Interior fit-out works in office premises of Ministry of Minority affairs at 6th Floor, MTNL Building, CGO Complex, New Delhi.

Grand Total DSR + Non DSR (including of GST) 31808145.00

Providing and laying in position cement concrete of specified grade exluding the cost of

centring and shuttering-all work upto plinth level.

4.1.8 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) Cum 1.00 6326.05 6326.05

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level.

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand) Sqm 7.8 1018.05 7940.79

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third

course of half brick masonry.

3 FINISHING WORK

3.01 13.4 12 mm cement plaster of mix :

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an

13.60.1 Two or more coats on new work Sqm 1000 137.85 137850.00

Painting with synthetic enamel paint of approved brand and manufacture to give an even

13.61.1 Two or more coats on new work Sqm 150 131.45 19717.50

4 WATERPROOFING WORK

Providing and laying water proofing treatment to vertical and horizontal surfaces of

depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying

cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645

in recommended proportions including rounding off junction of vertical and horizontal

surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed

4.01 22.3 with water proofing compound in recommended proportion including rounding off Sqm 100.00 774.25 77425.00

junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual

bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC

sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each

other with bitumen @ 1.7 kg/sqm).

CEMENT CONCRETE HARDENER : 52 mm thick cement concrete flooring with

concrete hardener topping, under layer 40 mm thick cement concrete 1:2:4 (1 cement : 2

coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick

4.02 11.4 cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone Sqm 100.00 855.90 85590.00

aggregate 6 mm nominal size) by volume, hardening compound mixed @ 2 litre per 50

kg of cement or as per manufacturer's specifications. This includes cost of cement slurry,

but excluding the cost of nosing of steps etc. complete.

5 DOOR,WINDOW & PARTITION

Providing wood work in frames of doors, windows, clerestory windows and other frames,

5.01 9.1 wrought framed and fixed in position with hold fast lugs or with dash fasteners of required

dia & length (hold fast lugs or dash fastener shall be paid for separately).

9.1.1 Second class teak wood Cum 1.00 131576.95 131576.95

Providing and fixing cup board shutters with 25 mm thick veneered particle

board IS : 3097 marked, exterior grade (Grade I), of approved make,

9.130 including IInd class teak wood lipping of 25 mm wide x 12 mm thick

with necessary screws and bright finished stainless steel piano hinges,

complete as per direction of Engineer-in-Charge.

With decorative veneering on one side and commercial

veneering on other side

Providing and fixing modular toilet cubicles top and side wall hung (free from floor) as per

site condition and manufacturer's standard specificationshead frame structure made of

extruded aluminium grade 6063 T50- 5 micron epoxy powder for surface protection, Size

to be 125*70*5T, corner joinery section size to be 40*16.5*1.8T. U channel wall joinery

section size to be 22*16*1.6T. Door stopper section size to be 21*12.5*1.6T. All

intermediate panels, pilasters, doors shall be made up of 12mm thick Solid Compact

Laminate (Phenolic Core Board) as per IS 2046 based on thermosetting resins,

homogeneously reinforced with cellulose fibres making cubicles impervious to Water,

resistant to Fire, etc.

MR Compact laminate should be Greenguard and IGBC certified. Hardware and Fixtures All Each 7.00 48300.00 338100

accessories shall be of 304 grade including all hardware/fittings. If required pilaster are

anchored to the flooring using adjustable SS legs/ SS shoe box. Accessories Std

accessories include SS Hinges, SS Door knob, SS thumb turn indicator, SS coat hook,

and SS channels (All accessories in SS 304 grade) SS legs in SS 316 Grade SS 316

grade shoe box. Std Sizes (W x D x

H)- 1000 mm to 1200 mm x 1550 mm x 2105 mm, ( Height is including 150 mm gap from

bottom) Door Size- 600-610 x 1820-1925 mm.

Providing and fixing plain lining with necessary screws/nuts & bolts/

nails, including a coat of approved primer on one face, and fixed on

9.140 wooden /steel frame work, complete as per direction of Engineer-incharge

(Frame work shall be paid for separately).

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type sqm 100.00 1084.60 108460.00

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-

decorative type, core of block board construction with frame of 1st class hard wood and

5.02 9.21 well matched commercial 3 ply veneering with vertical grains or cross bands and face

veneers on both faces of shutters:

9.21.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws Sqm 30.00 2015.75 60472.50

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all

edges of flush door shutters (over all area of door shutter to be measured).

Providing and fixing Stainless steel satin finish SS 304 grade Tower Bolts SS screws for

wooden doors of approved make and model all complete as per the directions of

5.04 MR Engineer-in-charge Each 4.00 572.00 2288.00

Providing and fixing Stainless steel satin finish SS 304 grade Handles with SS screws for

wooden doors of approved make and model all complete as per the directions of

5.05 MR Engineer-in-charge Each 12.00 2065.00 24780.00

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer

(having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg

5.06 9.83 and door width upto 700 mm), with necessary accessories and screws etc. complete. Each 12.00 1025.65 12307.80

Supply and installation of Aluminium Framed Glass Partitionfor Access and Cabin

System for minimal frame, room dividing solutions.Single glazed mullion free

demountable glass partition using Toughened/ Laminated glass in proprietary natural

anodised/Black aluminium sections ALT 50 of size 50mm x 30mm with Concealed

sealing (No visible Gaskets/Seals) with acoustic rating of Minimum 32 db with third party

test certificate. The profile will have Carpert Groove at the Bottom on both sides for

accomodating max. 8mm carpets. THe Glass to be fixed with help of Proprietary Stability

5.08 MR GRIPPER Clamp to have a stable system. It should consists of intermediate slim Sqm 52.20 5976.00 311947.20

junction profiles for Glass to Glass vertical joints, 90 Degree L Junction and T Junction

profiles suitably to be used as per room configuration designs.No VISIBLE Clip Lines to

provide clutter free view at both side of section. The Glass to be Offset mounted towards

outer edge leading to minimum aluminium frame on one side. Optional Profile Bottom

Seal pair for additional accoustic. Glass thickness - 10( LSG).shall be included in the

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved

brand and manufacture, including providing and fixing top & bottom pivot & double acting

5.09 21.18 hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing Sqm 18.27 4540.70 82958.59

required door fittings, all complete as per direction of Engineer-in-charge (Door handle,

lock and stopper etc.to be paid separately).

Providing and fixing SS tubular handle bar 32 mm outer dia, 3.0 mm thick & 900 mm

long with SS screws etc .complete as per direction of Engineer-in-Charge.

Providing & Fixing Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-

effect film to reproduce Sand-blasting effect on glass with customised designs, thickness

of 2 mil (0.05mm) without adhesive & 3mil (0.8)with adhesive having minimum tensile

strength of 3.5 pound/inch at 73 F(0.6 kg/cm at 23 C). Adhesion after 24hrs of

5.11 MR installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass Polycarbonate: MCS Sqm 19.44 2742.00 53304.48

warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed by

3M India Limited Architectural Market Department. Contractors payment wouldn't be

released until & unless he/she produces orginal warranty certificate from the

6 PARTITION WORK

Providing and fixing plain lining with necessary screws/nuts & bolts/ nails, including a

6.01 9.140 coat of approved primer on one face, and fixed on wooden /steel frame work, complete

as per direction of Engineer-in

9.140.1 12mm thick commercial ply conforming to IS : 1328 BWR type Sqm 200.00 1084.60 216920.00

Providing and fixing metal system up to ceiling height, which includes frame work made

of special section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM,

consisting of Boral U track 52mm wide having equal flanges of 30mm and 0.55mm thick

(Base metal thickness) fastened to the floor slab and ceiling soffit using rawl plugs with

screw at 600mm centers, with first & last fixing point at not greater than 50 mm from

6.02 MR either end. Boral C studs 50mm wide having one flange of 34mm, other flange 36mm, lip Sqm 202.00 876.00 176952.00

size 6 mm and 0.55mm thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not more than 610mm centers.

Maintain 5 to 10mm gap between C Stud and web of U Track.

E4 FIRE RESISTANT GYPSUM BOARD

Providing and fixing partition upto ceiling height consisting of G.I. frame andboards, fixed

to the studs using metal to metal flat head screws, including jointing and finishing to a

flush finish with recommended jointing compound, jointing tape, angle beads at corners

(25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as

per manufacture's specification and direction of engineer in charge all complete. required

board, including providing and fixing of frame work made of special section power

pressed/ roll form G.I. sheet with zinc coating of 120 gms/ sqm(both side inclusive),

consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and

0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre

with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or

metal screws with nylon plugs and the studs 48 mm wide having one flange of 34

mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and

9.105 ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts

and nuts, including fixing of studs alongboth ends of partition fixed flush to wall with

suitable anchor fastener ormetal screws with nylon plugs at spacing of 450 mm centre to

centre, andfixing of boards to both side of frame work by 25 mm long dry wall screws

on studs, floor and ceiling channels at the spacing of 300 mm centre tocentre. The

boards are to be fixed to the frame work with joints staggered to avoid through cracks,

Galvanised M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5

mm each with zinc coating of 120 gms/sqm(both side inclusive)) to be provided at the

horizontal joints of two

75 mm overall thickness partition with 12.5 mm thick double skin fire rated Glass

Reinforced Gypsum (GRG) plaster board conforming to IS: 2095: (part 3) : 1996 (Board

9.105.1 with BIS certification marks) SQM 10.00 1,797.65 17976.50

7 FLOORING WORK

ENGINEERED WOODEN FLOORING Panel 1820 x 145 Total thickness 14 mm

Numbers of panels per pack 6 Nested Lengths Max. 1 plank out of 6 m2 per pack 1,583

m2 Kg per pack 11,99 kg Toplayer PEFC controlled sources EN 13489 ± 3 mm Core

board PEFC controlled sources Spruce Backing layer PEFC controlled sources Wood

Veneer 2 mm Tongue and groove Length Uniclic Width Uniclic Multifit Domestic use

Conditions in each pack 33 years Uniclic - Multifit connection Lifetime Commercial On

request "Wood for Life" Edge Protect + Provides a warranty on build-up of residue dirt

along the edges due to maintenance over the years 10 years "Wood for Life" Surface &

Edge Protect + (lacquered products only) Provides a warranty on pollution of surface

7.01 MR structure and a warranty on build-up residue dirt along the edges due to maintenance Sqm 109.00 8822.00 961598.00

over the years 10 years Surface layer Wood species Oak Origin Europe Finishing UV

cured Oiled finish 2 layers UV cured Lacquer Anti-scratch top coat 5 - 7 layers Natural

variance Due to nature, visual surface can deviate from samples Surface treatments cf

catalogue/website Nature Marquant Vibrant General aspect of installed EN 13489

Lipping - difference in height (mm) ≤ 0,20 difference in width (mm) ≤ 0,20 cupping

lengthwise % ≤ 0,1 cupping in width % ≤ 0,2 Dimensional stability ISO 24339 Cupping

short side max % ≤ 0,30 Changes 30 - 85 % RH Cupping short side min % ≥ - 0,20

Open joints short side (mm) ≤ 0,20 Open joints long side (mm) ≤ 0,30 Underfloor heating

Suitable of special installation instructions.or its equivalent

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the

manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of

7.08 11.41 approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1

cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including

grouting the joints with white cement and matching pigments etc., complete.

Providing and laying Decorative vitrified floor tiles in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and conforming to

IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement

7.09 11.41 mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm

including grouting the joints with white cement and matching pigments etc., complete.

8 FALSE CEILING WORK

Corridor Ceiling - Supplying and Installing 225 Plain GP Powder Coated false

ceiling.Panels : 225C mm wide x 15.5 deep bevel edge, panel length up to 5mtr. formed

out of fabricated from 0.50mm thick Galvanized Sheet (120 GSM Zinc coating mass total

of both sides, 240Mpa yield stress). The top of the panel shall have 50-60 micron

8.01 MR polyester powder coated finish. The panel about each other with a narrow A groove. Sqm 110.00 2759.83 303581.78

Panel Carrier: 32mm wide, 39mm deep, made out of 0.50mm galvanized steel up to

5mtr. made of double backed enameled black with cutout to hold on panel in a module of

Providing and fixing of Triangular Box ceiling manufactured from light weight G.I and

folded into u shape profiles. Each panel has a nominal cell wall thickness of 15 mm to

give a precise engineeredceiling appearance. It has a width of 15mm and height 60mm.

