Jamtara Block Full Coverage Rural Water Supply Scheme ,Under DW and S Division Jamtara on turnkey basis.

Amount

Intake Well With Pump House

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand construction of R.C.C Intake well 12 M Dia and 24.22 M Depth Excluding 6 M Height of Pump house all complete job. (Please refer to Section 5,Sl. 2.1 of SBD)

Earthwork in excavation of foundation trenches of toe wall spillway head regulator, outlet intake well etc. as per designed section in all kinds of soil, including moorum soil, soil mixed with kankar, pebbles and boulders up to 300 mm size and disposal of the same (beyond 50 M away from the edge of the tranches) with in initial lead of 150 M and intial lift of 1.5 M as per specification and direction of E/I.

Initial Lift

Extra for earth work in all kind of soil for each additional lift of 1.0M or part there of over the initial lift of 1.5M as per specification and direction of E/I .

1st lift

2nd lift

3rd lift

4th lift

Earthwork in excavation of foundation trenches of toe wall ,spillway ,head regular or intake well and outlet etc. as per designed section in ordinary rock or soft rock (Vide classification of soil item-c) with disposal soil (beyond 50 M from the edge of the trenches) with initial lead of 150 m.and lift of 1.5 M as per specification and direction of E/I (soft rock where blasting is required and approved by the concerned Chief Engineer)

5th Lift

6th Lift

Earthwork in excavation of foundation trenches of toe wall ,spillway ,head regular or intake well and outlet etc. as per designed section in hard rockwhere blasting is needed and stacking properly in approved stack size in approved stack yard (beyond 50 m from the edge of the trenches in the country side ) with initial lead of 150 m.and lift of 1.5 M as per specification and direction of E/I (Excavated hard rock size should not be more than lb)

6th Lift

Plain cement concrete in well. Foundation complete as per drawing & technical specification. Well staining PCC M-15 Grade. (as per RCD 12.8 A)

Plain cement concrete in Well Foundatin complete as per drawing and technical specifications. Well staining PCC M15 Grade

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Plain/Rainforced cement concrete in Well Foundatin complete as per drawing and technical specifications. Well staining RCC M30 Grade. Case I Using concrete mixer.

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M25 . Using Concrete Mixer , For T-beam & slab, 25-35% of (a+b+c) Height above 10m M-250

Providing average 63 mm thick R.C.C.M- 200 with nominal mix of (1:1.5:3) in chajja with approved quality of stone chips 20 mm. to 6 mm. size graded and clean coarse sand of F.M. 2.5 to 3 including making drip course in concrete, screening, centering , shuttering, and mixing cement concrete in mixer and placing in position, vibrating, striking, 6 mm . cement plaster (1:4) in ceiling and sides of chajja with sand of F.M. 1.5, curing (but excluding the cost of reinforcement), taxes, and royalty all complete as per building and direction of E/I. specification

Providing Tor steel reinforcement of 10mm, 12mm and 16mm dia bare as per approved design and drawing excluding carriage of MS bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete job as per specification a n d directionof E/I.

Providing designation 75 A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, costs of screening , materials, scaffolding, raking out joints to 15 mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Supplying, fitting and fixing fully glazed steel door, windows or ventilations of standard rolled Z and mullion steel sections and size as per IS-1038 joints met and welded with 100 x 16 x 3 mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15 x 10 x 10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with Aluminium beads and inner frame fixed with lugs with 20 mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in position in all storys and taxes all complete as per building specification and direction of E/I.

Supplying and fixing rolling of approved size and make made of required size m.s laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to I.S 4454 Part I and M.S top cover of required thickness for rolling shutters

Ball Bearing for Rolling shutter .

Providing 12 mm. Thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12 mm thick water proof cement plaster (1:3) with clean coarse sand of FM 1.5 with 5 % cico or any other water proofing compound including screening curing, with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm. Thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface including preparing the plasterded surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Providing two coats of painting with ready mixed paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direction of E/I.

Providing R.S. Joist 450x150 mm size fitting and fixing in position including cutting to required in shape and size, its carriage applying a primer coat of red lead paint etc all complete as per building specification and direction of E/I. (Below roof slab for base of V.T.pump) (As per 3(c)

Supplying laying fitting and fixing 25mm dia G.I pipes of medium class railing well lengths of approved make is three rows each passing through 50x50x6 mm thick M.S angle at 1.5mm C/C and additonal post of every snowcem add painting 3 coats full paint over. One coat of aaticornssive paintg of approved colcurs add shade including cost of all labour, transporting, beats to curve shape etc. all complete job.

Prov. & fixing M.S Sluice gate in position do-do (as per MJP 15-16 item 12, page 224)

Prov. & fixing M.S rose piece in intake well do-do (as per MJP 15-16 item 13, page 224)

Providing and fixing in position C.I type dapuri steps of 22 mm dia M.S bar steps with proper anchorage etc and providing and applying 3 coats of corrosive paints etc complete as directed by E/I

Carriage of material from divisional store are kiln side or quality side to work including contractor profit loading, unloading transportation are complete .

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 6 KM lead

Stone/Stone Chips 11 KM lead

Gangway 580 M long and 5.0 M wide

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of RCC Gangay . etc. all complete job.(Please refer to Section 5,Sl. 2.2 of SBD)

Earthwork in excavation of foundation trenches of toe wall spillway head regulator, outlet intake well etc. as per designed section in all kinds of soil, including moorum soil, soil mixed with kankar, pebbles and boulders up to 300 mm size and disposal of the same (beyond 50 M away from the edge of the tranches) with in initial lead of 150 M and intial lift of 1.5 M as per specification and direction of E/I.

Initial Lift

1st lift

2nd lift

3rd lift

4th lift

Plain/Reinforced cement concrete in open foundation complete as per drawing and technical specifications. PCC Grade M15

Plain/Reinforced cement concrete, in well foundation complete as per drawing and technical specification. Well steining RCC M30 Grade. Case I- Using concrete mixer

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification RCC Grade M 30 Using Concrete Mixer Height 5m

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M 25 .Case I - Using Concrete Mixer , For solid slab super-structure, 20-30% of (a+b+c) Height above 10m Bracing = 2.40 x 0.25 x 0.35 x 5 no.= 1.05

Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification. RCC Grade M 25 .Case I - Using Concrete Mixer , For solid slab super-structure, 20-30% of (a+b+c) Height above 10m

Providing Tor steel reinforcement of 10mm, 12mm and 16mm dia bare as per approved design and drawing excluding carriage of MS bars to work site, cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete job as per specification a n d directionof E/I.

Providing 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification & direction Of E/I.

Providing 6 mm. Thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification & direction Of E/I.

Providing &Fixing G.I Pipe Railling having 1.0 m height consisting 50 x 50 x 6 mm thick M.S Angles as verticals at 1.5M c/c , and additional posts at every corner with 3 rows of 25 mm dia G.I. pipes of medium class variety as horizontal & painting 3 coats of oil paint over 1 coat of anticorrosive paint of approved colour & shade including cost of all labour, transporting bends to curved shape, etc. complete.

Providing two coat of snowcem of approved shade and make over a coat of cement primer on new surface including preparing plastered surface the smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Carriage of materials from divisional store or kiln site or quarry site to work site including contract prof it loadi ng , unloading , transportation, etc. all complete.

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone Chips 11 KM lead

Coffer Dam & Dewatering

Providing, constructing coffer dam in river basin / dam storages as per type design including excavation, filling the middle portion with B.C. soil (in gunny bags if required). Providing impervious / semimpervious materials on both side of B.C. soil (in gunny bags if required) including ramming , compacting to satifaction of Engineer-in-charge, till the completion of work including dismantling coffer dam after completion of works and disposing off material as directed by the Engineer-in-charge. Note-

Provision made for this item as per time of schedule given in department office order 197 dated 05.09.2013 of dwsd memo no.3825 dt.05.09.2013 and time schedule given in contract data of SBD during january to mid june month and approved given by field officer EE, SE and other. coffer dam design and drawing will have to be approved as per prevailing condition by competent authority.

