SPECIAL REPAIR TO BLDG NO T-13 OF 506 ABW UNDER AGE B/R-II OF GE (EAST) JABALPUR

Amount

Excavation in treanches n.exc 1.5m wide and n.exc 1.5m in depth for foundation, etc or for shafts, wells exc 10 sqm on plan and getting out any type of soil complete all as specified and directed.

Sand filling under floors or in foundation including watering & consolidation complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm complete all as specified and directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point complete all as specified and directed.

M&L Hardcore of gauge n.exc 63mm, broken stone deposited, spread and levelled in layers n.exc 15cm thick, watered and rammed to a true surface complete all as specified and directed.

Treating the soil under plinth protection at the rate of 5 litres of emulsion per square metre of surface area complete all as specified and directed.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors complete all as specified and directed.

PCC (1:3:6) type C-2 using 40mm graded crushed stone aggregate as in filling, foundation & mass concrete complete all as specified and directed.

PCC (1:4:8) type D-2 using 40mm graded crushed stone aggregate as in foundation & mass concrete complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in copings, benching, bed block, lintel band, plinth courses, kerbs etc and similar work including necessary form work complete all as specified and directed.

M&L for precast cement concrete 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in landings, cover slab (for drain etc) and similar work including necessary form work and set in CM 1:6 complete all as specified and directed. Note : (a) Curing tank should be constructed 4 x 4 x 9m at site. (b) Steel from work must be used for casting. (c) PCC plateform must be constructed at site. (d) It shall be paid separately and TMT Bar will be paid seperately.

RCC design mix M-25 using 20mm graded crushed stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

RCC design mix M-25 using 20mm graded stone aggregate in Columns, pillars, butters wall, piers, posts and struts complete all as specified and directed.

Supplying only intergral Water Proofing Compound (ISI Mark).

Brick work with sub class `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

Use and waste of form work to rough finish surfaces of concrete sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc, edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc sash bar any numbers complete all as specified and directed.

Taking down Chowkats or frames n.exc 1.5 sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

Taking down & Removing to Store Chowkats or frames exc 1.5sqm but n.exc 4sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottomrails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stile sand plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, Panelling of plain colour PVC sheet to befitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC Sheet & edges will be painted to match with prelam sheet, reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

Factory made single extruded WPC (Wood Polymer Composite) solid door frame of size 125 x 65mm comprising of virgin PVC polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC slovent cement and screwed with full body threaded star headed SS screws havng minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N (face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticty 900 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S hold fast/lugs or SS dash fasteners shall be paid for seperately. Note : For WPC solid door minus 5mm tolerance in dimension i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable nut no extra payment on this account shall be made.

Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (suspension grade), calcium carbonate and natural fibre (wood powder/rice husk/wheat husk) and non tixic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 Kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (Edge), minimum compressive strength of 50 N/mm2, modules of elasticty 850 N/mm2 and resistance to spread of flame of Casss A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessay full body threaded star headed counter sunk S.S screws, complete all as specified and directed.. Note : stainless steel butt hinges and necessary S.S screws shall be paid separately.

S&F Aluminium anodised, barrel tower blots 150mm long, stove enamelled black, with bright bolt complete all as specified and directed.

S&F Aluminium anodised, barrel tower blots 200mm long, stove enamelled black, with bright bolt complete all as specified and directed.

S&F aluminium alloy sliding door bolts 300mm long, plate type, stove enamelled black, with bright bolt not less than 12mm dia with & including a minimum of 6 bolts & nuts, four on bolt plate & two on staple plate complete all as specified and directed.

S&F 100mm butt hinges extruded aluminium alloy with galvanised MS hinge pin anodised and fixed type C-21 complete all as specified and directed.

S&F 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and directed.

S&F Aluminium handles 100mm size, cast type, anodised complete all as specified and directed.

S&F Aluminium handles 150mm size, cast type, anodised complete all as specified and directed.

S&F 40mm dia, brass cupboard knobs fixed with nut, screw and washer of mild steel bright complete all as specified and directed.

S&F Mortice lock, vertical type size 100 mm 4 lever complete all as specified and directed.

S&F MS hand rails, half round or other section for wind ties for roof including securing bolts, drilling holes, notching complete all as specified and directed.

