82648 SPECIAL REPAIRS TO 02 OFFICERS MD ACCN KAILASH (BLDG NO T-8/1 and 2) AT 2N DET VELLACHI UNDER AGE(I) NAVY CHENNAI

Amount

SCHEDULE 'A'[ B/R WORKS]

Demolition cement concrete (unreinforced) in ground floors and paving n.exc 15cm thick (below & above ground level) complete all as specified and directed.

M&L for PCC 1:5:10 type, E-2 (using 40mm graded agg) as in mass concrete as in sunken floor complete all as specified and directed.

M&L for PCC 1:2:4 type B-1(using 20mm graded stone aggregate) 40 mm thick as in flooring and finishing surfaces even and smooth (without using extra cement) Complete all as specified and directed by Engineer-in-Charge.

M&L for 25mm thick PCC 1:2:4 type B0 (12.5mm graded stone aggregate) as in screed bed over sub base complete all as specified and directed.

Dismantling of wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises including removing of all the debris to a distance n exc 2 km out side the base at the disposal of the contractor complete all as specified and directed.

M&L for screed bed or bedding layer of cement mortar 1:6, 15 mm thick for laying floor finishes complete all as specified and directed.

M&L for 10mm thick screed plaster on fair faces of brick work/concrete in CM 1:3 to receive tiles as in dado Complete all as specified and directed by Engineer-in-Charge.

S&F Coloured non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match Complete all as specified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles 350 x 250mm x7mm/450 X 350 X 7mm thick as in skirting/dados set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick backing coat on fair faces of brick work/concrete in CM 1:4 to receive tiles as in dado complete all as specified and directed.

S&F Double charged virtrified tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 18 sqm but not exceeding 0.38 sqm, in floors, etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over and including 15mm thick screed bed or bedding layer of cement mortar 1:6 complete all as specified and as directed.

All as per above item No.11 here in before but in skirtings complete all as specified and directed.

M & L for Designer cement concrete tiles 30cm x 30cm x 25mm thick, set, jointed and pointed in neat cement slurry with grey and cement pigment in floors over a screed bed of 20mm thick in cement mortar 1:6 complete all as specified and directed.

M&L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc all as specified and as directed by the Engr-in -charge.

M&L for cement slurry @ 3Kg/Sqm provided over cleaned roof surface complete all as specified and directed.

M&L for 10 mm thick cement screed in cement mortar 1:4 with water proofing compound at the rate of 2% by weight of cement to have a smooth surface for laying of water proofing membrane complete all as specified and directed. Note : WPC will be measured and paid seperately

Supply only integral water proofing compound complete all as specified and directed.

M&L for APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) laid over primed surface including bituminous primer confirming to IS-3384 @ 0.3 Ltr/Sqm and applying one coat of bitumen grade 85/25 @1.20 Kg/Sqm by forced all as specified and directed.

M&L for one coat of Aluminium paint applied @ 100ml/Sqm on top layer of roof treatment complete all as specified and directed.

Taking down chowkat or frame with shutters (without taking off shutters from the frames) not exc 1.5 sqm each complete all as specified and directed.

Taking down Chowkats or frames exceeding 1.5 Sqm but not exceeding 4 Sqm each(without taking off shutters from the frames) complete all as specified and directed.

Taking down shutters of any description exc 1 sqm and n.exc 2 Sqm complete all as specified and directed.

S & F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed.

Supply & Fix Factory Made Solid PVC Moulded Door Shutter with particle board core, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick 3D wood grain Moulded PVC Sheet Polyurethane painted on the front face & 2mm prelam PVC Sheet on back face as per specification complete all as specified and as directed.

S & F Second class hard wood plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F 35mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides including 6mm thick teak wood lipping all as specified.

M&L 35mm thick 2nd class hard wood plain framed panelled shutters (two panels) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces.The size of rail and stile as per IS:1003 (Part1),kiln seasoned and chemically pressure treated, all as specified and directed.

S & F 30 mm thick second class hard made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories.(Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories all as specified and directed.. Net Opening will be measured lor payment purpose.) (A) Area not exceeding 2.00 sqm each.

Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).

Supply and fix Anodised aluminium grill (anodised transparent or dyed to requiredshade according to IS: 1868 with minimum anodic coating of gradeAC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin-charge.

S&F sheet glass ordinary quality 5.5 mm thick, in squares n exc. 0.5 sqm each pane complete all as specified.

S & F 4 mm thick Figured glass, pin headed type and glazing with oil putty in squares not exceeding 0.5 Sq. M in each pane complete all as specified and directed.

S & F in repairs Aluminium alloy wire cloth, 0.45 mm dia of wire and average width of aperture 1.40 mm and fixed with stainless wire staples complete all as specified and directed.

S&F 100mm hinges extruded aluminium alloy with galvanised mild steel pin anodized and fixed type C-21 Complete all as specified and directed by Engineer-in-Charge.

S&F 125 mm butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed.

S&F 150mm size aluminium handle, cast type, anodised.Complete all as specified and directed by Engineer-in-Charge.

S&F 200 mm size aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 125 mm size aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 300mm long Aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded section all as specified.

S&F magic eye15mm dia steel body suitable for 35 to 40 mm th doors with all necessary fittings all as specified and direcetd by Engr-in-Charge

S & F Mild steel Angles, bars, flats etc., as in supports for stiffening of fencing, wall ties, hold fasts, clamps, plain angle cleats for securing purlins and similar small articles confirming to Fe 290 Gde E165 complete all as specified and directed.

M&L Providing PCC Type B1 1:2:4 (20mm graded aggregate) in as in hold fast fixing complete all as specified and directed.

S & F Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. Complete all as specified and directed by Engineer-in-Charge.

S & F couple of 25 mm of Stainless Steel fancy Glossy Matte Series Curtain Bracket Complete all as specified and directed by Engineer-in-Charge.

S&F in repair aluminium anodised tubular rail 20mm dia D type 60cm long between flanges including per pair brackets for each towel rail complete all as specified and directed.

S & F 150 mm door stopper of alumiminium alloy body, with rubber bush complete all as specified and directed.

S&F 300mm mild steel ordinary rat tail rod pattern springs incl roller and roller plates complete all as specified and directed.

S & F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding , low level flushing cistern and Flush pipe of 32mm dia but including seat cover) complete all as specified and directed.

S&F in repairs PVC valve less flushing cistern low level 10 litres capacity with syphonic action type with inlet ball valves, float and handle and connections to pipes and fixing of chain and pull (or) lever including brackets and 32mm dia PVC flush pipe of 60cm long complete all as specified.

S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect complete all as specified and directed.

S&F in repair vitreous china, wash hand basin white flat back size 550 x 400 mm white complete waste, chain and pug and precelain stopper including bracket complete all as specified and directed.

S & F 32 mm bore brass chromium plated bottle traps for wash basins with inlet and outlet screwed for pipes or connections including necessary packing union and cap complete all as specified and directed.

Supply & fixing fancy type pillar tap 15mm dia, cast copper alloy with capstan heads, chromium plated screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shank and fly nut screwed for iron pipe & fixed in repairs complete all as specified and directed.

S&F for 32 mm bore High density polythylene pipes (HDPE) of pressure rating 6Kgf/cm2 fixed compete to in walls, floors,ceilings etc complete all as specified and directed.

S&F in repair bib taps concealed type with long shank and cup of fancy type,chromium plated screwed down high pressure with crutch or butterfly handle screwed for iron pipes of 15mm bore complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

S & F PVC (SWR) multiple Floor trap of 75 mm outlet plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair Angle valves fancy type,chromium plated cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15mm bore complete all as specified and directed.

Supply and fixing Brass CP mixer of 20mm dia for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed.

S&F in repair Brass chromium plated shower rose 125mm size, with or without swivel joints, including fixing to steel pipe or union complete all as specified and directed.

S&F in repairs sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S&F soap dish, vitreous China white, approximate size 160x 160x90mm complete all as specified and directed.

S&F kitchen plate rack made of stainless steel 1mm thick including bedding in cement mortar on to wall or including fixing cantilever brackets size 910 x 790 x 255 mm Complete all as specified and directed by Engineer-in-Charge.

