SPL REPAIR TO BLDG NO T-44, T-45, T-46, T-47, T-27, T-28 AND T-83 IN JAISALMER MIL STN UNDER GE (A) JAISALMER

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/ disintegrated rock all as specified & directed by Engineer-in-Charge.

Removing excavated soft/ disintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by the Engineer-in-Charge.

Demolition of cement concrete (un reinforced) in ground floors and pavings n.exc 15 cm thick (below or above ground level) & removing rubbish out side MD land complete all as specified and directed by the Engineer-in-Charge.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 including with demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc complete all as specified and directed by the Engineer-in-Charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exc 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses complete all as specified & directed by Engineer-in-charge.

S&F Pre-painted galvalume aluminium zine coating GI based corrugated steel sheeting 0.50mm thick any colour having tensile strenght 550Mpa in roof coverings fixed with self tapping screws including dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified & directed by Engineer-in-charge. Note :- (i) The fixing of Galvalume roof sheet as in sun-shades & in walls at certain places to be fixed by making of grooves cutting 75mm minimum with making good surface are inlcuded in the cost of item itself. No extra cost shall be paid for the same. (ii) The pattern and design of sunshades to be fixed as per directions of Engr-in-charge.

M&L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde- E- 250) quality- A with dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed by Engineer-in-charge.

M&L Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde- E- 250) quality- A with dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified & directed by Engineer-in-charge.

M&L 5cm Sand stone slabs in sun-shades, chajjas, shelves, cills, landings, cover stones, templates, etc. n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4. including dismantling of Stone slabs in roofs, suspended floors, chajjas, landings, etc., any thickness, jointed in any mortar, complete all as specified & directed by Engineer-in-charge.

M&L for Granite 20mm thick table rubbed and polished in steps, jambs, pillars, window cills, cooking platform sand set in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixure of pigment to match with marble shade of Makrana white complete all as specified & directed by Engineer-in-charge.

M&L for Glazed ceramic colour tiles in vertical surface 350x250mmx7mm/ 450X350X7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 10mm thick rendering in CM 1:4 as backing coat including dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles), complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of dismantling floor hearthing or wall tiling, backing coat and tiling work.

M&L for Non-skid Ceramic coloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match laid over and including 15mm thick screed bed or bedding in CM (1:6) including dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of dismantling of floor hearthing or wall tiles, screed bed and floor tiles.

M & L Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:6 including dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of dismantling of floor hearthing or wall tiles, screed bed and floor tiles.

S&F 12mm thick Gypsum board in ceiling with 3mm thick wall care putty on ceiling alongwith and including Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre, including applying 3mm thick putty for making uniform smooth surface of ceiling and apply two coats of OBD and including dismantling existing false ceiling of any description complete all as specified and directed.

Taking down chowkats or frames exc 1.50 sqm but not exceeding 4 sqm each without taking off shutters from the frames including iron mongry complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames n.exc 1.50 sqm each, without taking off shutters from the frames including iron mongry complete all as specified & directed by Engineer-in-charge.

S&F Pressed steel door frame for doors made out of 1.2 mm thick sheet with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc size 165x60 mm, complete all as specified & directed by Engineer-in-charge.

S & F Plain, framed, panelled door shutters 35 mm thick in second class hard wood (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats complete all as specified & directed by Engineer-in-charge.

S&F 35 mm thick Glazed and skeleton shutters second class hard wood, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified & directed by Engineer-in-charge.

S&F steel ventilators with top hung shutters fitted with box type hinges including MS peg stays, MS handle and glazing bars dovetailed or welded for receiving glass including painting with one shop coat of zinc chromate primer,and cutting holes in wall for fixing the window lugs in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified & directed by Engineer-in-charge. Note : The rates quoted are inclusive of making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

S&F Butt hinges, 75mm medium weight, cold rolled mild steel complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium alloy handles cast type, each 125mm long complete all as specified & directed by Engineer-in-charge.

S&F Butt hinges, 100mm medium weight, cold rolled mild steel complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium alloy handles cast type, each 150mm long complete all as specified & directed by Engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 125mm long of extruded section complete all as specified & directed by Engineer-in-charge.

