CERTAIN SANCTIONED SPECIAL REPAIR WORKS IN URI LINES, POONCH LINES, NAUSHERA LINES AND RAJOURI LINES AT DAMANA UNDER GE JAMMU

B/R Portion: - Demolition of cement concrete (unreinforced) of any description and in any position for roof, not otherwise specifically provided for and complete removal of debris outside MOD land complete all as specified and as directed.

Demolition of brickwork built in cement mortar including all quoins, arches pillar etc. complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floor and paving not exceeding 15 cm thickness below or above the ground level complete all as specified and as directed.

Demolition of cement concrete (reinforced) in roofs, beams, staircases, landing, chajjas and similar work complete all as specified and as directed.

Taking down cement plaster on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) not exceeding 1.5 Sqm each complete all as specified and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frame) exceeding 1.5 Sqm and not exceeding 4.00 Sqm each complete all as specified and as directed.

Taking down shutters of any description exceeding 1 Sqm and not exceeding 2 Sqm each complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15 mm bore dia steel tubing and connections, including removal to store/ site complete all as specified and as directed.

Taking up or down 20 mm bore dia steel tubing and connections, including removal to store/ site complete all as specified and as directed.

Dismantling timber scantling in fillets, rails, posts, rafters, purlins, etc. under 40 Sq.cm in section complete all as specified and as directed.

Dismantling asbestos cement (corrugated semicorrugated, etc) sheets in roof covering including L type or J type hooks or cranked bolts etc complete all as specified and as directed.

Dismantling water tanks and removing to store capacity of water tank exceeding 500 and not exceeding 1000 litres complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding, removing rubbish off the premises complete all as specified and as directed.

Dismantling PVC water tank/ demolition of RCC water storage tanks of capacity exceeding 250 but not exceeding 500 litres and removing from site complete all as specified and as directed.

Dismantling wooden framed roof truss not exceeding 10 m complete span all as specified and as directed.

Dismantling timber scantlings 40 Sq.cm and over in section and in any position complete all as specified and as directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified and as directed.

Removing existing treatment in any thickness from roof surfaces such as Coba treatment/ mud phuska, tarfelt, fungus, moss, dust etc., cleaning the surface of all foreign material by wire brushing and dusting and racking out RCC slab complete all as specified and removing the debris outside defence land and all as directed.

Hacking out old broken glass (any thickness size quality or description) from metal frame including punching or drilling out old glazing pins/ spring clips and providing and fixing new ones (including all necessary scaffolding, lifting arrangement up to 12 mtr height) complete all as specified and as directed.

Providing cement concrete (1:2:4) type B-0 (using 12.5 mm graded crushed stone aggregate) in roof padding, roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

Applying 10 mm thick plaster in cement mortar (1:4) including integral water proofing compound @ 3% by weight of cement on roof complete all as specified and as directed.

PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) as in bed block and coping, post hole and benching embedding of hold fast etc complete all as specified and as directed.

PCC 75 mm thick (1:3:6) type C-1 (using 20 mm graded crushed stone aggregate) plinth protection and sub base of chequered tiles etc. complete all as specified and as directed.

25 mm thick cement concrete (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in floor complete all as specified and as directed.

PCC 40mm thick (1:2:4) type B-0 (using 12.50mm graded crushed stone aggregate) in sub base for floor complete all as specified and as directed.

Reinforced cement concrete (nominal mix) (1:2:4) type B-1 (using 20mm graded crushed stone aggregate) lintel of door/ window, beams and columns in floors, slabs and in shelves etc. complete all as specified and as directed.

Brick work using sub class ‘B’ bricks old size, straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Description all as per Ser item No. 28.00 here-in-before but with old brick obtained from demolition (except brick) complete all as specified and as directed by Engineer-in-Charge.

Rolled section as in main and cross beams hip and angle, jack rafters, purlins where connected to common rafters and running rails and guides for vertical column and for sliding doors, fixed with angle cleats or other connecting plates etc including steel primer coat, welding, confirming to Fe-290 grade E-165 complete all as specified and as directed.

Framed work such as guard bars, grills, hold fast etc and similar work including welding/ rivetting confirming to Fe-290 Gde E-165 complete all as specified and as directed.