8(b) MR Maximum length available is 2 mtr and its thickness 0.45 in G.I. It has equilateral Sqm 112.00 6121.49 685606.96

triangles having each side length 175mm. It allows fire detection and control system, air

conditioning and other services to be located within the ceiling void.

Providing and fixing of Custom made Vertical curve Polylam Blades Ceilings as per the

design intent. The vertically curve baffle system POLYLAM exhibiting space- delineating

characteristics. The system comprises vertically curve baffle with 100-150mm deep

curved rafters manufactured out of 2.0mm Alluminium to provide wave effect. The

module for fixing baffle shall be 150mm centres as per design requirement. The carrier

rails run perpendicular to the baffles axis and can be mounted with M6 threaded rods

using technical approved fasteners as per EN 13964 standards. The individual baffle

8.02 MR lengths between 1200- 2400 mm can be selected. Baffles lengths less than 1500mm Sqm 20.00 7864.64 157292.75

required two carrier rails mounted at the baffle ends. Baffle longer than 1500mm require

additional carrier rails mounted in the centre. Finish RAL Powder Coated.

No Pre Coated products shall be accepted. The spacing of the grid

angles is according to the requirements of DIN 18168 and DIN EN 13964 and quality

controlled to ISO 9001:2015 approved by SIS & LEED certification by Indian Green

Providing and fixing tiled false ceiling of GI Metal Ceiling Lay in perforated Tegular edge

with electro statically polyester powder coated of thickness 60 microns (minimum) global

white colour tiles of size 600x1200 mm, and 0.5 mm thick with 8 mm drop; made of GI

sheet having galvanizing of 100gms/sqmtr (both side inclusive) with 1.8 mm dia holes

and having NRC (Noise Reduction Coefficient) of 0.5, and backed with a black Glass

8.04 MR fiber acoustical fleece.consisting of main "T" runner with suitably spaced joints to get Sqm 264.10 2856.00 754257.46

required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet,

spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm

thick (minimum) sheet, 1200 mm long spaced between main "T" , ,including factory

painted after bending and perforation,and backed with a black Glass fiber acoustical

Providing & Installation of Baffle ceiling system comprises of 50 mm x 100 mm (50 mm

width & 100 mm Height) U Shape panels in RAL color finish. Panels shall be made of 0.5

mm thick galvanized steel after Powder-coated and length up to 4000 mm. Panel shall

be high corrosion resistance and good color stability. Centre to Centre panel gap will be

150 mm. Panels are fixed on to roll formed carriers 20 mm wide x 40 mm deep out of

0.80 mm G.I sheet Powder-coated color with cutouts to hold the panels in module of 50

8.05 MR mm at maximum 1200 m c/c. Carriers are suspended from the roof or truss by 6 mm dia. Sqm 10 3975.00 39750.00

galvanized steel wire rod hanger with special height adjustment suspension clip at max.

1200 mm c/c. Hangers are fixed to the roof by ‘J’ hooks or ceiling brackets and nylon

inserts. Panels are factory cut in lengths up to maximum 4.0 m to suit site dimensions or

shop drawings. Top cap and side cap are used to cover the edges of the panels.

Providing and fixing false ceiling at all height including providing and fixing of frame work

made of special sections, power pressed from M.S. sheets and galvanized with zinc

coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle

cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm

centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm

long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50

mm of required length with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm

centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall

be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips

made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,

the perimeter of ceiling fixed to wall/partition with the help of rawl plugs

at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of

gypsum board to ceiling section and perimeter channel with the help of dry wall screws of

size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of

tapered and square edges of the board with recommended jointing compound , jointing

tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides

of joint and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers, cutouts

made with frame of perimeter channels suitably fixed, all complete as per drawings,

specification and direction of the Engineer in Charge but excluding the cost of painting

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011

(Board with BIS certification marks)

Providing and Fixing and Installation of Trap Door of Single Leaf with all necessary

hardwares as per Interior Design and the direction of Ebgineer-in-charge

9 WALL FINISHES

Providing and fixing of 6 mm thick premium GRIHA rated Lacquered glass of approved

color by Architect/ Client / Customer, fixed with compatible neutral grade silicon on a

perfectly levelled 12mm thick water proof marine plywood / MDF / Mineral fibre board

which is mounted on RCC wall/any other structure. Lacquered glass must be made

industrially (using curtain coating process); opaque (if viewed against a support wall),

9.01 MR uniformly coated with PU lacquer (50 micron thick coating or more); panel to panel colour Sqm 30.00 4704.90 141146.94

consistency (measured by photo spectrometer); highly durable (passes hardness test for

minimum 220 oscillations); humidity resistance (conforms to BS EN 1036 1999 or

equivalent) ; environmentally friendly having Low VOC (no lead, no arsenic, no copper,

no formaldehyde), low VOC content <100g/l. Silicone used should not react with lacquer

coating (compatible neutral cure silicon)

Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with

necessary screws, priming coat on unexposed surface etc., complete.

Customised Wall Panel - Plain; designed(400mm X 600mm); Supply , Testing and

Commisioning of maintainance free Moss Wall of size 600 x 400 mm panel of natural

9.05 MR light green color/ shade.The plant shall be for indoor use only and requires no Direct Sun Sqm 20.00 36680.00 733600.00

Light or Watering / Spraying of water.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in

gloss / matt/ suede finish with high density protective surface layer and reverse side of

9.06 9.127 adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of

approved quality.

Providing & fixing of panels - 1200mm*2400mm *20mm thickness, NRC = 0.90,

Resistance to fire : REI 90 made out of mineral fibre. Panels to be fixed on framework

made out GI ( 0.60mm thick & 60 MM Width ) sections to form a section of 600mm x

600mm. Panels to be fixed on the Slabs with a minimum of 50mm to 100mm void or gap

9.07 MR with Galvanized screws of length 50 mm & Dia 4.5 mm.In case of islands - vertical shall Sqm 60.47 3477.87 210289.68

be provided with metal section all 4 sides. In case of wall to wall, wall angle shall be

provided towards the wall or UD section shall be provided which shall be concealled as

per the architects design.

Providing & Fixing Vinyl Coated Wall covering as per approved make and pattern as

approved by the client & architect.

Providing & fixing of straight Paneling for walls & Columns structures anchored in floor

slab & celling, cladded with Acrylic Solid Surface 12mm thick sheets straight fabricated

on a single face, finished in matte finish, pasted with industrial grade silicon on a robust

substrate. Substrate shall be with suitable MS box sections [Appx. 15 to 20 kg/ Sqm] as

per structural requirement & duly painted with anti-rust red oxide coating and covered

with 12 mm thick water proof ply as per the design and dimensions approved. The

proposal includes the cost of preparing appropriate substrate surface over the civil

structure provided, along with material cost & installation / fixing on straight walls etc.

FOR ALL WALL CLADDING, TABLE TOPS ETC. COMPLETE

Providing & supplying of Window Blinds as per the approved sample, DUETTE Single

HONEYCOMB SHADES Easy rise operating system and standard design option Original

Non-woven honeycomb shades having soft fabric appearance and high energy-efficient

fabric with high tear strength constructed out of Anti static, resilent, colour fast &

Sanitized Treat 100% spun bonded non-woven polyester fiber & precision manufacture

to form a hexagonally shaped duette pleat . Pleat dimension ¾”Honeycomb structure

with distinct air pocket for energy effeciency and increased insulation. Shadings are

duotone, with neutral tone facing the exterior and color facing the interior .Being a Low

shading co-efficient will have following Comfort rating & solar optical properies. The

HEADRAIL shall measure 49.68 wide and 36.66mm deep & thick 1.27mm extruded from

6063 T6 alu. alloy & shall be powder coated to a smooth finish with a thickness of 40

microns. All cords & cord holes shall be fully concealed inside the fabric structure. As

9.12 MR each of the hexagonal cells is formed individually, pleats operate independent of each Sqm 51.24 15253.00 781563.72

other providing superior pleat retention & structure strength. INSTALLATION

BRACKETS shall be of high tension spring steel suitable for overhead & wall mounting

30mm Duette Hartford mounting bracket. POLYESTER CORD shall be 0.9mm in

diameter & of woven hollow core. ENDCAP shall be molded acrylic color matched to the

head & bottom rails. BOTTOM RAIL shall be a single channel section, measuring 30mm

wide and 12.5mm deep & thickness 1-1.2mm extruded from 5005 H-16 alu. alloy & shall

be powder coated with a smooth finish to a thickness of 15-25 microns. HOLD-DOWN

BRACKET (optional) shall be molded in clear acrylic. It incorporates a pin for

engagement with the bottom rail end-cap. It shall be suitable for sill, face or side facing.

CORD.EQUILISER shall be injection molded from impact modified acrylic with a high

flexural modulus.

Company name "MINISTRY OF MINORITY" cut in SS brush 3d letter (SS304) of text ht.

10.06 MR 600 and of deph 1.5" font to be cut to sizes and directly installed on available base as

per with approved SS fixtures, including necessary hardware, substructure, extra, as No. 1 7926.07 7926.07

specified and directed by Engineer in charge. The letters shall be back lit.

10.07 MR Various Direction signages of exit and washroom identification with LED glow panel and

proper fixture for installation and connection 20"x9"

Providing making and fixing in position custom made SS siganges of sizes 16"x5"as per

10.08 MR Architectural drawings and instruction with approved SS fixtures, approved base

including necessary hardware, substructure extra complete as per detail drawing, as

specified and directed by Engineer in charge

Canvas paintings (Oil/ Acrylic medium)

Concept Creation

Creating design and creation of Art work concept on given subject. With initial visit to

site, preparation of various designs with different material, providing the samples, layout

for approval, improvisation in short listed creative’s and making of final layout for final

production by enlargement of drawing as per ratio of actual size, to prepare detailed

11.01 MR working shop drawings (full scale) based on the Concept drawings/ Views/ site Sqm 5 13067.00 65335.00

conditions, display of actual size dummy/ mock up fabricated in sun board with digital

print for client approval

ART WORK EXECUTION

Towards the cost of doing canvas painting by qualified artist including frame and

installation at site

12 Horticulture and Landscaping

12.01 MR Supply and Planting Draco plant having 6ft height complete. Each 3 16457.52 49372.56

Supply and Planting Monstera plant having 3-4 ft height complete.

Supply and Planting Lolina plant having 2-3 ft height with Coco-peat, mud and manure

Supply and Planting Seaforthia Palm having ht. 90cm to 1.20 m with 6-8 suckers, well

developed, fresh and healthy lush green leaves from bottom to top complete.

Supply and Planting Rhapis Palm having ht. 90cm to 1.20 m with 15 to 18 equal suckers,

well developed, full of fresh and healthy leaves from bottom to top complete.

Supply of full soil fill conical shaped planters of specified volume and dimensions in

stone finish or equivalent. planters to be indigenously made by rotational moulding, with

homogeneous recyclable, industrial grade polymer-resin mix, and textured surface.

planters should have an integrated water outlet hole & plug, single layered peel-proof

12.06 MR construction, light weight, rust proof, uv stabilized, anti-frost feature without any joints,

and easy to clean. planter supplier must give 1 year warranty against any fading or

cracking for both indoor and outdoor use. green plant and laying is extra. potting

instructions as per company catalogue.