S&F mild steel screw bolt (machine made) with square or hexagonal head at one end, screwed other, fitted with washer and one hexagonal or square n.exc 5cm long and 10mm dia complete all as specified and directed.

S&F mild steel screw bolt (machine made) with square or hexagonal head at one end, screwed other, fitted with washer and one hexagonal or square exc 10cm but n.exc 15cm long and 10mm dia complete all as specified and directed.

S&F Curtain dropary 25mm dia and 1.5 mm thick mild steel rod of fancy type with PVC coating excluding brass and brackets with curtain rings of approved quality etc complete all as specified and directed.

S&F mild steel Nobs and bracket complete all as specified and directed.

TMT HYSD reinforcement bars 10mm over dia including all cutting bending, binding, cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed.

TMT HYSD reinforcement bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

S&F Rolled mild steel Roof trusses (framed), trussed purlins crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle channel or flat sections) including distance pieces, cleats etc conforming to Fe-410-W (Gde E-250) quality-A, complete all as specified and directed. Note :- (i) The rate quoted allow for cutting to dead length where required, notching, drilling fitting, reveting and /or welding or connecting with bolt and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plate gusset plates etc also for welding, plumbing, truing up and fixing complete. (ii) Truss design shall be got done by the contractor duly vetted by Govt Engineering College/NIT and expense thereon shall be deemed included in quoted rates.

S&F Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip & straight flashings (length & girth as fixed) with grade of zinc coating 275 of 1.00mm thick complete all as specified and directed.

S&F pre painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding and in ridge to wall, fixed with self tapping screws complete all as specified and directed.

M&L Machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 20mm screed bed in CM (1:6) complete all as specified and directed.

M&L 75mm thick PCC type C-2, (1:3:6) using 40mm graded crushed stone aggregate as in plinth protection finished even and fair & smooth without using extra cement complete all as specified and directed.

S&F Coloured Glazed ceramic tiles in vertical surfaces 350 x 250mm x 7mm/450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm thick plaster in CM (1:4) on fair face of brick or concrete surface complete all as specified and directed.

S&F Coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exc 0.11sqm but n.exc 0.18sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM (1:6) complete all as specified and directed.

M&L Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with ditto as per above including to match over 10mm thick screed in CM(1:4) complete all as specified and directed.

M&L for machine pressed precast cement concrete rubber moulded inter locking paver block any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade complete all as specified and directed.

Dismantling, floor, hearth or wall tiling including CM (bedding (but not backing), removing serviceable tiles to store & rubbish off the premises complete all as specified and directed.

M&L for near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

M&L 15mm thick plaster in CM 1:4 in two coats of 10mm first coat (including dubbing coat finished even & smooth without using extra cement and 5mm final coat. Both coat milled with WPC complete all as specified and directed.

M&L Rendering 15mm thick on brick work or concrete surfaces of wall in CM (1:6) finished even & smooth (without using extra lime or cement) complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed.

Taking down existing loose plaster & Clean rusted reinforcement and exposed concrete surface by sandblasting mechanical devices or any other estabilished methods and follwing stagecomplete all as specified and directed :- (a) Application of two coats of mineral based polymer modified corrosion inhibiting primer Colusal MK +Colusal 25. (b) Application of two component polymer based bond coat Zentrifix HB+Natufill BB2 or mortar low permeability or guinting with guniting aid. (c) Application Application of carbonation resistant, polymer modified reeady to ise fine mortar ,Nafuquick +natufill BB2 or Zen-trifix F82+Nafufill BB2 Over the whole surface.

Preparation of new decorated surfaces of walls and applying two coat of oil bond distamper over a coat of primer over 3mm thick wall care putty complete all as specified and directed. (Wall care putty make Birla White, JK) complete all as specified and directed.

M&L complete removal of existing surface of wall and applying two coat of oil bond distamper including primer over 3mm thick wall care putty complete all as specified and directed. (Wall care putty make Birla White, JK) complete all as specified and directed.

Applying two coats of cement base paint, white or tinted on new wall including primer surface including preparation of surface complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of cement base paint, including primer on wall surface including preparation of surface complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based surfaces of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old painted surfaces of steel of any description, over 10cm in width or girth and apply one coat of synthetic enamel paint complete all as specified and directed.

