Day to day maint to address emergency complaints of leakage/seepage, cleaning of service tanks and connected works at Fort Cantt Prayagraj.

Amount

Dismantling / taking down 15 mm dia bib cock / stop cock/Pillar Cock/Angle cock etc of any pattern or of any type and re-fixing the same after minor repairs such as replacement of washers and major repair such as jumper brass, spandle/ caps etc or refixing old serviceable bib cocks/ stop cocks/ pillar cock/angle cock any pattern complete all as specified and directed. Note - Any major parts such as spindles to be measured as supply only in conjuction with this item and paid for accordingly) Note : Spindle of CP Bib cock/ stop cock/ pillar cock/ concealed cock will be paid as supply only under respective item.

Supply only spindle brass for 15 mm dia CP Bib cock/ pillar cock/ concealed cock of any pattern complete all as specified and directed.

Attending daily complaints like leakge of bib taps, angle valve stop cocks or in all types of CP/PVC fittings, GI pipes fitting and similar work for continuity of essential internal water supply services by employing an experienced team of plumbers and helpers to restore after repair/ replacement to the satisfaction of Engineer-in-Charge. All as directed T&P for attending the job will be provided by the contractor.

Note for Srl Item No. 3 above :- (i) T&P including convence to reach door to door for attending the jobs will be provided by the contractor. (ii) The complaint slip will be collected from complaint cell incharge/JE(Civ) by the contractor or auth rep in writing. (iii) Each complaint shall be attend on same day and will be resolved within 48 hours otherwise contractor shall be liable to pay a panelty of Rs. 50/- per unresolved complaint per day subject to maximum Rs.1000/- per unresolved complaint. (iv) The area/Location of of Job will be all MD and OTM accn in AOR of OD Fort Cantt. (v) Rate are including labour fixed in repairs for removing / repairing or replacement. Relevent items shall be paid seprately as Supply only under respective items.

Attending daily complaints related to carpenter work and obtaining completion from user including repair/easing of doors re-fixing or tightening of doors, windows, resecuring of door/window wire guage, builders hardwares, helical door spring including use of all types of nails, screws etc which are required to make good the work, use of any other stores/fittings shall be paid seprately under Supply only items in building to continuity of essential carpentry service by employing a team of experienced carpenters with a helpers to restore the existing service to the satisfaction of Engineer-in-Charge. All as directed T&P for attending the job will be provided by the contractor.

Note for Srl Item No. 4 of BoQ :- (i) T&P including convence to reach door to door for attending the jobs will be provided by the contractor. (ii) The complaint slip will be collected from complaint cell incharge/JE(Civ) by the contractor or auth rep in writing. (iii) Each complaint shall be attend on same day and will be resolved within 48 hours otherwise contractor shall be liable to pay a panelty of Rs. 50/- per unresolved complaint per day subject to maximum Rs.1000/- per unresolved complaint. (iv) The area/Location of of Job will be all MD and OTM accn in AOR of OD Fort Cantt. (v) Rate are including labour fixed in repairs for removing / repairing or replacement. Relevent items shall be paid seprately as Supply only under respective items here in after.

Cleaning of PVC service/ over head tank of capacity up to & including 500 Litres process are as under (a) Dewatering using submerssible pump/bailing out of water to dispose the minimum level of dirty water from the tank. (b) Cleaning the tank inside walls, bottom, ceiling of tank using high pressure water jet to dislodge the algae calcinations, dirt etc. (c) Disposing the dirt water sludge etc., using specially designed sludge removal pump. (d) Cleaning the tank inside throughly by using industrial grade vaccum pump to make the tank inside free from dirt, algea and sludge etc. (e) Treating the inside walls, bottom, ceiling of tank including all nooks and corners by using and spraying anti bacterial agent such as hydrogenperoxide (bio degradable) for disinfection of tank inside. (f) Total disinfection and sterlisation of tank hyginecally cleaned and bacteria free and safeby Eco-Friendly for storage of water. (g) The area/Location of of Job will be all MD and OTM accn in AOR of OD Fort Cantt. Note :- Date of cleaning to be written over head tank after cleaning.