For Intake Well

For Gangway

Dewatering the excavated trenches and pools of water in the building trenches/pipeline trenches, well works by using pumps and other devices including disposing off water to safe distanceas directed by Engineer - in-charge( including cost of machinery, labour, fuel) etc. complete

For Intake Well

For Gangway

(Mechanical & Electrical at Intake)

Doing survey, Collecting field data, designing, getting it approved by competent authority and Raw water pumping Machinery discharge of 5400 LPM against a total head of 42 M (2W +2S) with all complete job (Please refer to Section 5,Sl. 2.4 of SBD for detailed specification )

Raw water Pumpsets : Supplying, installing & commissioning of water lubricated, single/ multi stage, Radial/ Mixed flow, Vertical Turbine Pump having discharge 5400 Lpm against the total head 42 m of Kirloskar/ WPIL/ Mather & Platt make confirming to IS: 1710/1972, consisting of bowl assembly dynamically balanced bronze impellers, stainless steel pumpshaft and line shaft of 6m flanged column assembllies of 1.5m length and with 9mm thick MS fabricated column assembly, with strainers, prelubrication tank, Non reverse ratchet coupling, pressure gauge, Suitable size of NR valves, Sluice valves, Butterfly Valve & foot Valve with dismantling joint. Including Piping work for Delivery/ Suction line, common header, etc. coupled with TEFC & IE3 rated squirrel cage Induction Motor having 10% more BHP than that of pump, of Kirloskar/ ABB / BHEL/ CGL / Marathon make confirming to IS: 325 & IS: 12615, operating on 415 V, 3 Phase, 50 C/S, A.C Supply having speed 1500 rpm all complete as per standard specification and direction of E/I.

Discharge = 5400 Lpm, Head = 42 m (2W + 2S )

Starter : Supplying and erecting, assembled Fully Automatic Star Delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380- 440 Volt, 3 phase, 50 Hz with no volt coil, over load relay and ONOFF push buttons, with necessary material and connected to supply, etc complete.

Power Distribution Panel : Supply, Installation and Commissioning of Power control cum distribution cubical panel board (LT Panel), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder- 500 A TPN 415V MCCB with thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/ SIEMENS/ Schneider- 1no.

b) Outgoing feeder- 250A TP 415V MCCB having thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/SIEMENS/ Schneider- 4no. and 1no. Spare feeder.

c) Bus Bar- 4 pole 500A 415V copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

f) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Green colour- 1set.

g) 32A & 63A MCB and 100A MCCB for light load & other loads of L&T/SIEMENS/ Schneider make- 2nos each.

h) APFC panel of required & suitable KVAR with LT capacitor banks in standards stages with reactor coils for raising PF from 0.80 to 0.98,etc. all complete. Including motor control relays, earth fault relay, over/leakage current relay,etc. all other safety relays.

Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and including all type of relays with internally wired with suitable size of copper control wire/cable, etc. all complete.

Cables : Supplying , laying and suitably terminating both ends with following cables:-

(a) Cost of 400 Sq.M.M. x 3.5 core XLPE Aluminum armoured 1.1 KV grade cable including laying on cable tray along gangway from Transformer to LT Panel in the Intakewell pump house.

(b) Cost of 70 Sq.M.M. x 3.0 core XLPE 1.1 KV grade solid/ stranded armoured copper conductor with 6 mm thick cable including laying on wall/floor from LT Panel to Starter & Motors.

Lifting Equipment : Providing, erecting and commissioning of 3 Tonne single girder hand operated circular/ Rectangular Travelling Crane with 6 m lift complete with chain pully block ISI marked and traveling trolly both tested for 50% over load including arrangement for longitudinal travel /circular travel and cross travel with wheel , hand chain , etc. all complete.

Earthing : Providing & erecting earthing for each motors and Stabiliser with suitable Copper earth plate, GI pipe, charcoal, salt, etc. all complete as per IE Rule.

Lighting : Supplying and doing electrical wiring and internal and external lighting i.e. lighting of gangway and ESS for Raw water plant with LED luminaries as required and as per direction of E/I.

Additional Items : Supplying and erecting of Lightening Arrester for pump house,2 nos. Fire fighting system, emergency light with inverter and battery, display boards at pumphouse and ESS, safety gadgets e.g. hand gloves, gumboot, helmet, First aid box, insulation pad near each electrical controls and equipments, maintenance and measuring tools tools etc. as per requirement, standards and IE rule.

Electric Sub-Station ( ESS ) : Supplying, Installation & Commissioning of all materials e.g. different types of M.S channel M.S. angle, welded joint, nut bolts, Air break switch, 3 set horn gap fuses, Drop Out Fuse, LA, earthing complete set, Disc/ Pin insulator, fuse barrel, including the cost of fabrication, grouting & P.C.C. foundation block and providing safety arrangements, painting, PCC flooring, making cable ducts, covering by RCC slabs cover after laying required cables and sand filling and making and finishing plinth for installation of 1 Nos. 315 KVA (11KV/ 0.433KV) transformer with all required materials and acessories, etc. inside the ESS campus near Intake structure, all complete as per standards. (315 KVA Tranformer with complete installation.)

Air Break Switch : Supplying and erecting approved make thyrite H.T. outdoor type Gang Operated Air Break. Triple pole switch of required capacity with 3 post / pin type insulator per phase, mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps. etc. Suitable for 11 KV line Rotating Type

(Mechanical & Electrical at WTP)

Doing survey, Collecting field data, designing, getting it approved by competent authority and Clear water pumping Machinery with all complete job (Please refer to Section 5,Sl. 2.4 of SBD for detailed specification )

Clear water Pumpsets : Supplying, installation & commissioning of water lubricated, Horizontal spit casing/Multistage centrifugal pump [make: Kirloskar / WPIL / Mather & Platt] as per IS: 5120, capable for required discharge against total head coupled with energy effecient TEFC & IE3 squirrel cage induction motor conforming to IS: 325 & IS: 12615, operating on 415 V, 3 Phase, 50 C/S, A.C Supply having speed 1500 rpm having IE3 rating [make: Kirloskar / ABB / BHEL / CGL/Marathon] with a suitable Type coupling (UNIQUE make) and mounted on a common M.S.fabricated Base plate including construction of foundation, erection and doing alignment ,with pressure gauge, Suitable size of NR valves, Sluice valves, Butterfly Valve & foot valve and stainer, Piping work for Suction & Delivery line, common header & other piping works, standard fittings all complete as per site requirement and direction of E/I.

WTP to Part-1 :- Discharge = 3600 LPM, Head = 140 m (3W + 2S )

FASD STARTER : Supplying and errecting, assembled fully automatic star delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380 to 440 volts, 3 phase, 50 Hz with no volt coil, overload relay and ON OFF push buttons with necessary materials and connected to supply etc. all complete.

Power Distribution Panel : Supply, Installation and Commissioning of Power control cum distribution cubical panel board (LT Panel), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder- 1600 A TPN 415V ACB with thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/ SIEMENS/ Schneider- 1no.

b) Outgoing feeder- 5 nos. 500A TP 415V MCCB having thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/SIEMENS/ Schneider- with 1no. Spare feeder each.

c) Bus Bar- 4 pole 1600A 415V copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

f) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Green colour- 1set.

g) 32A MCB, 63A & 100A MCCB for light load, WTP and other utility loads of L&T/SIEMENS/ Schneider make- 2no each.

h) APFC panel of required and Suitable capacitor banks in standards stages with reactor coils for raising PF from 0.80 to 0.98,etc. all complete. Including motor control relays, earth fault relay, over/leakage current relay,etc. all other safety relays.

Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and including all type of relays with internally wired with suitable size of copper control wire/cable, etc. all complete.

Cables : Supplying , laying and suitably terminating both ends with following cables:-

(a) Cost of 400 Sq.M.M. x 3.5 core XLPE Aluminum armoured 1.1 KV grade cable including laying on cable tray from Transformer to LT Panel in the WTP pump house with suitable number of runs.

(b) Cost of 185 Sq.M.M. x 3.0 core XLPE 1.1 KV grade solid/ stranded armoured copper conductor with 6 mm thick cable including laying on wall/floor from LT Panel to Starter & Motors.

