SPECIAL REPAIR TO MD ACCN QTR NO PR-126 TO PR-129 AND PR-246 TO PR-249 AT SEVOKE ROAD MIL STN UNDER GE SEVOKE ROAD

Dismantling plain or corrugated steel sheeting any thickness, complete all as specified and directed.

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding ( but not backing ) removing serviceable tiles to store and rubbish off the premises etc complete all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc complete all as specified and directed

Demolition of concrete (reinforced) of any description Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work, removing rubbish off the premises etc complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, complete all as specified and directed.

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 sqmtr but not exceeding 4 sq m each, and refixing the shutter with new frame in the same opening complete all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed

Demolition of brickwork built in cement mortar and removing rubbish off the premises etc complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets complete all as specified and directed.

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retrieved debris as directed including necessary scaffoldings etc complete all as specified and directed

Taking up or down 15 mm bore steel water tubing and connections complete all as specified.

Taking up or down 20 mm bore steel water tubing and connections complete all as specified.

Taking up or down 25 mm bore steel water tubing and connections complete all as specified.

Materials and Labour for plain cement concrete (1:3:6) type C1 (20mm graded crushed stone aggregated) as in holdfast block, filling of MS chowkats and the like including necessary formwork complete all as specified and as directed.

Materials and Labour for formwork to chullah hoods, chajjas, cooking or other platform, troughs and similar items including edges Complete all as specified and as directed.

Materials and Labour for reinforced cement concrete (1:1.5:3) type A1 (nominal mix) using 20 mm graded stone aggregate as in chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces etc, any thickness, placed in position complete all as specified and directed. (Note: Steel reinforcement shall be measured & paid separately)

Materials and Labour for TMT bars 6 to 8 mm dia , as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

Materials and Labour for rolled mild steel roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc.conforming to Fe 410-W (Gde-E- 250) quality-A including painted one shop coat of zinc chromate primer paint (including preparation of surface) at workshop before fabrication complete all as specified and as directed.

Supply & fixing mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Supply & fixing wire netting of galvanised steel wire 1.40mm dia, size of mesh 12 mm, fixed with tinned tacks of wire staples complete all as specified.

Supply and fixing Pre-painted galvalume aluminum zinc coating (AZ-150) GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Supply & fixing 0.71mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joint) complete all as specified and as directed.

Materials and labour for preparing of new wooden surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

Materials and labour for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

Materials and labour for preparing of old painted steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Materials and labour for preparing of old painted wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Materials and labour for re-writing letters or figures (Block, Roman, Italic or Indian) n.exc 30cm height with synthetic enamel paint complete as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15 mm thick screed bed or bedding layer of cement mortar (1:6) for laying of floor finishes complete all as specified and directed.

Materials and labour for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm,on vertical surfaces such as skirting,dado and risers to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 10mm thick screed bed or bedding layer of cement mortar (1:4) complete all as specified and directed.

Materials and labour for coloured 450x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

Materials and labour for chequered cement concrete tiles 30cm x 30 cm size, 25 mm thick (with grey cement and pigments), set, jointed and pointed in neat cement slurry in floor with grey cement mixed with pigments to match with the colour of tiles, laid over and including 20 mm thick screed bed in CM 1:4, complete all as specified and directed.

Materials and labour for 20mm thick granite slabs of any type (table rubbed and polished) on cooking platforms, slabs and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed.

Materials and labour for Kota stone slab 20-25mm thick in riser of steps,skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:3) including rubbing and polishing complete.

Materials and labour for Kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement mortar (1:6)and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete.

Materials and labour for 75 mm thick plain cement concrete (1:3:6) type C2 using 40 mm graded stone aggregate as in path, plinth protection etc. finished the surface of concrete even and smooth without using extra cement including provn of 10 mm joints (at an interval of 3 m and corners) duly filled with fine sand and bitumen in a ratio 3:1, complete all as specified and directed.

Materials and labour for 25 mm thick PCC (1:2:4) type B0 using 12.5 mm graded stone aggt as in floors finished even and smooth with using extra cement, complete all as specified and directed.

