SPECIAL REPAIR OF BLDG NO T-247 (OFFR MESS) OF 17 RAJPUT AND PROVN OF 01 X SPLIT AIR CONDITIONER, 2 TON WITH STABILIZER SYSTEM ROOM OF COMN COMPLEX OF 118 (I) INF BDE GP SIG COY AT NIMU MIL STN UNDER AGE (I) NIMU

Amount

Demolition of precast concrete block walling masonry, built in cement mortar

M&L for Pre-cast cement concrete block masonry in cement concrete 1:3:6 type C1(using 20mm graded aggregate) with solid blocks, exc. 10 cm in width and setting in mortar 1:4 complete all as specified.

M&L for Non - skid coloured Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. over 15mm thick Screed bed or bedding layer of mortar 15 mm thick for laying floor finishes in CM 1:4 over an including 25mm thick under layer of PCC 1:2:4 to bring the work in proper levelling set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified.

M&L glazed ceramic tile " coloured" 450mmx 300mm x 7mm as in verticle surface such as skirting /dado etc, set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the shade of tile, fixed over and incl 10mm thick bedding layer in cement mortar 1:4 on concrete block wall surface complete all as specified.

Dismantling floor, hearth or wall tilling including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish of the premises

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

TMT bars 10 mm dia and above, cut to length , bent to shape required including cranking , bending spirally for hooping for columns, hooking ends, binding with and including mild steel wire ( annealed ) not less than 0.9mm dia , complete all as specified and directed by Engr-in-Charge.

M&Lfor RCC1:2:4 ( Nominal Mix) (20mm graded crushed stone agg) as in Slabs supported on walls, beams and columns in floors,roofs, landings, balconies,shelves and the like

Dismantling wrought iron or mild steel work of any description not otherwise provided for

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L painting on steel surface over 10 cm width or girth including preparation of surface and applying two coats of synthetic enamel paint over a coat of red oxide primer.

Taking down chowkhats or frames exc 1.5 sq. m but n exc 4 sq.m each (without taking off shutters from the frame)

Taking down Shutters of any description exc 1 sq. m each but n exc 2 sq. m each

M&L for 2nd class Hardwood Plain, solid, straight chowkats and frames, wrought, rebated on the solid,, rounded or chamfered, put together with glue pinned at joints,

M&L for 30mm thick shutter, 2nd class Hardwood, Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for ecuring glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, SSR Part I, Section 8 clause 8.24(b) as in windows & ventilators;

M&L for 35mm thick 2nd class Hardwood, Plain, framed, Panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats

S&F 125 mm long Butt hinges, medium weight, cold rolled mild steel

S&F for exruded aluminium alloy handles, 150mm size, fabricated type, anodised

S&F 200mm long, Aluminium anodised, barrel tower bolts of extruded section

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy

S&F for 5.5mm thick Sheet glass, ordinary quality and glazing with beads in square n exc 0.5 sq. m in each pane

M&L for preparation of new wooden surfaces of any description over 10cm in width or girth and applying two coats of S/E paint over a coat of pink primer.

Dismantling wall and ceiling boards(fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness including cover fillets.

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with nails to timber frame work as in Ceiling

S&F 9mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination,fixed with nails to timber frame work as in walls all as specified and directed.

Dismantling timber scantling as in fillets, rails, posts, rafters, purlinf, etc under 40 sq.cm in section in any position as in unframed work.

M&L for 2nd class soft wood of sectional area exc 13 & n.exc 25 sq.cm in plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads.

M&L for 2nd class soft wood of sectional area exc 3 & n.exc 6 sq.cm in bullnosed, splayed, chamfered or rounded on one or both edges or face and wrought as in beading all as specified and directed by Engr in charge.

M&L for 2nd class soft wood of sectional area exc 6 & n.exc 13 sq.cm in bullnosed, splayed, chamfered or rounded on one or both edges or face and wrought as in beading all as specified and directed by Engr in charge.

