 x 2.15mm (Jindal section 19574) and lock rail of member size 100mm x 44.45mm x 2.0mm thick (jindal section 19564) with rubber gasket and aluminium glazing clip beading and 100mm mortice locking arrangement ,handle, tower bolt 200mm long per shutter, rollers, etc complete all as specified and directed.

S&F Aluminium anodised Three track sliding window frame with shutters including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements etc. complete and glazing with 5 mm thick tinted glass to aluminium frame work using rubber gasket where the section of frame and shutter as in repair complete all as specfied and directed as under :-(A) Sections for frame (i) Top and verticals 92x 29.50 x 1.30 mm thick (ii) Bottom 92 x 29.50 x 1.20 mm thick. (B) Sections for shutter (i) 'A' section 39 x 20 x 1.50 mm thick (ii) 'Interlock' section 39 x 20 x 1.50 mm thick (iii) 'H' section 41 x 20 x 1.10 mm thick Note: Glazing shall be measured and paid separately. Make: Jindal or equivalent sections of Hindalco.

S&F Aluminium ventilator with powder coated anodized aluminium frame of section size 65.5 x 38.10 x 1.5 mm and Shutter with section 47.62mm x 44.5mm x 1.5mm thick half portion fixed with glass and half portion louvered including powder coated alunimium anodised “D” handle, hinges, peg stays, tower bolt etc including jointing cleats for fixing Builder hardware complete all as specified & directed.

M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass,other parts made of mild steel heavy duty and fixed etc as in repair complete all as specified and directed.

S&F Floor door stopper of steel body and overall length of cover plate 75 mm and tongue anodised with hard drawn steel spring as in repair complete all as specified and directed.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples complete all as specified and as directed. NOTE: Cost of Second Class Hardwood Bead-ing shall deemed to be included against Glazed and Skeleton Shutter.

S&F Stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.40mm and fixed with Stainless Steel Wire Staples as in repair complete all as specified and as directed. NOTE: Cost of Second Class Hardwood Bead-ing shall deemed to be included in the BOQ

S&F Aluminium alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, complete all as specified and as directed.

S&F Aluminium alloy Handle 150mm long, Extruded Section, Fabricated type, anodized and fixed, as in repair complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 200mm long, Extruded Section and fixed, as in repair complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 150mm long, Extruded Section and fixed, complete all as specified and as directed.

S&F Aluminium anodized, Barrel Tower Bolt 150mm long, Extruded Section and fixed, as in repair complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, complete all as specified and as directed.

S&F 300mm long Aluminium alloy, anodised, Sliding Door Bolt with Hasp, Staple (Bolt type) and Fixing Clips of Sheet, Cast or Extruded Sections and Fixing Bolts and Sliding Bolts of Extruded Sections or Cast-Aluminium alloy and fixed, as in repair complete all as specified and as directed.

S&F Stainless Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, complete all as specified and as directed

S&F Mild Steel Butt Hinges, size of Hinges 100mm, medium weight, Cold Rolled and fixed, as in repair complete all as specified and as directed.

S&F Stainless steel Continuous (Piano) Hinges, width of Flaps (when open) 40mm, bright finish and fixed, as in repair complete all as specified and as directed.

M&L Prelaminated Particle Board 19/20 mm thick, interior grade, double leaf pre-laminated one side with decorative choice lamination and other side balancing white lamination fixed with Screws to Timber Frame Work as in cup board shelf/shutter ,Pelmet Box or in narrow widths not exc. 15 Cm each, rebated or flat edged, properly sealed with 5 mm thick 2nd class hard wood beading fixed with water resistant adhesive except rebate side as in repair complete all as specified and as directed.

S&F Asbestos Cement Corrugated Semi-Corrugated Sheets 6.0mm thick as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

Fixing only old serviceable Asbestos Cement Corrugated,Semi-Corrugated Sheets 6.0mm thickheets obtained from dismantling item as in Roof Covering fixed with L–type or J–type Cranked Hook Bolts with Washers, etc. and fixed, complete all as specified and as directed.

S&F Pre-painted colour galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F Pre-painted colour galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall /sunshade etc, fixed with self tapping screws complete all as specified and as directed. Note :- Existing Galvalume sheet shall be reused, obtain from dismantling item here-in-before.

S & F 0.80 mm thick plain, galvanised, mild steel sheeting in ridges, hips, valley gutters, drip and straight flashings(length and girth as fixed) with grade of zinc coating 120complete all as specified and as directed.

M&L Cement Concrete type C2(1:3:6) using 40mm graded crushed stone aggregate 75mm thick as in Plinth Protection, etc. laid in alternate Bays, finished Concrete Surfaces Even and Smooth without using Extra Cement, complete all as specified and as directed.