Materials and labour for 25 mm thick PCC (1:2:4) type B1 using 20 mm graded stone aggt as in sub bases of floor finished even and rough, complete all as specified and directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

Materials and labour for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:6 complete all as specified and as directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing, complete all as specified and directed.

Supply and fixing Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

Supply and fixing second class hard wood plain solid straight chowkhats and frame wrought framed rebated on the soild, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and directed.

Supply and fixing 105 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hings lock strike plate etc complete all as specified.

Supply and fixing 125 x 60 mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified.

Supply and fixing flush door shutters 30mm thick solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing 35mm thick second class hard wood glazed and skeleton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, complete all as specified and directed.

Materials and labour for 18/19mm thick prelaminated particle board, exterior grade, first quality, prelaminated one side with decorative choice lamination & other side balancing white lamination , fixed with screws to timber frame work as in cabinet, cup board,moduler kitchen etc. including external teak wood lipping all round, 6mm thick fixed with nails complete all as specified.

Extra over rates of 18/19mm thick plywood/particle board for external teak wood lipping, 6mm thick fixed with nails complete all as specified.

Materials and labour for first class hard wood plain fillets. square, rectangular or triangular in section, wrought, secured with nails or brads of sectional area exc 3 sqcm and not exc 6 sqcm complete all as specified and directed. .

Supply and fixing stainless steel butt hinges, 100 mm size , complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 150 mm long, complete all as specified and directed.

Supply and fixing Aluminium anodized barrel tower bolts of extruded section, 125 mm long, complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 150 mm size , complete all as specified and directed.

Supply and fixing extruded aluminium alloy handles, fabricated type, anodized, 125 mm size , complete all as specified and directed.

Supply and fixing for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

Supply and fixing Hasp and staple, safety type, aluminium anodised 100 mm including bolt to hinge plate and fixed with screws complete as specified and directed.

Supply and fixing in repair continuous (Piano) hinges mild steel bright finish or electro galvanised, width of flaps when open 30mm complete as specified and directed.

Supply and fixing CP curtain rails 20 mm dia chromium plated, with and including fixing brackets, stops, rollers etc, complete al as specified and directed.

Supply & fixing collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars top and bottom runners, brass handles etc as specified erected in position and securing runners with hold fast and brackets complete all as specified and as directed.

Supply and fixing 4 mm thick sheet glass, ordinary quality and glazing with oil putty or with aluminium beading in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing 4 mm thick figured glass, ordinary quality and glazing with oil putty or with in squares n.exceeding 0.50sqm in each pane , complete all as specified and directed.

Supply and fixing in repair Aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed.

Materials and labour for rendering 15mm thick in cement mortar (1:6) on fair faces of brick work or concrete surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 5mm thick in cement mortar (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

Materials and labour for rendering 20mm thick in two layers of 10 mm thick each in cement mortar (1:4) on fair faces of brick work or concrete surfaces,WPC shall be mixed with morter of top layer, finished even and fair, complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only integral Water Proofing Compound of approved make.

Materials and labour for preparation of new/old plastered surfaces of wall and applying 2-3mm thick wall care putty of approved make complete all as specified and directed.

Materials and labour for applying three coats of white wash on new ceiling surface including preparation of surface, complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper of approved colour with roller over one coat of alkali resistant primer after preparation of surface complete all as specified and directed.

Materials and labour for preparation of new plastered surfaces of walls and applying one coat of Primeseal primer of Dr Fixit or equivalent chemical of Fosroc/ STP Ltd as approved by GE or one coat of Chemstic PDE 600 elastomeric coating (allow to dry for 8 hours) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of Dr Fixit with DFT 100 microns or Shalicryl 215 of STP Ltd or Chemstic PDE 600 elastomeric coating as approved by GE (surface shall be allowed to dry for 6-8 hours after one coat before application of next coat) including necessary scaffolding as required at site complete all as specified and directed . Note:- Work shall be executed by the authorised applicator of the manufacturer and contractor to submitt authenticate document on this account.

Materials and labour for preparation old decorated surfaces of ceiling including brooming down or steel wire brushing scraping down smoke shoot, moulds, moss and efflorescent salt sand trading oil and greasy spots and applying two coats of white wash complete all as specified and directed.