Cleaning of PVC service/ over head tank of capacity exceeding 500 Litres up to 1000 ltrs process are as under (a) Dewatering using submerssible pump/bailing out of water to dispose the minimum level of dirty water from the tank. (b) Cleaning the tank inside walls, bottom, ceiling of tank using high pressure water jet to dislodge the algae calcinations, dirt etc. (c) Disposing the dirt water sludge etc., using specially designed sludge removal pump. (d) Cleaning the tank inside throughly by using industrial grade vaccum pump to make the tank inside free from dirt, algea and sludge etc. (e) Treating the inside walls, bottom, ceiling of tank including all nooks and corners by using and spraying anti bacterial agent such as hydrogenperoxide (bio degradable) for disinfection of tank inside. (f) Total disinfection and sterlisation of tank hyginecally cleaned and bacteria free and safeby Eco-Friendly for storage of water. Note :- Date of cleaning to be written over head tank after cleaning.

M&L for Removing of vegitation growth cutting of shrubs plant or tree of girth not exc 30 cm incl roots from wall and roof of bldg,mouth of rain/waste water pipe for building height upto 15 mtr including necessary scaffolding works, cutting of wall/roof etc to remove complete root of vegetations and applying chemical blue vitriol at the root of vegetation and making good the damaged portion with CM 1:3 or PCC 1:2:4 & two coats of cement base paint etc complete all as specified and directed by Engr-in-charge. Note:- (a) The area/Location of of Job will be all MD and OTM accn in AOR of OD Fort Cantt.

Supply only cover for over head PVC water storage tank of capacity 500/1000 ltrs rotating type including frame including nut bolt complete.

Supply only 20 mm dia Gun metal, globe or gate valves, with iron wheel head,screwed both ends for iron pipes complete.

Supply only 15 mm dia Gun metal, globe or gate valves,with iron wheel head,screwed both ends for iron pipes complete.

Supply only 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 g ms) complete.

Supply only in 15 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe (Minimum weight 210 g ms) complete.

Supply only 15-20mm (out side dia-20 mm) GI reducer complete.

Supply only 20 mm bore GI Union complete.

Supply only 20 mm bore GI Elbow complete.

Supply only 20 mm bore GI socket complete.

Supply only 15 mm bore GI Tee complete.

S&F 15 mm bore GI Union complete.

Supply only 15 mm bore GI Elbow complete.

Supply only 15 mm bore GI socket complete.

Supply only 15 mm bore 150 mm long Nipple

Supply only 15 mm bore 100 mm long Nipple

Supply only GI nipple fully threaded with two numbers check nuts and washers for PVC tank, 100mm long to PVC tank with back nut and washers for inlet and outlet pipe of size 15 mm bore complete.:

Supply only GI nipple fully threaded with two numbers check nuts and washers for PVC tank, 100mm long to PVC tank with back nut and washers for inlet and outlet pipe of size 20 mm bore complete.:

Supply only 15 mm size bib taps cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed for iron pipes complete.

Supply only 15 mm size bib taps PTMT type any colour high pressure screwed for iron pipe and fixed(Min weight 15mm-90gms) complete.

Supply only 15 mm size pillar taps PTMT type any colour high pressure screwed for iron pipe and fixed (Min weight 15mm-110gms) complete.

Supply only pillar tap cast copper alloy with capstin heads chromimium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete.

Supply only 15 mm size angular cock, cast copper alloy, chromium plated, fancy type with capstan head, screwed down, screwed both end for iron pipes complete.

Supply only stop valve, 15 mm chromium plated with long shank and cup (Concealed type) both ends for iron pipe complete.

Supply only CP Swivel shower for fixing with 15mm pipe complete.

Supply Only Brass chromium plated shower rose 125 mm size complete.

Supply only CP Shower arm 15 mm size, with flange fixed to wall complete.

Supply only PVC flexible waste pipe 32 mm dia and over for fixing in urinals and wash basin ,kitchen sink complete .

Supply only waste coupling of 32 mm size chromium plated for glazed ware wasg hand basins, etc with long screwed shanks and fly nuts flanges complete.

Supply only waste coupling of 40 mm size brass chromium plated for sink , etc with long screwed shanks and fly nuts flanges end bedded in red lead cement and other end fixed complete.

Supply only PVC Jet for EWC complete set including 15 mm long complete.

