REPAIR/ MAINT TO FLOOR, PLASTERING, TILING, ROOFING, AC SHEET WITH FALSE CEILING, ROOF TREATMENT, JOINERY AND CERTAIN OTHER CONNECTED B/R WORK IN ZONE B AT OLD CANTT ALLAHABAD.

Amount

Demolition of cement oncrete (un reinforced) of any description and in any position not secifically provided, complete all as specified and directed.

Demolition of reinforced cement concrete as in chajja and similar type works, complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises, complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc., laid, bedded in any mortar, complete all as specified and directed.

Taking down cement plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water including removing of all rubbish off from the site, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 300mm x 300mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 300 x 200 x 5 to 6mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:4, complete all as specified and directed.

Glazed ceramic coloured tiles as in vertical surface of walls such as skirting / dado and risers to steps, size of tile shall be 450 x 300 x 6 to 7mm thick, set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match the colour or shade of tiles, laid over and including provison of 10 mm thick rendering as in backing coat of tiles in cement mortar 1:4, complete all as specified and directed.

Non - skid Ceramic, coloured tiles 7 to 8 mm thick, size of each tile shall be 400mm x 400mm, as in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, laid over and including provision of 15 mm thick screed bed in CM 1:6, complete all as specified and directed.

Non skid ceramic coloured tiles 400mm x400mm x 7 to 8 mm thick, in skirting, dados, risers to steps, etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4), complete.all as specified and directed.

Virified Ceramic tiles 9 mm thick (square/ rectangular) polished, 600mm x 600mm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in CM (1:6) complete all as specified and directed.

Virified Ceramic tiles 9 mm thick (square/ rectangular) polished, 600mm x 600mm, in skirting, dados, risers to steps, etcskirting, dados, risers to steps etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over and including 10 mm thick rendering in CM (1:4), complete.all as specified and directed.

Pre-polished rubber moulded smooth finish, exterior, designed, pre-cast interlocking tiles/ pavers, 60 mm thick, over 25mm thick sand cushioning, complete all as specified and directed.

Exterior Heavy duty full body coloured paving tiles of size 300mm x 300mm x 8 to 9 mm thick, in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match tiles over and including 15 mm thick screed bed or bedding layer in CM (1:6), complete all as specified and directed.

Machine Cut Granite 20 mm thick table rubbed and polished counter top, cooking plateform bedded & jointed with grey cement slurry and pointed with white cement mixed admixture of pigment to match the shade of granite including cutting, polishing and moulding edges including 15 mm thick screed bed or bedding layer in CM (1:6), complete all as specified and directed.

Machine cut baroda Green marble stone slab 18 to 20 mm thick laid over Kitchen cooking platform in 20 mm thick cement screed mortar (1:6) laid and jointed in grey cement slurrry mixed with pigment to match the shade of the slab including cutting, rubbing and polishing complete and including nosing of the edges half round (stone slab shall be fixed in two piece), complete all as specified and directed.

Machine cut Kota stone slab 18 to 20mm thick, flooring over and including 20 mm thick screed bed in cement mortar 1:6, laid and jointed in grey cement slurry mixed with pigment to match slab including rubbing and polishing mirror finish, complete all as specified and directed.

Machine cut kota stone 18-20 mm thick over 10 mm thick bedding layer CM (1:4) in riser of steps, skirting, pillar etc laid and jointed in grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

Cement concrete 1:3:6 type C-1 using 20 mm graded stone aggregate in plinth protection, 50 mm thick, finished even and smooth without using extra cement, including making joints 12mm wide to the full depth of PCC at the length n exc 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete all as specified and directed.

PCC 1:4:8 type D-2 using 40 mm graded aggregate, 75 mm thick, as in sub base of floor etc complete all as specified and as directed.

Cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregate in floors, 40 mm thick, laid in panels fixed with glass dividing strip and finished even & smooth without using extra cement complete all as specified and directed. Note: Glass dividing strip shall be measured and paid separately.