M&L for fix in repair 18/19mm thick Particle board, medium density, flat pressed,single layer type or three layer type with BWR type adhesive, fixed with nails to timber frame work

M&L for 0.9mm thick ,Decorative laminate type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions

S&F 75mm Butt hinges, cast brass, with mild steel hinge pin, bright polished and fixed, type B-12

Demolition of Stone slabs and tiles of any description laid, bedded and pointed in in any mortar or thickness in floors, aprons etc.

M&L for 20mm thick Granite (of any type) tiles machine cut, bedded including Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 for laying finishes and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory, with plug, waste pipe, washers, including cantilever cast iron brackets, connecting union etc.overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm

S&F in repair15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified.

S&F in repair for 15mm PVC connections of 600mm long with PTMT nuts complete all as specified.

S&F in repair 15mm dia Angle cock/Stop valves, cast copper alloy,screwed down, high pressure,with crutch or butterfly handle,screwed both ends for iron pipe or for unions and fixed complete all as specified

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15cm thickness (belowor above ground level)

M&L for 75mm thick Cement concrete type C- 2,1:3:6 (40mm graded aggregate) as in plinthe protection

Taking down or up steel tubing and connections incl cleaning for refixing or removal to store for 15 mm dia bore.

S&F for 25mm outer dia 3-layer PP-R P o l y p r o p y l e n e random copolymer) concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded p o l y p r o p y l e n e random fittings fixed complete to walls, ceilings or in floors etc.

Dismantling broken water tank of cap exc 500 ltr but n exc 1000 ltr

S&F for 1000 ltr cap Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I

PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or floor of 75mm bore pipe complete all as specified and directed by Engr-in-charge

PVC (SWR) floor trap of 75mm plain with grating including jointing with solvent cement

M&L for 100mm thick cement concrete 1:3:6 type C2 bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested complete all as specified and directed by Engr-in-charge

S&F BALL VALVE 25mm dia complete all as specified and directed by Engr-in-charge

S&F 25mm Nipple suitable for HDPE water tank (Minimum weight 20mm-45 gms

Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of internal dia 75-100mm incl any earth work and demolition of PCC complete all as specified and directed.

Taking down carefully aluminium point wiring light, fan socket or power complete fitting such as switches, ceiling rose, fan regulator, socket including light fitting etc complete with /PVC /MS conduit and T/W battern / casing caping and all as specified and as directed by Engineer-in-Charge.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminimum conductor of size 16 Sq mm twin core, served with inner sheathing of PVC tape and overall PVC sheathed in service connections, flat or circular all as specified and directed by Engineer-in-Charge .

M&L in repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :- (a) One light point/one fan point controlled by one switch

M&L in repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :- (b) One 3 pin 5 amps socket outlet independent with cables 1.5 sqmm size

M&L in repair for point wiring with PVC insulated single core cable of stranded copper conductors of size 1.5 sqmm, 1100 volt grade drawn in and including rigid PVC casing caping accessories lain on wall/ceiling surface and fixed with PVC saddles and back-plate and GI screws, including PVC insulated single core cable of stranded copper conductor of size 1.5 sqmm as earth continuous wire connected to common earth and PVC Board for housing like switches, sockets, fan regulators etc all as directed by Engineer-in-Charge for following :- (c) One 3 pin 5 Amp socket outlet on same board.

All same as per item No 54 above but with conductor of size 4 sqmm (Nominal area) for one 3 pin socket outlet 15 Amps on independent board complete and earth continuity wire with 4 sqmm PVC insulated stranded copper conductor Cable.

S&F Socket 2 in 1, 5 pin 5 Amp flush type complete all as specified and directed by Engr In Charge.

S&F Switch piano flush type 5 Amp, single pole, one way complete all as specified and directed by Engr in Charge.

S&f Switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete all as specified and directed by Engr in Charge .

S&F Switch Socket Combination 2 in 1, 3 pin, 15/16 amp flush type Universal complete all as specified and directed by Engr in Charge .

M&L for ceiling rose surface Bakelite 65x50mm two to three terminal complete all as specified and as directed by Engr-in-Charge.