S&F Aluminium anodised, barrel tower bolts 75mm long of extruded section complete all as specified & directed by Engineer-in-charge.

M&L for Powder coated aluminium frame for doors, windows ventilators with one or more rebates including joining cleat for fixing etc. powder coating shall minimum thickness of power coating 50 micron complete all as specified & directed by Engineer-in-charge.

S&F Aluminium door shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, tower bolt, mortice lock, anodised aluminum snap beading screws etc. complete all as specified & directed by Engineer-in-charge.

S&F Aluminium window and ventilator shutters with powder coating of any colour (Thickness or powder coating not less than 50 micron), side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified & directed by Engineer-in-charge.

S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, complete all as specified & directed by Engineer-in-charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified & directed by Engineer-in-charge.

S&F 3.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exc 0.50 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

S&F Solar control film 25 micron reflective type exc 1.50 Sqm, sticked to glass panes as per instructions of manufacturers complete all as specified & directed by Engineer-in-charge.

S&F 12 mm Prelaminated Particle board, exterior grade, prelaminated both side with decorative choice laminations fixed with screws to timber frame work including taking down existing board of any description complete all as specified & directed by Engineer-in-charge.

S&F 18/19 mm Particle board for insulation purposes, fixed with nails to timber framework including taking down existing board of any description complete all as specified & directed by Engineer-in-charge.

S&F in repair, Aluminium (Die cast) body Door closer hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed complete all as specified & directed by Engineer-in-charge.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified & directed by Engineer-in-charge.

S&F 30mm thick of Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, uppling & fixing in the frame at site as per specification & drawing etc acomplete all as specified & directed by Engineer-in-charge.

S&F in repair of harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc complete all as specified & directed by Engineer-in-charge.

S&F in repairs tubular towel rail brass chromium plated 20mm dia D type 60cm long complete all as directed.

S&F in repair, Vitreous china bowl type urinal flat back, size of 465x355x265mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern) including flush pipe and waste pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and union for discharge pipe, (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified & directed by Engineer-in-charge.

S&F in repair, Urinal spreader chromium plated fixing with 15 mm dia pipe complete all as specified & directed by Engineer-in-charge.

M&L for preparing new or previously untreated wood and wood based surfaces of any description otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified & directed by Engineer-in-charge.

M&L 50 mm thick nominal mix M-15 grade concrete (1:2:4) type B1, (using 20mm graded stone aggregate) as in plinth protection and path laid in alternative bays finished even and smooth without using extra cement including mastic filling in joints complete all as specified & directed by Engineer-in-charge.

M&L for 15mm thick rendering in cement mortar 1:4 on stone masonry surfaces, finished even and smooth without using extra cement including taking down cement plaster of any description on stone masonry surface etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15mm thick on stone surfaces or other than fair faces of brick work or on one side of lathing in cement mortor 1:6, finished even and smooth without using extra cement complete including taking down cement plaster of any description on stone or brick walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distempering oil emulsion over a coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for prepration of new plastered wall surfaces of any description over 10cm girth or width, not otherwise described and applying two coat of Plastic emulsion paint over a coat of primer complete all as specified & directed by Engineer-in-charge.

S&F 1000 ltrs capacity white colour three layer rotational moulded polythene water storage tank (Cylinderical vertical with closed top) hoisted and fixed in position with 20mm bore dia ball brass valves high pressure, with polythene float and flynut screwed for iron pipe or brass ferrule including dismantling of existing tank with float valve complete all as specified & directed by Engineer-in-charge.

S&F in repair 20 mm bore gun metal globe or gate valve, with iron wheel head, screwed both ends for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair Kitchen sink with drainage board made of stainless steel 1mm thick with plugs, washers and wastes, incl bedding in cement mortar on to dwarf wall or incl fixing cantilever brackets and connecting union to pipe, over all size 915x460mm bowl size 410x330x160mm complete all as specified & directed by Engineer-in-charge.

S&F in repair, Vitreous china wash basin pedestal type, white, flat back, size 550x400 mm excluding taps, chain and plug and porcelain stopper but including CP waste coupling & brackets and fixed complete all as specified & directed by Engineer-in-charge.