Applying two coats of synthetic enamel paint on steel & iron surfaces of any description, not otherwise, described, over 10cm width or girth including preparation of new surface & applying one coat of red oxide, zinc chrome complete all as specified and directed.

S&F precoated steel window Rolled formed GI Section ECO 4000 (Openable double rebate window) providing and fixing of single rebate openable/fixed windows made of galvanised steel colour coated/powder coated (base steel as per IS 513 of “D" quality, galvanised as per IS 277 with zinc of 120 grams/sqm) with total thickness of coating 0.58 microns, primer coated with epoxy primer of 5-7 microns thick, finish painted with a polyester paint of 12-16 microns thick and back coated with alkyd backer 5-7 microns thick or powder coated with pure polyester powder up to 50-60 microns thick, outer frame section 48 x 50mm, centre mullion section 48 x 50mm, shutter section 47 x 20mm and the fixed glass beading section 12 x 12mm, outer frame and mullions shall consists rebate for glazed shutter with a 20mm provision for guard bars/grills and the sections cut to length mitre joined with corner bracket, centre mullion fixed with mullion cap, handle, stay, 2 Nos. SS( stainless steel) heavy duty pivot hinges per shutter and window fitted with 5mm thick plain float glass with EPDM (Ethyl Propylene Diamine Monomer) gaskets including fixing frames in concrete/masonry wall by means of self expanding screws, Including 10mm Square bars welded to 6 x 12mm flat at a distance 150mm c/c (pitch) etc complete all as specified and directed.

Supply & Fixing 'in repair' 18mm thick, PVC sheet one side 1mm pre-femlaminated of approved texture ("Celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE ) as in Kitchen cabinet (withshelves and partitions) inas per manuacturer's instructions complete all as specified and directed.

Supply & Fixing 'in repair' 18mm thick, PVC sheet one side pre-laminated of approved texture ("Celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE ) as in cupboard (withshelves and partitions) as per manuacturer's instructions complete all as specified and directed.

S&F for 50mm dia GI Pipe light grade for cable protection passing under road/floor or for fixing to poles all as complete all as specified and directed.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 15mm bore complete all as specified and directed.

S&F GI Tubes, `medium grade' with all fitting & fixed complete to walls & ceilings or laid in floors of 20mm bore complete all as specified and directed.

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store complete all as specified and directed.

Dismantling water tanks capacity exc 500 Ltr but n.exc 1000 Ltr and removing from site complete all as specified and directed.

S&F rotational molded polyethylene water storage tanks white tripple layer (cylindrical vertical with closed top) capacity 1000 Ltr hoisted and fixed in position complete all as specified and directed.

S&F in repair bib tap fancy type chromium plated screwed for iron pipe of 15mm bore complete all as specified and directed.

S&F 15 mm dia CP concealed angle cock for rose shower complete all as specified and directed.

S&F 20mm dia gate valves/Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F fancy type, chromium plated with long shank and cup Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (concealed type) complete all as specified and directed.

S&F 20mm dia Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed.

Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

S&F PVC (SWR), junction single, (Single T) equal or unequal 110mm dia complete all as specified and directed.

S&F PVC (SWR) vent cowl 110mm dia complete all as specified and directed.

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

M&L cement concrete 1:4:8 type D-2, 300mm bore for concrete bed to drain pipes including packing under and haunching against the side of pipes complete all as specified and directed.

S&F reinforced concrete pipes, 300mm bore class NP2 laid jointed complete with collars complete all as specified and directed.

S&F in repairs Brass CP shower rose 125mm size complete all as specified and directed.

M&L Forming 12mm thick Expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade ‘A’, complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stone work & precast concrete articles complete all as specified and directed.

Demolition of cement concrete (Unreinfored) in gound floor and paving n.exc 15cm thickness (below or above gound level) complete all as specified and directed.

Demolition of reinforcement cement concrete landing cover slab demolition complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified and directed.

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering complete all as specified and directed.

Dismantling of AC corrugated/semi corrugated sheets as in roof covering complete all as specified and directed.

Demolition Wall & ceiling boards (fibre, pulp, insulation, etc) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition & breaking up drain pipes (salt glazed ware, AC or reinforced concrete) set in CM internal dia of pipe 300mm complete all as specified and directed.