Lifting Equipment : Providing, erecting and commissioning of 3 Tonne single girder Hand Operated Circular/Rectangular Travelling Crane with 6 m lift complete with Chain pully Block ISI Marked and traveling trolly both tested for 50% over load including arrangement for longitudinal travel / Circular travel and cross travel with wheel , hand chain , etc. , all complete .

Earthing : Providing & erecting earthing for each motors and Stabiliser with suitable Copper earth plate, GI pipe, charcoal, salt, etc. all complete as per IE Rule.

Additional Items : Supplying and erecting lightening arrester for pump house 2 nos. Fire fighting system, emergency light with inverter and battery, display boards at pumphouse and ESS, safety gadgets e.g. hand gloves, gumboot, helmet, First aid box, insulation pad near each electrical controls and equipments, maintenance and measuring tools tools etc. as per requirement, standards and IE rule.

Electric Sub-Station ( ESS ):- supplying all materials e.g. different types of M.S channel M.S. angle, welded joint, nut bolts, Aluminum pipe for bus bar, Air break switch, 3 set horn gap fuses, Drop Out Fuse, LA, Transformers earthing complete set, Disc/ Pin insulator, fuse barrel, double core out door C.T / P.T, 3 sets lightening arrester and suitable VCB, etc. including the cost of fabrication, grouting & P.C.C. foundation block and providing safety arrangements, etc. for designing and constructing electric substation of suitable size and a suitable size switch room inside the ESS campus near WTP campus, painting, PCC flooring, making cable ducts, covering by RCC slabs/grilled cover after laying required cables and sand filling, doing boundary and grilling, making steel double door suitable size gate, punning, plastering, painting, etc and making and finishing plinth for installation of 1 Nos. 1000 KVA (11/0.415 KV) transformers, etc. all complete as per standards, IE rule and direction of E/I. 1000 KVA Transformer with all complete installation.

Air Break Switch : Supplying and erecting approved make thyrite H.T. outdoor type Gang Operated Air Break. Triple pole switch of required capacity with 3 post / pin type insulator per phase, mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps. etc. Suitable for 11 KV line Rotating Type

(Mechanical & Electrical at UG SUMP-01)

Doing survey, Collecting field data, designing, getting it approved by competent authority and Clear water pumping Machinery with all complete job (Please refer to Section 5,Sl. 2.4 of SBD for detailed specification )

Clear water Pumpsets : Supplying, installation & commissioning of water lubricated, Horizontal spit casing/Multistage centrifugal pump [make: Kirloskar / WPIL / Mather & Platt] as per IS: 5120, capable for required discharge against total head coupled with energy effecient TEFC & IE3 squirrel cage induction motor conforming to IS: 325 & IS: 12615, operating on 415 V, 3 Phase, 50 C/S, A.C Supply having speed 1500 rpm having IE3 rating [make: Kirloskar / ABB / BHEL / CGL] with a suitable Type coupling (UNIQUE make) and mounted on a common M.S.fabricated Base plate including construction of foundation, erection and doing alignment ,with pressure gauge, Suitable size of NR valves, Sluice valves, Butterfly Valve & foot valve and stainer, Piping work for Suction & Delivery line, common header & other piping works, standard fittings all complete as per site requirement and direction of E/I.

Intermediate UG SUMP-01 to Part-2 :- Discharge = 1800 LPM, Head = 100 m (1W + 1S )

Intermediate UG SUMP-01 to Zone-8 :- Discharge = 500 LPM, Head = 33 m (1W + 1S )

FASD STARTER : Supplying and errecting, assembled fully automatic star delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380 to 440 volts, 3 phase, 50 Hz with no volt coil, overload relay and ON OFF push buttons with necessary materials and connected to supply etc. all complete.

Power Distribution Panel : Supply, Installation and Commissioning of Power control cum distribution cubical panel board (LT Panel), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder- 400 A TPN 415V MCCB with thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/ SIEMENS/ Schneider- 1no.

b) Outgoing feeder- 200A TP 415V MCCB having thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/SIEMENS/ Schneider- 2no. and 1no. Spare feeder.

c) Outgoing feeder- 32A TP 415V MCCB having thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/SIEMENS/ Schneider- 2no. and 1no. Spare feeder.

d) Bus Bar- 4 pole 400A 415V copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

g) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Green colour- 1set.

h) 32A MCB and 63A MCCB for light load and other utility loads of L&T/SIEMENS/ Schneider make- 2no each.

i) APFC panel of required and Suitable capacitor banks in standards stages with reactor coils for raising PF from 0.80 to 0.98,etc. all complete. Including motor control relays, earth fault relay, over/leakage current relay,etc. all other safety relays.

Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and including all type of relays with internally wired with suitable size of copper control wire/cable, etc. all complete.

(a) Cost of 240 Sq.M.M. x 3.5 core XLPE Aluminum armoured 1.1 KV grade cable including laying on cable tray from Transformer to LT Panel in the WTP pump house with suitable number of runs.

(b) Cost of 50 Sq.M.M. x 3.0 core XLPE 1.1 KV grade solid/ stranded unarmoured copper conductor with 6 mm thick cable including laying on wall/floor from LT Panel to Starter & Motors.

(c) Cost of 6 Sq.M.M. x 3.0 core XLPE 1.1 KV grade solid/ stranded unarmoured copper conductor with 6 mm thick cable including laying on wall/floor from LT Panel to Starter & Motors.

Lifting Equipment : Providing, erecting and commissioning of 3 Tonne triple spur gear type Chain Pulley Block suitable for capacity as below with 6 m lift complete with load chain and hand chain suitable for above lift, tested to 50% over load as per IS 3832 carrying ISI mark., etc. , all complete .

Earthing : Providing & erecting earthing for each motors and Stabiliser with suitable Copper earth plate, GI pipe, charcoal, salt, etc. all complete as per IE Rule.

Lighting : Supplying and doing electrical wiring and internal and external lighting i.e. Lighting for entire plant area at clear water plant with LED luminaries as required and as per direction of E/I.

Additional Items : Supplying and erecting lightening arrester for pump house 2 nos. , Fire fighting system, emergency light with inverter and battery, display boards at pumphouse and ESS, safety gadgets e.g. hand gloves, gumboot, helmet, First aid box, insulation pad near each electrical controls and equipments, maintenance and measuring tools tools etc. as per requirement, standards and IE rule.

Air Break Switch : Supplying and erecting approved make thyrite H.T. outdoor type Gang Operated Air Break. Triple pole switch of required capacity with 3 post / pin type insulator per phase, mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps. etc. Suitable for 11 KV line Rotating Type

(Mechanical & Electrical at UG SUMP-02)

Doing survey, Collecting field data, designing, getting it approved by competent authority and Clear water pumping Machinery with all complete job (Please refer to Section 5,Sl. 2.4 of SBD for detailed specification )

Clear water Pumpsets : Supplying, installation & commissioning of water lubricated, Horizontal spit casing/Multistage centrifugal pump [make: Kirloskar / WPIL / Mather & Platt] as per IS: 5120, capable for required discharge against total head coupled with energy effecient TEFC & IE3 squirrel cage induction motor conforming to IS: 325 & IS: 12615, operating on 415 V, 3 Phase, 50 C/S, A.C Supply having speed 1500 rpm having IE3 rating [make: Kirloskar / ABB / BHEL / CGL] with a suitable Type coupling (UNIQUE make) and mounted on a common M.S.fabricated Base plate including construction of foundation, erection and doing alignment ,with pressure gauge, Suitable size of NR valves, Sluice valves, Butterfly Valve & foot valve and stainer, Piping work for Suction & Delivery line, common header & other piping works, standard fittings all complete as per site requirement and direction of E/I.

Intermediate UG SUMP-02 to Part-3 :- Discharge = 2450 LPM, Head = 125 m (1W + 1S )

FASD STARTER : Supplying and errecting, assembled fully automatic star delta starter, in a provided cubical panel to operate squirrel cage induction motor working on 380 to 440 volts, 3 phase, 50 Hz with no volt coil, overload relay and ON OFF push buttons with necessary materials and connected to supply etc. all complete.