GRAND TOTAL 8894549.983

GRAND TOTAL 8894549.983

SCHEDULE OF QUANTITIES - SANITARY & PLUMBING WORKS

DSR VOL-2 QUANTIT

S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

S.NO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

2021 DSR ( INR ) N0N -DSR ( INR )

Supply, Installation, Testing and Commisioning of TABLE TOP BASIN, SIZE: 630X460X130 MM

Supply, Installation, Testing and Commisioing of suitable compatible WASTE COUPLING 32MM-

FULL THREAD- WITH CERAMIC CAP-*130MM HEIGHT *65MM CERAMIC CAP

Supply, Installation, Testing and Commisioing of BOTTLE TRAP (WITH INTERNAL

PARTITION) 32mm SIZE WITH 300mm & 190mm LONG WALL CONNECTION PIPES &

Supply, Installation, Testing and Commisiong of RIMLESS, BLIND INSTALLATION WALL

MR 5 HUNG WC WITH UF SOFT CLOSE SLIM SEAT COVER, HINGES AND ACCESSORIES EACH 6 12098.00 72588.00

SET, SIZE: 375X520X400 MM

Supply, Installation, Testing and Commisiong of PNEUMATIC CONTROL PLATE ACPWHT-

MR 7 Supply, Installation, Testing and Commisiong of ANGULAR STOP COCK WITH WALL EACH 12 2293.00 27516.00

Supply, Installation, Testing and Commisiong of HAND SHOWER (HEALTH FAUCET) WITH

MR 9 8mm DIA 1.2 METER LONG FLEXIBLE TUBE EACH 6 1585.00 9510.00

Supply, Installation, Testing and Commisiong of PNEUMATIC SINGLE PIECE SLIM

CONCEALED CISTERN BODY WITH INSTALLATION KIT & “S-TYPE” DRAIN PIPE

CONNECTION SET FOR WALL HUNG WC (WITHOUT FLUSH CONTROL PLATE)

17.10 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I.

11 brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and

making good the walls wherever required :

17.10.1 Kitchen Sink with Drain Board

MR Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard

flush pipe and CP brass spreader andbrass unions, etc. complete including painting of fittings

and brackets, cutting and making good the walls & floors wherever required.Compact each 4 6439.57 25758.28

MR Providing and Installing Stainless Steel #304 Non Magnetic, Matt Finish Hand Dryer with

operation : Touch-Free Infrared Activation Hand Dry Time : Less than 20 Seconds , Auto Cutoff :

60 Seconds , Sensor Range : 12 – 15 CM , Motor : Brush AC Type ,Motor Speed : 25,000 RPM

, Voltage : 220V / 50 HZ , Rated Power : 1350W (Motor 550 W + 800 W Element) , Current : 15 each 2 17189.81 34379.61

A , Water Splash: IPX1 , Blowing Volume: > 270 M3/H , Air Speed : 95 M/S of Euronics or

equivalent approved make as per selection

MR Providing, fitting and fixing Liquid soap dispenser and liquid soap container complete as

directed and specified.Continental (Cat.No.ACN-1135N) (with glass bottle) jaquar make each 4 829.26 3317.04

17.28 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings

17.28.2 Flexible pipe

17.31 Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality)

13 complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and Each 6 1411.15 8466.90

washers complete.

17.34 14 Providing and fixing toilet paper holder

18.53 Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved quality

conforming to IS : 8931

18.53.1 15 mm nominal bore Each 12 500.35 6004.20

17.61 Cutting chases in brick masonry walls for following diameter sand cast iron/centrifugally cast

(spun) iron pipes and making good the same with cement concrete 1:3:6 (1 cement: 3 coarse

16 sand: 6 graded stone aggregate 12.5 mm nominal size) including necessary plaster and

pointing in cement mortar 1:4 (1 cement : 4 coarse sand) :

18.76 17 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 5 362.40 1812.00

18.7 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe

19 with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC

solvent cement and testing of joints complete as per direction of Engineer in Charge.

Internal work - Exposed on wall

18.7.2 20mm nominal outer dia pipes M 5 325.10 1625.50

18.8 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot

& cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with

clamps at 1.00 m spacing.

20 This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of

cutting chases and making good the same including testing of joints complete as per direction of

Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.

18.8.1 15mm nominal outer dia pipes M 93.1 441.15 41063.50

18.8.2 20mm nominal outer dia pipes M 50 513.75 25687.50

18.51 Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS

standards and weighing not less than 690 gms.

18.51.1 15 mm nominal bore Each 2 708.40 1416.80

Providing, fixing, jointing and testing in position of ISI marked UV stabilized UPVC pipes for

soil, waste, and vent, Type-B as per IS : 13592 suitable for rubber ring joints, including all

neccessary specials and fittings (confirming to IS:14735) i.e. bends, tees, junctions (with or

without doors), reducers, WC connectors, couplers, expansion joints / bellows, cowels, clamps,

rubber rings, clean outs etc. fixing at wall/ ceiling/ floor level supported by clamp & hangers etc.

in concealed / inside duct / under floor & basement ceiling / external work etc. including chase

MR 22.0 cutting as required, excavation and back filling in all kind of soils, suspended from floor under

false ceiling or embedding the pipes laid under floors / building in 75 mm. alround 1:2:4 cement

concrete (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including

cost of shuttering for proper completion of the work, breaking and making good the walls and

floors etc. after pipes have been duly laid and tested. The rubber ring shall confirm to IS:5382.

The Pipes will be supported with threaded G I rods & U clamps with nuts, washers etc on

50x50x5 mm slotted angle. The cost will include all support arrangements. The work includes

commissioning of all pipes lines as per drawings and specifications and as directed by engg-in-

MR charge at site.

MR 110 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 28.50 368.00 10488.00

MR 75 mm dia (Wall Thickness - 3.2 to 3.8 mm) metre 28.42 368.00 10458.38

Providing, fixing, jointing and testing in position ISI marked (IS:4985) UPVC pipes of min 6 Kg/

Sqcm rating with fitting for waste pipe from fixtures to floor trap including reduces, enlarger,

socket, couplers, bends, tees etc including fixing at wall/ ceiling level supported by clamp &

hangers etc. cutting holes in wall/ floors/ slabs and making good the same with cement concrete

1:2:4 complete as required.

Providing & fixing UPVC Floor trap of self cleansing design with stainless steel grating

MR 24 complete in all respects.

MR 25 Plain Floor Trap (4" Ht) with 50 / 75 outlet and with height raiser each 11 353.00 3883.00

MR 26 Extra for providing & fixing 125 mm dia C.P. grating in place of C.I. grating over floor traps. each 11 720.00 7920.00

Providing & fixing of SS Floor Cleanout, round or square with rubber seal and flat round cover

MR 27 with screws and other required fitting complete as required.

SCHEDULE OF QUANTITIES - ELECTRICAL WORKS

DSR (E & M - 2018) / QUANTIT

SNO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

SNO. DESCRIPTION UNIT RATE TOTAL AMOUNT TOTAL AMOUNT

DSR ( INR ) N0N -DSR ( INR )

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC

insulated copper conductor single core cable in surface / recessed medium class PVC

A.18 1.10 conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5

sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Wiring for group controlled (looped) light point/ fan point/call bell point (without independent

switch etc.) with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in

A.19 1.55 surface / recessed PVC conduit, and earthing the point with 1.5 sq.mm. FRLS PVC insulated

copper conductor single core cable etc as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single

A.20 1.5 core cable in surface/ recessed medium class PVC conduit alongwith 1 No 4 sq. mm FRLS Metre 1000 265.00 265000.00

PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single

A.21 1.6 core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos 4 sq. mm FRLS Metre 500 392.00 196000.00

PVC insulated copper conductor single core cable for loop earthing as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch

A.22 1.24 box including connections but excluding modular plate etc. as required.

1.24.4 3 pin 5/6 amp socket outlet Each 150 111.00 16650.00

1.24.5 6 pin 15/16 amp socket outlet Each 60 175.00 10500.00

Supplying and fixing modular blanking plate on the existing modular plate & switch box

A.23 1.26 excluding modular plate as required. Each 30 32.00 960.00

Supplying and fixing following size/module, GI box along with Modular base & cover plate on

A.24 1.27 existing modular metal boxes etc. as required.

B SUBMAIN AND CONTROL WIRING

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FR PVC

B.1 1.14 insulated copper conductor, single core cable in surface/ recessed steel conduit as required

1.14.1 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire Metre 500 146.00 73000.00

1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire Metre 2000 200.00 400000.00

1.14.4 2 X 6 sq. mm + 1 X 6 sq. mm earth wire Metre 150 249.00 37350.00

1.14.10 4 X 10 sq. mm + 2 X 6 sq. mm earth wire Metre 60 543.00 32580.00

1.14.11 4 X 16 sq. mm + 2 X 6 sq. mm earth wire Metre 60 752.00 45120.00

Supplying and fixing of following sizes of steel conduit along with accessories in

B.2 1.20 surface/recess including painting in case of surface conduit, or cutting the wall and making

good the same in case of recessed conduit as required.

Supplying and making end termination with brass compression gland and aluminium lugs for

C.2 9.1 following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1

KV grade as required.

Supply of following XPLE armourned 1.1 KV grade conforming to I.S.7098/1554Aluminium

C.4 MR Conductor Cables :

Supply of following sizes of PVC sheathed PVC/XLPE insulated Aluminium conductor

armoured cable of 1.1 KV grade conforming to IS:7098 part-1 / IS:1554 part-1 respectively &

1 3.5 C x 70 Sqmm XLPE cable RM 151 550.00 82814.00

2 3.5 C x 50 Sqmm XLPE cable RM 150 400.00 60000.00

3 3.5 C x 35 Sqmm XLPE cable RM 150 600.00 90000.00

D.1 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as Each 10 8.00 80.00

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit

D.2 2.10 breaker suitable for inductive load of following poles in the existing MCB DB complete with

connections, testing and commissioning etc. as required.

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB

2.13 complete with connections, testing and commissioning etc. as required.

Supplying and fixing following way, vertical type three pole and neutral, sheet steel, MCB

distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral

D.3 2.5 bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as

required. (But without MCB/RCCB/Isolator)

Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts,

D.5 2.14 residual current circuit breaker (RCCB), having a sensitivity current upto 300 milliamperes in

the existing MCB DB complete with connections, testing and commissioning etc. as required.

E PROVISIONS FOR VOICE, DATA, SECURITY & TV SYSTEMS

Supply, installation, testing & Commissioning of 1 module 16A SWITCH SP 1 way for pop up

E.11 MR Supply, installation, testing & Commissioning of 2 module 16 A Socket for floor box box. Set 8 577.00 4616.00

Supply, installation, testing & Commissioning of Specific Backbox for Wooden Flooring for

E.13 MR Floor Box along with LID and TRIM for tiles/ marble 15 to 20mm thickness material for Set 6 6803.00 40818.00

headband and single cable outlet/ glavanized steel, paint RAL 7031 for floor box.

Supply, installation, testing & Commissioning of flat support plate 8 module for integration of

E.14 MR Mechanism for Floor Box Set 6 263.00 1578.00

Supply, installation, testing & Commissioning of waved support plates for 4 module (2x2)

E.15 MR modules for Floor Box Set 6 1450.13 8700.77

Supplying and fixing following modular switch / socket on the existing modular plate & switch

E.16 1.24 box including connections but excluding modular plate etc. as required.

1.24.7 TV socket outlet Set 20 119.00 2380.00

Supplying and drawing following pair, 0.5 sq.mm FR PVC insulated copper conductor,

E.17 MR unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

Supply, Installation, Testing and Commisioning of Galavanized Iron (GI) Raceways along with

E.20 MR required suitable number of GI couplers for joining raceways and fixing GI brackets and all

accessories complete in all respect as per the directions of engineer in charge

Supply, Installation, Testing and Commisioning of Junction boxes for direct access to cables

at the intersection of raceways supplied completely with base and cover plates, height

E.21 MR adjustable junction box 65- 90 mm including all accessories complete in all respect as per the

directions of engineer i

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

E.22 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng Metre 600 33.00 19800.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes medium class PVC conduit aong with accessories in

E.23 1.21 surface/ recess including cutting the wall and making good the same incase of recessed

conduit as required

Supplying and Installation of following size perforated of painting with powder coating M.S.

cable trays of perforation of not more than 17.5% in convinient sections, joined with

E.24 4.1 connectors suspended from the cieleing with MS suspenders including bolts and nuts painting

suspenders etc as required

4.1.6 450 mm width x 50 mm depth x 2 mm thickness Metre 150 700.00 105000.00

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and

providing masonry enclosure with cover plate having locking arrangement and watering pipe

1 5.6 of 2.7 metre long etc. with charcoal/ coke and salt as required. SET 3 11794.00 35382.00

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

4 5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. MTR 200 57.00 11400.00

Providing and fixing MV danger notice plate of 200mm x 150mm made of mild steel, atleast 2 Nos.

17 2.21 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on 2 226.00 452.00

front side as required

Providing and fixing HT danger notice plate of 250mm x 200mm made of mild steel, atleast 2 Nos.