Materials and labour for complete removal of existing treatment from walls and applying two or more coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm /litre and UV resistant as per IS 15489:2004 alkali and fungal resistant exterior paint of required shed(company depot tinted) with silicon additives1.43 lits/10 sqm over and including primer coat of exterior primer applied 0.90 litre/10 sqm over a coat of 1mm thick putty over plastered surface to prepare the surface even and smooth complete all as specified and directed .

Materials and labour for complete removal of existing treatment from wall surfaces and applying two coats of oil bound distemper with roller over one coat of primer of approved colour after preparation of surface complete all as specified and directed.

Materials and labour for 605X605mm anodised aluminium snap grid frame work for false ceiling including hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long including supply and fixing 4mm thick Decorative non asbestos fibre cement boards fixed or laid/ inserted to aluminium frame work as in ceiling complete all as specified and directed. Note:- The size of aluminium main and cross tee shall be 40mm x25mm x2mm and size of angle shall be 25mm x 25mm x 2mm or higher)

Supply and fixing 15 mm bore medium grade galvanized steel water tubing with all fittings, concealled to wall/ceiling complete all as specified.

Supply and fixing 20 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing 25 mm bore medium grade galvanized steel water tubing with all fittings, fixed to wall/ceiling or laid in floor complete all as specified.

Supply and fixing in repairs, stainless steel sink with drainage board, 1 mm thick for kitchen or laboratoty with plugs, waste pipe, washers, including cantilever cast iron brackets, connecting union to waste pipe etc including bedding in cement mortar to dwarf wall, overall size 915x460mm with bowl size 410mm x 330mm x160mm with 40 dia mm CP waste coupling and PVC waste pipe complete all as specified and directed.

Supply and fixing in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12cm wide with CP brass bracket guard railing 60cm long complete all as specified and directed.

Supply and fixing in repair kitchen plate rack made out of stainless steel 1mm thick sheet with partition and minimum size of rack 800X250X900 mm with shape and pattern as per sample kept in sample room of GE office complete all as specified and directed.

Supply and fixing in repair Vitreous China wash down water closet pan (pedestal pattern), white with "P" or "S" Trap front or back inlet fixing bolts, PVC seat cover complete and making all necessary connection as specified and directed.

Supply and fixing in repair 10Ltr capacity PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed.

Supply and fixing in repairs Vitreous China wash hand basin, white, flat back, size 550x400mm, including 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed, brackets, with and incl 32mm dia 90cm long PVC waste down pipe, includind S&F cromium plated Pillar taps 15 mm bore, with capstan heads screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks & fly-nuts, screwed for iron pipe complete all as specified and directed.

Supply and fixing for 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

Supply and fixing in repairs, 15mm cromium plated Bib taps, cast copper alloy with crutch or butterfly handle, fancy type, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

Supply and fixing in repair Concealed 15 mm bore angular stop valve cast copper alloy fancy type chromium plated with long shank and cup (concealed type) with capstan head wall flange etc screwed down screwed for iron pipe complete all as specified and directed. .

Supply and fixing in repair 15 mm bore Brass CP basin mixer for mixing hot & cold water fancy type screwed down high pressure with letter hot and cold with long screwed shank and flynuts screwed for iron pipe, complete all as specified and directed.

Supply and fixing in repair 15 mm bore Brass CP sink mixer for mixing hot & cold water fancy type screwed down high pressure with letter hot and cold with long screwed shank and flynuts screwed for iron pipe, complete all as specified and directed.

Supply and fixing in repair 15 mm bore Brass CP wall mixer for mixing hot & cold water fancy type, 3 in 1 system with provn of for head shower with long bend pipe and wall flangs with 125 mm size CP shower rose with swivel joint and matching CP arm, screwed down high pressure with letter hot and cold with long screwed shank and flynuts screwed for iron pipe, complete all as specified and directed.

Supply and fixing Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

Supply and fixing Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and directed.

Supply and fixing in repairs brass chromium plated, shower rose, 125mm size complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints fixed to walls with suitable size clamps, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, complete all as specified and directed.