Supply only in flush handle PVC with adjustable lever and hook for low level flushing cistern complete.

Supply only in PVC syphon complete for low level flushing cistern complete.

Supply only 10 ltrs PVC (White) valve less syphonic action type, flushing cistern low level with inlet ball valve float, handle, aluminium brackets for bottom support including gitties etc complete.

Supply only 450 mm long PVC connections 15 mm size with PTMT nuts at both end complete.

Supply only 600 mm long PVC connections 15 mm size with PTMT nuts at both end complete.

Supply only plastic water closet seat cover white closed pattern with flat bottom and cover incl mild steel chromium plated hinging devices complete.

Supply only of Brass chromium plated 15mm wall mixer valve 3-in-1 for mixing hot and cold water, fancy type complete.

Supply only Health faucet of superior quality ABS body with 15 mm dia 1.25 m long flexible tube and wall hook complete.

Supply only toilet paper holder with flap recessed type chromium plated complete.

Supply only Single Lever Basin Mixer with 450 mm long braided hoses complete.

Supply only brass chromium plated Tumbler holder complete.

Supply only angle cock, 2 way, with wall flange 15 mm dia complete.

Supply only Towel Rack 600 mm long with lower Hangers complete.

Supply only Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete.

Supply only 250 mm size Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) ISI marked and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete.

Supply only 100mm long hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete.

Supply only 100mm size aluminium anodised handle, fabricated type complete.

Supply only 150 mm long aluminium anodised handle, fabricated type complete.

Supply only 100 mm long Aluminium anodised barrel tower bolts of extruded section complete.

Supply only 150 mm long Aluminium anodised barrel tower bolts of extruded section complete.

Supply only 200 mm long Aluminium anodised barrel tower bolts of extruded section complete.

Supply only 300mm size mild steel rat tail rod pattern door springs ISI marked including roller & roller plate etc complete.

Supply only 100 mm size 4-lever mild steel mortice lock vertical type with two keys etc complete.

Supply only floor door stopper of Aluminium anodised body and tounge anodised with hard drawn steel spring of cover plate length of 150 mm size complete.

Supply Only aluminium die cast body Door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete.

Supply only 250 mm size mild steel peg stay fixed to steel window complete.

Supply only mild steel handle for steel window etc complete.

Supply only Stailness steel plate rack of size 910mm x 780mm x 250mm (31'' x 36 " 10") with separators and 3 tier shelves, provisionsing of hook 9 Nos made out of stailness steel sheet of grade AI SI 304 complete.

Supply only Cabinet Mirror PTMT 450 x 555 mm with sided shelves fancy type of superior quality (Product Dimension(Lxbxh)(Mm): 450W X 124D X 555H complete.

Supply only Corner glass shelf superior quality matt finished crromium plated (MCH/Colour CP ) with bracket and fittings complete.

Supply only stainless soap dish complete.

Supply only soap dish ,matt finished chromium lated (MCH/Colour) complete.

Supply only glass shelf matt finished chromium plated (MCH/Colour CP) (Chrome, Wall Mounted) bracket and fittings complete.

Supply only PVC fiber sheet shelf 450x125 mm with bracket complete.

Supply only PVC fiber sheet corner shelf complete.

Supply & Fix in repair Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F in repair sinks without drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specifiedand directed.

S&F in repair Sinks with drainage board made of stainless steel l mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supply and fixing 500 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old tank complete all as specified and directed.

Supply and fixing 1000 liters capacity white colour triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc and including 20 mm size Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete and including dismantling of old tank complete all as specified and directed.

Supply & Fix in repair mild steel tubing of 25 mm dia with PVC coating for curtain rod fancy type including fancy type PVC rings and brackets (wall to wall or flush to wall) for securing to curtain rod complete all as specified and directed.

Supply & Fix in repair 25 mm dia stainless steel drapery rod cut to size and fixed in position including brackets, cap both end fixed to wall complete all as specified and directed.

Supply & Fix in repair Door Seal length of each door seal is equal to width of door fixed to door bottom rail including all fixing arrangement such as screws nails etc complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated etc) sheets in roof covering complete all as specified and directed.