18 2.22 mm thick, and vitreos enamelled white on both sides and with iscription in single red colour on 2 244.00 488.00

front side as required

SUB-HEAD (B) : FANS & LIGHT FIXTURES:

Supplying, fixing, connecting, testing and commissioning of 1x36-45 watt LED light fixture

suitable for 600x600 ceiling with electronic ballast, with integral ballast, profiled diffuser, grey

1 MR colored body , suitable mounts, suspension cables complete as required, IP 40 rated, CRCA/ 39 4241.00 165399.00

Aluminium housing. Each

Supplying, fixing, connecting, testing and commissioning of surface/ recessed type LED

Linear light with high efficiency white reflector and high transmissive diffuser ,fitting complete

2 MR with, holder, electronic driver, heat sink and LED (less than 10% THD), low depth with die cast 30 6144.00 184320.00

aluminium housing 1 x 30-40W LED with CRI >70, including with driver connections etc. as

required . Each

Supplying, fixing, connecting, testing and commissioning of surface/recessed type LED down-

lighter with high efficiency white reflector and high transmissive diffuser ,fitting complete with,

3 MR holder, driver, heat sink and LED (less than 10% THD), low depth with die cast aluminium 20 2432.00 48640.00

housing 1 x 20W LED with CRI >70, including with driver connections etc. as required.

Supplying, fixing, connecting, testing and commissioning of surface/recessed type LED down-

lighter with high efficiency white reflector and high transmissive diffuser ,fitting complete with,

4 MR holder, driver, heat sink and LED (less than 10% THD), low depth with die cast aluminium 33 1266.00 41778.00

housing 1 x 12W LED with CRI >70, including with driver connections etc. as required.

Supplying, fixing, connecting, testing and commissioning of mirror light luminaire with 1 x 10-

5 MR 14 watt complete with electronic ballast, lamp including connection etc. complete as required. 2 503.00 905.40

Supplying, fixing, connecting, testing and commissioning of LED flexible strip cove light for

6 MR white color including all drivers, connecting cables, controllers , non dimmable, average 5-6 200 541.00 108200.00

watt / metre. Color as per instruction complete as required Meter

Supplying, installation, testing and commissioning of cubical type MV Panel as per

IEC:61439-I made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing,

floor mounted dust and vermin proof, indoor type compartmentalized powder coated of

approved shade after antirust treatment (with min seven tanks ) suitable with busbar

interconnection with suitable size of copper lead/solid Aluminium strips, control circuits &

4 MR-14 bottom base channel of MS section not less than 100mmx50mmx5mm (thick), Fabrication

shall be done in transportable section ,entire panel shall have a common earth busbar at rear

with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line

diagram & specification enclosed with the following switchgears.(Floor Panel )

1 Nos.125 Amps. TPN MCCB (35 KA) with electronic releases.

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. 0-125 Amp. Ammeter (digital type) with inbuilt ASS

400 Amps. TP&N aluminium bus bars (35 KA)

2 Nos. 63A 4PN, MCCB

Supplying, installation, testing and commissioning of cubical type MV Panel as per

IEC:61439-I made out of 14 SWG sheet steel, totally enclosed IP-54 protection, free standing,

floor mounted dust and vermin proof, indoor type compartmentalized powder coated of

approved shade after antirust treatment (with min seven tanks ) suitable with busbar

interconnection with suitable size of copper lead/solid Aluminium strips, control circuits &

5 MR-15 bottom base channel of MS section not less than 100mmx50mmx5mm (thick), Fabrication

shall be done in transportable section ,entire panel shall have a common earth busbar at rear

with 2 nos earth stud cable alleys, cable gland plates in two half as required as per single line

diagram & specification enclosed with the following switchgears. (Main UPS Panel )

1 Nos.63Amps. FP MCCB (25 KA) with electronic releases.

1 Set phase indication lights (R, Y, B)

1 No. Volt Meter (digital type) with inbuilt VSS & control fuses.

1 No. 0-63 Amp. Ammeter (digital type) with inbuilt ASS

200 Amps. TP&N aluminium bus bars (35 KA)

SUB HEAD (H) : UPS SYSTEM

Supplying, installation, testing and commissioning of (N+1) 20 kVA/27KW online double

conversion fully microprocessor based ,indoor type, compact UPS system of mentioned rating

with designed output PF .9 at 40 degree and IGBT based PWM technology to achieve THD

< 5% and input power factor of greater than 0.95 at 50% loading, Efficiency >= 93% at 50

% load, suitable for three phase AC input voltage 320 V to 480 V, 50 Hz +3% / - 3 % and

three phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz with all components

as mentioned in BOQ, specifications and schedule, complete as required and as per technical

specification. Each unit shall be comprising of the following: Total 2 no.s (In parallel)

a 125% rated Rectifier cum charger unit +100% rated Invertor, Integrated in UPS module

100% rated Inbuilt static switch at the invertor output + 2 Nos. 100% rated Inbuilt static

switches at the static bypass line.

c 100% rated Inbuilt Maintenance Bypass.

Web-enabled Monitoring and Management through SNMP protocols for multi-OS

Inbuilt feature required for input phase seq protection and automatic change. UPS should

work on mains and should not go to battery mode in case of input phase sequence change

Supplying, unloading, installing testing and commissioning of necessary VRLA batteries of

suitable size having 15 minutes back up time to 20KVA UPS for full load (75Ah Batteries X

f 20 No.) to be provided. 1 No spare batteryof same AH to be provided and cost to be added.

Note : Concerning vendor needs to furnish the battery sizing calculations at the time of

GA approval and battery size has to be as per the approved GA drawing.

Supply, unloading, installation testing & commissioning of matching cabinet/open racks to

house above mentioned batteries for 30 KVA UPS system along with suitable size

interconnecting cable (for UPS to Battery and battery to battery), MCCB etc. complete as

required & as per specifications.

Supply,installation testing and commissioning of UPS monitoring software suitable for RJ-

h 45 communication and capable of giving pop up messages for all alarms received from UPS.

All shall be capable of the following:-

Giving notifications like e-mail, paging notification, broadcast notification, battery

replacement notification, run event-based scripts.

Event logging, data logging and action logging (with date, time, description of fault and

k Run the battery diagnostic test.

l Automated unattended shutdown of computers.

m Local notification through audible alarm.

Software should support :

n latest version of Microsoft Windows/ Server, AIX, HP-UX, Sun Solaris, Linux, Novell

FIRE ALARM & DETECTION & PA SYSTEM

Supplying, installation, testing & commissioning of repeater panel wih 640 character/ Touch

screen LCD display with inbuilt reset, acknowledge and silence switches complete as

MR SITC Loop Card capacity of 159 detectors For BMS Fire integration Each 1 80451.00 80451.00

MR SITC of Networking card for BMS integration Each 1 50751.00 50751.00

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal

detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS

Box having two LED, metallic cover complete with all connections etc as required

Supplying, installation, testing & commisssioning of intelligent addressable programmable

sounder complete as required.

Supplying, installation, testing & commissioning of fault isolator complete with base as

Supplying, installation, testing & commissioning of intelligent addressable thermal detector

with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of

addressable fire control module complete as required

Supplying, installation, testing & commissioning of addressable manual call point complete as

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as

Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed

copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath

11 17.5.2 complete as required. Metre 450 141.00 63450.00

17.3 PUBLIC ADDRESS SYSTEM

Supplying, installation, testing & commissioning of 6 zone, voice alarm controller with USB,

1 17.3.1 MP3 player (including 6 zone button paging station) with seamless integration facility with Each 1 126399.00 126399.00

main fire alarm panel for voice evacuation complete as required.

Supplying, installation, testing & commissioning of 1.5/3/6W ceiling speaker complete as

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall speakers

complete as required.

Supplying, installation, testing & commissioning of ceiling/wall mounted loud speaker, 3/1.5

Watt in ABS enclosure complete as required.

Supplying, installation, testing & commissioning of digital audio amplifier 500 Watt, 25V rms

operating at 240 volt AC supply complete as required.

Supplying, installation, testing & commissioning of Voice command keypad 6 zone, with

microphone assembly complete as required.

17.5 Cabling & Wiring

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the

7 17.5.3 existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

7.1 17.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Metre 750 51.00 38250.00

SURVEILLANCE SYSTEM (CCTV)

Supply, Installation & commissioning of Reliable & Secure 4 MP Dome Camera with

minimum IR distance 40 mtrs or better .1/2.7” Progressive Scan CMOS ,2.7 mm to 12 mm

motorized varifocal lens , simultaneosus quad H.265+ streams ,min illumination : 0.01 Lux @

color, 0 Lux with IR @ B/W , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , SD card

support upto 256 GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should

1 MR support 25 fps@5MP ,Edge analytics : line crossing , perimeter intrusion ,Face detection with Nos. 6 45345.00 272070.00

deep learning , pedestrian detection ,cross counting , stationary object , In built IR LED with

IR Distance upto 50 meters or better , IP 67 weather proof and IK 10 vandal resistant housing

, POE.ONVIF profile S , G & T, UL,CE,FCC certified

Supply, Installation & commissioning of Reliable & Secure 4 MP PTZ camera 1/2.8" CMOS

progressive sensor, 5MP (2592 X 1944), with min IR distance 150 mtrs or better , Min

2 MR illumination : Color 0.5lux @ F1.2(AGC ON) ; B/W 0.05 lux, WDR 120db or higher, Shutter Nos. 1 225000.00 225000.00

time : 1/1 ̴ 1/10,000 s, , fixed focal lens 4.3-129 mm , Min 30X Optical & 12X Digital zoom,

Privacy mask 04, IP 66 , POE ,ONVIF profile S/ G/ Q . UL,CE,FCC certified

Supplying, Installation, Testing & Commissioning of Reliable & Secure 32 channel NVR ,

ONVIF compliant , recording bandwidth 640 Mbps , output interface 1 HDMI (up to 4K), 1 VGA

, Alarm in/out :16ch in / 4ch out , 1 X RJ45 ethernet , iOS smartphone support , 8 HDD

support , each HDD slot support upto 8 TB HDD , RAID support , 1x3.0 USB for backup

/upgrade , 2x 2.0 USB for mouse , Artificial Intelligence Support having face recognition with

3 MR compatible deep learning supported cameras, AI-Face registered quantity upto 10,000 ,A.I Nos. 1 210000.00 210000.00

maximum captured quantity 200,000. UL,CE,FCC certified. OEM Should not be blacklisted

globally. The contractor need to ensure that NVR should be supplied with all required

accessories to make CCTV System in functional state. .

Supplying, Installation , Testing & Commissioning of 43 inch 4K LED display, Landscape &

Orientation Resolution 3840X 2160 (16.9) UHD. Brightness 350 NIT, Built in Wi-Fi and

Bluetooth inbuilt digital signange player, Android Builtin Memory 16 GB, Processor Cortex

A55x4 1.1 Ghz Processor Triple Core Mali 470 600 MHz 16 GB Memory24/7 operation,

4 MR Brightness 350 nits, Contrast Ratio 1100:1, 178/178 Viewing Angle (Horizontal:Vertical), 8ms Nos. 1 54933.00 54933.00

Response Time (milli seconds) Built in speaker (10W+10W). Inputs DVI-D, Display Port,

HDMI & Dual USB Plug & Play , RJ45 LAN, Output Stereo mini Jack, Remote

Controlling of device Display remotely controlled Internal/External, BIS Certificates etc.

complete in all respect etc.as required

Supplying, Installation & testing of Hard Disk 8TB SATA Surveillance Hard Disk (HDD) in NVR

Complete in all respect.

SUB HEAD - IV : TV, DATA, VOICE NETWORKING

Passive Components

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed

Steel/ PVC conduit as required.