Taking down cement plaster on brick walls including racking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

M & L Rendering for 10mm thick in cement mortar (1:6) on other than fair faces of internal bricks or concrete surfaces finished even and smooth without using extra cement all as specified and s directed.

M&L for rendering 15 mm thick in two layers 10 mm thick backing coat in cm 1:6 and 5mm thick finishing coat in cm 1:4 . mixed with water proofing @ 2% by weight of cement with fair & even plasters finshes complete all as specified and directed. (Note :- WPC will be measured separately).

M & L Rendering 5mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:3 with WPC including finished even and smooth without using extra cement complete all as specified and directed.. (Note : Water proofing compound will be measured and paid separately)

M&L for preparing newly plastered surfaces by vacuum based sanding machine and applying two coats of distemper oil emulsion over coat of primer on surfaces of walls including 3mm th wall care putty on walls using mechanical tool/auto roller by smart paint application method complete all as per manufacturer instruction complete all as specified and directed. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate

Material and Labour prepartion of new plastered surface by vacuum based sanding machine and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using mechanical tool/auto roller by smart paint application method complete all as per manufacturer instruction complete all as specified and directed. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate

M & L Preparing newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

Material & Labour complete removal & prepartion of existing treatment by vacuum based sanding machine and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) using mechanical tool/auto roller by smart paint application method complete all as per manufacturer instruction complete all as specified and directed. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate

M & L complete removal of existing treatment & preparation on walls by vacuum based sanding machine and applying two coat of distemper oil emulsion over a coat of primer on surfaces of walls including 3mm th wall care putty on walls using mechanical tool/auto roller by smart paint application method complete all as per manufacturer instruction complete all as specified and directed. Note: All work shall be carried out by approved applicator of paint manufacturer only. The same shall be approved before carrying out the work from AGE(I). Contractor should submit Auth applicator certificate

M & L Preparing old plastered surfaces of celings and applying one coat of white wash complete all as specified and directed.

M & L Preparing old plastered surfaces of walls and applying one coat of white wash complete all as specified and directed.

M & L Preparation of new or previously untreated wooden surfaces of any description, exceeding 10 cm width or girth, not otherwise described and applying two coats of Synthetic Enamel paint over a coat of pink primer complete all as specified and directed.

Taking up or down steel tubing 20mm dia bore and connection complete all as specified

Taking up or down steel tubing 25mm dia bore and connection complete all as specified

Taking up or down steel tubing 40mm dia bore and connection complete all as specified

M&L for Cutting chases, pinning in , for concealed water tubing on brick or stone walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth complete all as specified and directed.

Supplying and laying of CPVC pipes of outer dia 20mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes of outer dia 25mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes of outer dia 40mm dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and fixing CPVC Brass Elbow (3/4 x 1/2) as in special fittings complete all as specified and directed.

Supplying and fixing CPVC Brass Tee of 20mm dia as in special fittings complete all as specified and directed.

Supplying and fixing CPVC 40mm dia Male Brass Threaded Adaptor (MTA/ MBTA) ) as in special fittings complete all as specified and directed.

Supplying and fixing CPVC 40mm dia UNION as in special fittings complete all as specified and directed.

Supplying and fixing CPVC 25mm dia UNION as in special fittings complete all as specified and directed.

S & F in repairs Gun metal 40 mm dia of pipe globe or gate valve with Iron wheel head, screwed both end for Iron pipe one fixed complete all as specified and directed.

Taking down rain water pipe and sewage pipe of any size of pattern including all fittings, heads, shoes, bends etc. complete all as specified and directed.

S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F for 75mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors complete all as specified and directed.

S&F for 110mm dia bore PVC (SWR) pipes single socketed in any length with rubber ring jointslaid in trenches or floors complete all as specified and directed.

S&F for 75mm dia bore PVC (SWR) branch piece, single (Single 'Y') equal or unequal with access door complete all as specified and directed.

S&F for 110mm dia bore PVC (SWR) junction single, (Single 'T') equal or unequal with access door complete all as specified and directed.