M & L for 6 mm thick asbestos cement, corrugated or semi- corrugated sheets in roofs, walls etc fixed with ‘j’ & ‘L’ hooks or cranked bolts and washers complete all as specified and directed.

M & L asbestos two piece adjustable serrated ridge for corrugated or semi corrugated sheets fixed with ‘J’ hook or cranked bolts complete all as specified and directed.

Demolition of Concrete of any description and in any position not otherwise specifically provided for as in sunken floor etc complete all as specified and directed.

M & L for Providing, cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate as in coping, coving, roof padding, padding in sunken slab as directing mixed with liquid water proofing compound complete all as specified and directed.

M & L for PCC 1:7:12 type F2(using 40 mm graded stone aggregate) as in filling into sunken floor complete all as specfied and directed.

M & L for Providing 25 mm thick, cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate in flooring in sunken slab complete all as specified and directed.

M & L for Treatment to sunken floor and sides as mentioned here after:- (Step-I) Cleaning of RCC surface to remove existing treatment to sides and base slab by using sand blasting with compressed air. (Step-II) M&L application of a coat to sides and base of sunken with glass fibre reinforced acrylic modified cementitious coating system with base coat of Sika Top & Seal -107 @ 1.50 Kg/Sqm glass fibre reinforcement Sika Fab-I and top coat with Sika Seal-107@ 1.50 Kg/Sqm or equivalent of Forsoc or pidilite. (Step-III) M&L 15 mm thick cement plaster on side and base slab of sunken part in cement mortar 1:3 mixed with appropriate integral water proofing compound with Sika Plastocree plus as specified. (Step-IV) M&L applying evenly a tack coat of industrial bitumen 85/25 @ 1.20 Kg/Sqm on plastered surface of sunken sides & base.Note:All debris obtained from site will be thrown away out side Def Land by contractor at his own expense. Note :- 72 hours ponding test shall be done and test results duly signed by AGE and user shall be submitted for claiming payment.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc) or insulation board/slabs/blankets/AC boards etc any thickness .

S & F in ceiling using 'E' board of size 605 mm x 605mm x 4 mm thick, white prelaminated set embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped galvanised iron imposed grid with 24mm wide T-section exposed flanges which shall be powder coated white. The frame work shall comprise of main runner made from 0.33mm thick galvanised steel sheet and of size 24mmx32mmx300 mm board spaced at 1200 mm maximum centre to centre. Hangers of GI wire 4mm dia to be fixed by approved rawal plug level and fasteners and screws etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall, flush fitting of 1200mm longer cross tee (with double stitching) to be interlocked between main runners at 600mm centre to centre from 1200x600mm modules cross tee longer than 600mm to be supported independently. 600x600mm doubles to be formed by fitting 600mm long cross tee centrally between the 1200mm cross tee.(with double stitching) to be interlocked between main runners at 600mm centre to centre from 1200x600mm modules cross tee longer than 600mm to be supported independently. Tee perimeter wall angle shall be 0.45mm thick GS sheet of size 19 mmx19 mm and 300mm long of white colour all as per manufacture's instructions compete all as specified & directed.

Material and Labour for Non - skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes over25 mm thick PCC 1:2:4 type B0 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

Material & Labour Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including incl 10mm thick plaster in cm 1:4 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

Material and Labour for Non - skid coloured eramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over Screed bed or bedding layer of mortar 10 mm thick for laying floor finishes over25 mm thick PCC 1:2:4 type B0 including dismantling of exsiting tiling/pcc floor/ wall any type and removing dubries outside of Md/OTM accn complete all as specified and directed.

S&F in repairs high density polythene pipe 32 mm (HDPE) of pressure @ 6 Kgf/Sqcm laid in trenches / wall complete all as specified and directed.

S & F in repair 75 mm dia PVC floor trap plain with grating including jointing with solvent cement complete all as specified.

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) area n.exc. 1.50 Sqm each and making good the disturbed surface complete all as specifiedand directed.

Taking down chowkhats or frame with shutter (without taking off shutter from the frame) area exc 1.50 Sqm and n.exc 4.00 Sqm each and making good the disturbed surface complete all as specified and directed.

Taking down shutters of any description exc 1.00 Sqm and n. exc 2.00 Sqm each complete all as specified and directed.

