8837 REPAIRS / REPLACEMENT AND CLEANING OF SEWAGE LINE, MANHOLES, SEPTIC TANKS AND MISC WORKS LIKE HARD STANDING, FENCING, DRAINS ETC AT VBV, MAP PH-I, DCA, 4/5 GR(FF) AND DAD UNDER AGE BR I SOUTH PUNE

Amount

Scooping & taking out sludge, sullage and foreign materials from septic tank, soak wells of any description and depth including removing and refixing of accessories and appliances required for safe disposal of sludge, sullage and foreign materials either by carrying the same in covered van/trolley outside defence land and it should be disposed off at such place which is not determinated to public health complete all as specified and as directed. (Note :- Depth shall be measured for payment after bailing out water and the rate quoted inclusive of cost required for bailing out water.)

Demolition and breaking up RCC, SWG drain pipes set in cement mortar for the following sizes and removing debris from the site complete all as directed by Engr-in-Charge :-

150 mm bore

200 mm bore

250mm bore

300mm bore

Excavation in trenches not exc 1.5m wide and n.exc 1.5m in depth for foundations, manholes etc and getting out in in soft/loose soil complete all as specified and as directed.

All as per item 3 above but exc 1.5m depth and not exc. 3.0mtr in depth complete all as specified and as directed.

M&L for RCC pipes class NP-2 with socketed ends laid and jointed complete with rubber ring joints of 150mm bore complete all as specified and as directed.

All as per item 5.00 above but 200mm dia.

All as per item 5.00 above but 250mm dia.

All as per item 5.00 above but 300mm dia. (Note for Sl. No. 5 to 8 above :- Laying of sewage line in running sewage water & temporary diversion /plugged of existing sewage line & bailing of sewage water is the responsibility of contractor and the rate for the same is seems to be included in the contract)

M&L for PCC 1:4:8 type D2 using 40mm graded agg as in bed to drain pipes including forming cradles for 150mm pipe complete all as specified and as directed.

All as per item 09.00 above but 200mm dia complete all as specified and as directed.

All as per item 9.00 above but 250mm dia complete all as specified and as directed.

All as per item 09.00 above but 300mm dia complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc 25cm in soil complete all as specified and as directed.

Removing the excavated surplus soils exceeding not exc. 50mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed.

S&F in repairs PVC floor trap with steel grating including jointing with solvent cementof 75 mm dia complete all as specified and directed

S&F in repairs PVC gully traps, square 125/110mm size with grating including jointing to waste pipe in cement joint, dia of outlet 100mm complete all as specified and directed.

Cleaning of manholes of any size and of any depth by taking out semi solid/solid sludge complete and removing sludge in covered vehicle out of MOD land complete all as specified and as directed.

Cleaning and rodding the blocked sewage line to any depth till the smooth flow of sewage line is restored including plugging of manholes temporarily as and when required and washing down complete sewage line with water including removing sludge and foreign materials from manholes in line and removing and refixing manhole covers and rodding complete all as directed by Engineer-in-Charge for following bore of pipes :-

150 mm bore

200 mm bore

250 mm bore

300 mm bore

Day to day maintenance and petty repair of sewage line (complaints pretaining to safaiwala) by attending daily complaints lodged by the users through IVRS/mobile/sms or email and manual registratering of complaints at B/R complaint cell on all working days (except Sunday, National Holidays and Closed Holidays) by deploying 03 (Three) Safaiwala per day, complete all as specified and directed by Engr-in-charge. [Note : i) Minor complaint shall be completed within 24 hours and major complaints within a week. ii) If safaiwala not attended complaint within time frame mentioned above 50 % shall be deducted job completed by him. iii) The contractor will be responsible to maintain daily job completed by the safaiwala deputed by him in the sub work and obtained signature of I/C complaint cell/Engr-in-Charge daily at 1700 hours on all working days.]

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required, for the following size of pipe :-

150mm bore

200 mm Bore

250 mm bore

Demolition of cement concrete of any description and in any position not otherwise specifically provided for

Demolition of brick work or stone/boulder masonry, built in cement mortar

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for

M&L for granite 18mm thick (of any type) work (table rubbed and polished) in steps ,pillar, window cill,shelf,cooking platform and like in cement mortar (1:4) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, shelf cooking platform, and other similar situations complete all as specifed and directed.