S&F for 75mm dia bore PVC (SWR) bends any radius complete all as specified and directed.

S&F for 110mm dia bore PVC (SWR) bends any radius complete all as specified and directed.

S&F for 110mm dia bore PVC (SWR) vent cowl complete all as specified and directed.

S&F for 75mm dia bore PVC (SWR) vent cowl complete all as specified and directed.

M&L for Surface Excavation not exceeding 30 Cm deep and averaging 15 Cm deep and getting out in Soft/ Loose soil complete all as specified and as directed.

M&L hardcore of gauge exc 63mm deposited ,spread &levelled in layers n exc 15cm thick,watered and rammed to a true surface complete all as specified and directed.

M & L 75 mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) in sub base of flooring/ hard standing/pavings/plinth protections complete all as specified and directed.

M&L treating the soil under plinth protection at the rate of 5.0 ltr of emulsion per sqm of surface area complete all as specified and directed.

M&L treating the soil along with external perimeter of building at the rate of 2.25. ltr of emulsion per mtr of the perimeter walls complete all as specified and directed.

M & L Providing ATT by injecting at point of contact of wood work by chemical emulsion (oil or kerosene based solution)@ 0.5 lit/ hole by driling 6mm dia hols at downward angle of 45 degrees at 150 mm centre to centte and sealing the same all as specifiled .

M & L Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm part including drilling and plugging 12mm dia holes with cement mortar 1:2 to match the existing floors complete all as specified and directed.

Demolition of stone slabs and tiles of any description or any thickness in floors, skirtings, risers etc laid ,bedded and pointed in any mortar complete all as specified and directed.

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window- cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over rendering 15 mm thick in CM 1:6 complete all as specified.

M & L 20mm thick Granite (of any type) work (table rubbed and polished) in Skirting for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Providing edge moulding/ Full nosing to 18-20mm thick Granite stone of counters vanities etc. including machine polishing to edge to give high gloss finish etc. complete all as specified and directed.

S & F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S & F in repairs Ball brass valves of 25mm dia, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed in repairs complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided Complete all as specified and directed by Engineer-in-Charge.

S & F Steel rolling shutters of 1.00 mm thickness laths without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer erected in position as indicated complete push & pull or manual type Complete all as specified and directed by Engineer-in-Charge.

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

M&L for brick work with fly ash modular bricks, straight or curved on plan exc. 6m mean radius built in CM 1:6 complete all as specified and directed.

M & L for half brick Brick work with flyash bricks , straight or curved on plan to any radius in built in cement mortar 1:6 complete all as specified and directed.

Demolition of Reinforced cement concrete (Reinforcement cut as required ) of any description and in any position not otherwise specifically provided including padding concrete on roof all as specified and directed.

M & L of TMT barsfor 4 Mild steel bars 10mm dia and over, cut to length, bent to shape equired, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item no 121 , but 6mm to 8mm dia complete all as specified and directed.

M & L for Formwork to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M & L for reinforced cement concrete Type B1 1:2:4 20mm graded aggregate as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L 2nd class hard wood plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with screws exc 13 sqcm but n exc 25 sqcm complete all as specified and directed.

Supply and fix for 18/19 mm thick marine plywood fixed with nails/ screws to frame works as in cabinets cupboards with SS angles cleats etc complete all as specified and as directed.

Supply and Fix for 6mm thick marine plywood fixed with nails/Screws to frame works as in cabinets cupboards with SS angles cleats etc complete all as specified and as directed

Supply and fix for white laminates of 0.9mm thick surface finish matte or glossy colour and pattern as approved adhesive complete all as specified and directed .

Supply and fix for decorative coloured laminates of 1.5mm thick glossy finish, colour and pattern as approved adhesive complete all as specified and directed

Supply and fix for CP decorative type Brass handles, cast type, polished bright handles 75 mm long fixed to plywood or frame complete all as specified and directed

Supply and fix for telescopic channel of size 450mm to 560mm of load per 45 kg/cmsq as complete all as specified and directed.