M&L Cement Concrete type B1(1:2:4) (20mm graded crushed stone aggregate) 40 mm thick as in Floor, finishing Concrete Surfaces Even and fair without using Extra Cement, complete all as specified and as directed.

M&L Prepolished cement concrete chequered tiles of size 400 x 400 x 20 to 25 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including 20mm thick screed bed in cement mortar 1:6 for laying floor finishes and including dismantling of chequered tiles . complete all as specified and directed.

M&L Coloured vitrified ceramic floor tiles10 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc. 0.36 sqm (600mm x 600mm x 10mm) as in floor etc, set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor make incl 15 mm thick screed bed or bedding of layers in CM 1:6 complete all as specified and as directed.

M&L Coloured vitrified ceramic tiles10 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n. exc. 0.36 sqm (600mm x 600mm x 10mm) on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm in Floors, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 15mm thick screed bed (1:6) in cement mortar complete all as specified and as directed.

M&L Non-skid Ceramic Coloured Tiles, 7.0mm to 8.0mm thick (square/rectangular), area of each tile exc 0.11 sqm but not exc 0.18 sqm on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Glazed Ceramic Coloured 450 x 350 x 7.0mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges,including dismantling of stone slabs and tiles of any description or thickness complete all as specified and as directed.

M&L Rendering 20mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 10mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed.

M&L Rendering 5.0mm thick in Cement Mortar 1:3 on Concrete Surfaces of Ceiling, etc. finishing Plastered Surfaces Even and Smooth, without using Extra Cement. complete all as specified and as directed.

"Supply only" liquid water proofing compound (ISI marked) complete all as specified and directed.

M&L Preparing new plastered surfaces of walls and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 2mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new plastered surfaces of ceiling and applying Two Coats of Distemper Oil Emulsion over a coat of primer and applied over 2mm thick BIRLA/JK water proof wall care putty including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed.

M&L Preparing new plastered surfaces of Walls and applying Two Coats of Exterior Emulsion Paint Weather Coat over a coat of alklai resistance Primer (as per Manufacturer’s instructions), complete all as specified and directed.

S&F 4.00 mm thick tinted glass, ordinary quality and glazing with aluminium/wooden beading in square n. exceeding 0.5 sqm in each pane fixed complete all as specified and as directed.

S&F 5.5mm thick tinted glass, ordinary quality and glazing with aluminium/wooden beading in square exceeding 0.5 sqm in each pane fixed complete all as specified and as directed.

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, n exc 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide/ Zinc Chrome Primer, complete all as specified and as directed.

Supply and Laying Steel Water Tubing 15mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

Relaying/Re-fixing Galvanised Steel Tubing 15mm Bore (dia) and Connections in New or Old Position (Serviceable Pipes and Fittings obtained from dismantling here-in-before) after Cleaning both Inner and Outer Surfaces of Pipes by using of Wire Brush including Provision of New GI Fittings (as ordered), complete all as specified and as directed.

Relaying/Re-fixing Galvanised Steel Tubing 20mm Bore (dia) and Connections in New or Old Position (Serviceable Pipes and Fittings obtained from dismantling item here-in-before) after Cleaning both Inner and Outer Surfaces of Pipes by using of Wire Brush including Provision of New GI Fittings (as ordered), complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F Stainless Steel Sink with Drainage Board l.0mm thick Overall size 915mm x 460mm and Bowl size 410 mm x 330 mm x 160 mm for Kitchen or Laboratory with Plugs, Washers, Brass chromium plated Waste Fitting 32mm dia, PVC waste pipe, a Pair of Cast Iron Brackets duly Painted including Cutting and Pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including Taking down/out unserviceable Sink and connected Items, complete all as specified and as directed. Make : Prayag Cat Part No. 939D or equivalent in Nirali / Hindustan/ Neelkant .

S&F 32mm dia PVC flush pipe of low or high density polyethylene pipe fixed to low level flush cistern including all necessary fixing arrangement as in repair complete all as specified and directed. Make : Prayag or equivalent make as specified in Particular specifications.

S&F PVC (SWR) Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, ceilings and floors with pvc clamps complete all as specified and as directed.

S&F PVC (SWR) Pipe 110mm bore (dia), double socketed, in any length with Rubber Ring Joints fixed to Walls, ceilings and floors with pvc clamps complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any type, . and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Junction 75mm bore (dia), Single (Single T) equal or unequal and Jointing with Solvent Cement, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, 32mm dia Chromium Plated bottle trap and 15mm dia PVC connector pipe, a pair of Cast Iron Brackets duly painted Stand including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 complete all as specified and as directed. Make - Parryware Model No-C0406(SP)/C0434(CTH) or equivalent make as specified in the particular specfication.