S&F sink without drainage board made of stainless steel, 1 mm thick for kitchen or laboratory, with plug, waste pipe, washers and wastes, including bedding in cement mortar on to dwarf walls or including fixing cantilever brackets and connecting union to pipe overall size 550 mm X 460 mm with bowl size 410 mm X 330 mm X 160 mm complete all as specified and directed. (Make : Nirali / Bluestar / Diamond).

S & F machine cut cuddappa stone slab one side polished 40 to 50 mm thick as in shelf set and jointed in neat cement slurry and pointed in coloured cement to match, laid over and including 15mm screed bed in cement mortar (1:4) complete all as specifed and directed.

M&L for cast iron floor/Nahani trap with grating 75mm dia including jointing to waste pipe in run lead including removing old traps complete all as specified and as directed.

M&L for providing precast RCC (1:2:4) type B1 using 20 mm graded stone aggregate in manholes covers and slabs set in CM 1:4 complete all as specified and as directed.

M&L for mild steel TMT bars 8 to 10mm dia cut to length, bent to shape required, bending and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 as in foundations, filling in mass concrete etc. complete all as specified and as directed.

M & L for solid block masonary exc. 10 cm width blocks of PCC design mix Gde C-5 set in CM (1:6) complete all as specified & directed by Engr-in-Charge.

M&L PCC (1:2:4) type B-1 using 20 mm stone graded aggregate as in benching, coping etc complete all as specified and as directed.

M&L for brick work with fly ash Bricks straight or curved on plan exec 6 mtr mean radius with moduler bricks in CM 1: 6 complete all as specified and as directed.

M&L for brick work with fly ash bricks straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

M&L for Walling of Random rubble masonry uncourse well bonded bedded and solidly hearted built in cement mortar (1:6) as use in drain etc complete all as specified and as directed.

M&L for Plain cement concrete 1:3:6 type C-2 (using 20 mm graded crushed stone aggregate) as in surface channels and drains (including necessary form work) complete, all as specified and directed.

Extra for forming fair finished drain or channel inner girth n.exc 30 CM in cement, concrete using extra cement including forms, moulds, mitred/stopped ends etc complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

Rendering 15mm thick in cement mortar 1:4 on brick surfaces finished even smooth with sponge finish duly mixed with integral water proofing compound as per manufacturers instrucitons complete all as specified and as directed. (Note :- WPC shall be measured and paid separately)

Rendering 15 mm thick on block walling surface in CM (1:4) finished surfaces even and smooth using extra cement complete all as specified and directed.

Rendering 15 mm thick on block walling surface in CM (1:6) finished surfaces even and smooth using extra cement complete all as specified and directed.

M&L for 5mm thick plastering in CM 1:3 on concrete surfaces of ceiling finished even smooth without using extra cement complete all as specified and directed.

M&L for new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer all as specified and directed.

M&L for new palstered surface of wall and applying two coats of oil bound distember over a coat of primer complete all as specified and as directed.

M&L for new palstered surface of ceiling and applying two coats of white wash complete all as spd and directed by EIC.

S&F in repairs vitreous china wash down water closet pan (squatting pan) white including provn of concrete bedding fixed, "Orissa" pattern size 580x440mm white colour with integral foot rests (excluding flushing system and flush pipe) complete all as specifed and as directed. (Make : Cera / Hindware / Parryware)

S&F in repairs vitreous china wash down water closet pan, 'Pedestal' coloured, including fixing bolts etc including PVC seat cover white with flat bottom including MS, CP or aluminium anodised hinge device etc complete all as specified and directed. (Make : Cera / Hindware / Parryware)

S&F in repair vitrous china wash hand basin pedestal snow white 630x480mm flat back including and providing waste pipe 40mm dia medium grade, CP brass wast coupling 32mm dia with check nut washer etc fixed complete all as diected by EIC. (Make : Cera of cat no S2090109 or equivalent make specified here-in-after

S&F in repair for 10 litres capacity PVC flushing cistern low level including ball valve inlet & outlet connection 15 mm dia PVC pipe with check nuts on both ends, PVC waste pipe 32 mm upto WC connection and GI 15 mm dia overflow pipe upto floor level complete all as specified and as directed. (Make : Commander/Slimline/Cera)

Taking down angle iron/ wooden chowkats or frames with shutters (without taking off shutters from the frame) exc. 1.5 sqm but not exc. 4sqm each and removed to store complete all as specified and as directed.