Supply and fix for 80mm Auto SS hinges of crank 0 degree to 90degree, fixed with screws to plywood or frame work as approved by EIC complete all as specified and directed

S&F for stainless steel accessories grade 202 as mentioned below complete all as specified and as directed. (make:- V-Boss/ Olive -silver accessories or as mentioned in list of make as approved by AGE(I))

(a) Cutlery basket of size 19''x20''x4''

(b) Cup and saucer basket of size 19''x20''x6''

(c) Plain basket of size 19''x20''x8''

S&F in repair Ocean 304 Stainless Steel Bathroom Cabinet with Mirror Door/Bathroom Accessories/Kitchen Storage/Medicine Box (16 X 24 INCH) Complete all as specified and directed by Engineer-in-Charge.

S & F Stainless Steel Double Layer Shelf with Towel Road,Multipurpose Wall Mount Bath Shelf Organizer,Kitchen Shelf/Bathroom Shelf and Rack/Bathroom Accessorie complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided complete all as specified and directed.

S & F Fe-410 W Gde E-250 Quality A Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S & F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.47mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified.

M&L for Cutting grooves in brick/concrete wall, 75mm wide and 65mm deep and shaping horizontal face of grooves with cement mortar 1:3 complete all as specified and as directed.

M&L PCC 1:3:6 type C1 (using 20 mm graded agg) as in padding concrete to maintain required slope including coving to junctions of parapet and roofs complete all as specified and directed.

Removing of debries any description obtained from demolition beyond the lead included in the rates including loading unloading to a distance exceeding 1.5Km and not exceeding 2.00 KM out side defence land complete all as specified and directed.

S&F of Rotational moulded polyethylene 1000 Litrs water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed.

SCHEDULE 'A'[ E/M WORKS]

Taking down copper/aluminium point wiring (light,fan, socket or power) including fixture and fittings complete etc removing the materials for taking credit and making good the disturbed surface of wall/floor etc.

Taking down old/existing MCB DB SPN/ TPN with MCB's complete by disconnecting all as specified and directed.

Taking down old sub main wiring with 2runs/4runs of 4/6/10 sqmm aluminium/copper cablesincluding making good disturbed surface all as specified and directed.

M & L for point wiring (concealed) on walls and surface on ceiling complete with FRLS PVC insulated unsheathed 1100 Volts grade, conforming to IS-694, 1.5 sq mm (nominal area) multi stranded copper conductor cable drawn though in and including non metallic medium grade rigid PVC conduit heavy grade accessories, ISI marked, 19/20 mm dia including all accessories, concealed in walls by cutting chases using machine and making good the disturbed surface, with and including suitable 1.5 sq mm copper earth continuity wire connected to earth dolly complete for the following complete all as specified and as directed.

One light point controlled by one switch

One Ceiling fan/Exhaust fan point controlled by one regulator / switch.

One 3 pin socket outlet 5 amps socket on independent board

One 3 pin socket outlet 5 amps socket on same board

One bell/buzzer point controlled by one push button

One light point controlled by two Nos of two way switches.

All as per above item No. 148 here in before but 3 pin socket outlet 15 amps sockets on independent board with 4sqmm mutistranded copper PVC insulated cable.

S & F switch modular 06 amps one way flush type 1 module complete all as specified and as directed.

S & F switch modular 06 amps Two way flush type 1 module complete all as specified and as directed.

S & F switch modular 06 amps bell push flush type 1 module complete all as specified and as directed.

S & F switch modular 16 amps one way flush type with neon indicator 1 module complete all as specified and as directed.

S & F socket modular 2/3 pin 6 amps flush type 2 module complete all as specified and as directed.

S & F socket modular 2/3 pin 16 amps flush type 2 module complete all as specified and as directed.

S & F only electronic modular fan regulator 120w step type 2 modular complete all as specified and as directed.

S & F modular white cover plate with frame 1 module complete all as specified and as directed.

S & F modular white cover plate with frame 2 module complete all as specified and as directed.

S & F modular white cover plate with frame 3 module complete all as specified and as directed.

S & F modular white cover plate with frame 4 module complete all as specified and as directed.

S & F modular white cover plate with frame 6 module complete all as specified and as directed.