S & F Pressed steel frames factory made for doors out of 1.25 mm thick PBI sheet with one of more rebates including necessary flat iron lugs,hinges, lock strike plate, hinges etc complete, size of frame 105 x 60 mm including tarring ends and back of chowkats and lugs including back filling of PCC 1:3:6 for chowkats & PCC 1:2:4 for block for hold fast including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces all as specified and directed

S & F Pressed steel frames factory made for doors out of 1.25 mm thick PBI sheet with one of more rebates including necessary flat iron lugs,hinges, lock strike plate, hinges etc complete, size of frame 125 x 60 mm including tarring ends and back of chowkats and lugs including back filling of PCC 1:3:6 for chowkats & PCC 1:2:4 for block for hold fast including two coats of synthetic enamel paint over a coat of red oxide primer on exposed surfaces all as specified and directed

Material & Labour preparation of new wooden surfaces over10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer complete all as specified and directed.

S & F 35 mm thick factory made 2nd class Hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges offraming plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

Supply & Fix 35 mm thick 2nd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed

S & F 35 mm thick flush door shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S & F solid PVC door frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforcement with MS square tube supplying and fixing in opening as per specification & sketch shown in sketch 8 of SSR part II complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck indie with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fittied in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy complete all as specified and directed.

S & F 100 mm long hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified and directed.

S & F 200 mm size aluminium anodized barrel tower bolts of extruded section complete all as specified and directed.

S & F 150 mm long aluminium anodised handle fabricated type all as specified and as directed by Engineer-In-Charge.

Supply & Fix Steel windows/ventilator with tubular frame factory made with double shutter (wire gauged shutter & glass/glazed shutter, (wire cloth and glass panes shall be measured and paid separately) of size 79mmx39mm,16 gauge rectangular tubular frame with side hung shutter with glazing bars 12x3mm flat iron incl box type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal or wooden frame, glazed with putty or fixed with beads complete all as specified and directed.

S & F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty in Sqm n.exc 0.50 Sqm in each pane complete all as specified and directed.

S & F 3.00 mm thick Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 in each pane complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

Taking down Shutter exceeding 1.0 Sqm but not exceeding 2.00 Sqm each complete all as specified and directed.

Taking down Shutter exceeding 2.0 Sqm each complete all as specified and directed.

S & F 18 mm thick PVC celuka waterproof PVC Foam board made of polyvinyl chloride with features as waterprrof,flame ratardant acid and alkali resistant, light heat preservation pvc foam board in various colour duly fitted into the wall mount for kitchen cabinet, cupboard shutters, self etc complete all as specified and directed

S & F 100 mm aluminium anodised Hasp and staple, safety type, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F 75 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S & F continuous (piano) hinges, mild steel, bright finish or electrogalvanised having width of flap 30mm complete all as specified and directed.

Supply & Fix in repairs colour european type combination pattern WC casket type christinna with mounted flushing cistern ,pvc connection,seat cover and jointed to sewage pipe complete all as specified and directed.

S & F in repair Vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests including setting the trap and pan in concrete and including 10 ltr capacity PVC valveless syphonic action type low level flushing cistern and 32mm dia PVC Flush pipe complete including jointing to socket of flushing rim all as specified and as directed.

S&F in repair vitreous china wash hand basin with pedestal pattern white flat back size 550 x 400 mm excluding taps waste chain and plug but including bracket, waste coupling of 32 mm size fixed in repair complete all as specified and directed by Engineer-in-Charge.

Supply & Fixed in repairs vitreous china pedestal pattern (P Trap) type white wash down water closet pan with Antimicrobial Solid Seat Cover Code No.: C8094 but excluding flushing cistern and flush pipe complete all as specified and directed.

Supply & Fix in repairs vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 15mm bore pipe complete all as specified and directed.

Supply and Fix 15 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line all as specified and as directed by Engineer-in-Charge.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store 20mm bore pipe complete all as specified and directed.

Supply and Fix 20 mm bore galvanised steel water tubing, medium grade including necessary fittings such as GI bends, tee, union etc fixed on wall / floor complete and connecting to water supply pipe line all as specified and as directed by Engineer-in-Charge.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth of brick walls complete all as specified and directed.