S&F Pressed steel door frame of frame size 105x60mm with one or more revates incl necessary fixing, hinges, lock strike plate etc filled with PCC 1:3:6 type C-0 complete all as specified and as directed.

S&F pressed steel frame 125x60mm for doors with one or more rebates incl necessary fixing lugs, Hinges lock strike plate filled with PCC 1:3:6 type C-0 etc complete all as specified and as directed.

S&F 30 mm thick Flush shutters, solid core construction, with particle board core and one face is covered with decorative face veneer with lipping/frame to match, supplied and fitted to chowkats complete all as specified and as directed.

S & F 30 mm thick Iind class hard wood glazed and skeleton shutters, devided into squres with plain, chamfered or rounded mitered and rebated sash bars any numbers, open rebated prepared to receive guaze, edges of framing plain, chamfered or rounded , fitted with cut and mitered beads for securing glass etc size of members of shutters in SSR Part- I, Section 8, Clause 8.24 (a) complete all as specified and as directed.

M & L for preparation of new or previously untreated surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer to newly wood surfaces complete all as specified and as directed.

S & F stainless steel wirecloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm & fixed with stainless steel wire stapples complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet, reinforced with M.S square tube, supplying & fixing in opening as per specifications, drawings complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting, of frame made out of M.S tubes for top & bottom rails M.S frame shall be covered with heat molded plain co lour PVC ‘C’ channel having a PVC sheet strip of 20mm width struck inside with solvent cement for steel & plain co lour PVC sheets for top rail, lock rail& bottom rail on either side & or gap insert for top rail & bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stile & rails with suitable PVC sheet banding, and joints to gather with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specifed and as directed.

S & F 100 mm long butt hinges medium weight , cold rolled Mild steel for door shutters complete all as specified and as directed.

S&F 150 mm aluminium anodized barrel tower bolts of extruded section for door shutters complete all as specified and as directed.

S & F 300 mm long aluminium alloy, anodised sliding door bolt with hasp , staple( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast - aluminium alloy and fixed complete all as specified and as directed.

S & F 150 mm extruded aluminium alloy handles, fabricated type anodised complete all as specified and as directed.

Taking down shutters of any description not exc1 sqm each complete all as specified and as directed.

Taking down shutters of any description exc 1 sqm and not exc 2 sqm each complete all as specified and as directed.

S&F in repair three track sliding window with two or more shutter witth 4 mm thick tinted glass , one shutter of stainless steel wire cloth 0.36 mm nominal dia & 1.18 mm width aperture for mosquito proofing with good quality bearing, handle lock, rubber beading and glazing clips etc using following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make complete all as specified directed by Engr-in-Charge. (a) Bottom frame 20620 (b) Top frame & Verrtical 20621 (c) Handle (side) 20606 (d) Shutter inter lock 20724 (e) Shutter top & Bottom 20844 (f) Glazing Clip 19352

S&F ventiltors/ louvers with partially guaged shutter using 5 mm thick x 10 cm wide frosted glass strips and following aluminium powder coated sections conforming to catalogue of 'JINDAL' or of equivalent make and rubber beading etc all as directed. (a) SP 20048 (b) Glazing clips 19352

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for coloured Ceramics tiles 300x200x7to8mm thick in vertical surfaces such as skirting dado set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 15mm thick rendering in cement mortar 1:6 on stone / brick/ concrete masonry surfaces all as specified

M&L for coloured Ceramics tiles 450 x 300 x 7 to 8mm thick in vertical surfaces such as skirting dado set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick rendering in cement mortar 1:4 on stone / brick/ concrete masonry surfaces complete all as specified and as directed.