Power Distribution Panel : Supply, Installation and Commissioning of Power control cum distribution cubical panel board (LT Panel), made of 2 mm thick, MS sheet of suitable size, dust and vermin proof consisting of following accessories.

a) Incoming feeder- 400 A TPN 415V MCCB with thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/ SIEMENS/ Schneider- 1no.

b) Outgoing feeder- 315A TP 415V MCCB having thermal release range, adjustable and breaking capacity with rotary operating mechanism handle of make L&T/SIEMENS/ Schneider- 2no. and 1no. Spare feeder.

c) Bus Bar- 4 pole 400A 415V copper strip bus bar enclosed in MS sheet, etc. all complete job- 1no.

f) Indicating lamp LED - L&T/SIEMENS make in Red, Yellow and Green colour- 1set.

g) 32A MCB and 63A MCCB for light load and other utility loads of L&T/SIEMENS/ Schneider make- 2no each.

h) APFC panel of required and Suitable capacitor banks in standards stages with reactor coils for raising PF from 0.80 to 0.98,etc. all complete. Including motor control relays, earth fault relay, over/leakage current relay,etc. all other safety relays.

Panel should be duly painted with two coats super enameled paint of approved colour one coat of red oxide primer and including all type of relays with internally wired with suitable size of copper control wire/cable, etc. all complete.

Cables : Supplying , laying and suitably terminating both ends with following cables:-

(a) Cost of 240 Sq.M.M. x 3.5 core XLPE Aluminum armoured 1.1 KV grade cable including laying on cable tray from Transformer to LT Panel in the WTP pump house with suitable number of runs.

(b) Cost of 70 Sq.M.M. x 3.0 core XLPE 1.1 KV grade solid/ stranded unarmoured copper conductor with 6 mm thick cable including laying on wall/floor from LT Panel to Starter & Motors.

Lifting Equipment : Providing, erecting and commissioning of 3 Tonne single girder hand opreted circular /Rectangular travelling crane with 6 m lift complete with chainpully block ISI marked and travelling trolly both tested for 50% over load including arrangement for longitudional travel/ circular travel and cross travel with wheel hand chain etc. all complete.

Earthing : Providing & erecting earthing for each motors and Stabiliser with suitable Copper earth plate, GI pipe, charcoal, salt, etc. all complete as per IE Rule.

Lighting : Supplying and doing electrical wiring and internal and external lighting i.e. Lighting for entire plant area at clear water plant with LED luminaries as required and as per direction of E/I.

Additional Items : Supplying and erecting lightening arrester for pump house 2 nos. , Fire fighting system, emergency light with inverter and battery, display boards at pumphouse and ESS, safety gadgets e.g. hand gloves, gumboot, helmet, First aid box, insulation pad near each electrical controls and equipments, maintenance and measuring tools tools etc. as per requirement, standards and IE rule.

Air Break Switch : Supplying and erecting approved make thyrite H.T. outdoor type Gang Operated Air Break. Triple pole switch of required capacity with 3 post / pin type insulator per phase, mounted in horizontal or vertical position on provided cross arm with adequate length of G.I. pipe for operating handle erected on extended square shaft. the operating handle provided with lock and key at suitable height from ground with necessary clamps. etc. Suitable for 11 KV line Rotating Type

Raw Water Rising Main

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Raw water Rising Main (Please refer to Section 5,Sl. 3.1 of SBD)

Earth Work in excavation (As per I.S. 3114/1965) for laying of Different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and life asper specification and direction of Engineer in-charge (b) For classification of soil item -B

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge (for classification of Soil item A & B)

Supplying centrifugally cast (spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS8329/2000 in standard lengths of class K-9 suitable for push on joint (Rubber gasket jointing) with cement mortar lining on inside surface and out side zinc coating with bituminous paint including all other taxes insurance including inspection charges and all taxes all complete . (500 mm Dia DI)

Providing and supplying ISI standard D.I. specials & fitting with sealing rubber gasket of S.B.R. complete with cast iron follower gland and M.S. nut & bolts coated or otherwise protected from rusting and suitable for D.I. pipes including ED, CST, all taxes, etc. coplete as per I.S. 9523 but excluding frieght.

Providing R.C.C.M- 200 with nominal mix of (1:1.5:3) in columns with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including shuttering screening mixing cement concrete in mixer and placing in position vibrating striking , curing , taxes and royalty all complete as per building specification and direction of Engineer - in - charge .

Supplying labours, tools , tackles, lubricant etc for laying and jointing DI / C.I.S/S Tyton pipes (class LA) trenches supplying ( confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard ,barrier and red light to safe guard against accident ,all complete and laying of pipes is to be done as per (I.S.S.3114-1985) as per design ,specification and direction of E./I. Without rubber gasket .

Supplying Labour ,tools and tackles for testing of laid C.I / DI or U.P.V.C or H.D.P.E or A.C pressure pipe up to 60 meter head of water all complete as per specification andection of E/I

Providing Tor steel rainforcement of 10 mm, 12 mm and 16 mm dia bars as per approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending, and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying , necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I

Providing Double Flanged Sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. complete . (without bypass) with E.D PN 1.6

150 mm Scour Valve

Supplying Labour and tools for fixing C.I. sluice valve in trenches with a pair of C.I. Tail piece including making lead caulked joints and flanged joints as per I.S.S. specification,including supplying all jointing materials (Pig lead confirming to I.S.S. 782-1978, yarn confirming to I.S.S. 6587– 1972 and nuts and bolts confirming to I.S.S.1364 –1983) including drilling holes in flanges if required as per specification and direction of E/I.

150 mm Scour Valve

Providing and supplying air valves as per I.S. - 14845-2000 and M J P’s standard specifications double orifice type combined with isolating sluice valve, mounted in horizontal position and operated by wheel gearing, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seting on moulded seat ring, inlet face and drilled, including all taxes (central and local), insurance, third party inspection charges, loading, unloading, transportation upto departmental storer Excluding GST Levied by GOI and GOM and all Respect etc. complete .

Lowering, laying and fixing in proper alignment and position all types of C.I. air valves as directed by Engineer –in–charge including cost of conveyance from store to site of work, cost of all material and giving satisfactory hydraulic testing etc. complete.

Providing and supplying ISI Mark CI/DF Reflax Valves Non Return Valve of Following Dia Including all Taxes such as GST Leveed by GOI and GOM in all Respect railway freight inspection charge unlodeing from railway wagon , Loading into Truck Transportation upto departmental stroes/ Site unloading staciking etc. Complete . Reflax Valves as per IS 5312 Part-1 (1984)

Lowering, laying and jointing in position Following CI /DFReflex Valves /Buttery Fly Valves and Sluice Valve including cost of all labour jointing material , including nut bolt and giving satisfactroy hydraulic testing etc complete (rate for all class of Valves) .

Supply all materials & construction of Thrust Block where required .

Construction of B .W . masonry valve chamber .

Boundary wall with Gate (2030 RMT) including 14 Nos. Gate

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authority Construction of Compound wall for WTP , ESR , Sump , etc. all complete job.(Please refer to Section 5,Sl. 2.9 of SBD)

Earth work in excavation in foundation trenches in hard soil (Vide classification soil item B) and disposal of excavated earth as obtained to a distance up to 50 Mtr including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, specification and direction of E/I

Providing coarse clean sand in filling in fundation trenches or in plinth including ramming and watering in layers not exceeding 15mm thick with all leads and lifts includiing cost of all materials, labour, royality and taxes all complete as per building specification and direction of E/I.

Providing designation of 75A one brick flat soling, joints filled with local sand including cost of watering, taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and shuttering

Providing R.C.C M - 200 with nominal mix of (1:1.5:3) in foundation with approved quality of stone chips (20mm to 6mm size) clean course sand of F.M 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Centering and shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in stiffeners with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I.