Framed work as in doors and gates of angle or other section including welding/ rivetting, stringers, braces etc complete drilled for fixing of steel sheeting or other coverings to doors etc conforming to FE-410-W complete all as specified and as directed.

Roof truss (framed) trussed, purlins, crane gantries, rails and fastening and heavy bracket framing (Beam, tee, angle, MS plates etc including steel primer coat, welding, distance pieces cleats etc confirming to Fe 290 grade E-165 complete all as specified and as directed.

TMT bars of 10mm dia and over, dia cut to length bent to shape required including cranking bending spirally, hooking ends and binding with mild steel wire not less than 0.9 mm dia (annealed) complete all as specified and as directed.

TMT bars of 5mm dia and over upto 10mm dia in stirrups, spacers and binders etc. complete all as specified and as directed.

Rendering 15mm thick on brick masonry/ RCC member surface in cement mortar (1:4) and finished the surface smooth and even without using extra cement including necessary scaffolding (upto 15M height) complete all as specified and as directed.

Rendering cement plaster 10 mm thick in cement mortar (1:3) on concrete surfaces as in ceiling and finished the surface fair and even without using extra cement complete all as specified and as directed.

15mm thick rendering in cement mortar (1:6) on concrete, brick/ stone surfaces of wall finished even and smooth complete all as specified and as directed.

Rendering 15 mm thick on concrete/ brick/ stone surface wall in cement mortar (1:4) finished fair and even, including necessary scaffolding complete all as specified and as directed.

Rendering 15mm thick in cement mortar (1:4) on fair faces of brick surface finished even and fair including water proofing compound complete all as specified and as directed. (Including all necessary scaffolding, lifting arrangement up to 12 mtr height).

Flat formwork to lintel beam, soffits, roof beams, lintels, cantilevers, shelves including supports, overhangs, etc. complete all as specified and as directed.

Cleaning of the exposed concrete slab and repairing the surface irregularities like cracks, potholes, as per manufacturer's method statement by Berger HS Rapairo (or equivalent) along with HS Latex Plus (or equivalent) and cement in mixing ratio of (1:4) where ever required complete all as specified and as directed.

Home Shield PU Roofkoat (or equivalent) is a one component liquid, solvent free, cold applied, waterproofing membrane that is highly elastic and UV resistant with 10 years Warranty. ASTM D 6083-97a Waterproofing and heat reflecting system having following key performance properties. (i) UV resistant, prevent yellowing and weathering. (ii) Highly elastic upto 350% and crack bridging. (iii) Excellent adhesion on porous and non-porous substrates. (iv) Tensile Strength >10 N/Sqmm with GeoTextile fleece. (v) Solar Reflective Index (SRI) more then 109-111 ASTM E 1980-11. System: First coat : Providing and applying primer over the prepared surface with HS PU roofkoat Primer (or equivalent), Coverage : 0.2Kg/Sqm (with 50% dilution of water), Reinforcement: Geotextile 40 gsm, Second coat: Home shield roofkoat (or equivalent), Consumption : 0.5 Kg/Sqm, Third coat: HS PU roofkoat (or equivalent), Consumption : 0.8 Kg/Sqm. System buildup -1.5Kg/Sqm with geotextile of 40 gsm complete all as specified and as directed.

Complete removal of existing treatment by means mechanical sander , water jet, grinder from walls , ceiling all as specified and directed by Engineer-In- Charge.

Applying two coats of oil emulsion distemper on ceiling new plaster surfaces including preparation, necessary scaffolding complete all as specified and as directed.

Applying two coats of oil emulsion distemper on old decorated ceiling surfaces including preparation and necessary scaffolding complete all as specified and as directed.

Applying two coats of cement based paint on new plaster surfaces including preparation, necessary scaffolding complete all as specified and as directed.

Applying two coats of cement based paint on old decorated surfaces including preparation and necessary scaffolding complete all as specified and as directed.

Preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior paint or apex (any colour) silicon based over a coat of water based suitable primering as a base course as per manufacturer's instructions complete all as specified and as directed.