Demolition of brick work or stone/ boulder Masonry, built in cement mortar including all quoins, pillars etc complete all as specified and directed.

M & L for Brick work with fly ash (old size) bricks, straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6.complete all as specified and directd.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

M & L for rendering 5 mm thick on ceiling surfaces in cement mortar 1:3 finished even & fair all as specified and directed.

M & L for rendering 10 mm thick on other than fair faces of walls of brick work or concrete surfaces in cement mortar 1:6 compound finished even and smooth without using extra cement complete all as specified and as directed.

M & L for Rendering 15 mm thick on fair faces of walls of brick work or concrete surfaces in cement mortar 1:4 with water proofing compound finished even and smooth without using extra cement complete all as specified and as directed. Note: water proofing compound shall be measured & paid seprately. Note: Where the items executed upto 12 mtr height, necessary scaffolding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. Green cloth shall be provided all around the work site for any position/height with all safety precaution (i.e. Safety Jacket, Safety Shoes, Safety Masks, Safety Helmet, Safety harness, Safety Goggles etc) Without safety precaution this work will not be commenced as decided by Engineer-in- Charge. NO extra cost shall be paid for such precaution. Such precaution shall be deemed to be included in the quoted rate.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L Preparation of newly plastered wall surfaces and applying two coats of distemper oil emulsion over one coat of birla white putty 1 mm thick preparatory to distempering complete all as specified and directed.

M & L for preparation of newly external plastered surfaces of wall and applying two coats of weather proof paint of APEX of Asian paints or its equivalent over a coat of white primer including applying 2mm to 3mm thick wall care putty all as specified and directed. Note: Where the items executed upto 12 mtr height, necessary scaffolding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. Green cloth shall be provided all around the work site for any position/height with all safety precaution (i.e. Safety Jacket, Safety Shoes, Safety Masks, Safety Helmet, Safety harness, Safety Goggles etc) Without safety precaution this work will not be commenced as decided by Engineer-in- Charge. NO extra cost shall be paid for such precaution. Such precaution shall be deemed to be included in the quoted rate.

M & L for complete removal of existing treatment on walls with electric operated blade, washing, rubbing down and stopping of plastered surfaces of wall and applying two coats of weather proof paint of APEX of Asian paints or its equivalent over a coat of white primer including applying 2mm to 3mm thick wall care putty all as specified and directed. Note: Where the items executed upto 10 mtr height, necessary scaffolding, props, jacks, shuttering and ladder shall be provided by the contractor in his own arrangement and the same is included in unit rates quoted. Green cloth shall be provided all around the work site for any position/height with all safety precaution (i.e. Safety Jacket, Safety Shoes, Safety Masks, Safety Helmet, Safety harness, Safety Goggles etc) Without safety precaution this work will not be commenced as decided by Engineer-in- Charge. NO extra cost shall be paid for such precaution. Such precaution shall be deemed to be included in the quoted rate.

M&L for preparation of old wooden surfaces of any description, not otherwise described over 10cm width or girth and applying one coat of synnthetic enamel paint of approved colour / shade complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described over 10 cm in width or girth and applying one coat synthetic enamel paint complete all as specified and directed.

M&L for preparation of old plastered surface and applying two coat of oil bound distemper on walls over a coat of primer and 1 mm thick wall care putty including complete removal of existing treatment complete all as specified and directed.

S&F in repair 110mm bore dia PVC (SWR ) vent cowl complete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) bends any radius with oval access door complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) bends any radius complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) bends with access door any radius ccomplete all as specified and directed.

S&F in repair 110 mm dia PVC (SWR) plain bends any radius complete all as specified and directed.

S&F in repair PVC (SWR) junction single T bore 110 mm complete all as specified and directed.

S&F in repair PVC (SWR) junction single T with access door bore 110 mm complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified and directed.

S&F in repair 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including all type earth work complete all as specified and directed.

S&F in repair PVC (SWR) 110 mm dia pipes single socketed, in any length with rubber ring joints, fixed on walls complete all as specified.

gangotri enteriprises (BID ID -3067276)

vs construction (BID ID -3067065)

M/S A P CONSTRUCTION (BID ID -3065728)

Airways Enterprises (BID ID -3061292)

shweta constructions (BID ID -3067500)