Centering and shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at plinth level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering and shuttering

Providing RCC M-200 with nominal mix of (1:1.5:3) in band at lintel level with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M 2.5 to 3 including curing, shuttering carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement) taxes and royalty, all complete as per building specification and direction of E/I. Top of Wall

Centering and shuttering

Providing designation 75 A brick work in CM (1:6) in super structure with approved quality of clean coarse sand of FM 2 to 2.5 including, providing 10mm thick mortar joints cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of FM 1.5 including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification & direction of E/I. Qnty. Same as Item no.13

Providing Tor steel reinforcement of 10 mm ,12 mm , &16 mm dia Bars as per approved design and drawing excluding carriage of M.S bars to work site , cutting ,bending and binding with annealed wire with cost of wire ,removal of rust , Placing the rods in position all complete as per building specification and direction of E/I

Filling in foundation trenches and plinth in layers not exceeding dressed with earth obtained from excavation of foundation trenches with a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I

Supplying fitting & Fixing M.S. grill gate with M.S. grills made 20x6mm M.S. flat or 16mm M.S. square bars fitted 25x25x6 mm M.S. angle frame of size 60x60x6 mm including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C (1:2:4) blocks of required size, applying a priming red lead paint over steel work , taxes all complete as per drawing specification and direction of E/I.

Providing two coat of painting with ready mixed paint of approved shade and make over steel surface

Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 6 KM lead

Stone/Stone Chips 11 KM lead

Water Treatment Plant (W.T.P.)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and necessary equipment for designing & construction of Conventional WTP of 16.00 MLD capacity. With all complete job. (Please refer to Section 5,Sl. 2.3 of SBD)

Cost of 16.00 MLD Water Treatment Plant

R.C.C Riser for Rising Main(200 Nos.)

E/W in excavation in foundation trenches in ordinary soil (vide classification of soil item-A ) & disposal of excavated earth as obtained to a distance upto 50 M including all lifts, levelling ,ramming the foundation trenches, removing roots of trees, shurbs all complete as per approved design ,building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming & watering in layers not exceeding 150 mm thick with all leads and lift including cost of all materials, labour, royalty and taxes all complete as per building specification & direction of E/I. (mode of measurement compacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C.M - 100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade - III (50 mm to 25 mm size) clean coarse sand of F.M. 2.5 to 3 including screening , shuttering,mixing cement concrete in mixer & placing in position, vibrating, striking , curing, taxes & royalty all complete as per building specification & direction of Engineer-in-charge

Providing RCC M-200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M.2.5 to 3 including screening, shuttering , mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement), taxes and royalty all complete, as per building specification and direction of E/I.

Centering and shuttering

Providing R.C.C.M- 200 with nominal mix of (1:1.5:3) in columns with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including shuttering screening mixing cement concrete in mixer and placing in position vibrating striking , curing , taxes and royalty all complete as per building specification and direction of Engineer - in - charge .

Centering and shuttering

Providing Tor steel rainforcement of 10 mm, 12 mm and 16 mm dia bars as per approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending, and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I.

Providing 12 mm thick cement plaster (1:4) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water ,scaffolding taxes and royalty all complete as per building specification & direction Of E/I.

Carriage of materials from different sources or departmental stores to work site including loading, transporting, unloading and stacking the materials at work site etc. all complete job. as per direction of E/I.

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Stone/Stone chips 11 KM lead

Clear Water Rising Main

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Laying of Clear water Rising Main (Please refer to Section 5,Sl. 3.1 of SBD)

Earth Work in excavation (As per I.S. 3114/1965) for laying of Different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and life asper specification and direction of Engineer in-charge (b) For classification of soil item -B

Earth work in excavation of foundation trenches as per design section in ordinary or soft rock (where blasting is not required and disposal of excavated materials so obtained (50 m away from the edge of the trenches ) with initial lead of 150 m and initial lift of 1.5 m as per specification amnd direction of E/I.

Supplying tools and cutting road as well restoring the same as per specificat i o n and direction of E/I a) Pucca Road (Except Black top only taken out material to be used) for cutting road as per requirement.

Water Bound Macadam road (taken out material will be used) for cutting road as per requirement

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15 meter lead and disposal of un-serviceable materials with all leads all complete as per direction of E./I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm -6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening shuttering mixing cement concrete in mixer and placing in position vibrating Striking curing taxes and royalty all complete as per building specification and direction of E/I.

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge (for classification of Soil item A & B)

Supplying centrifugally cast (spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS8329/2000 in standard lengths of class K-9 suitable for push on joint (Rubber gasket jointing) with cement mortar lining on inside surface and out side zinc coating with bituminous paint including all other taxes insurance including inspection charges and all taxes all complete

Providing and supplying ISI standard D.I. specials & fitting with sealing rubber gasket of S.B.R. complete with cast iron follower gland and M.S. nut & bolts coated or otherwise protected from rusting and suitable for D.I. pipes including ED, CST, all taxes, etc. coplete as per I.S. 9523 but excluding frieght.

100 mm to 300 mm

350 mm to 450 mm

Supplying labours, tools , tackles, lubricant etc for laying and jointing DI / C.I.S/S Tyton pipes (class LA) trenches supplying ( confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard ,barrier and red light to safe guard against accident ,all complete and laying of pipes is to be done as per (I.S.S.3114-1985) as per design ,specification and direction of E./I. Without rubber gasket .

Supplying Labour ,tools and tackles for testing of laid C.I / DI or U.P.V.C or H.D.P.E or A.C pressure pipe up to 60 meter head of water all complete as per specification andection of E/I

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying , necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I

Providing Double Flanged Sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. complete . (without bypass) with E.D PN 1.6

100 mm Scour Valve

150 mm Scour Valve

Supplying Labour and tools for fixing C.I. sluice valve in trenches with a pair of C.I. Tail piece including making lead caulked joints and flanged joints as per I.S.S. specification,including supplying all jointing materials (Pig lead confirming to I.S.S. 782-1978, yarn confirming to I.S.S. 6587– 1972 and nuts and bolts confirming to I.S.S.1364 –1983) including drilling holes in flanges if required as per specification and direction of E/I.

100 mm Scour Valve

150 mm Scour Valve

Providing and supplying air valves as per I.S. - 14845-2000 and M J P’s standard specifications double orifice type combined with isolating sluice valve, mounted in horizontal position and operated by wheel gearing, small orifice elastic ball resting on a gun metal orifice nipple, large orifice vulcanite ball seting on moulded seat ring, inlet face and drilled, including all taxes (central and local), insurance, third party inspection charges, loading, unloading, transportation upto departmental storer/ site, etc. complete .

(Single Ball Flanged Type Air Valve P.N 1.6 Dia-25 mm (From 100mm to 150 mm )

(Single Ball Flanged Type Air Valve P.N 1.6 Dia-50 mm (From 200mm to 250 mm )

(Double Ball Flanged Type Air Valve P.N 1.6 Dia-100 mm (From 300mm to 350 mm )

Lowering, laying and fixing in proper alignment and position all types of C.I. air valves as directed by Engineer –in–charge including cost of conveyance from store to site of work, cost of all material and giving satisfactory hydraulic testing etc. complete.

(Single Ball Flanged Type Air Valve P.N 1.6 Dia-25 mm (From 100mm to 200 mm )

(Single Ball Flanged Type Air Valve P.N 1.6 Dia-50 mm (From 250mm to 350 mm )

(Double Ball Flanged Type Air Valve P.N 1.6 Dia-100 mm (From 400mm to 450 mm )

Providing, installing and giving satisfaction field testing of flanged ends Bulk water meter of following type and as mentioned below in (a) and (b) with FGI - 250 cast iron body, class "B" confirming to I.S. 2373 or as per ISO 4064, marked to read in metric system, along with manufacturer's test a n d guarantee certificate including cost of all material with ISI mark or EEC mark Enclosed type as per IS2373

Supply all materials & construction of Thrust Block where required as per enclosed Annexure-2

Construction of B .W . masonry valve chamber as per enclosed annexure

Elevated Service Reservoir (ESR's)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of ESR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

(ESR-01 Capacity - 190 K.L., Staging - 21.00 m)

(ESR-02 Capacity - 230 K.L., Staging - 23.00 m)

(ESR-03 Capacity - 520 K.L., Staging - 22.00 m)

(ESR-04 Capacity - 560 K.L., Staging - 18.00 m)

(ESR-05 Capacity - 300 K.L., Staging - 20.00 m)

(ESR-06 Capacity - 710.00 K.L., Staging - 22.00 m)

(ESR-07 Capacity - 310.00 K.L., Staging - 22.00 m)