Preparation, washing, rubbing down of old decorated plastered or un-plastered surface of wall and applying one coat of weather proof exterior paint or apex (any colour) silicon based over a coat of water based suitable primering as a base course as per manufacturer's instructions complete all as specified and as directed.

Applying two coats of oil emulsion distemper over a coat of wall care putty of 1 mm thick on new plaster surface complete all as specified and as directed.

Applying three coats of white/ colour washing on new plaster surfaces including preparation, necessary scaffolding complete all as specified and as directed.

Applying two coats of oil emulsion distemper over a coat of 1mm thick wall care putty on old decorated surface including complete removal of existing treatment complete all as specified and as directed.

Applying two coats of white/ colour washing on old decorated surfaces including preparation complete all as specified and as directed.

Two coats of synthetic enamel paint on new steel surface over one coat of red oxide primer complete all as specified and as directed.

Preparation of two coats of synthetic enamel paint on new wooden surface over one coat of pink primer complete all as specified and as directed.

One coat of synthetic enamel paint on old steel surface over one coat of red oxide primer complete all as specified and as directed.

Preparation of one coat of synthetic enamel paint on old wooden surface over one coat of pink primer complete all as specified and as directed.

Glass fibre reinforced modified cementitious coating system before the final coat of Latex Shield 2K (or equivalent) in Sunken treatment. Base coat : Berger HS Latex plus (or equivalent), Consumption base coat : 0.3 Kg/Sqm, Reinforcement : Glass fiber, Second and Third coat : Latex sheild 2K (or equivalent), Consumption top coat: 3 Kg/Sqm, System requirements : density: 2.00 Kg/Ltr, Compressive strength : 0.5 N/Sqmm. (i) Wall penetration through the RCC slab must be sealed using Berger HS Repir (or equivalent). (ii) Intersection of base slab with wall must be provided with a 50 mm fillet using Berger HS Latex plus (or equivalent) modified mortar with a bonding coat of Berger HS Latexplus (or equivalent) modified cement slurry upto 1.5 Mtr. (iii) All depressions, unevenness, surface honeycombing shall be repaired using Berger HS Latex plus (or equivalent) modified polymer mortar with a bonding coat of Berger HS latex plus (or equivalent) modified cement slurry, including removing of existing sunken, cleaning of RCC surface to remove dust, loose particles, etc with compressed air or any other suitable technique depending on site conditions, grinding any sharp edges, etc complete all as specified and as directed.

Preparation of old steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint complete all as specified and as directed.

Preparing of new plastered surface of wall surface and applying exterior wall care putty and acrylic smooth exterior paint of required shade (Two coats over and including priming coat of exterior primer applied as per manufacturer's instructions) (including all necessary scaffolding, lifting arrangement up to 12 mtr height) complete all as specified and as directed.

Dismantling or Demolition of loose concrete and Material and labour for Gunniting to existing RCC Chajja, facia, parapet, beams, landings and similar RCC members after removing all loose concrete and preparations of surface, application of derusting chemical such as Dr Fixit Rust Remover or equivalent, priming reinforcement bars with a coat of zinc primer of coating not less than 40 micron, provision of bonding agent with bonding material like Dr. Fixit bonding agent and repair to external RCC structure with slurry light and steel/ ply form work and shortcrete concrete of mixed (1:3:1) (one part of cement, three parts of coarse sand and one part of 10mm and down aggregate) of minimum 50mm thick including plastering 10 mm thick in cement mortar (1:3) (all priming and bonding epoxy based paint shall be of Dr Fixit epoxy zinc primer or equivalent) etc complete all as specified and as directed. Note: - The rates include for necessary formwork, scaffolding and lifting arrangement up to 12 mtr height.

Pre-painted galvalume aluminium zinc coating 275gm/sqm GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws with suitable washer complete all as specified and as directed.

Pre-painted galvalume aluminium zinc coating 275gm/sqm GI based plain steel sheet for ridges 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws with suitable washer complete all as specified and as directed.