M&L suspended false ceiling system using Chicago metallic (E-grid) exposed suspended system, grid size 600 x 600mm compressing of GI powder coated main runner of dimension 39mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm+PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length), cross Tee of dimension 29mm x 24mm x 0.8mm thick (Thickness comprising of GI/0.4mm+PPPCGS/0.3mm & weight of Tee 0.195Kg for 600mm length) and wall angle of dimension 22.2mm x 22.2mm x 0.65mm thick (Thickness comprising of GI/0.35mm + PPPCGS/0.30mm & weight of angle 0.700 Kg for 3050mm length) with and including 6mm thick HPSC (High Pressure Steam Cured) pre-primed, self embossed, textured designer board, water, termite & fire resistant for insulation and acoustic purpose to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt 0.007 Kg/clip), hold down clips (weight - 0.0035 Kg/clip), with provn of light fixture complete all as per manufacturer instructions andcomplete all as specified and directed.

Supply, laying & testing and commissioning LT underground cable 1100 volts grade, XLPE insulated and PVC sheathed heavy duty armoured with multi staranded aluminium conductor laid in pipes, trences/ducts, on poles etc of size 50Sqmm 3.5 core and taking down old existing un-erviceable LT UG/ service cable of any size complete all as specified and directed.

S&F for Energy saving new generation environmental friendly long life versatile pressure source and electronic driver of IP 65, LED street light of capacity 35 watts with pre-wired and necessary mounting arrangements and provision of 2.5 sqmm three core copper conductor cable multistranded from ceiling rose to light fittig including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nuts, bolts etc complete all as specified and directed.

Taking down carefully copper/aluminium point wiring (light, fan, power point or bell point etc) complete including fixture and fitting such as switches, ceiling rose holders & regulators light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site.

M&L for point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5Sqmm (nominal area), two single core, PVC insulated and unsheathed FRLS cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty PVC concealed conduit of white/ivory colour including all accessories after chasing in wall/ceilling etc, heavy duty ISI marked with GI sunken boxes 1.2mm thick, 60mm deep with earth dolly, covered with modular white cover plate with inner frame suitable for modular swithes, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

One light point controlled by one, one way switch 5 Amps.

One fan point/exhaust fan point controlled by one, one way switch 5 Amps and regulator.

One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on the same board.

One 3 pin 5 Amps switch socket outlet point controlled by one, one way switch on indelpendednt board.

All as per item Srl No 101 here-in-before but using 2.5 Sqmm single core copper conductor cable of multistranded FRLS, PVC insulated unsheathed 1100 volts grade for 5/15 amps witch socket combination point including necessary running of 2.5 Sqmm copper conductor FRLS, PVC wire as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed.

All as per item Srl No 101 here-in-before but using 4 Sqmm single core copper conductor cable of multistranded FRLS, PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including necessary running of 4 Sqmm copper conductor FRLS, PVC witre as earth continuity conductor alongwith wiring an connecting to the common earth dully, complete all as specified and directed.

Use and waste of form work to rough finish surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M&L for Fly Ash bricks Sub-class 'B' locally available laid flat in trenches over sand cushioning for cable protection complete all as speciffied and directed.

Taking down old/unservicable light fitting any type and S&F new 1 x 10 W LED light fittings wall mounted LED batten, extruded aluminium heat sink provided for efficient heat dissipation and integrated electric driver including 1 x 10W LED ube light etc complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size compete all as specified and directed.

S&F for energy saving new generation 10 watts LED bulk head fitting IP-65 luminaire with opel diffuser pre-wired with warranty option of 5 years from date of installation and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specefied and directed.

S&F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen output box type fitting, 230 volts and intregrated electronic driver connector block etc with necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specefied and directed.

S&F Lamp holder, PVC/polycarbonate type with back plate suitable for battan fittings, complete all as specified and directed.

S&F for modular Switch piano flush type, single pole, one way and 5/6 Amp, single modular complete all as specified and directed.

S&F for modular Switch piano flush type, single pole, one way and 15/16 Amp, single modular complete all as specified and directed.

S&F modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amps and 2 pin, 5/6 Amp, 2 module piano flush type complete complete all as specified and directed.