(ESR-08 Capacity - 190 K.L., Staging - 22.00 m)

(ESR-09 Capacity - 380 K.L., Staging - 15.00 m)

(ESR-10 Capacity - 400 K.L., Staging - 20.00 m)

Ground Service Reservoir (GSR)

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of GSR all complete job. (Please refer to Section 5,Sl. 2.8 of SBD)

Capacity of GSR 390 KL

Intermediate Under Ground SUMP

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labours and equipment for designing & construction of Ground Service Reservoir (SUMP) all complete job. (Please refer to Section 5,Sl. 2.8.1 of SBD)

Capacity of UG Sump-01 of 400 KL

Capacity of UG Sump-02 of 400 KL

Distribution System

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Providing all labour, materials, equipment to procure and laying of DI class K-7 pipes with Cement Mortar Lining for distribution main (Please refer to Section 5,Sl. 3.1 of SBD)

Earth Work in excavation (As per I.S. 3114/1965) for laying of Different types and size of pipes so as to give one meter average cover over the socket of pipe with disposal of excavated earth within initial lead and life asper specification and direction of Engineer in-charge (b) For classification of soil item -B

Earth work in excavation of foundation trenches as per design section in ordinary or soft rock (where blasting is not required and disposal of excavated materials so obtained (50 m away from the edge of the trenches ) with initial lead of 150 m and initial lift of 1.5 m as per specification amnd direction of E/I.

Supplying tools and cutting road as well restoring the same as per specificat i o n and direction of E/I a) Pucca Road (Except Black top only taken out material to be used) for cutting road as per requirement.

Water Bound Macadam road (taken out material will be used) for cutting road as per requirement

Dismantling plain cement or lime concrete work including stacking serviceable materials in countable stacks within 15 meter lead and disposal of un-serviceable materials with all leads all complete as per direction of E./I.

Providing PCC M-150 in nominal mix of (1:2:4) in foundation with approved quality of stone chips 20 mm -6 mm size graded and clean coarse sand of FM 2.5 to 3.0 including screening shuttering mixing cement concrete in mixer and placing in position vibrating Striking curing taxes and royalty all complete as per building specification and direction of E/I.

Earthwork in back filling the trenches after laying different types and sizes of pipes with earth removed during excavation within initial lead and lift as per specification and direction of Engineer-in-Charge (for classification of Soil item A & B)

Supplying centrifugally cast (spun) ductile iron pressure pipe for water supply with socket and spigot ends confirming to IS8329/2000 in standard lengths of class K-7 suitable for push on joint (Rubber gasket jointing) with cement mortar lining on inside surface and out side zinc coating with bituminous paint including all other taxes insurance including inspection charges and all taxes all complete

Providing and supplying ISI standard D.I. specials & fitting with sealing rubber gasket of S.B.R. complete with cast iron follower gland and M.S. nut & bolts coated or otherwise protected from rusting and suitable for D.I. pipes including ED, CST, all taxes, etc. coplete as per I.S. 9523 but excluding frieght.

Supplying labours, tools , tackles, lubricant etc for laying and jointing DI / C.I.S/S Tyton pipes (class LA) trenches supplying ( confirming to I.S.S.-5382-1969) and making gasket joints including providing night guard ,barrier and red light to safe guard against accident ,all complete and laying of pipes is to be done as per (I.S.S.3114-1985) as per design ,specification and direction of E./I. Without rubber gasket .

Supplying Labour ,tools and tackles for testing of laid C.I / DI or U.P.V.C or H.D.P.E or A.C pressure pipe up to 60 meter head of water all complete as per specification andection of E/I

Labour charge for one cutting of C.I/ D.I and specials including suppying supplying , necessary tools and plants ,chipping or filling the surface finish as per specification and direction of E/I

Providing Double Flanged Sluice valve confirming for IS 2906/14846 including worn gear arrangements as per test pressure stainless steel spindle, caps including all transportation etc. complete . (without bypass) with E.D PN 1.0

Scour Valve 100 mm

Scour Valve 150 mm

Supplying Labour and tools for fixing C.I. sluice valve in trenches with a pair of C.I. Tail piece including making lead caulked joints and flanged joints as per I.S.S. specification,including supplying all jointing materials (Pig lead confirming to I.S.S. 782-1978, yarn confirming to I.S.S. 6587– 1972 and nuts and bolts confirming to I.S.S.1364 –1983) including drilling holes in flanges if required as per specification and direction of E/I.

Scour Valve 150 mm

Scour Valve 100 mm

Construction of B .W . masonry valve chamber .

Staff Quarters

Doing Geotechnical survey, Collecting field data, designing, getting it approved by competent authorityand Provision of twin type Staff Quarter etc. all complete job.(Please refer to Section 5,Sl. 2.6 B of SBD) - 1 Unit

E/W in excavation in foundation renches in ordinary soil (vide classification of soil i t e m - A) and disposal of excavated earth obtained to a distance upto 50 M including all lift leveling, ramming the foundation trenches removing roots of trees,shurbs all complete as per approved design,building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming & watering in layers not exceeding 150 mm thick with all leads and lift including cost of all materials, labour, royalty and taxes all complete as per building specification & direction of E/I.(mode of measurement compacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing P.C.C.M -100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade-III (50 mm to 25 mm size) clean coarse sand of F.M. 2.5to 3 including screening,shuttering ,mixing,cement concrete in mixer & placing in position, vibrating, striking, curing, taxes & royalty all complete as per building specification & direction of Engineer-in-charge.

Providing designation 75 A brick work in C.M. (1:6) in foundation &plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10 mm thick mortar joints, cost of screening materials, raking out joints to 15 mm depth,curing,taxes& royalty all complete as per building specification & direction of E/I.

Providing 25 mm thick damp proof coarse with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6 mm size graded and clean coarse sand of F.M.2.5 to 3 including screening, shuttering, mixing cement concrete in mixer with 5 % cico or any other approved water proofing compound and placing in position, striking, curing ,taxes & royalty all complete as per building specification &direction of E/I

Providing designation 75 A brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M . 2.0 to 2.5 including providing 10 mm thick mortar joints, cost of screening, materials, scaffolding, raking out joints to 15 mm depth curing, taxes & royalty all complete as per building specification & direction of E/I.

Providing R.C.C.M- 150 with nominal mix of (1:2:4) in lintel with approved quality of stone ships 20 mm to 6 mm.size graded & clean coarse sand of F.M .2.5 to 3 including screening, centering, shuttering ,mixing cement concrete in mixer & placing in position vibrating, striking, curing (but excluding the cost of reinforcement), taxes & royalty all complete, as per building specification and direction of E/I.

Centering and shuttering

Providing average 63 mm thick R.C.C.M-150 with nominal mix of (1:2:4) chajja with approved quality of stone chips 20 mm to 6 mm size graded &clean coarse sand of F.M. 2.5 to 3 including making drip course in concrete, screening ,centering, shuttering & mixing cement concrete in mixer & placing in position vibrating,striking, 6 mm cement plaster (1:4) in ceiling & sides of chajja with sand of F.M. 1.5,curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification of E/I.

Centering and shuttering

Centering and shuttering

Providing R.C.C. M-200 with nominal mix of (1:1:5:3) in roof slab with approved quality of stone ships 20 mm to 6 mm size Graded & clean coarse sand of FM 2.5 to 3.0 including screening,centering,shuttering ,mixing cement concrete in mixer & placing in position, vibrating,striking, curing (but excluding the cost of reinforcement) taxes &royalty all complete as per building specification&direction of the E/I.

Centering and shuttering

Supplying, fitting & fixing good quality, well dressed & well seasoned sal wood work in chaukhat in doors, windows, skylights, fanlights and C/W celestial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls & lintels all complete as per building specification & direction of the E/I.

Supplying fitting and fixing 250 x 20 x 6 mm L-type M.S. Clamp properly fish tailed, including making holes and setting the same in 375 x 125 x75 mm cement concrete block (1:2:4) with cost of all labour and materials and taxes as per building specification and direction of E/I .