Pre-painted (factory painted) box type mild steel windows/ Ventilator (factory made) outer frame made out ERW tube 'P' section 65 X 45 X 25 mm and shutter of ERW tube 'P' section 50mm X 35mm X 20mm openable (double shutter) with glazed shutter on external side and gauzed shutter fixed with galvanized mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm including necessary GI wire staples etc on internal side including steel pintel hinges steel handle 100 mm long mild steel tower bolt 02 no's on each shutter stopper of 'Z' section and its locking arrangement and mild steel hook and eyes suitable for fixing cooler/ AC window complete all as specified and shown on drawings No CEPZTD-324/07 Sh 1/3 to 3/3 and all as directed. Note(i): - The quoted rates shall also include: - (a) Two coats of synthetic enamel paint over one shop coat of zinc chromate primer on all exposed surface complete and one coat of tar on the ends of steel surface in contact with bricks/ concrete surface. Colour/ shade will be approved by Engineer-in-Charge. (b) 4 nos MS steel lugs made of 20x5 mm Iron flat 200 mm long. (c) 10 mm Sq Bar grill/guard bar design as per drawing. (d) PCC block for embedding lugs complete. Note(ii)-: Galvanised mild steel wire cloth and sheet glass shall be measured and paid under respective items of BOQ.

30 mm thick flush shutter, solid core construction, with block board core and plywood face panels commercial type on both side fitted to chowkhats complete all as specified and as directed.

35 mm thick second class hard wood glazed and skeleton shutters including door spring/ stopper, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc complete all as specified and as directed.

Solid PVC door frame of size 50mm x 47mm made out of 5 mm plain coloured PVC sheet, reinforced with mild steel square tube supplying and fixing in opening as per specification complete all as specified and as directed.

Factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles), with 2, 4 or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2 mm plain colour PVC sheet on back face, with particle board core, supplying and fixing in frame at site as per specifications and drawings shown in section 8 of SSR Part - II complete all as specified and as directed.

4mm thick of size 605 x 605 mm, white pre-premiered, self embossed, reinforced designer board for false ceiling conforming to IS-14862 and ISO-8336:1993 and GI section frame work (Powder coated) for white, pre-premiered, self embossed, reinforced designer board consisting of perimeter wall angle 19mm x 19mm x 0.45mm, cross 'Tee' 28.6mm (web) x 24mm flange. 33mm thick powdered coated main tee 38 (Web) x 24mm flange 0.33mm thick. Wall angle screwed fixed to brick wall / partition wall / concrete / RCC with the help of nylon sleeves and screws @ 610 mm centre to centre, then suspending GI main 'Tee' in both directions by means of hangers with alignment @ 1220mm centre to centre to soffits. To from grid of 610 x 610mm cross Tee shall be provided @ 610mm centre to centre in both directions. Suitable provisions shall be made for fixing the recessed/ surface mounting light fittings if any complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing of TEAK WOOD sports flooring as per specifications and conditions mentioned below: - Technical Specification: Hard TEAK WOOD Flooring 20mm thick each individual strip of Hard TEAK WOOD shall include the engraving of the minimum width of Hard TEAK WOOD boards is 57mm and of random length varying from 230mm to 1800mm jointed together with the help of tongue and groove on all four sides of all boards. Substructure: Substructure of TEAK WOOD flooring shall consist of sleeper of Spruce or Pine having 63mm wide and cross section of 38 mm and laid perpendicular to the main flooring planks at a spacing 305mm centre to centre including 9.5 mm thick rubber shock pads at 305mm centre to centre spacing and polyethylene membrane installed over the concrete base beneath the flooring system as a vapour barrier between the concrete and wood floor. Vapour Barrier: 0.20mm polyethylene membrane installed over the concrete base beneath the flooring system as a vapor barrier between the concrete and wood floor. Gym Finish: Machine sanding two coats of oil modified Polyurethane Gym sealer and one coat of oil modified Polyurethane Gym sports finish in accordance with manufacturer specification and Game line marking in accordance with manufacturer's specifications and project drawings etc complete all as specified and as directed.

Supply and fixing of Hard plaster for Squash court (Cement Plaster) made of 10-12mm thick cement-rich render containing Portland cement mixed with SBR Latex and Fiber wool. This plaster is applied with trowel. After plaster is cured and the Moisture level will be less than 8. Final coat approved Hard plaster is applied with Trowel to achieve grey color playing wall. The court is finished with Game Line Marking complete all as specified and as directed.