S&F modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amps and 3 pin, 5/6 Amp, 2 module piano flush type complete complete all as specified and directed.

S&F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and directed.

Taking down old/unservicable MCCB any type and Supplying and fixing MCCB 4 Pole, 415 V, Adjustable type, 100 Amps with breaking capacity 16 KA complete all as specified and directed.

S&F sheet metal enclosures with socket, plug, top complete clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and directed.

S&F for sheet metal enclosure MCB DB SPN 8 Way vertical type with 200 Amps rated bus bar 240 volts double door with magnetic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and directed.

S&F ceiling rose surface type PVC/Polycarbonate isolated body, 65 x 20mm, 3 terminals, complete all as specified and directed.

Hanging only ceiling fan (MD supply) and connecting up including provision of cable from ceiling rose or connector to fan etc complete all as specified and directed.

M&L for main wiring with approved colour as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size 6 Sqmm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc, one run of PVC insulated with 6 Sqmm (nominal area) stranded copper conductor FRLS cable as earth wire complete all as specified and directed. Note : Two runs (with Red/Yellow/Blue colour for Phase + Black colour for Nutral) of 6 Sqmm cable, one run (with Green colour for Earth) of 6 Sqmm cable and one run of PVC conduit will be measured as one unit.

Taking down old/unservicable MCCB DB any type and M&L distribution board made out of CRCA sheet, powder coated, vertical type, double door, 4 way, including fixing in the wall after chase cutting and making good the surface by necessary patch work and surface finish as per existing including making connections complete all as specified and directed. Make : Havells cat part No DHDLVDRWACF004

S&F MCB single Pole rated capacity 5 to 32 Amps, 240 Volts, breaking capcity 10 KA "C" curve complete all as specified and directed.

S&F MCB single Pole and neutral rated capacity 40 Amps, 240 Volts, breaking capcity 10 KA "C" curve complete all as specified and directed.

S&F ceiling fan, 230 volts, 1200 mm sweep with service value of the fan shall be greated than 6.1 as per BIS with necessary aceessories and electrical connections for ceiling rose to fan terminal complete all as specified and directed.

S&F for energy efficient exhaust fan of 300 mm sweep made of metal body ventil Air-DS type complete with louver with bolts nuts and washers size lt 15 cm 12 mm dia embedded in the wall including provision of PVC flexible coppler cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connecttion and making suitable size of hole to existing brick wall for fan base complete all as specified and directed.

M&L for dismantling the ceiling fan/exhaust fan obtained from item No 101.02 with complete fittings at site removing fans are deposited to E/M store for keeping in safe custody for reuse at site all as specified and directed.

S&F for highly efficient LED bulbs, 10 watt used as a ready replacement for existing GL/CFL/direct fit lamp, in B-22 capacity complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground vertically (earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.50 mtr deep below normal ground level connecting to and including GI earth wire of size 4.0 mm by means of bolts, nuts, check nuts, and washers of galvanised iron or steel including 15mm dia medium grade pipe for protection of GI wire to the extent of 7.5 mtrs as earthing lead including charcoal dust and salt packed all around the earth plate in the earth pit all as per Electrical Plate No 3 of SSR Part-I (2009) including PCC foundation/chamber in mix 1:2:4 type B-1 with angle iron frame, CI frame, CI cover with provision of locking arrangement and 20 mm dia light grade GI pipe from top edge of the earth plate upto MS funnel with wire mesh provided inside the concrete earth pit for watering arrangement complete including excavation and earthwork in any type of strata and testing complete including fill up the earth pit with soil for best result and removal, complete all as specified and directed. Note - Earth protection pipe & earthing wire upto and including 7.5 m length shall be deemed included in unit rate quoted by the contractor.

Material and labour for boring hole under the road/path/pavment/hard standing with the help of trenchless technology using ultra sound technique and necessary machine including HDPE pipe of 50mm dia suitable for 0.4 mpa working pressure not less than one metre below ground level complete all as specified and directed at site. Note - The cost of HDPE pipe shall be deemed to be included in quoted rate by the contractor.

Schedule of credit amount of Rs. 1,15,939.00 to be deducted during AOC.

N.P.BUILDERS

LAL SINGH & SONS

MAYANK CONSTRUCTIONS