Supplying fitting & fixing 38 mm thick good quality well dressed and well seasoned Sal wood battened shutter ledged & braced in doors and windows with oxidized iron fitting such as hinges, sliding door bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand block as per schedule, taxes & royalty all complete as per building specification& direction of Engineer –in- Charge

Supplying, fitting & fixing M.S. Grill made of 20 x 6 cmm M.S. Flat as per approved design & drawing properly fabricated with Joints continuous fillet welded and finished smooth, carriage of grill to work site, hoisting as per the building specification and direction of E/I. (where materials is not supplied by the Deptt.)

Providing 25 mm thick precast R.C.C. M-150 with nominal mix of (1:2:4) jali with approved quality of stone chips of 6 mm nominal size and clean coarse sand of FM 2.5 to 3 with 1.6 mm thick M.S.wire as per approved design and drawing and placing the same in position true to plumb and level and properly grouted with cement mortar (1:3) including cost of curing, scaffolding and finishing all complete as per building specification and direction of E/I.

Providing and fixing fan hook of16 mm dia M.S. bar 1 meter long bent to required size and shape, placed in position and fixing in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/I. (where material is not supplied by Deptt.).

Supplying,fitting and fixing M.S. grill gate with M.S. grills made of 20 x 6 mm M.S. flats or 16 mm .M.S.square bars fitted on 25x 25x6mm. M.S. Angle frame of size 60x60x6mm including cost off abrication,providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size,applying priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I. (when steel is not supplied by the Deptt.)

Providing 6 mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads & lifts of water, scaffolding, taxes & royalty all complete as per building specification & direction of E/I.

Providing 12 mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, Curing with all leads & lifts of water, scaffolding, taxes and royalty all complete as per building specification & direction of E/I.

Providing 12 mm.cement plaster (1:3) with clean coarse sand of F.M.1.5 including screening, curing with all leads &lifts of water,scaffolding, taxes and royalty all complete as per building specification & direction of E/I.

Filling in foundation trenches &plinth in layers not exceeding 150 mm.thick well watered, rammed, fully compacted &fine dressed with earth obtained from excavation of foundation trenches withi a lead of 50 M & lift of 1.5 M all complete as per building specification & direction of E/I. (Mode of measurement compacted volume).

Providing 25 mm thick first class patent stone flooring (1:2:4) with stone chips in two layers, bottom layer 19 mm thick (1:2:4) with 12 mm to 6 mm size graded stone chips and top layer 6 mm thick (1:2) with 6 mm down stone chips, in panels including cost of curing, finishing the surface smooth by rubbing with carborandum stone, taxes & royalty with all complete as per building specification & direction of E/I.

Providing designation 75 A brick on edge flooring in cement mortar (1:4) with top surface flush pointed in cement mortar (1:4) with approved quality of sand including the cost of curing, taxes, royalty all complete as per building specification and direction of E/I.

Providing two coat of snowcem of approved shade and make over a coat of cement of primer on new surface including preparing the plasterded surface smooth with sand paper, scaffolding, curing and taxes all complete as per building specification and direction of E/I.

Colour washing two coats over a coat of white wash over new surface with approved quality of lime including cost of cleaning surface thoroughly and removing the scales of smoke & mosh marks with jhama rubbing, scaffolding, washing, of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of painting with ready mixed paint over a coat of primer of approved shade and make over new wooden surface including preparing the surface after cleaning, removing dirt, scales, smokes, grease and sand papering, including cost of scaffolding and taxes all complete as per building specification & direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales, smokes and grease and cleaning the surface thoroughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (mode of measurement area shall be multiplied by the coefficient as indicated in building specification).

Providing two coats of painting with ready mixed paint of approved shade & make over steel surface including cleaning the surface thoroughly ,scaffolding & taxes all complete as per building specification & direction of E/I.

Providing Tor steel reinforcement of 10 mm, 12 mm and 16 mm dia bars as per approved design and drawing excluding carriage of M.S. bars to work site, cutting, bending, and binding with annealed wire with cost of wire, removal of rust, placing the rods in position all complete as per building specificati n and direction of E/I.

Cement 10 KM lead

Steel 10 KM lead

Sand 36 KM lead

Bricks 6 KM lead

Stone/Stone chips 11 KM lead

Metal 11 KM lead

(B) Water Supply and Sanitation Installation (Plumbing Work) -

Supplying and laying GI pipes of approved make in trenches with red lead and yarn with socket and screw joints and cutting pipes in size and threading ends where necessary including carriage of materials up to work site etc. all complete as per specification and direction of E/I.

i) 25mm GI. Pipe.

ii) 15 mm GI. Pipe.

Supplying materials and labours for fixing GI Pipes with red lead paints and yarn with screwed and sockted joints on wall, celling and floor including supplying of wall hooks of pipe clamp, wooden plugs, cutting pipe to size and threading ends where necessary all complete as per specification and direction of E/I.

i) 15 mm GI. Pipe

Supplying, fitting and fixing of GM ferrule of approved make in DI/CI main including drilling and tapping CI/DI main etc. all complete as per specification and direction of E/I.

Supplying and fixing GI fittings of approved make all complete as per direction of E/I.

(a) Elbow 15 mm dia

(b) Tee plane 15mm dia

(c) Nipple 15mm dia.

(d) Union Socket 25mm dia

(e) Union Socket 15mm dia

(f) Brass bib cock 15mm dia

(g) C.I stop cock 15mm dia

(h) C.I. stop cock 25mm dia

(i) Reducing Socket 25x15mm

(j) Tee 25x25x15mm dia

Supplying, fitting and fixing vitreous white glazed earthen were I W C of parry Hindustan or any other I.S.S approved make with 100 mm HCI ‘P’ trap, 15 Liters CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings C.I. or C.C brackets, 32 mm, alkathene /PVC telescopic flush pipe about 2 mtrs. long with one brass coupling and clamps, GI chain and pull including supplying and fixing a pair of vitreous white glazed earthen were footrest to be fixed in floor, 15 mm .CI body brass spindle, stop cock of weight not less than 50 grams, 15 mm. PVC connection pipe 450 mm. long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and irection of E/I. (510mm.long with 12.5 Liter low level PVCSystem).

Septic Tank and Soak Pit

Earth work in excavation in foundation trenches in ordinary soil (vide classification of soil item-B) and disposal of excavated earth as obtained to a distance up to 50 m including all lifts, leveling, ramming the foundation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of E/I.

Providing designation 75A one Brick flat soling, joints filled with local sand including cost of watering, tax, royalty all complete as per building specification and direction of E/I.

Providing P.C.C M150 with nominal mix of (1:2:4) in foundation with approved stone chips 20mm to 6mm size well graded and clean course sand of FM-2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, Vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing water proof cement plaster (1:3) with clean course sand of F.M- 1.5mm with 5% cico or any other approved water proofing compound including taxes and royalty all complete as per building specification and directions of E/I.

19 mm thick

Providing designation 75A bricks work in C.M. in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm. thick mortar joints, cost of screening materials racking out joints to 15 mm. depth, curing taxes and royalty all complete as per building specification and direction of E/I.

B/W in C.m (1:4)

B/W 75-B in (1:6) for soak pit

Brick work in dry masonry for soakpit

Providing pre cast R.C.C. M-150 with nominal mix of (1:2:4) slab of desired size with approved quality of stone chips and clean coarse sand of FM 2.5 to 3 including curing, shuttering, carrying the slab manually to site and laying in position all complete (but excluding the cost of reinforcement), taxes and royalty etc. all complete as per building specification and direction of E/I.

Providing for reinforcement as per approved design and drawing excluding carriage of tor rod to work site including cutting bending and binding with annealed wire with cost of wire removal of rust placing the rods in position all complete as per Specification and direction of E/I.

Supplying fitting and fixing P.V.C. Pipe/ P.V.C.fitting of approved make including earth work or providing scaffolding as the case may be all complete as per specification and direction of E/I.

100 mm dia HCI Band

Supplying materials and labours and fixing 20mm dia M.S bar steps in wall of 0.3 m interval and staggered in (1:2:4) cement concrete including scaffolding and curing etc. all complete as per specification and direction of E/I.

Supplying all materials, labours, tools and tackles and 100mm dia R.C.C hume pipe and laying jointing, testing, earth work including carriage of materials etc. all complete.