Supply and fixing of Court Glass Back wall. The glass installed as Glass back wall is fully tempered (12 mm thick clear toughened glass) thick safety glass manufactured by a horizontal process. The total size of the glass wall shall be 2.13 mtr height x 6.4 mtr Width. The Glass wall shall consist of 4 panel of size 2153 x 1436 mm each with the thickness of 12 mm, a glass door size 2128 x 678 thick of 12 mm. The Glass work is finished with locally produced lock and hardware. The Glass will be supported with Fins of size 350 mm x 2196mm 1 SET complete all as specified and as directed.

Supply and Installation of Sensor Tin Board in front wall, Adjustable height steel pressed powder coated sound board, Fabricated to fix and detach easily, Total height 480 mm complete all as specified and as directed.

Galvanized mild steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm fixed with tinned tacks or galvanized wire staples complete all as specified and as directed.

Supply and fixing in repair galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Sheet glass 3mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane including glazing pins or spring clips (including all necessary scaffolding, lifting arrangement up to 12 mtr height) complete all as specified and as directed.

Vitreous China squatting pan, Orrissa pattern with integral foot rest size, 580 mm x 440mm white including ‘P’ or ‘S’ trap front or back inlet and foot rests any pattern fixed in repair including concrete bedding complete all as specified and as directed.

Vitreous china wall hang corner wash hand basin, size 400 x 400 x 195mm including iron brackets/ fastener, 32mm bore PTMT waste coupling, waste pipe and PVC connection pipe of 15mm x 450mm long complete all as specified and as directed. Make: - Cera Cat Part No : S2040161 or equivalent in makes as specified in Group - I of Appx 'F'.

Butt hinges, medium weight, cold rolled mild steel and fixed (Size of hinges in 125 mm) complete all as specified and as directed.

300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed etc. complete all as specified and as directed.

200 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

150 mm mild steel pressed handles, oval type door handle, including welding/ rivetting etc complete all as specified and as directed.

Mild steel 300 mm, ordinary rat tail rod pattern springs (helical door spring) including roller and roller plate complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I including dismantling of existing water tank, including 20mm Ball valves, 20mm tank nipple complete all as specified and as directed by Engineer-in-Charge.

25mm outer dia CPVC gate valves complete all as specified and as directed by Engineer-in-Charge.

Supplying and laying of 25mm outer dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings on concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, Tee short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc.) complete all as specified and as directed.

15mm dia tubes medium grade galvanised, with all fitting and clips fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

20mm dia tubes medium grade galvanised, with all fitting and clips fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

20 mm chromium plated Stop valves, fancy type cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed (20mm bore dia of pipe) complete all as specified and as directed.

15mm bore dia Pillar taps fancy type cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

Brass chromium plated mixer (wash basin/ wall) 15 mm bore for mixing hot and cold water screwed down for iron pipe or any type of pipe and fixed in position and making good disturbed portion complete all as specified and as directed.

15 mm chromium plated bib taps fancy type cast copper alloy with crutch or butterfly handle screwed down, screwed for iron pipe or for brass ferrule and fixed (15mm bore dia of pipe) complete all as specified and as directed.

15 mm chromium plated Stop valves fancy type (angle valve) cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions and fixed (15mm bore dia of pipe) complete all as specified and as directed.

Low level flushing cistern of capacity 10 litre ISI marked complete with inlet ball valve, connection to pipes and handle including connecting pipe, bracket etc complete all as specified and as directed.

Chromium plated tubular towel rail, 20mm dia 'D' type, 60 cm long between flanges complete all as specified and as directed.

Sinks with drainage board made of stainless steel 1 mm thick kitchen with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

PVC connections 15 mm size with PTMT nuts of length 750 cm complete all as specified and as directed.

Grating doom 100/ 125 mm dia with waste hole/ without waste hole of PTMT/ chromium plated. (Minimum weight 40gms) complete all as specified and as directed.

Chromium plated shower rose 125mm dia with approx 450 mm long 15mm dia steel pipe with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed.