Supply and fixing PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

Supply and fixing PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

Supply and fixing PVC (SWR) junction single, (Single T) equal or unequal, 75mm bore, complete all as specified and directed.

Supply and fixing PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

Supply & fixing rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) 500 Ltr capacity hoisted and fixed in position, connecting with existing pipes all as specified in SSR Part I complete all as specified and directed.

Supply and fixing ball brass valves of size 25 mm bore high pressure, with polythene float and fly nut, screwed for iron pipe etc complete all as specified and directed.

Supply and fixing 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

Taking out old existing APP membrane or any other roof treatment work, roughening surfaces of existing roof and removing debris from site including cleaning and washing down with water to remove all dust/dirt etc complete all as directed.

Materials and Labour for 25 mm average thickness plain cement concrete (1:2:4) type B-0, using 12. 5 mm graded crushed stone aggregate over roof/ chajjas to achieve required slope including formwork, making rounded chamfered on edges, mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: WPC shall measured and paid separately.

Materials and labour for removing loose , disturbed or disintegrated old concrete surfaces of RCC beam, column, lintel, chajja, facia, railling etc, cleaning thoroughly exposed reinforcement by sand blasting using suitable pump as directed by the GE, preparing exposed concrete surfaces to receive guniting, applying one coat of anti corrosive paint to the exposed reinforcement, supply and fixing welded wire mesh of size 100x100 mm of 3 mm dia wire weight not less than 1.37 kg/sqm & binding with 22 guage mild steel (annealed) binding wire to reinforcement and applying pressure guinting in cement mortar 1:3 minimum thickness 30mm and thereafter rendering 10mm thick plaster in cement mortar 1:3 mixed with water proofing compound @ 3% by weight of cement and finishing the surfaces even and smooth without using extra cement to match with the existing surfaces removing the debris from site of work, including material and labour for necessary scaffolding and safety arrangement for guinting work, complete all as specified and as directed. (Note :- The finish of the surfaces to be matched with the existing surface. WPC shall be measured & paid separately as supply only)

Materials and labour for brushing neat cement slurry with 3.0 kg of cement per sq metre all as specified and as directed.

Materials and labour for 10 mm thick rendering in cement mortar (1:4) over RCC roof surface to receive roof treatment finished even and smooth without using extra cement mixed with water proofing compound as per manufacturers instruction (WPC shall be measured and paid separately).

Materials and labour for providing, laying water proofing treatment over plastered surfaces of RCC roof with following steps of work to be carried out through authorised person/applicator of manufacturer :- (a) The dried plastered surface of slab shall be painted with one coat of bituminous primer @0.4 liter/Sqm. (b) Over the primed surface a layer of APP based polymeric membrane minimum weight of 3 kg/sqm of approved manufacturer minimum 3mm thick, reinforced with polyster non woven fabric (weighing not less than 150gms/sqm) shall be laid by torch application method. The side over laps of membrane shall be minimum75mm and the end laps shall be minimum 100mm and sealing all overlaps and joints shall be done as per manufacturer's instruction. Make of APP:-M/S TEXSA INDIA LTD (MOPLY-FP) / M/S STP LIMITED (SUPER THERMOLAY) / IWL INDIA LIMITED (HYPERPLAS)/M/S Tiki Tar Danosa (India) Pvt Ltd (Hydro Stop)

Removing of old unserviceable building materials /debris etc. to a distance of 100m or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination, complete all as specified and directed.

Add over item No. 117 for every additional 100 metres or part thereof (upto 1.0 km total distance)

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

All as per Item No.120 above but for One 2/3 pin socket outlet 5/6Amps on independent board

All as per Item No.120 above but for One light point controlled by two nos two way switches.

All as per Item No.120 above but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

All as per Item No.120 above but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Supply and fixing Switch piano, flush type, single pole, one way switch 5 Amps.

Supply and fixing Switch piano, flush type, single pole, two way switch 5 Amps.

Supply and fixing Switch socket combination 2 in 1, 5 Amps flush type.

Supply and fixing Switch socket combination multipurpose 5 A/16 Amps,5 in 1, flush type.