S & F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed by Engr in Charge.

Supply and Fixing indoor LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr in Charge.

S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 10 watt, 2 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.(Havells Cat Pt No. - LHEXACP7IN1W010 or equivalent in Philips/Crompton)

S&F basic all purpose surface and wall mounted LED batten with polycarbonate housing and integreted electronic driver of cap 20 watt, 4 feet long, with all accessories complete all as per specified and as directed by Engr-in-Charge.(Havells Cat Pt No. - LHEXAXPNIN1W020 or equivalent in Philips/Crompton)

S&F sheet metal powder coated versatile Double door SPN distribution board, 12 way suitable for MCB's fitted with copper bus bar rated 200amps, neutral link , earth bar and din rail suitable for use on 240 Volt, 50Hz with all accessories complete all as per specified and as directed by Engr-in-Charge. .

M&L for MCB SPN 63 Amp, 240V with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as per specified and as directed by Engr-in-Charge.

S&F to MCB SP 6-32 Amp with 10KA breaking capacity of 'C' series in distribution boards with all accessories complete all as per specified and as directed by Engr-in-Charge.

Dismantling and Taking down old u/s street / building sequrity Light fittings from poles, flood lights, post top lantern lights and garden lights for replacement with LED fittings all as specified and as directed by Engr in Charge.

Supply and fix in Repair LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection completepecified and directed by Engr in charge.

M&L for GI bracket 1.5 mtr long made out of GI pipe 40mm dia bend to suitable radius incl clamps nuts bolts washers incl painting with aluminum paint etc complete all as specified and directed by Engr in charge.

Supply and fix exhaust fan, steel body AC single Phase. 230V with, blades, and frame and louvers of size 450 mm sweep heavy duty all as per specified and as directed by Engr-in-Charge.

M & L for Earthing complete with galvanised steel earth plate electrode of size (600 x 600 x 6.3) mm thick buried directly into ground vertically to depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, surrounded on all sides by alternate layers of 150 mm thick charcoal and common salt, connected to MS galvanized earh strip of size 25 x 4 mm by means of lugs, bolts, nuts, washer, check nuts of galvanised iron or steel all as shown in Electrical plate No. 3, wire protected by dia 15 mm bore light grade GI Pipe laid in floor and fixed to wall with proper size of clamps and watering pipe of bore 20 mm dia GI light grade including wire mesh funnel, PCC, earth chamber pit with PCC 1:2:4 type B-1 using 20 mm grade stone aggreate including form work cement mortar including CI Pit cover with frame necessary excavation and earth work in any type of soil including testing on completion for desired result all as specified.

Supply and install high wall split units indoor/ outdoor complete with cordless remote control unit and with in built Heating and Cooling arrangement and Digital Inverter twin rotary of capacity 02 TR with fittings, drain pipe etc as reqd at site.

Supply and fix 5 KVA capacity Voltage stabilizer, copper wounded suitable for 2 TR split AC, automatic operation, single phase naturally air cooled indoor type & designed for input variation between 170 V to 250 V with output voltage stabilized at 230 V with accuracy of ± 2.5% and speed of correction 8V per second, fixed on wall with necessary arrangements complete all as specified and directed by Engr in Charge.

S & F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20A, 240V and connecting complete all as specified.

S & F for submain wiring with 2 runs of single core 4 sqmm PVC insulated copper conductor cable FR, ISI marked alongwith 1 run of 4 sqmm copper conductor cable as earth continuty conductor drawn through and including PVC Casing Caping of suitable size concealed. Note : 3 Runs of PVC wires of 4 sqmm and one run condit will be measured as one unit).

S&F 240V, 10 KA, 'B' curve MCB of single pole and current carrying capacity 25 Amp, in MCB DB complete with connection testing and commissioning

M/S ASGAR ALI TIMBER SHOP (BID ID -3430920)

osho traders (BID ID -3431104)

M/S Behl Sons (BID ID -3430948)

M/S GEE AAR and SONS ENTERPRISES (BID ID -3431169)