Supply, installation, testing & commissioning , Cat 6A STP Jack PCB based Information

Outlet (I/O) RJ45, TIA‐568.2-D Category‐6A. ETL Channel test report as per ISO/IEC 11801,

ANSI/TIA 568.2-D High‐impact, flame‐retardant,UL 94V-2 for plastic part – ABS, Plug

2 MR Insertion Life Min. 750 times as per IEC 60603‐7 Zinc Alloy housing, Pin in Jack Material - 50 Nos. 240 270.00 64800.00

U Gold over Nickel, Insulation Resistance - 100 M ohm, Contact Resistance – 20m ohm,

Current rating - 1.5A Max

Supply, installation, testing & commissioning Cat 6A STP, 24‐port loaded Modular Straight

Jack Panel for 24 nos. STP ports patch panel is eight ports RJ45 modules applied and

3 MR suitable for 22-24 AWG stranded and solid wire, compatible with 110 & Krone punch down Nos. 12 5593.00 67116.00

tools. Jack Panel should be tested under ETL 4 Connector channel Test report, RoHS

Compliance,Insulation Resistance 100 M ohm Max Contact Resistance 20m ohm

Supply, installation, testing & commissioning Cat-6A S/FTP Low Smoke Zero halogen (LSZH)

Patch Cord (Length – 1 Mtrs) Cat 6A S/FTP Patch Cable, TIA‐ 568C Category‐6A, ETL

4 MR report as per ISO/IEC 11801, ANSI/TIA-568.2-D-2018 , RoHS Compliant. Patch cords shall Nos. 240 238.00 57120.00

be of Solid copper cable with ETL Listed. Plugs shall be designed with Snag less

Supply, installation, testing & commissioning Cat-6A S/FTP Low Smoke Zero halogen (LSZH)

Patch Cord (Length – 2 Mtrs) Cat 6A S/FTP Patch Cable, TIA‐ 568C Category‐6A, ETL

5 MR report as per ISO/IEC 11801, ANSI/TIA-568.2-D-2018 , RoHS Compliant. Patch cords shall Nos. 240 274.00 65760.00

be of Solid copper cable with ETL Listed. Plugs shall be designed with Snag less

Supplying & Fixing of Floor Standing Network/Server Rack - 42U / 800w / 800d, with Heavy

Duty Extruded Aluminium Frame for rigidity. Top cover with FHU provision. Top & Bottom

cover with cable entry gland plates. Two pairs of 19” mounting angles with ‘U’ marking.

Depth support channels - 3 pairs. With a Overall Weight Carrying Capicity of 500Kgs. Side

6 MR Panels - 42U/800d Front MS Door Perforated honeycomb 42U/800w Rear MS Door Split Nos. 1 45656.00 45656.00

Perforated honeycomb 42U/800wFan 90CFM 230V AC, 4” dia Castors with Brake (set of 4)

Vertical Cable manager 80mmW 42U Shelf, Stationery 700mm N/W PDU 12Sockets

5/15Amps with MCB Mounting Hardware (Pkt. Of 20) earthing Kit 150mmH Cable manager

1U MS with Loops complete in all respect.

Supply, Installation, testing and commissioning of 1 U Horizontal Wire Manager 60mm depth

Supply, Installation, testing and commissioning Patch Cord Lable for Rack side (Pk of 2500

9 MR Supply, Installation, testing and commissioning Velcro's Roll (15 Mtr. Per Roll) Nos. 5 219.00 1095.00

Supply, installation, testing & commissioning Single / Dual / Four Port Faceplate of size 3x3

Material should be High‐impact, ABS, UL94-HB, with white color, General Specifications:

10 MR Colour: White 86*86 mm for Single and Dual and 146" 86 mm, Quad Faceplate accepts four Nos. 65 219.00 14235.00

keystone jacks, Faceplates shall accept all Modules for UTP, STP. RoHS Compliant.

Supply fitting, fixing and testing of 9 U Wall mount rack of Width (mm)-600, Depth (mm) - 500,

Approx.Net Wt (kg) - 20, CRCA 'D' Grade thickness (mm) - 1.2, Powder Colour for Cabinet -

11 MR RAL9002, Glass - 4mm Toughened Tinted Glass Door, Accessories:, Fan & with all required Nos. 1 5825.00 5825.00

Supply, installation, testing & Commissioning of 8(2X4) modules brushed brass/copper colour

12 MR pop-up boxes.(Inclusive of All switch socket, DATA/bnc/usb/hdmi/vga/ outlet, telephone or as Nos. 4 5864.00 23456.00

ACTIVE COMPONENTS

Supply, Installation, Testing & Commissioning of Core Switch with switching capacity of 480

Gbps,frwarding performance of 357.12 Mpps with 20-port 10GBASE-T and 4-port 10GBASE-

T/SFP+ Combo Port uplink module from day1, dual hot swappable internal power supply, 48

K MAC Address Table with Physical & Virtual Stacking , ERPS Support, 802.1AX . IP

Interface IPv4: 256 & IPv6: 256 , VRRPv2/v3 support , the Swithc Should have iSCSI

1 MR Awareness with Data Center Bridging (DCB) should support DHCPv6 Guard,IPv6 RA Guard, Nos. 1 344089.00 344089.00

IPv6 ND Inspection, ARP Spoofing Prevention, DoS Attack Prevention, WAC/MAC, 802.3ah

Ethernet Link OAM, Dying Gasp, 802.1agCFM, Y.1731 OAM

DDM, RM0Nvl/v2, with Multiple Images/ Flash File System Image & Configuration .

Shouldsupport advance layer3 (RIPng,OSPF) or its equivalent

Supply, Installation, Testing & Commissioning of Firewall as per the networking integrated

configuration requirement or its equivalent

Supply, Installation, Testing & Commissioning of Switch with at least 24X10/100/1000BASE-

TPOE+Ports and2x10GBase-T and 4XSFP +Ports, Switching capacity should be 168Gbps,

Switch should support 16L3 IP interfaces, ACL, QOS, VRRPv3,Equal-CostMulti-

3 MR Path(ECMP),UDPhelper,Policy-based Route (PBR),802.1x, Embedded 6k V surge protection Nos. 2 121444.00 242888.00

one thernet ports, Switch should have console port, RJ45 Management Portand USBport,

Should support internal/external redudent power supply for 1+1 redundancy and load

sharing.Certification:CE,FCC,BSMI,CBandUL or its equivalent

Supply,Installation,Testing&Commissioning of Switch with at least 24X10/100/1000BASE-

TPortsand2x10GBase-T and 4XSFP+Ports, Switching capacity should be168Gbps ,Switch

should support 16 L3 IP interfaces, ACL,QOS,VRRPv3,Equal-CostMulti-

4 MR Path(ECMP),UDPhelper,Policy-based Route(PBR),802.1x,Embedded 6kV surge protection Nos. 12 93411.00 1120932.00

one thernet ports, Switch should have console port, RJ45 Management Port and USB port,

Should support internal/external redudent power supply for 1+1 redundancy and load sharing.

Certification:CE,FCC,BSMI,CBandUL or its equivalent

Supply, Installation, Testing & Commissioning of Server based IPPBX along with

operarator IP Phone with 21 BLF keys

Main Unit Power Supply

Auto Attendant/IVRs

1 MR Voice Mail for all users with email faciliy Music on Hold, Speed Dial Each 1 350766.00 350766.00

Hunt Group, Call Routing And many more…

1 PRI port with recording facility 120 Analog Extensions through SIP Based Media

Gateway. System should support VM ware.with 3 years Support/warranty

Supply Installation, Testing and Commissioning of Integrated Viocemail System 4 Level IVR

software with 6 different languages and 4 time schedule(As per OEM).

3 MR Supply Installation Testing and Commissioning of IP Phone Type-I Each 10 15669.00 156690.00

4 MR Supply Installation, Testing and Commissioning of Digital Analog Phone. Each 25 2893.00 72325.00

Supply, installation, testing & commissioning of Dual-band 802.11abgn/ac Wireless Access

Point ,4X4: • 2.4 GHz - Up to 800 Mbps 5 GHz - Up to 1733 Mbps , dual ports ,802.3af PoE

support.Supports enhanced security – WPA2-Personal & WPA2-Enterprise, WPA3 . Supports

1 MR two 10/100/1000 Ethernet ports. Support LACP or Static Link Aggregation Does not include Each 6 28666.00 171996.00

power adapter or PoE injector. Should Includes Warranty and Mounting Kit complet in all

respect. complet in all respect.with 3 years Support/warranty

Supply, installation, testing & commissioning ofWi-Fi Controller with 4 x 10/100/1000 Mbps

• 2 x USB 2.0 ports, • 2 x 10/100/1000 Mbps option ports for enabling VPN/Router/Firewall

2 MR function Each 1 241343.00 241343.00

• 1 x 10/100/1000 Mbps console port, with 10APs license,PowerSupplyalong with 3 year

support. with licence for 12 users

AV room Equipment

Supply, Installation, Testing and Commissioning of 75 inch 4K LED display, Resolution 3840X

2160 (16.9) UHD, Brightness 500 nits, Contrast Ratio 1100:1, Built in Speaker (10W+10W).

Inbuilt OPS Slot Inputs HDMI IN X 4 , DP X 1, VGA X 1, Video IN X 1,Component x 1, USB X

1 MR 4, RJ45 X 1, RS232 X 1, Audio IN X1, DP Out x 1/ DP Out x 1, Video Out x 1, Duty Cycle 24x Nos 1 190946.00 190946.00

7, Controlling of device Display remotely controlled, Internal/External, BIS Certificates etc.

complete in all respect etc.as required

Supplying, Installation , Testing & Commissioning of 55 inch 4K LED display, Landscape &

Orientation Resolution 3840X 2160 (16.9) UHD. Brightness 350 NIT, Built in Wi-Fi and

Bluetooth inbuilt digital signange player, Android Builtin Memory 16 GB, Processor Cortex

A55x4 1.1 Ghz Processor Triple Core Mali 470 600 MHz 16 GB Memory24/7 operation,

2 MR Brightness 350 nits, Contrast Ratio 1100:1, 178/178 Viewing Angle (Horizontal:Vertical), 8ms Nos 4 78731.00 314924.00

Response Time (milli seconds) Built in speaker (10W+10W). Inputs DVI-D, Display Port,

HDMI & Dual USB Plug & Play , RJ45 LAN, Output Stereo mini Jack, Remote

Controlling of device Display remotely controlled Internal/External, BIS Certificates etc.

complete in all respect etc.as required

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE

3 1.19 insulated, shielded with fine tinned copper braid and protected with PVC sheath in the exisitng MTR 600 33.00 19800.00

surface/recessed steel/ PVC conduit as required

Supplying and fixing of following sizes of medium class PVC conduit along with accessories

4 1.21 in surface/recess including cutting the wall and making good the same in case of recessed

conduit as required.

Supply, Installation,Testing & Commissioning of Projector 6000 Lm, WUXGA resolution, Laser

light source, 3 LCD projector with HDMI X 2, VGA IN X 2, VGA Out x 1, Video IN X 1, Audio

1 MR IN X 3, Audio Out x 1, USB Type A X1, RS232 X 1, LAN X 1, HD Base-T X 1, 1.6X Zoom Nos 1 433561.00 433561.00

lens, 30,000,00 :1 Contrast ratio, 20,000 hours light source life along with fixed zoom lens of

throw ratio 1.09 - 1.77:1.

2 MR Supply, Installation,Testing & Commissioning of Motorised Lift for Projector mount. Nos 1 28844.00 28844.00

Supply Installation Testing & Commissioning of Motorized Projection Screen 135 inch

3 MR aspect ratio 16:10 with tublar motor & RF remote commander, Fabric matt white. Motorised Nos 1 29735.00 29735.00

front Projection Screen, wide(8ft) X hight (6ft) with 'Remote Control.

Video conferencing

SITC of HD Video Conference system with Omni directional Boundary layer microphone with

following features and items with their specifications

Multipoint (1+5) ---------------01 No.

# 1080p/60fps (Full HD)

# 10x/12x Optical Zoom PTZ Camera

# Angle of View : 72.5°

Boundary Microphone ---- 01 No.

# 4m radius, Max. 4

features : 1. Inbuilt USB Memory Recording to record live video

image and sound of local and remote sites to USB

memory without any expensive external equipment.

2. H.239 Dual Stream

3. H.281 Remote Camera Control

4. AV- QoS Technology

5. Dual Network

6. Connect up to Three Display/ Monitor

7. Expandable upto 1+9 (Need to procure License Key Extra)

System Should support soft client on Android, IOS and Windows Platform

Optional : (For Web/Cloud based Conferencing: it enables to use Camera,Microphone and

Display as PC Peripherals of any Web

Conference/ any cloud base applications i.e. Microsoft Teams,

Skype, Google Meet, Zoom, WebEx, Skype, blujeans etc....) …. Shall be charged extra as per

the requirement.