S&F in repair Brass CP mixer of 15mm dia bore for mixing hot & cold water, screwed down for iron pipe and fixed, complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm dia Bib taps cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as specified & directed by Engineer-in-charge.

S&F in repairs 15mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed, complete all as specified & directed by Engineer-in-charge.

S&F in repair, PVC connection pipe 15mm dia, 450mm long with PTMT check nuts and washer on both ends complete all as specified & directed by Engineer-in-charge.

S&F 15 mm bore dia steel water tubing medium grade galvanised with and including necessary all fittings and fixtures complete fixed to walls and ceilings or laid in floors etc including taking down of old existing pipe complete all as specified & directed by Engineer-in-charge.

S&F 20 mm bore dia steel water tubing medium grade galvanised with and including necessary all fittings and fixtures complete fixed to walls and ceilings or laid in floors etc including taking down of old existing pipe complete all as specified & directed by Engineer-in-charge.

S&F in repair of Orissa pattern vitreous china squatting pan white of size 580x440mm with integral footrest (Excluding flushing cistern and flush pipes) but including concrete bedding and P or S trap as required including PVC pipe up to finished floor level to connect flush pipe, making good all the disturbed surfaces to match the adjoining complete all as specified & directed by Engineer-in-charge.

S&F in repair vitreous china wash down water closet pedestal pattern including connecting to flush tank, complete all as specified & directed by Engineer-in-charge.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern with inlet, ball valve, float, handle including fitting and fixtures and taking down the old damaged cisterns and providing connections to WC and flush pipe without any damage to the existing fittings, complete all as specified & directed by Engineer-in-charge.

S&F in repair, Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified & directed by Engineer-in-charge.

S & F in repair, Oval shape slim/Thin Rim ceramic wash basin size (19x13 inch)/Glossy finish/Counter top /Tableto bathroom sink/Super white colour including fancy type pillar tap, complete all as specified & directed by Engineer-in-charge.

S & F in repair, Single Piece-WC with PP soft close seat cover, Hinges, Fixing Accessories, Accessories Set and Cistern fittings, Size:360x640x685 mm, P Trap-180 mm complete all as specified & directed by Engineer-in-charge. Make :-Code : SLS-WHT-6851P180PP of Jaquar or equivlent in Appx 'C' list of makes.

S&F in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass of size 12 cm wide with CP bracket guard and railing 60 cm long complete all as specified & directed by Engineer-in-charge.

S&F in repair 15 mm bore Brass CP Wash hand Basin Mixture complete all as specified & directed by Engineer-in-charge. Make - ESSCO Cat No- MQT 516 A or equivlent in Appx 'C' list of makes.

S&F 5mm thick mirror fixed to wall with Brass CP screws with 4mm thick plywood backing complete including taking down old one complete all as specified & directed by Engineer-in-charge.

S&F Soap dish, any type, double soap socket each fixed to plugs with chromium plated brass screws complete all as specified & directed by Engineer-in-charge.

S&F for corner shelf made out of iron, powder coated fixed to wall with rust proof screws double layered each complete all as specified & directed by Engineer-in-charge.

S&F for corner shelf made out of glass 5.5mm thick with SS railing fixed to wall with SS screws complete all as specified & directed by Engineer-in-charge.

S&F for CP towel rack duoble decker with stand and hooks fixed to walls with suitable screws complete all as specified & directed by Engineer-in-charge.

S&F for CP peg set with 6 points fixed to walls complete all as specified & directed by Engineer-in-charge.

S&F for CP towel ring square shape fixed to wall complete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick plain cement concrete (1:4:8) type D-2 (using 40 mm graded stone aggregate) as in sub base of flooring/ hard standing & finished the surface even & fair without using extra cement complete all as specified and directed by Engineer-in-charge.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 25mm thick sand cushioning and including taking out/ dismantling the existing paver blocks and removing of debries out side MD land complete all as specified & directed by Engineer-in-charge. Note :- (i) Pattern of interlocking tile to be rubber moulded or equivalent as approved by GE. (ii) Rate quoted by the contractor shall deemed inclusive of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) packing and finished even and fair to the sides of pavement.