25mm dia curtain rods, chromium plated with fixing brackets, stops, side finnels etc complete with all fittings all as specified and as directed.

Chromium plated brass angle valve two way for 15 mm bore pipe, fixed in repairs complete all as specified and as directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm bore pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified and as directed.

Stainless Steel plate rack made out of 1mm thick sheet of size 750 x 600 x 250mm of size having partition and fixed with steel fasteners or steel screwed complete all as specified and as directed.

Butt hinges, medium weight, cold rolled mild steel and fixed (Size of hinges 100 mm) complete all as specified and as directed.

150 mm long Aluminium anodised barrel tower bolts of extruded section complete all as specified and as directed.

150mm long aluminium handles, cast type, anodized and fixed complete all as specified and as directed.

110 mm dia bore for rain water/ sewage PVC (SWR) pipes single socketed in any length with clips, solvent cement joints, fixed to wall complete all as specified and as directed.

PVC (SWR) bends of bore 110mm dia complete all as specified and as directed.

75mm dia PVC (SWR) pipes single socketed in any length with rubber joints fixed to walls/ floor etc complete all as specified and as directed.

PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement etc complete all as specified and as directed.

PVC (SWR) bends / Tee / Y 110mm dia any radius with access door complete all as specified and as directed.

PVC (SWR) floor trap 75mm dia plain including jointing with solvent cement etc complete all as specified and as directed.

Coloured Non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm, in floors etc. set and epoxy grouting including screed bed or bedding layer of mortar 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.

Coloured glazed ceramic tiles in vertical surface glazed ceramic tiles in vertical surface 350 x 250 x 7 mm/ 450 x 350 x 7mm thick set and epoxy grouting including 10mm thick screed bed or bedding layer of mortar in cement mortar (1:4) as in vertical surface etc complete all as specified and as directed.

18-20 mm thick granite (of any type/ colour) work (table rubbed and polished) in window cills, cooking platforms and like in cement mortar (1:4) including edge moulding, fixing in any position in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Machine cut and polished smooth surface of kota stone slab 18-20mm thick as in skirting/ steps, including 15 mm thick cement mortar and screed bed (1:4) fix in position etc complete all as specified and as directed.

Machine cut kota stone 20-25 mm thick as in floor, laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and mirror polishing over 20mm thick screed bed in cement mortar (1:4) as in floor complete all as specified and as directed.

E/M Portion: - Taking down old unserviceable copper/ aluminium point wiring concealed/ batten (light, fan, socket or power) complete including fixtures and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden/ PVC/ iron, round block etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Taking down carefully unserviceable distribution boards and TPN DBs of any type/ size with MCBs and disconnecting and making good disturbed surfaces complete all as specified and as directed.

Material and labour in replacement for sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length including taking down old wiring complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in replacement for complete point wiring with 1.5 Sqmm two single core multistranded copper conductor FRLS insulated and unsheathed heavy duty cable in colour coding including continuous earth wire with cable of size 1.5 Sqmm copper conductor flexible FRLS insulated drawn in and including concealed PVC rigid conduit medium grade ISI marked after cutting chases in wall, plastering after concealing conduit, including modular galvanised flush boxes of suitable size and white cover plate with frame as per relevant IS for mounting modular switches, sockets, fan regulators etc and including making good the disturbed surface as per existing complete all as specified and as directed by Engineer-in-Charge for the following: -

Description all as per Ser item No 123.00 here-in-before but for multi 5 pin 5 amp socket outlet on same board ISI marked complete all as specified and as directed.

Description all as per Ser item No 123.00 here-in-before but for multi 5 pin socket outlet 5 amp socket on independent board ISI marked complete all as specified and as directed.

Description all as per Ser item No 123.00 here-in-before but for One bell/ buzzer point controlled by one push button on the same board with other switches or independent with cable 1.5 Sqmm size complete all as specified and as directed.