Supply only Glass dividing strips, 3 mm thick and 38 mm wide, inserted in position in floors, complete all as specified and as directed.

Plain cement concrete 1:2:4, 100 mm thick, type B-2 (using 40mm graded crushed stone aggregate) as in floor, (laid in alternate panels) including use and waste of form work finished even and smooth without using extra cement, complete all as specified and directed.

Precast reinforced cement concrete as in cover slabs (for manholes) chullah hoods, chajjas, water trough, mangers, shelves and other similar works, type B-1, 1:2:4 using 20 mm graded agg. set in cement mortar 1:4, complete all as specified and directed. Note: Reinforcement to be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and directed.

Brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, complete all as specified and directed.

Brickwork with sub class 'B' bricks, straight or curved on plan exceeding 6 metre mean radius, built in CM 1:6, complete all as specified and directed. [Except brick]

Rendering 15 mm thick, on brick work or concrete surface in cement mortar 1:4 as in drain, boundary wall etc finished even and fair, complete all as specified and as directed.

Rendering 15mm thick in CM 1:4, mixed with water proofing compound, on brick work or concrete surfaces of walls, finishing the surface even and smooth without using extra cement, complete all as specified and directed. Note: Water proofing compound shall be measured and paid separately.

Rendering 15mm thick in CM 1:6 on faces of brick work or concrete surfaces of walls, finishing the surface even and fair, complete all as specified and directed.

Rendering 5mm thick in CM 1:3 on concrete surfaces of ceilings, finishing the surface even and fair, complete all as specified and directed.

Supply only integral water proofing compound, complete all as specified and directed.

Plain Cement concrete 1:2:4, type B-1 (20 mm crushed stone aggregate) as in roof kerb, mud stop, gola, rounded or chamfered on edges, complete all as specified and directed.

Cleaning the sunken floor surfaces by wire brushes, brooming, removing dust, including dismantling of floor, lime terracing and applying following :- (a) Bitumen primer confirming to IS-3384-1965 @ 0.50 kg per sq.m. (b) Applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg/sq.m confirming to IS – 702-1998 for water proofing membrane. (c) Applying of polymeric water proofing membrane weight not less than 3 kg / sq.m over entire area with overlaps and sealed all as specified and directed. (d) Again applying a tack coat of hot blown bitumen 85/25 @ 1.2 kg / sq.m over water proofing membrance. (e) Dusting dry sand @ 0.75 kg per sq.m over water proofing membrane. (f) Fixing of GI pipe spout 50mm of adequate size, complete all as specified and directed.

Plain cement concrete type E-2, 1:5:10 (using 40mm graded stone aggregate), as in mass concrete in sunken floors., complete all as specified and directed.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal to store, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed.

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 15mm bore of pipe, complete all as specified and directed. [Except tubing]

GI tubing medium grade, galvanised with all fittings including short lengths, fixed to ceilings and walls with and including provision of suitable size of clamps or laid in floors, complete with all fittings (such as bends, elbows, Tee, short pieces, connectors, back nuts, diminishing pieces, caps, plugs and unions etc.,), 20mm bore of pipe, complete all as specified and directed. [Except tubing]

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 500 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair,complete all as specified and directed.

Rotational moulded HDPE water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, ISI marked, double layered hoisted and fixed in position including connecting up pipes including ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair, complete all as specified and directed.

Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe 20 mm bore, fixed in repair, complete all as specified and directed.

Ball valves, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball, screwed for iron pipe and fixed for 20 mm bore size (minimum weight 210gms), fixed in repair, complete all as specified and directed.

PVC (SWR) 75 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, fixed in repairs, complete all as specified and directed.

PVC (SWR) 110 mm bore pipes single socketed ends, in any length with rubber ring joints, fixed to walls, fixed in repairs, complete all as specified and directed.

PVC (SWR) bends, ISI marked of any radius of 75 mm bore pipes jointed with rubber solvent, fixed in repairs, complete all as specified and directed.

PVC (SWR) bends, ISI marked of any radius of 110 mm bore pipes jointed with rubber solvent, fixed in repairs, complete all as specified and directed.