SITC of 7 inch Touch panel, screen resolution 800 X 480, brightness 350cd/m2,

contrast ratio 400:1, Ethernet Communication RJ45 port, inbuilt speaker & mic, etc.

2 MR Should be supplied with table mount as well as wall mount kit. Should have appropriate Nos 1 95598.00 95598.00

app.complete job with SW programming etc.

SITC of Touch Panel Control System should be equipped with at least 6

bidirectional RS-232 serial ports, at least 8 IR ports, at least 8 Digital I/O

Supply ,installation ,testing and commissioning of Output Video Encoding: HDBaseT Class B

,Encoding Data Rate: 9.2Gbps, End to End Latency: 10 s (micro seconds), Audio Formats:

2ch Analog/PCM | Multichannel: LPCM, Video Resolutions (Max) Video Resolutions:

4096x2160p @60Hz 8bit 4:2:0, Video Resolutions HDMI: 15m/49ft / 15m/49ft / 7m/23ft /

(70m/230ft) / (40m/131ft) / (40m/131ft) Supported Standards: DCI | RGB Maximum Pixel

Clock: HDMI: 600mHz | HDBaseT: 297MHz Communication and Control HDMI: HDMI |

HDCP 2.2| EDID | DVI/D supported with adapter (not included) HDBaseT: HDMI | HDCP 2.2 |

EDID | 1-way PoC Receiver to transmitter,RS-232: 1x RS-232: 3-pin Phoenix (Transmitter

and Receiver) Ethernet: 1x 8-pin RJ-45 female | IP Control (TELNET) Relays: 2x Relay: 3-pin

Phoenix (Receiver Only) Power Supply: 12V DC 3A Max Power Consumption: Transmitter:

7W | Receiver: 17W PoC: IEEE 802.3af 15.4 W Max

Maximum BTU: Transmitter: 24 BTU/hr | Receiver: 58 BTU/hr complete with standard

accessories as required.

CONFERENCE TABLE

Supply, Installation, testing and commissioning of HDCP 2.2 compliant HDMI 1.4v 3D

compatible CEC pass through Cascadable up to 7 times One-way PoH (Power over

HDBaseT) Multichannel audio supports 7.1 DTS Master HD and Dolby True HD Includes:

5 MR Receiver, mounting brackets, IR emitter and receiver, 2 and 3-pin phoenix male connectors Nos 1 138525.00 138525.00

Audio Format Supported: Multichannel digital audio supporting 7.1 DTS Master HD and Dolby

True HD with standard accessories as per tender specifications.

Supply, Installation, Testing and Commisioning of 6x HDMI in: 19-pin type A,6x HDMI Out: 19-

pin type A,6x Audio Out: RCA Female Stereo (L/R),6x S/PDIF Out: RCA Female,2ch PCM |

Multi Channel Up to 5.1 DTS and Dolby Digital,1920x1080p @60Hz 12bit,Supported

Standards DCI | RGB | HDR | HDR10 | Dolby Vision | HLG | BT.2020 |

BT.2100,Communication and Control HDMI 2.0 | HDCP 2.2 | EDID Input supports DVI/D and

6 MR DisplayPort Dual-Mode (DP++) v1.3 with adapter (not included),CEC power triggering | Nos 1 167515.00 167515.00

Requires CEC compatibility,IR 1x Front Panel IR Sensor | Handheld IR Remote Included | 1x

IR Ext 3.5mm (1/8in) TRS Stereo,RS-232,1x RS-232: 9-pin DB9 Female | Matrix Control |

Telnet commands supported,Ethernet 1x LAN: 8-pin RJ-45 Female | 10/100 Mbps auto-

negotiating | Built-in Web UI | IP Control, Safety and Emission CE | FCC | RoHS,

Supply , installation , testing and commissioning of Digital Chairman unit with minimumm

430mm long gooseneck microphone. Microphone connector compatible with standard 3-pin

XLR microphones. Individual adjustable gain control. programmable bottons for Multiple

functions like all delegate mute etc. colour RGB rear LED bar for general visualisation

7 MR purposes. Multi-colour LED on the speak button for user’s colour preferences. LED display Nos 1 59202.00 59202.00

for volume control and listening channel selection. High quality speaker for enhanced speech

intelligibility. 24-bit / 48kHz High Resolution Audio. 2 x RJ45 Port for connecting to the Control

Unit and other Discussion Units and 1 x stereo mini jack headphone output.

Supply ,installation ,testing and commissioning of Cable Management System Cable Cubby ,

Black, Hydraulic open & close system, 2 x Universal Power ,2 x RJ45 Network, 1 x VGA, 1 x

10 MR 3.5mm Audio, 1 x HDMI, 1 x USB Charger Sockets complete with standard accessories as Nos 4 31694.00 126776.00

Supply , installation , testing and commissioning of Delegates Digital Discussion unit with long

stem gooseneck microphone with Configurable user type unit e.g. delegate, chairman, VIP.

Microphone connector compatible with standard 3-pin XLR microphones. Individual adjustable

gain control. Multi colour RGB rear LED bar for general visualisation purposes. Multi-colour

11 MR LED on the speak button for user’s colour preferences. LED display for volume control and Nos 6 42740.00 256440.00

listening channel selection. High quality speaker for enhanced speech intelligibility. 24-bit /

48kHz High Resolution Audio. 2 x RJ45 Port for connecting to the Control Unit and other

Discussion Units and 1 x stereo mini jack headphone output.

Supply , installation , testing and commissioning of Digital Microphone control unit/processor

for Connection of microphone units in two lines or a ring using standard ethernet cables.

Supports up to 100 discussion units mininum. Cascade capability to handle upto 300 or more

discussion units and minumum of six interpretation units for upto 3 spoken languages in the

meeting. minimum 4 configurable balanced outputs. minimum 2 Mic/Line In + 1 Aux In + 2

12 MR Return In. Conference Mode: Free talk, Request to talk and Full remote. various override Nos 1 150576.00 150576.00

settings: ‘LIFO’, ‘FIFO’ and ‘Non Override’; manual or voice activation and flexible ‘Mic On

trigger mode’. Web remote interface facilitates pre-meeting system setup and management

of the live discussion through a web browser. Built-in Wav and MP3 Recorder to external

USB memory devices, Built-in feedback suppressor and digital audio processing (DSP).

Supply, Installation,Testing & Commissioning of Wireless Presentation Device to be Input 4x

HDMI 19-pin type A | 1x VGA 15-pin DSUB15 VGA 1x Audio In (VGA Audio) 3-pin Screw

Down Phoenix Connector,output 1x HDMI 19-pin type A | 1x Audio Out 3-pin Screw Down

Phoenix Connector 1x Ethernet 8-pin RJ-45 female - 10/100/1000 Mbps auto-

negotiating,Audio Formats 2ch PCM,Output Video Encoding H.264/MPEG-4 AVC,Encoding

Data Rate 31 Mbps | Configurable,End to End Latency Low Latency Mode: 60~90ms | High

Latency Mode: 250~300ms,Video Resolutions (Max) HDMI: 1920x1080p @60Hz 16bit

(7m/23ft) | VGA: 1920x1080p @60Hz 16bit (7m/23ft) Ethernet: 1920x1080p @60Hz 16bit

(100m/328ft Point to Point),HDMI HDMI 1.3 | HDCP 1.4 | DVI/D supported with adapter (not

,Ethernet 1x 8-pin RJ-45 female - 10/100/1000 Mbps auto-negotiating,RS-232 1x RS-232 1

(Switcher Control) 3-pin Phoenix Connector | 1x RS-232 2 (Device Control) 3-pin Phoenix

Connector,Hardwire Contacts 1x Contact In 5-pin Phoenix Connector | 1x LED Out 6-pin

Phoenix Connector,Multiple control methods: front panel display buttons, built in Web

UI,contact closure panels, and RS-232 or IP control systems with standard accessories as

Supply , installation , testing and commissioning of System cable CAT5 with RJ45 Connector

2m complete with standard accessories /or as required.

Supply , installation , testing and commissioning of System cable CAT5 with RJ45 Connector

20m complete with standard accessories as required.

Supply, Installation, Testing & Commissioning of UHF Wireless Cardioid lapel Micropphone

system with 55" cable terminated with locking 4-pin HRS type connector.Frequency Response

of 60 Hz to 16 kHz , RF Sensitivity 10dBμV (S/N 60dB @ 20 kHz deviation) or better, Total

16 MR Harmonic Distortion <1.0% (at 1 kHz, ±20 kHz deviation) or better, Dynamic Range > 108dB Nos 1 59380.00 59380.00

or better, on/off switch operating range 60 mtrs or better, RF Power Output: 10 mW or better,

maximum Output level XLR / Balanced: +4 dBV & 6.3 mm (¼"") / Unbalanced: -2 dBV.

Supply , installation , testing and commissioning of Horizontal Ceiling Array-Microphone (back

electret); Linear frequency response with high bandwidth; Fixed connecting cable 3-pin XLR

17 MR connector; Frequency response : 130 - 17,000 Hz complete with standard accessories as Nos 1 59380.00 59380.00

Supply , installation , testing and commissioning of Supply, Installation, Testing &

Commissioning of 15W uniform coverage cabinet speaker with high-performance, two-way,

full-range, 4" (102 mm) surface mount. The mounting system allows for 90 degrees of rotation

horizontally, and 45 degrees of rotation vertically, and it can be easily installed on walls and

ceilings. The mounting system comes already assembled and ready to be used. The speaker

utilizes a 15 W transformer, that offers a selection of 3.7 W (70 V only), 7.5 W or 15 W

delivered to the speaker system using either 70 V or 100 V lines. Selection is done with a

Euro block connector. Long throw 4" (102 mm) woofer housed in a fire rated ABS plastic

enclosure for extended LF performance down to 75 Hz.

Technical Specifications

- Input transformer (70V/100V): 15 W

- Frequency response (-10 dB): 75 Hz - 20 kHz1

- Sensitivity: 86.5 dB2

- Max SPL (calculated): 98.5 dB (104.5 dB Peak)

- Coverage angle: Horizontal 110°, Vertical 110°

- Power handling: 15 W (60 W Peak) Continuous Pink Noise (100 hours) with standard

accessories as required.

Supply, Installation, Testing & Commissioning of Digital Smart Mixer with minimum 4

balanced mic inputs, 2 balanced Mic/Line inputs and 1 stereo unbalanced input; Minimum 1

stereo and 2 mono outputs; 2-channel USB audio interface for soft codec (Skype, WebEx)

integration or playback from computer; Full digital processing on inputs and outputs; minimum

19 MR 8 x 3 audio routing matrix; 6-channel Smart Mix (gate or gain sharing); Onboard acoustic echo Nos 1 105585.00 105585.00

canceler (AEC) processing; Front panel direct operation and Web Remote functionality; IP

control for third-party CCS administration; Up to 6 mixers can be linked using Cat5e cable.

Supply, Installation, testing and commissioning of high impedence Class D Dual zone

amplifier with output power of upto 2x120W @ 70/100V. frequency response of 55 Hz - 20

kHz (+0/–3 dB, @ 1 W reference 1 kHz); THD <0.3% at rated power. Channel Separation ≤

20 MR –60 dBV (below rated power, 1 kHz), Dynamic range > 88 dB. Shall include priority override Nos 1 61623.00 61623.00

and Fire alarm interface, shall include necessary loudspeaker EQs complete with standard

accessories as required.

Supply , installation , testing and commissioning of 08 Port POE Switch for System

Interconnectivity complete with standard accessories as required.

Supply , installation , testing and commissioning of Wifi router complete with standard

accessories as required.

Supply , installation , testing and comissioning of 6 ft HDMI Cable with High–Quality

Connectors — 24K gold–plated connectors resist corrosion, and offer the best possible

23 MR connectivity and provides 4K@60Hz (4:4:4) resolution complete with standard accessories Nos 3 2493.00 7479.00

as per tender specifications.

Supply , installation , testing and comissioning of 10 ft HDMI Cable with High–Quality

Connectors — 24K gold–plated connectors resist corrosion, and offer the best possible

24 MR connectivity and provides 4K@60Hz (4:4:4) resolution complete with standard accessories Nos 5 3917.00 19585.00

as per tender specifications.