S&F Plate racks made of stainless steel 1mm thick with plugs, washers and wastes, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and overall size 750mmx 600mm complete all as specified and directed by Engineer-in-charge.

S&F in repairs brass chromium plated shower rose with swivel joints 125mm dia with 18mm dia chromium plated pipe complete all as specified and directed by Engineer-in-charge.

S&F 110 mm bore PVC (SWR) Soil, waste and vent pipes single socketed in any length with rubber ring joints laid in floors or trenches including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC (SWR) vent cowl any radius of 110 mm bore complete all as specified & directed by Engineer-in-charge.

M&L RCC hume pipes, class NP2, 150mm bore dia, with collars laid in trenches, set and jointed in cement mortar complete all as specified & directed by Engineer-in-charge.

M&L for PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) for concrete bed to drain pipe 150mm bore dia including packing under and haunching against the sides of pipe after they are laid and tested including demolition of existing concrete and breaking pipes of any description complete all as directed by Engr-in-Charge.

M&L for 35mm thick precast cement concrete (1:3:6) type C-0 (using 12.5mm graded stone aggregate) as in louvers or jallies (measured solid), including all mouldings but excluding frame, set in cement mortar (1:4) complete all as specified & directed by Engineer-in-charge.

M&L providing precast cement concrete (1:2:4) type B1 (using 20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps,columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone wallin). corbels, brackets, etc. (of any section indicated), withplain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match and set in CM (1:4) complete all as specified & directed by Engineer-in-charge.

S&F in repairs cast iron nahani trap with CP grating including jointing to waste pipe in cement mortar, diameter of out let 75mm bore fixed in cement concrete type B1 (1:2:4) complete all as specified & directed by Engineer-in-charge.

M&L for parking ceramic tiles Exterior Grade 300x300x10mm thick jointed in neat cement slurry and pointed in coloured cement as in floor laid over and including 15mm thick screed bed or bedding layer of cement mortar in CM (1:6) for laying floor finish with dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing, removing serviceable tiles) complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thick PCC 1:2:4 type B0 using 12.5mm graded stone aggregate as in subbase of floors, on roof top as padding & finishing the surface even & smooth without using extra cement including taking down and removal of existing roof treatment complete all as specified & directed by Engineer-in-charge.

M&L APP based polymeric membrane minimum weighing 3.5 Kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 160 gms/sqm) laid over primed surface including bituminous primer conforming to IS-3384 applied @ 0.40 Ltrs/Sqm by torched application complete all as specified & directed by Engineer-in-charge.

Taking down carefully surface aluminium or copper point wiring with PVC casing-caping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete all as specified & directed by Engineer-in-charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes complete all as specified & directed by Engineer-in-charge.

M&L Point wiring used approved colour coding as per IS (Red, Black and Green) for single phase circuits), with multi-stranded copper conductor 1.5 sqmm nominal cross -sectional area, single core, PVC insulated and unsheated FRLS cable 1100 volts grade, ISI 694 marked with valid CML No. in and including medium grade, PVC concealed conduit MMS, ISI marked of dia not less than 20 mm and conduit accessories conceled in wall/roof/floor etc, ISI marked with valid CML No. (IS-9537 - 1983 for condits and IS : 3419 - 1976 for conduit accessories) with terminated to new pressed flush metal boxes readily available cover with outer plates inner plates et, suitable for mounting modular type switches, socket fan regulator etc PVC insulated multistanded copper conductor 1.5 Sqmm nominal cross sectional area single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- Note : Modular switch and socket shall be measured and paid separately.Make: Polycab/Havells

One light point controlled by one switch

One ceiling/exhaust point controlled by one switch

One socket outlet 6 amp controlled by one switch on the same board with other switches.

All as per item No 93.00 here on before but with copper conductor cable of nominal class area 2.50 sq mm for phase, neutral & earth for One 2/3 pin socket outlet 5 Amps on independent board.

All as per item No 93.00 here on before but with copper conductor cable of nominal class area 4.0 sq mm for phase, neutral & earth for power socket point 15 Amps.

S& F modular switch one way 6A, 1 module complete all as specified & directed by Engineer-in-charge.