PVC (SWR) 75 mm dia, junction single, (single T), equal or unequal with oval access door fixed to PVC pipe joint with rubber solvent, fixed in repairs, complete all as specified and directed.

PVC (SWR) 110 mm dia, junction single, (single T), equal or unequal with oval access door fixed to PVC pipe joint with rubber solvent, fixed in repairs, complete all as specified and directed.

Stack clamps out of 50 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for fixing of 110 mm pipe, complete all as specified and directed.

Stack clamps out of 50 mm by 5 mm flat iron and iron stays, including bolts and nuts and securing ends of stays to wall or roof for fixing of 75 mm pipe, complete all as specified and directed.

PVC (SWR) floor trap, 75mm size, plain with grating including joining with solvent cement concrete 1:2:4, type B-1 (using 20 mm graded crushed stone aggregate) complete all as specified and as directed.

Stainless steel plate rack / utensils rack of size 600mm x 750mm x 250mm depth made out ot 0.63mm thick stainlesss steel sheet, fixed to wall with brass scres including provision of necessary fittings / fixtures viz., nuts, bolts and washers of suitable size, the plate shall conform to the sample kept in sample room of AGE Fort Cantt, fixed in repair, complete all as specified and directed.

Kitchen Sinks with drainage board made of stainless steel 1 mm thick in kitchen or laboaratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including cantilever brackets of mild steel angle 35 mm x 35 mm x 5 mm, 32mm dia brass waste coupling, 32 mm dia PVC waste pipe (rigid quality) and connecting union to pipe overall size 915 mm x 460 mm, bowl size 410 mm x 330 mm x 160 mm, fixed in repair, complete all as specified and directed.

Angle cock, fancy type, cast copper alloy, screwed down, high pressure, with capstan head, screwed one end for iron pipeand other for PVC connmection and fixed 15mm bore, fixed in repairs, complete all as specified and directed. Make:- Jaquar, Prayag, Cera

Stop valves, cast copper alloy, fancy type, chromium plated (concealed type), with chromium plated wall flange, screwed down, high pressure, long shank and exposed part kit with fitting sleeve, operating lever concealed part, screwed both ends for iron pipe or for unions and fixed, 15mm bore, fixed in repairs, complete all as specified and directed. Make:- Jaquar, Prayag, Cera

Bib taps (fancy type), cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule and fixed, 15mm bore, fixed in repairs, complete all as specified and directed. Make:- Jaquar, Prayag, Cera

Grating round 100 mm dia of stainless steel, fixed in repair, complete all as specified and directed.

Grating round 150 mm dia of stainless steel, fixed in repair, complete all as specified and directed.

Pillar taps cast copper alloy with capstan head chromium plated fancy type screwed down high pressure with or without lettered 'HOT' or 'COLD' letter with long screwed shank and fly nuts, screwed for iron pipe 15mm bore pipe, complete all as specified and directed. Make:- Jaquar, Prayag, Cera

Brass chromium plated shower rose 65 to 90 mm size with swivel joints, fixed in repair, complete all as specified and directed.

PVC low level cistern ‘white’ with inlet, 10 litre capacity, float valve including bracket with 32mm dia PVC pipe 600 mm long, fixed in repair, complete all as specified and directed.

PVC connection, 15 mm size, 600 mm long, with brass fly nut at both end, fixed in repairs, complete all as specified and directed.

PVC waste pipe of 32 mm dia, flexible for wash hand basin or urinals, fixed in repairs, complete all as specified and directed.

PVC waste pipe of 40 mm dia, flexible for wash hand basin or urinals, fixed in repairs, complete all as specified and directed.

Vitreous china squatting pan, ‘Orissa’ pattern, of size 580 mm x 440 mm white with integral foot rest complete including provision of cement concrete bedding and connection to trap, outgoing flushing pipe, anti syphonage pipe, CI trap 100 mm Bore of pipe etc, fixed in repairs, complete all as specified and directed.