Supply , installation , testing and comissioning of 6 ft 15–pin HD (M) to 15–pin HD (M) &

3.5mm Stereo Audio Cable. Easy Connection — Pre–terminated with molded 15–pin HD

25 MR connectors (male to male), gold–plated pins and thumbscrews and a 3.5mm stereo mini jack. Nos 6 3026.00 18156.00

complete with standard accessories as per tender specifications.

Supply, Installation, Testing and Comissioning of 4 pair shielded STP cable complete with

standard accessories as per tender specification.

Supply, Installation, Testing and Comissioning of 2 core +shielded 24 AWG Microphone

cable complete with standard accessories as per tender specification.

Supply, Installation, Testing and Comissioning of Neutrik bulk connector and other

accessories as per required.

Supply, Installation, testing and commissioning of 19" 24U AV rack complete with standard

accessories as per tender specification.

Total of Electrical items 3541613.00 11585640.92

SCHEDULE OF QUANTITIES FIRE FIGHTING SYSTEM

S No DSR/MR DESCRIPTION UNIT QTY RATE TOTAL TOTAL AMOUNT

S No DSR/MR DESCRIPTION UNIT QTY RATE TOTAL TOTAL AMOUNT

AMOUNT NON-DSR (INR)

Providing and fixing ISI Marked of approved make Fire

1 MR Extinguishers complete with all accessories as per

manufacturer's specifications.

a MR a) CO2 gas nozzle type - 9 Litre capacity (IS:15683). NOS 4 11672.00 46688.00

b) Mechanical Foam gas cartridge type. 9 Kg capacity

c) ABC dry powder stored pressure type 6 kg capacity

Grand Total 74448.00

Grand Total 74448.00

SCHEDULE OF QUANTITIES FURNITURE WORK

Snos. Item Specificatoins unit Qty Rate Amount Ref. Image

Providingin place of main table with overall size of table 1650 x 1950 x 750mm. The main table shall be of size 1650 x

750 x 750mm. The side unit shall be 1200 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-

laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap

within-build power box are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF

one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty

panel is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC

membrane pressed on to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

Main Table 1650 x approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-

1650 laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. Drawer

fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal

construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening.

Pedestals are provided with lock for security, including snake/junction, etc.

The Back Unit shall be of dimensions 1650 x 500 x 750mm. It shall be made of 25mm thick MDF – one side pre-

laminate board confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. The Slide door unit is

made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

2 Back Unit thick PVC lipping. Shutters have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Nos 1 53,714.82 53,714.82

Storage is provided with lock for security , including snake/junction, etc.

Worktop shall be made of 25MM thick Pre-Laminated Board. All the edges of work surface shall be provided with

machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. Worktops are available either with Grommet or

Access flap cutouts. Provision for wire management provided on return side. Legs is fabricated from combination of 1.2

mm, 2 mm thk CRCA (as per IS: 513), 3mm, 5mm thk HR (as per IS: 2062) which has a triangular shape. MOdesty

3 Table Type 2 shall be Metal leg made from 1.2 mm thk CRCA. Cross members in the system are made from 50 mm x 25 mm x Nos 7 48,449.09 339,143.65

1.2mm thk. Wire management shall contain Wire Tray with integrated power box. Wire tray with integrated power box

made with a combination of 0.6 mm thk CRCA outer body and 0.8 mm thk , including snake/junction, etc.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back

outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which

is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanism shall be Active BioSynchro Mechanism. The mechanism of chair shall have following features:360

degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of

variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The

chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall

be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be

65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in

black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. The neckrest assembly consists of upholstered neckrest inner(material-poly

propylene) with moulded polyurethane foam and polyster fabric. upholstered inner shall be fixed to neck rest cover.

neckrest shall be fixed to back assembly through neckrest spline. Overall dimensions of Chair shall be, Width of Chair -

75.0cm, Depth of Chair - 75.0 cm as measured from pedestal below. Height from ground - min 109.3 to max 124.4 cm.

Seat height - min 45.5cm to max 55.5cm. Dimensions tolerance / variations shall be within +/- 1 cm.

The cushioned seat assembly shall consists of seat outer(material-30% glass fiber nylon) and upholstered seat

inner(material-polypropylene) with moulded polyurethane foam and polyster fabric. the net back should made up of back

outer(material-glass fiber filled nylon) and back inner(material-PP) and upholstered using polyester mesh fabric with

high tenacity yarn. Size of back shall be (W)-46.5cm, (H)-60.0cm & size of seat shall be (W)-51.0cm x (D)-49.0cm. The

supprot spine should made up of high pressure die cast polished aluminium. Armrest is having two adjustment,

Height(6+/-0.5cm) and depth(6+/-0.5cm). Height adjustment shall be provided in aluminium structure of armrest which

is connected to aluminium back spine and is operated with button. Armtop is made up of PU molded over plastic inner.

The mechanim shall be Active Bio Synchro Mechanism. The mechanism of chair shall have following features:360

degree revolving type, Seat/Back tilt ratio of 1:2, Active Bio-Synchro mechanism, 5 position tilt limiter giving option of

variable tilt angle to the chair. Front-Pivot for tilt with feet resting on ground and continious lumber support should

5 Visitor Chair Type- 1 ensure more comfort. The mechanism housing should made up of HPDC Aluminium and black powder coated. The Nos 16 24,777.98 396,447.74

chair shall be provided with pneumatic height adjustment which shall have stroke of 10.0 +/- 0.3 cm. The pedestal shall

be made of die-cast polished aluminium. it shall be fitted with 5 nos twin wheel castor. The size of the pedestal shall be

65.0 +/- 0.5 cm pitch-centre-dia (75.0 +/- 1.0 cm with castors). The twin wheel castors shall be injection moulded in

black polypropylene. The lumbar support assembly should consists of lumber spine(material-glass fiber filled nylon)

which is fixed to Aluminium back spine. Overall dimensions of Chair shall be, Width of Chair - 70.5cm, Depth of Chair -

70.5 cm as measured from pedestal below. Height from ground - 99 cm. Seat height - 49 cm. Dimensions tolerance /

variations shall be within +/- 1 cm.

Providing and Placing in place of 120 degree workstations of following specifications. The system shall be a desk-based

system with a platform understructure made up of a combination of MS. Tubes and plates. The terminating leg structure

shall be in M.S. CRCA sheet/ tubes/rods finished with epoxy power coating of the approved colour as per the project

designer. The terminating legs can be provided with modesty panels optionally. These modesty panel shall be of Metal

1.2 mm thick CRCA. The legs shall be provided with translucent glide screws to take care of the levelling as per the site

requirements. Worktop shall be made of 25MM thick Pre-Laminated Board. All the edges of work surface shall be

provided with machine pressed 2 mm thick PVC lipping glued with hot melt EVA glue. The worktop shall be complete

with provisions for screen mounting as well as for wire management on the workstation. Provisions for fixing of the

switches shall be on the wire tray/channel. Wire riser leg or independent wire risers shall be provided as per the layout

6 Workstations Nos - -

structure. Screen shall be provided as per the requirement of the design and layout. The screen finishes can be selected

from Fabric, laminated coloured glass, and DL marker board. Fabric screens shall be of 19 mm overall thick, Glass

screens are of 8 MM thick. The screens provided shall be complete with its set of PDC clamps for fixing on the worktop.

The screens shall be placed along the width of the worktop. The overall size of the worktop shall be 1350mm W1 x

1350mmW2 x 600mmD. Height shall be 1200mm. It shall be provided along with a Pedestals with legs- pedestal flat

metal front, free standing central locking of size 390 mm w x 435 mm d x 646 mm height 3dr = 2box+1file., including

snake/junction, etc.

Team Leader Size- 1350mmW x 600mmD x 1200mmH.

Workstations 120 120 degree workstation size- 1200mmW1 x 1200mmW2 x 600mmD x 1200mmH.

The seat shall be made of injection molded plastic outer and inner. Plastic inner shall be upholstered with fabric and

moulded polyurethane foam of density 67+/-2kg/m ³, and hardness load 16+/-2kgf as per IS:7888 for 25% compression.

The back shall be made 3.5+/-0.03cm x 1.5+/-0.02cm x 0.2+/-0.016cm of MSERW oblong tube. It shall be upholstered

using net fabric with high tenacity yarn. The dimensions of seat shall be- 46.0cm(W) x 48.0cm(D) and of back shall be

43.0cm(W) x 60.0cm(D). The armrest top shall be moulded from polyurethane and mounted on to a drop lift adjustable

type tubular armrest support made of dia 3.81+/-0.03cm x 0.2+/-0.01 cm thick MSERW tube. Armrest height adjustable

upto 6.5+/-0.5cm in 5 steps.. The mechanism of the chair shall have following features : 360⁰ revolving type, Active Bio-

synchro mechanism, Tilt tension adjustment, 5-position tilt limiter giving option of variable tilt angle to the chair.

Workstation Chair / Seat/Back tilting ratio of 1:2. The chair shall be provided with pneumatic height adjustment which shall have stroke of

Reception chair 10.0 +/- 0.3 cm. Seat depth adjustment shall be integrated in the seat through a sliding mechanism. Seat depth

adjustment range shall be 6.0+/-0.5cm. Back frame shall be connected to the Up/Down mechanism housed in plastic T

spine. it can be adjusted in the range of 7.42+/-0.5 cm for the comfortable back support to suit individual need. The

pedestal shall be injection moulded in black 33% GF Nylon66. it shall be fitted with 5 nos twin wheel castor. The size of

the pedestal shall be 66.1+/- 0.5 cm pitch-centre-dia (76.1 +/- 1.0 cm with castors). The twin wheel castors shall be

made of PP. Overall dimensions of Chair shall be, Width of Chair - 76.1cm, Depth of Chair - 76.1 cm as measured from

pedestal below. Height from ground - min97.3 to max 114.8 cm. Seat height - min 43.6cm to max 53.6 cm.

Dimensions tolerance / variations shall be within +/- 1 cm.

The overall size of the wortop shall be 3000mm x 1150mm x 740mm. Worktop shall be made from 25mm thick MDF

one side prelaminate board with 0.4mm PVC membrane pressed on to top and having chamfered edge. Soft closing

dual access flap provided for access to power supply and data cables. The Under-structure consists of mixture of 25mm

and 18mm Pre-laminated twin board of E1-P2 grade and approved shade conforming to IS-12823:1990, Edge banded

with matching 2 mm thick PVC lipping. Anodised aluminium alloy 63400 - WP profile is added at bottom edges for

10 Meeting Table improving the aesthetics.The product has a knock-down construction. A wire raiser made of 0.8mm CRCA MS IS:513. It Nos 1 115,544.35 115,544.35

is epoxy polyester powder coated (DFT 40-60 microns) for flow of wires and cables. A Power box with 2 cutouts on

either sides for standard 8 module Anchor Roma is provided. Beside each cutout, an additional cutout with plate is

provided for mounting Audio Visual Cables(eg. HDMI,VGA-A,etc), including snake/junction, etc..

The seat is made up of insert moulded Polyurethane Foam upholstered with foam laminated mesh fabric. The insert

moulded foam is assembled over a load bearing plastic seat cover. The back is made up of two piece injection moulded

frame. The inner frame is upholstered with mesh fabric and mounted on the main assembly. The back has adjustable

lumbar support for achieving comfortable seating posture. Sub Assembly Seat size = 52.5 cm Width, 51 cm Depth. Sub

Assembly Back size= 48.5 cm Max Width, 62 cm Ht. Effective Back Ht from Seat = 57 cm. The polyurethane foam for

seat is moulded with density = 75 ±4 kg/m 3 and Hardness = 34 ± 4. The armrest top is injection moulded in polyurethane and

mounted on the injection moulded height adjustable type armrest. The armrest height is adjustable up to 4.5cm in 3 steps & width

adjustable. ArmTop Out to Out Dim = 62 to 65 cm ArmTop centre to Centre Dim = 53 to 56 cm. The mechanism is designed with the

Meeting Room Head

11 following features:- 3600 revolving type. - Single point control. - Front pivot for tilt with feet resting on ground ensuring more comfort.- Nos 1 37,778.05 37,778.05

Chair Tilt tension adjustment. - 3position locking with antishock feature. The spine bracket is made of Aluminium diecast piece connecting

back with mechanism. Neck rest assembly is made of polyurethane foam upholstered with foam laminated mesh fabric. The neck rest

assy is mounted on the top of back. It can be adjusted up to 45mm up–dn and has angular adjustment of 30°. The pneumatic height

adjustment has an adjustment of 8.5 cm. Pedestal is made of Die cast Aluminium fitted with 5 nos. twin wheel castors (castor whee

ldia. 6.0 cm). The pedestal is 65.0cm. Pitch center dia. (71.0 cm with castors). The twin wheel castors are injection moulded in

Nylon. The overall size of the chair shall be 76cm x 76cm x (117cm-132cm).