S&F modular socket 6A-2/3 pin combined 2 module complete all as specified & directed by Engineer-in-charge.

S&F modular switch socket combined 6A/16A , 6 pin, 3 module complete all as specified & directed by Engineer-in-charge.

S&F step type modular fan regulator 120W -2 module ISI Marked with valid CML No complete all as specified & directed by Engineer-in-charge.

S&F Ceiling rose, three terminals PVC/polycorbonate, isolated body complete all as specified & directed by Engineer-in-charge.

S&F vertical DBs TPN 4 way 415 V double door powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 250 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required,suitable for TP/FP MCCB as incomer including MCCB 100A 25 KA, 415 V complete all as specified & directed by Engineer-in-charge.

S&F for MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 8 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 40 to 63 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole 10 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

M&L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 10.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 10.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge. (Note :- Two runs of 10.00 Sqmm cable & one run of 10.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length)

M&L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 6.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 6.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge. (Note :- Two runs of 6.00 Sqmm cable & one run of 6.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length)

S&F Gyser/AC Box having 20 Amp MCB SP as incomer complete all as specified including taking down existing once complete all as specified & directed by Engineer-in-charge.

Supply and fixing of building security light fitting LED 35 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED as lihjting souce and PC cover having TOP opening sepreate drive compartment etc and connecting complete all as specified & directed by Engineer-in-charge.

S&F bracket of GI pipe medium grade of 40mm dia, 1.2 meter in length clamps made of FI 40 mm x 6mm incl nuts, bolts & washers, painting and including taking down existing bracket complete all as specified & directed by Engineer-in-charge.

S&F surface and wall mounted LED tube light along with fixture, 4 ft, 20W, extruded aluminium housing provided for efficient heat disspation with polycarbonate, operating voltage 240 V, 50HZ, AC supply and operating tempureture 0 to 50 C, power factor >0.9, lumen output > 2000 and provision of new 3 core multistanded copper conductor of size 23/0.193 from ceiling rose to fitting with white colour flexible pipe complete all as specified & directed by Engineer-in-charge.

Supply and fixing of recessed/ceiling mounted down lighter with CRCA housing with high bright LED, idealy suited for low ceiling areas Brilliance 36watt LED, size 2ft x 2ft The product features color tuning from 3000 K to 6500 K, necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting with white color flexible pipe complete all as specified & directed by Engineer-in-charge.

S & F of LED tube light fitting 10 watt tube LED Neutral white in colour, 600 mm in length wall mounted LED batten, extruded aluminium heat shink provided for efficient heat dissipation & integrated electronic driver, optic diffused type ENDURA LINER NEO including all electric connection with whilte flexible cord 1.50 Sqmm 3 core as required complete all as specified & directed by Engineer-in-charge.

S&F for LED post top lantern/gate Light 40 watt light fitting made of cast aluminium spigot housing with decarative opal acrylic diffuser with IP 65 protection complete with all accessories including removal of old unserviceable light fitting complete all as specified & directed by Engineer-in-charge.

Supply and fixing of PVC insulated copper conductor 2.5 sq mm 3 core in PVC conduit medium grade in ground/surface with necessary fixing arrengment and connecting items complete all as specified & directed by Engineer-in-charge.

S&F fans ceiling fans with three blade, down rod, accessories 230 V, 1200 mm sweep including necessary connecting cable complete all as specified & directed by Engineer-in-charge. Note :- The rate quoted by the contractor shall deemed to inclusive of suitable size/ length of down take rod and length of cable as per site requirement.

S&F wall mounted fan AC, single phase 230V of size 400mm sweep with blades and frame and louvers complete all as specified & directed by Engineer-in-charge.

S&F Steel body heavy duty exhaust fans AC single phase 230/ 240 V of size 300 mm sweep with louver complete all as specified & directed by Engineer-in-charge.

Supply & fix water heater storage type (Geyser) vertical type ,inner container of capacity 25 ltrs, power Consumption 2.0 KW, BEE 5 star rated pressure rating >8 Bar electrically operated ,AC 230 Volts ,including as per site required Nos of fashner nuts required suitable size fixed in brick wall, BEE 5 star rated complete all as specified & directed by Engineer-in-charge. Make: Havells Cat pot No : Monza DX GHWAMGTWH025 or equivalent in Appx 'C' list of makes.