Vitreous China wash hand basin white flat back of size 550 mm x 400mm fixed on cantilever brackets of mild steel a 32mm dia brass waste coupling, pedestal type, fixed in repairs, complete all as specified and directed.

Vitreous China wash down water closet (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), fixing seat cover including connection to drain (or outgoing pipe, and to flushing pipe & antisyphonage pipe etc) with CP mild steel hinging device, fixed in repairs, complete all as specified and directed. Note :- Plastic seat cover shall be measured separately as supply only as considered under respective items.

Supply only Plastic water closet seat, white closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device, complete all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area exc1.5 Sqm but n. exc 4 Sqm each and removing from site, complete all as specified and directed.

Taking down chowkat or frames with shutters (without taking off shutters from the frames) area n exc 1.5 Sqm Each and removing from site complete all as specified and directed.

Taking down shutter of any description not exceeding 1 Sqm each complete all as specified and directed.

Taking down shutter of any description exceeding 1 sqm but not exceeding 2 Sqm each complete all as specified and directed.

PCC 1:3:6 type C-1 (using 20mm crushed stone aggregate) as in fixing of hold fasts with and including provision of necessary form work if required complete all as specified and directed.

Mild steel work as in wind ties, hold fast etc, confirming to Fe 290 Gde E-165, complete all as specified and directed.

Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc including door frames, cooler stand, gate and door shutter, etc, conforming to Fe 410-W (Gde-E- 250) quality-A, complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification, complete all as specified and directed. MAKE:- Sintex / Rajshree plastic / Wood Forex, Indore / M/s Kumar Arch Tech Ltd.

Glazed and skeleton shutters, 35mm thick, second class hardwood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), divided into squares with plain, chamfered or rounded mitered beads for securing glass/gauge complete all as specified in SSR Pt- I, section 8, clause 8.24(a) and as directed. Note: Glass or wire cloth, etc. in panels or sash squares shall be measured and paid separately.

Flush shutters 32 mm thick, factory made, solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Aluminium sliding door bolts, 250 mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified and directed.

Aluminium anodised, barrel tower bolts of extruded section and fixed, 150mm long, complete all as specified and directed.

Butt hinges, 100 mm long, medium weight, cold rolled mild steel, complete all as specified and directed.

Butt hinges, extruded aluminium alloy with brass/ bronze hinge pin, anodised and fixed, type B-21, 100mm long, bright polished type B-11, complete all as specified and directed.

Aluminium alloy handles, cast type, anodised, 150mm long, complete all as specified and directed.

Aluminium anodised hasp and staple, 150mm size, fixed in repair, complete all as specified and directed.

Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete, 300mm size, fixed in repair, complete all as specified and directed.

MDF board 18 mm thick, interior grade, prelaminated one side with decorative type lamination including wooden/ PVC beading, fixed in repair, complete all as specified and directed.

Steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete with glazing bars, dovetailed or welded joint, fixed in repair, complete all as specified and directed..

Steel window factory made with side hung shutter including box type hinges with steel handle, steel peg stay, complete without glazing bars, dovetailed or welded joint, fixed in repair, complete all as specified and directed..

Steel ventilator with top hung shutter including hinges, steel peg stay handles lugs incl guard bars, glazing bars, fixed in repair, complete all as specified and directed.

Aluminium (diecast) body hydraulically door closer regulated,designation No.3, universal type,sutable for door shutters of 851 mm to 1000 mm in width and weight between 61 to 80 Kg, fixed in repair, complete all as specified and directed.

Taking down aluminium door shutter from frame exceeding 1.0 Sqm but not exceeding 2.0 Sqm and re-fixing in same opening after repair of parts such as clip, easing, rubber beads, greasing/ oiling and including replacement of components i.e. middle rail, top rail and handle complete with locking arrangement, replacement of floor door spring for smooth functioning complete all as specified and directed NOTE: The unit quoted rate deemed to include all spare part for smooth functioning of door and any claim won't be entertained on this account.