The cushioned seat assembly shall consists of insert moulded polyurethane foam upholstered with foam laminated

mesh fabric. the insert moulded foam is assembeled over a load bearing plastic seat cover. The back shallmade up of

two piece injection moulded frame. The inner frame shall be upholstered with mesh fabric and mounted on the main

assembly. Size of back shall be (W)-48.5cm, (H)-62.0cm & size of seat shall be (W)-51.0cm x (D)-52.5cm.armrest shall

be injection moulded with height adjustable up to 4.5+/-0.5cm in 3 steps and width adjustable up to 20mm. The

mechanism of chair shall have following features:360 degree revolving type, Front pivot Synchro mechanism, Tilt

tension adjustment, 3 position tilt limiter with Anti-Shock feature. Spine bracket shall made of Aluminium diecast piece

Meeting Room connecting back with mechanism. Neck rest assembly shall made up of polyurethane foam upholstered with foam

12 laminated mesh fabric. The neck rest assembly is mounted on the top of back. it can be adjusted up to 4.5+/-0.5cm up- Nos 8 34,579.78 276,638.21

Revolving Chairs

down and has regular adjustment of 30 degree +/-2 . The chair shall be provided with pneumatic height adjustment

which shall have stroke of 9.0 +/- 0.3 cm. The pedestal shall be made of die-cast polished aluminium. it shall be fitted

with 5 nos twin wheel castor. The size of the pedestal shall be 66.0 +/- 0.5 cm pitch-centre-dia (76.0 +/- 1.0 cm with

castors). The twin wheel castors shall be injection moulded in black nylon. Overall dimensions of Chair shall be, Width

of Chair - 76.0cm, Depth of Chair - 76.0 cm as measured from pedestal below. Height from ground - min 100.0 to max

109.0 cm. Seat height - min 45.0cm to max 54.0cm. Dimensions tolerance / variations shall be within +/- 1 cm.

Supplying and placing of chair of dimensions 635W x 630D x 800H mm. The seat height shall be 455mm.The back shell

shall be made of 15mm plywood panle connected using Brackets made from 3mm Hot Rolled Steel Plates . Steel

brackets are Epoxy Polyester Powder Coated. 25mm PU Slab -Stock foam is pasted onto both sides of the shell and

pinched together to achieve the radius along the periphery. It shall be upholstered in Leatherette. The seat cushion shall

Reception Soft be made using 50mm PU Slab-stock foam and is upholstered in Leatherette. It shall be held in place with Hook and

Seating Loop tape stitched to its bottom side. The understructure shall be made of seasoned Tewak Wood finished witrh clear

matt coat of PU Lacquer. Undrstrucutre members shall be glued together using Epoxy Resin Based Adhesive. The shell

is fixed to the understructure using Alloy steel hardware (blackened and coated with rust preventive oil).

Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS 202 grade for fixing

Reception Center with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per IS:1762. overall

14 dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm., including snake/junction, etc. Nos 1 11,203.81 11,203.81

Poviding Storage Units. The overall dimensions of it shall be 1200 x 450 x 1200mm. It shall be made from Pre

laminated Particle board of 25mmm and 18mm thickness with 0.8mm thick CRCA metal cladding from outside. Side

metal cladding is coated with Epoxy polyster powder of 50 microns. It shall be provided with 11mm thick bent metal tops

15 Storages made of 0.8mm thick CRCA. In case of HDU, the doors are made from 18mm thick Pre laminated particle board with Nos 14 31,353.17 438,944.35

decorative laminate on one side and backing laminate on other. Uniformly distributed load capacity of each shlef is 40

kg maximum. Back panels are made from 18mm thick PLB. Locking mechanism shall be 3 way nickel plated woodren

furniture lock. Handles shall be of Aluminuium extrusion.

Main Body: (a) Construction: Rigid Knock Down construction made of 0.8 thk. CRCA Steel. Each unit has 5 loading

levels formed by 4 nos. adjustable shelves. The body comprises the following components: Front Cover: It is the

foremost panel of the body on which the Drive unit are fixed. It is made of 0.8 thk. CRCA Steel. The front cover has a

pattern of holes on the front surface for ventilation purpose. Back Cover: It is the backmost panel of the body and is the

mirror image of the front cover. It is made of 0.8 thk. CRCA Steel. The back cover has

a pattern of holes on the surface for ventilation purpose. Back Panel: The back panels are made of 0.6 thk. CRCA Steel.

The two back panels are fixed together using machine screws. When the entire optimizer layout is locked it also

prevents access to inside files

from the outside. Shared Panel: The shared panel acts as a partition between two adjacent bodies. It is made of 0.8 thk.

CRCA Steel. Optimizer Height from ground is 2083 mm (1980 body + 65 undercarriage + 38 channel system). Overall

size of one bost shall be 1200mm W x 400mm D. The bodies including shelves are given antirust surface treatment &

are coated with epoxy polyester powder. It involves an 8-step treatment. Final finish consists of epoxy polyester powder

coating of approved color & shade with a Dry Film Thickness of minimum 40 microns. Shelf: It is made of 0.7 thk CRCA

steel conforming to IS: 513 Gr.D or DD. Its max load bearing capacity is 100 Kg uniformly distributed per shelf. Shelves

are mounted on support brackets & shelf level can be adjusted at approx. 25.4 pitches. Storage capacity:- The shelf is

1180mm in length and can hold up to 13 nos. of box files of size 85mm x 345mm x 285mm. Drive Type Understructure:-

Providing and placing 3 seater sofa of following specifications. Size- 1860mm x 850mm x 880mm. Understructure:

Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of

cross sections 22x64mm,34x64mm and 16x35mm without having major knots & defects on the surface. Complete

understructure of Seat is made by gluing, nailing & stapling. Non-woven fabric of 100GSM is stapled on the top surface

after attaching Zig-Zag spring to cover the structure. Seating surface is made by using pocket spring of wire dia 2mm

which is surrounded by PU foam of density 28 kg/m3. A top layer of supersoft PU foam with density 32 kg/m3 is used to

17 Sofa 3 seater provide softness. Upholstery cover of seat is made of woven fabric. Polypropylene leg (with 20% talc for better filled with Nos 1 43,896.16 43,896.16

M8 steel stud in black color. Understructure of armrest is made up of combination of pinewood members, 12mm thick

Plywood, 3mm thick MDF. Pinewood are of cross sections 16x79mm without having major knots & defects on the

surface. Complete understructure of Armrest is made by gluing, nailing & stapling. Foam: Foaming of Armrest is done

with density 28kg/m3 and 60kg/m³.

Providing and placing 1 seater sofa of following specifications. Size- 770mm x 850mm x 880mm. Understructure:

Understructure of seat is made up of combination of pinewood members and 12mm thick Plywood. Pinewood are of

cross sections 22x64mm,34x64mm and 16x35mm without having major knots & defects on the surface. Complete

understructure of Seat is made by gluing, nailing & stapling. Non-woven fabric of 100GSM is stapled on the top surface

after attaching Zig-Zag spring to cover the structure. Seating surface is made by using pocket spring of wire dia 2mm

which is surrounded by PU foam of density 28 kg/m3. A top layer of supersoft PU foam with density 32 kg/m3 is used to

18 Sofa 1 seater provide softness. Upholstery cover of seat is made of woven fabric. Polypropylene leg (with 20% talc for better filled with Nos 2 36,008.90 72,017.79

M8 steel stud in black color. Understructure of armrest is made up of combination of pinewood members, 12mm thick

Plywood, 3mm thick MDF. Pinewood are of cross sections 16x79mm without having major knots & defects on the

surface. Complete understructure of Armrest is made by gluing, nailing & stapling. Foam: Foaming of Armrest is done

with density 28kg/m3 and 60kg/m³.

SCHEDULE OF QUANTITIES - HVAC WORKS

DSR VRV AND NON-DSR

S. No. DESCRIPTION UNIT QUANTITY RATE DSR (INR)

VRF 2019 (INR)

Supply Installation, Testing & Commissioning of modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable

for cooling and heating, having all hermetically sealed inverter type Scroll

Compressor(s), minimum two compressors for above 14 HP modules,

microprocessor based Controller, top discharge type condensing unit(s), with R

410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as

1 1 required. The unit shall deliver the rated capacity at AHRI Conditions and work per HP 30.00 16415.00 492450.00

even at 50°C ambient temperature without tripping. The unit shall be suitable to

work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled

with first charge of the refrigerant and ready for use as required. The COP at

AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

Supply,installation,testingandcommissioningoffollowingminimumcapacity4-

wayflowVRV/VRFCassetteType Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter,fan section with low noise fan/dynamically

balanced blower,multispeed motor,coilsection with DXCoppercoil, electronic

expansion valve,outercabinet, drainpump,grill,necessarysupports,

vibrationisolation,cordless remote control etc.,suitable for operation on single

2 2.0 phase230V±10%,50HzACsupply,complete,asrequired.The unit shall have

automatic force shut down provision in case offireon receiving signal from BMS

System.The cooling capacity of indoor unit will beat air inlet conditions of 27

Degree CD Band 19Degree CWB temperature.

Supply,installation,testing and commissioning of following minimum capacity

VRV/VRF High wall type Indoor unit equipped with washable synthetic media

pre-filter,fan section with low noise fan/ dynamically balanced blower, multi

speedmotor ,coil section with DX copper coil, electronic expansion valve, outer

cabinet ,cordless remote control,drain pan,necessary accessories etc., suitable

3 3.0 for operationon 230V±10%, 50Hz, single phase AC supply,complete as

required. The unit shall have automatic force shutdown provision in case of fire

on receiving signal from BMS System.The cooling capacity of indoor unit will be

at air inlet conditions of 27Degree C DB and 19 Degree C WB temperature.

Lifting, Shifting, Supply, Installation, Testing & Commissioning of

Interconnecting "Y" & "T" Joints i.e. Refnet Joints/Header with Insulation

for refrigearnt piping

5 5 Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and

Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant

piping for VRV/VRF system, complete with fittings, with suitable adjustable ring

type hanger supports, jointing/brazing including accessories, insulated with

XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile

rubber tubular sleeves sections of specified thickness as given below for

Suction and Liquid lines, all accessories as per specifications etc. as required :

5.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick m 150.00 245.00 36750.00

5.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick m 300.00 331.00 99300.00

5.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick m 150.00 466.00 69900.00

5.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick m 10.00 588.00 5880.00

5.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick m 10.00 707.00 7070.00

5.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick m 10.00 865.00 8650.00

5.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick m 10.00 1022.00 10220.00

5.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick m 10.00 1108.00 11080.00

6 Cable/Wiring

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FRLS PVC insulated copper conductor, single core cable in surface/ recessed

medium class PVC conduit as required.

DSR (E & M - Cable Trays with Covers

Supplying and installing following size of perforated Hot Dipped Galvanised Iron

cable tray (Galvanisation thickness not less than 50 microns) with perforation

4.6 not more than 17.5%, in convenient sections, joined with connectors,

suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc.

4.6.8 300 mm width X 62.5 mm depth X 2.0 mm thickness meter 20.00 1085.00 21700.00

35 4.6.10 450 mm width X 62.5 mm depth X 2.0 mm thickness meter 20.00 1440.00 28800.00

8 Drain Piping

Supply,installation,testing and commissioning of PVC drain water with

MR necessary clamps, fittings such as bends tees etc. and duly insulated.

9 DISMANTLING, LIFTING, SHIFTING OF EXISTING SYSTEM

DISMANTLING, LIFTING, SHIFTING OF EXISTING SYSTEM complete with NOS 10.0 4500.00 45000.00

M.R. cabling, insulation, and other materials as required complete in all respect as

per the directions of the engineer in charge.