Supplying 50mm size brick bats and filling in soak pit including carriage and labours etc. all complete as per direction of E/I.

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750mm deep, 600x450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600x475 mm G.I. Cover With frame ( Weight not less than 36 Kg.) along with earth work in excavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I

Carriages of materials

Carriage of materials from divisional store or kiln site or quarry site to work site including contract profit,loading ,unloading , transportation, etc. all complete.

Cement 10 KM lead

Sand 36 KM lead

Stone chips 11 KM lead

Bricks 6 KM lead

Steel 10 KM lead

Electrical Works

Wiring for light point with 1.5 sq. mm pvc insulated multi stand copper conductors cable on surface pvc casing capping as required

Short point

medium point

long point

Wiring for fan point with 1.5 sq mm pvc insulated M/S copper conductor cable on surface pvc casing capping as required long point

Wiring for 5 pin 5 amp. plug point with 1.5 sq. mm pvc insulated M/S copper conductors cable on surface pvc casing capping including P/F 5 pin 5 amp. socket outlet and 5 amp. switch earthling the 3rd pin etc as per required.

Wiring for 3 pin 15 amp. plug point with 4 sq. mm pvc insulated M/S copper conductor cable on surface pvc cashing capping including P/F 3 pin 15 amp. switch socket combined earthling the 3rd pin as required Extra long point

Wiring for circuit wiring with 2x2.5 sq, mm pvc insulated M/S copper conductor cable on surface pvc casing capping as required.

Wiring for sub main with 2x 10 sq. mm pvc insulated M/S copper conductor cable on surface pvc casing capping including connections as required.

S/F 32 amp. hush type D.P switch including connection etc as required.

S/F 32 amp. main switch fuse unit including holes on the band connection and earthling the body as required

S/F batten or angle holder complete including connection etc. as required

S/F twin twisted flexible wire for connection of tube light and fan as required.

S/F following size sun mica sheet cutting and fixing under switch socket

S/F indicator light as required

S/F fuse on the board as required

S/F earthling with earth plate 600 x 600 x 30mm thick with masonry enclosures on the top as required

Extra for wiring salt and charcoal for copper earthling as required.

S/F bulk head fitting suitable for 100 watt lamp as required.

Earthing with G.I. earth pipe 4.5 M long 40mm dia including accessories and providing masonry enclosure with copper plate having locking arrangement and watering pipe etc with charcoal ,salt all complete as per electrical rule

Supplying ,fitting and fixing 5 amp ceiling rose on the existing junction

House Connection (24056+145=24201)

Doing survey Data Collection of FHTC Details including ADHAR No. with SBM ID etc.

Earth work in excavation in foundation trenches in hard soil vide classification item-B and disposal of excavated earth as obtained to a distance upto 50 m including all lifts,levelling,ramming the foundation trenches,removing roots of trees,shrubs all complete as per approved design,building specifications and direction of E/I.

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials labours , royalty and taxes all complete as per building specification and direction of E/I.(mode of measurement compacted volume)

Providing P C C M-150 in nominal mix of (1:2:4)in foundation with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M2.5 to 3 including screening shuttering , mixing cement concrete in mixer and placing in position ,vibratig, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Earth work in back filling the trenchage after laying different type and size of pipes with earth removed during excavation within initials leads and lift as per specification and direction of E/I

Providing 12 mm thick cement plaster (1:3) with clean coarse sand of F.M 1.5 with 1.5 mm thick cement punning over it including screening, curing, with all leads and lifts of water,taxes and royalty all complete as per building specification an direction of E/I.

Providing and supplying Blue MDPE pipes confirming to ISO 4427:1996 manufactured from virgin resin PE 80 food grade compounded raw materials having blue colour only assurance certificate from quality agencies like WRC/CIPET (India) / DVGM / KIWA/SPGN etc for usage in drinking water with quality system. The cost shall include testing of all materials all taxes central, state, Municipal, Inspection charges transportation up to site ,transit insurance, loading, unloading, stacking etc complete as specified and directed.PN16(SDR-9) with ED

Providing and supplying G.I. pipes (Tata and euivalent make) for usage in drinking water with quality system. The cost shall include testing of all materials all taxes central, state, Municipal, Inspection charges transportation up to site ,transit insurance, loading, unloading, stacking etc complete as specified and directed.

Lowering laying and jointing HDPE/MDPE pipes in proper position including all specials by compression fitting / electrofusion and But fusion jointing procedure including hydroulic testing as per relevent IS code complete with all materials for jointing procedures like Electrofusion machine , electric mirror/heater/ But fusion welding machine with hydroulic jack,top loading clamp etc pump and accessories for hyroulic tesing and all labours as directed by E/I.as per IS-7634 part-2

Supplying labours and tools for fixing G.I.Pipes with red lead and yarn of following nominal bore with screwed and socketed joints on wall ,ceiling and floor including supplying and fittings of wall hooks or pipe clamps ,wooden plugs, cutting pipes to size and threading ends if required etc all complete as per specification and direction of E/I.

Supplying and fixing of G.M. ferrule of approved make in existing C.I/D.I main including drilling and taping C.I./D.I main all complete as per specification and direction of E/I.

Providing and fixing of G.M. Fullway valve of approved quality all complete as per specification and direction of E/I.

Providing and fixing of male ended C.I.Body brass spindle valve and seat Bib cock of approved quality with extra socket all complete as per specification and direction of E/I.

Supplying and fixing G.I.fitting of approved make all complete as per specification and direction of E/I.

20 mm dia ELBOW

15 mm dia ELBOW

20mm dia Reducing socket

20mm dia Nipple

15mm dia Nipple

20mm dia Union Socket

15 mm dia Socket

20mm dia socket

Carriage of Materials

Railway Crossing

Manufacturing , providing and supplying spirally welded/ERW/SAW Fabricated M.S. Pipe (Commercial Quality) Including Procurements of plates , Gas Cutting to Required size rolling tack welding assembeling in suitable lenghts to from pipes , welding on automatic welding machine and forming V edge on both ends of pipes including all satatutary duites and taxes such as GST Levied by GOI and GOM in all respect, railway freight, instruction unloading from railway wagon, loading into truck, transport to stores /site, unloading, stacking, etc, complete as per IS-3589 and IS 5504 as applicable as per specifications ( no negative tolerance in thickness is permissible)

450 mm 8 mm thickness

400 mm 8 mm thickness

250 mm 8 mm thickness

200 mm 8 mm thickness

Instalation of Product Pipe by Guided auger boring method including making of entry and exit pits, all related civil works like excavation , shoring/ strutting , etc. shielded excavation through augor boring processes , lowering of pipe segment in the jacking pit , laying and jointing of product pipeline through jacking peocess from the jacking pit and restoration of site after project completion as per the instructions of the Engineer-in-charge all complete except the cost of the pipe. In Stoney Soil .

300 to 400 mm dia stoney soil (for 250 mm dia pipe )

300 to 400 mm dia stoney soil (for 200 mm dia pipe )

Providing and applying graphite of approved prime of frist Inferol 49 W emaline 05/58 Pipe coat or any other equivqlent approved paint to the internal surface of pipe line at site.

First coat

Second coat

Operation & Maintenance for Five years

O/M work with Labour component & Chemical Cost for 1st Year Detailed in SBD of section of 9.10

O/M work with Labour component ,Materials for 2nd Year component & Chemical Cost repairing of pipe line work, pumping ,civil, electrical and Mechanical cost Detailed in SBD of section of 9.10

O/M work with Labour component ,Materials for 3rd Year component & Chemical Cost repairing of pipe line work, pumping ,civil, electrical and Mechanical cost Detailed in SBD of section of 9.10

O/M work with Labour component ,Materials for 4th Year component & Chemical Cost repairing of pipe line work, pumping ,civil, electrical and Mechanical cost Detailed in SBD of section of 9.10

O/M work with Labour component ,Materials for 5th Year component & Chemical Cost repairing of pipe line work, pumping ,civil, electrical and Mechanical cost Detailed in SBD of section of 9.10

Labour Cess @ 1%

RAJGRIHI SINGH CONSTRUCTION PVT LTD