Aluminium door (powder coated) single leaf with anodized aluminium frame of section 47.62 x 44.45 x 1.88 mm thick, shutter with bottom & middle rail of section 100 x 44.5 x 2 mm thick and styles & top rail of section 85 x 44.5 x 1.56 mm thick with centrally locking arrangement with lock make of ‘GODREJ’ or ‘LINK’ 7 lever and floor door spring hydraulically regulated including jointing cleats, fixing of 02 Nos of 150mm long aluminium handle & 02 Nos of 150mm tower bolt and glazing with 5.5 mm thick ordinary plain glass including necessary fittings, fixtures & aluminium snap beads, fixed in repair, complete all as specified and directed.

Aluminum window (powder coated) with aluminum anodized frame of aluminum section 47.62 x 44.45 x 1.88 mm thick with shutters having styles & rails of aluminum section 47.62 x 44.45 x 1.62 mm thick including jointing cleats, glazing clips, rubber packing, aluminum snap beading, screws anodized aluminum fittings such as hinges, 02 Nos tower bolts, 02 Nos handles etc including 5.5 mm thick ordinary plain glass complete. Including providing and fixing aluminum chequered grill of anodized section of mesh 100 x 100mm of 08 mm dia of bar fixed to frame with 20x205 mm aluminum flat with screw, fixed in repair, complete all as specified and directed.

Aluminium partition frame work anodized frame of size 62.5 x 37 x 1.5 mm thick with bottom & middle rails of aluminium section 62.5 x 37 x 1.5 mm thick and styles, top of section 62.5 x 37 x 5.5 mm thickincluding jointing cleats, filled with 12mm thick pre- leminated partical board intrerior grade up to middle rail from bottom and 5 to 6 mm thick plain/ frosted glass in balance portion secured with aluminum fillet of size 20mm, including necessary fittings, fixtures, fixed in repair, complete all as specified and directed.

Aluminium grill Decogrill DG-117 with aluminium anodized/ powder coated mesh with Square tube (solid) 6 mm thick sheet, fixed in repair, complete all as specified and directed.

E-board Make: Everest, Design "Lake and Hill" of size 605mm x 605mm x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section (White powder coated). The framework shall comprise of main runner made from 0.33mm thick GS sheet and of size 24 x 32x 300mm and soaced at 1200mm maximum centres securely fixed to structural soffits with hangers of 2mm dia GI wire to be fixed with approved rawl plugs, adjusters and screws. Flush fitting of 1200mmm long cross Tee (with double stiching) to be interlocked between main runners at 600mm centre to form 1200 x 1600 mm modules cross tee longer than 600mm to be supported independently. 600 x 600mm doubles to be formed by fittings 600mm long cross tee centrally between the 1200mm cross tee. Perimeter wall angle shall be of 0.45mm thick GS sheet of size 19 x 19 mm and 300mm long of white colour all as per manufacturers instructions, fixed in repair, complete all as specified and directed. Make of frame work: Armstrong or equivalent.

E-board Make: Everest, Design "Lake and Hill" of size 605mm x 605mm x 4mm thick white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on old / existing frame work all as per manufacturers instructions, fixed in repair, complete all as specified and directed.

Dismantling of AC corrugated or semi corrugated sheet including AC ridges as in roof or wall covering, complete all as specified and directed..

Asbestos cement corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed.

Asbestos cement corrugated sheet, 6 mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed. [Expect sheet]

Asbestos cement two piece adjustable plain wing ridge, 6mm thick, fixed with ‘L’ type or ‘J’ type or cranked hook bolts, complete all as specified and directed.

Prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa, as in roof covering / cladding to wall fixed with welf tapping screws, fixed in repair, complete all as speified and directed .

Prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of colour having tensile strength of 550 Mpa, as in roof covering / cladding to wall fixed with welf tapping screws, fixed in repair, complete all as speified and directed .

Dismantling of timber scantlings 40 sq. cm and over in unframed work in any position, complete all as specified and directed.

Second class hard-wood clean sawn in scantlings as in timber framed, complete all as specified and directed.