S & F modular white cover plate with frame 8 module complete all as specified and as directed.

S&F Modular Metal flush box 1/2 Module complete all as specified and as directed.

S&F of Modular Metal flush box 3 Module complete all as specified and as directed.

S&F of Modular Metal flush box 4 Module complete all as specified and as directed.

S&F of Modular Metal flush box 6/8 Module complete all as specified and as directed.

M & L for sub main wiring (concealed) complete with two single core 4 Sqmm FRLS PVC insulated unsheathed stranded copper conductor cable drawn through in and including 20 mm dia rigid non-metallic PVC conduit heavy grade and conduit accessories including 4 Sqmm FRLS PVC insulated unsheated stranded copper earth cable connected to common earth dolly complete and including cutting chasing in walls for concealed wiring using machine cutting and making good the disturbed surface all as specified and directed. Make of cable : Polycab, Finolex,Havells Note: 3 run of 4 sqmm & one run of PVC conduit shall be measured as single unit

S & F ceiling rose 3 terminals PVC / Polycarbonate, isolated body complete all as specified and as directed.

S & F Bell, AC,230 Volts, single pole , Multi music type complete all as specified and as directed.

Supply and fixing of single pole and neutral encloser with a two pin and earth plug and socket complete with one single pole MCB 240V, 20Amp complete all as specified and as directed.

Material and labour for telehpone sockets special type complete all as specified and as directed.

Material and labour for TV sockets special Modular fiush type complete all as specified and as directed.

Material and labour for PVC conduit 20 mm dia (For TV and data cable) complete all as specified and as directed.

Material and labour for Junction box(1 to 4 way) for TV/Tele wiring complete all as specified and as directed.

S&F Double Door Vertical TPN Distribution Box 4 way complete in SS enclosure with 200 amps rated busbar.Make : Standard /Lagrant/Havells/L&T or equalent complete all as specified and as directed.

S&F MCCB 415 Volts, 16 KA breaking capacity, 63 Amp, 4 pole. Complete all as specified and directed by Engineer in Charge.

Supply and fixing amp rating 240V, 10KA 'B' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and as directed.

(a) S&F MCB SP 6 - 40 Amps with 10KA breaking capacity

S&F LED light fitting 4feet,1x20w,a trendy wall mounted battern,with extrunded aluminium housing,with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make:- Crompton ,Cat Part NoLTTB4F20WLED/W or equivalent as mentioned in list of make as approved by AGE(I)

S&F LED light fitting 2 feet,1x10w,230v,a trendy wall mounted battern,with extrunded aluminium housing,with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed. Make Crompton Cat Part N0:TTB2F10WLED/W or equivalent as mentioned in list of make as approved by AGE(I)

Supply and fix LED light fitting bulk head 9 W/10W or nearest higher wattage,230v,suitable for Surface, Wall & Conduit mounting,with extrunded aluminium housing,with integrated LED driver, etc. complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed.

S&F Angle type lamp holder ,PVC /Policarbonate type With LED bulb 9 Watt all as specified and Diirected by Engineer in Charge

Supply and fix exhaust fan, made of sturdy Engineering plastic body complete with louvers shutter, voltage AC single Phase. 230V, 50 Hz of size 230/250mm sweep with,RPM 1200, copper winding, completeincluding wiring up to ceiling rose all as specified and as directed by Engr-in-Charge

Supply and fix exhaust fan, made of sturdy Engineering plastic body complete with louvers shutter, voltage AC single Phase. 230V, 50 Hz of size 300m sweep with,RPM 1200, copper winding, complete all as specified and as directed by Engr-in-ChargeNote old unsv exhaust fan will be deposited in MES store yard complete all as specified and as directed.