M&L for Non skid ceramic colored tiles 7 to 8mm thick, (square/ rectangular) area of each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm in floor etc.set and jointed in neat cement slurry & pointed in white or coloured cement to match including 15mm thick screed bed or bedding layer as in CM 1:6 complete all as specified and as directed.

M&L for Non skid ceramic colored tiles 7 to 8mm thick, (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm in floor etc.set and jointed in neat cement slurry & pointed in white or coloured cement to match.including 15mm thick screed bed or bedding layer as in CM 1:6 complete all as specified and as directed.

M&L for Non skid ceramic colored tiles 7 to 8mm thick, (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in skirting , set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10 mm thick backing coat in CM 1:4 all as specified and as directed by Engr-in-Charge.

Supply only integral water proofing compound complete all as specified and as directed.

Demolition and breaking of drain pipes AC /CI/PVC set in cement mortar or adhensive all as directed of 75mm to 110 mm dia complete all as specified and as directed.

S&F in repair PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall or laid in floors/in earth of 110 mm dia complete all as specified and as directed.

All as per Sl. item No. 76.00 above but 75mm dia complete all as specified and as directed.

Refixing of old PVC pipes single socketed in any length with rubber ring joints fixed to walls or laid in floors of 110mm dia complete all as specified and as directed.

Refixing of old PVC pipes single socketed in any length with rubber ring joints fixed to walls or laid in floors of 75mm dia complete all as specified and as directed.

S&F PVC (SWR) bends plain 110 mm bore complete all as specified and as directed.

S&F PVC(SWR) bends plain 75mm bore complete all as specified and as directed.

S&F PVC (SWR) bends with oval access door of 110 mm bore complete all as specified and as directed.

S&F PVC (SWR) bends with oval access door of 75 mm bore complete all as specified and as directed.

S&F PVC SWR Branch piece single (Single Y) equal or unequal 110mm dia with door access complete all as specified and as directed.

S&F PVC SWR Branch piece single (Single Y) equal or unequal 75 mm dia with door access complete all as specified and as directed.

S&F PVC (SWR) of 110mm dia junction single (single 'Tee') equal or unequal with door access complete all as specified and as directed.

S&F PVC (SWR) of 75 mm dia junction single (Single 'Tee') equal or unequal with door access complete all as specified and as directed.

S&F PVC SWR Branch piece double (double 'Y') equal or unequal 110mm dia with door access complete all as specified and as directed.

S&F PVC SWR Branch piece double (double 'Y') equal or unequal 75mm dia with door access complete all as specified and as directed.

S&F for 110 mm dia PVC SWR vent cowel complete all as specified and as directed.

S&F for 75 mm dia PVC SWR vent cowel complete all as specified and as directed.

S&F in repairs of steel grating of 100mm in size for nahni trap/floor including jointing complete all as specified and as directed.

M&L for PCC 1:2:4 type B-1, (using 20mm graded stone aggregate)as in surface channels and drains incl all moulds and forms all as spd and directed.

Surface excavation n.exc 30cm deep and averaging 15cm deep and getting out all as specified in (Soft/hard) average soil complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base / flooring complete all as specified and as directed.

M&L for precast cement concrete interlocking paver blocks, coloured, glossy finish with any shape and size 60mm thick, M-35 grade, laid over & including 75mm thick PCC ,CM 1:3:6 and 25mm thick stone dust/grit all as specified and as directed.

Surface dressing n.exc 15cm deep including cleaning grass vegetation saplings shrubs , bush wood, ungrowth roots and trees not exc 30cm girth including disposal of spoils , in any type of soil all as directed by Engr-in-Charge.

M & L for Moorum/red bajri filling in floors or pavings, laid in layers not exc. 15 cm thick, spread, levelled and rammed including watering all as specifed and directed.

M&L for 75mm thick PCC (1:3:6) type B2 (using 20mm graded aggregate) as in plinth protection/hard standing, finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed.

S G Engineers

PRASHANT CONSTRUCTION

TULSAYA CONSTRUCTION

M/s Omkar Associates