Second class hard-wood clean sawn in scantlings as in timber framed, complete all as specified and directed. [Expect timber]

Preparing surfaces of wood and wood based materials, new or old, of any description and girth, not otherwise described and treated with creosote oil, complete all as specified and directed.

Framed work such as grills, gratings, etc.. with ends of bars shouldered and / or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, and similar work conforming to Fe-290 Gde-E-165, complete all as specified and directed.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple, complete all as specifed and direcetd.

Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, in repair, complete all as specifed and direcetd.

Hacking out old broken glass (any thickness, size, quality or description) from metal/ wooden frame, complete all as specifed and direcetd.

Sheet glass, 4mm thick, ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Sheet glass, 4mm thick, frosted on one side ordinary quality and glazing in squares not exceeding 0.5 sq. m in each pane with oil putty, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc, conforming to Fe 410-W (Gde- E- 250) quality-A, complete all as specified and directed.

Stainless steel drapery rod cut to size and fixed in position including brackets, 25 mm dia, fixed to wall, fixed in repair, complete all as specified and directed.

Cleaning of HDPE tank of capacity up to & including 500 Litres by flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 metre and depositing complete all as specified and directed.

Cleaning of HDPE tank of capacity exc 500 Litres but n exc 1000 ltrs by flushing out water cleaning & removing of sludge, scale mud etc from wall & floor by rubbing with brushes, cleaning with caustic soda etc complete & finally washing with fresh water, including writing date of cleaning with white synthetic enamel paint and removing sludge, scale mud etc to a distance not exceeding 50 metre and depositing complete all as specified and directed.

Preparation of new wooden surfaces exc 10 cm width or girth with sand or emery paper & applying two coats of synthetic enamel paint over a coat of pink primer , complete all as specified and directed.

Preparation of new steel and iron surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Preparation of new plastered surfaces of walls and applying two coats of acrylic emulsion paint of approved colour over a coat of chalk whiting, complete all as specifed and directed.

Preparation of new plastered or unplastered surfaces of ceilings and applying three coats of white wash, complete all as specifed and directed.

Mild Steel handle (left or right) for steel window of existing size including necessary welding / riveting etc. fixed in repair, complete all as specified and directed.

Spot welding in repair to butt hinges/ single action spring hinges/ double action spring hinges/ projecting type hinges/ box type hinges by welding the same to existing door frame/ mild steel window frame, 100/ 75mm size, complete all as specified and directed.

PVC Covers for PVC water tanks of capacity 500 litres /1000 Litres, fixed in repair, complete all as specified and directed.

Brass spindles of No 1, 2 & 3 for CP bib taps, complete all as specified and directed.

Rubber Door Seal with length of each door seal equal to width of door fixed to door bottom rail including all fixing arrangement such as screw, nails, etc. fixed in repair, complete all as specified and directed.

Sink coupling of 40mm size/ wash hand basin coupling 32mm size, complete all as specified and directed.

Preparation of old decorated plastered surfaces of walls including cornices, pilaster etc., by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of acrylic emulsion paint of approved colour, complete all as specified and directed.

Preparation of old decorated plastered surfaces of walls including cornices, pilaster etc., by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying one coat of cement base paint of approved colour, complete all as specified and directed.

Preparation of old decorated plastered surfaces of ceiling including cornices, pilaster etc., by brooming down or steel wire brushing, scraping down smoke soot, moulds, moss and efflorescent salt, greasy spots and applying one coat of white wash, complete all as specified and directed.

Toughened glass 12mm thick, as in hinged doors, partitions, automatic doors and similar work including cutting to shape, drilling holes required including all necessary fittings such as verticle handles, stainless steel angles, screws, etc, complete all as specified and directed.

Ram Babu Bros

HARSH ASSOCIETES

MS BHAVANA ENTERPRISES

M/S Akhilesh Enterprises

M/S ATUL CONSTRUCTION

M/S Garg Sons

M/S SANJAY CONSTRUCTIONS

AMARDEEP ENTERPRISES

R K GUPTA AND SONS