Cutting holes in stone/ brick/ block masonry walls of size suitable for fixing of 300mm sweep exhaust fan and making good the disturbed surface as per existing surface of wall complete all as specified & directed by Engineer-in-charge.

Taking down ceiling fan/ exhaust fan of any sweep, dismanting blade and including preparation, filling cavity with putty and applying one coat of synthetic enamel paint by means of mechanical spraying machine and re-assembling the fan and re-fixing in its original position or any other position complete all as specified & directed by Engineer-in-charge. Note :- Rate quoted by the contractor shall deemed to inclusive of replacing of quarter pin, nut bolt with check nut, rubber real etc.

Taking down storage geyser of any capacity after disconnecting electrical connection from existing socket, removing the bolts and nuts from wall and disconnected inlet and outlet water connection including preparation of surface and apply synthetic enamel paint by spraying with machine including filling cavity with filler one coat and including refixing the geyser it's original location after repair/replacing the unsv items like heating element, thermostat, PVC connection pipe of hot & cold type changing of outer body with its inner tank if found unservicable, making Geyer serviceable in all respect complete all as specified and directed by Engineer -in-Charge. (Note :- Rate Quated by Contractor shall be inclusive for replacing all unsv item like Sefty valve, Heating element, Thermostat, PVC Connection pipe of hot & cold type, Changing of outer body with its inner tank ete).

M&L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground level connected to galvanized iron wire 4 mm dia as earthing lead up to Panel /DB BOX as per site requirement by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection including test point terminal cover the earhing hole by PCC chamber and GI cover and testing on completion and including taking down existing earthing complete all as specified & directed by Engineer-in-charge.

NOTE FOR ITEM No. 123.00 [i]. Excavation & earth work in any type of soil including removing of surplus material upto 100M [ii]. PCC (1:3:6) type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC (1:2:4) type B1 cover 50x50 cm with 8mm round bar @ 15 cm C/C both ways. [iii]. Main earthing wire from earth electrode to test point upto 7.5 mtr. [iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs and charcoal & salt as reqd. [v]. GI protection pipe of size 40 mm bore light grade 7.5m.

M&L earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or fixed to DBs or any other indicated situation for loop earthing with GI wire 4 mm mm size including taking down existing unserviceable earthing strip complete all as specified & directed by Engineer-in-charge.

S&F GI Tubing light grade 20 mm dia for cable protection including taking down existing unserviceable pipe complete all as specified & directed by Engineer-in-charge.

Supply, laying, testing and commissioning of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade with stranded aluminium conductor of size of cross sectional aera 35 Sqmm 3½ core with cable lugs, gland etc including taking down old unsv existing cable complete all as specified & directed by Engineer-in-Charge.

Supply, laying, testing and commissioning of cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured electric power cable (heavy duty) 1100 volt grade with stranded aluminium conductor of size of cross sectional aera 10 Sqmm 2 core with cable lugs, gland etc including taking down old unsv existing cable complete all as specified & directed by Engineer-in-Charge.

S&F steel water tubing 40 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

M&L for sand cushioning to under ground cable using tibba sand and gently punning to cushioning to cable complete all as directed by Engineer-in-Charge. (Note :- Punned thickness of sand cushioning shall only measured for the purpose of payment).

Supply & laying unreinforced precast concrete cable covers class LV type-I flat size 250 mm x 150 mm x40 mm complete all as specified and directed by Engr-in-Charge .

M& road cutting in trenches for laying cable protection pipe including making good the surface with top 200mm thick shall filled with PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) complete all as specified & directed by Engineer-in-charge. Note :- (i) Rate quoted by the Contractor shall deemed to inclusive of road cutting, earth work, excavation & PCC. (ii) Supply and laying of pipe will be measured and paid seperately.

M/s Shree Construction Company

AMBEY MAA CONSTRUCTION COMPANY

GEMRARAMCONTRACTOR

deepaktraders

Bhawani Constructions

M/S MAYA CONSTRUCTION COMPANY