Supply and fixing Ceiling rose surface bakelite 3 terminals 65x50mm all as directed.

Supply and fixing Socket outlet 3 Pin, 5 Amp flush type universal, 240 volts, complete all as specified all as directed.

Supply and fixing Bell Push Flush type 5 Amp, 240 volt all as specified.

Supply and fixing Bell Ding-Dong AC 230 V Single Pole complete all as specified and as directed.

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and as directed.

Supply, fixing and connecting exhaust fan steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers complete all as specified and as directed.

Supply, fixing and connecting exhaust fan made of polycarbonate/sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 150mm complete all as specified and as directed.

Supply and fixing in repair energy saving and environmental friendly long life LED security/street Light fittings 35 watts, made up of pressure die cast aluminium housing with high efficiency LED as lighting source and lens embedded PC cover, IP 66 protection, inbuilt driver, connecting with suitable size copper wire, with 25mm bore 1.5 m long medium grade GI bracket made to shape complete all as specified and as directed.

Taking down existing unserviceable light fitting and Supply and fixing new decorative type surface and wall mounted 20 Watt LED batten light fittings, 4 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Taking down existing unserviceable light fitting and Supply and fixing new decorative type surface and wall mounted 9/10 Watt LED batten light fittings, 2 feet long, with aluminium housing and integrated electronic driver, fixed to walls/ceiling, environmental friendly, energy efficient ready to use pack .

Supply and fixing in repair MCB distrubution board TPN 4way, double door, IP 43, IK-09, sheet steel, phosphatised,powder coated with 200 amps rated bus-bar,neutral link,earth bar and din rail, 415 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing in repair MCB distrubution board SPN 8 way, double door, IP 43, IK-09, sheet steel, phosphatised, powder coated with 200 amps rated bus-bar,neutral link, earth bar and din rail, 240 V, including taking down existing unserviceable DB with MCBs complete all as specified and directed. by Engineer-in-charge.

Supply and fixing MCB Tripple pole and neutral (TPN), 415 volts 63 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB Single pole and neutral (SPN), 240 volts 32 Amps 10 KA rupturing capacity, C series

Supply and fixing MCB Single pole (SP), 240 volts 5 to 32 Amps 10 KA rupturing capacity, C series

Materials &Labour for submain wiring with two single core PVC insulated, unsheathed, stranded copper conductor of size 6.0 Sqmm and one single core PVC insulated, unsheathed stranded copper conductor 6.0 Sqmm green in colour as earth continuity conductor drawn into and including PVC casing capping (medium grade) of suitable size with all fitting & accessories complete including taking down old unserviceable sub-main wiring all as specified and directed by Eng-in-Charge . (Note: Two runs of 6 Sqmm cable and one run of 6 Sqmm earthing cable along with casing capping altogether shall be measured as one unit.)

Supply and fixing electric water heater (Geyser),storage type, steel body, with copper inner tank and heating element upto 2 KW, 25 lits capacity, BEE 5 star rating, complete all as specified and directed.

Supply and fixing to walls 40 mm bore medium grade galvanized steel tubing of length 3 to 3.2m for hanging ceiling fans including suitable size hooks made to shape complete all as specified and directed.

Materials and labour for earthing complete with galvanized steel pipe electrode 40mm bore , medium grade, 2.5 meters length, buried directly and preferably vertically in ground with top edge not less than 1.25 meters below ground level connected with earthing lead galvanized iron strip of size 25x4 mm connected to galvanized earth pipe by means of bolts, nuts, checknuts and washer of galvanized iron including PCC (1:2:4) type B1 precast RCC cover slab with suitable handle made of 6mm round bar, including necessary excavation and earth work in any type of soil, 20mm dia medium grade galvanized steel tube for watering with one end fix with cast iron funnel and wire-mesh , with protection pipe of 32 mm dia light grade galvanized steel tubing upto 7.5 meters length for drawing earthlead including common salt, charcol , bentonite in alternate layers etc, complete all as shown in EP number 2 of SSR part-1 including testing on completion and including taking down old u/s earthing & testing complete all as specified and as directed.

Please Enable Macros to View BoQ information