S & F 25 litre storage water heater 5 star rating , rated power consumption 2000W, current leakage protection device, multi functional safety valve, high precision thermostat control, preset thermal output, high working pressure 0.8MPa ideal for high rise building, vertical mounting, Power consumption not more than 2000watts, Operating voltage 230 volts including all fittings complete & provision of flexible three core PVC insulated multi-stranded copper conductor cable, complete all as specified and as directed. Make:- model Number Puro Turbo 25L (Havells), GHWAPTTIV025 or equivalent as mentioned in list of make as approved by AGE(I)

M&L for Cutting the existing wall for fitting color for exhaust fan and making good disturbed surfaces inner and outer of wall Complete all as specified and as directed by Engr-in-charge

M/L for providing earthing complete with galvanized steel earth plate size 600 mm x 600 mm x6mm thick buried directly in ground earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below normal ground level ,Alternate layers of charcoal) & common salt Crystal and connected to GI earth strip 25x4mm by means of bolts, nuts, check nuts & washers of copper and connecting to earth dolly all as shown in electrical plate No. 3of SSR Part I of 2020 & testing complete including 40mm dia light grade GI pipe upto 7.5mtr long, excavation in any type of strata, PCC ( 1:3:6 ) type C1 earthing chamber, pre cast slab 50 mm thick in cement concrete ( 1: 2 : 4 ) type B 1 ( reinforced with welded steel wire fabric (XPM) weight not less than 4 Kg / Sqm with frame, test box , including 20 mm bore water pipe medium grade GI Tubing including GI Funnel , wire mesh etc. ( NOTE :- Earth continuity conductor and GI protection pipe beyond 7.5m shall be measured and paid under the respective items ).all as directed by Engineer- in charge.

M/L for earth continuity conductor or galvanized steel strip 25x4 mm buried in ground / fixed on wall / drawn in 40mm dia light grade GI pipe, all as directed and specified by Engr in Charge.

Supply laying & testing cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (Heavy duty) with stranded aluminum conductor, 1100 volts grade, of size 4 core 16 Sqmm complete all as specified and as directed.

Supply and fixing Metal Box size 200 X140 X95 mm internal size with hinged door(L) with 1 No PVC connector 4 way 16 Amps and 1 Nos MCB SP 6 Amps including fixing bracket,Nut,Bolts etc complete all as specified and as directed. Make : Sintex Cat part No GSJB2014 or equivalent as mentioned in list of make as approved by AGE(I)

Supply and fixing DWC High density poythelyne (HDPE) pipes of pressure rating 6kgf/ sq/ m of size 40 mm for cable protection laid in trenches complete all as specified and directed

Supply and Laid in trenches/wall GI pipe Light grade 40mm dia as for Road Crossing of Cable/PTL fittings Complete all as specified and directed by Engr-in-harge.

S&F Garden Light Cone series acts as an imposing street furniture. The elegant yet minimalistic design acts a silent observer, IP 65 and giving light, diffuser at the upper portion adds functional value into landscape environment. Make Havells, Model No.BAMBOOBLS8WLED830PSYMTOPC or equivalent as mentioned in list of make as approved by AGE(I)

Supply and fixing post top lantern LED type 40 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete all as specified and directed

Demolition of cement concrete (unreinforced)for passing pipe of any description and in any position not otherwise specially provided for compelete all as specified and as directed

M&L for Pre-cast cement concrete block masonry with solid blocks, exc. 10 cm in width and setting in mortar, complete Type B1 1:2:4 of Using 20mm aggregate complete all as specified and as directed

Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801, PP-R pipes SDR 7.4 (PN-16) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 50 mm ,including fittings complete all as specified and as directed

Supply and lay 3 layer ( inner antimicrobial, outer UV stabilized) ISI marked,IS-15801, PP-R pipes SDR 7.4 (PN-16) and PP-R plain fittings in trenches/walls/cellings or laying in floors complete of size outer dia 25 mm ,including fittings complete all as specified and as directed

Supply and fix PPR Gate Valves (Brass Insert) of 50 mm bore complete all as specified and as directed

Supply and fix PPR Gate Valves (Brass Insert) of 25 mm bore complete all as specified and as directed

Excavation in trenches in Soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5M in depth for laying of cables/pole and getting out of excavated material complete all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick each, excavated soil in trenches after the pipes have been laid and tested complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50 meter and depositing where directed at a level not exceeding 1.50 meter above the starting point complete all as specified and directed.

Banyan Engineers and Contractors (BID ID -3266840)

S Dilli (BID ID -3267220)