S&F 10 litre capacity low level PVC flushing cistern (any colour), syphonic action type, with inlet, ball valve, float, handle, fixed with cast iron bracket (of suitable size) and providing 32 mm dia PVC flush pipe and making all necessary connections including taking down/out unserviceable one complete all as specified and as directed. Make : Cera cat part No CONGO B1010109/ Parryware Model No- E-8090 or equivalent model as specified in Particular Specification here in after.

Supply and fix in repairs Vitreous China squatting pan of ‘Orissa pattern’, size 580 mm x 440mm (white) with ‘P’ or ‘S’ trap, front or back inlet and foot rests, any pattern complete including provision of PCC bedding and connection to trap, and to flushing pipe, antisyphonage pipe, etc. complete including making good to floor complete all as specified and directed. Make - Parryware Model No-C0297, or equivalent make specified in the particular specification

S&F PTMT Ball Valve 20mm dia having mini -mum weight 210 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed as in repair, complete all as specified and as directed. Make : Prayag, Cat No 151 or equivalent model as specified in list of approved makes given here in after in Particuler Specification.

S&F PTMT Ball Valve 25mm dia having mini -mum weight 455 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed, as in repair complete all as specified and as directed. Make : Prayag, Cat No 153 or equivalent model as specified in list of approved makes given here in after in Particuler Specification.

S&F Glass shelf assembly consisting of 5.5 mm thick sheet glass self 19-12 cm wide, 60 cm long with chromium plated brackets guard and railing fixed in position with necessary fixing arrangement as in repair complete all as specified and directed. Make:- Prayag or equivalent make as specified in Particular Specification here in after.

S&F PTMT Grating Doom of 100mm size (Min weight 25 grms) and fixed-in-repairs, complete all as specified and as directed.

S&F 125 mm dia brass chromium plated shower rose with or without swivels joint for fixing to 15 mm bore pipe etc complete including taking down old one complete all as specified and directed. Make:- Essco Cat pat No EOS-541N or equivalent make as specified in the particular specfication.

S&F Chromium plated Bib taps for 15 mm bore of pipe incl necessary fittings & fixtures as in repair complete all as specified & directed Make : Essco (DLX-511 or equivalent make specified in the particular specification

S&F Chromium Plated soap dish incl necessary fittings & fixtures as in repair complete all as specified & directed. (Make:- Jaguar CAN-1151N) or equivalent make specified in the particular specification.

S&F Brass chromium plated Pillar Tap screwed for 15 mm bore pipe incl necessary fittings & fixtures as in repair complete all as specified & directed. Make : Essco (DLX-507) or equivalent make specified in the particular specification

S&F Brass chromium plated fancy type stop cock screwed for 15 mm bore of pipe etc.incl necessary fittings & fixtures as in repair complete all as specified & directed. Make:- Essco Cat pat No DLX 513B or equivalent make as specified in the particular specfication.

S&F PVC bathroom cabinet (white) of size 430 x 330 x 100 mm (approx) with one single shutter and built in mirror in front of shutter, fixed on walls with wooden plugs and and chromium plated brass screw and cup washe as in repair complete all as specified & directed. Make -Prayag or equivalent make as specified in Particular Specification here in after.

S&F Cascade type (coloured) floor mounted water closet with low level flushing cistern coloured with floor trap, PVC coloured seat cover and connecting pipe etc and making all necessary connections etc as in repair complete all as specified and as directed. Make : Parryware Aquarius, Code No. C-0235, C-0715 C-2016, C-8080 & C-8071 or equivalent make as specified in Particular Specification here in after.

S&F Bib tap with nozzle 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight15mm-95 gms) as in repair complete all as specified and directed. Make : Prayag (Cat No. 121) or equivalent make as specified in Particular specifications.

S&F Pillar taps fancy type15mm bore of PTMT any colour screwed for iron pipe & fixed. (min weight 15mm- 110 gms) as in repair complete all as specified and directed Make : Prayag (Cat No. 142) or equivalent make as specified in Particular specifications.

S&F Stop valve 15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-90gms) with PTMT flange as in repair complete all as specified and directed. Make : Prayag (Cat No. 142H) or equivalent make as specified in Particular specifications.

S&F PVC connection pipe 15mm size with PTMT nuts of length 450mm long as in repair complete all as specified and directed. Make : Prayag (Cat No. 323) or equivalent make as specified in Particular specifications.

KAY BEE ASSOCIATES

S.S.ENTERPRISE

Tirupati Buildcon Pvt. Ltd.

BHARUKA ENTERPRISES

J B NATH AND SON

Rounaq Enterprise

DILIP CONSTRUCTION

CONSTRUCTION AND MAINTENANCE ENGINEERING CORPORATION