Description all as per Ser item No 123.00 here-in-before but for multi 6 pin 15 Amp socket outlet independent controlled by 15 Amp switch with 2.5 Sqmm copper conductor multistranded cable PVC insulated FRLS and unsheathed cable in and including PVC rigid concealed conduit 20/25 mm dia and unsheathed copper conductor multistranded cable 2.5 Sqmm as earth wire FRLS PVC insulated in green color complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in replacement modular socket, 6A - 5 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 module 6A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular bell push 6 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement ceiling rose, 3 Pin/ PVC/ polycarbonate isolated body ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular switch 1 way 16A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement modular socket 6A/16A - 6 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing in replacement Calling bell Ding Dong/ buzzer AC 230 Volts, single pole ISI marked complete all as specified and as directed.

Material and labour in replacement for Lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour in replacement self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing in replacement LED lights fitting 1 x 18W, 220V, AC decorative box type complete with LED tube rod 18 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in replacement of Vertical Distribution Board (V.TP&N) 4 way double door suitable for TPN 4 pole 125 Amp 16 KA four pole as incomer, it should be IP-43 protected with copper bus bars, neutral links, Earthing bar complete all as specified and as directed.

Material and labour for replacement distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same Make

Supply and fixing in replacement SPN 40 to 63 Amp rating 240V, 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 6 to 32 Amp complete with connection, testing and commissioning complete all as specified and as directed.

Earthing complete with galvanised mild steel earth plate electrode of size 600 x 600 x 6mm thick burried directly in ground earth (in vertical) earth pit not less than 2.25 mtr deep below normal ground level with top edge of the earth plate not less than 1.5 mtr below ground level connected to galvanised iron or earth lead wire 4mm dia (8 SWG) by means of nut, bolt, check nuts and washer of galvanised iron including PCC pit in PCC (1:2:4) type B-1 precast RCC cover slab using reinforcement with suitable handle made of round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanised steel tube for watering with one end fixed with cast iron funnel and wire mesh 15mm dia bore light grade galvanised steel tubing upto 5 m length for drawing earth lead wire protection, common salt, charcoal, etc complete all as shown in electrical plate No 3 of SSR Part-I and testing on completion complete all as specified and as directed.

Supply and fixing in replacement LED light fitting 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP- 65/66 protection complete all as specified and as directed.

Supply and fixing in replacement 415V 10 KA 'B' curve miniature circuit breaker (MCB) TPN 4 Pole, upto 125 Amps of following poles and current carrying capacity in the distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement fan step regulator, 100W - 1 module 240 volts ISI marked complete all as specified and as directed.

Disconnecting and taking out defective service/ underground cable any size and any type from trenches, roof, pole, pipe, floor, wall etc complete all as specified and as directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 4.0 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc. complete all as specified and as directed. Note: - (i) Earth work, sand, bricks, removing, returning filling Aluminium thimbles/ lugs will be paid separately. (ii) Cost of laying electrical cable through new/existing pipe under road, buildings, railway tracks, highways are included in the quoted rates. (iii) All equipments, machinery or tools if required for laying electrical cable through new/existing pipes are provided by the contractor without any extra cost.

Supply and fixing in repair LED luminaire 600 mm x 600mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamp suitable for roof, ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed.

Supply and laying, connecting and testing XLPE underground cable insulated and overall sheathed with aluminium conductor heavy duty 1100 volts grade 16 Sqmm 2.0 core laid in trenches/ on poles/ road crossing or passing through existing/ new pipe under road crossing, clamping on wall etc complete all as specified and as directed.

Power unit for AC with MCB 25 Amps including protected socket 25 Amps, white modular gang box and plate 4 way complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing LED lights fitting 1 x 20W, 220V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.9, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in replacement MCB SPN 40 to 63 Amp rating 240V, 10 KA 'B' curve type, in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Dismantling and taking down old unserviceable flood lights and material and labour for new LED flood light fittings of 150 watt, system wattage and high pressure die cast aluminium housing with sealed toughened glass cover, silicon gasket for IP-66 protection suitable for pole mounting SMD LED array with lense, cool white 6500 K, system efficacy 90 lm/W, 240 Volts AC, 50 Hz, CRI >70% operating voltage range 160 V - 270 V, Power factor >0.95, working temperature range - 20º C to 60º C, built in surge protection more than 10 KV with facility including make proper connection complete including cutting, welding, drilling holes, nut bolts, washer complete all as specified and as directed by Engineer-in-Charge.